Run OPC control VI without OPC

Dear all,
i am developping a VI for use with an OPC. Since the facility is no place for softwre development, i brought the PC with Labview & OPC to my office where i want to develop the VI. Here the Facility is not connected to the PC and i recieve the error
1950679035 obviously because labview cant properly read some OPC variables.
Do you know how i could get around this error without deleting the according OPC variable? It would e finde for me to fix it to zero or something.
Thanks for answers in advance!
Solved!
Go to Solution.

I have an example project that throws the error even though it is unrelated to the OPC:
Error -1950679035 occurred at Shared Variable in variabletest.lvlib:master_subVI.vi
Possible reason(s):
LabVIEW: (Hex 0x8BBB0005) Unable to locate the shared variable in the Shared Variable Engine (SVE). Deployment of this shared variable may have failed, the SVE has not started, or the SVE is too busy to respond to this request.
This error or warning occurred while writing the following Shared Variable:
\\My Computer\variabletest\Variable10
\\129.129.213.102\variabletest\Variable10
Thank you for any help!
Attachments:
shared variable test.lvproj ‏2 KB
master_subVI.vi ‏17 KB
master_subVI_.vi ‏13 KB

Similar Messages

Auto Tune prior to running motion control program (LabVIEW)

Hi,
I am controlling Parker Compumotor (404-LXR) linear servo table via GV6 drive and PCI-7344 motion controller.
The problem is that I always have to run automatic tuning in MAX when I turn off all the system and restart it.
Before I use the automatic servo tuning in MAX, the servo table buzzes and oscillates wildly. Cabling seems to be successful as linear servo motor is completely controlled by LabVIEW after auto tuning in MAX.
I wonder how I can just run my LabVIEW program without running Auto Tune step.

Hello Gino,
Thank you for using our discussion forums. Yes, you can programmatic load the PID parameters from LabVIEW. Tune your servo using auto tune, once you are satisfied with the response look under the Control Loop tab for the PID parameters. In LabVIEW use the Load All PID Parameters.flx and use the tuned parameters from Measurement and Automation Explorer as the PID Parameters input for this VI. Place the VI before the multistart.vi. This will make sure the correct PID settings are used. I hope this helps you out. Have a nice day!
Regards,
Nipun M
Applications Engineer
National Instruments

Running gdm-control gives "Failed to establish connection"

Hi everyone,
I have Arch Linux installed running Openbox as the window manager without another desktop environment. I am trying to setup shutting down, logging out, switching user, etc.
Whenever I run any gdm-control option (e.g. "gdm-launch --shutdown"), I just get the following error:
** (process:10479): WARNING **: Failed to establish a connection with GDM: No such file or directory
Has anyone seen this before? If I just run "gdm-control" then I get the usage assistance..
Thanks!

Have you setup the GNOME Display Manager as your Display Manager, or how do you get into Openbox?

To run the java application without jdk package

i would like to know whether possible to make the java .class file as .exe file to run in window environment without the help of jdk package.....if the answer is yes,,,,,is it going to use the jvm???is it come together with window os or not and start from which windows version?? or do we need to use the jre??? actually i would like to make installation package to install an application in windowsxp....i know how to do that one in vb and i've done that one before using visual studio 6.0.....is there any possible way....but please explain in easy words and way coz i might not understand if too technical...nobody can help me in my college,,,even lecturers.....thanks a lot

i would like to know whether possible to make the java .class file as >>.exe file to run in window environment without the help of jdk >>package.....Yes it is possible, there are many tools like one mentioned above to convert your java .class program to .exe and you dont need jdk for that, though you will need JVM
if the answer is yes,,,,,is it going to use the jvm???Yes it needs a JVM
is it come together with window os or not and start from which windows >>version?? You need some tool like PJ2Exe or one mentioned above to convert it to .exe, it wont be available with OS.
or do we need to use the jre???Yes you will need to install JRE for the JVM
actually i would like to make installation package to install an >>application in windowsxp....i know how to do that one in vb and i've >>done that one before using visual studio 6.0.....is there any possible >>way....Yes it is possible,
Make a .exe of your application and using VB make a setup file which takes care of installing JRE as well as your application.
Regards
Rohan

I run a Windows 8.1 - Photoshop CS5 under Parallels on an iMac one year old and both having the latest OS. I use a NIK plugin "VIVEZA" which run fine for years without a problem. Latelt and without a reason, the NIK plugin has gone corrupt, (can not use

@I run a Windows 8.1 - Photoshop CS5 under Parallels on an iMac one year old and both having the latest OS. I use a NIK plugin "VIVEZA" which run fine for years without a problem. Latelt and without a reason, the NIK plugin has gone corrupt, (can not use it more the 2 corrections after a get a black background message that there is not enough memory) and the system stops running and a must restart is required. How do I fix this terrible problem?
If it requires a Photoshop CS5 re-install, (I belief that it may fix the problem) and re-install the two third party plugins (NIK Viveza) and (Onone Perfect Resize) how and where do I get to the proper Adobe upload page to do that.
I have tried to fix this problem by changing the memory allocations, I have spend many hours on it and are very disgusted with it but it needs to be fixed. The current memory settings are;
Ram available = 1588 MB
Range = 873 -1143 MB
Recommended Photoshop usage range = 857 however I have tried every setting to max and in between. Nothing works. Current setting = 1588 (max)
The Photoshop I use is registered, I have product # and order # .

Contact NIK for updated/upgraded versions of their plug-ins. They have been having a lot of issues with their plug-ins.

How can I do to acquire and save date in the same time and in the same file when I run continual my VI without interruption.

I've attached a VI that I am using to acquire amplitude from Spectrum analyzerse. I tried to connect amplitude ouput to the VI Write Characters To File.vi and Write to Spreadsheet File.vi. Unfortunately when I run continual this VI without interruption, labview ask me many time to enter a new file name to save a new value.
So, How can I do to aquire and save date in the same time and in the same file when I run continual my VI for example during 10 min.
Thank you in advance.
Regards,
Attachments:
HP8563E_Query_Amplitude.vi ‏37 KB

Hi,
Your VI does work perfectly. Unfortunately this not what I want to do. I've made error in my last comment. I am so sorry for this.
So I explain to you again what I want to do exactly. I want to acquire amplitude along road by my vehicle. I want to use wheel signal coming from vehicle to measure distance along road. Then I acquire 1 amplitude each 60 inches from spectrum analyzer.
I acquire from PC parallel port a coded wheel signal coming from vehicle (each period of the signal corresponds to 12 Inches). Figure attached shows the numeric signal coming from vehicle, and the corresponding values “120” and “88” that I can read from In Port vi.
So I want to acquire 1 time amplitude from spectrum analyser each 5
period of the signal that I am acquiring from parallel port.
So fist I have to find how can I count the number of period from reading the values “120” and “88” that I am acquiring from In Port (I don’t know the way to count a number of period from reading values “120” and “88”).
Here is a new algorithm.
1) i=0 (counter: number of period)
2) I read value from In Port
3) If I acquire a period
i= i+1 (another period)
4) If i is multiple of 5 (If I read 5 period)
acquire 1 time amplitude and write to the same
file this amplitude and the corresponding distance
Distance = 12*i). Remember each period of signal
Corresponds to 12 Inches).i has to take these
values: 5,10,15,20,25,35,40,45,50,55,60............
5) Back to 2 if not stop.
Thank you very much for helping me.
Regards,
Attachments:
Acquire_Amplitude_00.vi ‏59 KB
Figure_Algorithm.doc ‏26 KB

One or more ActiveX controls could not be displayed because either:1 your current security settings prohibit running ActiveX controls on this page, or 2. You have blocked a publisher of one of the controls.

hi All,
i have one of the requirement for an application, we do upload some release not in file server and that is used in application link to see the note. in this note i have converted the Excel into .HTM format(web page). this was working fine, but from last
two days all of a sudden we are recieving error as above.
one or more ActiveX controls could not be displayed because either:1 your current security settings prohibit running ActiveX controls on this page, or 2. You have blocked a publisher of one of the controls.
could anyone please help me on this.
Thanks and Regards,
krishnamurthy

Hi,
Actually Arnavsharma provided a operable method for you. But no luck, it's not invalid.
Here I also offer you an method you can try.Please delete the extra (parasite) zone from the Zones subkey :
Click Start , click Run , type regedit , and then click OK
Expand the following registry subkey
HKEY_CURRENT_USER\Software\Microsoft\Windows\CurrentVersion\Internet Settings\Zones
Delete the extra (parasite) zone from the Zones subkey
Note: The parasite zone is a pseudo-graphic number listed before zone number 0. The pseudo-graphic number looks like a miniature upper case "L"
Close the registry editor
Thanks!
We
are trying to better understand customer views on social support experience, so your participation in this
interview project would be greatly appreciated if you have time.
Thanks for helping make community forums a great place.

How to restore a control file without having its backup

Hi,
Can any one please suggest me how to restore a control file without having its backup.
Thanks

To add to what SB said, in years past the instructions for re-creating the control file manually were contained in the DBA Administration manual. It used to be and may still be common to be taking and saving a "backup control file to trace" for this purpose.
If you lost only the primary copy of the control file and it is an OS file then while the database is shutdown you can copy the secondary over the primary and then use if to start the database. If the control file is stored in ASM then there should be a way to perform the copy via ASM.
If you use rman for backups then a copy of the control file should be part of the backup process and you can retrieve it from the backup set then perform recovery using the backup control file though I do note the OP said something to the effect no backup exists. Still, I have knows of instances where the DBA did not realize that the backup set contained the control file and the spfile so I think this is worth mentioning just in case.
HTH -- Mark D Powell --

How to deploy and run EJB in eclipse without XDoclet

Hi Friends
I am new in j2ee.In my academic project i want to do some ejb programming.
For that purpose i want to write some ejb's.I have written all required class for ejb,created ejb-jar.xml file manually,weblogic .xml file manually. I am using weblogic8 as an server for deployment.
I know deployment with xdoclet but i want to know hoe to deploy ejb without xdoclet.
If u have saple code or useful link regarding this please send it as soon as possible.
Thanks in advance
How to deploy and run EJB in eclipse without XDoclet

HI Welcome to J2ee...
I am also new to this...But i ll share my ideas with you...
In EJB 3.0 No need of any Deployment Descriptors....
And If you are using Eclipse You can Deploy(as jar) using Export in File tab...
XDoclet is not mandatory...
Gopal V

I want to purchase a powerbook that will run a music program like MOTU or Pro Tools as well as run Final Cut Pro without being sluggish...any help?

I want to purchase a powerbook that will run a music program like MOTU or Pro Tools as well as run Final Cut Pro without being sluggish...any help?

The only way that would work out is if you ran exactly the versions that were made for old PowerBooks. Anything newer may require Intel and not run, or will strain the poor old G4 CPU.
Your needs have to be modest, too, because the problem with older music and video software is that they are not current as far as formats and codecs for the Web. If you want to output H.264, the current standard for YouTube/Flash video, older software may not support it, and in addition, H.264 is processor-intensive and is tailor-made for today's multi-core, 2+ GHz processors. It will overwhelm a G4. A PowerBook G4 can barely play YouTube videos.
More perspective: The PowerBooks worked great for miniDV format editing. In other words, 480i SD/standard definition video in use from the late 1990s to the late 2000s. If that is all you want to do, edit tape from an old miniDV camera to SD output, then OK.
But if you want to edit today's HD video, whether 720p from a snapshot camera/iPhone 4 or 1080p from a DSLR, the PowerBook and the software for it will either not recognize AVCHD/H.264, or it will slow the PowerBook to a dead crawl.
I'm in agreement with the above: Intel Macs have been out for so many years that getting a used one is a much better deal than a dead-end PowerBook. And I loved (still love) my PowerBooks.

Is the base modeal 15" mbp (4gb ram w/ 750gb@5400rpm) enough to run traktor and ableton without fail?

i just need to know if i can get away with buying the base 15" mbp with the 4gb ram 750gb@5400rpm hdd to sufficiantly run traktor and ableton without fail. all comments needed, very close to just saying screw it and just buying one! getting tired of waiting! thank you l;D

You could do it yourself according to this: http://manuals.info.apple.com/en_US/MacBook_Pro_17inch_Mid2010_Hard_Drive_DIY.pd f
I'm sure the difference in size doesn't make a difference to the replacement.
Here's how to add RAM without affecting AppleCare:
http://support.apple.com/kb/ht1270#link3

Can I run 9.2.2 without an OSX drive on board?

I am getting strange results on my Beige Tower running 9.2.2 (G3-366 MHz, 640 Mb ram, 6 Mb Vram, 30 gig Maxtor ATA HFS+, PCI ATI Rage 128, PCI XClaimPRo, PCI USB - not used, AppleTalk 1.1, AppleShare 3.9.2, CarbonLib 1.6, QuickTime 6.0.2).
When I use the Chooser to AppleShare connect to another machine (G4 mirror door) a type 1 error occurs and the finder notifies me to quit running applications and restart. I was getting a type 2 error the same situation but cured that by turning off the RAM disk.
After I restart, the program MyInvoices, operates incorrectly.
Can I run 9.2.2 without an OSX drive on board? I recently moved the hard drive from a G3 beige desktop with another drive running Jaguar. I use this machine for QuarkXpress production work and invoicing.
I was thinking I should wipe the drive and downgrade to 9.1. If I do, what formatting should I use for the hard drive (HFS+)?

The G3 beige now starts and runs without making the breaking glass sound.
Using TechTool Deluxe 2.5.4 on the simple test all systems pass, fpu, ram, (even my over clocked) processor, drive.
Tried TechTool again standard test, Ram only, system froze following the Vram test. Mouse moves cursor, clock stops.
Tried TechTool again using the os on the tech Tool disk (9.0.4), passed ram including vram. Mouse moves cursor, clock stops.
Tried TechTool again standard test running from 9.2.2 on hard drive, froze following vram test.Mouse moves cursor, clock stops.
Restart extensions off. Tried TechTool again standard test running from 9.2.2 on hard drive, froze following vram test. Mouse moves cursor, clock stops.

When will Quicken run on Intel Mac without Rosetta?

I've been holding off on buying Quicken for my mac mini. Anybody know when Intuit will release a version of Quicken that runs on Intel Mac without needing Rosetta? Thanks,
Owen

Kappy,
I just looked at the Quicken Support site:
https://quicken.custhelp.com/cgi-bin/quicken.cfg/php/enduser/stdadp.php?p_faqid=4014&p_created=1137099411&p_sid=9RFCSgti&p_accessibility=0&p_lva =3793&p_sp=cF9zcmNoPTEmcF9zb3J0X2J5PSZwX2dyaWRzb3J0PSZwX3Jvd19jbnQ9MSZwX3Byb2RzP Tk1LDU1MSZwX2NhdHM9JnBfcHY9Mi41NTEmcF9jdj0mcF9wYWdlPTEmcF9zZWFyY2hfdGV4dD1pbnRlb A**&p_li=&ptopview=1
This is what it says regarding Quicken 2007 for mac in response to the question "Tell me about running Quicken on the new Intel based macs":
"Quicken for Mac is not a universal binary program and will not run natively on an Intel based Mac. All Intel based Macs come equipped with Rosetta software that enables non-universal binary programs to run on Intel Macs. There are no known issues specific to using Quicken 2006 and later on an Intel Mac with Rosetta."
What is the source of your info? Thanks,
Owen

Can I get rid of a windows partition on a MacBook running 10.4.11 without having bootcamp or bootcamp beta?

Can I get rid of a windows partition on a MacBook running 10.4.11 without having bootcamp or bootcamp beta? If so, how?

Yes, I think so, as would Snow Leopard probably. If your computer meets the requirements it would only cost $29 to buy Snow Leopard versus $129 for Leopard.
Snow Leopard General requirements
Mac computer with an Intel processor
1GB of memory
5GB of available disk space
DVD drive for installation
Some features require a compatible Internet service provider; fees may apply.
Some features require Apple’s MobileMe service; fees and terms apply.
Leopard System requirements
You must have a Macintosh computer with:
an Intel processor or a PowerPC G4 (867 MHz or faster) or G5 processor
a DVD drive >built-in FireWire
at least 512 MB of RAM (additional RAM is recommended for development purposes)
a built-in display or a display connected to an Apple-supplied video card supported by your computer
at least 9 GB of disk space available, or 12 GB of disk space if you install the developer tools

Will Developer 6i run on Windows 7 without any problems?

Will Developer 6i run on Windows 7 without any problems? and developer 6i supports on windows 7 or not.

Hi,
As a matter of fact the Dev 6i tools (form and report builder) is supported and will be supported as they are certified with E-business 11.5.x.x. version....product
Take a look at :
"Which Version Of Dev 6i Tools (Reports & Forms Builder) Is Supported With E-Business Suite 11.5" (Metalink Note:418667.1)
Greetings,
Sim

Is it possible to create a control file without the datafiles

Hi All,
Is it possible to create a control file without the datafiles?
on any OS or DB version
regards,
sachin

if I understand properly:
- you have a script to recreate the controlfile
- you have all of your database files backed up except your controlfiles
This should work as this is how we sometimes refresh dev databases:
1) restore the copies of the database files
2) recreate the controlfile
3) recover the database files to the desired point in time (if hot backup or archivelogs are available, otherwise, it would be as of the time of the backup)
4) add temp files to temporary tablespace(s)
The simpler solution would be to backup your controlfile at the same time as your datafiles (RMAN or o/s copy).
I hope I understood your question properly.

Run OPC control VI without OPC

Similar Messages

Maybe you are looking for