Root.sh failed on second node while installing CRS 10g on centos 5.5

root.sh failed on second node while installing CRS 10g
Hi all,
I am able to install Oracle 10g RAC clusterware on first node of the cluster. However, when I run the root.sh script as root
user on second node of the cluster, it fails with following error message:
NO KEYS WERE WRITTEN. Supply -force parameter to override.
-force is destructive and will destroy any previous cluster
configuration.
Oracle Cluster Registry for cluster has already been initialized
Startup will be queued to init within 90 seconds.
Adding daemons to inittab
Expecting the CRS daemons to be up within 600 seconds.
Failure at final check of Oracle CRS stack.
10
and run cluvfy stage -post hwos -n all -verbose,it show message:
ERROR:
Could not find a suitable set of interfaces for VIPs.
Result: Node connectivity check failed.
Checking shared storage accessibility...
Disk Sharing Nodes (2 in count)
/dev/sda db2 db1
and run cluvfy stage -pre crsinst -n all -verbose,it show message:
ERROR:
Could not find a suitable set of interfaces for VIPs.
Result: Node connectivity check failed.
Checking system requirements for 'crs'...
No checks registered for this product.
and run cluvfy stage -post crsinst -n all -verbose,it show message:
Result: Node reachability check passed from node "DB2".
Result: User equivalence check passed for user "oracle".
Node Name CRS daemon CSS daemon EVM daemon
db2 no no no
db1 yes yes yes
Check: Health of CRS
Node Name CRS OK?
db1 unknown
Result: CRS health check failed.
check crsd.log and show message:
clsc_connect: (0x143ca610) no listener at (ADDRESS=(PROTOCOL=ipc)(KEY=OCSSD_LL_db2_crs))
clsssInitNative: connect failed, rc 9
Any help would be greatly appreciated.
Edited by: 868121 on 2011-6-24 上午12:31

Hello, it took a little searching, but I found this in a note in the GRID installation guide for Linux/UNIX:
Public IP addresses and virtual IP addresses must be in the same subnet.
In your case, you are using two different subnets for the VIPs.

Similar Messages

Error while installing oracle 10g on centos 5.6 32 Bit

Hi All,
Please help me with the issue I facing while installing oracle 10g on centos 5.6 32bit. I did lot of research on google but I am getting same answer...the libXp package is missing, but I have check it...its already installed.
[root@staging ~]# find / -name libXp.so.6
/usr/lib/libXp.so.6
/usr/lib64/libXp.so.6
echo $DISPLAY
<ipaddress>:0.0
[oracle@staging database]$ DISPLAY=<ipaddress>:0.0; export DISPLAY
[oracle@staging database]$ id
uid=500(oracle) gid=500(oinstall) groups=500(oinstall),501(dba) context=root:system_r:unconfined_t:SystemLow-SystemHigh
Below is the error message I am getting :
oracle@staging database]$ ./runInstaller
Starting Oracle Universal Installer...
Checking installer requirements...
Checking operating system version: must be redhat-3, SuSE-9, redhat-4, UnitedLinux-1.0, asianux-1 or asianux-2
Passed
All installer requirements met.
Preparing to launch Oracle Universal Installer from /tmp/OraInstall2012-06-27_05-37-17PM. Please wait ...[oracle@staging database]$ Exception in thread "main" java.lang.UnsatisfiedLinkError: /tmp/OraInstall2012-06-27_05-37-17PM/jre/1.4.2/lib/i386/libawt.so: libXtst.so.6: cannot open shared object file: No such file or directory
     at java.lang.ClassLoader$NativeLibrary.load(Native Method)
     at java.lang.ClassLoader.loadLibrary0(Unknown Source)
     at java.lang.ClassLoader.loadLibrary(Unknown Source)
     at java.lang.Runtime.loadLibrary0(Unknown Source)
     at java.lang.System.loadLibrary(Unknown Source)
     at sun.security.action.LoadLibraryAction.run(Unknown Source)
     at java.security.AccessController.doPrivileged(Native Method)
     at sun.awt.NativeLibLoader.loadLibraries(Unknown Source)
     at sun.awt.DebugHelper.<clinit>(Unknown Source)
     at java.awt.Component.<clinit>(Unknown Source)
I found some suggestion on google and tried to not use ip address in DISPLAY settings...
if I am using 0.0 instead of IP below eg.
[oracle@staging database]$ DISPLAY=:0.0; export DISPLAY
The error I am receiving differnt error
[oracle@staging database]$ ./runInstaller
Starting Oracle Universal Installer...
Checking installer requirements...
Checking operating system version: must be redhat-3, SuSE-9, redhat-4, UnitedLinux-1.0, asianux-1 or asianux-2
Passed
All installer requirements met.
Preparing to launch Oracle Universal Installer from /tmp/OraInstall2012-06-27_05-34-40PM. Please wait ...
DISPLAY not set. Please set the DISPLAY and try again.
Depending on the Unix Shell, you can use one of the following commands as examples to set the DISPLAY environment variable:
- For csh:                % setenv DISPLAY 192.168.1.128:0.0
- For sh, ksh and bash:      $ DISPLAY=192.168.1.128:0.0; export DISPLAY
Use the following command to see what shell is being used:
     echo $SHELL
Use the following command to view the current DISPLAY environment variable setting:
     echo $DISPLAY
- Make sure that client users are authorized to connect to the X Server.
To enable client users to access the X Server, open an xterm, dtterm or xconsole as the user that started the session and type the following command:
% xhost +
To test that the DISPLAY environment variable is set correctly, run a X11 based program that comes with the native operating system such as 'xclock':
     % <full path to xclock.. see below>
If you are not able to run xclock successfully, please refer to your PC-X Server or OS vendor for further assistance.
Typical path for xclock: /usr/X11R6/bin/xclock
[oracle@staging database]$ echo $SHELL
/bin/bash
Please help me.

satish.ygl wrote:
Hi,
I am getting the same error when i am applying patchset to 10201 to 10204. I am using RedHat Linux 4 version and I tried set $DISPLAY=<hostname/ip address>:0.0 and export=DISPLAY
#xhost + and checked $PATH this is also is correct
I did these steps still i am getting the following error
pen an xterm, dtterm or xconsole as the user that started the session and type the following command:
% xhost +
To test that the DISPLAY environment variable is set correctly, run a X11 based program that comes with the native operating system such as 'xclock':
% <full path to xclock... see below>
If you are not able to run xclock successfully, please refer to your PC-X Server or OS vendor for further assistance.
Typical path for 'xclock': '/usr/X11R6/bin/xclock'
Please help me in this scenario.
thank You,
Sri
Edited by: satish.ygl on Oct 30, 2012 7:49 PMyou must log onto the DB Server as below (or functional equivalent)
ssh -X oracle@DB_Server
& the first & only command after logging onto the DB Server should be as below
xclock
If/when xclock fails, then OUI will fail.

Root.sh fails on second node

I already posted this issue on database installation forum, and was suggested to post it on this forum.
Here are the details.
I am running Linux 64bit on ESx clients. Installing Oracle 11gR2.
It passed all the per-requisite. Run root.sh on first node. It finished with no errorrs.
On second node I got the following:
Running Oracle 11g root.sh script...
The following environment variables are set as:
ORACLE_OWNER= oracle
ORACLE_HOME= /u01/app/11.2.0/grid
Enter the full pathname of the local bin directory: [usr/local/bin]:
The file "dbhome" already exists in /usr/local/bin. Overwrite it? (y/n)
[n]:
The file "oraenv" already exists in /usr/local/bin. Overwrite it? (y/n)
[n]:
The file "coraenv" already exists in /usr/local/bin. Overwrite it? (y/n)
[n]:
Entries will be added to the /etc/oratab file as needed by
Database Configuration Assistant when a database is created
Finished running generic part of root.sh script.
Now product-specific root actions will be performed.
2010-07-13 12:51:28: Parsing the host name
2010-07-13 12:51:28: Checking for super user privileges
2010-07-13 12:51:28: User has super user privileges
Using configuration parameter file: /u01/app/11.2.0/grid/crs/install/crsconfig_params
Creating trace directory
LOCAL ADD MODE
Creating OCR keys for user 'root', privgrp 'root'..
Operation successful.
Adding daemon to inittab
CRS-4123: Oracle High Availability Services has been started.
ohasd is starting
CRS-4402: The CSS daemon was started in exclusive mode but found an active CSS daemon on node fred0224, number 1, and is terminating
An active cluster was found during exclusive startup, restarting to join the cluster
CRS-2672: Attempting to start 'ora.mdnsd' on 'fred0225'
CRS-2676: Start of 'ora.mdnsd' on 'fred0225' succeeded
CRS-2672: Attempting to start 'ora.gipcd' on 'fred0225'
CRS-2676: Start of 'ora.gipcd' on 'fred0225' succeeded
CRS-2672: Attempting to start 'ora.gpnpd' on 'fred0225'
CRS-2676: Start of 'ora.gpnpd' on 'fred0225' succeeded
CRS-2672: Attempting to start 'ora.cssdmonitor' on 'fred0225'
CRS-2676: Start of 'ora.cssdmonitor' on 'fred0225' succeeded
CRS-2672: Attempting to start 'ora.cssd' on 'fred0225'
CRS-2672: Attempting to start 'ora.diskmon' on 'fred0225'
CRS-2676: Start of 'ora.diskmon' on 'fred0225' succeeded
CRS-2676: Start of 'ora.cssd' on 'fred0225' succeeded
CRS-2672: Attempting to start 'ora.ctssd' on 'fred0225'
Start action for octssd aborted
CRS-2676: Start of 'ora.ctssd' on 'fred0225' succeeded
CRS-2672: Attempting to start 'ora.drivers.acfs' on 'fred0225'
CRS-2672: Attempting to start 'ora.asm' on 'fred0225'
CRS-2676: Start of 'ora.drivers.acfs' on 'fred0225' succeeded
CRS-2676: Start of 'ora.asm' on 'fred0225' succeeded
CRS-2664: Resource 'ora.ctssd' is already running on 'fred0225'
CRS-4000: Command Start failed, or completed with errors.
Command return code of 1 (256) from command: /u01/app/11.2.0/grid/bin/crsctl start resource ora.asm -init
Start of resource "ora.asm -init" failed
Failed to start ASM
Failed to start Oracle Clusterware stack
In the ocssd.log I found
[ CSSD][3559689984]clssnmvDHBValidateNCopy: node 1, fred0224, has a disk HB, but no network HB, DHB has rcfg 174483948, wrtcnt, 232, LATS 521702664, lastSeqNo 232, uniqueness 1279039649, timestamp 1279039959/521874274
In oraagent_oracle.log I found
[ clsdmc][1212365120]Fail to connect (ADDRESS=(PROTOCOL=ipc)(KEY=fred0225DBG_GPNPD)) with status 9
2010-07-13 12:54:07.234: [ora.gpnpd][1212365120] [check] Error = error 9 encountered when connecting to GPNPD
2010-07-13 12:54:07.238: [ora.gpnpd][1212365120] [check] Calling PID check for daemon
2010-07-13 12:54:07.238: [ora.gpnpd][1212365120] [check] Trying to check PID = 20584
2010-07-13 12:54:07.432: [ COMMCRS][1285794112]clsc_connect: (0x1304d850) no listener at (ADDRESS=(PROTOCOL=ipc)(KEY=fred0225DBG_GPNPD))
[ clsdmc][1222854976]Fail to connect (ADDRESS=(PROTOCOL=ipc)(KEY=fred0225DBG_MDNSD)) with status 9
2010-07-13 12:54:08.649: [ora.mdnsd][1222854976] [check] Error = error 9 encountered when connecting to MDNSD
2010-07-13 12:54:08.649: [ora.mdnsd][1222854976] [check] Calling PID check for daemon
2010-07-13 12:54:08.649: [ora.mdnsd][1222854976] [check] Trying to check PID = 20571
2010-07-13 12:54:08.841: [ COMMCRS][1201875264]clsc_connect: (0x12f3b1d0) no listener at (ADDRESS=(PROTOCOL=ipc)(KEY=fred0225DBG_MDNSD))
[ clsdmc][1159915840]Fail to connect (ADDRESS=(PROTOCOL=ipc)(KEY=fred0225DBG_GIPCD)) with status 9
2010-07-13 12:54:10.051: [ora.gipcd][1159915840] [check] Error = error 9 encountered when connecting to GIPCD
2010-07-13 12:54:10.051: [ora.gipcd][1159915840] [check] Calling PID check for daemon
2010-07-13 12:54:10.051: [ora.gipcd][1159915840] [check] Trying to check PID = 20566
2010-07-13 12:54:10.242: [ COMMCRS][1254324544]clsc_connect: (0x12f35630) no listener at (ADDRESS=(PROTOCOL=ipc)(KEY=fred0225DBG_GIPCD))
In oracssdagent_root.log I found
2010-07-13 12:52:28.698: [ CSSCLNT][1102481728]clssscConnect: gipc request failed with 29 (0x16)
2010-07-13 12:52:28.698: [ CSSCLNT][1102481728]clsssInitNative: connect failed, rc 29
2010-07-13 12:53:55.222: [ CSSCLNT][1102481728]clssnsqlnum: RPC failed rc 3
2010-07-13 12:53:55.222: [ USRTHRD][1102481728] clsnomon_cssini: failed 3 to fetch node number
2010-07-13 12:53:55.222: [ USRTHRD][1102481728] clsnomon_init: css init done, nodenum -1.
2010-07-13 12:53:55.222: [ CSSCLNT][1102481728]clsssRecvMsg: got a disconnect from the server while waiting for message type 43
2010-07-13 12:53:55.222: [ CSSCLNT][1102481728]clsssGetNLSData: Failure receiving a msg, rc 3
If you need more info, let me know.

Well, the error clearly indicates that a communication problem exists on the private interconnect.
Could this be a setting in ESX, which prevents some communication between the clients on the second network card? Any routing table in ESX not configured correctly?
Sebastian

Root.sh failed at second node OUL 6.3 Oracle GRID 11.2.0.3

Hi, im installing a two node cluster mounted on Oracle Linux 6.3 with Oracle DB 11.2.0.3, the installation went smooth up until the execution of the root.sh script on the second node.
THe script return this final lines:
CRS-4402: The CSS daemon was started in exclusive mode but found an active CSS daemon on node nodo1, number 1, and is terminating
An active cluster was found during exclusive startup, restarting to join the cluster
Start of resource "ora.crsd" failed
CRS-2800: Cannot start resource 'ora.asm' as it is already in the INTERMEDIATE state on server 'nodo2'
CRS-4000: Command Start failed, or completed with errors.
Failed to start Oracle Grid Infrastructure stack
Failed to start Cluster Ready Services at /u01/app/11.2.0/grid/crs/install/crsconfig_lib.pm line 1286.
/u01/app/11.2.0/grid/perl/bin/perl -I/u01/app/11.2.0/grid/perl/lib -I/u01/app/11.2.0/grid/crs/install /u01/app/11.2.0/grid/crs/install/rootcrs.pl execution failed
In $GRID_HOME/log/node2/alertnode.log It appears to be a Cluster Time Synchronization Service issue, (i didn't synchronyze the nodes..) however the CTSS is running in observer mode, wich i believe it shouldn't affect the installation process. After that i lost it...there's an entry CRS-5018 indicating that an unused HAIP route was removed... and then, out of the blue: CRS-5818:Aborted command 'start' for resource 'ora.asm'. Some clarification will be deeply apreciated.
Here's the complete log:
2013-04-01 13:39:35.358
[client(12163)]CRS-2101:The OLR was formatted using version 3.
2013-04-01 19:40:19.597
[ohasd(12338)]CRS-2112:The OLR service started on node nodo2.
2013-04-01 19:40:19.657
[ohasd(12338)]CRS-1301:Oracle High Availability Service started on node nodo2.
[client(12526)]CRS-10001:01-Apr-13 13:41 ACFS-9459: ADVM/ACFS is not supported on this OS version: '2.6.39-400.17.2.el6uek.i686'
[client(12528)]CRS-10001:01-Apr-13 13:41 ACFS-9201: Not Supported
[client(12603)]CRS-10001:01-Apr-13 13:41 ACFS-9459: ADVM/ACFS is not supported on this OS version: '2.6.39-400.17.2.el6uek.i686'
2013-04-01 19:41:17.509
[ohasd(12338)]CRS-2302:Cannot get GPnP profile. Error CLSGPNP_NO_DAEMON (GPNPD daemon is not running).
2013-04-01 19:41:17.618
[gpnpd(12695)]CRS-2328:GPNPD started on node nodo2.
2013-04-01 19:41:21.363
[cssd(12755)]CRS-1713:CSSD daemon is started in exclusive mode
2013-04-01 19:41:23.194
[ohasd(12338)]CRS-2767:Resource state recovery not attempted for 'ora.diskmon' as its target state is OFFLINE
2013-04-01 19:41:56.144
[cssd(12755)]CRS-1707:Lease acquisition for node nodo2 number 2 completed
2013-04-01 19:41:57.545
[cssd(12755)]CRS-1605:CSSD voting file is online: /dev/oracleasm/disks/ASM_DISK_1; details in /u01/app/11.2.0/grid/log/nodo2/cssd/ocssd.log.
[cssd(12755)]CRS-1636:The CSS daemon was started in exclusive mode but found an active CSS daemon on node nodo1 and is terminating; details at (:CSSNM00006:) in /u01/app/11.2.0/grid/log/nodo2/cssd/ocssd.log
2013-04-01 19:41:58.549
[ohasd(12338)]CRS-2765:Resource 'ora.cssdmonitor' has failed on server 'nodo2'.
2013-04-01 19:42:10.025
[gpnpd(12695)]CRS-2329:GPNPD on node nodo2 shutdown.
2013-04-01 19:42:11.407
[mdnsd(12685)]CRS-5602:mDNS service stopping by request.
2013-04-01 19:42:29.642
[gpnpd(12947)]CRS-2328:GPNPD started on node nodo2.
2013-04-01 19:42:33.241
[cssd(13012)]CRS-1713:CSSD daemon is started in clustered mode
2013-04-01 19:42:35.104
[ohasd(12338)]CRS-2767:Resource state recovery not attempted for 'ora.diskmon' as its target state is OFFLINE
2013-04-01 19:42:44.065
[cssd(13012)]CRS-1707:Lease acquisition for node nodo2 number 2 completed
2013-04-01 19:42:45.484
[cssd(13012)]CRS-1605:CSSD voting file is online: /dev/oracleasm/disks/ASM_DISK_1; details in /u01/app/11.2.0/grid/log/nodo2/cssd/ocssd.log.
2013-04-01 19:42:52.138
[cssd(13012)]CRS-1601:CSSD Reconfiguration complete. Active nodes are nodo1 nodo2 .
2013-04-01 19:42:55.081
[ctssd(13076)]CRS-2403:The Cluster Time Synchronization Service on host nodo2 is in observer mode.
2013-04-01 19:42:55.581
[ctssd(13076)]CRS-2401:The Cluster Time Synchronization Service started on host nodo2.
2013-04-01 19:42:55.581
[ctssd(13076)]CRS-2407:The new Cluster Time Synchronization Service reference node is host nodo1.
2013-04-01 19:43:08.875
[ctssd(13076)]CRS-2412:The Cluster Time Synchronization Service detects that the local time is significantly different from the mean cluster time. Details in /u01/app/11.2.0/grid/log/nodo2/ctssd/octssd.log.
2013-04-01 19:43:08.876
[ctssd(13076)]CRS-2409:The clock on host nodo2 is not synchronous with the mean cluster time. No action has been taken as the Cluster Time Synchronization Service is running in observer mode.
2013-04-01 19:43:13.565
[u01/app/11.2.0/grid/bin/orarootagent.bin(13064)]CRS-5018:(:CLSN00037:) Removed unused HAIP route: 169.254.0.0 / 255.255.0.0 / 0.0.0.0 / eth0
2013-04-01 19:53:09.800
[u01/app/11.2.0/grid/bin/oraagent.bin(12922)]CRS-5818:Aborted command 'start' for resource 'ora.asm'. Details at (:CRSAGF00113:) {0:0:223} in /u01/app/11.2.0/grid/log/nodo2/agent/ohasd/oraagent_oracle/oraagent_oracle.log.
2013-04-01 19:53:11.827
[ohasd(12338)]CRS-2757:Command 'Start' timed out waiting for response from the resource 'ora.asm'. Details at (:CRSPE00111:) {0:0:223} in /u01/app/11.2.0/grid/log/nodo2/ohasd/ohasd.log.
2013-04-01 19:53:12.779
[u01/app/11.2.0/grid/bin/oraagent.bin(12922)]CRS-5019:All OCR locations are on ASM disk groups [DATA], and none of these disk groups are mounted. Details are at "(:CLSN00100:)" in "/u01/app/11.2.0/grid/log/nodo2/agent/ohasd/oraagent_oracle/oraagent_oracle.log".
2013-04-01 19:53:13.892
[u01/app/11.2.0/grid/bin/oraagent.bin(12922)]CRS-5019:All OCR locations are on ASM disk groups [DATA], and none of these disk groups are mounted. Details are at "(:CLSN00100:)" in "/u01/app/11.2.0/grid/log/nodo2/agent/ohasd/oraagent_oracle/oraagent_oracle.log".
2013-04-01 19:53:43.877
[u01/app/11.2.0/grid/bin/oraagent.bin(12922)]CRS-5019:All OCR locations are on ASM disk groups [DATA], and none of these disk groups are mounted. Details are at "(:CLSN00100:)" in "/u01/app/11.2.0/grid/log/nodo2/agent/ohasd/oraagent_oracle/oraagent_oracle.log".
2013-04-01 19:54:13.891
[u01/app/11.2.0/grid/bin/oraagent.bin(12922)]CRS-5019:All OCR locations are on ASM disk groups [DATA], and none of these disk groups are mounted. Details are at "(:CLSN00100:)" in "/u01/app/11.2.0/grid/log/nodo2/agent/ohasd/oraagent_oracle/oraagent_oracle.log".
2013-04-01 19:54:43.906
[u01/app/11.2.0/grid/bin/oraagent.bin(12922)]CRS-5019:All OCR locations are on ASM disk groups [DATA], and none of these disk groups are mounted. Details are at "(:CLSN00100:)" in "/u01/app/11.2.0/grid/log/nodo2/agent/ohasd/oraagent_oracle/oraagent_oracle.log".
2013-04-01 19:55:13.914
[u01/app/11.2.0/grid/bin/oraagent.bin(12922)]CRS-5019:All OCR locations are on ASM disk groups [DATA], and none of these disk groups are mounted. Details are at "(:CLSN00100:)" in "/u01/app/11.2.0/grid/log/nodo2/agent/ohasd/oraagent_oracle/oraagent_oracle.log".
2013-04-01 19:55:43.918
[u01/app/11.2.0/grid/bin/oraagent.bin(12922)]CRS-5019:All OCR locations are on ASM disk groups [DATA], and none of these disk groups are mounted. Details are at "(:CLSN00100:)" in "/u01/app/11.2.0/grid/log/nodo2/agent/ohasd/oraagent_oracle/oraagent_oracle.log".
2013-04-01 19:56:13.922
[u01/app/11.2.0/grid/bin/oraagent.bin(12922)]CRS-5019:All OCR locations are on ASM disk groups [DATA], and none of these disk groups are mounted. Details are at "(:CLSN00100:)" in "/u01/app/11.2.0/grid/log/nodo2/agent/ohasd/oraagent_oracle/oraagent_oracle.log".
2013-04-01 19:56:53.209
[crsd(13741)]CRS-1012:The OCR service started on node nodo2.
2013-04-01 20:07:01.128
[crsd(13741)]CRS-0810:Cluster Ready Service aborted due to failure to communicate with Event Management Service with error [1]. Details at (:CRSD00120:) in /u01/app/11.2.0/grid/log/nodo2/crsd/crsd.log.
2013-04-01 20:07:01.278
[ohasd(12338)]CRS-2765:Resource 'ora.crsd' has failed on server 'nodo2'.
2013-04-01 20:07:08.689
[crsd(15248)]CRS-1012:The OCR service started on node nodo2.
2013-04-01 20:13:10.138
[ctssd(13076)]CRS-2412:The Cluster Time Synchronization Service detects that the local time is significantly different from the mean cluster time. Details in /u01/app/11.2.0/grid/log/nodo2/ctssd/octssd.log.
2013-04-01 20:17:13.024
[crsd(15248)]CRS-0810:Cluster Ready Service aborted due to failure to communicate with Event Management Service with error [1]. Details at (:CRSD00120:) in /u01/app/11.2.0/grid/log/nodo2/crsd/crsd.log.
2013-04-01 20:17:13.171
[ohasd(12338)]CRS-2765:Resource 'ora.crsd' has failed on server 'nodo2'.
2013-04-01 20:17:20.826
[crsd(16746)]CRS-1012:The OCR service started on node nodo2.
2013-04-01 20:27:25.020
[crsd(16746)]CRS-0810:Cluster Ready Service aborted due to failure to communicate with Event Management Service with error [1]. Details at (:CRSD00120:) in /u01/app/11.2.0/grid/log/nodo2/crsd/crsd.log.
2013-04-01 20:27:25.176
[ohasd(12338)]CRS-2765:Resource 'ora.crsd' has failed on server 'nodo2'.
2013-04-01 20:27:31.591
[crsd(18266)]CRS-1012:The OCR service started on node nodo2.
2013-04-01 20:37:35.668
[crsd(18266)]CRS-0810:Cluster Ready Service aborted due to failure to communicate with Event Management Service with error [1]. Details at (:CRSD00120:) in /u01/app/11.2.0/grid/log/nodo2/crsd/crsd.log.
2013-04-01 20:37:35.808
[ohasd(12338)]CRS-2765:Resource 'ora.crsd' has failed on server 'nodo2'.
2013-04-01 20:37:43.209
[crsd(19762)]CRS-1012:The OCR service started on node nodo2.
2013-04-01 20:43:11.160
[ctssd(13076)]CRS-2412:The Cluster Time Synchronization Service detects that the local time is significantly different from the mean cluster time. Details in /u01/app/11.2.0/grid/log/nodo2/ctssd/octssd.log.
2013-04-01 20:47:47.487
[crsd(19762)]CRS-0810:Cluster Ready Service aborted due to failure to communicate with Event Management Service with error [1]. Details at (:CRSD00120:) in /u01/app/11.2.0/grid/log/nodo2/crsd/crsd.log.
2013-04-01 20:47:47.637
[ohasd(12338)]CRS-2765:Resource 'ora.crsd' has failed on server 'nodo2'.
2013-04-01 20:47:55.086
[crsd(21242)]CRS-1012:The OCR service started on node nodo2.
2013-04-01 20:57:59.343
[crsd(21242)]CRS-0810:Cluster Ready Service aborted due to failure to communicate with Event Management Service with error [1]. Details at (:CRSD00120:) in /u01/app/11.2.0/grid/log/nodo2/crsd/crsd.log.
2013-04-01 20:57:59.492
[ohasd(12338)]CRS-2765:Resource 'ora.crsd' has failed on server 'nodo2'.
2013-04-01 20:58:06.996
[crsd(22744)]CRS-1012:The OCR service started on node nodo2.
2013-04-01 21:08:11.046
[crsd(22744)]CRS-0810:Cluster Ready Service aborted due to failure to communicate with Event Management Service with error [1]. Details at (:CRSD00120:) in /u01/app/11.2.0/grid/log/nodo2/crsd/crsd.log.
2013-04-01 21:08:11.192
[ohasd(12338)]CRS-2765:Resource 'ora.crsd' has failed on server 'nodo2'.
2013-04-01 21:08:18.726
[crsd(24260)]CRS-1012:The OCR service started on node nodo2.
2013-04-01 21:13:12.000
[ctssd(13076)]CRS-2412:The Cluster Time Synchronization Service detects that the local time is significantly different from the mean cluster time. Details in /u01/app/11.2.0/grid/log/nodo2/ctssd/octssd.log.
2013-04-01 21:18:22.262
[crsd(24260)]CRS-0810:Cluster Ready Service aborted due to failure to communicate with Event Management Service with error [1]. Details at (:CRSD00120:) in /u01/app/11.2.0/grid/log/nodo2/crsd/crsd.log.
2013-04-01 21:18:22.411
[ohasd(12338)]CRS-2765:Resource 'ora.crsd' has failed on server 'nodo2'.
2013-04-01 21:18:29.927
[crsd(25759)]CRS-1012:The OCR service started on node nodo2.
2013-04-01 21:28:34.467
[crsd(25759)]CRS-0810:Cluster Ready Service aborted due to failure to communicate with Event Management Service with error [1]. Details at (:CRSD00120:) in /u01/app/11.2.0/grid/log/nodo2/crsd/crsd.log.
2013-04-01 21:28:34.616
[ohasd(12338)]CRS-2765:Resource 'ora.crsd' has failed on server 'nodo2'.
2013-04-01 21:28:41.990
[crsd(27291)]CRS-1012:The OCR service started on node nodo2.
2013-04-01 21:38:45.012
[crsd(27291)]CRS-0810:Cluster Ready Service aborted due to failure to communicate with Event Management Service with error [1]. Details at (:CRSD00120:) in /u01/app/11.2.0/grid/log/nodo2/crsd/crsd.log.
2013-04-01 21:38:45.160
[ohasd(12338)]CRS-2765:Resource 'ora.crsd' has failed on server 'nodo2'.
2013-04-01 21:38:52.790
[crsd(28784)]CRS-1012:The OCR service started on node nodo2.
2013-04-01 21:43:12.378
[ctssd(13076)]CRS-2412:The Cluster Time Synchronization Service detects that the local time is significantly different from the mean cluster time. Details in /u01/app/11.2.0/grid/log/nodo2/ctssd/octssd.log.
2013-04-01 21:48:56.285
[crsd(28784)]CRS-0810:Cluster Ready Service aborted due to failure to communicate with Event Management Service with error [1]. Details at (:CRSD00120:) in /u01/app/11.2.0/grid/log/nodo2/crsd/crsd.log.
2013-04-01 21:48:56.435
[ohasd(12338)]CRS-2765:Resource 'ora.crsd' has failed on server 'nodo2'.
2013-04-01 21:49:04.421
[crsd(30272)]CRS-1012:The OCR service started on node nodo2.
2013-04-01 21:59:08.183
[crsd(30272)]CRS-0810:Cluster Ready Service aborted due to failure to communicate with Event Management Service with error [1]. Details at (:CRSD00120:) in /u01/app/11.2.0/grid/log/nodo2/crsd/crsd.log.
2013-04-01 21:59:08.318
[ohasd(12338)]CRS-2765:Resource 'ora.crsd' has failed on server 'nodo2'.
2013-04-01 21:59:15.860
[crsd(31772)]CRS-1012:The OCR service started on node nodo2.

Hi santysharma, thanks for the reply, i have two ethernet interfaces: eth0 (public network 192.168.1.0) and eth1 (private network 10.5.3.0), there is no device using that ip range, here's the output of route command:
(Sorry for the alignment, i tried to tab it but the editor trims it again)
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use Iface
default 192.168.1.1 0.0.0.0 UG 0 0 0 eth0
private * 255.255.255.0 U 0 0 0 eth1
link-local * 255.255.0.0 U 1002 0 0 eth0
link-local * 255.255.0.0 U 1003 0 0 eth1
public * 255.255.255.0 U 0 0 0 eth0
And the /etc/hosts file
127.0.0.1 localhost localhost.localdomain localhost4 localhost4.localdomain4
::1 localhost localhost.localdomain localhost6 localhost6.localdomain6
10.5.3.1 nodo1.cluster nodo1
10.5.3.2 nodo2.cluster nodo2
192.168.1.13 cluster-scan
192.168.1.14 nodo1-vip
192.168.1.15 nodo2-vip
And the ifconfig -a
eth0 Link encap:Ethernet HWaddr C8:3A:35:D9:C6:2B
inet addr:192.168.1.12 Bcast:192.168.1.255 Mask:255.255.255.0
inet6 addr: fe80::ca3a:35ff:fed9:c62b/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:34708 errors:0 dropped:18 overruns:0 frame:0
TX packets:24693 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:48545969 (46.2 MiB) TX bytes:1994381 (1.9 MiB)
eth1 Link encap:Ethernet HWaddr 00:0D:87:D0:A3:8E
inet addr:10.5.3.2 Bcast:10.5.3.255 Mask:255.255.255.0
inet6 addr: fe80::20d:87ff:fed0:a38e/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:44 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:5344 (5.2 KiB)
Interrupt:23 Base address:0x6000
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:20 errors:0 dropped:0 overruns:0 frame:0
TX packets:20 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:1320 (1.2 KiB) TX bytes:1320 (1.2 KiB)
Now that i'm thinking i've read somewhere that ipv6 was no supported...yet there's no relation with the 169.254.x.x ip range.

Error while installing Oracle 10g on CentOS 5.5

Hello,
I have been using the following url to install oracle 10g R2:
http://onaxer.com/blog/blog/tag/oracle-10g-r2-installtion-on-centos-5-5rhel/
I have copied the oracle 10g R2 linux version from windows to linux using FTP.
All the installer requirements have been met, but i'm getting the following error while running the installation:
[oracle@localhost database]$ ./runInstaller
Starting Oracle Universal Installer...
Checking installer requirements...
Checking operating system version: must be redhat-3, SuSE-9, redhat-4, UnitedLinux-1.0, asianux-1 or asianux-2
Passed
All installer requirements met.
Preparing to launch Oracle Universal Installer from /tmp/OraInstall2011-02-21_03-11-44PM. Please wait ...[oracle@localhost database]$ Exception in thread "main" java.lang.UnsatisfiedLinkError: /tmp/OraInstall2011-02-21_03-11-44PM/jre/1.4.2/lib/i386/libawt.so: libXtst.so.6: cannot open shared object file: No such file or directory
at java.lang.ClassLoader$NativeLibrary.load(Native Method)
at java.lang.ClassLoader.loadLibrary0(Unknown Source)
at java.lang.ClassLoader.loadLibrary(Unknown Source)
at java.lang.Runtime.loadLibrary0(Unknown Source)
at java.lang.System.loadLibrary(Unknown Source)
at sun.security.action.LoadLibraryAction.run(Unknown Source)
at java.security.AccessController.doPrivileged(Native Method)
at sun.awt.NativeLibLoader.loadLibraries(Unknown Source)
at sun.awt.DebugHelper.<clinit>(Unknown Source)
at java.awt.Component.<clinit>(Unknown Source)
Any help would be greatly appreciated.
Thanks.

Hi,
Download & Install the following rpm and retry oracle installation.
http://oss.oracle.com/projects/compat-oracle/dist/files/Enterprise_Linux/xorg-x11-libs-compat-6.8.2-1.EL.33.0.1.i386.rpm
installation
rpm -i xorg-x11-libs-compat-6.8.2-1.EL.33.0.1.i386.rpm
After the RPM, is installed, you will also need to override the /usr/lib/libXtst.so.6 with the one from /usr/X11R6/lib/libXtst.so.6.
As root, issue the commands:
mv /usr/lib/libXtst.so.6 /usr/lib/libXtst.so.6.ORG
ln –s /usr/X11R6/lib/libXtst.so.6 /usr/lib/libXtst.so.6
Pubudu

Root.sh fails on second node during clusterware installation

I am setting up a test instance of OEL 5.4 using VMware.
I am running the clusterware install and it is failing only on node2. See below.
I followed note 414897.1 on metalink for raw device setup.
Any help would be greatly appreciate.
2010-09-01 11:58:21.084: [ default][1275584]a_init:7!: Backend init unsuccessful : [22]
2010-09-01 11:58:21.091: [ OCRRAW][1275584]propriogid:1: INVALID FORMAT
2010-09-01 11:58:21.091: [ OCRRAW][1275584]ibctx:1:ERROR: INVALID FORMAT
2010-09-01 11:58:21.091: [ OCRRAW][1275584]proprinit:problem reading the bootblock or superbloc 22
2010-09-01 11:58:21.097: [ OCRRAW][1275584]propriogid:1: INVALID FORMAT
2010-09-01 11:58:21.139: [ OCRRAW][1275584]propriowv: Vote information on disk 0 [u01/app/oracle/oradata/ocr] is adjusted from [0/0] to [2/2]
2010-09-01 11:58:21.191: [ OCRRAW][1275584]propriniconfig:No 92 configuration
2010-09-01 11:58:21.192: [ OCRAPI][1275584]a_init:6a: Backend init successful
2010-09-01 11:58:21.299: [ OCRCONF][1275584]Initialized DATABASE keys in OCR
2010-09-01 11:58:21.555: [ OCRCONF][1275584]Successfully set skgfr block 0
2010-09-01 11:58:21.557: [ OCRCONF][1275584]Exiting [status=success]...

Oracle 10gR2 RAC Installation in RedHat 5 Linux Using VMware.
Important points to install 10gR2 oracle RAC in linux5.
1.LINUX 5(Redhat 5) doesn't have /etc/sysconfig/rawdevices file. so we have to configure it.
2. Edit the /etc/redhat-release version to redhat-4 and and to invoke the runInstaller use the command
$runInstaller -ignoreSysPrereqs. //this will bypass the os check //
3. Next during clusterware installation at the end of root.sh in node 2 end with error message.So we have adjust the parameters in vipca and srvctl files.
4. vipca will fail to run. so we have to adjust some parameters and configure it manually.
refer the link, it will be useful to you to complete your installation.
http://oracleinstance.blogspot.com/2010/03/oracle-10g-installation-in-linux-5.html

Root.sh failed in one node - CLSMON and UDLM

Hi experts.
My enviroment is:
2-node SunCluster Update3
Oracle RAC 10.2.0.1 > planning to upgrade to 10.2.0.4
The problem is: I installed the CRS services on 2 nodes - OK
After that, running root.sh fails in 1 node:
/u01/app/product/10/CRS/root.sh
WARNING: directory '/u01/app/product/10' is not owned by root
WARNING: directory '/u01/app/product' is not owned by root
WARNING: directory '/u01/app' is not owned by root
WARNING: directory '/u01' is not owned by root
Checking to see if Oracle CRS stack is already configured
Checking to see if any 9i GSD is up
Setting the permissions on OCR backup directory
Setting up NS directories
Oracle Cluster Registry configuration upgraded successfully
WARNING: directory '/u01/app/product/10' is not owned by root
WARNING: directory '/u01/app/product' is not owned by root
WARNING: directory '/u01/app' is not owned by root
WARNING: directory '/u01' is not owned by root
clscfg: EXISTING configuration version 3 detected.
clscfg: version 3 is 10G Release 2.
Successfully accumulated necessary OCR keys.
Using ports: CSS=49895 CRS=49896 EVMC=49898 and EVMR=49897.
node <nodenumber>: <nodename> <private interconnect name> <hostname>
node 0: spodhcsvr10 clusternode1-priv spodhcsvr10
node 1: spodhcsvr12 clusternode2-priv spodhcsvr12
clscfg: Arguments check out successfully.
NO KEYS WERE WRITTEN. Supply -force parameter to override.
-force is destructive and will destroy any previous cluster
configuration.
Oracle Cluster Registry for cluster has already been initialized
Sep 22 13:34:17 spodhcsvr10 root: Oracle Cluster Ready Services starting by user request.
Startup will be queued to init within 30 seconds.
Sep 22 13:34:20 spodhcsvr10 root: Cluster Ready Services completed waiting on dependencies.
Adding daemons to inittab
Expecting the CRS daemons to be up within 600 seconds.
Sep 22 13:34:34 spodhcsvr10 last message repeated 3 times
Sep 22 13:34:34 spodhcsvr10 root: Running CRSD with TZ = Brazil/East
Sep 22 13:34:40 spodhcsvr10 root: Oracle CLSMON terminated with unexpected status 10. Respawning
Sep 22 13:35:43 spodhcsvr10 last message repeated 9 times
Sep 22 13:36:07 spodhcsvr10 root: Cluster Ready Services completed waiting on dependencies.
Sep 22 13:36:07 spodhcsvr10 root: Running CRSD with TZ = Brazil/East
Sep 22 13:36:14 spodhcsvr10 su: libsldap: Status: 85 Mesg: openConnection: simple bind failed - Timed out
Sep 22 13:36:19 spodhcsvr10 root: Oracle CLSMON terminated with unexpected status 10. Respawning
Sep 22 13:37:35 spodhcsvr10 last message repeated 11 times
Sep 22 13:37:40 spodhcsvr10 root: Cluster Ready Services completed waiting on dependencies.
Sep 22 13:37:40 spodhcsvr10 root: Running CRSD with TZ = Brazil/East
Sep 22 13:37:42 spodhcsvr10 root: Oracle CLSMON terminated with unexpected status 10. Respawning
Sep 22 13:38:03 spodhcsvr10 last message repeated 3 times
Sep 22 13:38:10 spodhcsvr10 root: Oracle CLSMON terminated with unexpected status 10. Respawning
Sep 22 13:39:12 spodhcsvr10 last message repeated 9 times
Sep 22 13:39:13 spodhcsvr10 root: Cluster Ready Services completed waiting on dependencies.
Sep 22 13:39:13 spodhcsvr10 root: Running CRSD with TZ = Brazil/East
Sep 22 13:39:19 spodhcsvr10 root: Oracle CLSMON terminated with unexpected status 10. Respawning
Sep 22 13:40:42 spodhcsvr10 last message repeated 12 times
Sep 22 13:40:46 spodhcsvr10 root: Cluster Ready Services completed waiting on dependencies.
Sep 22 13:40:46 spodhcsvr10 root: Running CRSD with TZ = Brazil/East
Sep 22 13:40:49 spodhcsvr10 root: Oracle CLSMON terminated with unexpected status 10. Respawning
Sep 22 13:42:05 spodhcsvr10 last message repeated 11 times
Sep 22 13:42:11 spodhcsvr10 root: Cluster Ready Services completed waiting on dependencies.
Sep 22 13:42:12 spodhcsvr10 root: Oracle CLSMON terminated with unexpected status 10. Respawning
Sep 22 13:42:19 spodhcsvr10 root: Cluster Ready Services completed waiting on dependencies.
Sep 22 13:42:19 spodhcsvr10 root: Running CRSD with TZ = Brazil/East
Sep 22 13:42:19 spodhcsvr10 root: Oracle CLSMON terminated with unexpected status 10. Respawning
Sep 22 13:43:49 spodhcsvr10 last message repeated 13 times
Sep 22 13:43:51 spodhcsvr10 root: Cluster Ready Services completed waiting on dependencies.
Sep 22 13:43:51 spodhcsvr10 root: Running CRSD with TZ = Brazil/East
Sep 22 13:43:56 spodhcsvr10 root: Oracle CLSMON terminated with unexpected status 10. Respawning
Failure at final check of Oracle CRS stack.
I traced the ocssd.log and found some informations:
[    CSSD]2010-09-22 14:04:14.739 [6] >TRACE: clssnmDiskStateChange: state from 2 to 4 disk (0//dev/vx/rdsk/racdg/ora_vote1)
[    CSSD]2010-09-22 14:04:14.742 [6] >TRACE: clssnmReadDskHeartbeat: node(1) is down. rcfg(2) wrtcnt(2478) LATS(0) Disk lastSeqNo(2478)
[    CSSD]2010-09-22 14:04:14.742 [7] >TRACE: clssnmDiskStateChange: state from 2 to 4 disk (1//dev/vx/rdsk/racdg/ora_vote2)
[    CSSD]2010-09-22 14:04:14.744 [7] >TRACE: clssnmReadDskHeartbeat: node(1) is down. rcfg(2) wrtcnt(2478) LATS(0) Disk lastSeqNo(2478)
[    CSSD]2010-09-22 14:04:14.745 [8] >TRACE: clssnmDiskStateChange: state from 2 to 4 disk (2//dev/vx/rdsk/racdg/ora_vote3)
[    CSSD]2010-09-22 14:04:14.746 [8] >TRACE: clssnmReadDskHeartbeat: node(1) is down. rcfg(2) wrtcnt(2478) LATS(0) Disk lastSeqNo(2478)
[    CSSD]2010-09-22 14:04:14.785 [1] >TRACE: clssscSclsFatal: read value of disable
[    CSSD]2010-09-22 14:04:14.785 [10] >TRACE: clssnmFatalThread: spawned
[    CSSD]2010-09-22 14:04:14.785 [1] >TRACE: clssscSclsFatal: read value of disable
[    CSSD]2010-09-22 14:04:14.786 [11] >TRACE: clssnmconnect: connecting to node 0, flags 0x0001, connector 1
[    CSSD]2010-09-22 14:04:23.075 >USER: Oracle Database 10g CSS Release 10.2.0.1.0 Production Copyright 1996, 2004 Oracle. All rights reserved.
[    CSSD]2010-09-22 14:04:23.075 >USER: CSS daemon log for node spodhcsvr10, number 0, in cluster NET_RAC
[ clsdmt]Listening to (ADDRESS=(PROTOCOL=ipc)(KEY=spodhcsvr10DBG_CSSD))
[    CSSD]2010-09-22 14:04:23.082 [1] >TRACE: clssscmain: local-only set to false
[    CSSD]2010-09-22 14:04:23.096 [1] >TRACE: clssnmReadNodeInfo: added node 0 (spodhcsvr10) to cluster
[    CSSD]2010-09-22 14:04:23.106 [1] >TRACE: clssnmReadNodeInfo: added node 1 (spodhcsvr12) to cluster
[    CSSD]2010-09-22 14:04:23.129 [5] >TRACE: [0]Node monitor: dlm attach failed error LK_STAT_NOTCREATED
[    CSSD]CLSS-0001: skgxn not active
[    CSSD]2010-09-22 14:04:23.129 [5] >TRACE: clssnm_skgxnmon: skgxn init failed, rc 30
[    CSSD]2010-09-22 14:04:23.132 [1] >TRACE: clssnmInitNMInfo: misscount set to 600
[    CSSD]2010-09-22 14:04:23.136 [1] >TRACE: clssnmDiskStateChange: state from 1 to 2 disk (0//dev/vx/rdsk/racdg/ora_vote1)
[    CSSD]2010-09-22 14:04:23.139 [1] >TRACE: clssnmDiskStateChange: state from 1 to 2 disk (1//dev/vx/rdsk/racdg/ora_vote2)
[    CSSD]2010-09-22 14:04:23.143 [1] >TRACE: clssnmDiskStateChange: state from 1 to 2 disk (2//dev/vx/rdsk/racdg/ora_vote3)
[    CSSD]2010-09-22 14:04:25.139 [6] >TRACE: clssnmDiskStateChange: state from 2 to 4 disk (0//dev/vx/rdsk/racdg/ora_vote1)
[    CSSD]2010-09-22 14:04:25.142 [6] >TRACE: clssnmReadDskHeartbeat: node(1) is down. rcfg(2) wrtcnt(2488) LATS(0) Disk lastSeqNo(2488)
[    CSSD]2010-09-22 14:04:25.143 [7] >TRACE: clssnmDiskStateChange: state from 2 to 4 disk (1//dev/vx/rdsk/racdg/ora_vote2)
[    CSSD]2010-09-22 14:04:25.144 [7] >TRACE: clssnmReadDskHeartbeat: node(1) is down. rcfg(2) wrtcnt(2488) LATS(0) Disk lastSeqNo(2488)
[    CSSD]2010-09-22 14:04:25.145 [8] >TRACE: clssnmDiskStateChange: state from 2 to 4 disk (2//dev/vx/rdsk/racdg/ora_vote3)
[    CSSD]2010-09-22 14:04:25.148 [8] >TRACE: clssnmReadDskHeartbeat: node(1) is down. rcfg(2) wrtcnt(2489) LATS(0) Disk lastSeqNo(2489)
[    CSSD]2010-09-22 14:04:25.186 [1] >TRACE: clssscSclsFatal: read value of disable
[    CSSD]2010-09-22 14:04:25.186 [10] >TRACE: clssnmFatalThread: spawned
[    CSSD]2010-09-22 14:04:25.186 [1] >TRACE: clssscSclsFatal: read value of disable
[    CSSD]2010-09-22 14:04:25.187 [11] >TRACE: clssnmconnect: connecting to node 0, flags 0x0001, connector 1
[    CSSD]2010-09-22 14:04:33.449 >USER: Oracle Database 10g CSS Release 10.2.0.1.0 Production Copyright 1996, 2004 Oracle. All rights reserved.
[    CSSD]2010-09-22 14:04:33.449 >USER: CSS daemon log for node spodhcsvr10, number 0, in cluster NET_RAC
[ clsdmt]Listening to (ADDRESS=(PROTOCOL=ipc)(KEY=spodhcsvr10DBG_CSSD))
[    CSSD]2010-09-22 14:04:33.457 [1] >TRACE: clssscmain: local-only set to false
[    CSSD]2010-09-22 14:04:33.470 [1] >TRACE: clssnmReadNodeInfo: added node 0 (spodhcsvr10) to cluster
[    CSSD]2010-09-22 14:04:33.480 [1] >TRACE: clssnmReadNodeInfo: added node 1 (spodhcsvr12) to cluster
[    CSSD]2010-09-22 14:04:33.498 [5] >TRACE: [0]Node monitor: dlm attach failed error LK_STAT_NOTCREATED
[    CSSD]CLSS-0001: skgxn not active
[    CSSD]2010-09-22 14:04:33.498 [5] >TRACE: clssnm_skgxnmon: skgxn init failed, rc 30
[    CSSD]2010-09-22 14:04:33.500 [1] >TRACE: clssnmInitNMInfo: misscount set to 600
[    CSSD]2010-09-22 14:04:33.505 [1] >TRACE: clssnmDiskStateChange: state from 1 to 2 disk (0//dev/vx/rdsk/racdg/ora_vote1)
[    CSSD]2010-09-22 14:04:33.508 [1] >TRACE: clssnmDiskStateChange: state from 1 to 2 disk (1//dev/vx/rdsk/racdg/ora_vote2)
[    CSSD]2010-09-22 14:04:33.510 [1] >TRACE: clssnmDiskStateChange: state from 1 to 2 disk (2//dev/vx/rdsk/racdg/ora_vote3)
[    CSSD]2010-09-22 14:04:35.508 [6] >TRACE: clssnmDiskStateChange: state from 2 to 4 disk (0//dev/vx/rdsk/racdg/ora_vote1)
[    CSSD]2010-09-22 14:04:35.510 [6] >TRACE: clssnmReadDskHeartbeat: node(1) is down. rcfg(2) wrtcnt(2499) LATS(0) Disk lastSeqNo(2499)
[    CSSD]2010-09-22 14:04:35.510 [7] >TRACE: clssnmDiskStateChange: state from 2 to 4 disk (1//dev/vx/rdsk/racdg/ora_vote2)
[    CSSD]2010-09-22 14:04:35.512 [7] >TRACE: clssnmReadDskHeartbeat: node(1) is down. rcfg(2) wrtcnt(2499) LATS(0) Disk lastSeqNo(2499)
[    CSSD]2010-09-22 14:04:35.513 [8] >TRACE: clssnmDiskStateChange: state from 2 to 4 disk (2//dev/vx/rdsk/racdg/ora_vote3)
[    CSSD]2010-09-22 14:04:35.514 [8] >TRACE: clssnmReadDskHeartbeat: node(1) is down. rcfg(2) wrtcnt(2499) LATS(0) Disk lastSeqNo(2499)
[    CSSD]2010-09-22 14:04:35.553 [1] >TRACE: clssscSclsFatal: read value of disable
[    CSSD]2010-09-22 14:04:35.553 [10] >TRACE: clssnmFatalThread: spawned
[    CSSD]2010-09-22 14:04:35.553 [1] >TRACE: clssscSclsFatal: read value of disable
[    CSSD]2010-09-22 14:04:35.553 [11] >TRACE: clssnmconnect: connecting to node 0, flags 0x0001, connector 1
I believe the main error is:
[    CSSD]2010-09-22 14:04:33.498 [5] >TRACE: [0]Node monitor: dlm attach failed error LK_STAT_NOTCREATED
[    CSSD]CLSS-0001: skgxn not active
And the communication between UDLM and CLSMON. But i don't know how to resolve this.
My UDLM version is 3.3.4.9.
Somebody have any ideas about this?
Tks!

Now i finally installed CRS and run root.sh without errors (i think that problem is in some old file from other instalation tries...)
But now i have another problem: When install DB software, in step to copy instalation to remote node, this node have some failure in CLSMON/CSSD daemon and panicking:
Sep 23 16:10:51 spodhcsvr10 root: Oracle CLSMON terminated with unexpected status 138. Respawning
Sep 23 16:10:52 spodhcsvr10 root: Oracle CSSD failure. Rebooting for cluster integrity.
Sep 23 16:10:52 spodhcsvr10 root: [ID 702911 user.alert] Oracle CSSD failure. Rebooting for cluster integrity.
Sep 23 16:10:51 spodhcsvr10 root: [ID 702911 user.error] Oracle CLSMON terminated with unexpected status 138. Respawning
Sep 23 16:10:52 spodhcsvr10 root: [ID 702911 user.alert] Oracle CSSD failure. Rebooting for cluster integrity.
Sep 23 16:10:56 spodhcsvr10 Cluster.OPS.UCMMD: fatal: received signal 15
Sep 23 16:10:56 spodhcsvr10 Cluster.OPS.UCMMD: [ID 770355 daemon.error] fatal: received signal 15
Sep 23 16:10:59 spodhcsvr10 root: Oracle Cluster Ready Services waiting for SunCluster and UDLM to start.
Sep 23 16:10:59 spodhcsvr10 root: Cluster Ready Services completed waiting on dependencies.
Sep 23 16:10:59 spodhcsvr10 root: [ID 702911 user.error] Oracle Cluster Ready Services waiting for SunCluster and UDLM to start.
Sep 23 16:10:59 spodhcsvr10 root: [ID 702911 user.error] Cluster Ready Services completed waiting on dependencies.
Notifying cluster that this node is panicking
The instalation in first node continue and report error in copy to second node.
Any ideas? Tks!

Root.sh fails on 2nd node

AIX 6
Oracle grid infrastructure 11.2.0.3
At the end of the grid install, ran the root.sh on the first node then on the second node, but failed on the second node. Ran deconfig was successfull, but root.sh failed again :
The deconfig worked but not the root.sh:
Successfully deconfigured Oracle clusterware stack on this node
mtnx213:/oracle/app/grid/product/11.2.0/grid/crs/install#/oracle/app/grid/product/11.2.0/grid/root.sh
Performing root user operation for Oracle 11g
The following environment variables are set as:
ORACLE_OWNER= oragrid
ORACLE_HOME= /oracle/app/grid/product/11.2.0/grid
Enter the full pathname of the local bin directory: [/usr/local/bin]:
The contents of "dbhome" have not changed. No need to overwrite.
The contents of "oraenv" have not changed. No need to overwrite.
The contents of "coraenv" have not changed. No need to overwrite.
Entries will be added to the /etc/oratab file as needed by
Database Configuration Assistant when a database is created
Finished running generic part of root script.
Now product-specific root actions will be performed.
Using configuration parameter file: /oracle/app/grid/product/11.2.0/grid/crs/install/crsconfig_params
User ignored Prerequisites during installation
User oragrid has the required capabilities to run CSSD in realtime mode
OLR initialization - successful
Adding Clusterware entries to inittab
USM driver install actions failed
/oracle/app/grid/product/11.2.0/grid/perl/bin/perl -I/oracle/app/grid/product/11.2.0/grid/perl/lib -I/oracle/app/grid/product/11.2.0/grid/crs/install /oracle/app/grid/product/11.2.0/grid/crs/install/rootcrs.pl execution failed

My answer you can find here (in your duplicate post): root.sh fails on 2nd node Timed out waiting for the CRS stack to start

Error while installing Oracle 10g on Fedora Core 1

Error while installing Oracle 10g on Fedora Core 1. After 40% of the Installation is thru, the progress bar is showing 40%, it gives error "Not connected to Oracle" and the installation has to be terminated.
We have tried by using the on-line procedure and changing the required script to make believe it as said.

Are you createing DB also???

"Error In Writing to directory ..." getting the error while installing oracle 10g in laptop

Hi
I thought I'd make my first post a hijack of a vaguely related thread,
then some kind moderator could separate it out and branch it off to a post of its own.
I'm not even sure this is in the proper forum.
But anyhow ...
i am getting problem while installing oracle 10g in laptop its showing error as "Error in Writing to Directory C:\Users\Accent.Muthu\Appdata\Local\temp\OraInstall2011-03-03-10-51-53 AM.
Please ensure that the directory is writable and has atleast of 45 MB of disk space.Installation can not continue.
so please tell me the solution as soon as possible
thanks,
arshad ayub

Try the few resolutions mentioned here -
forms 10g installation error in writing to directory
Specially -
do not try to install from directory which has a space in its path
TMP and TEMP environment variables are set correctly, preferably to C:/tempRegards,
Anuj

Error while installing developer 10g on linux suse 10.0

Hi All,
This error appears while installing developer 10g on linux suse 10.0
http://img179.imageshack.us/my.php?image=errorso9.png

Try locate (using find command for example) the libjvm.so file (I assume that is located somewhere under $ORACLE_HOME (probably jdk or jre directory)). If you locate the path where this library resides, try to add that path to $LD_LIBRARY_PATH enviroment variable.
Use copy&paste method (for error message) rather than link to image.
It is much quicker operation and it may help to other people because they be able to find this thread via search engine.

Error while installing oracle 10g on AIX

I am receiving the following error while installing oracle 10g on AIX..
error in invoking target 'relink' of makefile 'u01/app/oracle/product/10.2.0/orcl/precomp/lib/ins_precomp.mk'..
i am installing enterprise edition. pl help

Hi;
What is AIX version?
Please see:
Installing 10g On Aix 5.3:'Error In Invoking Target 'Relink' Of Makefile ...' [ID 309668.1]
AIX: On Silent Install, Getting Several 'Error In Invoking Target' Messages [ID 351380.1]
"Error invoking target ... of makefile ... " Errors While Installing 8.1.6 [ID 113781.1]
Please also check below and be sure you have all prereq. on your server:
Oracle Database on Unix AIX,HP-UX,Linux,Mac OS X,Solaris,Tru64 Unix Operating Systems Installation and Configuration Requirements Quick Reference (8.0.5 to 11.2) [ID 169706.1]
Regard
Helios

An issue while installing oracle 10g express edition on Ubuntu 10.04-64bit

Hi,
I'm running into an issue while installing oracle 10g express edition on my Ubuntu 10.04-64 bit installed machine using oracle-xe-universal_10.2.0.1-1.0_i386.deb package. The issue actually came up when I was trying to reinstall the package after uninstalling it due to some problem I had with my login credentials. To elaborate further on it, the /etc/init.d/oracle-xe script does not get created when I execute the debian package and thus i'm unable to configure the required credentials and stuff after the installation. I doubt whether this has something to do with the procedure I followed when uninstalling the previous package it. But what I did was just what's mentioned in the following [http://download.oracle.com/docs/cd/B25329_01/doc/install.102/b25144/toc.htm] user guide published by oracle.
Another important clue would be, the platform of my machine is amd64bit although I'm dealing with an installation package preferred for i386. But I believe it's the only thing available in the oracle software download section. Hence I had to use the --force-architecture option to install it. But after reading some post published on this forum, I've figured out that it does not affect the usual execution of the software. Anyway, I would greatly appreciate some help on this matter.
[1] http://download.oracle.com/docs/cd/B25329_01/doc/install.102/b25144/toc.htm
Thanks and Regards,
Prabath Abeysekara
Edited by: 829281 on Jan 18, 2011 7:52 PM

Hi,
Finally I've managed to find a solution for this issue. Thanks a lot for all the replies.
Here's how I got rid of it.
Addressing all the facts one by one,
1.The problem of not getting the /etc/init.d/oracle-xe script generated was avoided
by removing all the configuration files that were previously created while installing
the product. The following command can be used to accomplish that task.
*$ dpkg --purge oracle-xe*
2.Next, Initially the password I used during the configuration process was "admin".
Although I tried a couple of times installing the product providing the aforementioned
password, the web UI kept prompting "Invalid Credentials" message not allowing me
to login. But, this particular issue could be avoided by giving some other simple
password.
Finally, got it working and once again thanks a bunch for taking the burden of
replying this thread.
Cheers,
Prabath

This problem appears while installing oracle 10g on enterprise linux

Hi All,
While installing oracle 10g on enterprise linux 5 this message apear:
http://img134.imageshack.us/my.php?image=problemqy2.png
More Info:
Oracle 10g supports redhat 4 and Enterprise Linux is redhat 5 so I changed the redhat-release to 4 to countinue setup but the above error appears, also I tried this configuration on SuSE 10 I changed the SuSE-release to 9 and went good.

The packeges are already installedIf you execute runInstaller again is the error message the same as before?
If yes can you post output for this command?
rpm -qa --qf '%{name}-%{version}-%{release}.%{arch}\n'|grep -i 'libxp'

11gR2 RAC install fail when running root.sh script on second node

I get the errors:
ORA-15018: diskgroup cannot be created
ORA-15072: command requires at least 2 regular failure groups, discovered only 0
ORA-15080: synchronous I/O operation to a disk failed
[main] [ 2012-04-10 16:44:12.564 EDT ] [UsmcaLogger.logException:175] oracle.sysman.assistants.util.sqlEngine.SQLFatalErrorException: ORA-15018: diskgroup cannot be created
ORA-15072: command requires at least 2 regular failure groups, discovered only 0
ORA-15080: synchronous I/O operation to a disk failed
I have tried the fix solutions from metalink note, but did not fix issue
11GR2 GRID INFRASTRUCTURE INSTALLATION FAILS WHEN RUNNING ROOT.SH ON NODE 2 OF RAC USING ASMLIB [ID 1059847.1

Hi,
it looks like, that your "shared device" you are using is not really shared.
The second node does "create an ASM diskgroup" and create OCR and Voting disks. If this indeed would be a shared device, he should have recognized, that your disk is shared.
So as a result your VMware configuration must be wrong, and the disk you presented as shared disk is not really shared.
Which VMWare version did you use? It will not work correctly with the workstation or player edition, since shared disks are only really working with the server version.
If you indeed using the server, could you paste your vm configurations?
Furthermore I recommend using Virtual Box. There is a nice how-to:
http://www.oracle-base.com/articles/11g/OracleDB11gR2RACInstallationOnOEL5UsingVirtualBox.php
Sebastian

Root.sh failed on second node while installing CRS 10g on centos 5.5

Similar Messages

Maybe you are looking for