Satellite C850-19D wont start after UEFI to CSM change

After wrongly change BIOS between UEFI to CMS, saving changes and leave, after reeboot the screen runs mad and dont let me access either BIOS or Windows.
Sugestions?
Thanks by the way

I’m afraid there must be some BIOS or EPROM / motherboard issue.
It looks like the POST (power on self test) cannot be passed properly.
Not quite sure if the issue can be solved easily and from my point of few you would need to contact the authorized service provider for help…
Therefore I recommend you to contact the ASP guys and to ask for assistance…

Similar Messages

  • My System wont start after setting FSB to 200

    My System wont start after I'd set my FSB to 200,
    when the system starts, nothing comes up, and my Pc screen LED just blinks,
    I have tryed to reseting the Bios but it doesn't help, have also tryed with new RAM and new Graphiccard but it doesnt help.
    Please help me:-(
    Am I resetting the Bios wrong? I set the jumper to safe mode and 100mhz, then I use the jumper to clear the CMOS. And the restart at set the jumpers back
    3ghz AMD BARTON
    NVIDIA nforce2 k7bn2 Delta
    512 DDR RAM PCI3200
    300WATT

    Quote
    Originally posted by roobster
    set the multiplier lower , FSB(200) X multiplier (ex.10.5) = 2100 MHz , and your voltage raise it a bit too let say 1,700 ( default is 1.650 ) If this doesn't work at once , keep booting . My rig started up after 5 times . Strange but true .
    does not work if he has a 3000.
    they are multiplier locked.

  • Intel imac wont start after changing permission

    intel imac wont start after i changed my hard drive permission to let me read and write, then i clicked apply to all enclosed files.i turned it off no problem. then it never started up again in os x. the grey screen with apple logo appears,then after a minute it restarts, and will keep doing that if i let it. i can start up in windows xp, but i dont know how to do anything in windows xp that will affect os x. i can use the hard drive in target mode, but i cant figure out how that can help me. i use a macbook to view target disk. ive spent hours looking through help and support. finally i do not have the os install disks. PLEASE HELP!

    My apologies for the inept instructions.
    Restart normally. Open Terminal in the Utilities folder. Paste the commands in the Terminal application to avoid typos:
    sudo su
    Press RETURN. Enter your admin password when prompted.  It will not be echoed to the screen. Press RETURN again. Now paste each of the following at the prompt and press RETURN after each.
    chown root:admin /Applications
    chmod 0775 /Applications
    chown root:admin /Library
    chmod 1775 /Library
    chown root:admin /System
    chmod 0775 /System
    chown root:admin /Users
    chmod 0775 /Users
    chmod -R -N /Applications
    chown -R :admin /Applications/*
    Again, my apologies.

  • Portege Z930-118 wont start after BIOS update

    my PORTG Z930-118 failover and wont start after i upgrading in middle of upgrade i remove power and press shutdown bottom after that i see the power and wireless but screen still black ?
    Any help please

    Hmmmm.... BIOS upgrade interruption has screwed up BIOS and thats the reason why your notebook doesn't start properly. BIOS is damaged now.
    In such case you need professional help by authorized Toshiba service provider.
    On this forum you can find many threads about similar problems. Some people have tried to fix this alone and if you are interested to read how one other forum user has fixed it check please this thread.
    Ayway, you can contact nearest Toshiba service, explain the situation and ask for help.

  • 770-G45 wont start after ShutDown

    Recently installed MSI 770-G45, problem starts when i regulary shutdown comp. from WinXP or Win7 64-bit.Computer wont start after that, like ther is no power, fans dont spin, no bips, NOTHING. I got to unplug power cord and plugg it again into psu, after that it starts normaly.
    Strange thing is that computer starts normally when i manualy shutdown system(holding the power button on the case).There is no exception, starts perfectly evry time after manual shutdown, no need to unplugg powercord.
    Rest of my components> Phenom II X2 555BE, Kingston 2GB 1333mhz, Sapphire 5770, HDD WD 250gb,PSU Corsair TX 650w.
    Tried to change power cord, tried other PSU, other case (tought its maybe power button but no), changed mobo battery, installed several OS versions (XP, Win7) and still dont have solution.
    MS 7599 ver. 2.0
    Bios version 10.2
    MoBo is new bought it 3 days ago.
    PLEASE HELP!!!!!

    First: It is important to clear CMOS after a BIOS update. Unplug power cable before the clearing, as there can be no power in the system
    Second: Rebuild the system, but outside the case. Use only PSU, motherboard, processor, one stick of memory and graphics card. If it works better then, you may have a short, from a stand-off too many, or poorly isolated wire somewhere.
    But I second it sounds like a motherboard problem. You'd better contact the one who sold it to you.
    Oh, an oldie thing! You will need to install Windows again, with the new motherboard and all.

  • SSMS wont start after Installing SQLServer

    Hello,
     After SSMS wont start after updating VS2012. I have unistallled and installed a number of times but the error message I keep getting indicates that Visual Studio shell Isolated is missing. I have tried to install this directly from the set up dvd but
    no success.
    Also I noticed that VSShell is missing in the C:\Program Files (x86)\Microsoft SQL Server\120\Tools\Binn.
    I am assuming that this has something to do with it.
    Can someone please tell me how to fix this?
    Thank you.
    here is the error message received

    Hi,
    Try the below solution and see how it works.
    Note: Take a backup of the key before make any changes on the registry keys.
    http://support.microsoft.com/kb/322756
    Start regedit.exe
    Go to HKEY_CURRENT_USER\Software\Microsoft\SQL Server Management Studio
    Delete 12.0_Config
    Restart ssms.exe
    Here is the original thread:
    http://social.msdn.microsoft.com/Forums/sqlserver/en-US/aeff13b3-3960-4724-bb9a-7e585651d7f4/sql-server-2012-error
    Thanks.
    Tracy Cai
    TechNet Community Support

  • Safari wont start after i installed avi player any suggestions?

    safari wont start after i installed a avi player any suggestions?

    You may have installed the "VSearch" trojan. Remove it as follows.
    Malware is always changing to get around the defenses against it. These instructions are valid as of now, as far as I know. They won't necessarily be valid in the future. Anyone finding this comment a few days or more after it was posted should look for more recent discussions or start a new one.
    Back up all data before proceeding.
    Step 1
    From the Safari menu bar, select
              Safari ▹ Preferences... ▹ Extensions
    Uninstall any extensions you don't know you need, including any that have the word "Spigot," "Trovi," or "Conduit" in the description. If in doubt, uninstall all extensions. Do the equivalent for the Firefox and Chrome browsers, if you use either of those.
    Reset the home page and default search engine in all the browsers, if it was changed.
    Step 2
    Triple-click anywhere in the line below on this page to select it:
    /Library/LaunchAgents/com.vsearch.agent.plist
    Right-click or control-click the line and select
              Services ▹ Reveal in Finder (or just Reveal)
    from the contextual menu.* A folder should open with an item named "com.vsearch.agent.plist" selected. Drag the selected item to the Trash. You may be prompted for your administrator login password.
    Repeat with each of these lines:
    /Library/LaunchDaemons/com.vsearch.daemon.plist
    /Library/LaunchDaemons/com.vsearch.helper.plist
    Restart the computer and empty the Trash. Then delete the following items in the same way:
    /Library/Application Support/VSearch
    /System/Library/Frameworks/VSearch.framework
    ~/Library/Internet Plug-Ins/ConduitNPAPIPlugin.plugin
    Some of these items may be absent, in which case you'll get a message that the file can't be found. Skip that item and go on to the next one.
    The problem may have started when you downloaded and ran an application called "MPlayerX." That's the name of a legitimate free movie player, but the name is also used fraudulently to distribute VSearch. If there is an item with that name in the Applications folder, delete it, and if you wish, replace it with the genuine article from mplayerx.org.
    This trojan is often found on illegal websites that traffic in pirated content such as movies. If you, or anyone else who uses the computer, visit such sites and follow prompts to install software, you can expect more of the same, and worse, to follow.
    You may be wondering why you didn't get a warning from Gatekeeper about installing software from an unknown developer, as you should have. The reason is that the Internet criminal behind VSearch has a codesigning certificate issued by Apple, which causes Gatekeeper to give the installer a pass. Apple could revoke the certificate, but as of this writing has not done so, even though it's aware of the problem. This failure of oversight has compromised both Gatekeeper and the Developer ID program. You can't rely on Gatekeeper alone to protect you from harmful software.
    *If you don't see the contextual menu item, copy the selected text to the Clipboard by pressing the key combination  command-C. In the Finder, select
              Go ▹ Go to Folder...
    from the menu bar and paste into the box that opens by pressing command-V. You won't see what you pasted because a line break is included. Press return.

  • Satellite P300-156: Vista wont start after installation of Toshiba Tempo

    Hi
    I have a new Satellite P300-156 which I have been using for about a month with no problems. It has been great.
    This morning I had a message come up to install Toshiba Tempo which I did and all was fine until I restarted the laptop and now Vista wont start.
    I have followed all the diagnostic tools, tried system restore etc... but still nothing.
    I currently live in Italy, so is hard to take it into a computer repair shop as I dont speak Italian and the operating system is in english.
    From what I can see my only option now is to do the TOSHIBA HDD Recovery, but I would loose some data which I have done since my last backup. Is there any way to backup data to a usb storage device using command promts before I do this, or is there a simpler way out of this?
    Any advice would be great.
    Thanks
    Keith

    Hi
    Thanks for getting back so soon, however, F8 does nothing when starting. I have an option of F2 or F12, but neither gives me options to access last known good configuration.
    Is that the same as a system restore from the Vista system recovery options as I have tried this (gives you a list of last known configurations). But still no luck.
    If I do the TOSHIBA HDD Recovery function do I need a disc for this?
    thanks

  • Windows 8 wont start after format

    Hello,
    So i decided to format my pc for the first time since i build it, i did everything as usual but it wont start, tried the way xmad posted but its the same, im using the same iso i used the first time, after the installer says its going to restart to complete the instalation, the pc reboots and then nothing happens, i can move the mouse pointer but the screen is black, this happens when i boot from the hard drive with the prefix "UEFI".
    if i boot from the hard drive without the prefix "UEFI" i can see the windows 8 logo loading but then its the same black screen.
    PC specs:
    i7 4770k
    Msi z87 mpower max
    120gb ssd
    16gb ram
    850w psu
    radeon hd7970
    Any ideas?

    No i didnt update the bios.
    Update: I got a copy of windwos 8.1 and tried installing it the same way and it worked(still havent updated the bios).
    i dont know what was the problem with win8, i dont know if the iso file got corrupted which is very rare since i used it like 2 weeks ago in another pc, it cannot be the usb stick (i used the same usb stick to install win 7 and 8.1) and also tried installing it from a dvd.
    I think im going to stay with this windows, thanks for replying.

  • Safari wont start after Leopard software update

    After updating Leopard to 10.5.7, Safari wont start. I get an error message "Cant load Tastyapps AV plugin." or something to that effect.
    What gives? anyone know?

    I was using Videobox as a trial version (on the site you have the option of buying or trying for 30 days). After the 30 days it stopped working and I just moved it to the trash. I seems to have left something in Safari however that causes it to not want to start.
    Using Firefox i was able to go back to the Videobox site and download and install the trial version again. I was then given the option of installing the Safari plug in which i did. I then went to the Videobox menu and clicked on uninstall Safari plugin. and then i just moved videobox to the trash again using AppCleaner.
    So, you should be able to do the same thing. Just click on "download" instead of "buy" on the Videobox site. I'm sorry, I couldnt find the plugin files for manual deletion either.
    Maybe you should start a new thread and someone will know how to do that.
    Thanks!

  • Touchsmart tm2 notebook wont start after standby

    I have a touchsmart tm2 that shot down after I started using it from stand by and now the notebook wont start, only the battery light is showing but it won´t do anything else

    Hi
    You have a couple of options as I see it please try these steps might help you to fix your issue.
    Resolving Problems with Sleep and Hibernate Mode
    Let us know how it goes!
    *Although I am an HP employee, I am speaking for myself and not for HP.
    ****Click the White Kudos star to say thanks****
    ****Please mark Accept As Solution if it solves your problem****
    Regards
    Manjunath
    Let us know how it goes!
    "I work for HP."
    ****Click the (purple thumbs up icon in the lower right corner of a post) to say thanks****
    ****Please mark Accept As Solution if it solves your problem****
    Regards
    Manjunath

  • Garageband wont start after update to ilife 09

    i update my ilife from 08 to 09, and now my garageband wont start anymore,it stucks everytime i start and the window "initialize" will not close.
    at this point i try everything, delete the preference files in "user -libery-preferences" ,starting with apple -install-DVD and repair permission.
    also delete garagaband 09 and re-install GB 08, after this and deleting pref-files again garagband 08 will start normaly
    then i try again to update to Gb 09...and it stucks again when the app launch.
    GB 09 will only shows the initialize window and stuck !
    Please help

    i had the same problem when i got my new macbook. I even tried to restore the whole OS then it finally works. But then it crashes again after i install some other program. I suspect the garageband 09 crash with some specific music program...but i still can't figure out which one. I've installed Garritan Personal orchestra, Emu 0404 driver, melodyn essential after that, i bet one of these program have problem.
    What about you, have you got any other music program in your mac?

  • Skype wont start after update on Android 4.0

    My skype wont start any more after update. When i click on icon appear the intro and close all times. Someone can help me?

    Try help here friend with skype support chat:
    http://www.skype.com/go/help.support.request
    OR
    https://support.microsoft.com/en-us/skype?language=en&locale=EN-US&oaspworkflow=start_1.0.0.0&needsl...

  • Gnome wont start after login

    I can get it to start manually with gnome-session but it wont autostart after i login.
    I added exec gnome-session to /etc/X11/xinit/xinitrc and to $HOME/.xinitrc.

    isez2001 wrote:I keep seeing dbus 0.93 mentioned along with Gnome 2.16, and was wondering if perhaps the dbus update was prematurely put into current when Gnome 2.16 was moved to extra?
    It's probably a mirror syncronisation issue. A lot of packages were moved from testing to current/extra.  Probably users either didn't fully updated their system (pacman -Syu) or are using a mirror which haven't sync yet.
    Also, make sure that you don't use a different mirror for current and extra. If you use an up-to-date mirror for current and a less up-to-date mirror for extra, you might get this kind of problem. You can temporarily switch to a more up-to-date mirror or to the main server to make this big update.

  • Iphone 5 wont start after standby

    My iphone 5 screen went with blck/wite vertical stripes. After one month going to flat battery and charging it restarted. Now every time goes to standby it wont start. Only by rebooting. Does anyone know how to fix it? Is it a iOS 7.0.6 sw problem? YOur help is very much appreciated as my phone is out of warranty for a month :-(

    Hello Duartesilva,
    It sounds like you are unable to turn the phone back on normally and must reset it to get back to your home screen. I recommend starting creating a backup of your device to iTunes with this article:
    iOS: How to back up and restore your content
    http://support.apple.com/kb/HT1766
    And restore it from your backup with this article:
    Use iTunes to restore your iOS device to factory settings
    http://support.apple.com/kb/ht1414
    If it is a software issue, these steps will resolve it.
    Thank you for using Apple Support Communities.
    Cheers,
    Sterling

Maybe you are looking for