Routing from internal network to external (internet) - is this possible ?

Hi all,
I know that private IPs cannot be used on the internet. But what will be the component that is preventing it ?
In this setup below, assuming i am assigned a /24 public ip block, but i am not going to use or assigned them (e.g. NAT), how/where will my packet from host 1 to 8.8.8.8 be dropped ?
Regards
Noob

Disclaimer
The Author of this posting offers the information contained within this posting without consideration and with the reader's understanding that there's no implied or expressed suitability or fitness for any purpose. Information provided is for informational purposes only and should not be construed as rendering professional advice of any kind. Usage of this posting's information is solely at reader's own risk.
Liability Disclaimer
In no event shall Author be liable for any damages whatsoever (including, without limitation, damages for loss of use, data or profit) arising out of the use or inability to use the posting's information even if Author has been advised of the possibility of such damage.
Posting
Well, as Jon has already noted, packet is forwarded only by its destination IP.  Which means, if the original packet has only a private IP in its source address, it won't be involved in the forwarding decision.  (Again,  the source IP might still be subjected to analysis that will block the packet at some point.)
So, your private IP will only be a routing consideration if the receiving host is trying to reply and use your original source IP as the return packet's destinations IP.  (I suspect you understand the foregoing, but I did want to insure there's no misunderstanding.)
Ok, so if the original destination host generates a packet with a private IP for destination IP, it would be (most likely be) treated, from that host, like any other packet that host generates with a private IP in the destination.  I.e.  The network will attempt to deliver it.
If the prefix destination is totally unknown, the packet will be dropped unless the forwarding router has a default route (or aggregate) that covers it.
Assuming there's a local private subnet, that matches the destination, the network will deliver it to that network, and if there's a host with that actual private IP, the packet will be delivered to it.  Usually, the overlapping private IP host will drop the packet, as it won't have process expecting the packet, but it's possible, a process is might accept the packet and attempt to process it.  Then, most likely, the process will go "huh?" and drop the packet.  However, it's also possible the newly receiving host will reply to your original receiving host, i.e. those hosts will now fling packets back-and-forth, because of your original packet.  Again, this is all very unlikely normally, more so if the network isn't "sloppy", but such routing is the basis for some DDoS attacks. (For example, I place another host's IP in my packet's source IP, and then send out ping to the network broadcast IP.  Hosts receiving the ping will send a ping reply to the host I targeted.)

Similar Messages

  • HELP! How do I get rid of the volume noise that plays when I switch from internal speakers to external speakers?

    How do I get rid of the volume noise that plays when I switch from internal speakers to external speakers? I'm trying to watch something on my TV through an HDMi cable (& apple adapter) and when I go to switch the sound control in preferences from internal speakers to SONY TV, the annoying "popping" noise occurs on my TV's speakers.

    Go to Edit > Preferences > General > Import Settings and check the box for error correction, and then try one of the problem CDs again.

  • I recently lost my iphone 4 and have an iphone3 on loan until I get upgrade in Aug.  I want to sync my data - contacts most important  - from my itunes account...is this possible?  Is it possible to change the user ID on the borrowed phone to my ID?

    I recently lost my iphone 4 and have an iphone3 on loan until I get upgrade in Aug.  I want to sync my data - contacts most important  - from my itunes account...is this possible?  Is it possible to change the user ID on the borrowed phone to my ID?

    There are no contacts in itunes.
    Your contact should be on your computer in whatever program you have selected to sync.  Just sync them to the new one.
    Click Support at the top of this page, then click manuals
    Changing the itunes account on nthe iphone is covered there as is restoring the iphone as new or from backup.

  • I want to use my airport time capsule as a network attached storage solution, is this possible or do I need to connect a separate hard drive?

    I want to use my airport time capsule as a network attached storage solution, is this possible or do I need to connect it to a separate hard drive?

    The Time Capsule is by default a network hard drive, but it has no "brains" of it's own. So, it cannot function as a stand alone media server if that is what you are asking.
    If you are also using the Time Capsule hard drive for Time Machine backups of your Mac(s), then there may be struggle for available space on the drive since it is not possible to partition the Time Capsule drive in a traditional manner.
    If space is getting tight on the Time Capsule, it might be a good idea to connect a drive to the USB port on the Time Capsule and use that drive for your network storage needs.

  • I have a new macbook air, and want to transfer all my data using time machine from my old macbook running leopard, is this possible and easy

    I have a new macbook air, and want to transfer all my data using time machine from my old macbook running leopard, is this possible and easy and will it transfer all my musc and photos?

    The Setup Assistant can restore your data from a Time Machine backup. You'll be asked if you want to do this the first time you turn the computer on.
    (60797)

  • Routing and Remote access - internal network not accessing internet through public network!

    Hello,
    Good Evening to all.
    I got an issue in routing and remote access on windows 2003 server.  This server is already configured as File server, domain server and Application server. Also configured as router (through routing & remote access) for connecting three different
    network to each other. So This server has three NIC card installed and each NIC card represent separate network.
    three different network are - 192.42.160.0/24 , 192.42.161.0/24, 192.42.162.0/24
    Three NIC card installed on server as with following IP address -
    NIC -1 = 192.42.160.220 , Sub- 255.255.255.0 , Gateway - NO
    NIC -2 = 192.42.161.220 , Sub- 255.255.255.0 , Gateway - 192.161.220.112 (This ip for internet access so 4g router IP)
    NIC -3 = 192.42.162.220,  , Sub- 255.255.255.0 , Gateway - NO
    Now the issue is I can reach to internet & (also pinging to router ip 192.42.161.112) from only one network that is - 192.42.161.0/24 , BUT when I trying to access internet from another two network (192.42.160.0/24 & 192.42.162.0/24) I cant access
    it and moreover can't ping to internet router ip - 192.42.161.112...
    So how I can access to internet from other two network also? 
    I was already configured static routing for all three network but still I was not success. really I don't know what exactly static routing it should be done in routing & remote access so that all three network can reach to internet?
    Sorry if I am not able to explain properly. Please let me know if you need more explain on this...
    Thanks to all.

    Dear Milos,
    I am happy to hear from you....
    1.- Actually the setup was done long before by another guy and right now I don't want to change it. 
    Nice to hear from you! Thank you so much. Actually this is first time I am using technet forum upon the suggestion from one of the my friend. So any your help from you will help me a great in this issue...
    I ran the route print command and given follow are the results.
    I have only added the default route as per the below routes. Please guide me know how to add other static routes for three network.
    D:\Documents and Settings\Administrator>route print
    IPv4 Route Table
    ===========================================================================
    Interface List
    0x1 ........................... MS TCP Loopback interface
    0x2 ...00 30 05 ad 8f 5c ...... Broadcom NetXtreme Gigabit Ethernet - Teefer2 Mi
    niport
    0x3 ...00 0e 0c a7 c4 f8 ...... Intel(R) PRO/1000 GT Desktop Adapter - Teefer2 M
    iniport
    0x4 ...00 0e 0c a7 c5 85 ...... Intel(R) PRO/1000 GT Desktop Adapter #2 - Teefer
    2 Miniport
    ===========================================================================
    ===========================================================================
    Active Routes:
    Network Destination        Netmask          Gateway       Interface  Metric
              0.0.0.0          0.0.0.0   192.42.161.112   192.42.161.220      1
            127.0.0.0        255.0.0.0        127.0.0.1        127.0.0.1      1
         192.42.160.0    255.255.255.0   192.42.160.220   192.42.160.220     20
       192.42.160.220  255.255.255.255        127.0.0.1        127.0.0.1     20
       192.42.160.255  255.255.255.255   192.42.160.220   192.42.160.220     20
         192.42.161.0    255.255.255.0   192.42.161.220   192.42.161.220     20
       192.42.161.220  255.255.255.255        127.0.0.1        127.0.0.1     20
       192.42.161.255  255.255.255.255   192.42.161.220   192.42.161.220     20
         192.42.162.0    255.255.255.0   192.42.162.220   192.42.162.220     20
       192.42.162.220  255.255.255.255        127.0.0.1        127.0.0.1     20
       192.42.162.255  255.255.255.255   192.42.162.220   192.42.162.220     20
            224.0.0.0        240.0.0.0   192.42.160.220   192.42.160.220     20
            224.0.0.0        240.0.0.0   192.42.161.220   192.42.161.220     20
            224.0.0.0        240.0.0.0   192.42.162.220   192.42.162.220     20
      255.255.255.255  255.255.255.255   192.42.160.220   192.42.160.220      1
      255.255.255.255  255.255.255.255   192.42.161.220   192.42.161.220      1
      255.255.255.255  255.255.255.255   192.42.162.220   192.42.162.220      1
    Default Gateway:    192.42.161.112
    ===========================================================================
    Persistent Routes:
      None
    Regards & Thanks
    Mahesh

  • Cisco ASA 5505 Routing between internal networks

    Hi,
    I am new to Cisco ASA and have been configuring my new firewall but one thing have been bothering. I cannot get internal networks and routing between them to work as I would like to. Goal is to set four networks and control access with ACL:s between those.
    1. Outside
    2. DMZ
    3. ServerNet1
    4. Inside
    ASA version is 9.1 and i have been reading on two different ways on handling IP routing with this. NAT Exempt and not configuring NAT at all and letting normal IP routing to handle internal networks. No matter how I configure, with or without NAT I cannot get access from inside network to DMZ or from ServerNet1 to DMZ. Strange thing is that I can access services from DMZ to Inside and ServerNet1 if access list allows it. For instance DNS server is on Inside network and DMZ works great using it.
    Here is the running conf:
    interface Ethernet0/0
    switchport access vlan 20
    interface Ethernet0/1
    switchport access vlan 20
    interface Ethernet0/2
    switchport access vlan 19
    interface Ethernet0/3
    switchport access vlan 10
    switchport trunk allowed vlan 10,19-20
    switchport trunk native vlan 1
    interface Ethernet0/4
    switchport access vlan 10
    interface Ethernet0/5
    switchport access vlan 10
    switchport trunk allowed vlan 10-11,19-20
    switchport trunk native vlan 1
    switchport mode trunk
    interface Ethernet0/6
    switchport access vlan 10
    switchport trunk allowed vlan 10-11,19-20
    switchport trunk native vlan 1
    switchport mode trunk
    interface Ethernet0/7
    switchport access vlan 10
    interface Vlan10
    nameif inside
    security-level 90
    ip address 192.168.2.1 255.255.255.0
    interface Vlan11
    nameif ServerNet1
    security-level 100
    ip address 192.168.4.1 255.255.255.0
    interface Vlan19
    nameif DMZ
    security-level 10
    ip address 192.168.3.1 255.255.255.0
    interface Vlan20
    nameif outside
    security-level 0
    ip address dhcp setroute
    ftp mode passive
    clock timezone EEST 2
    clock summer-time EEDT recurring last Sun Mar 3:00 last Sun Oct 4:00
    object network obj_any
    subnet 0.0.0.0 0.0.0.0
    object network obj-192.168.2.0
    subnet 192.168.2.0 255.255.255.0
    object network obj-192.168.3.0
    subnet 192.168.3.0 255.255.255.0
    object network DNS
    host 192.168.2.10
    description DNS Liikenne
    object network Srv2
    host 192.168.2.10
    description DC, DNS, DNCP
    object network obj-192.168.4.0
    subnet 192.168.4.0 255.255.255.0
    object network ServerNet1
    subnet 192.168.4.0 255.255.255.0
    object-group protocol TCPUDP
    protocol-object udp
    protocol-object tcp
    object-group network RFC1918
    object-group network InternalNetworks
    network-object 192.168.2.0 255.255.255.0
    network-object 192.168.3.0 255.255.255.0
    object-group service DM_INLINE_SERVICE_1
    service-object tcp destination eq domain
    service-object udp destination eq domain
    service-object udp destination eq nameserver
    service-object udp destination eq ntp
    object-group service DM_INLINE_TCP_1 tcp
    port-object eq www
    port-object eq https
    port-object eq ftp
    port-object eq ftp-data
    object-group service rdp tcp-udp
    description Microsoft RDP
    port-object eq 3389
    object-group service DM_INLINE_TCP_2 tcp
    port-object eq ftp
    port-object eq ftp-data
    port-object eq www
    port-object eq https
    object-group service DM_INLINE_SERVICE_2
    service-object tcp destination eq domain
    service-object udp destination eq domain
    object-group network DM_INLINE_NETWORK_1
    network-object object obj-192.168.2.0
    network-object object obj-192.168.4.0
    access-list dmz_access_in extended permit ip object obj-192.168.3.0 object obj_any
    access-list dmz_access_in extended deny ip any object-group InternalNetworks
    access-list DMZ_access_in extended permit object-group TCPUDP object obj-192.168.3.0 object DNS eq domain
    access-list DMZ_access_in extended permit object-group TCPUDP object obj-192.168.3.0 object-group DM_INLINE_NETWORK_1 object-group rdp
    access-list DMZ_access_in extended deny ip any object-group InternalNetworks
    access-list DMZ_access_in extended permit tcp object obj-192.168.3.0 object obj_any object-group DM_INLINE_TCP_2
    access-list inside_access_in extended permit ip object obj-192.168.2.0 object-group InternalNetworks
    access-list inside_access_in extended permit object-group TCPUDP object obj-192.168.2.0 object obj_any object-group rdp
    access-list inside_access_in extended permit tcp object obj-192.168.2.0 object obj_any object-group DM_INLINE_TCP_1
    access-list inside_access_in extended permit object-group DM_INLINE_SERVICE_1 object Srv2 object obj_any
    access-list inside_access_in extended permit object-group TCPUDP object obj-192.168.2.0 object obj-192.168.3.0 object-group rdp
    access-list ServerNet1_access_in extended permit object-group DM_INLINE_SERVICE_2 any object DNS
    access-list ServerNet1_access_in extended permit ip any any
    pager lines 24
    logging enable
    logging asdm informational
    mtu ServerNet1 1500
    mtu inside 1500
    mtu DMZ 1500
    mtu outside 1500
    no failover
    icmp unreachable rate-limit 1 burst-size 1
    asdm image disk0:/asdm-711-52.bin
    no asdm history enable
    arp timeout 14400
    no arp permit-nonconnected
    nat (inside,DMZ) source static obj-192.168.2.0 obj-192.168.2.0 destination static obj-192.168.2.0 obj-192.168.2.0 no-proxy-arp
    object network obj_any
    nat (inside,outside) dynamic interface
    nat (DMZ,outside) after-auto source dynamic obj_any interface destination static obj_any obj_any
    nat (ServerNet1,outside) after-auto source dynamic obj-192.168.4.0 interface
    access-group ServerNet1_access_in in interface ServerNet1
    access-group inside_access_in in interface inside
    access-group DMZ_access_in in interface DMZ
    timeout xlate 3:00:00
    timeout pat-xlate 0:00:30
    timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
    timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
    timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
    timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
    timeout tcp-proxy-reassembly 0:01:00
    timeout floating-conn 0:00:00
    dynamic-access-policy-record DfltAccessPolicy
    user-identity default-domain LOCAL
    aaa authentication ssh console LOCAL
    http server enable
    http 192.168.2.0 255.255.255.0 inside
    http 192.168.4.0 255.255.255.0 ServerNet1
    no snmp-server location
    no snmp-server contact
    snmp-server enable traps snmp authentication linkup linkdown coldstart warmstart
    crypto ipsec security-association pmtu-aging infinite
    crypto ca trustpool policy
    telnet timeout 5
    ssh 192.168.4.0 255.255.255.0 ServerNet1
    ssh 192.168.2.0 255.255.255.0 inside
    ssh timeout 5
    console timeout 0
    dhcpd auto_config outside
    threat-detection basic-threat
    threat-detection statistics access-list
    no threat-detection statistics tcp-intercept
    class-map inspection_default
    match default-inspection-traffic
    policy-map type inspect dns preset_dns_map
    parameters
      message-length maximum client auto
      message-length maximum 512
    policy-map global_policy
    class inspection_default
      inspect dns preset_dns_map
      inspect ftp
      inspect h323 h225
      inspect h323 ras
      inspect rsh
      inspect rtsp
      inspect esmtp
      inspect sqlnet
      inspect skinny
      inspect sunrpc
      inspect xdmcp
      inspect sip
      inspect netbios
      inspect tftp
      inspect ip-options
      inspect icmp
    service-policy global_policy global
    prompt hostname context
    no call-home reporting anonymous

    Hi Jouni,
    Yep, Finnish would be good also =)
    In front of ASA is DSL modem, on the trunk ports is Hyper-V host that uses the trunk ports so that every VM has their VLAN ID defined in the VM level. Everything is working good on that end. Also there is WLAN Access Pois on one of the ASA ports, on the WLAN AP there is the management portal address on DMZ that i have been testing agains (192.168.3.4)
    If i configure Dynamic PAT from inside to the DMZ then the traffic starts to work from inside to all hosts on DMZ but thats not the right way to do it so no shortcuts =)
    Here is the conf now, still doesnt work:
    interface Ethernet0/0
    switchport access vlan 20
    interface Ethernet0/1
    switchport access vlan 20
    interface Ethernet0/2
    switchport access vlan 19
    interface Ethernet0/3
    switchport access vlan 10
    switchport trunk allowed vlan 10,19-20
    switchport trunk native vlan 1
    interface Ethernet0/4
    switchport access vlan 10
    interface Ethernet0/5
    switchport access vlan 10
    switchport trunk allowed vlan 10-11,19-20
    switchport trunk native vlan 1
    switchport mode trunk
    interface Ethernet0/6
    switchport access vlan 10
    switchport trunk allowed vlan 10-11,19-20
    switchport trunk native vlan 1
    switchport mode trunk
    interface Ethernet0/7
    switchport access vlan 10
    interface Vlan10
    nameif inside
    security-level 90
    ip address 192.168.2.1 255.255.255.0
    interface Vlan11
    nameif ServerNet1
    security-level 100
    ip address 192.168.4.1 255.255.255.0
    interface Vlan19
    nameif DMZ
    security-level 10
    ip address 192.168.3.1 255.255.255.0
    interface Vlan20
    nameif outside
    security-level 0
    ip address dhcp setroute
    ftp mode passive
    clock timezone EEST 2
    clock summer-time EEDT recurring last Sun Mar 3:00 last Sun Oct 4:00
    object network obj_any
    subnet 0.0.0.0 0.0.0.0
    object network obj-192.168.2.0
    subnet 192.168.2.0 255.255.255.0
    object network obj-192.168.3.0
    subnet 192.168.3.0 255.255.255.0
    object network DNS
    host 192.168.2.10
    description DNS Liikenne
    object network Srv2
    host 192.168.2.10
    description DC, DNS, DNCP
    object network obj-192.168.4.0
    subnet 192.168.4.0 255.255.255.0
    object network ServerNet1
    subnet 192.168.4.0 255.255.255.0
    object-group protocol TCPUDP
    protocol-object udp
    protocol-object tcp
    object-group network RFC1918
    object-group network InternalNetworks
    network-object 192.168.2.0 255.255.255.0
    network-object 192.168.3.0 255.255.255.0
    object-group service DM_INLINE_SERVICE_1
    service-object tcp destination eq domain
    service-object udp destination eq domain
    service-object udp destination eq nameserver
    service-object udp destination eq ntp
    object-group service DM_INLINE_TCP_1 tcp
    port-object eq www
    port-object eq https
    port-object eq ftp
    port-object eq ftp-data
    object-group service rdp tcp-udp
    description Microsoft RDP
    port-object eq 3389
    object-group service DM_INLINE_TCP_2 tcp
    port-object eq ftp
    port-object eq ftp-data
    port-object eq www
    port-object eq https
    object-group service DM_INLINE_SERVICE_2
    service-object tcp destination eq domain
    service-object udp destination eq domain
    object-group network DM_INLINE_NETWORK_1
    network-object object obj-192.168.2.0
    network-object object obj-192.168.4.0
    object-group network DEFAULT-PAT-SOURCE
    description Default PAT source networks
    network-object 192.168.2.0 255.255.255.0
    network-object 192.168.3.0 255.255.255.0
    network-object 192.168.4.0 255.255.255.0
    access-list dmz_access_in extended permit ip object obj-192.168.3.0 object obj_any
    access-list dmz_access_in extended deny ip any object-group InternalNetworks
    access-list DMZ_access_in extended permit object-group TCPUDP object obj-192.168.3.0 object DNS eq domain
    access-list DMZ_access_in extended permit object-group TCPUDP object obj-192.168.3.0 object-group DM_INLINE_NETWORK_1 object-group rdp
    access-list DMZ_access_in extended deny ip any object-group InternalNetworks
    access-list DMZ_access_in extended permit tcp object obj-192.168.3.0 object obj_any object-group DM_INLINE_TCP_2
    access-list inside_access_in extended permit ip object obj-192.168.2.0 object-group InternalNetworks
    access-list inside_access_in extended permit object-group TCPUDP object obj-192.168.2.0 object obj_any object-group rdp
    access-list inside_access_in extended permit tcp object obj-192.168.2.0 object obj_any object-group DM_INLINE_TCP_1
    access-list inside_access_in extended permit object-group DM_INLINE_SERVICE_1 object Srv2 object obj_any
    access-list inside_access_in extended permit object-group TCPUDP object obj-192.168.2.0 object obj-192.168.3.0 object-group rdp
    access-list ServerNet1_access_in extended permit object-group DM_INLINE_SERVICE_2 any object DNS
    access-list ServerNet1_access_in extended permit ip any any
    pager lines 24
    logging enable
    logging asdm informational
    mtu ServerNet1 1500
    mtu inside 1500
    mtu DMZ 1500
    mtu outside 1500
    no failover
    icmp unreachable rate-limit 1 burst-size 1
    asdm image disk0:/asdm-711-52.bin
    no asdm history enable
    arp timeout 14400
    no arp permit-nonconnected
    nat (any,outside) after-auto source dynamic DEFAULT-PAT-SOURCE interface
    access-group ServerNet1_access_in in interface ServerNet1
    access-group inside_access_in in interface inside
    access-group DMZ_access_in in interface DMZ
    timeout xlate 3:00:00
    timeout pat-xlate 0:00:30
    timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
    timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
    timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
    timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
    timeout tcp-proxy-reassembly 0:01:00
    timeout floating-conn 0:00:00
    dynamic-access-policy-record DfltAccessPolicy
    user-identity default-domain LOCAL
    aaa authentication ssh console LOCAL
    http server enable
    http 192.168.2.0 255.255.255.0 inside
    http 192.168.4.0 255.255.255.0 ServerNet1
    no snmp-server location
    no snmp-server contact
    snmp-server enable traps snmp authentication linkup linkdown coldstart warmstart
    crypto ipsec security-association pmtu-aging infinite
    crypto ca trustpool policy
    telnet timeout 5
    ssh 192.168.4.0 255.255.255.0 ServerNet1
    ssh 192.168.2.0 255.255.255.0 inside
    ssh timeout 5
    console timeout 0
    dhcpd auto_config outside
    threat-detection basic-threat
    threat-detection statistics access-list
    no threat-detection statistics tcp-intercept
    class-map inspection_default
    match default-inspection-traffic
    policy-map type inspect dns preset_dns_map
    parameters
      message-length maximum client auto
      message-length maximum 512
    policy-map global_policy
    class inspection_default
      inspect dns preset_dns_map
      inspect ftp
      inspect h323 h225
      inspect h323 ras
      inspect rsh
      inspect rtsp
      inspect esmtp
      inspect sqlnet
      inspect skinny
      inspect sunrpc
      inspect xdmcp
      inspect sip
      inspect netbios
      inspect tftp
      inspect ip-options
      inspect icmp
    service-policy global_policy global
    prompt hostname context
    no call-home reporting anonymous

  • As a new user of photoshop elements 11 I am trying to burn a few photos from the organiser to a cd is this possible and if so how is it achieved please?

    How do I burn a few of my photos to a cd from Photoshop Elements 11 organiser?

    Try this:
    How can we burn Photographs and other media files on a CD/DVD in PSE9? | Adobe Photoshop Elements

  • I have 4 account on my mac , but i dont want al the stuff from my kids on i cloud, is this possible?, i have 4 account on my mac , but i dont want al the stuff from my kids on i cloud, is this possible?

    i have 4 accounts on my mac , but i dont want al the stuff from my kids ( ipodtouch) on i cloud, is this possible?,

    On the Touch log out of the iCloud account. 
    If the kids know the Apple ID and password used for the iCloud account then change your password and keep it to yourself.
    OT

  • Monitoring Internet Router from inside network

    I need help in setting this up. At the moment we are using Opmanager monitor our routers inside the network. I want to monitor our internet router sitting outside the network. Be really grate if someone can help out or point me out on how to set this up.
    Regards

    Thanks for your reply. Actually what I want is for my monitoring application sitting inside my network to monitor my internet router via SNMP. There is a FW in between
    I have tried that PRTG application and its not bad. Thanks

  • My iMac keeps on diconnecting from my network and The internet is very slow on it too.

    Hi
    My iMac has been acting wierd for the past month. It has been disconnecting from the internet/network and also it has a very slow speed when using Safari or any other internet application (eg. Skype). Im not sure why this is happening. My iMac has Windows installed (100GB partioned) and yet the internet is fast on it than the Mac side. On other computers and mobiles the internet is very fast, and does not disconnect. I scanned my computer and it came up with nothing.
    Please Someone Help...

    If you connect to your router with with Wi-Fi, please try connecting with an Ethernet cable. Turn Wi-Fi off and test. Any difference?

  • Can't import from internal SD or external SD to Mac Photos app

    I have been using Photos since it was released without any issues except that I can't seem to import from SD cards.  Trying to import from either the internal SD slot on my Mac Mini or externally connected card readers fails. 
    When I choose file, import within Photos and navigate to the SD card source, the "review for import" dialog is grayed out, as are the folders themselves.  If I manually navigate to the SD card outside of Photos, I can select the files and choose open with Photos and import like that without issues.  My library is on an external drive, if that matters.  Any ideas how I can fix this or why its happening?
    thanks!

    If there is no other way, drag the images to a folder on your desktop and import them from there.
    Keep it simple

  • Backups from internal drive to external drive

    How do I transfer my backups from my internal hard drive to my external hard drive?  My internal hd is 500GB and with backups, it takes up 274GB.  My external is a 2TB hard drive with plenty of room to spare.  Any help is highly appreciated.  Thanks!

    Mac Basics: Time Machine 
    User Tip:  Most commonly used backup methods
    Emergency backups you didn't know you had!

  • Transferred all from internal drive to external drive and now need help

    I recently purchased an external hard drive to transfer allof my itunes music and folders to so it frees up my hard drive on my lap top. I followed the directions from apple to do this. When I purchased new songs this week, I plugged my ipod in and it did not take the new songs. It doesn't down load the new music.
    I have been so frustrated with all of this that I am having such a hard time being able to enjoy my new ipod 30gb.
    Can anyone help me????
    Barb

    Mac Basics: Time Machine 
    User Tip:  Most commonly used backup methods
    Emergency backups you didn't know you had!

  • Boot from internal Fusion or external SSD?

    My wife surprised me with the base level 5K iMac. It has the 1TB Fusion drive. I wish it had been upgraded to an SSD but it's too late now, I'm stuck with it. I self-upgraded to 32Mb RAM already.
    To get the best performance, would you recommend using an external SSD as a startup/boot disk, and running everything - OS X, apps, etc - from there?
    Would I see meaningful performance benefits, or should I just stick with the Fusion Drive?

    Fusion is SSD (at least in part).
    It combines the SSD with a spinning HD. I think you can opt to divide it into 2 separate disks if you are willing to reinstall the OS (or do some major juggling).
    I think the OS installer will try to force a fusion drive on supported Macs, but you may be able to clone or restore to each disk instead.
    You could buy a large SSD & run it from Thunderbolt if you want, but fusion is intended to put the most used files on the SSD with the rest on the HD.
    Some people don't like Fusion since it uses Core storage (& is new and confusing). Personally I'd give it a go to see if it performs well enough.

Maybe you are looking for

  • How to use 2 ipods on 1 itunes?

    A question asked many times me thinks, but I have to ask. How do I go about having 2 ipods (1 touch and 1 5th gen) with different music/vids on them on 1 itunes? If I connect my 5th gen to the mac I dont want all the stuff that is on my touch, I want

  • Report model dynamic connection string

    hi  I'm trying to build a report model,which has to connect to different database  For ex: I've 10 different customers, and i need to connect the selected customer database,  Any thoughts how to proceed in this  Thanks Chezhian 

  • Why won't my iTouch synch my music? Barring that, why won't it restore?

    I updated iTunes.  Then tried to synch my iTouch.  It would not synch my music.  After several tries, I attempted to restore to the original configuration.  It backed up just fine (as far as I could tell) and moved on to the next step.  After an hour

  • Protecting Images/Pictures on website

    Hi I use Dreamweaver MX 2004, and want to know how to protect images on our websites so that people cannot steal them, copy and paste them etc. Thank you very much for your help. I assume it is the same with newer formats of dreamweaver so if you kno

  • How do I remove the duplicates from my iTunes library?

    Somehow iTunes has created a duplicate of virtually every song in my over 8600 song library. There are now 16263 songs. Short of going through 1 by 1, how can I get rid of all of these duplicates? Message was edited by: SteelSpartan