RSPAN with Cat2950 Switches

Good day,
I'm trying to create a RSPAN session with 2 Catalyst 2950 switches but it doesn't work (no packets shown by the network analyzer).
I don't know what I'm doing wrong. Does anybody see any mistake in my configuration?
- all ports in VLAN 1, except of Fa0/48 (Trunk to neighbor device)
Switch 1:
vlan 99
name Monitor-VLAN
remote-span
interface FastEthernet0/24
description switch-2 Fa 0/48
switchport mode trunk
switchport nonegotiate
monitor session 1 source interface Fa0/1 rx
! Notebook for testing connected to Fa0/1
monitor session 1 destination remote vlan 99 reflector-port Fa0/23
Switch 2:
vlan 99
name Monitor-VLAN
remote-span
interface FastEthernet0/24
description switch-1 Fa 0/48
switchport mode trunk
switchport nonegotiate
monitor session 1 destination interface Fa0/1
! NW-Analyzer connected to Fa0/1
monitor session 1 source remote vlan 99
Regards,
Rolf

Amit,
sorry - I didnt see your response yesterday.
Heres the output of show version:
Switch#s vers
Cisco Internetwork Operating System Software
IOS (tm) C2950 Software (C2950-I6Q4L2-M), Version 12.1(22)EA4a, RELEASE SOFTWARE
(fc1)
Copyright (c) 1986-2005 by cisco Systems, Inc.
Compiled Fri 16-Sep-05 10:46 by yenanh
Image text-base: 0x80010000, data-base: 0x80562000
ROM: Bootstrap program is C2950 boot loader
Switch uptime is 45 minutes
System returned to ROM by power-on
System image file is "flash:/c2950-i6q4l2-mz.121-22.EA4a.bin"
cisco WS-C2950-24 (RC32300) processor (revision R0) with 21039K bytes of memory.
Processor board ID xxxxx
Last reset from system-reset
Running Standard Image
24 FastEthernet/IEEE 802.3 interface(s)
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: xxxx
Motherboard assembly number: xxxx
Power supply part number: xxxx
Motherboard serial number: xxxx
Power supply serial number: xxxx
Model revision number: R0
Motherboard revision number: A0
Model number: WS-C2950-24
System serial number: xxxx
Configuration register is 0xF
I studied the Configuring SPAN and RSPAN (Chapter 21 of Catalyst 2950 Desktop Switch Configuration Guide) again and found as a Configuration Guideline:
..., you must have EI installed on your switch.
I wonder what EI means?
Regards,
Rolf

Similar Messages

Why does the App Store not work in Genius with VoiceOver switched on

After I downloaded IOS 6 to my iPhone 4 there were a lot of things not working properly, the main things that were a problem was the App Store, to move anything with VoiceOver switched on it was touch-and then tap twice also to move the thing on the page you use three fingers swipe up or down left or right to move it. We now find that to move something in Charts you only need one finger touchon the left to move it.If Some body can come up with thee answer it is the People that work in the Accessability side of things at Apple. So if you know in Ireland why Apple cannot put in the info for Accessability for People who are Blind like me we cannot see what is going on we do not change anyof the settings...

Thank you very much for the reply. That certainly makes sense, as I am sure it is all the Time Machine backups I have that are at the root of the problem. How can I update all those older version Apps deeply embedded within my TM backups, or is the solution to unmount my 2TB drive that I use for TM?
I suppose if Apple could somehow direct the App Store to disregard all those other apps in TM, the problem would be resolved.
 Nick Andriash 
17" MacBook Pro, 2.3GHz Intel Core i7, Memory 16 GB, OS X 10.8
AMD Radeon HD 6750M 1024 MB
iPad2 WiFi & 3G, 64GB
iPhone4S 32GB

My ipod touch will not switch on and is no longer recognised by itunes. Before this i tried to restore it as I was having some problems with it switching off and on by itself randomly.

My ipod touch will not switch on and is no longer recognized by itunes. Before this i tried to restore it as I was having some problems with it switching off and on by itself randomly.
I tried to restore it and I got error code 2009, so I closed it tried again got error code 1659, now it wont do anything and it's not recognized by my pc /itunes please help x

For the restore error messages try:
iTunes: Specific update-and-restore error messages and advanced troubleshooting

Intel iMac; upgraded adobe flash; bluetooth keyboard no longer pairs but magic mouse still OK. With Bluetooth switched on the screen splits into 4 areas and open windows seperate and shrink. Switch off Bluetooth and problem disappears and iMac works OK

Intel iMac; upgraded adobe flash; bluetooth keyboard no longer pairs but magic mouse still OK. With Bluetooth switched on the screen splits into 4 areas and open windows seperate and shrink. Switch off Bluetooth and problem disappears and iMac works OK with plug-in keyboard and mouse

Hi, Derek -
...the screen splits into 4 areas and open windows seperate and shrink.
Sounds like Spaces is being activated somehow. With the wired keyboard and mouse in use, select the Exposé & Spaces control pane in System Preferences, click the choice in that pane for Spaces. See what the settings are. There are some activation settings in that pane - by default, F8 activates it.
It could be that the bluetooth keyboard has some stuck keys and is activating Spaces; or that the activation command has somehow been reset to something that the bluetooth mouse, or bluetooth itself, is triggering.

New 150/65 only at 94 Download AND Won't Work with Gigabit Switch

I just had this installed today, converting up from the 35/35, and ran into these two problems:
1. The 150 download is only resulting in a 94.87 Mpbs. The installer originally said it must be my PC NIC card, but I do have a GB card, so there's does not appear to be legitimate reason for the shortfall there. I tried to change the link speed and duplex from "auto negotation" to "1 Gbps Full Duplex," but then my computer no longer even could connect.
2. The second issue is that I have always run my connection through a D-Link DGS-2208 Gigabit Switch because I have multiple wired ethernet computers in my office. The installer wanted to test the connection speed directly through my computer (see above) and ran into problems, so I never even tried to revert to my original setup with the switch until he left. However, when I did the Gigabit switch does not even recognize any activity when I plug the source ethernet cord into the switch. It does recognize the connection to the PC and the port is lit, but no lights from connection to the wall.
Any thoughts on what the problems could be? I've included the "additional details" from the Fios Speed test at the standard site (can't get any details from the high speed version):
Checking for Middleboxes . . . . . . . . . . . . . . . . . . Done
SendBufferSize set to [261360]
running 10s outbound test (client to server) . . . . . 42.90Mb/s
running 10s inbound test (server to client) . . . . . . 69.90Mb/s
------ Client System Details ------
OS data: Name = Windows 7, Architecture = x86, Version = 6.1
Java data: Vendor = Oracle Corporation, Version = 1.7.0_05
------ Web100 Detailed Analysis ------
Client Receive Window detected at 65340 bytes.
622 Mbps OC-12 link found.
Link set to Full Duplex mode
No network congestion discovered.
Good network cable(s) found
Normal duplex operation found.
Web100 reports the Round trip time = 6.78 msec; the Packet size = 1452 Bytes; and
No packet loss - but packets arrived out-of-order 0.02% of the time
This connection is receiver limited 37.88% of the time.
Increasing the the client's receive buffer (63.0 KB) will improve performance
This connection is sender limited 61.7% of the time.
Web100 reports TCP negotiated the optional Performance Settings to:
RFC 2018 Selective Acknowledgment: ON
RFC 896 Nagle Algorithm: ON
RFC 3168 Explicit Congestion Notification: OFF
RFC 1323 Time Stamping: OFF
RFC 1323 Window Scaling: OFF
Information: Network Middlebox is modifying MSS variable
Server IP addresses are preserved End-to-End
Information: Network Address Translation (NAT) box is modifying the Client's IP address
Server says [{edited for privacy}] but Client says [192.168.1.16]
Solved!
Go to Solution.

tdaignault wrote:
I tried to change the link speed and duplex from "auto negotation" to "1 Gbps Full Duplex," but then my computer no longer even could connect.
If your computer can't negotiate a 1Gbps connection, then that is what is limiting you to 94Mbps, which is about right for a "100Mbps" port.
There could be several reasons for this.
A bad NIC
A bad port on the switch
IMO, the most likely cause is a bad cable. 1Gbps requires all 4 pairs in the cable be connected. If only 2 of the 4 pairs are connected correctly, you will get a 100Mbps connect, but will not be able to connect at 1Gbps. Try replacing the cable with one known to work at 1Gbps.

Black screen after login while on battery with graphics switching enabled

Getting a black screen after entering my password while logging into my account while on battery with graphics switching enabled. Everything is up and running, I just can't see it.
I can log into the guest account on battery
I can log into my account while plugged into power
I can log into my account on battery if graphics switching is disabled
I believe something that is starting up in my account is causing the system to switch from integrated to discrete graphics on login, and that switch isn't working correctly on battery power.
As a work around for now, I can run with graphics switching disabled, but I'd like to solve this so I get longer battery life.
MacBook Pro Retina 15"
Mountain Lion
All updates applied

I had the same issue and managed to reslove it.
Shut down your machine.
Power it back on while holding the 'shift' key (left or right, doesn't matter)
You will see a greay progress bar go across the screen while you boot in to 'safe boot'
Once booted, login, and go to Energy Saver and turn on 'Automatic Graphics Switching'.
Reboot back in to normal mode, and you should be able to log back in and see again.
I did this without being plugged into AC power.
Hope it helps!
Cheers!

Not Working-central web-authentication with a switch and Identity Service Engine

on the followup the document "Configuration example : central web-authentication with a switch and Identity Service Engine" by Nicolas Darchis, since the redirection on the switch is not working, i'm asking for your help...
I'm using ISE Version : 1.0.4.573 and WS-C2960-24PC-L w/software 12.2(55)SE1 and image C2960-LANBASEK9-M for the access.
The interface configuration looks like this:
interface FastEthernet0/24
switchport access vlan 6
switchport mode access
switchport voice vlan 20
ip access-group webauth in
authentication event fail action next-method
authentication event server dead action authorize
authentication event server alive action reinitialize
authentication order mab
authentication priority mab
authentication port-control auto
authentication periodic
authentication timer reauthenticate server
authentication violation restrict
mab
spanning-tree portfast
end
The ACL's
Extended IP access list webauth
    10 permit ip any any
Extended IP access list redirect
    10 deny ip any host 172.22.2.38
    20 permit tcp any any eq www
    30 permit tcp any any eq 443
The ISE side configuration I follow it step by step...
When I conect the XP client, e see the following Autenthication session...
swlx0x0x#show authentication sessions interface fastEthernet 0/24
           Interface: FastEthernet0/24
          MAC Address: 0015.c549.5c99
           IP Address: 172.22.3.184
            User-Name: 00-15-C5-49-5C-99
               Status: Authz Success
               Domain: DATA
       Oper host mode: single-host
     Oper control dir: both
        Authorized By: Authentication Server
           Vlan Group: N/A
     URL Redirect ACL: redirect
         URL Redirect: https://ISE-ip:8443/guestportal/gateway?sessionId=AC16011F000000510B44FBD2&action=cwa
      Session timeout: N/A
         Idle timeout: N/A
    Common Session ID: AC16011F000000490AC1A9E2
      Acct Session ID: 0x00000077
               Handle: 0xB7000049
Runnable methods list:
       Method   State
       mab      Authc Success
But there is no redirection, and I get the the following message on switch console:
756005: Mar 28 11:40:30: epm-redirect:IP=172.22.3.184: No redirection policy for this host
756006: Mar 28 11:40:30: epm-redirect:IDB=FastEthernet0/24: In epm_host_ingress_traffic_qualify ...
I have to mention I'm using an http proxy on port 8080...
Any Ideas on what is going wrong?
Regards
Nuno

OK, so I upgraded the IOS to version
SW Version: 12.2(55)SE5, SW Image: C2960-LANBASEK9-M
I tweak with ACL's to the following:
Extended IP access list redirect
    10 permit ip any any (13 matches)
and created a DACL that is downloaded along with the authentication
Extended IP access list xACSACLx-IP-redirect-4f743d58 (per-user)
    10 permit ip any any
I can see the epm session
swlx0x0x#show epm session ip 172.22.3.74
     Admission feature: DOT1X
     ACS ACL: xACSACLx-IP-redirect-4f743d58
     URL Redirect ACL: redirect
     URL Redirect: https://ISE-ip:8443/guestportal/gateway?sessionId=AC16011F000000510B44FBD2&action=cwa
And authentication
swlx0x0x#show authentication sessions interface fastEthernet 0/24
     Interface: FastEthernet0/24
     MAC Address: 0015.c549.5c99
     IP Address: 172.22.3.74
     User-Name: 00-15-C5-49-5C-99
     Status: Authz Success
     Domain: DATA
     Oper host mode: multi-auth
     Oper control dir: both
     Authorized By: Authentication Server
     Vlan Group: N/A
     ACS ACL: xACSACLx-IP-redirect-4f743d58
     URL Redirect ACL: redirect
     URL Redirect: https://ISE-ip:8443/guestportal/gateway?sessionId=AC16011F000000510B44FBD2&action=cwa
     Session timeout: N/A
     Idle timeout: N/A
     Common Session ID: AC16011F000000160042BD98
     Acct Session ID: 0x0000001B
     Handle: 0x90000016
     Runnable methods list:
     Method   State
     mab      Authc Success
on the logging, I get the following messages...
017857: Mar 29 11:27:04: epm-redirect:IDB=FastEthernet0/24: In epm_host_ingress_traffic_qualify ...
017858: Mar 29 11:27:04: epm-redirect:epm_redirect_cache_gen_hash: IP=172.22.3.74 Hash=271
017859: Mar 29 11:27:04: epm-redirect:IP=172.22.3.74: CacheEntryGet Success
017860: Mar 29 11:27:04: epm-redirect:IP=172.22.3.74: Ingress packet on [idb= FastEthernet0/24] matched with [acl=redirect]
017861: Mar 29 11:27:04: epm-redirect:IDB=FastEthernet0/24: Enqueue the packet with if_input=FastEthernet0/24
017862: Mar 29 11:27:04: epm-redirect:IDB=FastEthernet0/24: In epm_host_ingress_traffic_process ...
017863: Mar 29 11:27:04: epm-redirect:IDB=FastEthernet0/24: Not an HTTP(s) packet
What I'm I missing?

How to use a USB-to-parallel adapter to communicate with my switch device?

My computer doesn't have a parallel port, so I must use the USB port and a USB-to-parallel adapter to communicate with my switch device. Unfortunately in WindowsXP printer configure that show USB001 Virtual printer for USB. How should I control my USB-to-Parallel converter to send the Pin1 and Pin3 high? How should I decide that I/O address in Labview (traditional LPT1 is 378AH) ?

Hi Kelvin,
I understand that you want to control pins on your serial port using LabVIEW. Since you are using Windows XP, only LabVIEW version 7.0 will be able to control the pins. The pins can be controlled by modifying the values of the access registers that windows associates with each pin. If you are using LabVIEW 7.0, then the VI's located on the Funtions >> Advanced >> Port I/O palette should help you assign values to the proper pins.
This information can also be found on another discussion forum thread located at the following url:
http://exchange.ni.com/servlet/ProcessRequest?RHIVEID=101&RPAGEID=135&HOID=506500000008000000438A0000&UCATEGORY_0=_49_%24_6_&UCATEGORY_S=0
Thanks for contacting NI, and I hope this helps.
Marcus G.
National Instruments

IBook 12 Dual USB Inverter Cable with Reed Switch

I apologise if this should go on an older thread. The last time I was trying to access what was called the angle of death thread it took so long to load I gave up.
My question is: my G3 iBook 12" 500 is working perfectly as a backup for surfing and using Word, with a fairly new replacement hard drive in it. But it has started the backlight blanking out when the screen is moved through 90 degrees. From a recent post I noticed yesterday that must have been moved, I now understood that the problem was usually, or often, to do with the need to replace the Inverter Cable with Reed Switch. I live in the UK and cannot get this done locally, but an online UK firm agrees this is usually the problem and he can fit the part and do the repair which with labour costs and postage will be not far off £100.
Is it fairly safe now to assume that this part is the root of this problem?
thanks
Tom Older
Mac Mini G4 1.25 iBook G3 500 Mac OS X (10.4.8)

Thanks for the reply clarifying the matter. In fact it's now been explained to me that with postage plus vat it goes from £31 plus tax for the part, then £75 plus tax for the labour, then £15 plus tax for the postage, which comes to £142 total.
I think I'll try to keep working at 89 degrees for a bit yet then if I have to I'll buy the part and see if I can get a cheaper way to get it installed. Don't trust myself with such a job.
Mac Mini G4 1.25 ibook G3 500 Mac OS X (10.4.8)

Has anyone deployed converged access with 3850 switches and 5760 WLCs?

Has anyone deployed a converged access network architecture with 3850 switches and 5760 WLCs? I have done lots of projects with the 5508 WLCs In a centralized deployment. Basically with this design, I manage 2 logical networks as the wireless network is an overlay over the wired network. I can design firewall to segregate traffic between the wired and wireless hence I can carry both staff and guest traffic.
Now Cisco is telling us that there is new design such that the dats plane traffic can be dropped locally through the 3850 switched. I am not sold on this and have not found any recommended best practices on when should we use a converged access architecture.
Pros
With converged access, data traffic is terminated at the MA which is on the switches, hence the WLC will not be a bottleneck? This is to prepare adoption for 802.11ac?
Less hops for voice calls from user A to user B as data control traffic is dropped locally.
Cons
Now how do I segregate guest and staff traffic if my security folks say I need a firewall?
Troubleshooting wireless client mobility will be a nightmare as the 3850 switches are MA.
Pushing and upgrading code for the Code will mean upgrading the stack of switches in the LAN riser. This will be painful in a huge campus environment like an university.
Can someone convince me why would a customer choose converged access?
Sent from Cisco Technical Support iPad App

They choose CA because of the capwap termination at the switch. You can still use a 5508 and tunnel guest to a DMZ segment if you wish. You will need a 5508 though is you want to tunnel traffic to an anchor WLC.
Sent from Cisco Technical Support iPhone App

How do I hard wire multiple airport expresses with a switch

I have two airport expresses and other hardwired devices. I am trying to get them wired together for a roaming network not to extend the network, but can't seem to get it to work with a switch.
Here is the setup Modem -> Airport Express -> 5 ports switch -> one of the ports is ran to an airport express. What I'm trying to determine is if the airport device needs to be physically plugged in to the other airport to create a roaming network or can it be ran through a switch. Notice the dotted line vs the solid line. Now obviously because I found the picture on the internet, I only have two devices not 3.
Here is mine:
Here is what i'm trying accomplish. (Image from: http://forums.macrumors.com/attachment.php?attachmentid=345142&d=1340677218)

If you have a simple modem.....then you must connect the modem directly to an AirPort....then connect the switch to the AirPort and then connect other AirPorts and devices to the switch. So, it would look like this:
Internet > Simple Modem > AirPort > Switch > Other Devices
If you have a modem/router or gateway type of device.....then you can connect the switch to the modem/router or gateway.....and then connect the AirPorts to the switch. In this case, things would look like this:
Internet > Modem/Router (Gateway) > Switch > AirPorts and other Devices
So, before we go further with this, it is important to understand what type of modem that you have, as it will dictate what you can and cannot do on the network.
What is the make and model number of the device that you call your "modem"?

Configure Word 2010 startup with /n switch.

Hello,
Opening MS Word with /n switch, Example "C:\Program Files\Microsoft Office\Office\Winword.exe" /n, Word 2010 will start a new instance of Word with no document open. Can this be done via GPO as we are looking into configuring this for hundreds
of users. Thanks.

Hi,
I don't know a direct way to realize this via GPO, but a workaround may be helpful.
Since the path for all users should be the same(C:\Program Files\Microsoft Office\Office\Winword.exe), we can make one shortcut, then modify its Properties -> Add
/n to the target behind the full path C:\Program Files\Microsoft Office\Office\Winword.exe. It will be like "C:\Program Files\Microsoft Office\Office\Winword.exe" /n
in the shortcut properties, save it to a shared folder, then create a startup script which pulls this shortcut from the shared folder to the user's local desktop.
Since I'm not a script expert, you may need to contact other resource for further assistance.
Regards,
Melon Chen
TechNet Community Support
It's recommended to download and install
Configuration Analyzer Tool (OffCAT), which is developed by Microsoft Support teams. Once the tool is installed, you can run it at any time to scan for hundreds of known issues in Office
programs. Please remember to mark the replies as answers if they help, and unmark the answers if they provide no help. If you have feedback for TechNet Support, contact
[email protected]

Correct binding order in a Cluster with logical switches, NIC teams, and vNICs on the host.

I have seen many recommendations to set the network binding order on you Hyper-V hosts to something similar to:
Management NIC
Cluster NICs
iSCSI NICS
However, all of these recommendations are for scenarios where the NICs are all physical NICs in the host.
Using Server 2012 R2, I am building converged networks with logical switches, NIC Teams, and vNICs on the host. So when I go set the network binding order, I now have all these components to deal with as well. For example, on a 4 adapter blade,
I might typically have the following items in the binding order drop-down.
4 - physical NICs (2- teamed for the 1 virtual switch, the other 2 used for iSCSI)
1 - Team interface (Datacenter_Switch)
5 - vNICs (Management, Cluster, LiveMigration, iSCSI-1, iSCSI-2)
So, should you only worry about order of the vNICS (placed at the top) and let the other components just fall to the bottom of the list? This seems to be likely to me, since the binding order applies to service access to the resources, and the other
components are not being directly accessed by network services?
Or, should the order start out with the physical resources needed to access the vNICs, followed by any intermediate resources (switches or team interfaces, then the vNICS themselves, to ensure that the resources are available to the subcompnents accessing
them?
Any help would be appreciated.
Thanks.
-Tim Reid

If by 'network binding order' you mean the order set in the Advanced Settings of the Network Connections of the Control Panel, then the most important one is to make sure the domain network is at the top of the list. Whichever network is at the top
of the list is used first for auth functions. So auth functions perform best when the proper network is placed first in the binding order. After that, I don't know that it makes much difference at all. (If it does, I'm sure my statement will
start a lively discussion. <grin>)
. : | : . : | : . tim

NTP Service on Domain Controller have problem with cisco switch

Hello!
I have Windows Server 2008 R2 SP1 Domain Controller with NTP services
The windows opertion system clients get NTP time ok.
There are problem with cisco switch, can't get time from NTP.
Can anybody help me to fix problem?
C:\Users\Sysuser>w32tm /query /configuration
[Configuration]
EventLogFlags: 2 (Local)
AnnounceFlags: 5 (Local)
TimeJumpAuditOffset: 28800 (Local)
MinPollInterval: 6 (Local)
MaxPollInterval: 10 (Local)
MaxNegPhaseCorrection: 1800 (Local)
MaxPosPhaseCorrection: 1800 (Local)
MaxAllowedPhaseOffset: 300 (Local)
FrequencyCorrectRate: 4 (Local)
PollAdjustFactor: 5 (Local)
LargePhaseOffset: 50000000 (Local)
SpikeWatchPeriod: 900 (Local)
LocalClockDispersion: 10 (Local)
HoldPeriod: 5 (Local)
PhaseCorrectRate: 7 (Local)
UpdateInterval: 100 (Local)
[TimeProviders]
NtpClient (Local)
DllName: C:\Windows\system32\w32time.dll (Local)
Enabled: 1 (Local)
InputProvider: 1 (Local)
AllowNonstandardModeCombinations: 1 (Local)
ResolvePeerBackoffMinutes: 15 (Policy)
ResolvePeerBackoffMaxTimes: 7 (Policy)
CompatibilityFlags: 2147483648 (Local)
EventLogFlags: 0 (Policy)
LargeSampleSkew: 3 (Local)
SpecialPollInterval: 3600 (Policy)
Type: NTP (Policy)
NtpServer: 10.7.0.4 (Policy)
NtpServer (Local)
DllName: C:\Windows\system32\w32time.dll (Local)
Enabled: 1 (Local)
InputProvider: 0 (Local)
AllowNonstandardModeCombinations: 1 (Local)
VMICTimeProvider (Local)
DllName: C:\Windows\System32\vmictimeprovider.dll (Local)
Enabled: 1 (Local)
InputProvider: 1 (Local)
Cisco config and errors
CISCO1#show ntp ass det
10.7.0.7 configured, insane, invalid, stratum 3
ref ID 10.7.0.4, time D5BC850F.C8400AB2 (15:50:39.782 MSK Mon Aug 19 2013)
our mode client, peer mode server, our poll intvl 1024, peer poll intvl 1024
root delay 62.50 msec, root disp 11128.04, reach 377, sync dist 11218.796
delay 6.06 msec, offset -467951.1096 msec, dispersion 56.49
precision 2**6, version 3
org time D5BC8864.F79C33A7 (16:04:52.967 MSK Mon Aug 19 2013)
rcv time D5BC8A38.EBDECB39 (16:12:40.921 MSK Mon Aug 19 2013)
xmt time D5BC8A38.EA5173BE (16:12:40.915 MSK Mon Aug 19 2013)
filtdelay = 6.06 5.87 3.23 7.90 6.41 5.17 13.03 3.43
filtoffset = -467951 -467905 -467936 -467885 -467764 -467816 -467707 -467697
filterror = 0.02 15.64 31.27 46.89 62.52 78.14 93.75 93.78

Hi,
>>I gave log on as a service right to this account in Default Domain Controllers Policy but unfortunately it was not enough
Based on your description, we can try to grant this account Allow log on locally
user right in the default domain controller policy to see if it helps.
The policy setting is:
Computer Configuration\Windows Settings\Security Settings\Local Policies\User Rights Assignment\Allow log on locally
Allow log on locally
http://technet.microsoft.com/en-us/library/cc756809(v=ws.10).aspx#feedback
TechNet Subscriber Support
If you are TechNet Subscription user and have any feedback on our support quality, please send your feedback here.
Best regards,
Frank Shen

Setup crypto for secure communication with other switches

What kind of code can be used to setup crypto for secure communication with other switches.

ok but is there any special code i need to write if i need to create a crypto secure communication between some particular switches.

RSPAN with Cat2950 Switches

Similar Messages

Maybe you are looking for