Security Manager traceroute ASA 5520
How can I use Security Manager (3.2) to configure a ASA 5520 to show up in a traceroute, have found a doc on how to do this from the cmd line but would prefer to keep everything in CSM.
Mike
There used to be a similar bug in IDM.
The sensor itself does not declare an interface as promiscuous.
SO CSM has to intepret the configuration to determine if the interface is promiscuous.
On an Appliance an Interface is InLine only if it is configured as part of an InLine Interface Pair, or has InLine Vlan Pairs assigned.
So CSM makes the assumption that if it is not part of an InLine Interface Pair and does not have InLine Vlan Pairs created, but is active and being monitored by a virtual sensor then it must be Promiscuous.
And the above is True for Appliances.
What the CSM developers may not have realized is that this is NOT true for Modules.
For most modules like the AIP-SSMs, the sensor is configured to monitor the interface, but there is nothing in the module configuration itself that tells you whether it is inline or promiscuous.
That knowledge is only within the configuration of the ASA chassis itself.
CSM is simply incorrectly using the rules for Appliances against the SSMs.
This was corrected in IDM by always just marking the SSM port as "monitored" if I remember right and not trying to specify whether it is promiscuous or inline.
CSM would likely have to make the same change, and just then just tell the user they need to check ASA configuration to determine whether or not the ASA is configured to send packets to the SSM promiscuously or inline.
Marco
Similar Messages
-
AIP mode different in Cisco Security Manager versus ASA
Hello,
AIP module (6.1(2)E3) being managed via CSM (3.3.0) shows as Promiscuous under Summary/Mode in Interfaces view.
On the ASA (5510, 7.2(4) ), when directing traffic to the AIP module we specified Inline mode.
Why is the CSM reading Promisucous?
In case it is a factor, the this is a ASA active/passive HA pair, each with its own AIP module.
Thank you for your insight.
PatrickThere used to be a similar bug in IDM.
The sensor itself does not declare an interface as promiscuous.
SO CSM has to intepret the configuration to determine if the interface is promiscuous.
On an Appliance an Interface is InLine only if it is configured as part of an InLine Interface Pair, or has InLine Vlan Pairs assigned.
So CSM makes the assumption that if it is not part of an InLine Interface Pair and does not have InLine Vlan Pairs created, but is active and being monitored by a virtual sensor then it must be Promiscuous.
And the above is True for Appliances.
What the CSM developers may not have realized is that this is NOT true for Modules.
For most modules like the AIP-SSMs, the sensor is configured to monitor the interface, but there is nothing in the module configuration itself that tells you whether it is inline or promiscuous.
That knowledge is only within the configuration of the ASA chassis itself.
CSM is simply incorrectly using the rules for Appliances against the SSMs.
This was corrected in IDM by always just marking the SSM port as "monitored" if I remember right and not trying to specify whether it is promiscuous or inline.
CSM would likely have to make the same change, and just then just tell the user they need to check ASA configuration to determine whether or not the ASA is configured to send packets to the SSM promiscuously or inline.
Marco -
Connectivity Issue between ASA 5520 firewall and Cisco Call Manager
Recently i have installed ASA 5520 firewall, Below is the detail for my network
ASA 5520 inside ip: 10.12.10.2/24
Cisco Switch 3560 IP: 10.12.10.1/24 for Data and 10.12.110.2/24 for Voice
Cisco Call Manager 3825 IP: 10.12.110.2/24
The users and the IP phone are getting IP from the DHCP server which configured on cisco 3560 Switch.
the Default Gateway for Data user is 10.12.10.2/24 and
for the voice users is 10.12.110.2/24
now the problem is that the users is not able to ping 10.12.110.2 call manager. please if somebody can help in this regard. i will appreciate the prompt response against this issues.Actually i don't wana to insert new subnet and complicate the nework. i need a simple way to solve the problem. below is the details for the asa 5520 config.
ASA Version 8.2(1)
name x.x.x.x Mobily
interface GigabitEthernet0/0
nameif inside
security-level 99
ip address 10.12.10.2 255.255.255.0
interface GigabitEthernet0/1
nameif outside
security-level 0
ip address x.x.x.x 255.255.255.252
object-group service DM_INLINE_SERVICE_1
service-object tcp-udp
service-object ip
service-object icmp
service-object udp
service-object tcp eq ftp
service-object tcp eq www
service-object tcp eq https
service-object tcp eq ssh
service-object tcp eq telnet
access-list RA_VPN_splitTunnelAcl_1 standard permit Inside-Network 255.255.255.0
access-list RA_VPN_splitTunnelAcl standard permit Inside-Network 255.255.255.0
access-list inside_nat0_outbound extended permit ip Inside-Network 255.255.255.0 10.12.10.16 255.255.255.240
access-list inside_nat0_outbound extended permit object-group DM_INLINE_SERVICE_1 10.12.10.16 255.255.255.240 Inside-Network 255.255.255.0
access-list inside_nat0_outbound_1 extended permit ip Inside-Network 255.255.255.0 10.12.10.16 255.255.255.240
pager lines 24
logging enable
logging asdm informational
mtu inside 1500
mtu outside 1500
mtu mgmt 1500
ip local pool VPN-Pool 172.16.1.1-172.16.1.30 mask 255.255.255.0
ip local pool VPN-Users 10.12.10.21-10.12.10.30 mask 255.255.255.0
no failover
icmp unreachable rate-limit 1 burst-size 1
asdm image disk0:/asdm-641.bin
asdm history enable
arp timeout 14400
global (inside) 2 interface
global (outside) 1 interface
nat (inside) 0 access-list inside_nat0_outbound_1
nat (inside) 1 Inside-Network 255.255.255.0
route outside 0.0.0.0 0.0.0.0 Mobily 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-record DfltAccessPolicy
http server enable
http Mgmt-Network 255.255.255.0 mgmt
http Inside-Network 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec security-association lifetime seconds 28800
crypto ipsec security-association lifetime kilobytes 4608000
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set pfs
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map outside_map interface outside
crypto isakmp enable outside
crypto isakmp policy 10
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
crypto isakmp policy 30
authentication pre-share
encryption 3des
hash md5
group 2
lifetime 86400
telnet Inside-Network 255.255.255.0 inside
telnet timeout 5
ssh Inside-Network 255.255.255.255 inside
<--- More ---> ssh timeout 5
console timeout 0
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
group-policy RA_VPN internal
group-policy RA_VPN attributes
dns-server value 86.51.34.17 8.8.8.8
vpn-tunnel-protocol IPSec
split-tunnel-policy tunnelspecified
split-tunnel-network-list value RA_VPN_splitTunnelAcl
username admin password LPtK/u1LnvHTA2vO encrypted privilege 15
tunnel-group RA_VPN type remote-access
tunnel-group RA_VPN general-attributes
address-pool VPN-Users
default-group-policy RA_VPN
tunnel-group RA_VPN ipsec-attributes
pre-shared-key *
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect netbios
inspect rsh
inspect rtsp
inspect skinny
inspect esmtp
inspect sqlnet
inspect sunrpc
inspect tftp
inspect sip
inspect xdmcp
service-policy global_policy global
prompt hostname context
Cryptochecksum:e5a64fa92ae465cd7dabd01ce605307d
: end -
Patch: CSCun25809, AnyConnect Password Management Fails with SMS Passcode for ASA 5520
Patch: CSCun25809, AnyConnect Password Management Fails with SMS Passcode for ASA 5520
Will this patch be installed in a version which I can use on ASA5520, if I understand the documentation correct, this patch is only installed in versions which are running on -X models of the ASA. 9.2, 9.3Once the ASA has dynamic NAT enabled to an outside interface, routing between same security level will not work.
You need to add route exempt the inside interfaces to all private subnet. -
ASA 5585-X CX20 Prime Security Manager
Hi Everyone
I'm trying to add our two 5585-X + CX20 units to Cisco Prime Security Manager. The ASAs seem to add correctly but the CX20s appear "undefined" for software version and model. Clicking on "Device Configuration" I get the error "Message From Server: SyntaxError: Unexpected token <"
I've tried removing and re-adding the devices but the same thing happens. Any ideas?
Thanks
JamesTwo contexts are included with the base licensing on the 5585-X. Up to 250 can be licensed.
The SKU (Stock Keeping Unit = part number) for 10 licenses would be ASA-5500-SC10.
FYI. here are all the SKUs for 5585 context licenses (click to enlarge): -
VPN clients not able to ping Remote PCs & Servers : ASA 5520
VPN is connected successfully. But not able to ping any remote ip or fqdn from client pc. But able to ping ASA 5520 firewalls inside interface. Also some clients able to access, some clients not able to access. I new to these firewalls. I tried most of ways from internet, please any one can help asap.
Remote ip section : 192.168.1.0/24
VPN IP Pool : 192.168.5.0/24
Running Config :
ip address 192.168.1.2 255.255.255.0
interface GigabitEthernet0/2
shutdown
no nameif
no security-level
no ip address
interface GigabitEthernet0/3
shutdown
no nameif
no security-level
no ip address
interface Management0/0
shutdown
no nameif
no security-level
no ip address
management-only
passwd z40TgSyhcLKQc3n1 encrypted
boot system disk0:/asa722-k8.bin
ftp mode passive
clock timezone GST 4
dns domain-lookup outside
dns domain-lookup inside
dns server-group DefaultDNS
name-server 213.42.20.20
domain-name default.domain.invalid
access-list outtoin extended permit tcp any host 83.111.113.114 eq 3389
access-list outtoin extended permit tcp any host 83.111.113.113 eq https
access-list outtoin extended permit tcp any host 83.111.113.114 eq smtp
access-list outtoin extended permit tcp any host 83.111.113.114 eq https
access-list outtoin extended permit tcp any host 83.111.113.114 eq www
access-list outtoin extended permit tcp any host 83.111.113.115 eq https
access-list outtoin extended permit tcp any host 94.56.148.98 eq 3389
access-list outtoin extended permit tcp any host 83.111.113.117 eq ssh
access-list fualavpn_splitTunnelAcl standard permit 192.168.1.0 255.255.255.0
access-list outside_nat0_outbound extended permit ip 192.168.5.0 255.255.255.0
92.168.1.0 255.255.255.0
access-list inside_nat0_outbound extended permit ip 192.168.1.0 255.255.255.0 1
2.168.5.0 255.255.255.0
access-list inet_in extended permit icmp any any time-exceeded
access-list inet_in extended permit icmp any any unreachable
access-list inet_in extended permit icmp any any echo-reply
access-list inet_in extended permit icmp any any echo
pager lines 24
logging enable
logging asdm informational
logging from-address [email protected]
logging recipient-address [email protected] level errors
logging recipient-address [email protected] level emergencies
logging recipient-address [email protected] level errors
mtu outside 1500
mtu inside 1500
ip local pool fualapool 192.168.5.10-192.168.5.50 mask 255.255.255.0
ip local pool VPNPool 192.168.5.51-192.168.5.150 mask 255.255.255.0
no failover
icmp unreachable rate-limit 1 burst-size 1
asdm image disk0:/asdm-522.bin
no asdm history enable
arp timeout 14400
global (outside) 1 interface
nat (inside) 0 access-list inside_nat0_outbound outside
nat (inside) 1 192.168.1.0 255.255.255.0
static (inside,outside) 94.56.148.98 192.168.1.11 netmask 255.255.255.255
static (inside,outside) 83.111.113.114 192.168.1.111 netmask 255.255.255.255
access-group inet_in in interface outside
route outside 0.0.0.0 0.0.0.0 83.111.113.116 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout uauth 0:05:00 absolute
group-policy DfltGrpPolicy attributes
banner none
wins-server none
dns-server none
dhcp-network-scope none
vpn-access-hours none
vpn-simultaneous-logins 10
vpn-idle-timeout 30
vpn-session-timeout none
vpn-filter none
vpn-tunnel-protocol IPSec l2tp-ipsec webvpn
password-storage disable
ip-comp disable
re-xauth disable
group-lock none
pfs disable
ipsec-udp disable
ipsec-udp-port 10000
split-tunnel-policy tunnelall
split-tunnel-network-list none
default-domain none
split-dns none
intercept-dhcp 255.255.255.255 disable
secure-unit-authentication disable
user-authentication disable
user-authentication-idle-timeout 30
ip-phone-bypass disable
leap-bypass disable
nem disable
backup-servers keep-client-config
msie-proxy server none
msie-proxy method no-modify
msie-proxy except-list none
msie-proxy local-bypass disable
nac disable
nac-sq-period 300
nac-reval-period 36000
nac-default-acl none
address-pools none
client-firewall none
client-access-rule none
webvpn
functions url-entry
html-content-filter none
homepage none
keep-alive-ignore 4
http-comp gzip
filter none
url-list none
customization value DfltCustomization
port-forward none
port-forward-name value Application Access
sso-server none
deny-message value Login was successful, but because certain criteria have no
been met or due to some specific group policy, you do not have permission to u
e any of the VPN features. Contact your IT administrator for more information
svc none
svc keep-installer installed
svc keepalive none
svc rekey time none
svc rekey method none
svc dpd-interval client none
svc dpd-interval gateway none
svc compression deflate
group-policy fualavpn internal
group-policy fualavpn attributes
dns-server value 192.168.1.111 192.168.1.100
vpn-tunnel-protocol IPSec
split-tunnel-policy tunnelspecified
split-tunnel-network-list value fualavpn_splitTunnelAcl
username test password I7ZgrgChfw4FV2AW encrypted privilege 0
username Mohamed password Vqmmt8cR/.Qu7LhU encrypted privilege 0
username Moghazi password GMr7xgdqmGEQ2SVR encrypted privilege 0
username Moghazi attributes
password-storage enable
username fualauaq password E6CgvoOpTKphiM2U encrypted privilege 0
username fualauaq attributes
password-storage enable
username fuala password IFtijSYb7LAOV/IW encrypted privilege 15
username Basher password Djf15nXIJXmayfjY encrypted privilege 0
username Basher attributes
password-storage enable
username fualafac password VGC/7cKXW1A6eyXS encrypted privilege 0
username fualafac attributes
password-storage enable
username fualaab password ONTH8opuP4RKgRXD encrypted privilege 0
username fualaab attributes
password-storage enable
username fualaadh2 password mNEgLxzPBeF4SyDb encrypted privilege 0
username fualaadh2 attributes
password-storage enable
username fualaain2 password LSKk6slwsVn4pxqr encrypted privilege 0
username fualaain2 attributes
password-storage enable
username fualafj2 password lE4Wu7.5s7VXwCqv encrypted privilege 0
username fualafj2 attributes
password-storage enable
username fualakf2 password 38oMUuwKyShs4Iid encrypted privilege 0
username fualakf2 attributes
password-storage enable
username fualaklb password .3AMGUZ1NWU1zzIp encrypted privilege 0
username fualaklb attributes
password-storage enable
username fualastr password RDXSdBgMaJxNLnaH encrypted privilege 0
username fualastr attributes
password-storage enable
username fualauaq2 password HnjodvZocYhDKrED encrypted privilege 0
username fualauaq2 attributes
password-storage enable
username fualastore password wWDVHfUu9pdM9jGj encrypted privilege 0
username fualastore attributes
password-storage enable
username fualadhd password GK8k1MkMlIDluqF4 encrypted privilege 0
username fualadhd attributes
password-storage enable
username fualaabi password eYL0j16kscNhhci4 encrypted privilege 0
username fualaabi attributes
password-storage enable
username fualaadh password GTs/9BVCAU0TRUQE encrypted privilege 0
username fualaadh attributes
password-storage enable
username fualajuh password b9QGJ1GHhR88reM1 encrypted privilege 0
username fualajuh attributes
password-storage enable
username fualadah password JwVlqQNIellNgxnZ encrypted privilege 0
username fualadah attributes
password-storage enable
username fualarak password UE41e9hpvcMeChqx encrypted privilege 0
username fualarak attributes
password-storage enable
username fualasnk password ZwZ7fVglexrCWFUH encrypted privilege 0
username fualasnk attributes
password-storage enable
username rais password HrvvrIw5tEuam/M8 encrypted privilege 0
username rais attributes
password-storage enable
username fualafuj password yY2jRMPqmNGS.3zb encrypted privilege 0
username fualafuj attributes
password-storage enable
username fualamaz password U1YUfQzFYrsatEzC encrypted privilege 0
username fualamaz attributes
password-storage enable
username fualashj password gN4AXk/oGBTEkelQ encrypted privilege 0
username fualashj attributes
password-storage enable
username fualabdz password tg.pB7RXJx2CWKWi encrypted privilege 0
username fualabdz attributes
password-storage enable
username fualamam password uwLjc0cV7LENI17Y encrypted privilege 0
username fualamam attributes
password-storage enable
username fualaajm password u3yLk0Pz0U1n.Q0c encrypted privilege 0
username fualaajm attributes
password-storage enable
username fualagrm password mUt3A60gLJ8N5HVr encrypted privilege 0
username fualagrm attributes
password-storage enable
username fualakfn password ceTa6jmvnzOFNSgF encrypted privilege 0
username fualakfn attributes
password-storage enable
username Fualaain password Yyhr.dlc6/J7WvF0 encrypted privilege 0
username Fualaain attributes
password-storage enable
username fualaban password RCJKLGTrh7VM2EBW encrypted privilege 0
username John password D9xGV1o/ONPM9YNW encrypted privilege 15
username John attributes
password-storage disable
username wrkshopuaq password cFKpS5e6Whp0A7TZ encrypted privilege 0
username wrkshopuaq attributes
password-storage enable
username Talha password 3VoAABwXxVonLmWi encrypted privilege 0
username Houssam password Cj/uHUqsj36xUv/R encrypted privilege 0
username Faraj password w2qYfE3DkYvS/oPq encrypted privilege 0
username Faraj attributes
password-storage enable
username gowth password HQhALLeiQXuIzptCnTv1rA== nt-encrypted privilege 15
username Hameed password 0Kr0N1VRmLuWdoDE encrypted privilege 0
username Hameed attributes
password-storage enable
username Hassan password Uy4ASuiNyEd70LCw encrypted privilege 0
username cisco password IPVBkPI1GLlHurPD encrypted privilege 15
username Karim password 5iOtm58EKMyvruZA encrypted privilege 0
username Shakir password BESX2bAvlbqbDha/ encrypted privilege 0
username Riad password iB.miiOF7qMESlCL encrypted privilege 0
username Azeem password 0zAqiCG8dmLyRQ8f encrypted privilege 15
username Azeem attributes
password-storage disable
username Osama password xu66er.7duIVaP79 encrypted privilege 0
username Osama attributes
password-storage enable
username Mahmoud password bonjr0B19aOQSpud encrypted privilege 0
username alpha password x8WO0aiHL3pVFy2E encrypted privilege 15
username Wissam password SctmeK/qKVNLh/Vv encrypted privilege 0
username Wissam attributes
password-storage enable
username Nabil password m4fMvkTgVwK/O3Ms encrypted privilege 0
aaa authentication telnet console LOCAL
aaa authentication ssh console LOCAL
aaa authentication enable console LOCAL
http server enable
http 0.0.0.0 0.0.0.0 outside
http 192.168.1.4 255.255.255.255 inside
http 192.168.1.100 255.255.255.255 inside
http 192.168.1.111 255.255.255.255 inside
http 192.168.1.200 255.255.255.255 inside
http 83.111.113.117 255.255.255.255 outside
http 192.168.1.17 255.255.255.255 inside
http 192.168.1.16 255.255.255.255 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto dynamic-map outside_dyn_map 20 set pfs
crypto dynamic-map outside_dyn_map 20 set transform-set ESP-3DES-SHA
crypto map outside_map 65535 ipsec-isakmp dynamic outside_dyn_map
crypto map outside_map interface outside
crypto isakmp enable outside
crypto isakmp policy 10
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
tunnel-group fualavpn type ipsec-ra
tunnel-group fualavpn type ipsec-ra
tunnel-group fualavpn general-attributes
address-pool fualapool
address-pool VPNPool
default-group-policy fualavpn
tunnel-group fualavpn ipsec-attributes
pre-shared-key *
tunnel-group fualavpn ppp-attributes
authentication pap
authentication ms-chap-v2
authentication eap-proxy
telnet 0.0.0.0 0.0.0.0 outside
telnet 0.0.0.0 0.0.0.0 inside
telnet timeout 5
ssh 0.0.0.0 0.0.0.0 outside
ssh 192.168.1.0 255.255.255.0 inside
ssh timeout 5
console timeout 0
management-access inside
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns migrated_dns_map_1
parameters
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns migrated_dns_map_1
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect icmp
inspect icmp error
service-policy global_policy global
prompt hostname context
Cryptochecksum:38e41e83465d37f69542355df734db35
: endHi,
What about translating the traffic on the local ASA (Active unit) for traffic received from the VPN tunnel to the internal interface IP address? You can try something like nat (outside,inside) source dynamic obj-VpnRemoteTraffic interface destination static StandbyIP StandbyIP
Regards, -
ASA 5520 intervlan routing at low speed
I have ASA 5520 and SSM-10 module. During copy between vlans, connected to gigabit port of asa the speed is up to 6,5 Mbyte/sec. Network cards and trunked switch are gigabit. I've temporarily disabled SSM but it didn't help. Here is my config. Also I found out, that putting SSM into bypass mode solves the problem. But I don't send any traffic to IPS...
ASA Version 8.4(2)
hostname ***
domain-name ***
enable password *** encrypted
passwd *** encrypted
multicast-routing
names
dns-guard
interface GigabitEthernet0/0
nameif DMZ
security-level 50
ip address 10.2.5.1 255.255.255.0
interface GigabitEthernet0/1
nameif inside
security-level 100
no ip address
interface GigabitEthernet0/1.100
vlan 100
nameif Devices
security-level 100
ip address 10.2.0.1 255.255.255.0
interface GigabitEthernet0/1.101
vlan 101
nameif Common
security-level 100
ip address 10.2.1.1 255.255.255.0
interface GigabitEthernet0/1.102
vlan 102
nameif Design
security-level 100
ip address 10.2.2.1 255.255.255.0
interface GigabitEthernet0/1.103
vlan 103
nameif Ruhlamat
security-level 90
ip address 10.2.3.1 255.255.255.0
interface GigabitEthernet0/2
no nameif
security-level 100
no ip address
interface GigabitEthernet0/2.10
vlan 10
nameif HOLOGR
security-level 40
ip address 10.1.2.4 255.255.0.0
interface GigabitEthernet0/3
nameif outside
security-level 0
ip address ***
interface Management0/0
nameif management
security-level 100
ip address 172.16.1.1 255.255.255.0
management-only
boot system disk0:/asa842-k8.bin
no ftp mode passive
clock timezone EEST 2
clock summer-time EEDT recurring last Sun Mar 3:00 last Sun Oct 4:00
dns server-group DefaultDNS
domain-name ***
same-security-traffic permit inter-interface
same-security-traffic permit intra-interface
object network WWW
host 10.2.1.6
object network MAIL
host 10.2.5.5
object network TEST
host 10.2.1.85
object-group network DM_INLINE_NETWORK_1
network-object host 10.1.0.88
network-object host 10.1.6.1
network-object host 10.1.6.5
network-object host 10.1.0.57
network-object 10.2.0.0 255.255.255.0
network-object host 10.1.6.4
network-object host 10.1.1.57
object-group service DM_INLINE_TCP_1 tcp
port-object eq 2080
port-object eq pop3
port-object eq smtp
object-group network DM_INLINE_NETWORK_6
network-object host 10.1.4.42
network-object host 10.1.4.234
network-object host 10.1.4.175
network-object host 10.1.4.217
object-group protocol DM_INLINE_PROTOCOL_5
protocol-object udp
protocol-object tcp
object-group network DM_INLINE_NETWORK_3
network-object host 10.2.1.4
network-object host 10.2.1.5
network-object host 10.2.1.6
network-object host 10.2.1.14
network-object host 10.2.1.91
object-group network DM_INLINE_NETWORK_4
network-object host 10.2.1.4
network-object host 10.2.1.5
network-object host 10.2.1.6
object-group service DM_INLINE_TCP_2 tcp
port-object eq pop3
port-object eq smtp
object-group network DM_INLINE_NETWORK_5
network-object host 10.2.1.14
network-object host 10.2.1.39
network-object host 10.2.1.4
network-object host 10.2.1.5
network-object host 10.2.1.6
network-object host 10.2.1.85
network-object host 10.2.1.31
network-object host 10.2.1.32
network-object host 10.2.1.40
network-object host 10.2.1.55
network-object host 10.2.1.35
network-object host 10.2.1.3
network-object host 10.2.1.2
object-group service DM_INLINE_TCP_3 tcp
port-object eq pop3
port-object eq smtp
object-group network DM_INLINE_NETWORK_7
network-object host 10.2.1.4
network-object host 10.2.1.5
object-group network DM_INLINE_NETWORK_9
network-object host 10.2.1.4
network-object host 10.2.1.3
object-group network DM_INLINE_NETWORK_2
network-object host 10.1.1.101
network-object host 10.1.6.1
network-object host 10.1.6.4
network-object host 10.1.6.5
network-object host 10.1.0.57
network-object host 10.1.1.57
object-group network DM_INLINE_NETWORK_10
network-object host 10.2.1.4
network-object host 10.2.1.5
network-object host 10.2.1.3
network-object host 10.2.1.2
object-group service DM_INLINE_TCP_4 tcp
port-object eq pop3
port-object eq smtp
object-group network DM_INLINE_NETWORK_12
network-object host 10.2.0.11
network-object host 10.2.0.14
object-group service DM_INLINE_TCP_5 tcp
port-object eq pop3
port-object eq smtp
object-group network DM_INLINE_NETWORK_13
network-object host 10.2.1.4
network-object host 10.2.1.5
object-group network DM_INLINE_NETWORK_14
network-object host 8.8.4.4
network-object host 8.8.8.8
network-object host 10.1.1.1
object-group network DM_INLINE_NETWORK_15
network-object host 10.2.1.39
network-object host 10.2.1.57
object-group network DM_INLINE_NETWORK_16
network-object host 10.2.1.14
network-object host 10.2.1.6
access-list outside_access_in extended permit tcp any 10.2.5.0 255.255.255.0 eq smtp
access-list outside_access_in extended permit tcp host *** host 10.2.1.85 eq ***
access-list outside_access_in extended permit tcp host *** host 10.2.1.6 eq ***
access-list Common_access_in extended permit icmp any any
access-list Common_access_in extended permit ip host 10.2.1.76 host ***
access-list Common_access_in extended permit ip host 10.2.1.6 any log disable inactive
access-list Common_access_in extended permit tcp host 10.2.1.6 host *** eq ***
access-list Common_access_in extended permit ip object-group DM_INLINE_NETWORK_1 6 host 10.2.5.5
access-list Common_access_in extended permit ip object-group DM_INLINE_NETWORK_3 10.2.2.0 255.255.255.0
access-list Common_access_in extended permit udp object-group DM_INLINE_NETWORK_7 any eq ntp log disable
access-list Common_access_in extended permit object-group DM_INLINE_PROTOCOL_5 object-group DM_INLINE_NETWORK_13 object-group DM_INLINE_NETWORK_14 eq domain
access-list Common_access_in extended permit ip object-group DM_INLINE_NETWORK_5 host 10.2.3.3
access-list Common_access_in extended permit tcp object-group DM_INLINE_NETWORK_15 host 10.1.1.1 object-group DM_INLINE_TCP_3
access-list Common_access_in extended permit ip 10.2.1.0 255.255.255.0 object-group DM_INLINE_NETWORK_1
access-list Common_access_in extended permit tcp 10.2.1.0 255.255.255.0 host 10.2.5.5 object-group DM_INLINE_TCP_1
access-list Design_access_in extended permit tcp 10.2.2.0 255.255.255.0 host 10.2.5.5 object-group DM_INLINE_TCP_2
access-list Design_access_in extended permit ip 10.2.2.0 255.255.255.0 object-group DM_INLINE_NETWORK_4 log disable
access-list HOLOGR_access_in extended permit icmp any any log disable
access-list HOLOGR_access_in extended permit tcp host 10.1.1.1 host 10.2.5.5 object-group DM_INLINE_TCP_4
access-list HOLOGR_access_in extended permit ip object-group DM_INLINE_NETWORK_6 object-group DM_INLINE_NETWORK_9
access-list HOLOGR_access_in extended permit ip object-group DM_INLINE_NETWORK_2 10.2.1.0 255.255.255.0
access-list HOLOGR_access_in extended permit ip host 10.1.4.214 object-group DM_INLINE_NETWORK_12
access-list Ruhlamat_access_in extended permit ip host 10.2.3.3 object-group DM_INLINE_NETWORK_10
access-list Ruhlamat_access_in extended permit tcp host 10.2.3.3 host 10.2.5.5 object-group DM_INLINE_TCP_5
access-list test extended permit tcp any host 10.2.5.1 eq telnet
access-list test extended permit tcp any host 10.2.5.1 eq https
access-list test extended permit tcp host 10.2.5.1 any eq https
access-list test extended permit tcp host 10.2.5.1 any eq telnet
pager lines 24
logging enable
logging timestamp
logging buffer-size 8192
logging buffered critical
logging trap warnings
logging asdm informational
logging from-address ***
logging recipient-address *** level critical
logging host Common 10.2.1.2
logging flash-bufferwrap
logging flash-maximum-allocation 8192
logging permit-hostdown
no logging message 106014
no logging message 313005
no logging message 313001
no logging message 106023
no logging message 305006
no logging message 733101
no logging message 733100
no logging message 304001
logging message 313001 level critical
logging message 106023 level errors
mtu DMZ 1500
mtu inside 1500
mtu Devices 1500
mtu Common 1500
mtu Design 1500
mtu Ruhlamat 1500
mtu HOLOGR 1500
mtu outside 1500
mtu management 1500
no failover
icmp unreachable rate-limit 1 burst-size 1
icmp permit any DMZ
icmp permit any Common
icmp permit any HOLOGR
icmp permit any outside
asdm image disk0:/asdm-645-206.bin
asdm history enable
arp timeout 14400
object network WWW
nat (Common,outside) static interface service tcp *** ***
object network MAIL
nat (DMZ,outside) static interface service tcp smtp smtp
nat (DMZ,outside) after-auto source dynamic any interface
nat (Common,outside) after-auto source dynamic any interface
nat (Devices,outside) after-auto source dynamic any interface
access-group Common_access_in in interface Common
access-group Design_access_in in interface Design
access-group Ruhlamat_access_in in interface Ruhlamat
access-group HOLOGR_access_in in interface HOLOGR
access-group outside_access_in in interface outside
route outside 0.0.0.0 0.0.0.0 *** 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
no user-identity enable
user-identity default-domain LOCAL
http server enable
http 10.2.1.6 255.255.255.255 Common
snmp-server host Common 10.2.1.6 community *****
no snmp-server location
no snmp-server contact
snmp-server community *****
snmp-server enable traps snmp authentication linkup linkdown coldstart
sysopt noproxyarp DMZ
sysopt noproxyarp inside
sysopt noproxyarp Devices
sysopt noproxyarp Common
sysopt noproxyarp Design
sysopt noproxyarp Ruhlamat
sysopt noproxyarp HOLOGR
sysopt noproxyarp outside
sysopt noproxyarp management
service resetoutside
telnet 10.2.1.0 255.255.255.0 Common
telnet timeout 5
ssh timeout 5
console timeout 0
management-access Common
dhcprelay setroute Common
threat-detection basic-threat
threat-detection scanning-threat
no threat-detection statistics access-list
no threat-detection statistics tcp-intercept
ntp server 10.2.1.4 source Common prefer
webvpn
smtp-server 10.2.5.5
prompt hostname context
call-home reporting anonymous
call-home
profile CiscoTAC-1
no active
destination address http https://tools.cisco.com/its/service/oddce/services/DD
CEService
destination address email [email protected]
destination transport-method http
subscribe-to-alert-group diagnostic
subscribe-to-alert-group environment
subscribe-to-alert-group inventory periodic monthly
subscribe-to-alert-group configuration periodic monthly
subscribe-to-alert-group telemetry periodic daily
Cryptochecksum:ad02ecbd84a727e4a26699915feca3a5
: endHi Philip,
I don't see any features configured that would affect the throughput of the data transfer. Do you see any CRC errors or overruns increasing on the interfaces during the transfer? If not, I would suggest setting up captures on the ingress and egress interfaces of the ASA so you can understand exactly why the connection is slowing down and see if the ASA is inducing the delay:
https://supportforums.cisco.com/docs/DOC-1222
-Mike -
Cisco ASA 5520 Failover with DMZ
I have a pair of Cisco ASA 5520s running as a primary/standby. Everything is working properly with the primary ASA, however when I trigger a failover, everything works except for the DMZ interface on the standby ASA. I've poured over the configs, but perhaps I have been staring at them too long because I am just not seeing anything.
Below is the output of the sh run failover, sh failover, and sh run interface commands for each unit...
PRIMARY ASA
Primary-ASA# sh run failover
failover
failover lan unit primary
failover lan interface stateful1 GigabitEthernet0/3
failover key *****
failover link stateful1 GigabitEthernet0/3
failover interface ip stateful1 192.168.216.1 255.255.255.0 standby 192.168.216.2
Primary-ASA# sh failover
Failover On
Failover unit Primary
Failover LAN Interface: stateful1 GigabitEthernet0/3 (up)
Unit Poll frequency 1 seconds, holdtime 15 seconds
Interface Poll frequency 5 seconds, holdtime 25 seconds
Interface Policy 1
Monitored Interfaces 3 of 160 maximum
Version: Ours 8.2(5), Mate 8.2(5)
Last Failover at: 20:39:23 CDT Sep 3 2013
This host: Primary - Active
Active time: 69648 (sec)
slot 0: ASA5520 hw/sw rev (2.0/8.2(5)) status (Up Sys)
Interface outside (184.61.38.254): Normal
Interface inside (192.168.218.252): Normal
Interface dmz (192.168.215.254): Normal (Waiting)
Interface management (192.168.1.1): Normal (Not-Monitored)
slot 1: ASA-SSM-10 hw/sw rev (1.0/6.0(3)E1) status (Up/Up)
IPS, 6.0(3)E1, Up
Other host: Secondary - Standby Ready
Active time: 2119 (sec)
slot 0: ASA5520 hw/sw rev (2.0/8.2(5)) status (Up Sys)
Interface outside (184.61.38.253): Normal
Interface inside (192.168.218.253): Normal
Interface dmz (192.168.215.252): Normal (Waiting)
Interface management (192.168.1.2): Normal (Not-Monitored)
slot 1: ASA-SSM-10 hw/sw rev (1.0/6.0(3)E1) status (Up/Up)
IPS, 6.0(3)E1, Up
Primary-ASA# sh run interface
interface GigabitEthernet0/0
nameif outside
security-level 0
ip address 184.61.38.254 255.255.255.128 standby 184.61.38.253
ospf cost 10
interface GigabitEthernet0/1
nameif inside
security-level 100
ip address 192.168.218.252 255.255.255.0 standby 192.168.218.253
ospf cost 10
interface GigabitEthernet0/2
nameif dmz
security-level 50
ip address 192.168.215.254 255.255.255.0 standby 192.168.215.252
ospf cost 10
interface GigabitEthernet0/3
description LAN/STATE Failover Interface
interface Management0/0
nameif management
security-level 100
ip address 192.168.1.1 255.255.255.0 standby 192.168.1.2
ospf cost 10
management-only
STANDBY ASA
Standby-ASA# sh run failover
failover
failover lan unit secondary
failover lan interface stateful1 GigabitEthernet0/3
failover key *****
failover link stateful1 GigabitEthernet0/3
failover interface ip stateful1 192.168.216.1 255.255.255.0 standby 192.168.216.2
Standby-ASA# sh failover
Failover On
Failover unit Secondary
Failover LAN Interface: stateful1 GigabitEthernet0/3 (up)
Unit Poll frequency 1 seconds, holdtime 15 seconds
Interface Poll frequency 5 seconds, holdtime 25 seconds
Interface Policy 1
Monitored Interfaces 3 of 160 maximum
Version: Ours 8.2(5), Mate 8.2(5)
Last Failover at: 20:39:23 CDT Sep 3 2013
This host: Secondary - Standby Ready
Active time: 2119 (sec)
slot 0: ASA5520 hw/sw rev (2.0/8.2(5)) status (Up Sys)
Interface outside (184.61.38.253): Normal
Interface inside (192.168.218.253): Normal
Interface dmz (192.168.215.252): Normal (Waiting)
Interface management (192.168.1.2): Normal (Not-Monitored)
slot 1: ASA-SSM-10 hw/sw rev (1.0/6.0(3)E1) status (Up/Up)
IPS, 6.0(3)E1, Up
Other host: Primary - Active
Active time: 70110 (sec)
slot 0: ASA5520 hw/sw rev (2.0/8.2(5)) status (Up Sys)
Interface outside (184.61.38.254): Normal
Interface inside (192.168.218.252): Normal
Interface dmz (192.168.215.254): Normal (Waiting)
Interface management (192.168.1.1): Normal (Not-Monitored)
slot 1: ASA-SSM-10 hw/sw rev (1.0/6.0(3)E1) status (Up/Up)
IPS, 6.0(3)E1, Up
Standby-ASA# sh run interface
interface GigabitEthernet0/0
nameif outside
security-level 0
ip address 184.61.38.254 255.255.255.128 standby 184.61.38.253
ospf cost 10
interface GigabitEthernet0/1
nameif inside
security-level 100
ip address 192.168.218.252 255.255.255.0 standby 192.168.218.253
ospf cost 10
interface GigabitEthernet0/2
nameif dmz
security-level 50
ip address 192.168.215.254 255.255.255.0 standby 192.168.215.252
ospf cost 10
interface GigabitEthernet0/3
description LAN/STATE Failover Interface
interface Management0/0
nameif management
security-level 100
ip address 192.168.1.1 255.255.255.0 standby 192.168.1.2
ospf cost 10
management-only
Does anyone see something I might be missing? I am at a loss...I'll just answer my own question...the configs are correct, but it the interface on the standby ASA was plugged into an improperly configured switchport. That'll do it everytime.
-
Asa 5520 "loosing" code after code has been put in and operating
Sorry to ask this if it has all ready been covered. We have an asa 5520 running 8.3.2(1) code. Three times now I have entered code and rules in our asa and had things working, only to have the code "dissapear" and thus things stop working. We upgraded to 8.3.2(1) back in January of 2011, and have not had this problem until the last month. I was wondering if there is a bug with 8.3.2(1) code that has decided to show itself for whatever reason now. We have also had some other things relating to the VPN that were "working" and at some point just stopped working. We do have a second asa 5520 that is the failover/standby. We also have two 6509 with firewall services modules, one primary and the other standby. Just wondering how to troubleshoot something like this. I have putty logs of me putting the code in and doing a write mem saving the changes, yet on three occations those things stopped working, and I had to put the code in again.
**update** as I was typing this, we realised there was a problem with the two ASA's. For some reason, failover had stopped working, and both ASA's were trying to be the primary and causing issues. After several reboots, we wound up turning failover back on on the second ASA, and things seem to be normal now. No idea what would have caused the failover to break. Not sure how long this had been going on, it may have had to do with my code seeming to dissapear?Here is the output of the show ver. I removed the serial number.
ACH-2nd-EXT-ASA01#sh ver
Cisco Adaptive Security Appliance Software Version 8.3(2)1
Device Manager Version 6.4(7)
Compiled on Wed 04-Aug-10 21:41 by builders
System image file is "disk0:/asa832-1-k8.bin"
Config file at boot was "startup-config"
ACH-2nd-EXT-ASA01 up 4 days 22 hours
failover cluster up 4 days 22 hours
Hardware: ASA5520, 2048 MB RAM, CPU Pentium 4 Celeron 2000 MHz
Internal ATA Compact Flash, 256MB
BIOS Flash M50FW080 @ 0xfff00000, 1024KB
Encryption hardware device : Cisco ASA-55x0 on-board accelerator (revision 0x0)
Boot microcode : CN1000-MC-BOOT-2.00
SSL/IKE microcode: CNLite-MC-SSLm-PLUS-2.03
IPSec microcode : CNlite-MC-IPSECm-MAIN-2.06
0: Ext: GigabitEthernet0/0 : address is 001d.a298.c41c, irq 9
1: Ext: GigabitEthernet0/1 : address is 001d.a298.c41d, irq 9
2: Ext: GigabitEthernet0/2 : address is 001d.a298.c41e, irq 9
3: Ext: GigabitEthernet0/3 : address is 001d.a298.c41f, irq 9
4: Ext: Management0/0 : address is 001d.a298.c420, irq 11
5: Int: Internal-Data0/0 : address is 0000.0001.0002, irq 11
6: Int: Internal-Control0/0 : address is 0000.0001.0001, irq 5
Licensed features for this platform:
Maximum Physical Interfaces : Unlimited perpetual
Maximum VLANs : 150 perpetual
Inside Hosts : Unlimited perpetual
Failover : Active/Active perpetual
VPN-DES : Enabled perpetual
VPN-3DES-AES : Enabled perpetual
Security Contexts : 2 perpetual
GTP/GPRS : Disabled perpetual
SSL VPN Peers : 10 perpetual
Total VPN Peers : 750 perpetual
Shared License : Disabled perpetual
AnyConnect for Mobile : Enabled perpetual
AnyConnect for Cisco VPN Phone : Disabled perpetual
AnyConnect Essentials : Enabled perpetual
Advanced Endpoint Assessment : Disabled perpetual
UC Phone Proxy Sessions : 2 perpetual
Total UC Proxy Sessions : 2 perpetual
Botnet Traffic Filter : Disabled perpetual
Intercompany Media Engine : Disabled perpetual
This platform has an ASA 5520 VPN Plus license.
Failover cluster licensed features for this platform:
Maximum Physical Interfaces : Unlimited perpetual
Maximum VLANs : 150 perpetual
Inside Hosts : Unlimited perpetual
Failover : Active/Active perpetual
VPN-DES : Enabled perpetual
VPN-3DES-AES : Enabled perpetual
Security Contexts : 4 perpetual
GTP/GPRS : Disabled perpetual
SSL VPN Peers : 20 perpetual
Total VPN Peers : 750 perpetual
Shared License : Disabled perpetual
AnyConnect for Mobile : Enabled perpetual
AnyConnect for Cisco VPN Phone : Disabled perpetual
AnyConnect Essentials : Enabled perpetual
Advanced Endpoint Assessment : Disabled perpetual
UC Phone Proxy Sessions : 4 perpetual
Total UC Proxy Sessions : 4 perpetual
Botnet Traffic Filter : Disabled perpetual
Intercompany Media Engine : Disabled perpetual
This platform has an ASA 5520 VPN Plus license.
Serial Number: xxxxxxxxxxx
Running Permanent Activation Key: 0xf730cf7a 0x0449cabf 0xc922e5d4 0xc7bc5cb0 0x851ed6bb
Configuration register is 0x1
Configuration has not been modified since last system restart.
ACH-2nd-EXT-ASA01# -
Hi All,
we recently installed a activaiton key for the Anyconnect License on our ASA 5520. We have a pair runnning, in Active/Standby mode, on IOS 8.0. The Activation/License was installed on the Primary ASA. Once installed the all failover configuration was removed, and we were left with 2 ASAs running in Active/Active mode. This cause haoc across the network. I would like to go back and recover and reinstall the old activation key. Is this possible?? If so how would I be able to achieve this. Or do I need to ontain a new license key. Ultimately I would like to get back to the stage before instlaling the Anyconnect License, where we had a 2 ASAs running in Active/Standby mode.
Thank you for your help and suggestions.
Cheers
Deena
oput put from sh activation-key detail and sh version
CH-ASA# sh act det
Serial Number: JMX1101K2SU
Permanent Flash Activation Key: 0x370fc559 0x2476a024 0xccc355a4 0xacd81440 0x4110329d
Licensed features for this platform:
Maximum Physical Interfaces : Unlimited
Maximum VLANs : 150
Inside Hosts : Unlimited
Failover : Active/Active
VPN-DES : Enabled
VPN-3DES-AES : Enabled
Security Contexts : 2
GTP/GPRS : Disabled
VPN Peers : 750
WebVPN Peers : 2
AnyConnect for Mobile : Disabled
AnyConnect for Linksys phone : Disabled
Advanced Endpoint Assessment : Disabled
UC Proxy Sessions : 2
Temporary Flash Activation Key: 0x29249e66 0x500f33dc 0xcd79274e 0x534c7c93 0x81bc53bc
Licensed features for this platform:
Maximum Physical Interfaces : Unlimited
Maximum VLANs : 150
Inside Hosts : Unlimited
Failover : Active/Active
VPN-DES : Enabled
VPN-3DES-AES : Disabled
Security Contexts : 2
GTP/GPRS : Disabled
VPN Peers : 750
WebVPN Peers : 750
AnyConnect for Mobile : Disabled
AnyConnect for Linksys phone : Disabled
Advanced Endpoint Assessment : Disabled
UC Proxy Sessions : 2
This is a time-based license that will expire in 27 day(s).
Running Activation Key: 0x29249e66 0x500f33dc 0xcd79274e 0x534c7c93 0x81bc53bc
Licensed features for this platform:
Maximum Physical Interfaces : Unlimited
Maximum VLANs : 150
Inside Hosts : Unlimited
Failover : Active/Active
VPN-DES : Enabled
VPN-3DES-AES : Enabled
Security Contexts : 2
GTP/GPRS : Disabled
VPN Peers : 750
WebVPN Peers : 750
AnyConnect for Mobile : Disabled
AnyConnect for Linksys phone : Disabled
Advanced Endpoint Assessment : Disabled
UC Proxy Sessions : 2
This platform has an ASA 5520 VPN Plus license.
This is a time-based license that will expire in 27 day(s).
The flash activation key is the SAME as the running key.
CH-ASA# sh ver
Cisco Adaptive Security Appliance Software Version 8.0(5)
Device Manager Version 6.2(5)53
Compiled on Mon 02-Nov-09 21:22 by builders
System image file is "disk0:/asa805-k8.bin"
Config file at boot was "startup-config"
CH-ASA up 18 hours 30 mins
Hardware: ASA5520-K8, 2048 MB RAM, CPU Pentium 4 Celeron 2000 MHz
Internal ATA Compact Flash, 256MB
BIOS Flash AT49LW080 @ 0xffe00000, 1024KB
Encryption hardware device : Cisco ASA-55x0 on-board accelerator (revision 0x0)
Boot microcode : CN1000-MC-BOOT-2.00
SSL/IKE microcode: CNLite-MC-SSLm-PLUS-2.03
IPSec microcode : CNlite-MC-IPSECm-MAIN-2.05
0: Ext: GigabitEthernet0/0 : address is 0019.0665.6dfc, irq 9
1: Ext: GigabitEthernet0/1 : address is 0019.0665.6dfd, irq 9
2: Ext: GigabitEthernet0/2 : address is 0019.0665.6dfe, irq 9
3: Ext: GigabitEthernet0/3 : address is 0019.0665.6dff, irq 9
4: Ext: Management0/0 : address is 0019.0665.6dfb, irq 11
5: Int: Internal-Data0/0 : address is 0000.0001.0002, irq 11
6: Int: Internal-Control0/0 : address is 0000.0001.0001, irq 5
Licensed features for this platform:
Maximum Physical Interfaces : Unlimited
Maximum VLANs : 150
Inside Hosts : Unlimited
Failover : Active/Active
VPN-DES : Enabled
VPN-3DES-AES : Enabled
Security Contexts : 2
GTP/GPRS : Disabled
VPN Peers : 750
WebVPN Peers : 750
AnyConnect for Mobile : Disabled
AnyConnect for Linksys phone : Disabled
Advanced Endpoint Assessment : Disabled
UC Proxy Sessions : 2
This platform has an ASA 5520 VPN Plus license.
This is a time-based license that will expire in 27 day(s).
Serial Number: JMX1101K2SU
Running Activation Key: 0x29249e66 0x500f33dc 0xcd79274e 0x534c7c93 0x81bc53bc
Configuration register is 0x1
Configuration has not been modified since last system restart.
CH-ASA#If you upgrade your ASA software to a bit more recent image first you can share the AnyConnect license (activation key) across both devices. Otherwise you would need to install a separate activation key on the second unit.
Sent from Cisco Technical Support iPad App -
Hi All
Im preparing a lab and I have 2 ASA 5520's. I have configured them for failover so the Primarys config will replicate over to the Secondary. They are connected via a 3560 switch. the switch ports are configured as access ports on vlan 1. Spanning-tree portfast is enabled
Firewall (Primary)
Cisco Adaptive Security Appliance Software Version 9.1(1)
Device Manager Version 7.1(2)
Compiled on Wed 28-Nov-12 10:38 by builders
System image file is "disk0:/asa911-k8.bin"
Config file at boot was "startup-config"
DEO-FW-01 up 5 hours 1 min
failover cluster up 5 hours 1 min
Hardware: ASA5520, 2048 MB RAM, CPU Pentium 4 Celeron 2000 MHz,
Internal ATA Compact Flash, 256MB
BIOS Flash M50FW080 @ 0xfff00000, 1024KB
Encryption hardware device : Cisco ASA-55xx on-board accelerator (revision 0x0)
Boot microcode : CN1000-MC-BOOT-2.00
SSL/IKE microcode : CNLite-MC-SSLm-PLUS-2.03
IPSec microcode : CNlite-MC-IPSECm-MAIN-2.08
Number of accelerators: 1
0: Ext: GigabitEthernet0/0 : address is 001e.f762.bc44, irq 9
1: Ext: GigabitEthernet0/1 : address is 001e.f762.bc45, irq 9
2: Ext: GigabitEthernet0/2 : address is 001e.f762.bc46, irq 9
3: Ext: GigabitEthernet0/3 : address is 001e.f762.bc47, irq 9
4: Ext: Management0/0 : address is 001e.f762.bc43, irq 11
5: Int: Not used : irq 11
6: Int: Not used : irq 5
Licensed features for this platform:
Maximum Physical Interfaces : Unlimited perpetual
Maximum VLANs : 150 perpetual
Inside Hosts : Unlimited perpetual
Failover : Active/Active perpetual
Encryption-DES : Enabled perpetual
Encryption-3DES-AES : Enabled perpetual
Security Contexts : 2 perpetual
GTP/GPRS : Disabled perpetual
AnyConnect Premium Peers : 2 perpetual
AnyConnect Essentials : Disabled perpetual
Other VPN Peers : 750 perpetual
Total VPN Peers : 750 perpetual
Shared License : Disabled perpetual
AnyConnect for Mobile : Disabled perpetual
AnyConnect for Cisco VPN Phone : Disabled perpetual
Advanced Endpoint Assessment : Disabled perpetual
UC Phone Proxy Sessions : 2 perpetual
Total UC Proxy Sessions : 2 perpetual
Botnet Traffic Filter : Disabled perpetual
Intercompany Media Engine : Disabled perpetual
Cluster : Disabled perpetual
This platform has an ASA 5520 VPN Plus license.
Here is the failover config
failover
failover lan unit primary
failover lan interface SFO GigabitEthernet0/3
failover replication http
failover link SFO GigabitEthernet0/3
failover interface ip SFO 10.10.16.25 255.255.255.248 standby 10.10.16.26
Here is the Show failover output
Failover On
Failover unit Primary
Failover LAN Interface: SFO GigabitEthernet0/3 (Failed - No Switchover)
Unit Poll frequency 1 seconds, holdtime 15 seconds
Interface Poll frequency 5 seconds, holdtime 25 seconds
Interface Policy 1
Monitored Interfaces 3 of 160 maximum
failover replication http
Version: Ours 9.1(1), Mate Unknown
Last Failover at: 12:53:27 UTC Mar 14 2013
This host: Primary - Active
Active time: 18059 (sec)
slot 0: ASA5520 hw/sw rev (2.0/9.1(1)) status (Up Sys)
Interface inside (10.10.16.1): No Link (Waiting)
Interface corporate_network_traffic (10.10.16.21): Unknown (Waiting)
Interface outside (193.158.46.130): Unknown (Waiting)
slot 1: empty
Other host: Secondary - Not Detected
Active time: 0 (sec)
Interface inside (10.10.16.2): Unknown (Waiting)
Interface corporate_network_traffic (10.10.16.22): Unknown (Waiting)
Interface outside (193.158.46.131): Unknown (Waiting)
Stateful Failover Logical Update Statistics
Link : SFO GigabitEthernet0/3 (Failed)
Here is the output for the secondary firewall
Cisco Adaptive Security Appliance Software Version 9.1(1)
Device Manager Version 6.2(5)
Compiled on Wed 28-Nov-12 10:38 by builders
System image file is "disk0:/asa911-k8.bin"
Config file at boot was "startup-config"
ciscoasa up 1 hour 1 min
failover cluster up 1 hour 1 min
Hardware: ASA5520, 2048 MB RAM, CPU Pentium 4 Celeron 2000 MHz,
Internal ATA Compact Flash, 256MB
BIOS Flash M50FW080 @ 0xfff00000, 1024KB
Encryption hardware device : Cisco ASA-55xx on-board accelerator (revision 0x0)
Boot microcode : CN1000-MC-BOOT-2.00
SSL/IKE microcode : CNLite-MC-SSLm-PLUS-2.03
IPSec microcode : CNlite-MC-IPSECm-MAIN-2.08
Number of accelerators: 1
0: Ext: GigabitEthernet0/0 : address is 0023.0477.12e4, irq 9
1: Ext: GigabitEthernet0/1 : address is 0023.0477.12e5, irq 9
2: Ext: GigabitEthernet0/2 : address is 0023.0477.12e6, irq 9
3: Ext: GigabitEthernet0/3 : address is 0023.0477.12e7, irq 9
4: Ext: Management0/0 : address is 0023.0477.12e3, irq 11
5: Int: Not used : irq 11
6: Int: Not used : irq 5
Licensed features for this platform:
Maximum Physical Interfaces : Unlimited perpetual
Maximum VLANs : 150 perpetual
Inside Hosts : Unlimited perpetual
Failover : Active/Active perpetual
Encryption-DES : Enabled perpetual
Encryption-3DES-AES : Enabled perpetual
Security Contexts : 2 perpetual
GTP/GPRS : Disabled perpetual
AnyConnect Premium Peers : 2 perpetual
AnyConnect Essentials : Disabled perpetual
Other VPN Peers : 750 perpetual
Total VPN Peers : 750 perpetual
Shared License : Disabled perpetual
AnyConnect for Mobile : Disabled perpetual
AnyConnect for Cisco VPN Phone : Disabled perpetual
Advanced Endpoint Assessment : Disabled perpetual
UC Phone Proxy Sessions : 2 perpetual
Total UC Proxy Sessions : 2 perpetual
Botnet Traffic Filter : Disabled perpetual
Intercompany Media Engine : Disabled perpetual
Cluster : Disabled perpetual
This platform has an ASA 5520 VPN Plus license.
Here is the failover config
failover
failover lan unit secondary
failover lan interface SFO GigabitEthernet0/3
failover replication http
failover link SFO GigabitEthernet0/3
failover interface ip SFO 10.10.16.26 255.255.255.248 standby 10.10.16.25
Here is the Show failover output
failover
failover lan unit secondary
failover lan interface SFO GigabitEthernet0/3
failover replication http
failover link SFO GigabitEthernet0/3
failover interface ip SFO 10.10.16.26 255.255.255.248 standby 10.10.16.25
Failover On
Failover unit Secondary
Failover LAN Interface: SFO GigabitEthernet0/3 (up)
Unit Poll frequency 1 seconds, holdtime 15 seconds
Interface Poll frequency 5 seconds, holdtime 25 seconds
Interface Policy 1
Monitored Interfaces 0 of 160 maximum
failover replication http
Version: Ours 9.1(1), Mate Unknown
Last Failover at: 12:58:31 UTC Mar 14 2013
This host: Secondary - Active
Active time: 3630 (sec)
slot 0: ASA5520 hw/sw rev (2.0/9.1(1)) status (Up Sys)
slot 1: empty
Other host: Primary - Not Detected
Active time: 0 (sec)
Stateful Failover Logical Update Statistics
Link : SFO GigabitEthernet0/3 (up)
interface g0/3 on both are up via the No shutdown command. However I get the following error No Active mate detected
please could someone help.
Many thanksHello James,
You have configured the IPs on the interfaces incorrectly.
Let me point it out
failover
failover lan unit primary
failover lan interface SFO GigabitEthernet0/3
failover replication http
failover link SFO GigabitEthernet0/3
failover interface ip SFO 10.10.16.25 255.255.255.248 standby 10.10.16.26
You are telling the Primary device use IP address 10.10.16.25 and the secondary firewall will be 10.10.26.26
Now let's see the configuration on the Secondary Unit?
failover
failover lan unit secondary
failover lan interface SFO GigabitEthernet0/3
failover replication http
failover link SFO GigabitEthernet0/3
failover interface ip SFO 10.10.16.26 255.255.255.248 standby 10.10.16.25
On the secondary you are saying the primary IP will be 10.10.16.26 and the secondary will be 10.10.16.25
You have it backwards and based on the output I would say you configured it on all of the interfaces like that
So please change it and make it the same on all of the interfaces so both devices know the same thing ( which IP they should use when they are primary and secondary, this HAVE to match )
Hope that I could help
Julio Carvajal -
ASA 5520 - LU allocate xlate failed - Failover unit reloads
We just had an issue with our failover unit reloading. In perusing the logs there were a number of %ASA-3-210007: LU allocate xlate failed, errors prior to the reload. These units had just had their OS upgraded to fix a DOS issue a few weeks ago. I have not seen the error since it reloaded. However, I was asked to report the issue just in case it is a bug in the new version of the OS.Two units in failover.
Cisco Adaptive Security Appliance Software Version 8.0(5)9
Device Manager Version 6.0(2)
Compiled on Mon 01-Feb-10 10:36 by builders
System image file is "disk0:/asa805-9-k8.bin"
Config file at boot was "startup-config"
CP-ASA up 17 days 21 hours
failover cluster up 17 days 22 hours
Hardware: ASA5520, 512 MB RAM, CPU Pentium 4 Celeron 2000 MHz
Internal ATA Compact Flash, 256MB
BIOS Flash M50FW080 @ 0xffe00000, 1024KB
Encryption hardware device : Cisco ASA-55x0 on-board accelerator (revision 0x0)
Boot microcode : CN1000-MC-BOOT-2.00
SSL/IKE microcode: CNLite-MC-SSLm-PLUS-2.03
IPSec microcode : CNlite-MC-IPSECm-MAIN-2.05
0: Ext: GigabitEthernet0/0 : address is 0025.45d7.6e62, irq 9
1: Ext: GigabitEthernet0/1 : address is 0025.45d7.6e63, irq 9
2: Ext: GigabitEthernet0/2 : address is 0025.45d7.6e64, irq 9
3: Ext: GigabitEthernet0/3 : address is 0025.45d7.6e65, irq 9
4: Ext: Management0/0 : address is 0025.45d7.6e66, irq 11
5: Int: Internal-Data0/0 : address is 0000.0001.0002, irq 11
6: Int: Internal-Control0/0 : address is 0000.0001.0001, irq 5
Licensed features for this platform:
Maximum Physical Interfaces : Unlimited
Maximum VLANs : 150
Inside Hosts : Unlimited
Failover : Active/Active
VPN-DES : Enabled
VPN-3DES-AES : Enabled
Security Contexts : 2
GTP/GPRS : Disabled
VPN Peers : 750
WebVPN Peers : 2
AnyConnect for Mobile : Disabled
AnyConnect for Linksys phone : Disabled
Advanced Endpoint Assessment : Disabled
UC Proxy Sessions : 2
This platform has an ASA 5520 VPN Plus license.
I noted a report on errors with verison 7 and a conflict between nat(0) and static commands. I don't show nat(0) being used on these units.
nat (public) 0 access-list NO_NAT
nat (public) 1 10.190.16.64 255.255.255.192
nat (public) 1 172.16.22.0 255.255.255.0
nat (dmz) 0 access-list NO_NAT
nat (dmz) 1 0.0.0.0 0.0.0.0
nat (csacelb) 0 access-list NO_NAT
nat (csacelb) 1 0.0.0.0 0.0.0.0
nat (app) 0 access-list NO_NAT
nat (app) 1 0.0.0.0 0.0.0.0
nat (db) 0 access-list NO_NAT
nat (db) 1 0.0.0.0 0.0.0.0
nat (internal) 0 access-list NO_NAT
nat (internal) 1 0.0.0.0 0.0.0.0
nat (management) 0 access-list NO_NAT
nat (management) 1 0.0.0.0 0.0.0.0
no crypto isakmp nat-traversal
static (app,dmz) 10.190.15.0 10.190.15.0 netmask 255.255.255.192
static (csacelb,public) 999.999.999.999 10.190.14.70 netmask 255.255.255.255 (The external address was replaced with 999.999.999.999 intentionally for this forum)
static (db,app) 10.190.16.0 10.190.16.0 netmask 255.255.255.192Do you have any solution ? we have the same problem.
Thanks . -
Cisco ASA 5520s in Cluster Outside interface stops sending traffic
Hi,
We are running a Pair of ASA 5520s in active/standby mode. In the last couple days the active device will just stop communicating on the outside interface. Because the rest of the interfaces are still up, it will not fail over, so we have to fail it manually. The secondary unit works and passes traffic correctly. We then reboot the Primary.
Then after some undetermined time, it happens again and we have to manually fail it the other way, reboot the affected ASA and wait for it to happen again.
We have a case with TAC but they have not been able to figure this one out. Has anyone else seen this behavior?
This is the version info:
Cisco Adaptive Security Appliance Software Version 8.4(7)
Device Manager Version 7.3(1)100
ThanksHi,
There are various possibilities on the ASA device which might be causing this issue:-
1) Block depletion
2) Memory depletion
Other things might be related to the external ISP as well.
Can we collect some outputs from the ASA device at the time when the issue is seen on the ASA device.
If you can share the output , i can have a look at it otherwise you can open a TAC case.
Thanks and Regards,
Vibhor Amrodia -
License with anyconnect on asa 5520
Dear All,
We have a single ASA 5510 with version 7.2 (3) in our network and configured many IPSEC site to site, IPSEC - remote access vpn and webvpn with SSL. Everything is working well.
ASA-5510# sh ver
Cisco Adaptive Security Appliance Software Version 7.2(3)
Device Manager Version 5.2(2)
Compiled on Wed 15-Aug-07 16:08 by builders
System image file is "disk0:/asa723-k8.bin"
Config file at boot was "startup-config"
ASA-5510-1 up 86 days 11 hours
Hardware: ASA5510, 256 MB RAM, CPU Pentium 4 Celeron 1600 MHz
Internal ATA Compact Flash, 256MB
BIOS Flash Firmware Hub @ 0xffe00000, 1024KB
Encryption hardware device : Cisco ASA-55x0 on-board accelerator (revision 0x0)
Boot microcode : CNlite-MC-Boot-Cisco-1.2
SSL/IKE microcode: CNlite-MC-IPSEC-Admin-3.03
IPSec microcode : CNlite-MC-IPSECm-MAIN-2.04
0: Ext: Ethernet0/0 : address is 0027.0d38.034e, irq 9
1: Ext: Ethernet0/1 : address is 0027.0d38.034f, irq 9
2: Ext: Ethernet0/2 : address is 0027.0d38.0350, irq 9
3: Ext: Ethernet0/3 : address is 0027.0d38.0351, irq 9
4: Ext: Management0/0 : address is 0027.0d38.0352, irq 11
5: Int: Internal-Data0/0 : address is 0000.0001.0002, irq 11
6: Int: Internal-Control0/0 : address is 0000.0001.0001, irq 5
Licensed features for this platform:
Maximum Physical Interfaces : Unlimited
Maximum VLANs : 100
Inside Hosts : Unlimited
Failover : Active/Active
VPN-DES : Enabled
VPN-3DES-AES : Enabled
Security Contexts : 2
GTP/GPRS : Disabled
VPN Peers : 250
WebVPN Peers : 25
This platform has an ASA 5510 Security Plus license.
===============================================================================================
As business improves we are now planning to upgrade our ASA 5510 to ASA 5520 ( 02 nos ver 8.2(5). With the new ASA 5520 we would be planning to buy Any connect vpn license as well.
Finally we will need on the ASA 5520 IPSEC site to site vpn, IPSEC - remote access vpn , clientless vpn with SSL & Any connect vpn license. What are the licences should i purchase inorder to have all the above services on the box with version 8.2(5) ?
suppose if i need to have cisco desktop software which is the license i should have along with other services?
Thanks in advanceI am just away from office .. Will provide same tomorrow...
Meanwhile "L-ASA-SSL-50=ASA 5500 SSL VPN 50 Premium User License" this is the licence i have procured from cisco. I would need
both Anyconnect vpn & SSL clientless should be working on the system. Hope i would acheive with the above license.
Below is the output i got when generated the Licence key. please clarrify. thanks in advance
Failover : Enabled
Encryption-DES : Enabled
Encryption-3DES-AES : Enabled
Security Contexts : 2
GTP/GPRS : Disabled
AnyConnect Premium Peers : 50
Other VPN Peers : 750
Advanced Endpoint Assessment : Disabled
AnyConnect for Mobile : Disabled
AnyConnect for Cisco VPN Phone : Disabled
Shared License : Disabled
UC Phone Proxy Sessions : Default
Total UC Proxy Sessions : Default
AnyConnect Essentials : Disabled
Botnet Traffic Filter : Disabled
Intercompany Media Engine : Disabled -
Does ASA 5520 support PKCS#11 ?
Hey.
does ASA 5520 VPN Plus (Cisco Adaptive Security Appliance Software Version 8.4(3) Device Manager Version 6.4(7))
support PKCS#11 ?
Thank you for answering;)You can purchase an AIP-SSM module for an ASA 5510 or 5520 to enable IDS/IPS functionality on the platform.
http://www.cisco.com/en/US/customer/prod/collateral/vpndevc/ps6032/ps6094/ps6120/ps6825/product_data_sheet0900aecd80404916_ps6120_Products_Data_Sheet.html
Maybe you are looking for
-
How can i add a new function to the Basic IVI class vi's?
I need to use the IVI vi's to control some instruments, let's say a DC Power Supply. Since there's a DC Power supplyclass, i can used those VI's but waht if one of the VI's does not contains all the functions that i need?. How can i add more function
-
WWSSO_APP_ADMIN.ls_login
Hi, I am calling WWSSO_APP_ADMIN.ls_login in wwsso_alert.password_reset_notification procedure by passing user and password parameters. I need to login internally with the random password generated by reset_password procedure and display change passw
-
Hi, We are executing ME2O transaction and passing Vendor, Assembly and Plant values as input.After execution when we want to create delivery. After giving storage location and quantity,we are getting an error which says "Error determining posting per
-
Hi all, I had gone through the pdf given fir OVS Search(F4)and i downloded the ready to use project.I deployed successfully and runned the project.But the problem is After giving AirlineId,a special window is comming with table ,but no data is there
-
Audition won't play (S/PDIF, OSX)
Hey there. I have this issue for some months now and tried to get around it several times but no solution turned out to work. I have tried to reset all audio devices, reconfigured everything, reinstalled the OSX and also, this doesn't work with Audit