Satellite L30-10Y: Checksum error after upgrading to 2Gb RAM

Hi
I have a Satellite L30-10Y ^ months ago I upraded the RAM to 1.5Gb by adding a 1Gb RAM card to the 512Mb card supplied this worked fine.
I also upraded my sons Hi-Grade lapto with exactly the same specification of RAM which also worked fine. So I decided to up grade my L30 10Y with another card of the same specification to bring it upto 2 Gb as specified by TOSHIBA.
I booted the computer to find the hay presto after the start screen The Following message appeared *"_The file is possibly corrupt.
The file header checksum does not match the computed checksum_"* The computer then froze and I turned it off.
Checks I made Tried both cards in both slots No change, 1 card in both slots (one slot empty) Works fine. Other card in both slots(works Fine) Sons Card in my computer both slots (works fine) All three cards and 512mb card in all configuration of both slots and cards(works fine). All three 1gb cards in all configerations of cards and slots back to error message and some time 1 long beep and 2 short ones.
Yes the cards were installed properly. Cannot alter anything to do with BIOS although this can be accssed. Cannot run from dvd drive although I can select it.
Went back to 1.5Gb and reinstalled all OS from Toshiba recovery disk tried all over again same results. Running windows vista home basic, Bios is the latest download. RAM is compatible. Sons cheep Hi-Grade accepts all RAM in all Configurations no bother OS windows XP.
Can anyone think of anything I have not tried or should I just go and by a hi-grade computer?

Hi Eldorado
Thanks for your reply, 2 of these modules were bought 6 months ago from the same company at the same time (company Offtek) who do a computer scan and provide the modules specific to your computer, and even then I checked the specification of the modules against the upgrade that Toshiba who also scanned my computer on registration and the modules are DDR2 533MHz (PC2-4200) 200-PIN SODIMM . The Third module came from the same company with the same specification.
I am very sure that all three modules will be compatible to the computer, and the specifications does not require the modules are matched pairs like the old sd ram. So what we have is a computer that will run two completely differnt modules of different sizes made by different manufacturers possibly slightly different specs, but will not run two modules from the same manufacturer made at the same time with exactly the same spec.(Must be a break through of innovation for Toshiba!)
I think the beeps may have been a little misleading as these did not accord every time I started the computer over the many tests I did, I still have to look up what these codes signify. I tried looking in the Toshiba knowledge database but I think it's empty or they just don't have any knowledge complete waste of time or I don't know how to use it.
My next step its to contact Offtek and see what they suggest, Find out what the Header checksum is and what it is supposed to report and find out what the computed checksum is and why it does not match. One more thing I did notice that in the BIOS it did not report the full 2048mb it only reported 1984mb of RAM but I think this may be that video memory uses part of this. *_Unless someone out there knows something different_*

Similar Messages

Satellite L675D: Blue Screen error after upgrading to Windows 8

Hello,
I've recently upgraded my Toshiba laptop to Windows 8 and every time I use it, after 5-10 minutes, I get a blue screen page of error and the laptop restarts.
The problem is really annoying.
I've discovered that if I don't plug in the battery charger, the laptop works normally, but I'd like to solve the problem properly.
What should I do?

> I've installed Windows 8 Pro with a regular activation key: I had Windows 7 before and I simply updated it to Windows 8. >I don't know about the drivers.. I think that may be the problem, but I also reckon the drivers are ok! Do you know a good way to check it out? Or where I can find the proper drivers?
Windows 8 drivers for Satellite L675D dont exist on Toshiba EU driver page. The L675D series does not support Windows 8.
However, even if the drivers are not available and Windows 8 is not supported, it should not be a big problem to run this system on the Satellite L675D.
You said that you simply updated the Win 7 to Win 8.
Maybe you should try a clean installation of Windows 8?
I think its worth a try in case its an software problem.
By the way: I assume this kind of problem did not appear using Windows 7. Right?

Time machine fails backing up with a "backup disk not found" error after upgrade to Lion 10.7.2

Time machine fails backing up with a "backup disk not found" error after upgrade to Lion 10.7.2. I've erased and reformatted the drive; reconnected Time Machine(it saw it) and began a new backup. The backup starts again but fails before completing with backup drive not found error. I used the 10.7.2 combo update. Any help on how to fix this problem would be appreciated.

Arghhhhhhhhhhhhhhhhhhh!!!!!!
After waiting since October for a fix, I have now upgraded the firmware on the Time Capsule and installed the new Airport Utility, released yesterday, and the situation is even worse.
Up until now, the Airport Utility had an option to disconnect all drives manually and the Time Capsule would then work until the next reboot – a temporary (?) work-around.
Now that option does not exist in the new-look Airport Utility. And the Airport Utility installation can’t be rolled back and the old utility won’t restore.
The sparesbundle is still not accessible. Anyone worked out a work-around in the new environment yet?
I have another Time Machine backup working fine to a trusty old Lacie Drive so erased the one on my Time Capsule to see if that works. I have renamed the Capsule and the Time Capsule Drive. But to build another full backup will take at least two days and I shall be away from tomorrow and am reluctant to leave the Capsule and computer up and running for a week. And I’ll bet the sparsbundle will still be nowhere to be found.
How can Apple screw up so badly when they are to become the richest company in the entire world and – soon – will have more cash in the bank than the entire United States? Can’t they afford someone who really can sort this out? Especially when a Firewire connected hard drive – my trusty and simple LaCie – works fine.
Words, almost, fail me.

Flash 9,0,124,0 security error after upgrade

I get the following error after upgrading my Flash Player
(after my system prompted me to install it while running the Flash
editor):
Internet Explorer has blocked this site from using an ActiveX
control in an unsafe manner.
I have uninstalled and reinstalled the player from the
browser, about 5 times now and it continues to be a problem for IE.
Works ok in Firefox if I manually download the FF installer. Is
there a standalone installer for Vista/IE7 or am I forced to use
the ActiveX installer which seems to have issues?

Fix: Removed both (!?more than one?!) versions of flash
player in my Programs and Features dialog, then ran
uninstall_flash_player.exe, reset IE7 to factory spec, then
reinstalled Flash from ActiveX. Seems to be working now.

TS1277 "iPhoto was unable to connect to Photo Stream" error after upgrading to mountain lion

Has anyone gotten this error after upgrading to mountain lion on a computer that already had a user setup on it?
My iphoto was working with photostream and now it will not connect at all.
I ran fix disk permissions and once it showed up in iphoto, photostream was loading and then it disappeared again.
help!

FWIW I fixed mine when I realised I'd probably downloaded iPhoto using an AppleID from the App Store but logged into iCloud with a different AppleID. I deleted iPhoto and it's related files (but not the iPhoto Library) using CleanApp, entered the App Store with my usual AppleID and downloaded iPhoto again. Once the App Store, the downloaded iPhoto and iCloud logins were the same iPhoto Stream worked again.

Error after upgrade CRS 4.0.4SR1 to 4.0.5SR2

Hi,
I've got some errors after upgrading my CRS 4.0.4SR1 cluster to 4.0.5SR2.
First my publisher's status stay in "patch" status for near 2 days now. I'm not able to change anything in the configuration, i've got this message "Config Changes are not allowed during 'Patch' operation, which was started by '_ccbu_build' at 'Thu Apr 08 04:31:04 CEST 2010 '. Please try again after 'Patch' is complete."(ERREUR02.jpg). How can I change this status?
Then I've got errors in historical DB which is working but not on the publisher only on subscriber. How can I resynchronize this DB?
Thanks for your help.

Thanks Tammy for the reply
We already tried the suggested SAP Note couple of time without any luck.
Regards,
SJ

Error after upgrading from sap b1 pl 35 to pl 49

hello sap experts
iam getting the following error after upgrading from sap b1 pl 35 to pl 49 this error is coming if we have given round off or discount in the below cell
"Discount deviates from authorised ranges (sales oreder-discount%for document) [message 439-15] pls make it as soon as possible an i will be thankful to those guys .
regards
Jenny

Hello Jenny,
You may check by supreuser account first to see if you got the same error. If not, it probably just related to user authorization. If yes, it must be a bug.
Thanks,
Gordon

What can I do if I get an internal power error after upgrading to Windows 10?

QuestionWhat can I do if I get an internal power error after upgrading to Windows 10?
AnswerSome laptops with AMD graphics that upgraded to Windows 10 are showing blue screens with error messages regarding Internal_Power_Error. If you receive this error, try the procedure in this article.
First, you'll need to quickly set the boot options to Safe Mode:
1. Hold the Windows key and press 'R' to open the run box.
2. Type MSCONFIG, then press ENTER.
3. Select the BOOT tab.
4. Under BOOT OPTIONS, check Safe boot, then select Minimal.
5. Click Apply, then OK.
6. Click Restart. (If prompted, click Restart anyway.)
From Safe Mode disable the AMD Display Driver:
1. Hold the Windows key and press the 'X' key to open a menu in the lower-left.
2. Click Device Manager.
3. Expand Display adapters to show the two display adapters.
4. Double click AMD Radeon R9 M200X Series.
5. Select the Driver tab.
6. Click Disable, then click Yes to confirm.
7. Click Close.
8. Hold the Windows key and press the 'R' key to open the run box.
9. Type MSCONFIG, then press ENTER.
10. Select the BOOT tab.
11. Uncheck Safe boot.
12. Click Apply, then OK.
13. Click Restart. (If prompted, click Restart anyway.)
From Windows 10 started with the AMD Display Driver disabled:
1. Hold the Windows key and press the 'X' key to open a menu in the lower-left.
2. Click Device Manager.
3. Expand Display adapters to show the two display adapters.
4. Double click AMD Radeon R9 M200X Series.
5. Select the Driver tab.
6. Click Update Driver.
7. Click Search automatically for updated driver software.
8. An AMD driver should be found and installed.
The driver that originally caused this problem is AMD display driver version 15.200.1046.2 dated 7/15/2015.
The driver installed through this process might have an older date, such as 15.200.1055.0 dated 7/6/2015. That's okay.

I'm having the same problem. I got error message 21. I went to apple store. they are saying i have a hardware error. Really, my phone was working before the update. Asked me for $150 to get another one when I am due to get a new one and wanted to pass this one on to my child.
Help please,
I will be glad to go back to the older software update

Imac error after upgrade to 10.8.4

I received an error after upgrade tp brand new imac. Error was upgrade was not installed. Upon reboot the version of SW in About thi Mac is 10.8.4. Bug?
iMac i7, 21.5" 16GB memory, fusion drive.
Thanks for input. I assume the upgrade took.

Verify Permissions gave me some errors, I deleted the repeats and the permissions fixed lines:
Repairing permissions for “Macintosh HD”
Warning: SUID file “System/Library/PrivateFrameworks/Admin.framework/Versions/A/Resources/readconf ig” has been modified and will not be repaired.
Warning: SUID file “usr/lib/sa/sadc” has been modified and will not be repaired.
Warning: SUID file “usr/bin/quota” has been modified and will not be repaired.
+++ (multiple repairs)
Permissions repair complete
I verfied the HD
Much text (removed)...
The volume Macintosh HD appears to be OK.
I also loaded the Apple downloads version of the upgarde and received the following (again):
The Installation failed
The insatllation encountered an error that caused the installation to fail. Contact the software manufacturer for assistance.
Message was edited by: Steve51K

NB305 - I have upgraded to 2GB RAM and Movie still look poor...

Hi
I recently bought an NB305 which i was hoping to watch movies on, however i started watching a standard def movie fromitunes and it slow and jumpy..
Ive upgraded to 2GB Ram with very little improvement..
Can this be fixed ? or am i best returning and getting an ipad ??
Many thanks
Simon

Numpty,
Im having the same problems and Im frustrated that everyone seems silent on all the threads I can find on this subject. I also upgraded to 2gb ram with no improvement on my itunes video performance and I'm just watching standard quality videos as well (instead of HD). I cant get through more than 1 minute of a Tv show from itunes without the sound going out and the video getting horribly choppy, requiring me to pause and let the video and sound get back on track.
I am using Windows 7 Professional. I have since tried to adjust my virtual ram (kicked it up to 3000mb), tried to adjust my video color quality (down to 16-bit), and tried playing the videos in Quicktime (which I figure has less memory requirements than itunes). None of these adjustments has helped. The only thing that might be working for me, though not a lot, has been to watch the videos in a very small window....but I'm starting to think Im just kidding myself with this even. I cant believe this isnt more of an issue for ppl. Its just weird that a little 2 year old ipod can play movies better than a brand new laptop, even if it is a netbook. I just ordered a recovery DVD from Toshiba to restore my comp to factory settings (i didnt make a backup before i installed Windows 7 Professional cuz im a $uck) and Im hoping that maybe some of the original video drivers or graphics settings might just work better....maybe I messed them up when I installed Professional, i dont know.
Input anyone?

Login Error after Upgrading from BW 3.5 to BI 7.0

Hi Experts,
We have carried out an upgrade from BW 3.5 to BI 7.0.
After Upgrade we are not able to login using SAP GUI. we are getting an error saying..
Username or Password not Valid..
During the upgrade (in Netweaver 2004s ) is there procedure necessary to be followed, which we could have missed..
Your response will be greatly appreciated.
Regards
LRaghunahth

Hi
Thanks a lot for your reponse.
Basically I am able to login thru sap* / ddic and can unlock the users / reset the password.
But the customer wants to know why the user is getting locked and it happened because of any procedure miss whil performing the upgrade..
if it is usual that users get locked during upgrade, any SAP Notes to refer..
Thanks a lot for helping in this community.
Best Regards
L Raghunahth

Facing Parse Errors after upgrading database from 10g to 11g

Hi,
We are facing parse errors in the SQL's after upgrading database from 10g to 11g.
Kindly look into below parse errors.
********************************** Parse Error *****************************************************
Tue Aug 13 14:13:08 2013
kksSetBindType 16173533-2: parse err=1446 hd=3c73061fb8 flg=100476 cisid=173 sid=173 ciuid=173 uid=173
PARSE ERROR: ospid=15598, error=1446 for statement:
SELECT ROWID,ORGANIZATION_CODE,PADDED_CONCATENATED_SEGMENTS,PRIMARY_UOM_CODE,REVISION,SUBINVENTORY_CODE,TOTAL_QOH,NET,RSV,ATP,ORGANIZATION_NAME,ITEM_DESCRIPTION,INVENTORY_ITEM_ID,ORGANIZATION_ID,LOCATOR_ID,LOCATOR_TYPE,ITEM_LOCATOR_CONTROL,ITEM_LOT_CONTROL,ITEM_SERIAL_CONTROL FROM MTL_ONHAND_LOCATOR_V WHERE (INVENTORY_ITEM_ID=:1) and (ORGANIZATION_ID=:2) order by ORGANIZATION_CODE,SUBINVENTORY_CODE,REVISION, organization_code, padded_concatenated_segments
Tue Aug 13 14:13:10 2013
kksfbc 16173533: parse err=942 hd=3c387c4028 flg=20 cisid=3266 sid=3266 ciuid=3266 uid=3266
PARSE ERROR: ospid=29813, error=942 for statement:
Select feature from toad.toad_restrictions where user_name=USER or user_name in ( select ROLE from sys.session_roles)
kksfbc 16173533: parse err=942 hd=3c97d83648 flg=20 cisid=3266 sid=3266 ciuid=3266 uid=3266
PARSE ERROR: ospid=29813, error=942 for statement:
SELECT password
FROM SYS.USER$
WHERE 0=1
kksfbc 16173533: parse err=6550 hd=35185e4278 flg=20 cisid=3266 sid=3266 ciuid=3266 uid=3266
----- PL/SQL Stack -----
----- PL/SQL Call Stack -----
object      line object
handle    number name
319e277050        30 anonymous block
319e277050        57 anonymous block
PARSE ERROR: ospid=29813, error=6550 for statement:
BEGIN sys.dbms_profiler."146775420110782746251362632012"; END;
kksfbc 16173533: parse err=942 hd=3c142d8600 flg=20 cisid=3266 sid=3266 ciuid=3266 uid=3266
----- PL/SQL Stack -----
----- PL/SQL Call Stack -----
object      line object
handle    number name
319e277050        67 anonymous block
PARSE ERROR: ospid=29813, error=942 for statement:
SELECT 1 FROM plsql_profiler_data WHERE 0 = 1
Please help.
Regards
Suresh

Hi Suresh,
Apologies for misunderstanding..
Tue Aug 13 14:13:08 2013
kksSetBindType 16173533-2: parse err=1446 hd=3c73061fb8 flg=100476 cisid=173 sid=173 ciuid=173 uid=173
PARSE ERROR: ospid=15598, error=1446 for statement:
SELECT ROWID,ORGANIZATION_CODE,PADDED_CONCATENATED_SEGMENTS,PRIMARY_UOM_CODE,REVISION,SUBINVENTORY_CODE,TOTAL_QOH,NET,RSV,ATP,ORGANIZATION_NAME,ITEM_DESCRIPTION,INVENTORY_ITEM_ID,ORGANIZATION_ID,LOCATOR_ID,LOCATOR_TYPE,ITEM_LOCATOR_CONTROL,ITEM_LOT_CONTROL,ITEM_SERIAL_CONTROL FROM MTL_ONHAND_LOCATOR_V WHERE (INVENTORY_ITEM_ID=:1) and (ORGANIZATION_ID=:2) order by ORGANIZATION_CODE,SUBINVENTORY_CODE,REVISION, organization_code, padded_concatenated_segments
Assuming you see the above error message in the alert log file, which was your original post, follow the below steps:
1 Get the 'ospid' value from the error
2. Issue the below command:
SQL> select request_id,ORACLE_PROCESS_ID
2 from fnd_concurrent_requests
3 where request_id = 15598;
3. After obtaining the request_id
4, Query it from the front-end using SYSADMIN responsibility
Hopefully this should get you the respective concurrent report/program.
Thanks &
Best Regards,

"The query was cancelled" error after upgrade from 10.1.3.3.3 to 10.1.3.4.2

Hi,
I was using OBIEE 10.1.3.3.3 /. After upgrading to 10.1.3.4.2 , the queries are not running ( long running queries alone) as expected. and so all the campaigns iwh tlong running queries are cancelled and the error message is seen in the xml log in Marketing jobs management.
We have upgraded the OBIEE version from 10.1.3.3.3 to 10.1.3.4.2 yesterday after which the connectivites have been checked with SQLPLUS and they are working fine. But when the campaign has been loaded, the Analytics have received the request for the segment query and after longer run, the task has been cancelled with the error message "The Query was cancelled as mentioned below in the Job Stats
<jobStats>
<jobID>2</jobID>
<jobType>WriteListFiles</jobType>
<jobUser>userid</jobUser>
<jobState>Error</jobState>
<jobTotalMilliSec>1h 41m 21s 160ms</jobTotalMilliSec>
<jobStartedTime>2012-03-22T08:06:13Z</jobStartedTime>
<jobFinishedTime>2012-03-22T09:47:34Z</jobFinishedTime>
<jobIsCancelling>N</jobIsCancelling>
- <exception>
<message>Job request of type "WriteListFiles" failed.</message>
- <exception>
<message>Error executing the list generation SQL.</message>
- <exception>
<message>Error in executing cursor for WorkNode (Id:0)</message>
- <exception>
<message>The query was cancelled.</message>
</exception>
</exception>
</exception>
</exception>
</jobStats>
Please let us know the suggestions
So far, the unaccessedtimingrunoutminutes tag has been tried to set 50 under ODBC tag in instanceconfig.xml. and the defaulttimeoutminutes has been tried to set to 150 in the same instanceconfig.xml.
along with that the rpd changes are done. For all the users apart from the Administrator, the timeout has been changedfrom 10 minutes to 150 minutes. But still that way is not working.
The segments was fired with the Administrator login. So , if the timeout for admin login can be set, i assume that the problem might be solved. Please let us know ur suggestions here too.
If that is the case, when we open rpd , only for Administrator user and group, the Permissions button is disabled. So i want to know how to change for Admin user settings in rpd..
Please advice us on the same.
Regards,
Madasamy M.
Edited by: Madasamy Murugaboobathi on Mar 26, 2012 1:40 PM

The issue has been resolved by setting the following parameters
<UnaccessedRunningTimeoutMinutes>120</UnaccessedRunningTimeoutMinutes>
<DefaultTimeoutMinutes>120</DefaultTimeoutMinutes>
<ClientSessionExpireMinutes>120</ClientSessionExpireMinutes>
<ConnectionExpireMinutes>120</ConnectionExpireMinutes>
<UIDefaultTimeoutMinutes>1440</UIDefaultTimeoutMinutes>

Build error after upgrading from 8.2.1 to 8.5 "Error 1055 occurred at Invoke Node..."

After upgrading to 8.5, I'm getting the following error when trying to build an EXE:
Visit the Request Support page at ni.com/ask to learn more about resolving this problem. Use the following information as a reference:
Error 1055 occurred at Invoke Node in AB_Source_Library.lvclass:Close_Reference.vi->AB_Build.lvclass:Copy_Files.vi->AB_Application.lvclass:Copy_Files.vi->AB_Build.lvclass:Build.vi->AB_EXE.lvclass:Build.vi->AB_Engine_Build.vi->AB_Build_Invoke.vi->AB_Build_Invoke.vi.ProxyCaller
Possible reason(s):
LabVIEW: Object reference is invalid.
I have been building this application for both Windows and Mac OS, and I even get the same error when building the .app on an Intel Mac.
Things that I've already tried:
* Mass-compiling all my code
* Created the project from scratch
* Enabled each panel of the "diagram disable structure" one at a time and compiled again
Any ideas?

Hi Travis,
Ben’s advice if definitely the best place to start. Error 1055 is a very general LabVIEW error for “Object reference is invalid.” The cause is usually a bad install where important LabVIEW function aren’t placed in the right directory or aren’t installed at all.
Charlie M. CLD

SSL Error after upgrading to Windows 8.1

After upgrade my Windows 8 to Windows 8.1, I got this SSL Error when I tried to go to "https://google.com":
http://i.stack.imgur.com/2kaXO.png
...and this in IE: http://i.stack.imgur.com/7Gxbw.png
I have did some research and tried to change my system time up to date, reset my modem and use wireshark to see if anybody is tracking my network, but none of them seem to be the problem.
Anyone can help me? Thanks a lot...
EDIT: I have checked my browsers and just figure out that every connection from my computer is not able to connect to any SSL connection, for example Yahoo Messenger login. I'm thinking my computer SSL Certificate got serious problem, is
there anyway to "reset" it?

Hi,
For the issue, it can happen for a wide variety of reasons.
I suggest we try the following methods to narrow down the issue.
Method 1.
Clear the Secure Sockets Layer (SSL) state:
In Internet Explorer, click Tools, and then click Internet Options.
Click the Content tab, and then click Clear SSL state.
Method 2.
Press Win+X, and then click Command Prompt(Admin).
At the command prompt, type sfc /scannow, and then press ENTER.
Method 3.
Press Win+R, type regedit in the box, and then press ENTER.
Locate and then click the following registry subkey:
HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Internet Explorer\Main\FeatureControl
On the Edit menu, point to New, and then click Key.
Type FEATURE_ERROR_PAGE_BYPASS_ZONE_CHECK_FOR_HTTPS_KB950067 to name the new registry subkey, and then press ENTER.
On the Edit menu, point to New, and then click DWORD Value.
Type iexplore.exe to name the new registry entry, and then press ENTER.
On the Edit menu, click Modify.
Type 1, and then click OK.
Exit Registry Editor.
If the issue persists, I suggest you reinstall the IE to check the result.
Hope these could be helpful.
Regards,
We
are trying to better understand customer views on social support experience, so your participation in this
interview project would be greatly appreciated if you have time.
Thanks for helping make community forums a great place.

Satellite L30-10Y: Checksum error after upgrading to 2Gb RAM

Similar Messages

Maybe you are looking for