RV220W not finding "known to be existing" value -- SNMPv3 protocol

Hello - just looking for some guidance perhaps here?
What would make a Cisco RV220W router fail to provide an "known to be existing" value only when it is queried 'remotely' using SNMPv3 protocol?
It is "known to be existing" because an SNMPv1 (and SNMPv2c) query works fine.
The 'remote' SNMPv3 query seems to gain access but then report that the value does not exist.
I can find no RV220W logging information regarding the remote access attempt - even though DEBUGGING is on ....
Does SNMP slip in without being logged?
ADVthanksANCE,
michael grimes
Summary:
========
We have four (4) similar RV220W routers, each in a different location.
Three of them are responding well to SNMPv3 AuthNoPriv queries.
One gives us a "Timeout (Sub-id not found: ..."
It must be some kind of setting on this "odd" RV220W.
My question is where else might I look.
(1) credentials appear to be same
(2) SNMPv3 configuration seems to be correct (identical configuration works for different RV220W)
DETAILS:
========
michael@CRCC-ltMRG /cygdrive/c/users/michael/Downloads
$ snmpwalk -v 1 -m ALL -c CRG <<valid-routable-IPadress>> SysLocation
SNMPv2-MIB::sysLocation.0 = STRING: WorcCRG
michael@CRCC-ltMRG /cygdrive/c/users/michael/Downloads
$
{ so above you see that the entry exists }
michael@CRCC-ltMRG /cygdrive/c/users/michael/Downloads
$ snmpwalk -v 3 -m ALL -u cisco -l AuthNoPriv -a MD5 -A <<valid-MD5passphrase>> <<valid-routable-IPaddress>> SysLocation
snmpwalk: Timeout (Sub-id not found: (top) -> SysLocation)
michael@CRCC-ltMRG /cygdrive/c/users/michael/Downloads
$
{ so above you see that the RV220W complains that the entry does not exist }
Also note that if the same SNMPv3 command is run from 'inside' the RV220W IPsapce we get the same (good) result as if using the SNMPv1 query.

It appears that this is a bug in CF8 - I moved my code over to a CF9 box, and it ran with no errors.
-reed

Similar Messages

Spotlight not finding files that definitely exist.

I have spent the day backing up and syncing.
I have an epson P4000 (PSD). I also have two external drives (yes, this may be overkill, but I never do it). The P4000 is backed up and synced to both drives.
When I do a search for all files with a .RAW extension in the three places, the P4000 and one drive find all the files (2798) but the other drive only shows 602 files.
I know the files are there. Why isn't spotlight finding them? How can I make it find them?
Thanks for any info.

The Spotlight index may not be up to date for that drive.
You can force Spotlight to re-index any drive (including the drive you boot from) by opening System Preferences / Spotlight / Privacy and dragging the icon for the drive into Privacy.
Then close System Preferences, and I believe you may need to log out and log back in again.
Then go back into System Preferences / Spotlight / Privacy and select the drive now in the Privacy list and click the "-" at the bottom of the list to remove it from the list. Whenever an item is removed from the Privacy list, Spotlight immediately sets out to index it.
You can tell if Spotlight is indexing by clicking on the Spotlight icon in the menu bar. If it is indexing it will state that along with an estimate of how long it has to go.
Also note that if any of your files have the System or Hidden attributes the normal Spotlight search results pulldown won't show them. But you can still find them using the other interface to Spotlight in the Finder.
Open a Finder window and type Command-f to bring up the search criteria lines. In the second line, click on the "kind" drop down and select "other" from the list. A panel will show up giving all the various possible search criteria. The two of interest for finding such files are System Files and File Invisibility. If you check the check box to the right of any lines in that panel those search items will be added to the "kind" drop down list so that you don't have to go back through "other" to select them in the future. The drop down just to the right of the "kind" drop down specifies the rule to apply to that search criteria. So if you select System Files in the first drop down, you also need to select "Include" in the second drop down to see those files in the search results.
--Bob

Resolved: setCurrentRowWithKeyValue not finding row known to exist

Hi, I am trying to set the first master record of a master/detail screen via the setCurrentRowWithKeyValue action in the pageDef via a Session scoped management bean:
<executables>
<iterator id="UsersView1_1Iterator" RangeSize="10" Binds="UsersView1_1"
DataControl="AppModuleDataControl"/>
<iterator id="TasksView1_3Iterator" RangeSize="10" Binds="TasksView1_3"
DataControl="AppModuleDataControl"/>
<variableIterator id="variables">
<variable Type="int" Name="getUserId_return" IsQueriable="false"
IsUpdateable="0" DefaultValue="${bindings.getUserId.result}"/>
</variableIterator>
<invokeAction id="loadUser" Binds="setCurrentRowWithKeyValue"/>
</executables>
<bindings>
<action IterBinding="UsersView1_1Iterator" id="setCurrentRowWithKeyValue"
InstanceName="AppModuleDataControl.UsersView1_1"
DataControl="AppModuleDataControl" RequiresUpdateModel="false"
Action="98">
<NamedData NDName="rowKey" NDValue="${sessionScope.UserInfo.userId}"
NDType="java.lang.String"/>
</action>
based on the error message :
JBO-25020: View row of key oracle.jbo.Key[7 ] not found in UsersView1_1Iterator.
It seems to be using the correct Primary key but not finding its record.
If anyone can help me figure this out, I would greatly appreciate it. Thanks.
Message was edited by:
N8NDREW

I figured this one out myself, two "key" concerns:
From: Oracle® Application Development Framework
Developer’s Guide For Forms/4GL Developers
10g Release 3 (10.1.3.0)
B25947-01
"In order to successfully be able to use the findByKey() method on a read-only view
object, you need to perform two additional steps:
1. Ensure that at least one attribute in the view object has the Key Attribute property
set
2. Enable a custom Java class for the view object, and override its create() method
to call setManageRowsByKey(true)after calling super.create() like this:
// In custom Java class for read-only view object
public void create() {
super.create();
setManageRowsByKey(true);
Doing #2 in my view impl resolved my issue.
Be aware that the RangeSize property might need to be set to -1 as well.

The system could not find a javax.ws.rs.ext.MessageBodyWriter or a DataSourceProvider class for the com.rest.assignment.EmpBean type and application/json mediaType. Ensure that a javax.ws.rs.ext.MessageBodyWriter exists in the JAX-RS application for the

Hi,
Im trying to create a Rest WS with a @GET method that will return me an Emp object. I need the output as a JSON string.
I have created a dynamic web project and added javax RS jars:
When im trying to run this, i'm getting the below mentioned error:
FlushResultHa E org.apache.wink.server.internal.handlers.FlushResultHandler handleResponse The system could not find a javax.ws.rs.ext.MessageBodyWriter or a DataSourceProvider class for the com.rest.assignment.EmpBean type and application/json mediaType. Ensure that a javax.ws.rs.ext.MessageBodyWriter exists in the JAX-RS application for the type and media type specified.
RequestProces I org.apache.wink.server.internal.RequestProcessor logException The following error occurred during the invocation of the handlers chain: WebApplicationException (500 - Internal Server Error)
Please help as im stuck with this from long.
Thanks in advance.
Below is the code for my service class:
package com.rest.assignment;
import java.io.FileInputStream;
import java.io.FileNotFoundException;
import java.io.IOException;
import java.util.Enumeration;
import java.util.HashSet;
import java.util.Properties;
import java.util.Set;
import javax.ws.rs.GET;
import javax.ws.rs.Path;
import javax.ws.rs.Produces;
import javax.ws.rs.core.Application;
import javax.ws.rs.core.MediaType;
import javax.ws.rs.core.Response;
@Path("/restService")
public class RestService extends Application {
    @GET
    @Path("/getEmpDetails")
    @Produces(MediaType.APPLICATION_JSON)
    public Response getStringResponse()
        EmpBean empBean = new EmpBean();
        String filePath = "C:/Program Files/IBM/workspace/HelloWorld/src/com/rest/resources/EmpData.properties";
        Properties properties = new Properties();
        try {
            properties.load(new FileInputStream(filePath));
        } catch (FileNotFoundException e) {
            e.printStackTrace();
        } catch (IOException e) {
            e.printStackTrace();
         Enumeration e = properties.propertyNames();
         String result="";
        String[] empDetailsArr;
        while (e.hasMoreElements()) {
          String key = (String) e.nextElement();
          String empDetails = properties.getProperty(key);
          empDetailsArr=empDetails.split(",");
          empBean.setFirstName(empDetailsArr[0]);
          empBean.setLastName(empDetailsArr[1]);
          empBean.setEmpId(empDetailsArr[2]);
          empBean.setDesignation(empDetailsArr[3]);
          empBean.setSkillSet(empDetailsArr[4]);
          result = empDetailsArr[1];
        //return empBean;
        return Response.ok(empBean).type(MediaType.APPLICATION_JSON_TYPE).build();
    @Override
    public Set<Class<?>> getClasses() {
        Set<Class<?>> classes = new HashSet<Class<?>>();
        classes.add(RestService.class);
        classes.add(EmpBean.class);
        return classes;
and my empBean goes like this:
package com.rest.assignment;
public class EmpBean {
    private String firstName;
    private String lastName;
    private String empId;
    private String designation;
    private String skillSet;
    public String getFirstName() {
        return firstName;
    public void setFirstName(String firstName) {
        this.firstName = firstName;
    public String getLastName() {
        return lastName;
    public void setLastName(String lastName) {
        this.lastName = lastName;
    public String getEmpId() {
        return empId;
    public void setEmpId(String empId) {
        this.empId = empId;
    public String getDesignation() {
        return designation;
    public void setDesignation(String designation) {
        this.designation = designation;
    public String getSkillSet() {
        return skillSet;
    public void setSkillSet(String skillSet) {
        this.skillSet = skillSet;
Web.xml goes like this:
<?xml version="1.0" encoding="UTF-8"?>
<web-app id="WebApp_ID" version="3.0" xmlns="http://java.sun.com/xml/ns/javaee" xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xsi:schemaLocation="http://java.sun.com/xml/ns/javaee http://java.sun.com/xml/ns/javaee/web-app_3_0.xsd">
<display-name>restWS</display-name>
<welcome-file-list>
<welcome-file>index.html</welcome-file>
<welcome-file>index.htm</welcome-file>
<welcome-file>index.jsp</welcome-file>
<welcome-file>default.html</welcome-file>
<welcome-file>default.htm</welcome-file>
<welcome-file>default.jsp</welcome-file>
</welcome-file-list>
<servlet>
<servlet-name>REST</servlet-name>
<servlet-class>com.ibm.websphere.jaxrs.server.IBMRestServlet</servlet-class>
<init-param>
   <param-name>javax.ws.rs.Application</param-name>
   <param-value>com.rest.assignment.RestService</param-value>
</init-param>
<load-on-startup>1</load-on-startup>
</servlet>
<servlet-mapping>
<servlet-name>REST</servlet-name>
<url-pattern>/rest/*</url-pattern>
</servlet-mapping>
</web-app>
When i try to return a string from my get method, it gives me a proper response. i get this exception when im trying to return a JSON response.

Hi,
Im trying to create a Rest WS with a @GET method that will return me an Emp object. I need the output as a JSON string.
I have created a dynamic web project and added javax RS jars:
When im trying to run this, i'm getting the below mentioned error:
FlushResultHa E org.apache.wink.server.internal.handlers.FlushResultHandler handleResponse The system could not find a javax.ws.rs.ext.MessageBodyWriter or a DataSourceProvider class for the com.rest.assignment.EmpBean type and application/json mediaType. Ensure that a javax.ws.rs.ext.MessageBodyWriter exists in the JAX-RS application for the type and media type specified.
RequestProces I org.apache.wink.server.internal.RequestProcessor logException The following error occurred during the invocation of the handlers chain: WebApplicationException (500 - Internal Server Error)
Please help as im stuck with this from long.
Thanks in advance.
Below is the code for my service class:
package com.rest.assignment;
import java.io.FileInputStream;
import java.io.FileNotFoundException;
import java.io.IOException;
import java.util.Enumeration;
import java.util.HashSet;
import java.util.Properties;
import java.util.Set;
import javax.ws.rs.GET;
import javax.ws.rs.Path;
import javax.ws.rs.Produces;
import javax.ws.rs.core.Application;
import javax.ws.rs.core.MediaType;
import javax.ws.rs.core.Response;
@Path("/restService")
public class RestService extends Application {
    @GET
    @Path("/getEmpDetails")
    @Produces(MediaType.APPLICATION_JSON)
    public Response getStringResponse()
        EmpBean empBean = new EmpBean();
        String filePath = "C:/Program Files/IBM/workspace/HelloWorld/src/com/rest/resources/EmpData.properties";
        Properties properties = new Properties();
        try {
            properties.load(new FileInputStream(filePath));
        } catch (FileNotFoundException e) {
            e.printStackTrace();
        } catch (IOException e) {
            e.printStackTrace();
         Enumeration e = properties.propertyNames();
         String result="";
        String[] empDetailsArr;
        while (e.hasMoreElements()) {
          String key = (String) e.nextElement();
          String empDetails = properties.getProperty(key);
          empDetailsArr=empDetails.split(",");
          empBean.setFirstName(empDetailsArr[0]);
          empBean.setLastName(empDetailsArr[1]);
          empBean.setEmpId(empDetailsArr[2]);
          empBean.setDesignation(empDetailsArr[3]);
          empBean.setSkillSet(empDetailsArr[4]);
          result = empDetailsArr[1];
        //return empBean;
        return Response.ok(empBean).type(MediaType.APPLICATION_JSON_TYPE).build();
    @Override
    public Set<Class<?>> getClasses() {
        Set<Class<?>> classes = new HashSet<Class<?>>();
        classes.add(RestService.class);
        classes.add(EmpBean.class);
        return classes;
and my empBean goes like this:
package com.rest.assignment;
public class EmpBean {
    private String firstName;
    private String lastName;
    private String empId;
    private String designation;
    private String skillSet;
    public String getFirstName() {
        return firstName;
    public void setFirstName(String firstName) {
        this.firstName = firstName;
    public String getLastName() {
        return lastName;
    public void setLastName(String lastName) {
        this.lastName = lastName;
    public String getEmpId() {
        return empId;
    public void setEmpId(String empId) {
        this.empId = empId;
    public String getDesignation() {
        return designation;
    public void setDesignation(String designation) {
        this.designation = designation;
    public String getSkillSet() {
        return skillSet;
    public void setSkillSet(String skillSet) {
        this.skillSet = skillSet;
Web.xml goes like this:
<?xml version="1.0" encoding="UTF-8"?>
<web-app id="WebApp_ID" version="3.0" xmlns="http://java.sun.com/xml/ns/javaee" xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xsi:schemaLocation="http://java.sun.com/xml/ns/javaee http://java.sun.com/xml/ns/javaee/web-app_3_0.xsd">
<display-name>restWS</display-name>
<welcome-file-list>
<welcome-file>index.html</welcome-file>
<welcome-file>index.htm</welcome-file>
<welcome-file>index.jsp</welcome-file>
<welcome-file>default.html</welcome-file>
<welcome-file>default.htm</welcome-file>
<welcome-file>default.jsp</welcome-file>
</welcome-file-list>
<servlet>
<servlet-name>REST</servlet-name>
<servlet-class>com.ibm.websphere.jaxrs.server.IBMRestServlet</servlet-class>
<init-param>
   <param-name>javax.ws.rs.Application</param-name>
   <param-value>com.rest.assignment.RestService</param-value>
</init-param>
<load-on-startup>1</load-on-startup>
</servlet>
<servlet-mapping>
<servlet-name>REST</servlet-name>
<url-pattern>/rest/*</url-pattern>
</servlet-mapping>
</web-app>
When i try to return a string from my get method, it gives me a proper response. i get this exception when im trying to return a JSON response.

RSPC Variant does not exist - Could not find or load print parameters

We are on BI 7.0 (support pack SAPKW70017). We recently freshed test system from production.   After the refresh, we have problems opening all the process chains.
1. When I go to RSPC to open a process chain, I get many messages like this:
Variant &0000000067180 does not exist (there are different variant numbers)
Message no. DB612
Diagnosis
You selected variant &0000000067180 for program RSPROCESS.
This variant does not exist.
2. When I go to SM21 to check the system log, it displays many entries like below:
EJ F Could not find or load print parameters for step 1, job BI_PROCESS_TRIGGER/09134500
Documentation for system log message EJ F :
An error occurred during loading of the print parameters for a
background job step.
The print parameter record may have been deleted even though there was
a still a step that needed that data. This is an error as the
reorganization of the print parameters should prevent this from
happening.
To fix the problem, edit the step and save it, copy the job, or
schedule a new job. The print parameters will be regenerated in all
these cases.
3. I applied the OSS note 1169659 - Correction: Process variants not entered by BDLS.   The Basis rerun BDLS. But it did not fix the problem.
Would appreciate if someone could provide any help.
Thank you.

Hi Rebecca.
1) Please verify if exist process types called 'unknown job'. If exist: delete process types called 'unknown job' in your process chain. To do that please remove the chain from scheduling (menu bar > process chain > remove from schedule), afterwards switch the detail view on (menu bar > view) > right mouse click on the process type "unknown job" > displaying scheduled jobs > delete that job. After deletion of the 'unknown jobs' activate and schedule your process chain again.
2) After the removal of the 'unknown jobs' please check if the error messages with the missing variants pop up when calling your process chain disappears. If not, please implement and execute the attached report Z_FIND_JOBS_WITHOUT_VARIANT which deletes the jobs without variants.
I have already attached report as Report Z_FIND_JOBS_WITHOUT_VARIANT, you can download and create the report accordingly.
= = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = =
REPORT Z_FIND_JOBS_WITHOUT_VARIANT.
data: l_t_job type table of tbtcp with header line,
      l_s_varsel    TYPE rsvar,
      l_t_variant   TYPE TABLE OF rsparams.
parameters: delete type rs_bool.
select * from tbtcp as job into table l_t_job
                    where progname = 'RSPROCESS'
                    and   exists ( select * from tbtco
                          where jobname = job~jobname
                          and   jobcount = job~jobcount
                          and   status = 'S' ).
loop at l_t_job.
l_s_varsel-report = l_t_job-progname.
l_s_varsel-variant = l_t_job-variant.
CALL FUNCTION 'RS_VARIANT_CONTENTS'
    EXPORTING
      report               = l_s_varsel-report
      variant              = l_s_varsel-variant
      execute_direct       = 'X'
    TABLES
      valutab              = l_t_variant
    EXCEPTIONS
      variant_non_existent = 1
      variant_obsolete     = 2
      OTHERS               = 3.
if sy-subrc <> 0.
    write: / l_t_job-jobname, l_t_job-jobcount.
    if delete = 'X'.
      CALL FUNCTION 'BP_JOB_DELETE'
        EXPORTING
          JOBCOUNT = l_t_job-jobcount
          JOBNAME = l_t_job-jobname
        EXCEPTIONS
          OTHERS   = 1.
      IF SY-SUBRC <> 0.
        write 'not deleted'.
      else.
        write 'successfully deleted'.
      ENDIF.
    endif.
endif.
endloop.
= = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = =
I hope I can be helpful.
Thanks,
Walter Oliveira.

Could not find selected item matching value "null" in CoreSelectOneRadio

Hello,
I get the following error with my selectOneChoice components:
WARNING Could not find selected item matching value "null" in CoreSelectOneRadio[UIXEditableFacesBeanImpl, id=dyna_2709976_11]
It seem that the component looks for a selectItem object qith its value set to null, so I tried to add one with a null value to no avail. The error don't cause any problem on the rendered page but it might spam the log when many users will be connected. Anyone every got this error and found a fix to stop it from appearing?
Regards,
Simon Lessard

you said you're using selectOneChoice but the error says radio. Is the information correct?

Could not find selected item matching value "New" warning message in ADF

Hi,
I have a selectOneChoice1 for a field which has the following fixed values in it. And while creating it, I selected the 'SelctionRequired' option so that this field will always have a value.
New
Pending
Completed.
While navigating to this page, I am trying to set the value to 'New' (Retrieved from the DB) in the backing bean. But when the page is rendered, the above field is empty with the above options in the list and jdev has the follwing error message in its log.
WARNING: Could not find selected item matching value "New" in CoreSelectOneChoice[UIXEditableFacesBeanImpl, id=selectOneChoice1]
Can any one help me with this issue?
Thanks,
Priya

The value of a list binding is the zero-based integer position in the list that is selected, not the actual underlying value.
The simplest way to set the value of an attribute is to use an attribute binding (which can be bound to the same attribute as the list binding). When you set the value of an attribute binding, it sets the value as you supply it. Otherwise, you'd need to set the list binding's value to the numerical "slot" number of the one you want to change the value to.

11.1.1.4:Could not find the item selected to match the value of type Number

Hi,
I have a taskflow with an input parameter.
The input parameter value is to be assigned to a list item as the default selected value.
I have mapped the pageFlow scope parameter to set value to the list item using input page parameters defined in task flow.
but When i Run the task flow the value does not get assigned to the drop down list and jdevloper console screen shows up the following message
"Could not find the item selected to match the value 2 by type: oracle.jbo.domain.Number in LOV."
But If I click the Lov to check the values it shows that value is present in the list.
The same configurations works if the list of values is for a column with type as java.lang.String.
Is it somethng different that is to be done for a Number field to assign value from a taskflow parameter?
Edited by: user3067156 on Jun 25, 2011 3:34 PM

Hi Jobinesh,
I am assigning the default value in the task flow using input page parameters ...
<view id="VIEW1">
<page>/title.jsff</page>
<input-page-parameter>
<from-value>#{pageFlowScope.pInputTyp_Id}</from-value>
<to-value>#{bindings.pTyp_Id1.attributeValue}</to-value>
</input-page-parameter>
</view id>
It does not assign the value, if Bind variable(pTyp_Id1) NDtype and task flow input parameter(pInputTyp) class type, both are set to use type oracle.jbo.domain.Number.
If I change both to use java.lang.String and additionally also change the VO defination the accept the bind variable of type string, it assigns the value correctly.
Usecase:
I have a a task flow for which has its first page a search page.
The Search page is created using operation execute with params and dragging the query parameters on the page.
The Query parameters are to be filled using a select one choice option and the list is bound to the master values.
This task flow can be used inside a standalone page as a region to provide a search page
The same task flow can be called from within another taskflow which will provide the default values for the drop down lists ..
Since the search page is a jsff fragment i dont have a page on load handler to provide default values..
So assiging the values using input page parameters defined in task flow view tag.
For testing I am passing the taskflow input parameters by calling the task flow from a jspx page a region . When I configure this task flow a region in a page its asks for providing the values for the parameters
And the same gets configured in my testpage def as
<executables>
<variableIterator id="variables"/>
<taskFlow id="Flow1" taskFlowId="/WEB-INF/Flow1.xml#Flow1"
activation="deferred"
xmlns="http://xmlns.oracle.com/adf/controller/binding">
<parameters>
<parameter id="pTyp_Id" value="1207"/>
</parameters>
</taskFlow>
</executables>
Edited by: user3067156 on Jun 27, 2011 1:50 PM

11.1.2.1 - Overwrite Existing Values - Not Working

Hi,
Client has ASO Essbase application. They have duplicate rows of data apparently. I have the 'Overwrite existing values' box checked on the 'Data Load Settings'. I also select the 'Overwrite Existing Values' selection in the 'Data Load' window. Not sure why this is even there as it seems new or is a ASO specific functionality or something. Anyways, I created a simple file with two duplicate rows. When I load it using the rule, it doubles everything up. Then I load just a single row file with same rule and it successfully overwrites the values and loads properly.
Is there a know issue with duplicate rows within the same file that causes it to double the values during the load? Or am I fundamentally missing something on how to correctly 'Overwrite Existing Values'?

Found below out there in the documentation but trying to decipher it. If I understand the 'Buffer' will combine like rows withing a datasource automatically? But I can't figure out if that's in different source files only or within the same file?'
Rules File Differences for Aggregate Storage Data Loads
Rules file specifications for loading values to aggregate storage databases reflect the aggregate
storage data load process.
For block storage data loads, through the rules file, you choose for each data source whether to
overwrite existing values, add values in the data source to existing values, or subtract them from
existing values.
For aggregate storage data loads using the aggregate storage data load buffer, you make this
choice for all data load sources that are gathered into the data load buffer before they are loaded to the database.
To use a rules file that was defined for a block storage outline with an aggregate storage outline, first associate the rules file with the aggregate storage outline. See “Associating an Outline with an Editor” in the Oracle Essbase Administration Services Online Help.
For aggregate storage databases only:
•     If you are loading data and values exist in the database, select an option from the Data load values drop-down list for overwriting existing values, adding to existing values, subtracting from existing values, or replacing the contents of the database.
•     Select whether to ignore missing values and zero values in the data source.
•     Select whether to load the data as a new slice in the database.

WARNING: ADFv: Could not find selected item matching value ...

Using Windows JDev 11.1; I have an entity object with an attribute which has a LOV configured to supply a select-one-choice render. The LOV query requires that a bind variable be supplied. When creating a new record in the entity via the VO, I can use the ViewImpl to create a new row, retrieve the RowSet which corresponds to the attribute LOV query, set the named where clause parameter, and I'm away. When updating however, I'm getting the following error reported:
09/12/2009 2:44:04 PM oracle.adfinternal.view.faces.model.binding.FacesCtrlListBinding getInputValue
WARNING: ADFv: Could not find selected item matching value EMPLOYER of type: java.lang.String in the list-of-values.
I can't supply the bind variable value before the row is instantiated (and presumably populated with the current value/key) because the View Accessor RowSet is only accessible via the RowImpl. If after the query has executed, I apply the bind variable value, re-execute the RowSet query, I can see that it's populated, and I can create a RowSetIterator to loop through the LOV RowSet and confirm that the key/value is there. I can even setCurrentRow on the RowSet but I still find that the above error appears in the serve log output seemingly after all this code executes.
So my question is what is the technique for supplying bind variables to attribute LOV View Accessors as part of an underlying EO object query.
In the run-time, the list items appear unpopulated (current value and list items). If I reload the page, it all comes up fine, which could tend to suggest that a PPR event might fix me up, but I would prefer to know how this should be done.
Thanks in advance.
Edited by: robli on Dec 9, 2009 9:01 PM

Hi,
Is your issue resolved. I'm facing similar issue. I have created a viewaAccessors in EO, associated these to ViewObject attributes as List of Values.
I created the table in UI using the ViewObject.
I see those as selectOneChoice but not values (Empty list).
If I create new record in the table by CreateInsert. table now shows the ListOfvalues.
any Idea what am I missing.
Thanks,
Satya
Edited by: stammine on Mar 2, 2010 4:09 PM

Hello buy a movie on apple tv, and now can not find the device tells me I should go to settings / downloads / check downloads, but that does not exist in the menu of the apple tv, please help

Hello buy a movie on apple tv, and now can not find the device tells me I should go to settings / downloads / check downloads, but that does not exist in the menu of the apple tv, please help

Welcome to the Apple community.
A number of people have reported similar issues recently, many appear to have found a discrepancy of some kind in their account settings and making changes to these settings or simply resetting them has resolved the matter.
Check your account details are correct, check that you are using the correct details for Location, Region and Time Zone. You may want to change these settings and then change them back to see if that helps.
You might also try logging out of and then back into your iTunes account (Settings > iTunes Store > Apple ID’s > Sign Out) and restarting your router. (Some have reported that after doing this, they need to check for rentals even though it may report that there aren’t any, after which rentals once again appear in the ‘movies’ feature)
Rentals should appear under their own heading in the ‘Movies’ feature, you might also check at Settings > iTunes Store > Check For Rentals.

Warning: Could not find the customization level value for document

Hi All,
I am trying to upload the translation for one of the page at responsibility level.
I am getting following warning when running the below command.
java oracle.jrad.tools.trans.imp.XLIFFImporter $APPL_TOP/xmci/12.0.0/fr-CA/Translated/ARIACCTDETAILSPAGE.xlf -username apps -password apps -dbconnection "$AD_APPS_JDBC_URL"
Warning: Could not find the customization level value for document "/oracle/apps/ar/irec/accountDetails/webui/customizations/responsibility/51688/ARIACCTDETAILSPAGE".
The same is working fine if the translation is for some attribute at site or function level.
Did anyone faced this kind of issue.
Thanks,
Anoop

Anoop,
I am sure you would have verified the responsibility id in the target instance is 51688(may be source instance your resp id is 51688 and in target it is different).
Have a look at this below notes, it might help.
1077267.1 - Unable To Move Resp Level OA Personalization From 1 Env To Another
848851.1 - Attempting To Upload XML File Generates Error: Could not find the customization level value for document
Thanks.
With Regards,
Kali.
OSSI.

Have been using successfully Acrobat 8 Standard, version 8.3.1 for years. Suddenly can not digitally sign anything because software can not find "existing digital ID file?

Have been using successfully Acrobat 8 Standard, version 8.3.1 for years. Suddenly can not digitally sign anything because software can not find "existing digital ID file?

Are you still using Acrobat 8? If not read further.
All Acrobat versions prior to 11.0.07 had a security flaw that they allows signing with certificates that had "Extended Key Usage" (EKU) restricted to certain certificate uses and those did not include document signing. Most frequently those were certificates with "Client Auth" or "Server Auth" in EKU. Acrobat/Reader 11.0.07 fixed this problem, which also means that while previous versions accepted such certificates for signing 11.0.07 and later do not.

Re: Camera. I can zoom in or out when taking pictures. When taking videos I can not find this option. Does it exist? Thanks.

Re: Camera. I can zoom in or out when taking pictures. When taking videos I can not find this option. Does it exist? Thanks.

On iOS 5? Yes it does, you just have to pinch like u would to make page bigger in safari for example.

Just downloaded Yosemite on my Mac and the Yosemite update for Garage Band. Now when I open an existing Garage Band project and click on a vocal track, a message window says, "Could not find General Audio 10" and have no smart controls. Help?

Just downloaded Yosemite on my Mac and the Yosemite update for Garage Band. Now when I open an existing Garage Band project and click on a vocal track, a message window says, "Could not find General Audio 10" and have no smart controls for that track (reverb, etc.) Help?

Try this fix posted by Robinson Collins:
Re: I downloaded Garage Band 2x and the same note appears: there is no General Audio 10. Please advise. Thank you.
Try this: Go to your menu bar, select "Garageband" and then "Restore Sound Library..."
It can take awhile to download as it's a pretty big library. You might need to also select "Update Sound Library..." after the restore is done.

RV220W not finding "known to be existing" value -- SNMPv3 protocol

Similar Messages

Maybe you are looking for