SCA design question - PIX and SCA with dual logical SSL server.

I have a SCA design question. please correct or verify my solution.
1. connectivity.
<Client with port 443>--<ISP>--<PIX>--<SCA>--<SERVER(two IP on single NIC and each IP associates to WEB server) with port 81>
* client will access WEB server with x.x.1.100 or x.x.1.101
2. physical IP address
- PIX outside=x.x.1.1
- PIX inside=x.y.1.1
- SCA device=x.y.1.2
- SERVER NIC1=x.y.1.10
- SERVER NIC2=x.y.1.11
3. PIX NAT
- static#1=x.x.1.100 map to x.y.1.10
- static#2=x.x.1.101 map to x.y.1.11
4. SCA configuration.
mode one-port
no mode one-port
ip address x.y.1.2 netmask 255.255.255.0
ip route 0.0.0.0 0.0.0.0 x.y.1.1
ssl
server SERVER1
ip address x.y.1.10
localport 443
remoteport 81
server SERVER2
ip address x.y.1.11
localport 443
remoteport 81
Thanks,

The document http://www.cisco.com/univercd/cc/td/doc/product/webscale/css/scacfggd/ has a link to a page which describes how to use the configuration manager command line interface to configure the Secure Content Accelerator. Several configuration examples are also included in this page.

Similar Messages

  • Certification sample questions: Planning and Manufacturing with GATP

    Dear Certified Folks
    I have a certification exam in planning and manufacturing with gATP in couple of weeks from now. Could someone help me direct to some sample questions (other than the ones available on sap.com/education page) in case some kind consulthropist has maintained such a thing. I googled a lot but didnt land any. But not everything is available on google. I sincerely want to evaluate myself and accrodingly revise or postpone the test.
    The sample questions I attempted on sap educaiton pages looked so vague and simple at the same time that I felt no one can go wrong but I got 5 in 10 wrong. To feel good, accounting for mutiple correct answer ones I got 9 of 14 right options in 10 questions right. If these are the kind of questions in final test, I will definately fail .. fixed scoring or scaled. I mean even If I study thrice over I will fail. I am purely educating myself on the system I have access to doing F1's and help.com plus some practical experience of a couple of "modules"
    So please help, guide. share some strategies
    Thanks
    Guru

    Thank you Ravi for the advise.
    Pardon me for my curiosity but certified consultants in a community forum like this is something that to be certified aspirants will naturally look forward to for guidance, tips and experiences and some tough questions as challenges from seniors. The same as we do in schools all over the world incl, third world countries. if this is not the purpose of this forum then I wonder what else is. Other information is available on sap wesbites.
    I appreciate the fact that I cant pass exams with sample questions. There are enough bogus lords outsides trying to sell their SAP wares on the platter. but I dont need them to pass the test. If that were so in the past I would not have cared to registered here
    Apologies for breaking the rules of this forum, albeit inadvertently.
    I will see how can I help myself.
    Regards
    Guru

  • Question about mac mini with Mac OS X Server

    Hello forum,
    first I want to say hello to each, because this is my first post in this forum.
    I want to buy a mac mini, but I have further questions before i buy.
    My Situation is, that currently I have a windows and a linux server (Windows => Exchange and Linux as a build server). Now i want to remove such servers and replace it with one mac mini server.
    1.) Currently I have an exchange server...Is it possible to use Mac OS X Server to work like an Exchange server?
    2.) I plan to use it as a build server which generates bundled software for Mac OS, Windows and Linux (Windows and Linux where running in VMWare Sphere)
    Is this possible with it?
    Thanks in advance
    Best Regards
    Roman80

    1.) Currently I have an exchange server...Is it possible to use Mac OS X Server to work like an Exchange server?
    That depends on how deeply-embedded you are into Exchange.
    If by 'Exchange' you mean the basic email/messaging tools then yes, but if you mean the full MAPI client/SharePoint/messaging/sync/compliance tools then no.
    2.) I plan to use it as a build server which generates bundled software for Mac OS, Windows and Linux (Windows and Linux where running in VMWare Sphere)
    This isn't an option. vSphere will not install on a Mac Mini. The only VMWare option for the Mac Mini is VMWare Fusion, which does allow running client OS systems in a virtual machine, but does not support the full suite of VMWare functionality. Whether it has enough for your needs cannot be determined without more details of how you expect this to work - if it's just a matter of having a Visual Studio running in a Windows VM, and some other compiler running in a Linux VM then it may be possible, it just depends how deep you need to go.

  • Mac and Windows with dual monitors Question

    I use a Intel MacPro running Tiger with latest updates in my church. We use the Mac and Keynote 2.0.2 to present PowerPoint slides on the big screen (dual outputs). Everything was going well until the pastors upgraded to new computers running Vista and Office 2007. Now neither pastor's files will load into Keynote. It comes up with an error. The pastors have saved their files from PP as 2003 PPT files, and they still will not open. Error - unable to open file type. The one pastor went back to XP (dumped Vista) but still used the Office 2007 program and saved as PP2003, but the error still appears.
    FYI - I noticed that Office 2007 saves with a file with the extension of .pptx instead of the .ppt. Checking the file they gave me shows that it is indead a .ppt file and not .pptx file. It makes no difference.
    I believe it is an Office 2007 problem I'm dealing with. I have taken the .ppt file and loaded it onto the PC running PP 2003 and it loads fine, except for some format problems. I then resave it with a different name and tried to load that file (hoping it was converted) , with the same error showing. The problem is transfered with the file. Other files created with the PP 2003 program load fine into Keynote, so it has to be the Office2007 doing something.
    So the questions are, is there an easy fix and still use the Keynote program, OR does Keynote 3 take care of this problem in the upgrade, OR should I install Win XP home or Pro and use parallels (which I have)? Would WinXP Home be enough to support the dual outputs and be fast enough? I am familiar with XP Pro not Home.
    Any information you may have, could be a help. I need this resolved soon. I hate having to bring in the old Windows PC, after enjoying the quality of the Mac.

    David.Austin.Allen wrote:
    You should not have issues attaching two displays to the Mac mini. You will not be able to use an iPad as one of those displays.
    I have no issues streaming video on demand from all of the media sources which you have listed. My Mac mini is the Early '09, so my hardware is not as powerful as the newest Mac mini.
    Dah•veed
    Thanks David - glad to here the Mini supports dual monitors, and you're not having any streaming issues. Did you have any special settings, like "no hardware acceleration"? Are you streaming HD content?
    If it supports dual monitors, then I would think the iPad could be used as a second display and input device - the demos I've seen with Air Display (from Avatron Software") would accomplish what I'm looking for. Here is a demo at http://www.vimeo.com/16950420 showing the iPad working with a Windows machine, but I've seen them working with Macs as well.
    Thanks again
    Michael

  • Design question, UCS and Nexus 5k - FCP

    Hi,
    I need some advice from (Mainly a Nexus person); I have drawn and attached the proposed solution (below).
    I am designing a solution with 3 UCS chassis, Nexus 5K and 2X NetApp 3240 (T1 and T2). FC will be used to access disk on the SAN. Also, Non UCS compute will need access to the T2 SAN only. (UCS will access T1 and T2). It is a requirement for this solution that non UCS devices do not connect to the same Nexus switches that the UCS chassis use.
    UCS Compute:
    the 3 X chassis will connect to 2 X 6296 FIs which will cross connect to the a 2 X Nexus 5K through a FC port channel, the Nexus 5Ks will be configured in NPIV mode to provide access to the SAN. FC from each Nexus 5K to the NetApp controllers will be provided through a total of 4 X FC Port Channels (2 FC member ports per PC) from each nexus 5K one going to controller A and the other to controller B.
    Non UCS compute:
    These will connect directly through their HBAs to their own Nexus 5Ks and then to the T2 SAN, these will be zoned to never have access to the T1 SAN.
    Questions:
    1-      As the UCS compute will need to have access to the T1, what is the best way to connect the Nexus 5Ks on the LHS in the image below to the Nexus on the RHS (This should be FC connection).
    2-      Can fiber channel be configured in a vPC domain as Ethernet? Is this a better way for this solution?
    3-      Is FC better than FCoE for this solution? I hear FCoE is still not highly recommended.
    4-      Each NetApp controller is only capable of pushing 20GBps max, this is why each port channel connecting to each controller is only 2 members. However, I’m connecting 4 port channel members from each Fabric Interconnect (6296) to each Nexus switch. Is this a waste? Remember that connectivity form each FI is also required to the T2 SAN.

    Max,
    What you are implementing is traditional FlexPod design with slight variations.
    I recommend to look at FlexPod design zone for some additional material if you have not done so yet.
    http://www.cisco.com/en/US/solutions/ns340/ns414/ns742/ns743/ns1050/landing_flexpod.html
    To answer your questions:
    1) FC and FCoE do not support vPC. If UCS needs to have access to T1, then there is no need to have ISL between sites. If UCS needs to have access to T1 and T2, then best option would be to set up VSAN trunking on N5K and UCS and configure vHBAs accordingly.
    2) Both should work just fine. If you go with FCoE, then UCS would need to be on the latest version for multi-hop FCoE support.
    3) If you only worried about storage throughput then yes, you will never utilize 40Gb PO if your source will be 20Gb PO. What are your projected peak and average loads on this network?

  • Why does the file size change when put into an iDVD project? And problems with dual layer discs...

    I exported a short video of mine from Final Cut Express and the size of the file came out to 7.3 GB. When I put it into an iDVD project, it says that the file is only 800 MB. I tried just burning it onto a dual layer disc anyway to see if it might still burn at the original file size, but the disc came out unusable for some reason, and obviously hadn't been burned anywhere near full-capacity. So, I tried it again, and the exact same thing happened.
    I guess my first question is: why is iDVD changing the size of the file? I want the quality to be the best it can be, so keeping it at 7.3 GB as opposed to 800 MB is rather important.
    Secondly, why did the dual layer discs come out unusable? I've burned single layer discs before and they haven't been an issue. Also, I know for a fact that the drive can burn dual layer discs, so that isn't the issue.
    Thanks in advance to anyone who can provide me with help on this issue.

    LivelyJamesS wrote:
    I exported a short video of mine from Final Cut Express and the size of the file came out to 7.3 GB. When I put it into an iDVD project, it says that the file is only 800 MB.
    Guessing here but it looks like you edited/exported an SD/DV sequence of about 30 min in FCE. DVD needs to be MPEG-2 so iDVD compresses the original file down to the size that you report.
    LivelyJamesS wrote:
    I guess my first question is: why is iDVD changing the size of the file? I want the quality to be the best it can be, so keeping it at 7.3 GB as opposed to 800 MB is rather important.
    The quality will be what the MPEG-2 compression and the software allow for. MPEG-2 is DVD standard .... there's no way around that.
    LivelyJamesS wrote:
    Secondly, why did the dual layer discs come out unusable? I've burned single layer discs before and they haven't been an issue. Also, I know for a fact that the drive can burn dual layer discs, so that isn't the issue.
    Guessing again but it would seem that you burned a Data DVD instead of a Video DVD which would be unusable by a set-top player. As I said above you can't get around DVD standards.
    If by any chance your video was HD originally you can try to go the Blu-Ray route using Roxio Toast or FCS 3 (discontinued) or FCP X. You will also need a Blu-Ray burner.

  • Design Question - BPM and dynamic JDBC adapters

    Hello,
    I need help to finish my scenario.
    scenario:
    step1 : Idoc > PI(7.1)  <>  JDBC stored procedure call
    step2: If the Sync. JDBC call is successful  then make a sync. BAPI call  to R/3.
    step3: If JDBC all fails ( in step 1 ) it should tigger an emial and do not make BAPI call ( do not execute step 2).
    I have 200 SQL servers and each time IDOC goes to any one of these 200 servers  ( yes, only one server ) , depending on the connection parameters in one of the idoc segment.
    Questions:
    1. Can we do this without BPM?
    2. can we configure dynamic JDBC adapte depending on the login credentials in IDOC ( server name, port, user name , passwore).
    3. If dynamic JDBC adapter configuration is not possible, what should be my design. Do i need to create 200 communication channels and 200 rec. determination, 200 interface determination, 200 receiver agreement..I dont think this is a good design

    Hello,
    It seems doable without using BPM.
    step1 : Idoc > PI(7.1) <> JDBC stored procedure call
    step2: If the Sync. JDBC call is successful then make a sync. BAPI call to R/3.
    You can use a two-step mapping.
    1.) The first one calls the stored procedure using UDF or Java Mapping (as was suggested in earlier threads)
    2.) The input to the second mapping will be the response from 1. You can use RFCAccessor to execute the BAPI.
    step3: If JDBC all fails ( in step 1 ) it should tigger an emial and do not make BAPI call ( do not execute step 2).
    Use XI/PI alerting framework for failed messages. The BAPI call can/cannot be executed by using a try-catch statement in the root node of 2nd mapping (1..1 occurrence), return suppress in the root node if conditions are not met or return a value if otherwise.
    Note: Consider this blog in your design, /people/thorsten.nordholmsbirk/blog/2008/11/04/why-xi-mappings-should-be-free-of-side-effects
    Hope this helps,
    Mark

  • Screen Sharing issues with ML and SL  with dual displays??

    Don't know if this is a ML issue or was present in Lion (which I never upgraded to)
    Setup...
    Old setup was 2010ish MBP and only 2006 iMac.  Both with SL 10.6.8 and both have two monitors...no issues.
    Upgraded to ML on the MBP on release.  Realtively painless process.  I tried screen sharing today and I get odd responses with the MBP to the iMac.  Just so everyone knows, screen 1 is the main iMac screen and screen 2 is the additional monitor.  When showing both screens I could see all screen realestate.  However, when I changed to only display screen 1 I started having issues.  I couldn't get the entire screen to fit within the window nor scroll to show areas not displayed.  Sometimes switching between fit in window and no fit, I would get a blank screen.  Screen 2 only displayed and all is fine.  I noticed on screen 1 that there was a little black bar or open space on the bottom of the window that was exactly the same size that was missing from the top.  No ability to fit or scroll would allow the black space to move so that the menu bar on the top of the main monitor would display.
    After doing a bit of searching with no luck and scratching my head, I took a look at the Arrangement screen in the display settings.  Wouldn't you know it that the main screen (having a smaller resolution than screen 2) was aligned so that the top of each display was even with each other leaving a small space on the bottom of screen 1 compared to screen 2.  When I moved screen 1 in the arrangement screen to a more drastic alignment to verify this was the problem...screen sharing crashed when going from both screens to only display screen 1.  Tried screen sharing again going from two displays to one, crashed again.
    It appears there is some sort of bug or maybe ML and SL screen sharing doesn't like each other when the remote computer has two monitors.
    Submitting bug report to Apple but was curious if anyone else has seen this or knows a work around.
    Mike

    I have a similar configuration (Lion 2011 MBP and SL 2009 iMac w/ second display). After installing the recent Remote Desktop update things went awry when trying to share the iMac SL displays with the MPB Lion.
    The displays on the iMac are the same resolution, however the second display physically sits a bit lower than the iMac display, so I had adjusted the arrangement to compensate the different heights. The second display is located physically to the left of the iMac display, but that shouldn't have any effect as far as I'm concerned. Screen sharing had worked in this config until the recent Remote Desktop update (on Lion).
    I thought about what you mentioned about the display screen arrangement, so I decided to just test it for myself, arranging both displays side-by-side on the displays arrangement control panel. Surprisingly, it worked!
    I do consider the Remote Desktop update to be the culprit and there must be some bug associated with that. I'm getting ready to submit a bug report, so hopefully we'll see a fix soon.

  • Design Question - Reusable WebService Client with UI

    Hi,
    How to design, and package a web service client so that it would be a reusable ADF component?
    Recently, I have been working on a web service client. I have used a Java proxy and exposed this java proxy as a data control, and have used this (drag & drop) on a jsf fragment page.
    However, there might be a strong situation where other teams on this program would be using it, instead of they reinventing the wheel, I was thinking they could reuse this.
    Having said that, and searching this forum, I am not sure to package, or what additional things to to so that it is cleaner to expose this component for reuse.
    Any direction is greatly appreciated.
    Thank you,
    VJ

    Hi,
    create a bounded task flow that contains UI in a page fragment (for this you need to create the bounded task flow to use page fragments, which is a setting when creating task flows). The package the whole bounded task flow in an ADF library (create a new deployment profile --> ADF library). This then packages the data control and the UI.
    http://download.oracle.com/docs/cd/E17904_01/web.1111/b31974/reusing_components.htm#BEIGHHCG
    Frank

  • New video posted on IAC Driver configuration and use with Mainstage/Logic

    Shows how to configure IAC Driver for use with Mainstage and Logic.
    http://www.youtube.com/watch?v=wPhtRCwz8vs

    No problem, anytime...
    Yes, that should work. I haven't specifically tried that but don't see why it wouldn't work so give it a go. When I was testing this IAC driver method, I did confirm that the IAC object existed in the environment in Logic and it did, so you should be good to go.
    You're exactly right, both Logic and Mainstage should be active. You'll get a message saying another Rewire host is active when you open both, but just click ok and ignore it.
    Here are a couple of other vids as example of what you can do with the IAC driver just to keep your brain burning
    http://www.youtube.com/watch?v=XgzBOJYSY64
    http://www.youtube.com/watch?v=NZL0ucV8dpo
    If I have time I'll try to test it as well, it's a good idea!
    Let me know how it goes or if you have any questions.
    J.

  • Not able to install Logic on mac with OSX.  10.8.2. Error message: Logic Studio.mpkg cannot be opened as the power pc programs are no longer supported. I have logic studio 8 software purchased in 2007 and upgraded with logic studio 9 (purchased in 2009)

    After an earlier attempt to move Logic from my other mac (OSX 10.6.8) with the migration assistant to my new mac with OSX 10.8.2. I've re-started the whole start up process by erasing the hard drive from the new machine and build it up from scratch. After a new "out of the box" start, I decided to install LOGIC from my disks : starting with my 2007 package Logic Studio 8 and upgrading with my Logic 9 package from 2009. When trying to start to install 2008 I got the error message : Logic Studio.mpkg cannot be opened as the power pc programs are no longer supported.
    What does this mean? HOw do I get this working under 10.8.2 as it works flawlessly under OSX 10.6.8. For sure I didn't buy a new machine to have OSX 10.8.2 but I suspect this is the roadblock to installing my logic package.
    Help!

    Mark,
    Sorry...
    I completely lost the thread (I actually got confused between you and another poster on a another forum that was asking the same basic question) and somehow ended up thinking you were trying to install on a PPC Mac
    My apologies and please ingnore those parts of my last post relating to the PPC Macs...
    You have an Intel Mac and therefore Logic Studio 2 Boxed Upgrade set should install/run on your Mac without issue. As I said earlier.. you do not need to try and install from the original Logic Studio 1 /Logic 8 Boxed set...(It won't work anyhow because you have an Intel Mac and that version had a PPC installer)  but just install from the Logic Studio 2 / Logic Pro 9 Upgrade Boxed setof DVDs instead...
    Have you tried the "Make Disk Image" solution I gave earlier? That normnally works under such circumstances as what you are describing can happen when your DVD drive cannot read the DVDs correctly... I have had this situation myself where one drive read them okay and another failed to do so for whatever reason. Making and then installing from Disk images of those exact same disks resolved the issue for me...
    You can try to reinstall directly from the DVDs of course though under some circumstances it may not allow you to reinstall Logic Pro itself if that part of the original installation attempt was successful... in which case you can also try this... (It's probably the easiest method if Logic 9 was already installed and present in your Apps Folder)
    If the Logic Pro App is in your applications folder..
    Run Software Updates to update Logic Pro to a version that will run under 10.8.2 (The initially installed version of Logic will not)
    Run Logic
    Go to the menu bar in Logic and select Logic Pro/Install Additional Content and select all content in there..
    This content is basically exactly the same as what is stored on the remaining DVDs of the boxed set so you might not need to use the rest of the DVDs to install from but download it all instead from Apple Servers...

  • Probelm client auth from jsse client with open ssl server

    I tried to connect jsse client with a openssl server.. with clientAuth
    This is what i did ..
    Using openssl req comand i created a X509 certificate for server and imported the same to java keystore..
    The communication works fine without client authentication.
    To enable client auth i create client private/public key pair using keytool and exported the public key to a file client.public. and used it in open ssl server .
    This is how i invoke the client ..
    java
    -Djavax.net.debug=all
    -Djavax.net.ssl.trustStore=cacerts
    -Djavax.net.ssl.trustStorePassword=changeit
    -Djavax.net.private -Djavax.net.ssl.keyStorePassword=password EchoClient
    After which i get following error in server
    SSL3 alert write:fatal:handshake failure
    SSL_accept:error in SSLv3 read client certificate B
    SSL_accept:error in SSLv3 read client certificate B
    ERROR
    17246:error:140890C7:SSL routines:SSL3_GET_CLIENT_CERTIFICATE:peer did not return a certificate:s3_srvr.c:1666:
    shutting down SSL
    CONNECTION CLOSED
    The client debug says it is recieving a certificate request.. what could be the problem.. can anybody help...

    i also have that problem. I was trying to configure SSL in apache in Win XP machine, but this error occurs. Is there anyone, who can help on it?

  • Page With Flow Logic x Views

    Hi Guys,
    What is the main difference between working with Page with flow logic and Views? I mean, I may build up my site using only Page with flow logic or just using Views, so Why should I use views or Page w/FL or Both?
    Thank you in advance,
    Alexandre

    Hi ACR,
    You can build your application using only flow logic but not ONLY with views..
    Take a look at below threads for difference in MVC and Flow logic methods...
    [Difference in MVC and Flow logic 1.|Re: diffrence between MVC and Classical Bsp application]
    [Difference in MVC and Flow logic2.|Difference between MVC and PAGES WITH FLOW LOGIC]
    [Difference in MVC and Flow logic3.|MVC model / page with flow logic]
    Kindly search the forum for more details.
    Regards,
    Anubhav.

  • Sequence of Installs of RTA and SCA files for GRC AC 5.3

    Hello,
    I would like to confirm the correct sequence of applying RTA and SCA files for GRC AC 5.3.
    On ABAP Stack
    1- Install VirsaNH RTA on ECC 6.0 System with SAINT
    2- Install VirsaHR RTA on ECC 6.0 system which has SAP_HR
    3- Install both VirsaNH RTA and VIRSAHR RTA on a system which is SAP HR
    4- Install VIRSANH RTA on BI System. (There is no need of VirsaHR on BI system)
    5- Install all Support Packages up to 10 or 11 for VIRSANH & VIRSAHR with SPAM
    Next
    On JAVA Stack
    6- Install
    VIRCC00_0.sca
    VIRAE00_0.sca
    VIRRE00_0.sca
    VIRFF00_0.sca
    7- Install VIRACLP00_0.sca
    8- Then install VIRACCNTNT.SAR
    9- Next install EP RTA VIREPRTA00_0.sca
    10- Install all Java patches for the above components
    Based on the above,
    a- Plz confirm if the above sequence is right.
    b- My question is can I install 6, 7,8, 9 with JSPM at once as one step?
    c- Also can I install SCA files with JSPM first and then install RTA files on ABAP stack later?
    d- Also we have BI system with ABAP & JAVA Stacks. Is VIRSANH sufficient for both ABAP & JAVA, or do we need an additonal RTA for BI JAVA ?
    Thanks for your valuable inputs in advance.
    Regards,
    Haleem

    Hi,
    > 1- What is the UME of your BI Java stack ?
    >
    > Answer: We have installed BI JAVA, EP, EP Core, so we use SSO with EP and BI ABAP. So the portal is UME for BI Java stack.
    >
    Check below link which will answer your queries:
    Java RTA for GRC 5.3
    > 2- Check SAP Note 1174625 - Access Control 5.3 Java Support Pack Installation
    >
    > I checked the note 1174625, which says the following
    >
    > All of the sap.com/grc files have to be undeployed except the db and dictionary files for each component. The files that are NOT to be undeployed are:
    >
    > - sap.com/grc/ccxsysdb
    > - sap.com/grc/aedict
    > - sap.com/grc/redictionary
    > - sap.com/grc/ffdb
    >
    > Since this is a GRC AC 5.3 install on a fresh Netweaver 7.0 EHP1 Java stack install, do I need to undeploy all the above components, before doing AC 5.3 install, as mentioned in the note.
    >
    This is used when you do upgrade your old GRC release to latest one. So if you are doing fresh install then you need not to do these steps.
    > 3- Also this note 1174625 answers to most of my questions, but does not mention anything about VIRACCNTNT.SAR.  Is >this SAR file installed on JAVA Stack or ABAP stack? Is there a OSS note on VIRACCNTNT.SAR?
    >
    This file contains Roles, Rules, functions for RAR, CUP, ERM etc. in txt files which you need to upload when you will do the configuration of GRC.
    Thanks
    Sunny

  • N7k N2K and n5k N2K design questions

    Data Center with Dual N7K , want to add N2K for top of rack server access. I understand the model where I can set my servers up with a vPC Etherchannel to a pair of 2k with one 2k attached to each 7k. This model appears to meet all of the no single attached device rules of vPC. The question I have is how I can attach traditional server connectivity that doesn't support Etherchannel. In this model if I attach to a single 2k or team(without etherchannel) to both 2ks haven't I violated the no single attached device rule of vPC.
    I have a similar issue with the 2232 and N5k model. In order to support FCOE on a 2232, the only supported configuration is to attach the 2232 to a single 5k, in all of the design models I have seen the server is depicted with a vPC etherchannel to the two 2232s that are attached to their respective 5k. In this design if my server doesn't support an Etherchannel, and I am forced to utilize traditional teaming I have broken the no single attached device rule of VPC again.
    This no single attached device rule of vPC makes it really hard to utilize the FEX in either of these scenarios, What is the recommendation for connecting servers that don't support Etherchannel in these two models

    Hi,
    Take a look at the document Nexus 7000 Fex Supported/Not Supported Topologies and you'll see what options you currently have.
    As I mentioned, up to and including NX-OS 6.2, a single FEX can only be connected to a single Nexus 7000. This is what is shown as Figures 8, 9 and 10 in the unsupported topologies section.
    A server can be connected to two different FEX, and those two FEX could be connected to a single Nexus 7000 or two different Nexus 7000. The options are shown in Figures 6 and 7.
    Regards

Maybe you are looking for