Screen remains on after bringing it to my ear during a call (After ios 7 update)

Try these steps:
Screen will not lock or go black when answering calls
Verify mute or speaker have not been activated, just prior to placing your ear over the receiver.
While on a call hold your hand over the top third of the display, and verify that the screen is locked or goes to sleep.
Try turning iPhone off and then on again.
(from http://support.apple.com/kb/TS2802)
You might also want to try a reset:
Reset: Press and hold the Sleep/Wake button and the Home button together for at least ten seconds, until the Apple logo appears.

Similar Messages

Random reboots during phone calls after upgrading to OS4

My 3GS is rebooting without warning in the middle of calls after the upgrade - never did this before. This has happened at least five times today without any pattern: one 50-minute call was fine but other shorter ones have been cut off without warning. Battery is fine. It's been doing this ever since I upgraded last week.
Also I have noticed the whole phone has slowed down dramatically, presumably due to multitasking loading up the CPU?

Try doing a restore.
Also I have noticed the whole phone has slowed down dramatically, presumably due to multitasking loading up the CPU?
Yes.
Check out the new remodeled MacOSG website! 24-hour Apple-related news & support.
 MacOSG: An Apple User Group  iTunes: MacOSG Podcast  Follow us on Twitter: MacOSG

Unable to view contact photos during incoming calls after 7.1 upgrade.

This was working fine up until the phone was upgraded on my 5s
Has any one else had the same problem, and if so do you know of a fix?

Same thing has happened to my wifes phone, upgrading to 7.1 on her 5s.

New ipod nano 6th generation used 3 times. Screen remains black despite a full reset. Something special to do ?

Hi, I just bought a new ipod nano and used it 3 times. Today it did not work and I first believed that the battery was too low. I connected the device to the mac. Sync worked well and charge indicator as well. Nevertheless, the screen remained black. I therefore tried to reset the device and after the resetting, the screen remains as black as before. Any solution ? thanks and regards

If it does not get enough juice from the USB port, it will not charge.
You should NOT connect it to a USB hub. Connect it directly to the computer. If you use a desktop computer, use one of the ports on the back, not one on the front, which tend to be lower power.
You say you are using a macbook, which tend to be better about power. Make sure you don't have any settings that turn off power to the usb ports when the computer goes to sleep. Check your power settings in the settings screen.
i

My MacBook pro retina display 15 inch (2013) doesn't start. After I press the start button there is only a beep sound at regular interval. The screen remains blank and the keys don,t light up. Can anyone help please?

My MacBook pro retina display 15 inch (2013) doesn't start. After I press the start button there is only a beep sound at regular interval. The screen remains blank and the keys don,t light up. Can anyone help please?

If your MBP is under warranty, bring it to an Apple store and have the technicians fix it. If not, try the steps in this support article:
http://support.apple.com/kb/ts2570
Ciao.

Dark screen remains after waking from sleep mode

Whilst using Safari Version 3.1.2, Mac OS 10.4.11 on my Powerbook G4 (aluminum, 1.5 ghz), my screen remains dark upon waking from sleep mode. Trying to increase screen brightness is ineffectual for some reason likely related to this problem. My only workaround is to force shutdown and restart. Any ideas about a solution would be greatly appreciated.

Hi Gary,
This behavior is not a Safari issue but system related.
Close all applications an run in utilities> disc repair permissions.
After you done reboot an see what happens when your Mac gets to sleep mode again. This time don't open any applications to test it. Just leave it showing your desktop.
Post back with the results ...
Dimaxum

(1) Is there any way that I can get the transition menu to remain on the screen. I select a transition, drag it to the timeline and after I click done I have to start the process all over to perform this action on the next transition. I have premiere elem

(1) Is there any way that I can get the transition menu to remain on the screen. I select a transition, drag it to the timeline and after I click done I have to start the process all over to perform this action on the next transition. I have premiere elements 12. In older version the menu would stay on the screen.
(2) In pan and zoom how can start zoom on a photo in the original picture and zoom in and the next picture zoom out and the next photo pan from right to left and the next photo pan left to right.
Thanks
Sam

TidyCup
What computer operating system is your Premiere Elements 12 running on? If you have not already, be sure to update 12 to 12.1, using an opened project's Help Menu/Update.
But to the immediate questions, assuming Windows 7, 8, or 8.1 64 bit....
1. No, it is what it is. But, are you applying the same transition each time? If so, then highlight/select all the clips involved (all at one time), then Timeline Menu/Apply Default Transition will do just that for the highlighted/selected clips.
To highlight/select more than one clip at a time, hold down the Shift key of the computer main keyboard and then click on each clip that you want in the group selection
or
with your mouse cursor draw a rectangle around the clips that you want to select
2. Are you using the Premiere Elements 12/12.1 Expert workspace Pan and Zoom Tool? Or the pan or zoom presets under fx Effects/Presets/? With those you can do pan or zoom, not pan and zoom.
Or, are you in the Elements Organizer 12 Slideshow Editor using the pan and zoom effect there? Or, are you using keyframing the Motion Scale property for zoom and the Motion Position property for pan?
Are you asking about photos with landscape or portrait orientation?
The pan and zoom tool does one photo at a time.
Have you read the Adobe documentation on the Pan and Zoom Tool?
http://help.adobe.com/en_US/premiereelements/using/WSeffff8bffc802084-494411db12fd35452dd- 8000.html
Please review and clarify and then we can get into greater details on this.
Thanks.
ATR

TS3297 After downloading the latest version of iTunes, the store will not load. It appears as if it has loaded, but the screen remains blank.

After downloading the latest version of iTunes, the store will not load. It appears as if it has loaded, but the screen remains blank.

I have the same problem and have been fighting with it for several days. I think the last thing that I did before this happened was to let Quicktime update itself. When I open itunes and click on store, the connecting bar gets halfway and then stops. That leaves me with the white store page, if I leave it alone for a bit, I see words as in names of singers and but no pictures.
I have ran the diagnostics and see no problems at all, no event logs in windows, no errors at all. I've un-installed itunes and re-installed but no change. I'm using Norton 360 from comcast. I have windows 7 pro 64 bit. Also, the help in itunes doesn't display.
I put in a ticket with apple and the response I got back basically told me to do what I've already done. I created a new user and have the same issue.
Any help at all will be very much appreciated. I think this started August. 8, 2011.
thanks so much for reading

My 2008 15" macbook pro would not start up. After pushing the power button, the startup tone sounded, but kept repeating as if something was jammed. Screen remained black with no logo nor messages. Pls help.

My 2008 15" macbook pro would not start up. After pushing the power button, the startup tone sounded, but kept repeating as if something was jammed. Screen remained black with no logo nor messages. Pls help.

Now that you mentioned it, that might be the source of the problem. Something was definitely wrong with my graphics card before the incident happened. You mean that particular batch of graphics cards had some inherent issues, right? I went to the genius bar, and the 'genius' there, without trying to diagnose the problem properly, just adviced me to buy a new mbp! He said Apple will no longer try to fix or touch macs older than 5 yrs. Mine is 5.5 yrs old...

Screen remains black after power on

Brand new MacBook Pro 17" Unibody. I powered down last night and this morning on power up the screen remained blank (no visible faint displays). Keyboard backlight was on. Startup "noise" normal.
Battery was fully charged when shutdown.
Power cycled several times with no success. Removed all attachments including the power cord and after several attempts it finally powered on with a good screen display.
VERY frustrating experience. I have older 15" MBP and an iMAC and have never experienced this before.
Is there a patch/fix for this? Running 10.7.1 factory installed OS.
Is there some recourse to this? Should I take MBP to Genius desk? Can they investigate/eliminate the problem?
Jack

See Troubleshooting: My computer won't turn on
Post back if you still have troubles.

Screen remaining blurred after Alert dismissed [EDITED]

I've got something really quirky going on. Much of the time, when I use an alert, the screen remains blurred after the Alert has been dismissed. Has anyone run into this?
I had assumed that I could only close a TitleWindow after all the code I want executed was complete or the destruction of the popup would interfere. Testing doesn't seem to support that. So will something like this work without interfering with subsequent code? Will the event dispatch still take place regardless of timing issues? (disregard syntax errors below, just talking conceptual here).
protected function doSomething():void{
PopupManager.removePopup(this);
dispatchEvent(new Event("myEvent"));

I had this problem since months, and no one even was able to have any stab at it.
I updated the original post with more details.

Screen remaining blank after reopening lid (after 10.5.2 update)

Hello
after (successfully) updating from 10.5.1 to 10.5.2 several relevant problems appeared.
One is that closing the lid while the computer is on, and then reopening it later, the screen remains blank instead of coming to life. It is possible that the computer itself went to sleep and does not return, but the only way to get back is to press the on button for a few seconds to turn it off the hard way.
The other problem is described in a separated post. Any help is appreciated.
Thanks in advance,
Marinho.

me too, and I'm about to go nuts. There are tons of people having this issue, I fixed it temporarily by changing my hibernate mode (from 3 to 0) using terminal, everything worked great until the last update, now it's acting up again. Now, if I close my lid, and unplug something, or plug something, it gives me the startup sound (sounds like something moving) and won't come back if I open the lid.
There has got to be a solution. APPLE, FIX THIS. THIS IS RIDICULOUS.

Computer wakes from sleep but screen remains black even after restart

So, I installed SL yesterday and everything seemed fine. Last night, I closed my computer's monitor (putting it to sleep) for the night. This morning, when I opened it, the screen was black. I could not see anything, so I just restarted the computer.
On restart, the screen remained black.
After some experimentation, I realized that the computer was actually running, but I just couldn't see anything. So, I typed my password - screen was still black.
I then pressed the power button and enter - shutting down the computer properly.
After it shut down, I turned it on and the screen came on as normal...
What's going on here?
I checked some other threads and there was some potential issue with the iphoto screensaver, but I am not sure if that is the case here or not.
Any thoughts on how to fix this or prevent it form happening in the future?

I just had a similar thing occur. After resetting the pram the screen came back on.
I had noticed some problems with the hot corners for sleep mode earlier so I have deactivated them now to see if this was the problem. The only other thing I can think of is the recent Java update. I installed it right before the problem occurred.
Kurt

My macbook pro screen remains grey after latest firmware update

i just had the update notification for the latest firmware, proceeded to do so, and the screen remains grey, its been more than one hour and still grey, since its a firmware update i don't want to disturb it, but could it be that is taking so long?

Reboot it by pressing the power button down hard to force a shutdown.
If your still having problems, take it to Apple. I hope you have AppleCare becuase if they can't fix it, it's a new logicboard.

Whenever i start my macbook pro the screen remains gray with the apple symbol and the circle timer below. The screen stays this way even if i leave it for hours.

When i turn on my macbook a box appears telling me i need to restart my computer (in different languages) and in order to do so i have to press on the off button for a lil while. Even after doing this the same box appears and it never restarts correctly. This box appears every single time. I rarely turn my computer off. I just place it on sleep mode and restarts it only when i get prompted to. I brought it to genius and they couldnt figure out what the problem is so i was told it needed to be shipped to get fixed. I didnt have anything backed up. All i want saved are the pictures because i went to 2 events where i was the assigned photographer and i didnt get to save it to an external memory. Genius said that when shipped i cant give instructions like make sure to save the pictures and if they are unable to, call me if they should go on with the process. I was wishful thinking that to fix the problem they might not even have to touch the pictures memory part. I brought my MBP back home hoping it will miraculously starts and id be able to back it up but now all it does when i turn it on is the screen remains gray with the apple symbol and the circle timer below. The screen stays this way even if i leave it on for hours. Please help me fix this!!! cant i really specify to the technicians at apple to please make sure not to erase the pictures? Is there no other way to turn on my mac? I only need it to work ones.

There is no limit to the number of times you can re-install Office on the same computer.
You can activate by telephone:
The last paragraph is the relevant bit

Screen remains on after bringing it to my ear during a call (After ios 7 update)

Similar Messages

Maybe you are looking for