"runas command not supported"

What is this statement?

Hi.
What are you trying to do?
Do you have enough permissions to use run as?
Please check this page:
How to enable and use the "Run As" command when running programs in Windows
Please click on Propose As Answer or to mark this post as and helpful for other people. This posting is provided AS-IS with no warranties, and confers no rights.

Similar Messages

QOS: egress police command not supported in non-leaf classes

Hello,
I have issue with egress policers on EFP (Service instance).
When configure two egress policers on EFPs (on one physical interface), I received a message:
ME-3600X(config-if-srv)#service-policy output VLAN-50M
QOS: egress police command not supported in non-leaf classes
QoS: Policy attachment failed for policymap VLAN-50M
The configuration looks easy:
policy-map VLAN-50M
class VLAN
police cir 50000000
exceed-action drop
class-map match-all VLAN
match protocol ip
interface GigabitEthernet0/11
description TEST
switchport trunk allowed vlan none
switchport mode trunk
mtu 1998
load-interval 30
service instance 199 ethernet
encapsulation dot1q 199
rewrite ingress tag pop 1 symmetric
service-policy output VLAN-50M
xconnect 82.119.245.231 3291 encapsulation mpls
service instance 500 ethernet
description L2MNG-SWITCHE
encapsulation dot1q 500
rewrite ingress tag pop 1 symmetric
bridge-domain 500
I tried to attach the same policy-map to Service Instance 500, with the messages above mentioned.
I am not sure if this is correct behaviour, and what means term "non-leaf class".
IOS version is 15.2(4)S2 with AdvancedMetroIPAccess.
Best regards,
Josef

Platform supports three level hierarchy - Port, VLAN and Class.
Class is the leaf level.
Queuing is done only at the leaf level.
You need to attach your policy to the port level policy so that it can be a two level policy.
Three Level Class-default Policy Example:
policy-map leaf
class class-default
queue-limit xxxxx bytes
policy-map logical
class class-default
service-policy leaf
policy-map root
class class-default
service-policy logical
Invalid Queue-Limit Policy Configuration Example:
This case "class-default" is being considered as the port level.
Following QOS policy configuration failed because the configuration check assumes user is trying to apply the queue-limit at the vlan level which is not supported.
policy-map child-1
class class-default
queue-limit 256 packets
policy-map VLAN-OUT
class class-default <<< Class default is being assumed at the port level , Child policy at the second level
shape average 5000000
service-policy child-1
interface GigabitEthernet0/5
switchport trunk allowed vlan none
switchport mode trunk
service instance 2 ethernet
encapsulation dot1q 60
rewrite ingress tag pop 1 symmetric
bridge-domain 60
3600-HL-2-N(config)#interface GigabitEthernet0/5
3600-HL-2-N(config-if-srv)#service-policy output VLAN-OUT
QOS: queue-limit command not supported in non-leaf classes
QoS: Policy attachment failed for policymap VLAN-OUT
*Feb 13 09:55:28.700: %QOSMGR-3-QLIMIT_LEVEL_ERROR: Qlimit command not supported in non-leaf classes

WbAdmin Delete Backup command not supported in 8.1 Pro x64

Hello
I've searched for how to delete specific backups that I've created using the elevated Power Shell command "wbAdmin start backup -backupTarget:E: -include:C: -allCritical -quiet" but I've run into a roadblock.
The problem is that none
of the "wbadmin delete xxx" commands are actually supported in Win8.1 Pro 64-bit (6.3, Build 9600). If I type "wbadmin delete /?", I get:
---- Commands Supported ----
DELETE CATALOG                     -- Deletes the backup catalog.
DELETE SYSTEMSTATEBACKUP -- Deletes one or more system state backups.
DELETE BACKUP                       -- Deletes one or more backups.
However, when I try to use ANY delete command (for example, to delete a specific backup version that was identified using "Wbadmin get versions"), I get this error:
PS C:\WINDOWS\system32> wbadmin delete backup -version:06/26/2014-07:29
wbadmin 1.0 - Backup command-line tool
(C) Copyright 2013 Microsoft Corporation. All rights reserved.
Warning: The DELETE BACKUP command is not supported in this version of Windows.
The operation ended before completion.
The same thing happens if I use -deleteOldest, with or without the -backupTarget switch.
Does anyone know why the Delete command is not available on 8.1? Is there a patch, workaround or alternate method of deleting specific backup images?

Yolanda, thank you for confirming the issue and for pointing me to a solution. I really appreciate it!
I have looked at the cmdlet reference page tried to use the commands but it appears that they do not work on my system. For example:
PS C:\WINDOWS\system32> remove-wbcatalog
remove-wbcatalog : The term 'remove-wbcatalog' is not recognized as the name of a cmdlet, function, script file, or
operable program. Check the spelling of the name, or if a path was included, verify that the path is correct and try
again.
At line:1 char:1
+ remove-wbcatalog
+ ~~~~~~~~~~~~~~~~
    + CategoryInfo          : ObjectNotFound: (remove-wbcatalog:String) [], CommandNotFoundException
    + FullyQualifiedErrorId : CommandNotFoundException
Also, if I type the help command listed on the reference page, get-help -module windowsserverbackup, the only reponse is a blank command prompt. Do I need to install the windowsserverbackup functionality separately? It does not seem
to be built-in.

Safari browser version you are running does not support community tool bar. what's that mean and where is it coming from or how do I get rid of it ?

I keep getting the message "Safari browser version you are useing does not support community tool bar." Where is this coming from and how do I get rid of it ?

That toolbar/ct plugin causes problems for all who install it!
Close Safari, then locate and delete the following files and it should be gone:
/Library/Application Support/Conduit
/Library/InputManagers/CTLoader
/Library/Receipts/ctloader.pkg
/Library/Receipts/<Toolbar name>.pkg
/Library/Application Support/SIMBL/Plugins/CT2285220.bundle
/Users/<User name>/Library/Application Support/Conduit
where / is the root library on your Hard Disk.
If you are running Snow Leopard you should also look here:
Library/launchAgents/com.conduit.loader.agent.plist
Library/Application support/conduit plugins
Note: Safari does not support any third-party toolbars except those supplied as an extension to Safari via the Extension Gallery.

Does "aaa accounting commands" not support radius?

When I issue this command:
aaa accounting commands 15 default start-stop group myradiusgroup
I get this error: %AAAA-4-SERVNOTACPLUS: The server-group "myradiusgroup" is not a tacacs+ server group. Please define "myradiusgroup" as a tacacs+ server group.
No where in the documentation could I find anything saying the "commmands" accounting type is only available to tacacs+. Does aaa not support this accounting type for radius?

Hi Red,
The Cisco implementation of RADIUS does not support command accounting. So that's the reason you are getting that error. Please use TACACS if you want to use this.
Regards,
Kanwal
Note: Please mark answers if they are helpful.

SQLPLUS HOST Command Not Supported

Hi,
I am facing strange problem. I have lots of scripts where I have used the HOST command from within SQLPLUS.
Now, on Windows Server 3000 Standard Edition, Version 5.2, I find that both HOST and its equivalent $, both are not supported when used with SQLPLUS on Oracle 10g Enterprise Edition.
Please HELP, and suggest some alternative.
Prashant

There is no such thing as Windows Server 3000. The latest product appears to be Windows Server 2008.
I'm not sure what the version of the Oracle database has to do with it. This is about SQL*Plus and you still haven't told us what version of that you are using. For example:
SQL*Plus: Release 11.1.0.6.0 - Production on Sat Dec 6 15:56:12 2008
Copyright (c) 1982, 2007, Oracle. All rights reserved.
Connected to:
Oracle Database 11g Enterprise Edition Release 11.1.0.6.0 - Production
With the Partitioning, OLAP, Data Mining and Real Application Testing options
SQL> host cd
y:\sql
SQL>This is sqlplus.exe (never sqlplusw.exe) version 11.1.0.6.0 on Windows XP Pro 2002 SP3. It's not the best example because SQL*Plus and the database are at the same version - they are often different. For example:
/Users/williamr: sqlplus william/x@//vm.starbase.local:1521/eleven
SQL*Plus: Release 10.1.0.3.0 - Production on Sat Dec 6 16:01:21 2008
Copyright (c) 1982, 2004, Oracle. All rights reserved.
Connected to:
Oracle Database 11g Enterprise Edition Release 11.1.0.6.0 - Production
With the Partitioning, OLAP, Data Mining and Real Application Testing options
SQL> ho uname -a
Darwin starbase-2.local 8.11.1 Darwin Kernel Version 8.11.1: Wed Oct 10 18:23:28 PDT 2007; root:xnu-792.25.20~1/RELEASE_I386 i386 i386
SQL> I've never known the host command not work, but perhaps someone with the same setup as you can confirm they don't have the same problem. I'm also a bit puzzled by the error message "Command not success." That doesn't sound like an Oracle command - apart from being vague and ungrammatical it doesn't start with the standard "SP2-nnnn" prefix, for example:
SQL> x
SP2-0042: unknown command "x" - rest of line ignored.Can you copy and paste the exact commands and results you get?
Edited by: William Robertson on Dec 6, 2008 4:04 PM

FTP server: PORT command not supported??

Hi,
In a nutshell - we are trying to set up PASV -- PORT connection between a Tiger server (10.4.11) and another system (say it's a windows FTP server). Issuing a PORT command to a Tiger FTP server fails with this error:
-> PORT 192,168,11,3,199,158
<- 500 Invalid PORT command
I have done some research on the web and as far as I can see - this is just a feature that is disabled in Mac OS X ftp server.
What's strange is that "features" command states that PORT is supported.
Has anyone seen PORT command work for a Tiger Server ftp daemon?
Has anyone succeeded enabling this command on a Tiger server?
Can you recommend another FTP server that works well on a Tiger server?
Thanks a million,
Darius

Passive (PASV) and Port (PORT) mechanisms are orthagonal.
If you're working with PORT, then you're almost certainly trying to clear through one or more firewalls. And a firewall can also trigger the Illegal Port Command error for a PORT command.
(Though I don't see a PORT command in the Mac OS X ftp client. I've checked a couple of clients, and it isn't common to expose it.)
ftp is a mess. Insecure, difficult to configure, insecure, firewall unfriendly, insecure, and slow. And did I mention insecure?
(No, I'm not a big fan of ftp.)
Some reading material:
http://www.cert.org/techtips/ftp_portattacks.html
http://www.slacksite.com/other/ftp.html
http://cr.yp.to/ftp/security.html
As for a suggestion, chuck ftp and switch to sftp.

Some script logic commands not supported any longer

Hello, it seems like Prior, *APP(in runallocation), *Name in runallocation...these commands are no longer supported in MS 7.5. I ran the same script logic under MS 5.1 it passes validation in script logic. but in 7.5 it gives error. please advise. thanks.

Hi Tom
I don't see where you define or set value for #TEMP_REV and #TEMP_VIS
something like
*WHEN CATEGORY.FLAG
*IS = Y
*REC(CATEGORY=#TEMP_VIS)
*ELSE
*REC(CATEGORY=#TEMP_REV)
*ENDWHEN
*GO

Evernote, kakaotalk, and many other apps NOT supported for bb10??

is it just me or are there others who run into 'not supported' when trying to download app?
my q10 allows me to add Evernote account but when i search for the actual app in the bbWorld, it does not exist. When trying to download from Evernote website, it takes me to bbworld only to let me know that it's not yet supported.
very frustrating...

Correct.
The full Evernote application will be availble with OS 10.2, hopefully witin a six weeks.
1. If any post helps you please click the below the post(s) that helped you.
2. Please resolve your thread by marking the post "Solution?" which solved it for you!
3. Install free BlackBerry Protect today for backups of contacts and data.
4. Guide to Unlocking your BlackBerry & Unlock Codes
Join our BBM Channels (Beta)
BlackBerry Support Forums Channel
PIN: C0001B7B4 Display/Scan Bar Code
Knowledge Base Updates
PIN: C0005A9AA Display/Scan Bar Code

Could not complete the video frames to layers command because photoshop does not support video in th

When I attempt to import a video I get the message "could not complete the video frames to layers command because photoshop does not support video in this version of windows" I am running on windows 8.1 pro (32 bit), shouldn't this be compatible???????????

Unfortunatly, the 32 bit versions of windows doesn't support video in photoshop cc.
see this post:
http://forums.adobe.com/message/5802978#5802978

OATS CPU does not support the SSE2 instruction set required to run JRockit

Hello,
I am trying to get the OATS agents to work on some injector machines, however, when I try to start them I get the following error:
"[ERROR] Your CPU does not support the SSE2 instruction set required to run JRockit.
Could not create the Java Virtual Machine."
Is there a way to configure OATs to use the Sun JDK instead? I have the Sun JDK in my path and JAVA_HOME set accordingly, however that doesn't seem to make a difference. Alternatively, is there a workaround to this problem?
Thanks,
Michael.

Hi Tab,
In this case, SQL Server Analysis Services doesn’t support Distributed Transactions by design. Here is a similar thread about this issue for your reference, please see:
http://social.technet.microsoft.com/Forums/en-US/8b07be45-01b6-49d4-b773-9f441c0e44c9/olaplinked-server-error-msolap-for-linked-server-olaplinked-server-does-not-support-the?forum=sqlanalysisservices
One workaround is that use SQLCMD to execute the EXEC AT command and saved the results to a file, then import using SSIS.
If you have any feedback on our support, please click
here.
Regards,
Elvis Long
TechNet Community Support

CSM - show run module # - diagnostic not supported

Hi, I´d like to know why show run module # (where is CSM) doesn´t show anything that I´ve configured before. I have CSM 3.1(5) and IOS 12.1(19)E1 with SUP2 MSFC2. Is this supported or a Bug ?
I also would like to know if it´s normal to appear not supported CSM module (6) when I use the command show module. This is because I can use CSM without problems. Is this supported or a Bug ?
Router#show module
Mod Online Diag Status
1 Pass
3 Pass
4 Pass
6 Not Supported
Thank you !!

Hi Joerg,
There´s no problem with show run if you want to see CSM configuration, but if you use IOS 12.2(14)SX1 with SUP720 you can use the command show run module # (where is CSM) and appears what you want.
I ´d like to know if this command is not supported with SUP2 and IOS 12.1(19)E1 or if it is a cosmetic Bug. I was searching in the Bug Toolkit and Release Notes and I didn´t find anything about it.
Could you give me a link where I can see "online diagnostics are not supported for CSM" ?.
Thank you.

Shell Commands not found error when running application

Hello,
Im using MonoDevelop IDE in my Mac, before it used to work fine but after few days, now when I'm opening the application nothing happens., i checked the Console for the log and it says this
May 9 21:29:39 Sri-Vishnu-Totakuras-MacBook-Pro [0x0-0x52052].com.ximian.monodevelop[1510]: /Applications/MonoDevelop.app/Contents/MacOS/monodevelop: line 17: dirname: command not found
May 9 21:29:39 Sri-Vishnu-Totakuras-MacBook-Pro [0x0-0x52052].com.ximian.monodevelop[1510]: /Applications/MonoDevelop.app/Contents/MacOS/monodevelop: line 31: //mono-version-check: No such file or directory
May 9 21:29:39 Sri-Vishnu-Totakuras-MacBook-Pro com.apple.launchd.peruser.501[599] ([0x0-0x52052].com.ximian.monodevelop[1510]): Exited with code: 1
I thought may be some error with the "dirname" command, so i commented it in the code and gave the path of directory myself and then the console shows up like this.
May 9 21:34:12 Sri-Vishnu-Totakuras-MacBook-Pro [0x0-0x56056].com.ximian.monodevelop[1532]: /Applications/MonoDevelop.app/Contents/MacOS//mono-version-check: line 19: grep: command not found
May 9 21:34:12 Sri-Vishnu-Totakuras-MacBook-Pro [0x0-0x56056].com.ximian.monodevelop[1532]: /Applications/MonoDevelop.app/Contents/MacOS//mono-version-check: line 19: cut: command not found
May 9 21:34:12 Sri-Vishnu-Totakuras-MacBook-Pro [0x0-0x56056].com.ximian.monodevelop[1532]: /Applications/MonoDevelop.app/Contents/MacOS//mono-version-check: line 20: cut: command not found
May 9 21:34:12 Sri-Vishnu-Totakuras-MacBook-Pro [0x0-0x56056].com.ximian.monodevelop[1532]: /Applications/MonoDevelop.app/Contents/MacOS//mono-version-check: line 21: cut: command not found
May 9 21:34:12 Sri-Vishnu-Totakuras-MacBook-Pro [0x0-0x56056].com.ximian.monodevelop[1532]: /Applications/MonoDevelop.app/Contents/MacOS//mono-version-check: line 22: cut: command not found
May 9 21:34:12 Sri-Vishnu-Totakuras-MacBook-Pro [0x0-0x56056].com.ximian.monodevelop[1532]: /Applications/MonoDevelop.app/Contents/MacOS//mono-version-check: line 31: osascript: command not found
May 9 21:34:12 Sri-Vishnu-Totakuras-MacBook-Pro [0x0-0x56056].com.ximian.monodevelop[1532]: Cannot launch MonoDevelop
May 9 21:34:12 Sri-Vishnu-Totakuras-MacBook-Pro [0x0-0x56056].com.ximian.monodevelop[1532]: MonoDevelop requires the Mono Framework version 2.10.4 or later.
May 9 21:34:12 Sri-Vishnu-Totakuras-MacBook-Pro com.apple.launchd.peruser.501[599] ([0x0-0x56056].com.ximian.monodevelop[1532]): Exited with code: 1
I opened the contents of the application and run the shell script for opening aplication there it worked very fine and application started working.. But if i open application directly through launchpad or finder it doesnt show up and console
I tried running those commands in the terminal directly there they work.. But dunno whats wrong in here. and even if try to open the application through the terminal it all opens fine.. what could be the possible problem, is it with my mac..?

i finally figured out the problem.. it is with the environmental variables. the path for all those commands like "grep" is not being set for the GUI applications. that is why i got that error.
for those GUI applications which require path, we have to set path in the file /etc/launchd.conf the environmental variables set in here are used by the gui applications and those which are launched through spotlight.
that file may bot be present in most of the macs. No problem even if not present,we can create one and use.
so type in terminal
$ sudo vi /etc/launchd.conf
and in the editor add these lines
setenv PATH = /new/path
and save. Note: replace /new/path with the path which you need to have for the commands used in the script.
remeber that you need to restart your mac for applications to use these environmental variables.

I have just purchased a lightning to 30 pin adaptor to use on an iPad mini and a gen5 iPod touch both devices are running iOS 8.1.3 and come up with The error message "this accessory is not supported by this device "

I have just purchased a lightning to 30 pin adaptor to use on an iPad mini and a gen5 iPod touch both devices are running iOS 8.1.3 and come up with The error message "this accessory is not supported by this device "
THis is means they are not charging on a 30 pin cable and the touch won't work in my Apple iPod dock - no audio out or charge. Have re powered both devices to no avail am wondering if the iOS version is the problem
Help!

If it is a lightning to 30 pin adaptor, and you have a 7th Generation Nano it has to fit the Nano.
This is lightning to 30 pin adapter: http://www.bestbuy.com/site/Apple%26%23174%3B---Lightning-to-30-Pin-Adapter/6651 936.p?id=1218803450821&skuId=6651936#tab=overview
Is this what you bought?
You need to contact Sony and see if they model you have is compatible with the docking adapter. It may not be.

I downloaded Firefox 4 onto my PowerPC G4 1.67GHz running Mac OSX 10.5.6. When I try to open it I get error message You cannot open the application "Firefox" because it is not supported on this architecture. I can't find my Firefox 3.6.16 I'm on Safari.

I just want to download Firefox 3.6 again
I downloaded Firefox 4 onto my PowerPC G4, 1.67GHz running Mac OSX 10.5.6. When I try to open it I get error message You cannot open the application “Firefox” because it is not supported on this architecture.

Use Tony's suggestion. I am running it right now and it is awesome. I love Mozilla but they basically screwed all of those older Macs over. Come on Mozilla. These Macs still work, and there are plenty of people with them out there.

"runas command not supported"

Similar Messages

Maybe you are looking for