Satellite C655D-S530​3 will not boot from cd/dvd drive

I have already set the boot order in the BIOS to boot from cd/dvd drive first and it still goes straight to the HDD and starts Windows 7. I searched for this problem and found some people saying to switch it to CSM boot or disable secure boot but none of these options are available in the BIOS. I have it set to normal boot instead of fast so thats not the problem. Can anyone help me here? I am trying to reformat and reinstall Windows 7. I know the Windows 7 installation disk I have is good because I have used it in another computer and the cd/dvd drive works fine. I just can't get it to boot from the cd/dvd drive before the HDD.
Solved!
Go to Solution.

Satellite C655D-S5303
Downloads here.
Try setting the HDD to lowest boot priority. See Dave's solution in this message.
It's certainly easier to restore the hard disk to its original out-of-the-box contents using Toshiba recovery media. All the drivers and utilities are preinstalled in the proper order. Windows is preactivated.
If you failed to burn recovery discs, you can obtain recovery media from Toshiba. Scroll down to Get Recovery Media here
For instructions, see the section Restoring from recovery DVDs/media, which begins on p. 76 of the User's Guide.
   Satellite/Satellite Pro C600 Series User’s Guide
If you want Windows 7 Professional, upgrading takes only minutes.
   Upgrade to another edition of Windows 7 by using Windows Anytime Upgrade
-Jerry

Similar Messages

  • Satellite C655D-S5303 will not boot from cd/dvd drive

    I have already set the boot order in the BIOS to boot from cd/dvd drive first and it still goes straight to the HDD and starts Windows 7. I searched for this problem and found some people saying to switch it to CSM boot or disable secure boot but none of these options are available in the BIOS. I have it set to normal boot instead of fast so thats not the problem. Can anyone help me here? I am trying to reformat and reinstall Windows 7. I know the Windows 7 installation disk I have is good because I have used it in another computer and the cd/dvd drive works fine. I just can't get it to boot from the cd/dvd drive before the HDD.

     
    Satellite C655D-S5303
    Downloads here.
    Try setting the HDD to lowest boot priority. See Dave's solution in this message.
    It's certainly easier to restore the hard disk to its original out-of-the-box contents using Toshiba recovery media. All the drivers and utilities are preinstalled in the proper order. Windows is preactivated.
    If you failed to burn recovery discs, you can obtain recovery media from Toshiba. Scroll down to Get Recovery Media here
    For instructions, see the section Restoring from recovery DVDs/media, which begins on p. 76 of the User's Guide.
       Satellite/Satellite Pro C600 Series User’s Guide
    If you want Windows 7 Professional, upgrading takes only minutes.
       Upgrade to another edition of Windows 7 by using Windows Anytime Upgrade

  • Will not boot from CD/DVD drive even with "C" key pressed

    I have a G4 with a hard drive that is (apparently) dead. I would like to boot off the CD drive, but that does not work. I press "C", then turn the power on, continue holding down the "C" key, and the hard drive just makes some clicking noises for about 20-30 seconds, then gives up. The computer will not boot at all. Same thing happens when holding down "Option" instead of "C"
    Why would the computer not boot off the CD drive?
    Any tips would be greatly appreciated. Thanks!
    Mike
    Mac G4 400 MHz   Mac OS X (10.3.9)  

    Hi, Michael!
    If this topic is now "history", please close it out as "answered". If you still have a problem with the AGP G4, still close this topic out and post over in the G4 section and we'll happily help you out over there.
    Regards,
    Gary

  • Restore Disc Will Not Boot From External DVD Drive

    I am using an original MacBook Pro that I decided could use a good restore, and started to clean house. The optical drive is broken, so I am using an external USB drive. I inserted the restore disc that came with the computer (It has OS X 10.4.6 on it), erased my HD, and proceeded to install Tiger. However, setup froze while installing Photobooth, and I was forced to shut down the computer.
    I'm trying to get my Macbook Pro to boot from the restore disc that came with it so I can try setup again, but it won't work. If I hold C during the boot, I get a flashing folder with a question mark over it. If I hold option, I get a cursor, but just a blank, gray screen. In both instances, the external DVD drive is active and reading the disc, but I'm not getting any results on the screen. I've also reset PRAM.
    If I can just get my computer to boot from the disc, I should be able to get back on track. Thanks.

    When I press option during boot, nothing happens. Just a gray screen and cursor, like I described above. I haven't been able to test the external drive yet on another mac to see if it is bootable because I can't find the other computer's boot disc at the moment, but I'll try later with something else.
    I have been able to access the drive through Target Disk mode successfully though. Is there something in particular I should do with the files? The folders are:
    Applications
    cores
    dev
    etc
    Library
    OSInstall.mpkg.998YblbM
    System
    tmp
    Users
    var
    Volumes

  • Wiped macbook pro will not boot from install DVD

    I recently purchased an older MacBook Pro that came with the OS system wiped but it did have the original Install DVDs.  The computer will not boot from the DVD.  I have booted holding down the C key and nothing happens.  I have booted holding down the Option key and it shows the Install DVD and I select this and nothing happens.
    How do I get it to open up the Utilities from the DVD to install the operating system?

    It could be a problem with the optical drive, but also may be due to the DVD's being for a different model.
    Exactly which MBP do you have, and what serial numbers are on the discs ?.

  • Mac Mini i7 (Mavericks) will not boot from the external drive

    Mac Mini i7 (Mavericks) will not boot from the external drive with Disk Warroir 4.4. or Drive Genius or Lion.
    Not even from the external Firewire hard drive with Mavericks

    Does the external HD have a GUID partition table?
    Is the external drive formatted Mac OS X Extended (journaled)?
    Is this a 2011 or late 2012 Mac?
    How was Mavericks installed on the external drive?
    Who is the builder of the drive mechanism in the external drive?
    Who is the builder of the external enclosure?
    What type of interface does the external drive have USB2, USB3, Firewire 400, Firewire 800, thunderbolt?
    Is the external enclosure directly connected to the mini?
    Have youtried a different interface cable?

  • Satellite P300-1A8 will not boot from disc drive

    Hi,
    I had a little play with start up programs, partitioning the hard drive and marking as active and deleting programs i thought i did not need.
    I obviously had no idea what i was doing!
    Laptop will go to toshiba screen then goes blank, i can not boot from the disc drive.
    I put the hard drive into another laptop and it works fine.
    I put the hard drive of that laptop in the buggered one and that works fine.
    How the hell do i put the original one back with it working??
    Really really stuck with this!!!!!
    Any help would be appreciated.
    Only thing i havent tried is the recovery disc but im not paying for one if it wont boot as itl be a waste of money.
    Seems like its a compatability problem with cpu and hard drive as they dont want to be friends anymore!!
    Thank you in advance

    Hi!
    Can you boot in the safe mode?
    If you dont have a recovery disk, use the Microsoft installation disk and try to boot from it.
    And you said that you cant boot from disc drive, did you tried different disks?
    Maybe some are not readable or not bootable.
    The best way would be a recovery disk. The installation takes a few minutes and you have a clean installation with all drivers and tools from Toshiba.
    Bye

  • Help needed on startup. My computer will not boot from the CD drive!!!

    Problem with iMac G3 333, the Message on the screen states: "The System Software on the starup disk only functions on the media, not if copied to another drive." Like a fool, I copied the system folder from the original system software 9.2.2 on to the iMac. System disk which is not a complete system folder when used on the computer. I have searched the Internet, but can not find an answer. I have tried everything, holding down the C key, "Delete, Opition, Apple key, shift" holding the mouse down on startup, various combinations of other keys, etc. The CD starts to spin, but the computer switches to the hard drive and the message above returns. No matter what I try I still can't boot from the tray loading CD drive. Is there any Firmware code that I can use. I know how to access Firmware on the Imac and can boot the iMac using Firmware, but I don't know how to use Firmware to boot the CD drive which I need to do so I can reload the original software. CAN SOMEONE PLEASE HELP? Thanks, Jim

    Yes, I have tried both System Softwares a number of times. The C key will not boot up the CD drive and the harddrive always boots with the original message. I need to get the CD drive to boot so I can reloaded tge original software. Do you know anything about booting the CD drive using Firmware? Jim

  • Intel Xserve will NOT boot from hard disk drive

    I have two Intel Xserves 2.0 QC machines
    I have tried to re-install version 10.4.11 OS (don't ask) onto a Hard disk drive that is in a Disk drive caddy and inserted in the machine.
    When booting from The installation DVD media
    The disk is seen by the "Disk Utility" (the disk is partitioned as GUID boot) and the installation proceeds to the disk.
    Once the first pass of the installation is complete and the system reboots, the system shows the folder and ? mark.
    If I boot and hold "ALT" key to view all avaialble boot options the Hard Disk Drive does NOT appear as valid boot disk.
    It does show, the still inserted Installation DVD.
    I CAN boot from an external firewire drive and the Hard disk drive is visible to the OS once logged in.
    I have tried different caddy postions (left, middle and right)
    I have tried bona fide Apple supplied Disk drives
    I have tried various different caddies
    I have tried installing Operating System 10.5.*  and  10.6.8 server
    I have run SMC reset and system reset
    But still I cannot boot off from any Hard Disk Drive inserted in a caddy at the front of the system.
    Has anyone seen this behaviour?
    Is it fixable?
    Do I have replace something like the Hard Disk Drive back plane circuit board? Or even the main logic board?
    I have now run out of ideas and cannot find any help in discussions or just googling.
    ANY help would be very appreciated
    Regards
    Tony

    Antonio Hi !
    QC = Quad core  or  QX as it is written on the "pull out" serial number tab at rear of system
    I have 3 late 2006 Intel xserves
    On my intial posting I declared 2 were 2.0 machines - when I was trying to be concise
    2 of the macines are 2.66 systems and 1 is 2.0 system - all are QX machines
    the 2.0 and 1 of the 2.66 will NOT boot from the ADM and disk inside the system - whereas the other 2.66 system will.
    I have many different Caddies and these have different product/model number labels
    603-9965
    603-9545
    603-9796
    these are marked "intel SATA"
    The 80Gb was only one of the drives tested - I have used Seagate 400Gb 750Gb and 1Tb  -  all of which have been used in systems at one time or another
    and as I said the drives ARE visible once the operating system (either installation DVD or external firewire are booted from) - they are just NOT visible when the system is searching for boot media.
    Thanks for the guide - I will look through that and continue to try and find an answer

  • IBook G3 will not boot from CD/DVD

    Ok, I have an iBook G3.
    I was restoring it to factory with the Software Restore disks which came with the unit as I was planning to move on to a new unit.. But there was a power cut in the middle of the process and the unit shut off. Now, it does not recognise a HD when booting holding option.
    It also will not boot from any CD/DVD other than the Apple HW Test disk provided with the unit.. All other disks spin up and then get ejected, on the odd occasion it does not eject, it boots to a icon of a floppy diskette with a flashing ? (Saying that, I did manage to get it to load from the restore disk 1 once, but it just said it could not mount the image file)
    The HW test disk returns no problems
    I have reset PRAM multiple times, and reset nvram and all in Open Firmware. I have also reset PMU as a last resort, but no luck
    Any ideas?

    Hi, and welcome to Apple Discussions.
    Do you have DiskWarrior, maybe?

  • Satellite A15-S129 will not boot from CD - missing NTLDR message

    I decided to do a fresh install on my neighbors A15-S129 Satellite. After trying all sorts of ways, I decided to remove the hard drive and reformat it in my computer. When I put it back in the satellite, I expected it to boot from the cd since the hard drive was blank, but no, I get the "missing ntldr message".
    The Bios does not let the cursor move over to the side where I could change the boot order. When I start the computer, I cannot press f2 or f12 to change the boot order.
    After no luck I just started doing all sorts of things to troubleshoot. One: I notice if I remove the hard drive and leave the slot blank, I get IDE error, then SURPRIZE!
    The boot goes to the cd, BUT just when I thought I could just install, I get the screen that says missing hard drive, even if I hurry and push the hard drive in.
    Why does the computer insist on doing one thing: starting windows xp, even if the drive is bank.
    Why can't I, or rather, how can it make it skip the harddrive and move on to the cd drive?
    I've never been stumpted like this before! Please help, my neighbor will have my head!

    I solved the problem, and I decided to reply to add to this forums knowledge base.
    The hard drive was "Locked" so even though I reformatted there remained data on there protected, and so the computer went though its boot sequence, and stopped at the hard drive, hence the NTLDR message. There was data still on there looking for Windows XP.
    SO in order to do a fresh install, in my case install windows 98 and then upgrade to XP, I had to put the hard drive in another computer that had a floppy drive, boot from Windows 98 boot disk, when I got to a DOS prompt, change to C: , then type in LOCK /? , this unlocked the drive.
    Then I used a little utility called WIPEOUT to clear the drive, then I typed REFORMAT C: , then started to install Win98, but stopped right after the install program copied files to the drive. Then I removed the hard drive and put it back in the Satellite (I would not have to have done it this way if the A-15 had a floppy!) and install continued, and all is fine.
    No repair center charges!

  • Satellite L40 - recovery disc will not BOOD from CD/DVD drive

    Hi guys!!
    I am trying to use the recovery disc on my friends laptop...but it will not boot up at all from the CD/DVD drive ... I have been trying for two days..... Have checked the BIOS settings
    1. CD/DVD drive
    2.hdd
    3.network.
    have pressed the F12 key at start up as the recovery disc instructions suggests....this brings the boot up screen asking where to boot from...I select CD/DVD drive.... the drive makes a few noises and then after around a minute and a half...the Vista log on screen appears as usual. I have also tried starting up and pressing C but the same thing happens, just keeps loading Vista log on screen.
    I have seen this is a common problem whilst researching the net but I have not seen a viable suggestion to fix.
    Whilst going thru some user setting in Vista Im positive I seen a boot option that could be changed there and Im sure that hdd was selected.... did I dream this??
    Im exhausted guys ...any suggestions pleaaaase x

    Turns out the disc wasnt in 100% ..looked fine ..but when i pushed round all of the disc ..it made a tiny snap noise..and that was what the problem was...have also discovered...its an equium machine not a satellite.. system is in great shape now :-)

  • MBP 13" (2010 model) will not boot from Restore DVD!

    I just upgraded the HDD on my 13" MBP to the 1TB Toshiba MK1059GSM. The MBP is 3 weeks old. Upgrade went fine in terms of the process. However, when I insert the OS restore DVD that came with the machine and restart (using ALT/OPTION) and select to boot from the DVD, the Apple logo appears with the spinner and the system just stays like this. I can hear the DVD spinning but nothing elese ever happens! Any ideas as to what could be wrong? Could it be that this new Toshiba HDD is not compatible and the DVD does not have a driver for it?

    +*Could it be that this new Toshiba HDD is not compatible and the DVD does not have a driver for it?*+
    SATA drives use a standard interface and no additional drivers are necessary. That's not to say that the drive itself can't be faulty. As has been suggested, try removing the drive and see if you can boot from the DVD. If that works, you can be pretty sure there may be a problem with your new hard drive. Hopefully you kept your original drive so you can always put that back in. Faulty hardware can always be frustrating because you never think that's the problem. Let us know how you make out.

  • New hard drive.  Will not boot from install dvd.

    Earlier this week, I dropped my computer.
    It was probably a 3 foot fall.
    Computer froze, so I restarted and got the flashing folder with question mark.
    Started in internet recovery, and disk utility confirmed that I had killed my hard drive.
    Got a new hard drive and installed. Started in internet recovery, formatted hard drive. Disk utility says it's good to go.
    Was given the option to install Mavericks, but keep getting an error message.
    Attempted to restart from install dvd that came with the MBP. Tried every startup shortcut there is.
    Optical drive recognizes the disk, but I always get stuck on the gray screen with the wheel.
    Reset PRAM. Reset SMC. Same problems. I do not have access to another mac or a PC with admin rights.
    I'd rather not brave the Apple Store this weekend in the snow in a town that never gets snow (people drive poorly on a good day!).
    Any tips?
    Got the MBP in 2010, new. Was running mountain lion when I dropped it.
    Thanks!

    Yiou can't use Internet recovery on a 2010 Mac notebook to install any version of OS X on it. That is why you are getting that error. You have to use the original System reinstall discs that came with it to install OS X on a new drive or use the OS X reinstall disk to restore from a time machine backup.
    Since your system doesn't seem to want to completely boot from that disc you should try an external DVD drive that connects by USB port as the built in superdrives are known to fail or partially fail at any time. Don't buy an Apple external Superdrive as they only work on Mac computer that did not originally come with a built in DVD drive. Any Brand external DVD drive will work on your Mac except Apples own external DVD drive.

  • Power Mac G4 400 MHz (AGP graphics) will not boot from hard drive

    I have a Mac G4 400 MHz (AGP graphics) Machine Model: PowerMac 3.1 CPU Type:PowerPC G4 (2.8)
    When I try to boot from the hard drive I get the folder with the flashing question Mark. The Machine will start up from the OSX 10.4 installer disk.
    The system was running OSX 10.4.9 fine. I began to have problems with the hard drive, so I replaced it with an old Maxtor 5T040H4 40Gig Apple branded drive that I had sitting around.
    The drive is jumpered (r50) for Master/Single.
    I erased the drive in the old G4 using disk utility and wrote all zeros. I then used my store bought Tiger 10.4 install disk to install 10.4 on the drive.
    After restarting I still get the flashing question mark. If I leave the Install disk in the DVD drive the system will attempt to install again.
    I have zapped the PRAM, pressed the CUDA button, removed the battery and let the system sit unplugged for over and hour and it still will not boot from the hard drive.
    To test the drive I removed it and put it in a Granite Digital firewire enclosure and connected it to another mac. The drive shows up and the system appears to be installed correctly.
    What am I forgetting to do? Does anyone have any suggestions.
    Thanks in advance.
    Wesley G.

    Hi! If Tom's solution doesn't work I would reboot from the install disc and then partition the drive as 1 partition instead of erasing it. Sounds like the driver on the disk is too old and installing a new partition map should write a new driver to the drive that is compatible with Tiger. Other than that it is possible that the drive has a spin delay jumper enabled and the drive isn't spinning up fast enough and the computer isn't looking long enough for the drive. Tom

Maybe you are looking for