RV042G web console locks up when changing log settings (4.2.2.08)

Anyone experiencing this issue ? Seems that when I change a log setting like enabling Incoming Log, I can logout but can no longer log in. The web interface hans after logging in and eventually times out. The only workaround is to reboot the router.
I'm running the latest FW 4.2.2.08.

Anyone experiencing this issue ? Seems that when I change a log setting like enabling Incoming Log, I can logout but can no longer log in. The web interface hans after logging in and eventually times out. The only workaround is to reboot the router.
I'm running the latest FW 4.2.2.08.

Similar Messages

  • My computer locks up when i log out

    my computer locks up when i log out

    I had the same proplem with my I-Pod and any mp3 I would plug in. I have 4 usb ports on my pc and only one is a usb 2.0. I tried each one until I found it and my pc did not freeze and it is charging right now as I am typing.
    Steps
    1. right click my computer
    2. click properties
    3. click hardware
    4. click device manager
    5. double click universal Serial buss controllers
    6. depending how many usb root hubs, hopefully you have one that says USB 2.0 Root Hub
    that is the usb port you have to locate and use
    If that does not work try updating the drivers by double clicking USB 2.0 Root Hub and follow instructions.
    I have Windows xp and windows 2000 on this PC and I am using 2000 Primarily. The steps might be a little diff. with XP but it should be close. I'd have to reboot into XP to see.
    Good Luck

  • Computer freezes when changing wireless settings

    I first noticed this in a café last week, and now it's doing it 100% of the time.
    It seems that whenever I try to change the settings on my wireless connection, the computer will freeze. Mouse won't move, video doesn't update, nothing. I have to do a hard reset (press the power button for a few seconds until the computer restarts). If the wireless connection is active, the computer will freeze soon after reboot. If the wireless connection is off, no problem.
    Here's a list of the things I've tried:
    - Fix hard drive permissions. No luck.
    - Repair hard drive after booting from Snow Leopard DVD. Still freezes.
    - I booted the computer from the OS DVD. I looked into the wireless menu and, again, it froze.
    - I opened the computer and put the original memory in it. Still freezes.
    I have to admit I am at a loss here. I'm going to a client site next week and I don't mind looking like an idiot because I can't use wireless on my computer, but it's still incredibly annoying.
    Any ideas?
    Thanks in advance!

    cmd-opt-n-v (Clear NV RAM) may help you.
    Also, "Repair Disk Permissions" from Disk Utility may help.
    Last, have you installed the latest update (10.4.6)?
    Mihalis.

  • PC Health in BIOS freezes when changing fan settings

    Hello everyone. I seem to be having a problem with my K8n Diamond plus board. Whenever i try to go into the PC health to change fan settings the bios seems to freeze up and i have to press reset to get out. Is there a bios flash that can fix the problem? Any replys would be much appreciated 

    Try to change values by using the + & - keys on the numeric side of the keyboard or using PageUp & PageDown keys once
    you have the item in cmos highlighted. Dont hit enter on the cmos item .
    There has been several bios bugs over time that halts bios on certain items if using enter on it (fault in the list range of the items).
    Workaround for theese has been to scroll the value with +/- or PgUp/PgDwn keys.

  • IOS IPS -- SDM locks up when changes applied

    Has anyone encountered the situation in the IPS section of SDM where you click on the "apply changes" button after editing some signatures and the SDM applet never finishes from applying the changes.
    If I make more than just a few signature deletes or modifications this seems most likely to happen. And not just across a WAN either, I also have experienced it when the router is directly connected to my PC. The browser freezes up, sometimes I get a popup message that "SDM has lost connection to the Router".
    Certainly it's unnerving when I make changes to a remote site, I get visions of the Router locking up and me having to jump into the car for an overnight drive so that I can be at some branch office when they open in the morning.

    The simplest and perhaps the first thing I would verify is that you do not have multiple PopUp Blockers running on your PC/Laptop. If you do...turn them off temporarily.
    When I run into issues like this with any Java applet based management interface I always make sure that the required version of the JRE is installed and in the control panel the only active JRE to be used by the browser. The other thing you need to check, and possibly update is the version of SDM that you have running on the routers. Make sure you have the latest and most bug free version. So, to recap...verify your JRE and update your SDM version if necessary. I hope this helps.

  • [Forum FAQ]Solution for Windows PowerShell console font issue when changing system locale

    Issue description
    After changing Windows System Locale to another country, users cannot modify Windows PowerShell console font to Lucida after modifying the font settings. There is also a potential bug report in Microsoft connect:
    https://connect.microsoft.com/PowerShell/feedback/details/806286/powershell-4-console-font-issue
    Reason
    In most situations, this problem is caused by system locale is changed to other countries from United States, such as Chinese, French, etc. Because of this change, the code page and font of Windows PowerShell console might be changed with system locale.
    For Example, if change system locale to Chinese (Simplified China), Windows PowerShell console
    (%systemdrive%\ProgramData\Microsoft\Windows\Start Menu\Programs\System Tools) properties would be changed like this:
    Solution
    To resolve this problem, please follow the steps below:
    Access to the path below to find the shortcut of Windows PowerShell:
    %systemdrive%\ProgramData\Microsoft\Windows\Start Menu\Programs\System Tools.
    Right click Windows PowerShell and choose Properties.
    Switch to Options, check if Current code page list there, if that it is, choose
    437 (OEM-United States) and click Apply. Maybe you will encounter an
    Access Deniedpop-up as the following picture.  Then you need take ownership of current PowerShell File, switch to
    Security Tab and obtain full control permission for current User Account.
    Note: if Current code page was not list there, just leave alone
    Options settings and switch to Font Tab.
    Switch to Font Tab, choose the font you wished to use, click
    Apply.
    After the above settings, current Windows PowerShell console font should works as you wished.
    Applies to
    Windows PowerShell 3.0
    Windows PowerShell 4.0
    Please click to vote if the post helps you. This can be beneficial to other community members reading the thread.

    Cause
    This issue is due to the bootmgr file, we cannot use the bootmgr file of Windows 7 to find the Windows 8 Operating System files.
    The Windows 7 bootmgr can indeed boot Windows 8.
    This is on a BIOS system 
    https://www.youtube.com/watch?v=AVO5aeaKeeE
    This is on a UEFI system 
    https://www.youtube.com/watch?v=g3-K6Fyobz0
    The Windows 8 bootmgr partially loads Windows 8 before offering the boot menu.  By choosing Windows 7, the system must do a reboot.  Using the Windows 7 bootmgr, no reboot is required.
    "Let them that don't want it have memories of not gettin' any." "Gratitude is riches and complaint is poverty and the worst I ever had was wonderful." Brother Dave Gardner. "Experience is what you get when you're looking for something
    else." Sir Thomas Robert Deware

  • Web page locks up when running Java

    I downloaded the java program that Ameritrade told me to download to run their Streamer product, but when I try to run the product, it locks up the web page.

    Poor baby, so go whine to Ameritrade!

  • Apply button not working when changing AP settings

    Hi Guys,
    I am working on installing a new 2500 Controller with 2 AIR-LAP1242G's attached to it.  I have both registered and on the controller but I am having trouble moving one of them to a new IPS AP group that I created.  Furthermore, I noticed the default gateway is missing from the static ip settings and I am unable to add that as well.  When I add the default gateway and hit apply, the controller does nothing. Same thing for when I try to change my WIPS device to monitor mode.  Has anyone ever seen behaivor like this?
    A couple other things that I noticed is that when I go to AP groups and try to remove the AP's from the default group, there is no remove button when you go inside the default group like  I see when i go into my IPS group.
    The AP's are on software ver 12.4(23c)JA3 Boot ver 12.4.13.0
    and the controller is at 7.0.22.0
    I have already power cycled the controller and both AP's.  Is there anything else that anyone can think to look at here?

    Grrr.....I tried everything but closing the browser out and opening a new session.  I logged out and back in without closing internet explorer completely but it turned out closing internet explorer solved this.

  • "could not load any writer" when changing render settings?

    When I change my render output settings from Quicktime Movie to something like H.264, I get an error saying "could not load any writer, adobe media encoder will now exit". Does anyone know how to fix this?
    When I select Quicktime Movie then change the compression type to H.264, After Effects then tells me "for reliable output with H.264 compression, please choose it directly fro the Output Module..." which then puts me right back where I started with this posting.
    Any suggestions?
    Thanks!
    Kristin.

    @Kevin: The MPEG stuff being defunct should not affect fresh installs. So it's definitely some other app "stealing" the CoDecs. In what order are you installing? Perhaps having Nero, some DVD-player software or something similar inbetween? Did you deactivate the products before re-installing? what formatting options did you choose?
    @kristin: As Jonas said, check QT. In addition, I would attempt yet another re-install, but this time taking care to really manually survey the progress. I'm suspecting that some of your files never get overwritten, so the config issue remains in place and your modules don't show up. So deactivate the app, uninstall it, run the CS3 clean scripts. Before re-installing, check your Library/Application Support/Adobe directory and the Preferences directory. Rip out any pieces that look suspicious and may be related to After Effects or Premiere/Encore, in particular MediaCore. Furthermore, remove any installer logs and remnants in the respective directories (Library/Logs, library/Application Support/Adobe/Installers). The packages are recognizable by their icon and the logs have the respective names of the product.
    Mylenium

  • Hotsynch Abnormally Terminates when changing default settings - Treo 700p

    I recently purchased a Sprint Treo 700p. I installed Hotsync from the CD and successfully synchronized with my Outlook 2003 (front end to Exchange 2003) Contact and Calendar folders. After several days, I noticed that it no longer synchronized those 2 folders. When I looked at the "Custom" setup, I noticed that the setting for Calendar and Contacts was "Do Nothing", which was not what I had originally selected. When I attempted to change the default to "Synchronize", I receive a message from Windows that the HotSync Manager Application has encountered a problem and needs to close. In addition, there is an entry placed in the Event Log, "Faulting application hotsync.exe, version 6.0.1.0, faulting module hotsync.exe, version 6.0.1.0, fault address 0x0002d94f.". I don't even have to hit the synch button to get it to fail. I have tried uninstalling and reinstalling to no avail. I even uninstalled, deleted the subdirectory on my hard drive, and deleted the registry entries as well. In addition, I have tried it with Exchange cached mode and non-cached mode. It fails both ways. I can no longer synchronize my Calendar and Contacts, which is one of the reasons I purchased the Treo 700p in the first place. Please help.
    Post relates to: Treo 700p (Verizon)

    Folks, I have exactly the same issue with a Sprint 700p. I am communicating with someone on this support site who is trying to help me out, but so far, we have not made progress. Has anyone found a resolution? I am currently carrying around a paper copy of my address book!!
    Post relates to: Treo 700p (Sprint)

  • Exception when changing Variable Settings in 7.x WebTemplate

    Hi,
    We are trying to execute the query on the Web using 7.0x web template (2004s Netweaver) . Sometimes NullPointerException is thrown when we are trying to change the Properties of Characteristic Version of a variable in Variable Selection Screen using the Settings button (This button is present in the Select Values screen). And sometimes this works fine, i.e. Settings screen opens up and we are able to change the Characteristic property.
    Is anyone else facing similar kind of issue? And what is the possible fix for this issue?
    Thanks in Advance

    Hi,
        Use Current Calender day(0DAT) variable and due date(not required) take it as optional.
    Regards
    Pcrao.

  • ITunes 10.6 freezes when changing sync settings

    Update to iTunes 10.6 on Windows 7 computer today.  Now when I try to change my sync settings, and hit "apply" - iTunes freezes and the sync does not complete.  I have already tried to factory reset the iPod Nano, and tried to totally uninstall and reinstall iTunes.  Any other suggestions?

    Uninstall/Reinstall did not work. Same issue with freezing as soon as it's launched.
    Just to confirm, this is 10.6.3 64-bit Windows build.

  • Macbook locked.  Cannot change security settings

    I have a macbook that is password locked (we can't remember the password) and the security setup will not let me create an admin account to change users and / or settings.  How can I rebuild the computer to eliminate the user and change the security settings?  I can get to settings as long as I don't shut down the computer, but I can't change anything without a password.  So far I have been leaving in sleep mode which does not require me to enter the password.

    You can get replacement System Install & Restore CD/DVDs from Apple's Customer Support - in the US, (800) 767-2775 - for a nominal S&H fee. You'll need to have the model and/or serial number of your Mac available.
    If you're not in the US, you may need to go through the regional Apple Store that serves your location to find the contact number. Here's a list of links to all of those - http://store.apple.com/Catalog/US/Images/intlstoreroutingpage.html  Another resource:  International Support Phone #s.
    can I boot from dvd and rebuild the computer?
    I don't see how, since you stated you do not have them.

  • Crash when changing color settings

    InDesign CS3 5.0.3.
    4 machines. 3 are exactly the same hardware-wise with 10.4x. 1 is new with 10.5x.
    I'm changing the color settings for CS3. I put new .csf and .icc files in their proper libraries.
    I change PS color settings on all. Happy happy.
    I change the Bridge "Creative Suite Color Settings" on all. Happy happy.
    2 machines (both 10.4x)--InDesign opens/works fine. The other two don't want to have anything to do with this new color settings---crash crash crash. Delete color settings preference and all is well.
    The situation is the same if I DON'T change the "creative suite color settings" in Bridge and try to change the color settings only in INDD.
    Has anyone else run into something similar?
    Thanks
    Corey Frix

    David,
    i am using flash cs3 on a macbook pro and have never had such issue.
    i would contact adobe about it.  They have excellent support.  i have called them on other issues and i always get very professional service.
    Good luck, Braulio

  • Unable to log into the user management administration web console

    Can someone tell how resolve my ablity to log into the user management administration web console? I can't log into SAP Netweaver Admin,  User managment, and Webdynpro content Administrator and Web Dynpro Consol. But able active j2ee engine sample? Is there some that I need activate to allow me log in? 
    http://localhost:50000/logon/logonServlet?redirectURL=%2Fuseradmin%2FuserAdminServlet%3FgotoDefaultPage%3D.

    Hi,
    I had this problem also. For me it worked to log on to the SLD and then I was able to log on to the other applications like Useradmin and NWA.
    The SLD is usually available at <a href="http://localhost:50000/sld">http://localhost:50000/sld</a>.
    Regards,
    Sebastian

Maybe you are looking for