Service Battery Error

Hi, I bought my macbook pro 13inch last year in January. After I upgraded to Mavericks around a month later I started getting service battery error. my cycle count is 418. So do i need to replace my battery or not?
Battery Information:
  Model Information:
  Serial Number:          W0*******3LC
  Manufacturer:          SMP
  Device Name:          bq20z451
  Pack Lot Code:          0
  PCB Lot Code:          0
  Firmware Version:          201
  Hardware Revision:          000a
  Cell Revision:          165
  Charge Information:
  Charge Remaining (mAh):          2793
  Fully Charged:          No
  Charging:          Yes
  Full Charge Capacity (mAh):          4411
  Health Information:
  Cycle Count:          418
  Condition:          Service Battery
  Battery Installed:          Yes
  Amperage (mA):          2576
  Voltage (mV):          12188
System Power Settings:
  AC Power:
  System Sleep Timer (Minutes):          100
  Disk Sleep Timer (Minutes):          10
  Display Sleep Timer (Minutes):          100
  Wake on AC Change:          No
  Wake on Clamshell Open:          Yes
  Wake on LAN:          Yes
  AutoPowerOff Delay:          14400
  AutoPowerOff Enabled:          1
  Current Power Source:          Yes
  Display Sleep Uses Dim:          Yes
  PrioritizeNetworkReachabilityOverSleep:          0
  Standby Delay:          4200
  Standby Enabled:          0
  Battery Power:
  System Sleep Timer (Minutes):          0
  Disk Sleep Timer (Minutes):          10
  Display Sleep Timer (Minutes):          20
  Wake on AC Change:          No
  Wake on Clamshell Open:          Yes
  AutoPowerOff Delay:          14400
  AutoPowerOff Enabled:          1
  Display Sleep Uses Dim:          Yes
  Reduce Brightness:          Yes
  Standby Delay:          4200
  Standby Enabled:          0
Hardware Configuration:
  UPS Installed:          No
AC Charger Information:
  Connected:          Yes
  ID:          0x0100
  Wattage (W):          60
  Revision:          0x0000
  Family:          0x00ba
  Serial Number:          0x00ed7ed9
  Charging:          Yes
<Personal Information Edited by Host>

Even though you're out of your warranty period (unless you purchased AppleCare) I would take the machine into your local Apple Store or an AASP and have them test the battery. 418 cycle counts is very high for a computer just 14 months old - you may have been letting the battery completely drain before plugging back up to mains or simply not following Apple's 'advice' on how to get the most mileage out of your battery.
Apple considers the battery to be a user consumable item - and if you've not treated your battery well, it may be reaching the point of half-way consumption, at least. The very worst that could happen is that Apple could recommend replacing your battery: and the cost isn't that great.
Clinton

Similar Messages

  • Service Battery error message for a battery that looks ok

    Hello,
    I have a 13 inch Macbook Pro with model number 5,5 and after upgrading my hard drive to a WD scorpio black 750GB and also adding 8 GB of Kingston memory I get a Service Battery error message. My OS is 10.6.8. The strange is that my battery is in a fairly good condition. I did check with coconut battery and it looks ok. I also add a print screen.
    Does anyone knows how can I remove this error message ? 
    Do I have to replace my battery ?

    Service battery means replace battery as soon as possible.
    Reset SMC and see whether it changes the notification.
    Reset SMC.     http://support.apple.com/kb/HT3964
    Choose the method for:
    "Resetting SMC on portables with a battery you should not remove on your own".
    Best.

  • Service battery error after upgrading to Mavericks

    Immediately after upgrading to Mavericks my Mid 2009 MacBook Pro that was purchased in September of 2013 received a service battery error.  The laptop will continue to charge while plugged in, but loses battery power at an alarming rate when unplugged.  Has Apple addressed this problem yet, and when can we expect a solution or repair for this?

    Battery Cycle Count
    Battery Life - Mavericks

  • Service battery error. Need help

    I bought this macbook pro in early 2011. Since then it has been working great but from last night I am seeing an error under my battery icon which says "Service Battery". Do I need to worry about this? Should I get a new battery or it can go by doing something else?
    P.S. My battery charge cycles has increased 700 cycles and I get around 2 hours on a 100% charged battery.

    It's telling you your battery is on it's last legs.
    Replace at your leisure.

  • 13" 2010 Macbook Service Battery Error

    I need a new battery huh.

    You should also ask this in the MacBook Pro forum. This is the forum for the 13” white and black plastic MacBooks that were discontinued in 2010. You should also post this question there to increase your chances of getting an answer.
    https://discussions.apple.com/community/notebooks/macbook_pro

  • Macbook Pro Battery-Service Battery Signal

    Hello,
    Ever since I upgraded to the mavericks operating system I have had an error message stating Service Battery. Does this mean I need to take my mid 2010 macbook pro lap top to purchase a new battery or is it an error created from the mavericks operating system? It just seems very co incidental this has occurred.
    Any help would be much apprecaited

      Try resetting SMC.
        Reset SMC.     http://support.apple.com/kb/HT3964
        Choose the method for:
       "Resetting SMC on portables with a battery you should not remove on your own".
    If this does not help, contact Apple.
    Genius Bar reservation
    http://www.apple.com/retail/geniusbar/

  • Satellite A200-X01 - Battery Error on Windows 7

    Hello, I woke my computer from sleep mode and found a popup stating I had a battery error.
    I was wondering if this is a common thing or if its a Windows 7 error?

    Hi DocWinters,
    What happens if you restart the notebook? Does the error still occur?
    I doubt its a common issue. In my opinion it sounds like that the battery needs replacing because its consumables and can only be charged/recharged 500 times I think.
    You can get a new battery from an authorized service provider! :)

  • HT6114 i have a problem with notification of service battery since i installed mavericks. My macbook air is 2012 version.

    i have a problem with notification of service battery since i installed mavericks. My macbook air is 2012 version. Any solution?

    This from the crash log
    Dyld Error Message:
      Library not loaded: /System/Library/Frameworks/Accounts.framework/Versions/A/Accounts
      Referenced from: /System/Library/StagedFrameworks/Safari/Safari.framework/Safari
    indicates there is a missing library on your system. What problems were you having before that caused you to delete Safari? How did you delete it?
    You're best bet in this case is to re-install the OS. While doing a re-install will not normally harm your user data having a good working backup in cases like this is essential.

  • X61 battery error

    The battery on my 3-month old X61 cannot be charged any more. The battery indicator blinks in yellow. The power manager just says "A battery error has occured. The battery cannot be charged. Please replace the battery." Anyone got similar problem?

    I have had the same problem with my X41 battery. I downloaded a update for my battery and when I installed the update my computer flashed my battery firmware making the battery incompatible with Xp. The sad part is that I have had my battery for more than a year which makes it out of warranty and the condition of the battery is greater than 50% so I do not see why I need to upgrade/buy a new battery like Lenovo is recommending.
    When I first recognized my problem I called Lenovo and they said it was probably my motherboard. So I had them replace my motherboard and my case. Then that seem to not fix the problem so they told me to reinstall Windows Xp. After reinstalling my OS my problems still persisted, so now I am in a battle with Lenovo to get me a new battery.
    So to everyone out there DO NOT UPGRADE YOUR BATTERY FIRMWARE! Unless you are comfortable knowing that Lenovo will not help you if it goes bad. If only lenovo would fix their patch I would be so much more happy right now.
    Ian
    Thinkpad X41
    Original description: P M 778(1.6GHz)LV, 512MB RAM, 60GB 4200rpm HD, 12.1in 1024x768 LCD, Intel 900, Intel 802.11abg wireless, Bluetooth/Modem, 1Gb Ethernet, Secure chip, Fingerprint reader, 8c Li-Ion batt, WinXP Tablet 2005
    Message Edited by ian on 02-12-2008 01:40 PM
    Thinkpad
    Original description: P M 778(1.6GHz)LV, 1.49GB RAM, 60GB 4200rpm HD, 12.1in 1024x768 LCD, Intel 900, Intel 802.11abg wireless, Bluetooth/Modem, 1Gb Ethernet, Secure chip, Fingerprint reader, 8c Li-Ion batt, WinXP Tablet 2005 Version: 5.1.2600 Service Pack 3 Build 2600 , BIOS: IBM 75ET60WW (2.60)

  • Helix Tablet battery problems - invalid, 0%, not charging, battery error

    Still having problems....
    I was hoping someone at Lenovo/ IBM could help me...
    I am unable to register a service request online.
    I have found the Lenovo website very difficult to use and there does not seem to be anybody to contact by email.
    Product: Lenovo Helix: 36971A1
    I have done a lot of research about this - I have read all the Lenovo help forums and have thoroughly been through their websites to try and resolve this issue but alas no luck. ...
    I have a battery issue - I realise that this has been written about extensively but like I said none of the methods suggested (i.e. software updates, BIOS update, uninstalling drivers etc) has solved my problem.
    I purchased my machine in June and up until 3 weeks ago it was working perfectly. But now...
    In short, the tablet part of my Lenovo Helix seems not to charge. Also Lenovo Settings app sems to have changed - now no option for maximising battery or to fully charge like people have been mentioning. I simply can't find this option anymore.
    -Computer seems to only run on battery from the keyboard dock
    -Once seperated from the keyboard dock, the Tablet section (having been plugged in to power point for hours only lasts about 30mins)
    -Battery level for tablet shows 0% plugged in - not charging
    -Keyboard dock seems to charge fine and shows true battery power level - charges to 100%
    -Once separated tablet part only works for short period before it dies, (turns off after around 30mins)
    -Every time computer is turned on, power settings icon displays saying : "there is a battery error"  click here for replacement"
    -Lenovo Settings and Companion app say "battery is invalid"
    -Last few days only - Lenovo Setting - as well as not displaying battery condition for Tablet only a -, is now also saying -Battery 1 was completing discharged and needs to be recharged. This may take ten hours or more.
    -When plugged in for a long period Lenovo Setting App shows power status at 50% and second battery attached
    - I tried charging over night for at least 10 hours, no luck.
    As I said the keyboard dock seems ok, problem seems to be with tablet battery or software  ????? .
    I would appreciate it greatly if someone could please respond and offer some help. Perhaps the problem can be solved remotely as I am not keen on sending my computer to Madrid to get fixed - I am worried I would be without my computer for weeks.
    Thank you in advance

    hi, I'm exactly similar problem.  it is really annoying. I have sent it to service centre once, they simply don't know and just reset the unit by pressing small hole at the tablet, the they do full recharge.  some how it works.
    later, at the same day occurred again and I tried replicate same process but no luck. then I follow instruction from one of the suggestion in this forum, it solved. it was 2-3 mth ago.
    now, after I upgrade to windows 8.1, the problem came back. all of this problem created from lenovo power management software together with their metro apps which setting what power management should do.
    the real culprits when you have setup some setting, then you undock or dock the tablet.. so I believe the software got confuse between the current setting with two unit (keyboard and tablet) especially if you ever play around with setting to extend the battery life which the power management will allow the battery to be charged not more than 50%. what the bad idea ... may not so bad but bad execution...
    we dont want this stupid geniuses ... we just want our unit working as when we purchase it. your latest driver is suck... big time... u should fire your engineer. .. pay 2k but got monkey ....

  • I want to writte C# code for 503 Service Unavailable error to web application page immediate close connection any page loaded

    Here is a ticket regarding our current client web application (  Image data add, edit , delete in folder with form data in MSSQL Database) that using code c#, web form, ajax, VS2008, MSSQL Server2008 , it appears that there is an error where the HTTP
    503 error occurs. 
    . Below is a conversation with Host Server support assistant.Can you take a look at it? 
    Ben (support) - Hi 
    Customer - We're having an issue with our windows host 
    Ben (support) - What's the issue? 
    Customer - 503 errors 
    Ben (support) - I am not getting any 503 errors on your site, is there a specific url to duplicate the error? 
    Customer - no, it comes and goes without any change Customer - could you have access to any logs ? 
    Ben (support) - Error logs are only available on Linux shared hosting, however with this error it may be related to you reaching your concurrent connections 
    Ben (support) - You can review more about this at the link \ 
    Customer - probably yes - how can we troubleshoot ? 
    Ben (support) - http://support.godaddy.com/help/article/3206/how-many-visitors-can-view-my-site-at-once 
    Ben (support) - This is something you need to review your code and databases to make sure they are closing the connections in a timely manner 
    Customer - we're low traffic, this is an image DB to show our product details to our customers 
    Customer - ahhhh, so we could have straying sessions ? 
    Ben (support) - Correct Customer - any way you could check if it's the case ? 
    Customer - because it was working previously 
    Ben (support) - We already know that's the case as you stated the 503 errors don't happen all the time if it were issue on the server the the 503 would stay. 
    Customer - so our 2/3 max concurrent users can max out the 200 sessions 
    Customer - correct ? 
    Customer - is there a timeout ? 
    Ben (support) - no that's not a time out concurrent connections are a little different then sessions and or connections. Lets say for an example you have 5 images on your site and 5 7 users come to your site this is not 7 concurrent connections but 35. They
    do close after awhile hence why the 503 error comes and goes. You can have these connections close sooner using code but this is something you have to research using your favorite search engine 
    Customer - thank you so much 
    Customer - I'm surprised that this just started a few weeks ago when we haven't changed anything for months 
    Customer - any changes from your side ? lowering of the value maybe ? 
    Customer - I'm trying to understand what I can report as a significant change 
    Ben (support) - We haven't touched that limit in years 
    Ben (support) - This could just be more users to your site than normal or even more images 
    Customer - I was thinking that could be it indeed 
    Customer - so I need to research how to quickly close connections when not needed 
    Ben (support) - Correctly 
    Ben (support) - correct 
    Customer - thanks !! 
    Ben (support) - Your welcome 
     Analysis : 
     The link provided tells us : All Plesk accounts are limited to 200 simultaneous visitors. 
     From what Ben (support) says and a little extra research, if those aren't visitors but connections then it's quite easy to max out, especially if the connections aren't closed when finished using. I'd suggest forwarding this to Kasem to see what he thinks. 
    Cheers, 
    Customer

    Hi Md,
    Thank you for posting in the MSDN forum.
    >>
    I want to writte C# code for 503 Service Unavailable error to web application page immediate close connection any page loaded.
    Since
    Visual Studio General Forum which discuss VS IDE issue, I am afraid that you post the issue in an incorrect forum.
    To help you find the correct forum, would you mind letting us know more information about this issue? Which kind of web app you develop using C# language? Is it an ASP.NET Web Application?
    If yes, I suggest you could post the issue directly on
    ASP.NET forum, it would better support your issue.
    Thanks for your understanding.
    Best Regards,
    We are trying to better understand customer views on social support experience, so your participation in this interview project would be greatly appreciated if you have time. Thanks for helping make community forums a great place.
    Click HERE to participate the survey.

  • How do you resolve Financial Management service validation error in EPM ?

    Does anyone know how to resolve Financial Management service validation error from EPM Diagnostic Report?
    Environment:
    Quad-Core AMD Processor 2.2 GHz (Server Machine)
    5 GB RAM
    Server 2003 Standard 32-Bit SP2 (also tried in Enterprise)
    Application Server:
    WebLogic Server 9.2 Custom Installation (with Add-Ins)
    http://www.oracle.com/technology/software/products/ias/htdocs/wls_main.html
    Database:
    Oracle 10gR2 (Standard Installation per step-by-step guide from Oracle)
    http://www.oracle.com/technology/software/products/database/index.html
    Hyperion EMP System 11.1.1.3:
    Installer
    Foundation Services (4 Files )
    EMP Architect
    Financial Management, Planning, Financial Reporting and Web Analysis (primarily interested in FM)
    http://www.oracle.com/technology/software/products/bi/performance-management/index.html
    The following are the sequences of steps carried out during the Installation and Configuration of EPM:
    1)     Installed the Server along with its respective SP2 – Shutdown the machine
    2)     Assigned IP and DNS addresses
    3)     Installed Window components by ticking Application Server Console, Enable COM+ access, IIS and DNS
    4)     Run “dcpromo” to create a Domain Controller with default values and assigned a domain name – Shutdown the machine
    5)     Installed Weblogic Server 9.2 and configure it using Configuration Wizard – Selected “test environment” and ticked default “listening port” – Shutdown the machine
    6)     Basic installation of Oracle Database 10gR2 using Step-by-Step guide provided by Oracle and carried out Password Management steps. After installation, I then created a user “oracle” and assigned it to ora_dba User Group with the required Local Security Policies – “log on as a batch job” and “Act as part of operating system”
    7)     Logged into database and acknowledge the licensing window – Shutdown the machine
    8)     Restarted the machine and checked all relevant and newly installed Database and WebLogic services are running.
    9)     Started Installing EPM components by double clicking “InstallTool.cmd” and selected all relevant components at ONCE as per Installation Guide – Result: - All selected EPM components were successfully installed without errors or exceptions
    10)     At the end of installation window, I carried out the configuration in the following scearios:
    Scenario 1: Configuration all at Default settings
    Scenario 2: Configuration all, except “Application Server” I selected the WebLogic9.2
    Scenario 3: Configuration all, except “Application Server” and “Workspace Web Server” were being Welogic9.2 and IIS HTTP
    RESULT: After all numerous installations, all came down to ONE ERROR from “Diagnostic Report” stating the following:
    Financial Management:
    FAILED SVR: HFM Service Validation Check if HFM service in working state.
    Error: Error message: <03/11/2010 05:32:26 PM> CreateApplicationCAS... Failed at line: 2
    Recommended Action: Make sure HAT utility is working. 1 s
    I then simply ignored this error and tried to deploy an Application, all worked fine until you get to the point at “Job Console” where you need to press “Refresh” button. Progress remained at 12% until it got timedout after 300 seconds and force attempt of refreshing resulting in “aborted” job with the following error:
    Error Reference Number: {DB3940F5-2D4A-46AB-A370-77F82F121BBA}
    Num: 0x8000ffff;Type: 0;DTime: 4/12/2010 4:39:58 PM;Svr: PBAR;File: CHsvDataSourceImpl.cpp;Line: 196;Ver: 11.1.1.3.0.2413;
    Num: 0x8000ffff;Type: 0;DTime: 4/12/2010 4:40:07 PM;Svr: PBAR;File: CHsxServer.cpp;Line: 1276;Ver: 11.1.1.3.0.2413;
    Num: 0x8000ffff;Type: 0;DTime: 4/12/2010 4:40:07 PM;Svr: PBAR;File: CHsxServer.cpp;Line: 1190;Ver: 11.1.1.3.0.2413;
    Num: 0x8000ffff;Type: 0;DTime: 4/12/2010 4:40:07 PM;Svr: PBAR;File: AgentHelper.cpp;Line: 728;Ver: 11.1.1.3.0.2413;
    Num: 0x8000ffff;Type: 1;DTime: 4/12/2010 4:40:08 PM;Svr: PBAR;File: CHfmAwbAgent.cpp;Line: 744;Ver: 11.1.1.3.0.2413;
    This is, I believe preventing me from deploying Consolidation Apps, including Sample Application provided with EPM Downloads. I have tried installing and configuring by components. All failed with the same outcome.
    I have been working on this effortlessly in different combinations to get at least one Financial Management Application get deployed so I could enhance my learning adventure. As it stands, I am not sure where to get help and completely lost in the World of Oracle. I am also come to wonder whether “Free Downloads of EPM” are indeed, is “complete and is in working-state” or do I need a licence to use for personal learning experience? Are there different downloads for different needs or/users For example, eDelivery downloads are different from OTN Agreement downloads?
    I have downloaded the files from following URL:
    http://www.oracle.com/technology/software/products/bi/performance-management/index.html
    I am completely lost and all services are up and running and not sure what I am missing!! Any assistance will be greatly appreciated.
    Many Thanks
    BT
    Edited by: user8973921 on 13-Apr-2010 05:08
    Edited by: user8973921 on 13-Apr-2010 10:56
    Edited by: user8973921 on 14-Apr-2010 02:30

    I am having exactly the same problem using Windows 2003 Standard editions SP2. Is there anyone who knows a possible solution for this? The effect on HFM is that is not possible to create an application, since I always get an error that says "Server execution failed"
    Error Reference Number: {E68F87E6-588E-4665-862C-AAB02CB299DA}
    Num: 0x80080005;Type: 0;DTime: 12/3/2009 5:21:47 PM;Svr: KINGTUT;File: CHsxServerImpl.cpp;Line: 3522;Ver: 11.1.1.3.0.2413;
    Num: 0x80080005;Type: 0;DTime: 12/3/2009 5:21:47 PM;Svr: KINGTUT;File: CHsxServer.cpp;Line: 1115;Ver: 11.1.1.3.0.2413;
    Num: 0x80080005;Type: 0;DTime: 12/3/2009 5:21:47 PM;Svr: KINGTUT;File: CHsxServer.cpp;Line: 857;Ver: 11.1.1.3.0.2413;
    Num: 0x80080005;Type: 0;DTime: 12/3/2009 5:21:47 PM;Svr: KINGTUT;File: CHsxClient.cpp;Line: 2106;Ver: 11.1.1.3.0.2413;

  • Failed to open service OracleDEV102TNSListener , error 1060

    Dear Consultants,
    I have been trying to install ECC6 , Oracle on Windows 2003, and my Hardware is RAM --2 GB
    HDD -- 300GB
    I am having intel duo core processor and iam using Gigabyte motherboard,Intel chipset.
    My Installations stops at Import_Abap phase, following are the logs ,
    <b>ERROR 2007-03-10 04:47:46
    CJS-30022  Program 'Migration Monitor' exits with error code 103. For details see log file(s) import_monitor.java.log, import_monitor.log.
    ERROR 2007-03-10 04:47:47
    FCO-00011  The step runMigrationMonitor with step key |NW_Onehost|ind|ind|ind|ind|0|0|NW_Onehost_System|ind|ind|ind|ind|1|0|NW_CreateDBandLoad|ind|ind|ind|ind|9|0|NW_ABAP_Import_Dialog|ind|ind|ind|ind|5|0|NW_ABAP_Import|ind|ind|ind|ind|0|0|runMigrationMonitor was executed with status ERROR .
    INFO 2007-03-10 05:03:18
    An error occured and the user decide to stop.\n Current step "|NW_Onehost|ind|ind|ind|ind|0|0|NW_Onehost_System|ind|ind|ind|ind|1|0|NW_CreateDBandLoad|ind|ind|ind|ind|9|0|NW_ABAP_Import_Dialog|ind|ind|ind|ind|5|0|NW_ABAP_Import|ind|ind|ind|ind|0|0|runMigrationMonitor</b>".
    I have set the all the Environment variables , i run r3trans -d and the result is
    <b>C:\Documents and Settings\devadm>r3trans -d
    This is r3trans version 6.13 (release 700 - 20.02.06 - 16:15:00).
    unicode enabled version
    2EETW169 no connect possible: "connect failed with DBLI_RC_LOAD_LIB_FAILED."
    r3trans finished (0012).</b>
    <b>I also run r3trans -x and the result is.
    4 ETW000  [dbsloci.    ,00000]  *** ERROR => CONNECT failed with sql error '12541'
    4 ETW000                                                                              21  1.098448
    4 ETW000  [dev trc     ,00000]  Try to connect with default password                 142  1.098590
    4 ETW000  [dev trc     ,00000]  Connecting as SAPSR3/<pwd>@DEV on connection 0 (nls_hdl 0) ... (dbsl 700 240106)
    4 ETW000                                                                              22  1.098612
    4 ETW000  [dev trc     ,00000]  Nls CharacterSet                 NationalCharSet              C      EnvHp      ErrHp ErrHpBatch
    4 ETW000                                                                              23  1.098635
    4 ETW000  [dev trc     ,00000]    0 UTF8                                                      1   0244CF08   0245243C   02451CC4
    4 ETW000                                                                              24  1.098659
    4 ETW000  [dev trc     ,00000]  server_detach(con_hdl=0,stale=0,svrhp=02463484)       14  1.098673
    4 ETW000  [dev trc     ,00000]  Detaching from DB Server (con_hdl=0,svchp=02451C10,srvhp=02463484)
    4 ETW000                                                                              19  1.098692
    4 ETW000  [dev trc     ,00000]  Deallocating server context handle 02463484           16  1.098708
    4 ETW000  [dev trc     ,00000]  Allocating server context handle                      15  1.098723
    4 ETW000  [dev trc     ,00000]  Attaching to DB Server DEV (con_hdl=0,svchp=02451C10,svrhp=02463484)
    4 ETW000                                                                              29  1.098752
    4 ETW000  [dev trc     ,00000]  Tue Mar 13 04:38:09 2007                         1093335  2.192087
    4 ETW000  [dboci.c     ,00000]  *** ERROR => OCI-call 'OCIServerAttach' failed: rc = 12541
    4 ETW000                                                                              19  2.192106
    4 ETW000  [dbsloci.    ,00000]  *** ERROR => CONNECT failed with sql error '12541'
    4 ETW000                                                                              19  2.192125
    4 ETW000  [dblink      ,00431]  ***LOG BY2=>sql error 12541  performing CON [dblink#3 @ 431]
    4 ETW000                                                                             176  2.192301
    4 ETW000  [dblink      ,00431]  ***LOG BY0=>ORA-12541: TNS:no listener [dblink#3 @ 431]
    4 ETW000                                                                              19  2.192320
    2EETW169 no connect possible: "DBMS = ORACLE                           --- dbs_ora_tnsname = 'DEV'"</b>
    Event Viewer result is
    <b>----
    Faulting application isqlplussvc.exe, version 1.0.7.0, faulting module msvcrt.dll, version 7.0.3790.0, fault address 0x0003113b.</b>
    finally in SAPINST logs i could see
    <b>
    Starting tnslsnr: please wait...
    Failed to open service <OracleDEV102TNSListener>, error 1060.
    TNSLSNR for 32-bit Windows: Version 10.2.0.1.0 - Production
    System parameter file is C:\oracle\DEV\102\network\admin\listener.ora
    Log messages written to C:\oracle\DEV\102\network\log\listener.log
    Listening on: (DESCRIPTION=(ADDRESS=(PROTOCOL=ipc)(PIPENAME=
    .\pipe\DEV.WORLDipc)))
    Listening on: (DESCRIPTION=(ADDRESS=(PROTOCOL=ipc)(PIPENAME=
    .\pipe\DEVipc)))
    Listening on: (DESCRIPTION=(ADDRESS=(PROTOCOL=tcp)(HOST=DEV)(PORT=1527)))
    Connecting to (ADDRESS=(PROTOCOL=IPC)(KEY=DEV.WORLD))
    STATUS of the LISTENER
    Alias                     LISTENER
    Version                   TNSLSNR for 32-bit Windows: Version 10.2.0.1.0 - Production
    Start Date                10-MAR-2007 01:29:29
    Uptime                    0 days 0 hr. 0 min. 3 sec
    Trace Level               off
    Security                  ON: Local OS Authentication
    SNMP                      OFF
    Listener Parameter File   C:\oracle\DEV\102\network\admin\listener.ora
    Listener Log File         C:\oracle\DEV\102\network\log\listener.log
    Listening Endpoints Summary...
      (DESCRIPTION=(ADDRESS=(PROTOCOL=ipc)(PIPENAME=
    .\pipe\DEV.WORLDipc)))
      (DESCRIPTION=(ADDRESS=(PROTOCOL=ipc)(PIPENAME=
    .\pipe\DEVipc)))
      (DESCRIPTION=(ADDRESS=(PROTOCOL=tcp)(HOST=DEV)(PORT=1527)))
    Services Summary...
    Service "DEV" has 1 instance(s).
      Instance "DEV", status UNKNOWN, has 1 handler(s) for this service...
    The command completed successfully</b>
    Please suggest for the possible workaround, as you can see i have tried everything.
    Regards,

    Dear Umesh,
    I have triggered the Installation again, still the problem remains unresolved,
    PLEASE CONFIRM THAT I AM USING INTEL CORE DUO PROCESSOR , does it have any dependcies or prerequisites.
    pasting the last few lines of  logs of SAPAPPL1_15, where i got the error in ABAP IMPORT.
    DbSl Trace: ORA-4031 occurred when executing SQL statement (parse error offset=0)
    (DB) ERROR: DDL statement failed
    (CREATE UNIQUE INDEX "VDBEPI_EU~0" ON "VDBEPI_EU" ( "MANDT", "BUKRS", "RBELKPFD", "RPOSNR" ) TABLESPACE PSAPSR3 STORAGE (INITIAL 16384 NEXT 0000002560K MINEXTENTS 0000000001 MAXEXTENTS 2147483645 PCTINCREASE 0 ) )
    DbSlExecute: rc = 99
      (SQL error 4031)
      error message returned by DbSl:
    ORA-04031: unable to allocate 40 bytes of shared memory ("shared pool","CREATE UNIQUE INDEX "VDBEPI_...","Typecheck","qcsqlpath: qcsAddSqlPath")
    (DB) INFO: disconnected from DB
    E:\usr\sap\NAJ\SYS\exe\uc\NTI386\R3load.exe: job finished with 1 error(s)
    E:\usr\sap\NAJ\SYS\exe\uc\NTI386\R3load.exe: END OF LOG: 20070517090126
    ===================================================
    IMPORT_MONITOR.JAVA logs.
    Import Monitor jobs: running 2, waiting 35, completed 34, failed 1, total 72.
    Loading of 'SAPAPPL1_15' import package: ERROR
    Import Monitor jobs: running 1, waiting 35, completed 34, failed 2, total 72.
    Loading of 'SAPAPPL2_5' import package: ERROR
    Import Monitor jobs: running 0, waiting 35, completed 34, failed 3, total 72.
    Import Monitor jobs: running 1, waiting 34, completed 34, failed 3, total 72.
    Import Monitor jobs: running 2, waiting 33, completed 34, failed 3, total 72.
    Import Monitor jobs: running 3, waiting 32, completed 34, failed 3, total 72.
    Loading of 'D021T' import package: OK
    Import Monitor jobs: running 2, waiting 32, completed 35, failed 3, total 72.
    Import Monitor jobs: running 3, waiting 31, completed 35, failed 3, total 72.
    Loading of 'SAPAPPL1_12' import package: OK
    Import Monitor jobs: running 2, waiting 31, completed 36, failed 3, total 72.
    Import Monitor jobs: running 3, waiting 30, completed 36, failed 3, total 72.
    Loading of 'SAPSSEXC_4' import package: OK
    Import Monitor jobs: running 2, waiting 30, completed 37, failed 3, total 72.
    Import Monitor jobs: running 3, waiting 29, completed 37, failed 3, total 72.
    Loading of 'SAPSSEXC_6' import package: OK
    Import Monitor jobs: running 2, waiting 29, completed 38, failed 3, total 72.
    Regards,

  • Service Battery Goofiness

    Last evening I was using my MacBook, watching videos on Youtube and what not. I had plans that night, so I just closed the lid and got up and left. The computer usually falls asleep and when i get home I just open the lid, and everything is right where I left it. Yesterday I was gone for about four hours, I don't remember how full the battery was when I left, but when I got home, I opened the lid, and screen flashed, and the computer when to sleep. I tried turning it on and nothing happened. I plugged it into the wall and it turned on. The battery read 0%, and it said "service battery," which was weird, it only has about 151 cycles and 88% health. As it was charging it said it only had 9 minutes, and I was thinking no way is it going to charge fully in nine minutes. I charged it till it said about 19% and I took it off the wall; the battery read 94% full, and about 3.5 hours which is normal. It no longer said to service the battery. I turned it off, let it fully charge, and called it a night. This morning I got up, turned it on, the battery was full and said three and some hours of life left. I started to check my email, Facebook, Youtube, and all that stuff. Then suddenly the computer just goes to sleep again. The lid was open, and the battery was still about 95%-ish. I plugged it into the wall and turned it on, the battery read 0% full and "service battery," as I am typing this, it jumped back up to 94% and no longer says I need to service the battery. I usually, let the battery get down to halfway before I charge it, and I always take it off the charger when the battery is full. Could this be an issue with Lion maybe, or the battery. It's a new battery as of February. Any ideas?

    Hi, I have lost 2% on my maximum battery charge. It now *suddenly* charges up to 98% claiming that the battery has to be serviced - again. This is already my 3rd !! battery in 3 years.
    //MBP early 2008 - the worst MacBook (pro) Apple ever made)//

  • After upgrading to OSX 10.7.4 it says "Service Battery"

    Just upgraded to 10.7.4 and my MacBook Pro (mid 2010) now says "Service Battery". I have
    reset the SMC, with no results
    completely discharged then recharget the battery, no results
    Repaired disk permissions, no results
    Verified the disk, appears to be OK so won't repair it.
    The battery status was "Good" until I updated. 
    Anyone with the same issue? Any suggestion on how to solve this?

    vrlink wrote:
    Hi,
    It all is a lot confusing because in that article and others it says the battery of my MBP (builtin battery) doesn't need to be calibrated.
    I actually followed the directions in
    http://support.apple.com/kb/HT1490
    reference from your post above " pre-calibrated "  at time of purchase.
    This does not preclude " re-calibrating" as general maintenance.
    more info on battery health: https://discussions.apple.com/thread/1764220?threadID=1764220
    MacBook Pro, Mac OS X (10.7.4), 2.4GHz IntelCore i5 320 HD 8GB RAM ParallelsDesktop6.0

Maybe you are looking for

  • Device Not Recognized by Windows?

    Received Ipod video for Christmas. When I plug Ipod into USB, nothing happens. We have installed software and performed update through Apple.com. Have also done Windows update. When we click on Itunes on desktop, it does not recognize device. It appe

  • Smart Playlist for Music Videos

    I've fought and fought with iTunes and I cannot figure out how to make a Smart Playlist that JUST HAS MUSIC videos. I'd like to have a list that just has my music videos in it, but I want it to be a smart playlist so I do not have to keep updating it

  • Shared members issue

    Hi to all, I've a Problem with the shared members in a excel spreadsheet. I need to see all members in a specific dimension (shared members included). using members selection dialog box, i'm using the view method "by generation name" and the output o

  • My iPhone does not appear in the sharing drop down

    I downloaded the Mavericks yesterday and I try to use the new map feature. Unfortunately, when I want to share the map with the directions my iPhone 5 doesn't appear in the drop down menu. I'm using the latest software for my iPhone. Does anyone has

  • Command F - Find Feature

    I need to know if there is a way to change one of the columns in the find window FROM Last Opened TO Date Modified. When I do a search for an item, i don't want to know the date it was last opened, I want to know the last date it was modified that wa