SCSI GPIB on Sun system driver issue

I am running SunOS 5.9 on a Sun Blade 150 with a NI SCSI GPIB Controller (it is the external box style).
Often when I run "init 6" the device driver banner does not appear during bootup.
(The driver installed on the system is NI-488.2 GPIB Device Driver, Version 2.3.)
When this occurs the solution is usually to cycle the power on the GPIB controller box and run "init 6" again.
Do you know what causes the driver to sometimes not load during bootup?
If I can't prevent this problem from happening, than maybe I can find a quicker way to resolve it when it does happen...
Is there an ibic command you recommend (maybe ResetSys) that can reload the GPIB driver without rebooting the workstation?
Is there any way via software to cycle the GPIB power?
Let me know if you need more information.
Thanks,
Scott

Hi,
This is a duplicate post for more information please follow this link.
Regards
Krista S.
Applications Engineering
National Instruments

Similar Messages

System Crashes repeatedly - hard drive issue?

I've been using my G4 933MHz with 2 internal hard drives for quite some time. I started having issues with the system crashing, while the system drive made a binding or poer up/down sound repeatedly. The drives were stacked on top of one another, so I bought a new cable and separated the 2 drives so they are now side by side. I thought maybe it was happening because they were getting too hot or something. The system worked for a few weeks, but is now back to having the same problem.
I've run both the Apple Disk utility and Tech Tool Pro and neither really come up with any problems. The Apple disk utility used to have issues seeing the drives right after a crash. Now it either sees them and says no fix needed or it doesnt see either drive at all.
Tech Tool Pro used to see both drives and all tests ran successfully. Now, I pretty much get a hardware nor supprted message each time I run it. At first I thought my system drive was the problem, but now I'm not sure. The fact that neither drive shows up in the disk utility makes me wonder if there is not some bigger problem. Both drives work perfectly fine sometimes. If I boot up a few times, they eventually show up and everything works fine for about 10-15 minutes, but eventually it crashes again.
Has anyone encountered this problem before? Or have insight into what might be wrong and how I could fix it? Or are there any other tests I can run, besides the normal hard drive tests? I'd just hate to go spend the money on a new hard drive to find out that my drives are fine and it's the system itself that is the problem. Any help is greatly appreciated.
By the way, the second drive is almost identical to the drive that came with the computer. I bought it from a mac dealer and it is the same brand.
Thanks,
Wil

They're both on the same ide cable. It's been setup this way for quite some time. One drive is setup as a master, the other as a slave. Never had any problems for the past couple of years. Issue just started about a month ago. Don't recall anything that may have triggered it. Just one night when I was sitting there, the whole thing froze. Ever since then, it has been freezing sporatically. Now it's doing it about every 2 minutes from when I get it booted up...if I can even get it to boot. Most of the time it just sits on a grey screen, then goes to the blinking folder with the system face and question mark, then after about 20 seconds of that, it eventually boots into the system drive and freezes or boots to the cd. It's completely random from what I can tell, as to which happens.

MySQL Driver issue

Hi,
I've been trying to connect to a MySQL database from Java. I have no problems from PHP so the db is fine, but suspect this is a driver issue.
I was using the Netbeans IDE but have now switched to a basic texteditor and command line to try understanding whats going on:
$ javac *.java -cp <other-libs-here>:~/Java/libs/mysql-connector-java-5.1.6-bin/mysql-connector-java-5.1.6-bin.jar
$ java Main
Failed to get connection
java.lang.ClassNotFoundException: com.mysql.jdbc.Driver
     at java.net.URLClassLoader$1.run(URLClassLoader.java:200)
     at java.security.AccessController.doPrivileged(Native Method)
     at java.net.URLClassLoader.findClass(URLClassLoader.java:188)
     at java.lang.ClassLoader.loadClass(ClassLoader.java:306)
     at sun.misc.Launcher$AppClassLoader.loadClass(Launcher.java:276)
     at java.lang.ClassLoader.loadClass(ClassLoader.java:251)
     at java.lang.ClassLoader.loadClassInternal(ClassLoader.java:319)
     at java.lang.Class.forName0(Native Method)
     at java.lang.Class.forName(Class.java:169)
     at MyDBConnection.init(MyDBConnection.java:38)
     at MyDBConnection.query(MyDBConnection.java:23)
     at Processor.index(Processor.java:31)
     at Main.main(Main.java:32)
Exception in thread "main" java.lang.NullPointerException
     at MyDBConnection.query(MyDBConnection.java:25)
     at Processor.index(Processor.java:31)
     at Main.main(Main.java:32)Any help you can offer on this would be greatly appreciated.

OK I thought one classpath was the same as another. It seems that the system classpath is something different.
Running: CLASSPATH=~/Java/libs/mysql-connector-java-5.1.6-bin/mysql-connector-java-5.1.6-bin.jar;export CLASSPATHin bash fixed this problems.
But I really want to get it working in NetBeans, does anyone have any ideas?

How to install Creative Cloud on any drive other than my System drive...

You are now chatting with 'Bhagawan'
Bhagawan: Hello. Welcome to Adobe Technical Support.
Bhagawan: Hi Steve
Steve: It appears CC installs on my system drive without asking me. The way I manage my system - this is not acceptable. So, how do I install on the drive I install all my other apps?
Bhagawan: I understand that you want to install Creative Cloud desktop app. Am I correct?
Steve: On a particular drive - not my system drive.
Steve: CC, Photoshop, etc.
Bhagawan: I will be glad to check and help you with this issue.
Bhagawan: Steve, creative cloud desktop app can be install only on C drive, but other apps you select for other drive.
Steve: My C: drive is dedicated to my OS only.
Steve: It is a special drive that will not work for very long if software companies put their programs on it till it fills up and then everything stops.
Steve: Didn't Adobe think of this?
Steve: I have one computer that only has a few MBs left of C:. What do I do on that computer?
Steve: "left on C:"
Bhagawan: Give me a minute.
Bhagawan: Thank you.
Bhagawan: Steve, I'm really sorry, creative cloud desktop app will be installed on C Drive, since the operating system is installed, but other Creative Cloud apps can be installed other Drive and depends on file size.

I had the same problem and finally solved it.
It is "funny" that CC doesn't ask you where to install apps. Or better to say, it asks you but doesn't care. In Creative Cloud desktop app/Preferences there is option to choose where you want apps to be installed, but they are still installed in C:/Program Files/....
How to install apps on secondary drive in just 3 steps:
1. Go to page Adobe CC 2014 Direct Download Links – Creative Cloud 2014 Release | ProDesignTools and download all apps that you will need.
2. Once downloaded, install it. During installation you will be asked where you want app to be installed (just like in any other "normal" installation)
3. Be happy
Hope I helped
Marko

Hard drive issues after update 10.10.3

Question also posted here:Hard Drive Issues (Both new and old)
I'm trapped in a HDD nightmare with my MacBook Pro mid-2012.
I updated to Yosemite 10.10.3 (with the Photos app). A couple of days after the update, I was watching a movie on my TV screen via HDMI. In the middle of the movie I removed the HDMI cable from the MacBook Pro and everything freezes. I forced shut down (Note: My HDD was encrypted). After I forced shut down, I tried to turn on and the loading screen would never stop loading - like, 14 hours stuck with the progress bar. Since I have backups, I decided to access DU and format my HDD. I tried everything. For real. Every command line I could type on Terminal to format, repair, erase and/or partition. I read almost every issue-related questions on the forums and stack exchange groups for a week (even posted my issue here: http://apple.stackexchange.com/questions/181090/erasing-and-partitioning-hard-dr ive-from-internet-recovery?noredirect=1#comment215695_181090).
So, I decided that it was a HDD failure and bought a new one.
I bought the Seagate 1TB SSHD Hybrid - ST1000LM014. Installed the new fresh disk and guess what? All those same problems again. I´m not able to restore from Time Machine because it doesn't recognize the disk in the restore page. But the disk is recognized in the DU. When I try to erase or partition the new SSHD, the same old errors: File system formatter failed. Yes, I tired GUID Partition Table, all of the security options, etc.
Please. Any light that you can throw at this issue, I'll be very grateful for. BTW, the new SSHD is recognized and the SMART Status says: Verified.
Any ideas on *** is going on?
Thanks in advance!
MacBook Pro (13-inch Mid 2012), i7, 8GB RAM

After I erase the hard drive (I assume one pass of writing zeros is good enough, 7 passes not needed?) do I turn off the laptop, then turn on and insert the Install Disk? Will there be a prompt telling me when to put in the disk? Or do I put in the disc right after erasing?
One pass is fine. If you've previously backed up your hard drive to an external hard drive using SuperDuper!, which is what I use and recommend, or another program, if it created a bootable drive, you want to boot off of it, bring up SuperDuper! and copy the drive back to the internal hard drive. SuperDuper also makes the drive bootable. When done, reboot, and you should be all set. If you're using Time Machine, you'll want to install the operating system, then restore the Time Machine backup. SuperDuper! is available from http://www.shirt-pocket.com/superduper/superduperdescription.html
Finally- should I update the OS? Is there a problem with the newest update that caused this crash, or was it just a spurious glitch/bad luck?
I've been running 10.5.8 for awhile with no issues, and would recommend moving to it.

TrueCrypt 6.2 system drive encryption hangs system sometimes a day

Hi,
I use truecrypt for years with xp and vista - last with Vista and T500, a few weeks ago I installed windows 7 x64 rtm. Every thing works fine and so I checked step by step my usual installed apps and tools.
I see win7 is not supported by truecrypt but seems to work fine. But sometimes (one or two a hour) my system hangs for about 10 to 40 seconds. So I decided to go step by step backwards and removed installed tools.
Removing TC solved my problem. Has anybody seen the same (TC6.2 on Win7 ult. x64 using Lenovo T500 with Intel SSD)?
best regards
Ronny

I have exactly the same problem, but with a HP Elitebook 2530p
TrueCrypt 7.0a
Windows 7 x64
SSD drive, but had the same problem on my traditional HDD.
The interval is somewhat longer for me, maybe a few times a day.
And, just as you discovered, removing truecrypt system encryption resolves the issue. Wonder if it's an issue with just the system drive encryption thingy, or it affects all systems having encrypted volumes opened?

Pixma ip6000d windows 7 driver issue. How do you get one?

Has anyone solved the windows 7 driver issue? The canon website does not have one yet is reported windows 7 capatable.

Hello ricksterofmi,
The PIXMA iP6000D Drivers are included with the Windows 7 Operating System through Windows Update. Please connect the PIXMA iP6000D to your computer and automatically install the drivers. Once this has been done, visit our website by selecting this LINK to download and install the Add On Module for full compatibility.
I hope this helps.
Did this answer your question? Please click the Accept as Solution button so that others may find the answer as well.

HP 6600 Scan\Print Driver Issue for Windows 7 Professional 64 bit

Hello,
For some time now I have been unable to scan or print from my desktop (Windows 7 Professional 64bit) and I have exhausted too much effort and am now bringing it to the masses.
The problem:
Printing: Currently receiving an "Error - Offline" message in my printer queue at all times.
Scanning: Scanning has never fully worked on this desktop. I am always unable to communicate with the printer. (Though webscan works through accessing the printers IP address)
Things I have tried:
Ran HPPSDr, followed directions (Unpluged power to printer, turn back on, restart computer) brings me to this website after it cannot fix. (Note that while the HPPSDr is running it always notions that there is a driver problem)
Uninstalled Drivers from CD-ROM, re-installed, countless times
Installed "Windows 7 Pro 64 bit drivers" from the HP website and uninstalled, countless times.
Attempted to set a static IP and use "Update IP Address" to point specifically at the printers IP.
Installed Drivers and finding the printer myself through it's own static IP address.
Turned off firewall and attempted to print (after reboot), same errors
Setting up the printer on all of my laptops (3) wirelessly to attempt to find if there is a problem with the printer or static IP. (1 is Windows VISTA 32bit and the other 2 are Ubuntu 32bit). All laptops are able to use the printer wirelessly without any problems.
Read all of the forums about this issue and attempted all of the 'solutions'. Although I mostly don't see that anyone with this same problem is resolved, unless I'm missing the perfect post.
Things I have not tried:
Plugging the USB directly into the desktop. (This seems self defeating as the purpose for this printer was to be able to print wirelessly to it from across the room)
Re-installed Windows 7 Pro 64bit (Trying to avoid this, would rather just print from laptops)
You tell me
Curiosities:
I have noticed strange things that make me believe the driver is somehow incomptable with my OS. Here is a shot of the properties of the printer:
Weird that it is not recognizing the model number.
Also in the Printer Settings when I go to the port tab, there is no port selected, if I try and tab away it forces me to select a port, yet when I do and 'apply' and then re-open the Printer Settings in the ports tab; it has again unselected the previously selected port.
Theories:
I feel like my OS is just refusing to notice the IP address for the wireless printer, no matter what I have it set to, even if it's dynamic. It's like the driver for Windows 7 Pro 64bit is actually not the correct driver for my system.
Anyways, another thing to mention is that I am not currently willing to wipe my operating system and re-install Windows 7 Pro in order to resolve this just yet. I want to see if anyone else has any other avenues I can try before even beginning to consider that.
Anyways, thanks in advance for taking the time to read my ramblings and hopefully someone who has resolved this issue can help me.

Hi Zerosouls,
I understand you are having an issue with HP 6600 Scan\Print Driver Issue for Windows 7 Professional 64 bit.
First try to click the Windows icon, type services in the Search box, and then click or tap View Local Services. Scroll down to the Windows Installer. Startup type should be - Automatic, and Service Status should be - started
Restart the computer after this step and try installing Hp Officejet 6600 again.
Please let me know what happens
Thanks
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos, Thumbs Up" on the bottom to say “Thanks” for helping!

Driver issue with Cisco HD Precision / JFV 4.4

Hi,
Just to installed Jabber for Video4.4 on my laptop ( win7 64bits)
all works fine except the video!! i use a Cisco HD precision wih Jabber, may be a driver issue, the camera is not recognized.
When i selected my integreted camera from laptop, the video is going up.
i've already the same issue with Jabber Video 4.3.
Does anyone has got the same issue? Any idea?
Thanks

Thread back from the dead...
I have this exact scenario playing out today trying to use a PrecisionHD USB camera with Windows 7. Completed the 1.5 update listed here and following the update I see the results in the picture. The LibUSB device is present, and it looks like a Tandberg HD camera is known to the system, but not accessible/usable.
Anybody have success with this issue or have any additional ideas to try?

HP PSC 1510 driver issue with Windows 8.1

I can't get my HP PSC 1510 all in one to work with Window's 8.1. I've installed HP doctor and the driver fails. I've downloaded the new driver so I don't know what the issue is? Anybody solve a similar issue?

Hi @DerekRL , and welcome to the HP Forums!
I can see you're experiencing driver issues. I'd like to help!
I would suggest Uninstalling the Printer Software.
Once it is uninstalled, I would suggest putting your system into clean boot mode within the Microsoft configuration. You can do so by following this document: How to perform a clean boot in Windows.
Once the computer is in clean boot mode, I would suggest reinstalling the HP Printer Install Wizard for Windows.
Good luck and please let me know the results of your troubleshooting steps. Thank you for posting on the HP Forums!
Please click “Accept as Solution " if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos, Thumbs Up" on the right to say “Thanks" for helping!
Jamieson
I work on behalf of HP
"Remember, I'm pulling for you, we're all in this together!" - Red Green.

Windows 8.1 not working properly, may be due to graphics driver issue

i have installed windows 8.1, but when i press widows key... the menu which opens is laging.... is it normal or some graphics driver issue... help required

Hi
It depands on the type of system/notebook you have installed windows 8.1 on
Please give us the Product # and the modle name of the notebook so that we can answer the question better and also try to find the right drivers if any.
Hope this helps.
***** Click the KUDOS Thumbs UP (Like) on the left to say 'Thanks'*****
****Make it easier for other people to find solutions, by marking my answer “Accept as Solution”&"Kudos"if it solves your problem.****
-VJ
Although I am an HP Employee, I am speaking for myself and not for HP.

On Windows 7 Ultimate, desktop with C (system) drive, D K and L drives, can I install Adope Creative Suite 6 Production Premium (from cd's) to Drive D (not C). Thank you.

On Windows 7 Ultimate, desktop with C (system) drive, D K and L drives, can I install Adope Creative Suite 6 Production Premium (from cd's) to Drive D (not C). Thank you.

you can but there may be some issues and a lot of files will be saved to your c drive, anyway.

Toshiba Satellite a505-6005 hard drive issue and questions regarding options I may have

Issue: start up computer and windows does not start. It eventually goes to a startup repair screen and eventually says "resolving disk errors...", and that's if it even gets to that screen. Unfortunately I never made a recovery disk or system image discs (I know that was not smart). I did however kept my files backed up so that was good.
Steps I took: Took it to Best Buy and the tech advised me that the Black Tie 2 year protection had expired on Jan 30th 2012, and so it could not be repaired for free. I asked the tech there how much it would cost to fix and they had advised me that it was most likely a hard drive issue and that it would cost nearly $400 to replace/fix it. So I decided to buy a new Asus K53E-BBR14 laptop since it was not much more. When I got home and loaded everything up and got the computer to how I want, I went ahead and made a recovery disc and system image disc's. I tried using the recovery disc that I had made with my Asus in the Toshiba laptop and boot it from the dvd drive and it did not get anywhere. So I ASSUME that it really is a hard drive error because the RAM worked just fine in my new laptop and "repairing disk errors.." means something is wrong with the hard drive:
Now that you know the background of what has happened my questions are as followed:
1. Can I buy a new hard drive for the Toshiba and use the recovery and system image disc's i created on the new hard drive that i install in the toshiba? and just removed the bloatware from Asus (or does that not even get added to the disc's I created)?
2. If so, will it prompt me to enter the Windows 7 product key? and therefore using the product key located on the bottom of the toshiba?
3. What other steps could I take to make this toshiba laptop salvageable? This way i can turn around and sell it.
Thanks,
Russell States

Also,
I noticed that i can purchase (well pay the shipping anyways) recovery media from Toshiba. Can I use that on a new hard drive installed in the toshiba?
BTW ran the Windows Memory Diagnostics Tool and no problems were found with the memory. and i do not care about the old hard drive as I have MY files backed up. I just want to try to get this toshiba laptop back to being "like new".
Thanks,
Russell

Incredibly slow MacBook, Internal Hard Drive issues...

Good morning everybody! I'm apologize if this post is extremely wordy...
I am extremely baffled by a particular issue with a MacBook 2.0GHz C2D which belongs to a friend of mine. The warranty is expired.
_Brief history:_
Several months ago, this MacBook could not find a bootable volume. The drive would not mount when booting from an external FireWire hard drive. It would not mount when the MacBook was put in Target Disk Mode and connected to another Mac. When booting from an external USB hard drive or with my MacBook Pro connected to the MacBook via Target Disk Mode, the MacBook booted up quickly. I came to the conclusion that the internal hard drive must have failed and needed to be replaced. Ultimately, the data was not recoverable from this drive.
I then proceeded to swap out the defective Apple OEM Seagate hard drive with a known working Apple OEM Fujitsu hard drive. When booting from the Leopard Install DVD, the MacBook would boot incredibly slow, but would finally reach the Installer Language screen. When proceeding to install Leopard, the drive would take a very long time to have data written to it, and ultimately the install failed. I removed the new hard drive from the MacBook and placed it in an external USB enclosure, attached it to the MacBook and booted from the Leopard Install DVD. Leopard would install successfully. I removed the hard drive from the enclosure and reinstalled it the MacBook. When booting from the freshly installed OS, the MacBook would take a very long time to boot. The MacBook is extremely slow!!!
I checked the Activity Monitor to ensure CPU & System Memory Usage was not going crazy. All Processes where normal with adequate CPU & Memory headroom.
I took the MacBook apart thinking that the SATA Controller Cable might be loose. No, it was firmly in place. I reassembled the MacBook and booted it up again. Still incredibly slow!
Finally, after several reboot attempts, the MacBook would book up quickly and operation was perfect. I applied all updates and continued testing the MacBook with great success. Gave my friend his MacBook back and he was grateful.
_Now for the kicker..._
My friend brought me his MacBook a week ago complaining that the MacBook was operating extremely slow (much like when I was initially testing it before). I verified the MacBook was slow when I tried using it. I tried several reboots and then it would get stuck on the gray Apple with spinning gear.
I tried booting into Single User Mode, but it gets stuck on "Waiting for root device"
I put the MacBook in Target Disk Mode and connected it to my G5 2.0GHz Dual Core. The hard drive would mount quickly on the G5 and I used Disk Utility to create a Restore Image. The disk operation would perform normally and the image would be created successfully.
I then partitioned the MacBook's hard drive when connected to the G5, ejected and proceeded to attempt OS reinstall. No dice! The hard drive is not even detected by the Disk Utility on the Leopard Install DVD.
Finally after several reattempts, the hard drive is recognized, but is extremely slow when trying to reinstall...and again, ultimately install fails. Using Disk Utility from Leopard Install DVD, the hard drive fails to unmount when I try formatting.
I don't have Apple Hardware Test disc for the MacBook or Apple Service Diagnostics disc for this model. Running TechTool Pro shows hardware to be okay, disk controller onboard the Fujitsu drive is okay, but running SMART & Surface Scan takes a long, long time (which I'm certain will ultimately error out). Running Drive Genius takes a long, long time as well.
Conclusion:
I think the SATA Controller Cable is defective. I can't think of anything else that would cause disk errors or performance issues like this. Your input is truly appreciated!

Even though no one responded to my post, I thought I'd share the resolution with the entire Apple community. I hope this information will be helpful to some of you with MacBooks or MacBook Pros that may be running painfully slow or may be exhibiting hard drive issues because your machine won't recognize the boot drive or fails to properly boot on a perfectly healthy S.M.A.R.T. verified hard drive. It just might be the hard drive connector/cable. Here it goes...
I visited my local Apple Retail Store and asked a "Genius" at the Genius Bar about this issue and told him my thoughts about a possible failed hard drive connector/cable. First, he didn't even know what a hard drive connector was! Then, he arrogantly stated that he never heard of such a thing and that these cables never fail. Finally, he blatantly dispelled this as a possibility.
On the contrary with my experience, I have had many failed PATA controller cables that required replacement when supporting the desktop PC's at work. I have personally owned and supported many Apple manufactured laptops and desktops and have never encountered this issue on a Mac...until this MacBook!
So, after looking at the Service Manual for the MacBook, I went over to my local Apple Authorized Service Provider and purchased the Hard Drive Connector Apple Part #922-7579. I replaced the original cable, reassembled and proceeded to boot the MacBook with the Leopard DVD installer. The Fujitsu drive was immediately recognized and was able to be formatted and Leopard installed without incident. The MacBook boots off the internal hard drive as normal again and works nice and fast again.
Thank you all for your time!
:D

Permissions Issue, Colour Wheel, Hard Drive Issue??

Hi!
I have had issues with my mid 2009 MBP recently and I'm wondering what the best way to fix them would be.
First off, I have some major permissions issues with my accounts. I am using 3 different users regualrly on the same machine and needed to access files from the home folder so I changed them a long time ago, and am not sure how to fix that. I have repaired the permissions countless times in the disk utility and it seems like there's always loads more to do each time. When I varify the disk, it says its all okay.
Secondly, I have had the machine freeze on me several times while doing very little on it. This happened awhile ago, and thought that it was just the permisions thing and so I did that again, and it started working better, for awhile. It would go a few days or weeks before doing the same thing, sometimes not even getting past the apple logo on startup before freezing. This makes me think it may be a hard drive issue???????
This morning, I tried dozens of times to boot, with no success at all..... until about the 25th time when it miraculasly booted. I have run permissions repair a few more times and it seems to be working okay at the moment, but the problem seems to be happening more often over time.
To complicate matters, I am traveling at the moment and will not be home for several months. I purchased an external harddrive last night and was able to successfully back up my data.
Question 1: Is it the permissions that are causing these problems, or is it related to something else. The computer seems to work fine when its working, and then once in awhile, decides its not going to do anything.
Question 2: Would upgrading to Lion (currently running 10.6.8) fix the permissions issues or just carry them forward? I would like to consolidate the 3 users into one, if that would solve it. Does the migration utility preserve permissions or does it give you a brand new start?
Question 3: If neither solving the permissions or the OS upgrade would fix the problem and it does need a new harddrive, is it possible to buy one and install it myself? I do not have apple care left on this machine and am on a very tight budget. I am used to taking things apart and all that as part of my job and it seems simple enough. Where can you buy a replacement??
Hopefully someone out there will be able to help me out on this one.
Cheers!!!!
Brian

bgroot422 wrote:
First off, I have some major permissions issues with my accounts. I am using 3 different users regularly on the same machine and needed to access files from the home folder so I changed them a long time ago, and am not sure how to fix that. I have repaired the permissions countless times in the disk utility and it seems like there's always loads more to do each time. When I verify the disk, it says its all okay.
Disk Utility permissions are separate from User account permissions.
This link is how to fix them
https://discussions.apple.com/thread/2181549?start=0&tstart=0
Disk Utility will always show something to be needing repair, but that's ok
Apple supoort doc.
https://support.apple.com/kb/TS1448?locale=da_DK
Verify Disk is good, that's a good thing.
To complicate matters, I am traveling at the moment and will not be home for several months. I purchased an external hard drive last night and was able to successfully back up my data.
Your data is backed up, hopefully not with TimeMachine alone, but if you did, then get another drive and backup data manually to that as well. If the TM drive gets messed up, it's a pain to get your data off of it.
Question 1: Is it the permissions that are causing these problems, or is it related to something else. The computer seems to work fine when its working, and then once in awhile, decides its not going to do anything.
Well you could call Apple for replacement 10.6.x disks, and just reinstall 10.6 and bundled programs, but this can kick out kext files out of the /System/Library/Extensions folder installed by some third party software.
This method fixes OS X, but doesn't touch your files or most programs.
Nor will this method fix your Users accounts if the issue is in there.
A creation of a new user, then deletion of the others, return files from backup (set permissions) will fix User folder issues if the above user permissions fix doesn't work.
(Of course you could wipe the drive from the 10.6 disk, but you have to install all software again)
Would upgrading to Lion (currently running 10.6.8) fix the permissions issues or just carry them forward?
No, you don't want to install Lion, it won't fix those issues in User folders, not only that Lion has it's own issues and doesn't work with a lot of older software etc. No use clusterfscking a already bad situtation when it's seems it's only localized to the User accounts.
I would like to consolidate the 3 users into one, if that would solve it.
Yes that could very nicely and tidy up things in the process.
What you do is transfer all files to one regular powered storage hard drive.
(Don't use/disconnect the TimeMachine drive for this as it preserves the users seperated and you don't want all those users back restoring with Migration Assistant)
Create the New User on the machine as Admin, log into it and delete all the other Users, transfer all your files back from the regular storage drive, changing all the permissions to yourself before placing them into their respective folders as they will have three different permissions.
Notes:
If you have a extensive iTunes playlists on one User (say #1), then create the new user with that same name (will require some work, create User 4, delete Users 1-3, reboot, create User 1, delete User 4) then transfer your iTunes folder to Music of that User 1 (same name as before). This will preserve the pathnames of your song locations and your playlists will be preserved.
(before you ask, no you can't combine playlists)
Also if you have photo's in iPhoto Library, you have to right click on it and "show package contents" inside is a folder called Originals, copy them out and import into the iPhoto of the User #1.
Does the migration utility preserve permissions or does it give you a brand new start?
Yes it preserves user permissions, no it doesn't give you a brand new start. Only a fresh install, creation of new users and then just transferring of files does that.
Nothing about TimeMachine or Migration Assistant gives one a "fresh start", it's if hosed, so is your restore.
If you want that sort of pristine protection, you need to clone your ideal boot partition/drive using Carbon Copy Cloner (free/donationware) occasionally as a hold the option key bootable drive, then you can erase and reverse clone the pristine saved clone.
One can also update the clone on occasion, this way keeping the clone pristine.
I maintain 3 clones time dated, even have my boot drive partitioned 50/50 and auto-cloned, this way I have two boot partitions on the road and two externals at home.
I never use TimeMachine, it's not bootable (well it is on 10.7.2 only to restore though)

SCSI GPIB on Sun system driver issue

Similar Messages

Maybe you are looking for