RV016 Router Allow All Traffic For Outside IP

Hi,
I need to configure the firewall to allow all traffice for an IP address of a sever. What steps in the router do i need to configure this? This is a cloud based voip server and we have IP phones and we need to add an IP address of the phone server to allow all traffic for that IP.
thanks.

Hi Jonathan,
I have a similar problem with VOIP traffic being dropped by my new RV016 v3 router.
I have created one Firewall Rule, to allow ALL traffic from the external VOIP PBX provider (single IP) to connect to the internal VOIP phones, which have assigned addresses in a small IP Address range (eg. 10.1.2.50 - 10.1.2.59)
The Aastra VOIP phones continually loose their registration wtih the cloud-based PBX. If you make an outgoing call, it will work, but the PBX will lose connection with the phone, 3 or 4 minutes after you hang up, and will mark it as offline. Incoming calls made within the 3 or 4 minutes will get through, but after that they go right to voicemail on the PBX system.
We used to have an RV016 v2 router and VOIP traffic worked OK, with a similar Firewall Rule. We replaced the v2 router because its CPU crashed.
I tested the VOIP traffic with a WRT160 router with minimal Firewall Rules, and it works OK, as long as SIP-ALG is turned Off. We want to use the RV016 because it provides a larger number of ports for our LAN.
Any suggestions ?
Kirk

Similar Messages

Firewall Allow all traffic on lan

Is there a way to make a firewall rule to allow all traffic on en1? I have my ip ranges set to allow all traffic, but I still have to turn the firewall off for DHCP to give IP addresses to new devices on the network.

dtich wrote:
thx dean, yes, i had certainly looked at the log, which shows these entries:
Nov 11 21:49:25 north-knoll-server ipfw[8789]: 65534 Deny UDP 169.254.14.242:138 169.254.255.255:138 in via en0
but i have no idea where 169xxx is, nothing on my lan... if the port is 65534, that's an ftp passive port, tried opening that, doesn't solve the problem. if the port is 138, that's netbios, which would be odd, but i tried opening that too. nothing doing. can't figure it out. and the log really isn't helping too much.
traceroute gives me:
traceroute to 169.254.14.242 (169.254.14.242), 64 hops max, 40 byte packets
1 169.254.14.242 (169.254.14.242) 0.593 ms 0.504 ms 0.195 ms
so, i guess that's some internal address that my router uses or something..?? wacky. i'm out of my depth here.
if i allow 169.254.x.x, i still get no joy.
mean anything else to you?
yeah, 169.254.x.x is part of the zeroconf net address range. (See http://en.wikipedia.org/wiki/Zeroconf for more details)
Not sure why the device in particular is trying port 138 unless it's Windows box maybe? Is en0 on your local network or external?

Firewall blocks Airplay (even under 'allow all traffic')

Hi every body,
I am somewhat at the end of my knowledge. I have a mac mini server running Lion 10.7.2 server. Interestingly, my the server's firewall blocks
a) all airplay traffic and
b) 'reading Airport confirguration' requests
even when the firewall is set to 'allow all traffic'. However, when I completely switch it off, everything works just fine.
Any help would really be appreciated.
Thanks a lot.
Nonresidentalien
P.S. I have also tried to open ports 80 (t), 443(t), 554 (t/u), 3689(t), 5297(t), 5289(t/u), 5353(u), 49159(u) and 49163(u) with no success

Pointing to the IPv6 thread was a good idea. After reading it, I found out that the firewall preferences in Server Admin only show you IPv4 related firewall rules.
There is a terminal command that allows you to play with IPv6 rules. And by doing so, I was actually able to get AirPlay working again.
First, you want to show you the current IPv6 firewall rules. In my case they looked like this (10.7.2):
reptilehouse:~ sascha$ sudo ip6fw show
01000        285      96163 allow ipv6 from any to any via lo0
01100         66       5750 allow ipv6 from any to ff02::/16
65000          0          0 deny ipv6 from any to any
65535          6        306 allow ipv6 from any to any
As you can see, rule number 01100 only allows traffic to the local subnet, while the next rule (65000) blocks anything else. So you want to get rid of 65000:
reptilehouse:~ sascha$ sudo ip6fw delete 65000
To confirm, show the rule table again and you should see 65000 is gone:
reptilehouse:~ sascha$ sudo ip6fw show
01000        285      96163 allow ipv6 from any to any via lo0
01100         66       5750 allow ipv6 from any to ff02::/16
65535          6        306 allow ipv6 from any to any
Mind you, the rule numbers could be different on your system and you could see more or less rules. But you get the idea.
What I don't know if whether this is sticky, e.g. survives a reboot.

ACE 4710: Config Allows all traffic except large HTTP downloads

Hi Folks,
Got an ACE 4710 with a basic config that seems to work for all traffic except large downloads.
I've attached the current config
As I mentioned I can do normal HTTP to a standard destination like google or SSH through the ACE or ICMP
If i try to get a large file from the server side of ACE, then a trace shows that the first and subsequent 1460Byte packets dont go through ACE
I've thought of parse lengths, but i cannot see any that seem to affect the generic L4 maps that I am trying to use
Cheers
Alan

I've seen a similar fault. I suppose a lower MSS was sent in the TCP SYN handshake packets (1300 or 1380?) and the packets exceeding that value were dropped by the ACE. This is the default behavior which can be switched to a less strict mode by either
exceed-mss allow
or
no normalization
commands.
In our case, a linux web server was whose replies wouldn't keep to the MSS limit.

How do I remove "Allow all connections" for Pando in my firewall settings?

In System Information under Firewall Settings - Applications, I see the following: com.pando.pando: Allow all connections. However, when I go to System Preferences and look at the firewall options, this is not listed, nor can I find any trace of Pando anywhere else on my computer. Is this hidden somewhere, and how can I get rid of it?

pirihi,
open Safari’s Preferences, and select its Privacy tab. For the “Block cookies and other website data” set of radio buttons, select “Never”.

Iptables and tor, reroute all traffic for security... Help?

I'm attempting to route all TCP traffic that does not go through polipo through port 9040, tor's default TransPort. My web browser uses polipo to cache stuff, so I'd like to keep it in place if possible. However, all non-http traffic needs to be sent through the transPort. My current config, which does not take into account rerouting, is below:
# Generated by iptables-save v1.4.15 on Fri Oct 12 16:33:33 2012
#*nat
#:PREROUTING ACCEPT [12:3420]
#:INPUT ACCEPT [1:261]
#:OUTPUT ACCEPT [0:0]
#:POSTROUTING ACCEPT [0:0]
#-A OUTPUT ! -p tcp -m owner --owner-uid tor -j REDIRECT --to-ports 9040
#-A OUTPUT -p udp --dport 53 -j REDIRECT --to-ports 9053
#COMMIT
# Completed on Fri Oct 12 16:33:33 2012
# Generated by iptables-save v1.4.15 on Fri Oct 12 16:33:33 2012
*filter
:INPUT DROP [9:1175]
:FORWARD ACCEPT [0:0]
:OUTPUT DROP [8:488]
# allow loopback
-A INPUT -i lo -j ACCEPT
-A OUTPUT -o lo -j ACCEPT
# allow NTPD time syncs
-A OUTPUT -p udp --dport 123 -j ACCEPT
# allow tor
-A OUTPUT -j ACCEPT -m owner --uid-owner tor
-A OUTPUT -p tcp --dport 9040 -j ACCEPT
-A OUTPUT -p udp --dport 53 -j ACCEPT
# allow BitTorrent
-A OUTPUT -p tcp --dport 6969 -j ACCEPT
-A OUTPUT -p tcp --dport 51413 -j ACCEPT
-A OUTPUT -p udp --dport 51413 -j ACCEPT
# allow pings (still not working. fix?)
-A OUTPUT -p icmp --icmp-type 8 -j ACCEPT
-A INPUT -p icmp --icmp-type 8 -m conntrack --ctstate NEW -j ACCEPT
# allow traffic on established connections
-A INPUT -m conntrack --ctstate RELATED,ESTABLISHED -j ACCEPT
-A INPUT -m conntrack --ctstate INVALID -j DROP
COMMIT
# Completed on Fri Oct 12 16:33:33 2012
as you can see, I've already tried to redirect traffic using the --uid-owner polipo rule. So far, it's just caused iptables to spit out errors. I'm stumped, so I thought I'd come to you wonderful people at the Archlinux forums for help.

Using the command you gave me, I found that the polipo user is indeed executing /usr/bin/polipo. Other than that, polipo is executing no processes.
I tried adding the following to my iptables rules nat section:
-A OUTPUT -p tcp -m tcp -m owner ! --uid-owner polipo -j ACCEPT
-A OUTPUT -p tcp -m tcp -m owner ! --uid-owner polipo -j REDIRECT --to-ports 9040
polipo now works, but the rest of my traffic that should go to the TransPort gets blocked.
[EDIT]
I'm now trying the same thing, except that I've chained privoxy with polipo like so:
browser > privoxy > polipo > tor > internet
my iptables rules look like this:
# Generated by iptables-save v2.4.15 on Fri Oct 12 16:33:33 2012
*nat
:PREROUTING ACCEPT [12:3420]
:INPUT ACCEPT [1:261]
:OUTPUT ACCEPT [0:0]
:POSTROUTING ACCEPT [0:0]
#-A OUTPUT -p tcp -m tcp -m owner ! --uid-owner tor -j REDIRECT --to-ports 9040
-A OUTPUT -p tcp -m tcp -m owner ! --uid-owner tor -m owner ! --uid-owner polipo -m owner ! --uid-owner privoxy -j REDIRECT --to-ports 9040
COMMIT
# Completed on Fri Oct 12 16:33:33 2012
# Generated by iptables-save v1.4.15 on Fri Oct 12 16:33:33 2012
*filter
:INPUT DROP [9:1175]
:FORWARD ACCEPT [0:0]
:OUTPUT DROP [8:488]
# general
-A OUTPUT -p tcp -m owner --uid-owner tor -j ACCEPT
-A INPUT -m conntrack --ctstate RELATED,ESTABLISHED -j ACCEPT
-A OUTPUT -m conntrack --ctstate RELATED,ESTABLISHED -j ACCEPT
# allow loopback
-A INPUT -i lo -j ACCEPT
-A OUTPUT -o lo -j ACCEPT
-A INPUT -p all -s 127.0.0.1 -d 127.0.0.1 -j ACCEPT
# allow NTPD time syncs
-A OUTPUT -p udp --dport 123 -j ACCEPT
# allow tor
-A OUTPUT -p tcp --dport 9040 -j ACCEPT
-A OUTPUT -p udp --dport 53 -j ACCEPT
-A OUTPUT -p tcp --dport 8123 -j ACCEPT
-A OUTPUT -p tcp --dport 8118 -j ACCEPT
# allow pings
-A OUTPUT -p icmp --icmp-type 8 -j ACCEPT
COMMIT
# Completed on Fri Oct 12 16:33:33 2012
and it STILL won't route traffic right. iptables redirects to the TransPort, but any traffic passed through polipo or privoxy reveals "connection reset" error message. Help?
Last edited by ParanoidAndroid (2013-03-12 01:50:51)

Router stops all traffic randomly, why?

I recently bought a slingbox. My problem has been, since I hooked it up, it constanly broadcast streaming video out to their servers so I can access it from anywhere. Since I installed it, after a few hours of running, it stops transmitting all data. Is there a cap on what it will process outgoing before it stops, and if so, how do I remove that?

hi , what router are u using ? what are your current settings ?? also ensure that u have the latest firmware for the router.

Howto allow all inbound traffic on 678?

I have a 501 behind a 678 (CBOS 2.4.6) The 678 does not allow inbound connection by default. How can I config the 678 to simply terminate the ADSL and allow all traffic both in and out, so that I can let the 501 do all the access control?

Try:
http://www.cisco.com/en/US/products/sw/netmgtsw/ps528/products_user_guide_book09186a008007ce34.html
http://www.cisco.com/en/US/products/sw/netmgtsw/ps528/prod_release_note09186a00800eac45.html

SonicWall SourceNAT VPN setup as default route for all traffic!

Hi,OK hope someone can help with this mess.....Our customer has been taken over by a US company who have said all outgoing internet traffic must go via their data centre. They want us to create an IPSEC vpn from our SonicWALL TZ215 to them then route all traffic locally via this VPN.In principle this didn't sound too bad. Then there were some more options:Our local subnet 172.x.x.x has to be NAT'd to a single /32 address. 192.x.x.131They also require our destination network to be set as 0.0.0.0. as they wont specify the range at the datacenter.I have managed to get the VPN up but using the the NAT address as my local subnet and using the option on the SonicWALL "Use this VPN Tunnel as default route for all Internet traffic" on the remote network. Phase 1 and Phase 2 work ok. The problem i now have is i need to route all LAN traffic...
This topic first appeared in the Spiceworks Community

Hi Norbert,
I am sorry to say that configuring routes in Azure Virtual network is not supported. I recommend you to submit your reuqirement on Azure Feedback and hope it would be released soon:
http://feedback.azure.com/forums/217313-networking-dns-traffic-manager-vpn-vnet
Best regards,
Susie
Please remember to mark the replies as answers if they help and unmark them if they provide no help. If you have feedback for TechNet Subscriber Support, contact [email protected]

Traffic only allowed one-way for VPN connected computers

Hello,
I currently have an ASA 5505. I have set it up as a remote access SSL VPN. My computers can connect to the VPN just fine. They just can't access the internal LAN (192.168.250.0). They can't ping the inside interface of the ASA, or any of the machines. It seems like all traffic is blocked for them. The strange thing is that when someone is connected to the VPN, I can ping that VPN-connect machine from the ASA and other machines inside the LAN. It seems the traffic only allows one way. I have messed with ACL's with no avail. Any suggestions please?
DHCP Pool: 192.168.250.20-50 --> For LAN
VPN Pool: 192.168.250.100 and 192.168.250.101
Outside interface grabs DHCP from modem
Inside interface: 192.168.1.1
Current Running Config:
: Saved
ASA Version 8.2(5)
hostname HardmanASA
enable password ###### encrypted
passwd ####### encrypted
names
interface Ethernet0/0
switchport access vlan 20
interface Ethernet0/1
switchport access vlan 10
interface Ethernet0/2
switchport access vlan 10
interface Ethernet0/3
shutdown
interface Ethernet0/4
shutdown
interface Ethernet0/5
shutdown
interface Ethernet0/6
shutdown
interface Ethernet0/7
switchport access vlan 10
interface Vlan1
no nameif
no security-level
no ip address
interface Vlan10
nameif inside
security-level 100
ip address 192.168.250.1 255.255.255.0
interface Vlan20
nameif outside
security-level 0
ip address dhcp setroute
ftp mode passive
dns domain-lookup inside
dns domain-lookup outside
pager lines 24
mtu inside 1500
mtu outside 1500
ip local pool VPN_Pool 192.168.250.100-192.168.250.101 mask 255.255.255.0
icmp unreachable rate-limit 1 burst-size 1
no asdm history enable
arp timeout 14400
global (outside) 10 interface
nat (inside) 10 192.168.250.0 255.255.255.0
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
aaa authentication ssh console LOCAL
http server enable
http 192.168.250.0 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec security-association lifetime seconds 28800
crypto ipsec security-association lifetime kilobytes 4608000
telnet timeout 5
ssh 192.168.250.0 255.255.255.0 inside
ssh timeout 5
ssh version 2
console timeout 0
dhcpd dns 8.8.8.8
dhcpd address 192.168.250.20-192.168.250.50 inside
dhcpd enable inside
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
enable outside
svc image disk0:/anyconnect-win-2.5.2014-k9.pkg 1
svc image disk0:/anyconnect-macosx-i386-2.5.2014-k9.pkg 2
svc image disk0:/anyconnect-linux-2.5.2014-k9.pkg 3
svc enable
tunnel-group-list enable
group-policy DfltGrpPolicy attributes
dns-server value 8.8.8.8
vpn-tunnel-protocol IPSec l2tp-ipsec svc webvpn
tunnel-group AnyConnect type remote-access
tunnel-group AnyConnect general-attributes
address-pool VPN_Pool
tunnel-group AnyConnect webvpn-attributes
group-alias AnyConnect enable
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect ip-options
inspect netbios
inspect rsh
inspect rtsp
inspect skinny
inspect esmtp
inspect sqlnet
inspect sunrpc
inspect tftp
inspect sip
inspect xdmcp
service-policy global_policy global
prompt hostname context
no call-home reporting anonymous
call-home
profile CiscoTAC-1
no active
destination address http https://tools.cisco.com/its/service/oddce/services/DDCEService
destination address email [email protected]
destination transport-method http
subscribe-to-alert-group diagnostic
subscribe-to-alert-group environment
subscribe-to-alert-group inventory periodic monthly
subscribe-to-alert-group configuration periodic monthly
subscribe-to-alert-group telemetry periodic daily
Cryptochecksum:30fadff4b400e42e73e17167828e046f
: end

Hello,
I seem to be having the same kind of issue although I cannot ping from either end.
Ive set up a l2tp/ipsec vpn which I am able to connect to and get ip from my ip pool (radius authentication is working).
I tried running:
access-list NAT_0 permit ip 192.168.1.0 255.255.255.0 192.168.2.0 255.255.255.0
nat (inside) 0 access-list NAT_0
but i get an error msg saying that the syntax of the nat command is deprecated. Im running ASA version 8.4.
Ive fiddled around abit to find the correct syntax but have been unsuccessfull so far.
Any help would be much appreciated
This is a part of my config:
object network obj_any
subnet 0.0.0.0 0.0.0.0
object network AD1
host 192.168.1.31
description AD/RADIUS
object network NETWORK_OBJ_192.168.1.0_24
subnet 192.168.1.0 255.255.255.0
object network vpn_hosts
subnet 192.168.2.0 255.255.255.0
access-list AD_splitTunnelAcl standard permit 192.168.1.0 255.255.255.0
access-list split-acl standard permit 192.168.1.0 255.255.255.0
access-list inside_nat0_outbound extended permit ip any 192.168.1.0 255.255.255.0
access-list inside_0_outbound extended permit ip object NETWORK_OBJ_192.168.1.0_24 object vpn_hosts
ip local pool POOL2 192.168.2.2-192.168.2.10 mask 255.255.255.0
nat (inside,outside) source static any any destination static NETWORK_OBJ_192.168.1.0_25 NETWORK_OBJ_192.168.1.0_25 no-proxy-arp route-lookup
nat (inside,outside) source static NETWORK_OBJ_192.168.1.0_24 NETWORK_OBJ_192.168.1.0_24 destination static NETWORK_OBJ_192.168.1.0_25 NETWORK_OBJ_192.168.1.0_25 no-proxy-arp route-lookup
nat (inside,outside) source static NETWORK_OBJ_192.168.1.0_24 NETWORK_OBJ_192.168.1.0_24 destination static vpn_hosts vpn_hosts
object network obj_any
nat (inside,outside) dynamic interface
access-group outside_access_in in interface outside
route outside 0.0.0.0 0.0.0.0 ########## 1
no vpn-addr-assign aaa
no vpn-addr-assign dhcp

How to allow a subnet for a number of hosts to surf internet and ping from inside and outside in ASA in GNS3?

after tried to setup access list, it return drop in packet tracer and can not ping outside router too
is there an configuration example to show allow a subnet of class C IP address to surf internet in Cisco ASA ?
assume all works in GNS3, expect initial network setup too
inside outside
router A 192.168.1.2 <--->switch <---> 192.168.1.1 ASA 192.168.1.4 <---> switch <---> router B 192.168.1.3
ASA version: 8.42
when i try the following command,
ASA
conf t
interface GigabitEthernet 0
description INSIDE
nameif inside
security-level 0
ip address 192.168.1.1 255.255.255.0
no shut
end
conf t
interface GigabitEthernet 1
description OUTSIDE
no shutdown
nameif outside
security-level 100
ip address 192.168.1.4 255.255.255.0
no shut
end
conf t
object network obj_any
subnet 0.0.0.0 0.0.0.0
nat (inside,outside) dynamic interface
end
conf t
access-list USERSLIST permit ip 192.168.1.0 255.255.255.0 any
access-group USERSLIST in interface inside
end
Router A
conf t
int fastEthernet 0/0
ip address 192.168.1.2 255.255.255.0
no shut
end
Router B
conf t
int fastEthernet 0/0
ip address 192.168.1.3 255.255.255.0
no shut
end
ASA-1# packet-tracer input inside tcp 192.168.1.1 1 192.168.1.4 1
Phase: 1
Type: ROUTE-LOOKUP
Subtype: input
Result: ALLOW
Config:
Additional Information:
in 192.168.1.0 255.255.255.0 inside
Phase: 2
Type: ACCESS-LIST
Subtype:
Result: DROP
Config:
Implicit Rule
Additional Information:
Result:
input-interface: inside
input-status: up
input-line-status: up
output-interface: inside
output-status: up
output-line-status: up
Action: drop
<--- More --->

current config can not ping, one of packet tracer allow all, another packet tracer drop
can not ping between Router A and Router B
ASA-1# packet-tracer input inside tcp 192.168.1.2 1 192.168.3.3 1
Phase: 1
Type: ROUTE-LOOKUP
Subtype: input
Result: ALLOW
Config:
Additional Information:
in 192.168.3.0 255.255.255.0 outside
Phase: 2
Type: IP-OPTIONS
Subtype:
Result: ALLOW
Config:
Additional Information:
Phase: 3
Type: NAT
Subtype:
Result: ALLOW
Config:
object network DYNAMIC-PAT
nat (inside,outside) dynamic interface
Additional Information:
Dynamic translate 192.168.1.2/1 to 192.168.3.4/311
<--- More --->
<--- More --->
Phase: 4
<--- More --->
Type: IP-OPTIONS
<--- More --->
Subtype:
<--- More --->
Result: ALLOW
<--- More --->
Config:
<--- More --->
Additional Information:
<--- More --->
<--- More --->
Phase: 5
<--- More --->
Type: FLOW-CREATION
<--- More --->
Subtype:
<--- More --->
Result: ALLOW
<--- More --->
Config:
<--- More --->
Additional Information:
<--- More --->
New flow created with id 14, packet dispatched to next module
<--- More --->
<--- More --->
Result:
<--- More --->
input-interface: inside
<--- More --->
input-status: up
<--- More --->
input-line-status: up
<--- More --->
output-interface: outside
<--- More --->
output-status: up
<--- More --->
output-line-status: up
<--- More --->
Action: allow
<--- More --->
ASA-1# packet-tracer input outside tcp 192.168.3.3 1 192.168.1.2 1
Phase: 1
Type: ROUTE-LOOKUP
Subtype: input
Result: ALLOW
Config:
Additional Information:
in 192.168.1.0 255.255.255.0 inside
Phase: 2
Type: ACCESS-LIST
Subtype:
Result: DROP
Config:
Implicit Rule
Additional Information:
Result:
input-interface: outside
input-status: up
input-line-status: up
output-interface: inside
output-status: up
output-line-status: up
Action: drop
<--- More --->
Drop-reason: (acl-drop) Flow is denied by configured rule
<--- More --->
ASA-1#
ASA-1# sh run |
: Saved
ASA Version 8.4(2)
hostname ASA-1
enable password 8Ry2YjIyt7RRXU24 encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
names
interface GigabitEthernet0
description INSIDE
nameif inside
security-level 100
ip address 192.168.1.1 255.255.255.0
interface GigabitEthernet1
description OUTSIDE
nameif outside
security-level 0
ip address 192.168.3.4 255.255.255.0
interface GigabitEthernet2
shutdown
no nameif
no security-level
<--- More --->
no ip address
<--- More --->
<--- More --->
ftp mode passive
<--- More --->
object network DYNAMIC-PAT
<--- More --->
subnet 192.168.1.0 255.255.255.0
<--- More --->
access-list 101 extended permit icmp any any echo-reply
<--- More --->
access-list 101 extended permit icmp any any source-quench
<--- More --->
access-list 101 extended permit icmp any any unreachable
<--- More --->
access-list 101 extended permit icmp any any time-exceeded
<--- More --->
access-list ACL-OUTSIDE extended permit icmp any any
<--- More --->
pager lines 24
<--- More --->
mtu inside 1500
<--- More --->
mtu outside 1500
<--- More --->
icmp unreachable rate-limit 1 burst-size 1
<--- More --->
no asdm history enable
<--- More --->
arp timeout 14400
<--- More --->
<--- More --->
object network DYNAMIC-PAT
<--- More --->
nat (inside,outside) dynamic interface
<--- More --->
access-group ACL-OUTSIDE in interface outside
<--- More --->
timeout xlate 3:00:00
<--- More --->
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
<--- More --->
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
<--- More --->
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
<--- More --->
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
<--- More --->
timeout tcp-proxy-reassembly 0:01:00
<--- More --->
timeout floating-conn 0:00:00
<--- More --->
dynamic-access-policy-record DfltAccessPolicy
<--- More --->
user-identity default-domain LOCAL
<--- More --->
no snmp-server location
<--- More --->
no snmp-server contact
<--- More --->
snmp-server enable traps snmp authentication linkup linkdown coldstart warmstart
<--- More --->
telnet timeout 5
<--- More --->
ssh timeout 5
<--- More --->
console timeout 0
<--- More --->
threat-detection basic-threat
<--- More --->
threat-detection statistics access-list
<--- More --->
no threat-detection statistics tcp-intercept
<--- More --->
<--- More --->
<--- More --->
prompt hostname context
<--- More --->
no call-home reporting anonymous
<--- More --->
call-home
<--- More --->
profile CiscoTAC-1
<--- More --->
no active
<--- More --->
destination address http https://tools.cisco.com/its/service/oddce/services/DDCEService
<--- More --->
destination address email [email protected]
<--- More --->
destination transport-method http
<--- More --->
subscribe-to-alert-group diagnostic
<--- More --->
subscribe-to-alert-group environment
<--- More --->
subscribe-to-alert-group inventory periodic monthly
<--- More --->
subscribe-to-alert-group configuration periodic monthly
<--- More --->
subscribe-to-alert-group telemetry periodic daily
<--- More --->
crashinfo save disable
<--- More --->
Cryptochecksum:8ee9b8e8ccf0bf1873cd5aa1efea2b64
<--- More --->
: end
ASA-1#

I have qualitynet either wired internet. I buy a card good for a month at a time, I can only log into one device at any one time. Are there settings I can adjust on my airport express to allow all my devices to connect to wi-fi without having to log out.

I have qualitynet either wired internet. I buy a card good for a month at a time, I can only log into one device at any one time. Are there settings I can adjust on my airport express to allow all my devices to connect to wi-fi without having to log out of one devise before using another?

Some Internet providers that limit access to a single device at a time do so by the device's hardware MAC address. If your ISP is one of those, you may be able to substitute the MAC address of your AirPort Express base station for the computer. I would suggest that you contact them to find out if this is allowable.

Can't get around this error after adding second dataset...A scope is required for all aggregates used outside of a data region unless the report contains exactly one dataset

I added a dataset to an existing report and broke an aggregation. In the old (i.e. single dataset) report, this expression below worked fine. I wanted to get a distinct count of the vst_ext_id field when my educated field was like "VTE1*"
= CountDistinct(IIF(Fields!educated.Value like "VTE1*", Fields!vst_ext_id.Value, Nothing))
After adding a new dataset, this no longer works and I get the error " A scope is required for all aggregates used outside of a data region unless the report contains exactly one dataset". Having done some research online, I found that I
needed to specify my dataset explicitly and I thought this new expression might work, but still no success...
= CountDistinct(IIF(Fields!educated.Value,"DataSet1" like "VTE12*", Fields!vst_ext_id.Value,"DataSet1", Nothing))
Am I missing something? Based on online responses, this explicit dataset naming convention seems to help most people, but it isn't working for me.
Thanks in advance!
Brian

I found the answer. Apparently, my expression syntax was off. This expression does the trick...
= CountDistinct(IIF(Fields!educated.Value like "VTE12*", Fields!vst_ext_id.Value,Nothing),"DataSet1")
I just happened upon this particular syntax searching online. I was trying to specify the dataset name after each .value, but I never got that to work. This is the only time I have found this particular syntax online.

Not allowing to query for all blocks.

hi,
i have a new question.
I'm not able to query in all the fields of all blocks.
I'm able to query only in all fields of master-block. But not able to query in fields of other blocks.
I have set 'query all records' in the property palette to 'Yes'.
What should i do do allow it query & execute in all fields of all blocks?
Thank you.

Pl do not post duplicates - Not allowing to query for all blocks.

How I can allow always and for all sites full-screen mode?

How I can allow always and for all sites full-screen mode?
And I want choose anywhere option "never show notification about full-screen mode" (screenshot attached)
RUS
Как я могу всегда разрешить и для всех сайтов полноэкранный режим?
И я хочу выбрать где-нибудь опцию "никогда не показывать уведомление о полноэкранном режиме" (скриншот приложен)

There is a preference setting on the <b>about:config</b> page that is meant for developers and testers to make this possible, but it is not meant for normal users.
*full-screen-api.approval-required = false
You can open the <b>about:config</b> page via the location/address bar.
You can accept the warning and click "I'll be careful" to continue.
*http://kb.mozillazine.org/about:config

RV016 Router Allow All Traffic For Outside IP

Similar Messages

Maybe you are looking for