Satelllite A50 problem with install new OS

Hi there,
I,ve got tiny problem :)
Forgot how to eneter to bios system :D simple i don't remember Key Configuration.
Can anyone help?
Best Regards.

You must be kidding! :D
If the notebook supports an Toshiba BIOS I would recommend using the ESC button and then F1

Similar Messages

Problems with installing new programs

Dear all,
since the update to OS X Yosemite, I have some problems with installing new programs.
I tried to install the Fitbit App to connect my Fitbit to my Mac but the program can't be started after installation. I have the same problem with Blackberry Blend, too. I am able to install it but it doesn't start running.
Does anybody have an idea what's the problem?
Thank You,
Lisa.

Did you receive any errors during the installation itself or does this happen when you try to open Photoshop?

Problem with installing new software !!!!!!!

Hello!!
I got a message that there is new version of ipad software..
I've wanted to update, and then my problems started.
First it couldn't install new version, then it said I have to restore software, and now it can not restore the software on my ipad.
I connect ipad with itunes, it say: resotring ipad firmware... I see on my ipad line around 70% and that is all.
after one hour it is still 70% restored. I can not do anything.
I can not turn on ipad (I can only connect with itunes), but it won't restore a software.
should I leave so, maybe after 8 hours will come to end. or..???
thanks in advance.

Try placing the iPad in Recovery mode and then restorinf via iTunes.
Next would bne to try DFU mode
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings

Problem with installing new line card 7600-SSC-400

Hi all,
I have a trouble when trying to install new line card 7600-SSC-400 on Cisco 6509. Here was the message displays on the screen after I finished installing the line card : "%C6KPWR-SP-4-UNSUPPORTED: unsupported module in slot 7, power not allowed: The image for the card is not bundled in image." I tried to install this line card on another slot, but it doesn't work. The attched item is logfile which I saved in the installing session. I don't know what I hvae to do now, please help me to resolve this problem !
Thanks so much,
Hieu

Hi Hieu,
You might want to run the following to see more detail of the error:
show diagnostic result module all detail
And I would also suggest that you reseat the 7600-SSC-400 line card firmly back to the switch, and check the status again.
If it's still showing the error, maybe you can try seating the module on a different slot, and check if you have the same issue.
If the issue still persist after reseating and testing it on different slot, then it might be a hardware issue, and you might want to open a TAC case to further investigate it.
Hope that helps.

Problems with Installing New Harddrive on SL510

Could really use some help trying to diagnose the problem and a best way to try to resolve:
I have a Thinkpad SL510 that was beginning to have blue screen issues and diagnostics indicated HD needed replacement. Purchased a 500GB SATA HD to replace my old one. Was not able to create a system image (kept getting an error that prevented this), so I did create recovery & boot discs from Lenovo Recovery. Since installation and running recovery/boot discs, I'm having several problems:
- I cannot run windows update. Keep getting this message: "windows updates cannot currently check for updates because the service is not running. You may need to restart your computer".
- I'm also unable to connect to the Quickbooks Server to download updates from them as well.
- Two errors on Device Manager: (1) Realtek PCIe GBE Family Controller (fixed this), and (2) SM bios service (cannot fix). Each of these indicated "Windows cannot verify the digital signature for the drivers required for this device. A recent hardware or software change might have installed a file that is signed incorrectly or damaged, or that might be malicious software from an unknown source. (Code 52)"
- Cannot run troubleshooting. Keep getting this error message "0x8E5E0247"
Could really use some help to identify what is making this happen and what might remedy the problem.
THANKS!

Hello and welcome,
The windows update problem likely comes from installing an advanced format HDD. (That's about all you can get these days).
It's fixable. Some suggestions and links in this thread: http://forums.lenovo.com/t5/T61-and-prior-T-series-ThinkPad/Problems-after-installing-Windows-7-Prof...
Z.
The large print: please read the Community Participation Rules before posting. Include as much information as possible: model, machine type, operating system, and a descriptive subject line. Do not include personal information: serial number, telephone number, email address, etc. The fine print: I do not work for, nor do I speak for Lenovo. Unsolicited private messages will be ignored. ... GeezBlog
English Community Deutsche Community Comunidad en Español Русскоязычное Сообщество

Problems with installing new hard drive using time machine

Hi,
I have a 2.4 GHz Intel Core 2 Duo 15" Macbook Pro (unibody) with 8 GB 1333 MHz DDR3 and a 250 GB Sata HD running OS 10.6.7.
It works like a dream.
However, i bought a new 1 TB HD (WD Scorpio Blue) since a) 250 GB is not enough for me right now b) warranty has expired, so new risk there and c) i read that installing it would be very easy.
I'll try so explain what i did, see if anyone finds what could be wrong...
I had some minor problem in the beginning (i didn't use the install disk of the macbook pro at first, because it was at the office, so i used the install disk of my old Alu iMac), but using the right disk, i opened "Restore Disk from Backup", selected the Time Machine disk, and waited for the target drive to appear. It didn't...
Finally i figured, maybe he doesn't find it because it hasn't been formatted yet (although it says on the HD that the Scorpio Blue is ready to use as is). So i openen disk utility from the utility folder and formatted the disk as "OS Journaled". As expected (?) the disk appeared as a target Restore Disk. I selected it and "restore" started. It took some hours and finally i receive a message: restore complete (or something like that). But then... after the restart i say the apple logo (as always) followed by the 'i don't know how you call it'-screen: a grey screen coming down like a curtain that says something like: you have to hold down the power button and then press it again tot restart (in a dozen or so languages including mandarin or japanese...). Off course i tried to restart several times, always with the same result.
I switched back to my old drive and it still works like a dream ;-)
So now i'm typing this message, can someone point out to me what could be the problem?
Some more information/possible causes:
- i run snow leopard, but the install disk is leopard. Maybe i should have used the install disk of the Snow Leopard i bought?
- the time machine backup backs up EVERYTHING including an external firewire disk (on the same disk). Maybe that could be a problem? I don't know if the backup disk will restore the content of my external disk to my new internal HD or not...
Thanks for helping me out...
Best regards,
Tom

Hold on... it seems like i missed the obvious answer: using snow leopard to re-install a snow leopard back up. I'll try that one first and if it doesn't work i'll come back to this discussion...

Problems with installing new update 10.4.0.80

Hello all. Running Windows Vista. I have recently updated my itunes to 10.4.0.80 - no problems . I have now updated itunes on my husband's computer. It downloads without a problem, and gets really near to the end of the "green progress bar" whilst installing, and then I get a message saying "errors encountered - go to tools, download and install manually". I have checked everything I can think of - cookies cleared, disc clean-up, defrag - you name it I have done it! I have the latest update of safari, quick time is showing as the latest version, so I really cannot understand what the problem is Please, can anybody throw any light on this for me. I am beginning to think that I should perhaps backup all the music to disc and then uninstall and then reinstall , but this is going to be quite a job, so I don't want to start this if somebody has got a better idea. All suggestions will be very gratefully received. Many thanks.

What an absolute mess this upgrade is! I have just spent ages reading all the postings regarding the failings of this new version. I have also realised that this is probably why my daughter's iphone will not now update. I think I am just going to leave well alone and wait for apple to sort themselves out. Could I just ask one more question please, I have an external hard drive which I have used to back up photos etc. When I tried to backup itunes it seemed just to save a shortcut to who knows where which would not actually open. I have checked on itunes and under library, I have an option to export library - is this what I need to do to save it to the external hard drive? I am not very good with computers so I am really nervous about doing this. Are you also saying that although I have not knowingly backed up itunes in the past, that all music in my library is stored somewhere on my computer and if I do uninstall and reinstall itunes, that information will automatically be added once I reinstall?

Problems with installing new RAM on P45C Neo-FIR

I have an MSI "P45C Neo-FIR" motherboard with 4GB (2x2GB) DDR2 800Mhz ram.
In order to upgrade my computer I bought 2 sticks of 4GB DDR3-10600 (KVR13N9S8/4) but when I install them my computer won't boot, it beeps 3 times and then shuts itself down.
I tried updating the BIOS version but it still doesn't work...
What could be the problem? I'm pretty sure this memory is compatible with my motherboard...

Quote from: vitalgrados on 01-May-13, 15:55:14
In order to upgrade my computer I bought 2 sticks of 4GB DDR3-10600 (KVR13N9S8/4) but when I install them my computer won't boot, it beeps 3 times and then shuts itself down.
I'm pretty sure this memory is compatible with my motherboard...
I'm not so sure about that compatibility.
http://ark.intel.com/products/35133/Intel-82P45-Memory-Controller-Hub
The P45 chipset is limited to DDR2-800 or DDR3-1066
With a voltage bump it also works (more or less stable) with DDR2-1066 and DDR3-1333
But DDR3-1333 is not an option in case of 2 x 4GB.
You need DDR3-1066 modules if you want 8GB RAM on P45.

Problems with installing new itune, different from the problems described.

Ok, so this morning when I was trying to access itunes, it said "error, send error report" or something like that. I retried it several times, but it would not work. So I uninstalled it and installed the new version. Then, I when I was trying to download it, it said something is wrong with my "Windows Installer Package"...and it just skips installing itunes... Please help me, thank you.

Then, I when I was trying to download it, it said something is wrong with my "Windows Installer Package"...and it just skips installing itunes
instead of running the install on line, download and save a copy of the iTunes installer to your hard drive, and run the install from there.
if you still get the message then, could you post back with the precise text of the message?

Unique problem with installing new version of adobe flash player

Hi there. I am unable to install the newest version of adobe flash player. I am not getting any error messages like most people's issue on this forum. What happens is I run the installer, and it attempts to install for a second and then the installer screen goes blank , as you can see in the image. nothing happens after this. I have tried uninstalling and reinstalling. Any tips on why this is happening?

Hi Casey,
When did you download this file? It is for a problematic installer that we removed from our servers last week (Wednesday 25-March). If it's still being downloaded it's either cached on our servers and we need to clear the cache again, or it may be cached by your browser, in which case, clearing the browser cache will download a new, non-problematic installer.
Thank you in advance.
Maria

Problems with installing new versus of Creative Suite 5.5

Disk 1 does not eject at the end of the installation process, when the installer ask for Disk 2

open your file explorer/finder>right click your disk drive>click eject.
if you don't have a cd eject option, use google find a free app that adds that functionality.

Has anyone in this Forum had problems with installing and running Adobe apps on the new MacPro?

Has anyone in this Forum had problems with installing and running Adobe apps on the new MacPro?
I have been trying to install Photoshop CS6 & CC and Acrobat Pro XI on my Mac Pro (late 2013). I keep getting a 'configuration' error message and wondered if the problem was wide spread.
TIA,
Jerry

Thanks, Martin.
Good to hear someone has had success. The lack of it here is frustrating and depressing.
Thanks again,
Jerry

Problem with install on new compy, something to do with external?

Hello, so I have been having a few problems with installing Arch on my new computer. On my old laptop I never ran into this problem on any distro of LINUX I installed, nor on any other of the systems I have installed Arch on. I believe it might have something to do with the fact that I am running the live cd off of an external dvd drive maybe? I am kind of stuck here, so any help would be greatly appreciated! Thanks!
If it helps
System Specs:
Motherboard: ASROCK 890FX Deluxe3
Processor: AMD Phenom II X4 955
Graphics Card: ATI Radeon HD 5700 Series
Hard Drives: 2 SATA 160gb hd RAID 0, and one 160gb ATA hd
OS: Windows 7 Professional on the RAID 0, hoping to put ARCH on the ATA (I have tried booting the ATA first in the list behind the USB DVDROM to no avail)
External Drive: Sony DVD/CD RW drive DRX-510UL
External DVDROM is the exact same drive I used to install windows 7 professional.
External DVDROM is plugged into one of my USB 2.0 ports, but the error still persists.
I am using the EXACT same disk I used when installing it on my past computer.
Trying to install x86_64 version of Arch, gets past the splash.
Output that I could catch:
:: Running Hook [archiso]
:: Rinning Hook [archiso_pxe_nbd]
:: Mounting tmpfs, size 75%... done.
:: Waiting for boot device...
Waiting 30 seconds for device /dev/disk/by-label/ARCH_201005 ...
usb 9-1 : device descriptor read/64, error-62
usb 9-1 : new full speed USB device using ohci_hcd and address 3
usb 9-1 : device descriptor read/64, error-62
usb 9-1 : device descriptor read/64, error-62
usb 9-1 : new full speed USB device using ohci_hcd and address 4
usb 9-1: device not accepting address 4, error -62
usb 9-1 : new full speed USB device using ohci_hcd and address 5
usb 9-1: device not accepting address 5, error -62
hub 9-0:1.0: unable to enumerate USB device on port 1
scsi 6:0:0:0: CDROM SONY DVDRW DRU-510A 1.0d PQ: 0 ANSI: 0
scsi 6:0:0:0: Attached scsi generic sg3 type 5
sr0: scsi3-mmc drive: 32x/32x writer cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
ERROR: boot device didn't show up after 30 seconds...
Falling back to interactive prompt
You can try to fix the problem manually, log out when you are finished
/bin/sh: can't access tty; job control turned off
If you need any other info, I can grab it of course.
Last edited by crusniknano (2010-07-12 19:49:13)

K, got it running. was having errors with the USB hd, but just changed the name it booted from to the name of the drive. thanks!

[SOLVED][GRUB]Install problem with the new method

Hi,
it is not my first install of Arch Linux but I have a problem with this new kind of installation method, especially with GRUB.
Here is my hard drives configuration :
/dev/sda1 -> SSD 120 GB ntfs (windows)
/dev/sdb1 -> HD 1 TB ext4 (data)
/dev/sdc :
/dev/sdc1 -> ext2 /boot
/dev/sdc2 -> swap
/dev/sdc3 -> ext4 /
/dev/sdc5 -> ext4 /home
During the installation, I installed grub (with grub-install) in /dev/sdc. I assumed it was the correct drive to install it but apparently not, Windows starts automatically and I don't have the grub menu.
Should I install my system again or is there a way to boot on the livecd and install it ?
Should I :
1) mount /dev/sdc3 in /mnt then /dev/sdc1 in /mnt/boot and finally /dev/sdc5 in /mnt/home
2) pacstrap /mnt grub-bios
3) arch-chroot
4) grub-install
Thank you.
Last edited by hiveNzin0 (2012-09-12 06:15:15)

DSpider wrote:
If you set whatever drive "/dev/sdc" is (brand and model) to boot first in the BIOS, all you need to do is install a bootloader on Arch. You don't even need a separate boot partition. It will use the /boot folder on root partition. Then install os-prober (if you don't already have this installed) and re-generate the .cfg.
https://wiki.archlinux.org/index.php/Be … bootloader
The problem is that I cannot select another hard drive. The only one available for the boot order is the Samsung 830 series (/dev/sda with Windows).
The other options are the CD drive and removable disk.
I checked that this morning, maybe I was too tired. I will check again this evening.
But if I am right and I cannot select my intel SSD (containing my arch setup) for the boot order, would the solution I described work ? I don't see why not but my knowledge are basic in Linux.
Thank you again for your help.

Problem with the new server UCS C220 for set IP to CIMC

Hi
We’ve a problem with the new server UCS C220.
We bought two servers UCS C220 M3 for CallManager 8.6 with High Availability.
When we turn on the server during the boot and when it tells us, oppress F8 to enter at the CIMC and set the IP. But it never enters at the CIMC.
Then, we configure our DHCP server and our switch, we connect the three gigabyte ports to our switch to give him an IP to the CIMC, so and then can enter via browser, but neither works.
Note. The dedicated management NIC does not link, the other two ports do make link.
What do you suggest to put an IP to CIMC and start installing our applications?
regards

You may have noticed that there is no DVD rom on the c220. What you need to do is:
Login into the CIMC from your browser
Luanch the KVM
Insert the VMware DVD in your machines drive
On the KVM pop up there should be a tab to mount the drive, after mounting it click on Macros and choose ctrl_alt+delete to restart.
After the VMware OS installs press F2 to enter IP.
Browse to the VMware ip to download the Vsphere client
Open the Vsphere client, enter the ip of the vmware and the username will be root and no password if you did not set one.
You can now upload OVA templates or manually create virtua machine from this enviroment.
Hope this help

Satelllite A50 problem with install new OS

Similar Messages

Maybe you are looking for