Router activity does not evaluate conditions cases.
Hi all,
I have a bounded taskflow as a region in a jspx page. This task flow has 3 activity. The default one is a router that evaluate two cases, and navigate to one page fragment. The two cases expressions are like this :
<router id="router1">
<case>
<expression>#{data.somePageDef.someIterator.estimatedRowCount > 0}</expression>
<outcome>initManyLines</outcome>
</case>
<case>
<expression>#{data.somePageDef.someIterator.estimatedRowCount == 0}</expression>
<outcome>initZeroLines</outcome>
</case>
<default-outcome>initZeroLines</default-outcome>
</router>So depending of the number of lines in the someiterator iterator, it navigate to one of the two pages. But that does not work. It always redirect to the default outcome.
The somePageDef pageDef is bound to the jspx that encapsulate the region.
Any ideas ?
Regards
Fred
Ok I solved myself.
I used an input parameter that is set to iterator.estimatedRowCount in the parent pageDef, and the router use it in the task flow via #{pageflowScope.myStuff}, and navigate.
fred
Similar Messages
-
Wait activity does not expires after giving time frame
Hi all,
We are using SOA suite version 11.1.1.5. In our process, we use a wait activity so that the process will wait for a certain time frame (say 1 min) and again proceeds when the wait activity time expires.
The above process was running successfully for some months. But suddenly the instances are getting stopped in the wait activity and they are not proceeding after the given time.
The audit trail shows wait activity pending. And the wait activity does not expires even after the respected time.
Kindly suggest the possibilities of this scenario.
Regards,
GopiHi Gopi,
You can look at the logs to see if there are for any errors/warnings during the wait activity execution.
A possible explanation can be due to an error in a later on activity (like invoke or assign). If you have an error that you didn't catch, the process will try to rollback to the last dehydrate point (in your case the wait activity) and stuck there.
Thanks
Arik -
NGS Sponsors authentication does not work in case user has non-English character in his password
Hi,
we are using the NAC Guest Server v 2.0.1 and have Sponsors authentication done through Radius servers. Radius servers are Microsoft IAS using AD.
Sponsors user authentication works okay in case user's password includes English characters, but does not work in case an user uses national characters like for example Umlauts in German.
On Radius server I can see these error messages:
User XXXX was denied access.
Reason = Authentication was not successful because an unknown user name or incorrect password was used.
As soon as an user changes his password and uses English characters only, it resolves.
I guess this might be that NGS uses different coding while sending a password to Radius server, but not sure.
Appreciate if anyone knows a root cause and what could be a workaround. Unfortunately our AD policy allows users to use national characters and we can hardly change it. So a change on NGS or Radius side would be more viable.
Many thanks for your help.A case has been opened at Cisco and it is now quite clear that it is a problem with coding.
According to Cisco development team NGS uses UTF-8 coding to send the password, of course encrypted, to the Radius server. This cannot be changed within NGS. We use Radius Microsoft IAS Version 5.2.3790.3959 running on VMWare Windows 2003 SP2. More tests are scheduled to be performed. -
Xslt error: the expression does not evaluate to a node-set
hi guys - i'm really down because i cannot find / understand my xsl error and i have to finish my work very very soon
the error message (by using xalan to create from the xml file my html output) is the following:
xslt error: the expression does not evaluate to a node-set
and the code fragement is:
<xsl:template name="getNext">
<xsl:param name="currentKnoten" />
<xsl:for-each select="$currentKnoten"> //error is in this line
</xsl:for-each>
</xsl:template>please... help me....ok thanks!!! this saved me some time ;-)
now i go back to the origin problem... my main idea is the following xsl code... may u can see here the problem with the node site.. but i think u need the xml file or?
however this is my relevant xsl code:
<xsl:template match="DATA">
<xsl:element name="process">
<xsl:attribute name="name">
<xsl:value-of select="@name" />
</xsl:attribute>
<xsl:apply-templates select="INSTANCE"/>
</xsl:element>
</xsl:template>
<xsl:template match="INSTANCE[@class='Data']">
<xsl:element name="node">
<xsl:attribute name="name">
<xsl:value-of select="@name" />
</xsl:attribute>
<xsl:attribute name="class">
<xsl:value-of select="@class" />
</xsl:attribute>
<xsl:call-template name="copyAttributes" />
<xsl:variable name="nextNodes">
<xsl:value-of select="key('keyGetData', key('keyFrom', @name)/../TO/@instance)" />
</xsl:variable>
<xsl:call-template name="getNext">
<xsl:with-param name="currentNode" select="$nextNodes" />
</xsl:call-template>
</xsl:element>
</xsl:template>
<xsl:template name="getNext">
<xsl:param name="currentNode"/>
<xsl:for-each select="$currentNode">
<xsl:element name="node">
<xsl:attribute name="name"><xsl:value-of select="@name"/></xsl:attribute>
<xsl:attribute name="class"><xsl:value-of select="@class"/></xsl:attribute>
<xsl:variable name="nextNodes">
<xsl:value-of select="key('keyGetData', key('keyFrom', @name)/../TO/@instance)"/>
</xsl:variable>
<xsl:call-template name="copyAttributes"/>
<xsl:call-template name="getNext">
<xsl:with-param name="currentNode" select="$nextNodes"/>
</xsl:call-template>
</xsl:element>
</xsl:for-each>
</xsl:template>
<xsl:template name="copyAttributes">
<xsl:for-each select="descendant::*">
<xsl:copy>
<xsl:copy-of select="@*|node()"/>
</xsl:copy>
</xsl:for-each>
</xsl:template>
<xsl:template match="@*|node()">
<xsl:apply-templates/>
</xsl:template> -
you must have connected the Time Capsule with a router that does not work with my direct cable from my ISP
I tried to answer in your other post.. please stick to one thread ..
What method of internet do you have.. is this fibre install.. if so the TC should just plug in and use dhcp in router mode.. press and hold the reset and it will go back to router mode by default. -
HT2188 iPad 1 requested activation after being low on power. Activation does not work.
Hi
My iPad 1 requested activation after being low on power. Activation does not work so I have tried to restore it from iTunes. this progresses but after rebooting, it gets to the activation process for a few minutes and re-boots again - in a loop now. on ios6, not 7. help please?
I also looked at trying to do a manual install of firmware via iTunes but I do not know the version of firmware or how to find it out - so really stuck!
ThanksI pulled my unit out of the dock - powered up and the display goes blank (if you look carefully you can see the bios boot screen, then black, then you can see the backlight turn off.
I plugged in the USB monitor and boom - I could log in.
Once Logged in I could see that windows still thinks it has some of the monitors from the dock, and the internal display is set to disable.
So the issue is the detection / setup of monitors in/out of the dock.
I've done about all I can do for dubugging, I hope lenovo can pick up from here. if not I'll have to call lenovo support. -
Facing a problem while setting MAC 6.1. My version is 5.1. The activation does not complete.
Hacked or jailbroken iPhone will have this problem.
BTW, it's IOS 6.0.1 not MAC. -
I was CCNP but for sure a little bit too long to be efficient in routing. We received a new router (CISCO2901/K9) but I’m not able to use it.
Very easy scenario : 2 subnet : 1 WAN and 1 LAN.
Cisco router configuration :
version 15.2
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
hostname int-xxxxx
boot-start-marker
boot system flash0:c2900-universalk9_npe-mz.spa.152-4.m6a.bin
boot-end-marker
logging buffered 51200 warnings
no aaa new-model
memory-size iomem 10
ip domain name xxxxx.xxx
ip name-server 8.8.8.8
ip name-server 8.8.4.4
ip cef
no ipv6 cef
multilink bundle-name authenticated
crypto pki trustpoint TP-self-signed-13405798
enrollment selfsigned
subject-name cn=IOS-Self-Signed-Certificate-13405798
revocation-check none
crypto pki certificate chain TP-self-signed-13405798
certificate self-signed 01
3082024E 308201B7 A0030201 02020101 300D0609 2A864886 F70D0101 04050030
quit
license udi pid CISCO2901/K9 sn FTX180883V6
username cisco privilege 15 password 7 0822455D0A16
interface Embedded-Service-Engine0/0
no ip address
shutdown
interface GigabitEthernet0/0
ip address 62.119.117.65 255.255.255.224
duplex auto
speed auto
interface GigabitEthernet0/1
ip address 26.130.21.150 255.255.255.252
duplex full
speed 100
ip forward-protocol nd
no ip http server
ip http access-class 23
no ip http secure-server
ip route 0.0.0.0 0.0.0.0 26.130.21.149
ip route 62.119.117.96 255.255.255.224 62.119.117.66
access-list 23 permit X.X.X.X 0.0.0.255
access-list 23 permit X.X.X.X 0 0.0.0.255
snmp-server community XXXXXXXX RO 23
snmp-server enable traps entity-sensor threshold
control-plane
banner login ^CCCCCCCCCCCCCC
-- All logins are logged -- Private and restricted access --
-- Property of XXXXXX --
^C
line con 0
login local
line aux 0
line 2
no activation-character
no exec
transport preferred none
transport output pad telnet rlogin lapb-ta mop udptn v120 ssh
stopbits 1
line vty 0 4
access-class 23 in
privilege level 15
login local
transport input ssh
scheduler allocate 20000 1000
End
int-xxxx#sh ver
Cisco IOS Software, C2900 Software (C2900-UNIVERSALK9_NPE-M), Version 15.2(4)M6a, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2014 by Cisco Systems, Inc.
Compiled Tue 15-Apr-14 09:45 by prod_rel_team
ROM: System Bootstrap, Version 15.0(1r)M16, RELEASE SOFTWARE (fc1)
int-xxxx uptime is 3 hours, 31 minutes
System returned to ROM by reload at 21:08:06 UTC Fri Jun 27 2014
System image file is "flash0:c2900-universalk9_npe-mz.spa.152-4.m6a.bin"
Last reload type: Normal Reload
Last reload reason: Reload Command
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
Cisco CISCO2901/K9 (revision 1.0) with 475136K/49152K bytes of memory.
Processor board ID FTX180883V6
2 Gigabit Ethernet interfaces
1 terminal line
DRAM configuration is 64 bits wide with parity enabled.
255K bytes of non-volatile configuration memory.
250880K bytes of ATA System CompactFlash 0 (Read/Write)
License Info:
License UDI:
Device# PID SN
*0 CISCO2901/K9 XXXXXX
Technology Package License Information for Module:'c2900'
Technology Technology-package Technology-package
Current Type Next reboot
ipbase ipbasek9 Permanent ipbasek9
security None None None
uc None None None
data None None None
Configuration register is 0x2102
Desktop Configuration :
Ethernet adapter Ethernet:
Connection-specific DNS Suffix . :
IPv4 Address. . . . . . . . . . . : 62.119.117.71
Subnet Mask . . . . . . . . . . . : 255.255.255.224
Default Gateway . . . . . . . . . : 62.119.117.65
Issue Description :
I’m able to ping internet from my router :
int-xxxx#ping 8.8.8.8
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 8.8.8.8, timeout is 2 seconds:
From my desktop I’m able ton ping LAN and WAN interface of the router :
C:\Users\ars16537>ping 62.119.117.65
Pinging 62.119.117.65 with 32 bytes of data:
Reply from 62.119.117.65: bytes=32 time=1ms TTL=255
Reply from 62.119.117.65: bytes=32 time=1ms TTL=255
Reply from 62.119.117.65: bytes=32 time=1ms TTL=255
C:\Users\ars16537>ping 26.130.21.150
Pinging 26.130.21.150 with 32 bytes of data:
Reply from 26.130.21.150: bytes=32 time=1ms TTL=255
Reply from 26.130.21.150: bytes=32 time=1ms TTL=255
But not internet of the router next hop :
C:\Users\ars16537>ping 157.130.21.149
Pinging 26.130.21.149 with 32 bytes of data:
Request timed out.
Request timed out.
Request timed out.
Request timed out.
So the router doesn’t want routing. Any Idea ?Hi armandschindler,
I think you are missing something. make sure your lan interfaces are public ip. May be not, so your isp have no information about these routes 62.119.117.64 /27 eventually ping fail.
In this case you need nat on this router.
ping from your router is successful because Its public ip and your isp has information how to route back.
Regards,
kazim -
My router WRT54GX does not note the version.
I want to update my router as we are going to network and the router case does not note what version. The software is version 1.1. Does this mean that my unit is a v1?
If there is no any version number for your router then its a version 1 router.You could just logon to www.linksys.com/download & upgrade the firmware by clicking the Administration tab on the setup page.
-
Is this another MSI Flop.
Does anybody know if the HD led works when using SATA drives connected to the Via controller on the K8T Neo board?
I checked the case led and it works fine. It is not burnt out.
I also have the K7N2 Delta board and the HD led does not work on that board either when using SATA hard drives. I was told the led connecter was never wired to detect activity for the SATA drives only for IDE. A bios upgrade would never fix it.
I just setup K8T Neo and other than the HD Led not working the board seems to be pretty stable.The only led activity I get is when the board is first powered on and I just recently noticed when I play a DVD. The led seems to flicker when the dvd is playing.
Other than that I see no led activity with 1 or 2 SATA drives connected to the VIA controller.
Can someone confirm that it either works or it doesn't work.
I keep reading all these posts and some say it works and some say it don't.
Unless their is a new revision of the KT8 Neo and everybody is connecting their led to the HDD Led pins on JFP1 (Page 2-19 in the manual) they all should either work or they all should not workl. From what I gather their is no new revision of the board and only one Bios v1.1.
It also seems their was some confusion on what connector people were connecting thier led to on the motherboard. From what I read on page 2-19 in the manual thier is only one choice on JFP1 (Top row, pins 1 & 3). -
New router, printer does not work
A new wireless internet router and modem was installed yesterday. My printer does not respond from my MacBook Pro or my iPad. I followed all troubleshooting advice on HP and Apple websites. No luck. Apple support today suggested that my printer may need additional informatin which I cannot change. The Network ConfigurationCheck was perfect except for address changes and one other which may be significant. URLs for embedded web servers changed from http:/HP618550 to http://dhcppc2.
The Wireless Network Test Results were perfect. My computers acess the internet also without problems. Apple had me put a USB cable between the MacBook and the printer. Then the printer worked just fine. He thought (not being a printer guru) that perhaps the communication between the router and printer was the problem. Hence I come to this site. I have followed all HP site troubleshooting advice and met each criteria. HELP?After reading this through again, I am wondering if the router is unable to support Bonjour properly. Bonjour is the discovery service through which your Mac finds your printer on your network.
Although not for your identical router, this article may be helpful: http://h10025.www1.hp.com/ewfrf/wc/document?docname=c02986958&cc=us&dlc=en&lc=en#N135
If we can't get this resolved a for-sure, kill-it-dead solution is to get a normal, standard router (Linksys or Netgear) and put it in line with your ZyXel, disabling its wireless. I can help if you want to go this way. A good standard router would be $40 and you would be done.
Say thanks by clicking "Kudos" "thumbs up" in the post that helped you.
I am employed by HP -
Router webpage does not load correctly
I own a wireless WRT54G, which has worked fine in the past. After setting up a new wireless network, I went to the router webpage to open some ports. The problem with the page loading is that it doesn't display correctly. No clickable text is displayed on the top of the page or the side bar, so I basically can't do anything whatsoever to configure it. I've tried loading it up in both Firefox and Internet Explorer, with IE saying the page loaded but with errors. Any help would be much appreciated.
I did not understand what you meant when you said "After setting up a new wireless network". What new wireless network did you set up?
To view the router's web pages:
Use Internet Explorer, it usually works.
JavaScript must be enabled.
Use a computer that is wired to the router.
In the non-working computer, temporarily turn off your software firewall.
If you are using Zone Alarm, right click on the ZA icon in the system tray (lower right corner of screen) and then click "Shutdown ZoneAlarm", and see if this fixes your problem. If this does not work, try the following with Zone Alarm: Open the ZAISS control center, go to Privacy, then temporarily turn off Ad Blocking and Cookie Control, and see if that fixes your problem.
If you are using Noton Internet Security with the Add-on Pack, be sure to turn off the Pop-up Blocker. Some users have reported that they needed to uninstall the entire Norton Add-on Pack.
If you cannot get anything at 192.168.1.1 then perhaps this is not your router's address. Go to "Start" > All Programs > Accessories > Command Prompt.
A black DOS box will appear. Type in "ipconfig" (with no quotes), then hit the Enter key. Look at the "Default Gateway". Is it 192.168.1.1 ? Point your browser to the "Default Gateway", then login to your router.
If the above fails, disconnect your modem from the router, and try again. If this corrects your problem, then most likely you have a "modem-router" rather than an ordinary modem. Check to see if your "modem-router" is using the same 192.168.1.x address space as your Linksys router. If it is, then report back with this problem, and also state the make and model of your modem-router.
If all of the above fails, power down your entire system, unplug it from the wall, wait one minute, then power up and try again.
If all of the above tips fail, then reset the router to factory defaults: Power down the router and disconnect all wires from it. Wait one minute. Power up the router, allow it to fully boot (1-2 minutes), then press and hold the reset button for 30 seconds, then release the button and allow the router to reset and reboot ( 2-3 minutes). Power down router. Wait one minute. Connect one computer, by wire, to a LAN port on the router. Boot up system. It should work.
If the reset does not fix your system, then you need to download and install (or re-install) the latest firmware for your router. After the firmware upgrade, you must reset the router to factory defaults, then setup the router again from scratch. If you saved a router configuration file, DO NOT use it. -
"False" statement in case does not occur in case
Hi,
I've used the basic serial read/write to get some data from a microcontroller.
I had to modify the VI a bit, so I can check to see if the data I receive is either one specific value, or any other value.
My problem is that only the "true"-case occurs. If i receive anything else but '1', nothing happens.
Why does not the "false"-statement occur?
Regards,
Cato
Attachments:
Serial Write and Read1.vi 35 KBOh,
that LLB was written in LabVIEW 5.0
And those vi's cannot be opened in LabVIEW 8.5
I have put a note to the author of the KB Article, to update theLLB to a more compatible version
Meanwhile, here is the same LLB in LabVIEW 8.0
Sorry for the inconvenience
Attachments:
early version.PNG 8 KB
Comparison.llb 25 KB -
Router 7606 does not show the inventory for the Fan module
I have a issue with a router 7606, specifically with fan module, the LC go down because it does have sufficiently cooling , I changed the Fan module, the IOS, The power supply, and I still have the same issue, Besides the Router does not show the inventory or PID for module fan,
logg" system minor alarm on operating fan count"
Someone knows what could be happening,Check this:
Can you try this;
7606-01#show environment status fan-tray 1
fan-tray 1:
fan-tray 1 type: FAN-MOD-6SHS
fan-tray 1 mode: Auto
fan-tray 1 fan-fail: OK
7606-01#show power
Fan Type Watts A @42V State
1 FAN-MOD-6SHS 180.18 4.29 OK............................ FAn try
If above doesnt work then try the below link:
https://supportforums.cisco.com/discussion/10824271/7606-s-and-fan-module-6shs-version-1
HTH
inayath
*Plz dont forget to rate if this info is helpfull. -
Can't activate - activation does not have the required number of digits
I have an old paid version of CS that I have been using for years. I recently had my hard drive repaired and they managed to deactivate my CS. When I try and do the phone activation, after I enter the activation code it says "The number you entered does not have the required number of digits". I am reading it right off the screen in front of me. The only other info is activation type = repair. What are my options? I paid a lot for this and I would like to keep using it. Thanks for any help.
I am having the exact same problem. I have moved my Adobe CS3 to a new computer. Even though I am entering the activation code correctly as displayed on my screen, I still get the message "The number you entered does not have the required number of digits". You can then select to speak to someone, but then you receive a recording that Adobe is no longer handling activation problems via phone, goodbye, and I am disconnected.
How can I re-activate my CS3 product? I have a legitimate purchase and a legitimate license key. Thank you.
Maybe you are looking for
-
Third Party Order close if some quantity undeliver to Customer by vendor
Dear Friends In third Party Sales Process How to close the sales order 1. Customer Place Order = 10 pc 2. Purchase Order created = 10 Pc 3. Vendor Deliver the goods to customer = 8 Pc and MIGO and MIRO done on 8 Pc and Vendor unable to deliver remain
-
Please any assistance would be appreciated thanks. The Photo Downloader doesn't open up automatically but it did when CS6 was still on my system.
-
Download window is not working since update to 6.0?
I updated firefox and now the downloads window no longer functions. It appears on downloading a file. The file downloads but the window no longer shows the progress or the file.
-
Running Windows 7 64-bit Home Premium and noted the max ram could be 16 gb. Originally had 4 gb ram. Purchased PNY 8 gb (2x4 gb) DDR3 PC3-10666 ram. Tested one module with the orginal stock and received the memory error beep. Reset CMOS and still had
-
Transferring keyboard shortcuts between Mac and Windows
I need to migrate users from Mac (CS 5.5) to Windows 7 (CS 6). I have tried to transfer a user's custom keyboard shortcut set by copying the .indk file to the appropriate folder on the PC, and although it shows up in the list, when I try to select th