Set a DHCP gateway for WRT300N
Dear Friends Hello I have to networks with IP ranges 192.169.1.x & 192.168.1.x I want to connect this two networks,the problem is that the ip address of gateway is 192.168.1.1 and the IP address of router(WRT300N) is 192.168.1.2 I don't have windows server,and i can't set static IP for all of users How can I set a gateway in DHCP settings ?
You can't do this with your WRT. It is a broadband router with limited configuration options. One limitation is that the DHCP server in the WRT always uses its own IP address as gateway IP address. You cannot freely configure the DHCP server. It is supposed to be a broadband router, i.e. it is supposed to host the internet connection and thus be the default gateway.
Technically, you only want to route a subnet differently and not the whole internet. Thus the default route/gateway is the wrong place to modify.
The proper solution would be to add a static route for the other subnet on all client computers. Then the computers will correctly route the traffic. The proper solution would also be to run your own DHCP servers to do the IP assignment there and not assign any gateway address at all.
If you don't want to do that you can only add a static route on the routers to reroute the traffic for the other subnet.
First of all, please renumber the IP subnet 192.169.1.* to a private IP address, e.g. 192.168.2.*. 192.169.1.* is a public IP address and should not be used for private addresses.
Now say, you have the computers with the modem link sitting on 192.168.1.1/255.255.255.0 and 192.168.2.1/255.255.255.0.
The routers with DHCP server enabled sit on 192.168.1.2/255.255.255.0 and 192.168.2.2/255.255.255.0.
Now add a static route on the router 192.168.1.2 on the advanced routing page:
route destination LAN IP 192.168.2.0, subnet mask 255.255.255.0 to gateway 192.168.1.1 on the LAN interface.
likewise on 192.168.2.2 add:
route destination LAN IP 192.168.1.0, subnet mask 255.255.255.0 to gateway 192.168.2.1 on LAN interface.
With those two routes in place you should be able to use the Diagnostics tools on the Administration tab of the router to ping or traceroute IP addresses in the other subnet.
These routes should also redirect the traffic from the computers to the other subnet. You should make sure that the firewalls on all computers are not configured to block ICMP (in particular ICMP redirects). The router will tell the computers the correct gateway address for the traffic, i.e. the computer will only send the first packet to the router and then learns that the correct destination is the computer with the modem link and forwards everything directly there. Many firewalls are overzealous and unnecessarily block ICMP breaking many IP mechanism for troubleshooting and optimization. Therefore: make sure your firewalls are turned off or correctly configured. Otherwise you unnecessarily route all your traffic to the other subnet through the router as well.
Again: i would rather recommend to set up your own DHCP server and set static routes on the computers or push the routes through DHCP.
Similar Messages
-
Airport DHCP Reservations for Windows 7 PCs
I have several devices on my Airport network, and I have set up DHCP reservations for ~15 of the devices. Every device is handling the reservation properly and utilizing the IP address associated to the devices MAC address except for my wife's Toshiba laptop running Windows 7 Home Premium.
I am specifying the laptop's IP address I would like to reserve (10.0.1.6) and including the laptop's WiFi MAC address (I've checked it many times and I have it correct). When the PC attempts to attach to the Airport network, it is able to attach but not gain the IP address.
If I do not set up a reservation the laptop does obtain the next available address (10.0.1.18), so I don't believe that I have any other setup or authentication errors along the way.
Further, I do not have any issues reserving an address for my Windows XP laptop.
Any suggestions? Thanks, JohnDisregard. I simply reserved a different address and it is now working. The Windows PC seems to think that there was already something on the network with 10.0.1.6 (there was not).
-
Setting up Oracle XML Gateway for EBS 12.1.3
Hi Experts,
We are currently working on R12.1.3 and was asked to check on how to setup/integrate XML Gateway on R12.1.3.
I have gone though many pages of this forums and checked the support ID's as given below :
Installing Oracle XML Gateway and Oracle Workflow with Oracle Applications 11i [ID 152775.1] --> Its for 11i, don't find the same for R12.
Oracle XML Gateway Release Notes, Release 12.1.3 --> does not help giving the information on how to setup XML Gateway
Found the below link but not sure if this is what was asked and looks like Client Desktop Installation.
11i - 12 How To Download and Install the Latest Oracle Workflow Builder (Client Tool) and XML Gateway Message Designer for E-Business (Doc ID 261028.1)
I don't know much about Oracle XML Gateway and how to integrate this to EBS R12, I am not able to find how to integrate this with the existing R12.1.3.
Please someone guide me though this.
Also, I would like to know what benefit could we get with XML Gateway setup when we have the workflows and similar setups already available with R12.1.3, and is there is a way to work out the XML messages inside R12.1.3 without setting up XML Gateway.
Experts please clarify the above and guide me and would highly appreciate for a quick response.
Regards,
SandyHi Sandy,
Did you try the documentation library? The following gives you a detail explanation on how you can setup XML gateway on R12.1.3:
http://docs.oracle.com/cd/B53825_08/current/acrobat/121ecxug.pdf
In addition, also please review notes:
Oracle XML Gateway Release Notes for Release 12.1.3 (Doc ID 1096991.1)
11i - 12 How To Download and Install the Latest Oracle Workflow Builder (Client Tool) and XML Gateway Message Designer for E-Business (Doc ID 261028.1)
Also please review the Forum Search, as this will allow a better understanding.
Forum Search: XML Gateway
Thanks &
Best Regards, -
Use Linux server NAT gateway for Windows domain?
Well, I'm kinda new to this...
I don't have a hardware router appliance, and I am short on Windows licences, so I figured that a Linux box would make a cheap NAT router (and firewall). I remembered that Linux generally can supply DNS & DHCP out of the box - but come to think of it, they are both optional.
I didn't stop to think that the DHCP could be on the windows domain controller, but I guess it would make excellent sense to keep AD & DNS & DHCP all together on one DC... the linux box would just become a 'router appliance', nothing more.
The second DC just DNS and AD, no DHCP - and both of them ( andall clients) pointing to the inside IP of the Linux box as the gateway.
Thanks very much for all the suggestions, I think I'm on track now :-)We're short on machines and I want to set up a lab network.
I have a 2008R2 and a 2008Standard that I want to use as domain controllers (R2 as 'primary', so to speak).
I understand its bad practice to make DC's multi-homed, but need to set up an internet gateway to my lab network - and I was wondering if it's possible to use a handy Linux box (Centos 6) as the NAT gateway & DHCP. (Using the Linux box as an Internet gateway for my Windows domain)
Has anybody ever done this successfully? I guess the trick would be getting DNS updates passed to the Windows NS from the Linux DHCP server??
This topic first appeared in the Spiceworks Community -
RV320: Need to use as gateway for multiple subnets
We just purchased an RV320 as a replacement/upgrade to an RV042. Our Internet connection was upgraded to 200Mbps and the RV042 wouldn't handle that throughput.
Our internal network has 4 subnets, all connected via a layer 3 switch. The RV320 is connected to one of those subnets and is the default gateway for the entire network.
The RV042 had a "multiple subnets" setting that allowed it to perform NAT for the directly connected subnet and the other 3 subnets in our network. We would just add the other networks to the list in the RV042 and everything was fine.
The RV320 doesn't seem to have the same functionality (or am I missing something?). It looks like there is some sort of multiple subnet support, but when we try to add another subnet the interface seems to be asking us to define a single IP address in that subnet (an IP address for the router?) as if all subnets will be directly attached to the router using VLANs (which is not the case in our network).
We can set up the "advanced routing" option to define the other 3 internal subnets and how to route to them, etc. but will the RV320 perform NAT for the other subnets without any adidtional configuration?
Can anyone shed any light on this?
Many thanks!Precept,
My name is Ismael, iam with Small Business Support Center. I like to start by asking is there a particular reason that the switch is handling Layer 3/or DHCP? Normally when an RV042 is implemented you would need a Layer 3 switch as the RV042 only supports one DHCP scope.In addition all The RV0XX series does not support 802.1q VLAN.
With RV320 you can setup multiple subnets under advance routing and still allow for it to pass DHCP for all of your 4 subnets and create 801.2q Vlan subinterfaces . Setting RV320 in this manner can create an ease in managing the network.
If you are considering the RV320 to do Layer 3 / DHCP simply create your 4 Vlans or subnets. Add them to the DHCP scope and enable DHCP server for all subnets. Switch would have to be configured to Layer 2 for this to work. The link below is a knowledge portal that could assist in creating DHCP and Vlans. Hope this helps you.
http://sbkb.cisco.com/ -
This is my first time using any windows server os and am in the process of setting up a virtual home lab through vmware with 3 server 2012 r2s running.
I have all three connected to the internet and able to ping one another.
I have a domain set up on one and am trying to get one of the others "promoted" to it... Im receiving the error: You must supply an account user name.
I created users within the active directory users and computers.. in domain admins and users and a few other places just troubleshooting... no luck. :(
What am I missing here? Any and all input is much appreciated thank you!Alright sorry for the delay, I was given exact setup instructions so I figured I'd be good to go but I'm still hung up basically at the same spot.
Here's the setup guide:
Two servers, a domain controller and an application server. Follow
the setup instructions below.
1. Open your server’s Networking and Sharing Center.
2. Double-click the Ethernet connection to open the Ethernet Status dialog box.
3. Click Properties to open the Ethernet Properties dialog box.
4. Double-click Internet Protocol Version 4 (TCP/IPv4) to open the Internet Protocol
Version 4 (TCP/IPv4) Properties dialog box.
5. Enter the following information:
IP address: 192.168.1.50
Subnet mask: 255.255.255.0
Preferred DNS server: 192.168.1.50
6. Click on the Advanced button.
7. In the IP addresses section, click the Add button.
8. When the TCP/IP Address dialog box opens, enter the following information:
IP address: 192.168.100.55
Subnet mask: 255.255.255.0
9. Change the name of the server to RWDC0x, where x is the number of your table from
1 to 6
Installing Active Directory
The RWDC0x virtual machine will be the primary Active Directory domain Controller and
the DNS server. Therefore, to configure the RWDC0x server, use the following steps:
1. Login to RWDC0x as Administrator.
2. On the Server Manager console, open the Manage menu and click Add Roles and
Features.
3. When the Add Roles and Features Wizard starts, click Next.
4. On the Select installation type page, click Next.
5. On the Select destination server page, click Next.
6. On the Select server roles page, click to select Active Directory Domain Services and
click Next.
When the Add Roles and Features Wizard dialog box opens, click Add Features.
8. Back on the Select server roles page, click to select DNS Server and click Next.
9. When the Add Roles and Features Wizard dialog box opens, click Add Features.
10. Back at the Select server roles page, click Next.
11. On the Select features page, click Next.
12. On the Active Directory Domain Services page, click Next.
13. On the DNS Server page, click Next.
14. On the Confirm installation selections page, click Install.
15. When the installation is complete, click Close.
16. On the Server Manager console, click the Tools menu (upper left) and click DNS.
17. When the DNS Manager console opens, right-click RWDC0x and click New Zone.
18. When the New Zone Wizard appears, click Next.
2
19. On the Zone Type page, Primary zone will already be selected. Click Next.
20. On the Forward or Reverse Lookup Zone page, Forward lookup zone will already be
selected. Click Next.
21. For the Zone name, type contoso.com and click Next.
22. On the Zone File page, click Next.
23. On the Dynamic Update page, click Next.
24. When the wizard is complete, click Finish.
25. On the Server Manager console, click the Yellow Exclamation Symbol and click
Promote this server to a domain controller.
26. When the Active Directory Domain Services Configuration Wizard starts, click Add a
new forest.
27. In the Root domain name text box, type contoso.com. Click Next.
28. On the Domain Controllers Options page, for the Directory Services Restore Mode
(DSRM) password boxes, type Password01. Click Next.
29. On the DNS Options page, click Next.
30. On the Additional Options page, click Next.
31. On the Paths page, click Next.
32. On the Review Options page, click Next.
33. On the Prerequisite Check page, click Install.
34. After the computer reboots itself, login to RWDC01 as contoso\administrator with the
password of Password01.
35. Open the DNS Manager console.
36. In the DNS Manager console, expand RWDC01, expand Forward Lookup Zones, and
click contoso.com. Then right-click contoso.com and click Properties.
37. When the Contoso.com Properties dialog box opens, click the Change button.
38. When the Change Zone Type dialog box opens, select Store the zone in Active
Directory and click OK.
39. When it asks if you want the zone to become Active Directory integrated, click Yes.
40. For Dynamic Updates, select Non-secure and secure.
41. Click OK to close the contoso.com Properties dialog box.
42. Click Reverse Lookup Zones. Then right-click Reverse Lookup Zones and click New
Zone.
43. When the wizard opens, click Next.
44. On the Zone Type page, click Next.
45. On the Active Directory Zone Replication Scope page, click Next.
46. On the Reverse Lookup Zone Name page, click Next.
47. On the Reverse Lookup Zone Name page, type 192.168.1 in the Network ID and click
Next.
48. On the Dynamic Update page, click Next.
49. When the wizard is complete, click Finish.
Installing DHCP
The RWDC0x will also be the primary DHCP server for the virtual environment. Therefore,
use the following steps to install and configure DHCP on the RWDC0x:
1. Login to RWDC0x as Administrator.
2. On the Server Manager console, open the Manage menu and click Add Roles and
3
Features.
3. When the Add Roles and Features Wizard starts, click Next.
4. On the Select installation type page, click Next.
5. On the Select destination server page, click Next.
6. On the Select server roles page, click to select DHCP and click Next.
7. When the Add Roles and Features Wizard dialog box opens, click Add Features.
8. Back at the Select server roles page, click Next.
9. On the Select features page, click Next.
10. On the DHCP page, click Next.
11. On the DNS Server page, click Next.
12. On the Confirm installation selections page, click Install.
13. When the installation is complete, click Close.
14. Using Server Manager, open the DHCP console.
15. Expand the rwdc0x.contoso.com node.
16. Right-click IPv4 and click New Scope.
17. When the New Scope Wizard starts, click Next.
18. For the Name, type Main Scope.
19. For the Start IP address, type 192.168.1.30. For the End IP address, type 192.168.1.40.
Click Next.
20. On the Add Exclusions and Delay page, click Next.
21. On the Lease Duration, change the lease duration to 1 day. Click Next.
22. On the Configure DHCP Options page, click Yes, I want to configure these options
now. Click Next.
23. On the Router (Default Gateway) page, click Next.
24. On the Domain Name and DNS Servers page, type contoso.com for the Parent domain.
In the IP address, type 192.168.1.50, and click Add. Click Next.
25. On the WINS Servers page, click Next.
26. On the Activate Scope, make sure Yes, I want to active this scope now, and click Next.
27. When the wizard is complete, click Finish.
28. In the DHCP console, right-click rwdc01.contoso.com and click Authorize.
29. Close the DHCP console.
Creating a Software Folder
Because you will not have Internet access, you must create a Software folder to hold
the software and share the folder using the following steps:
1. On RWDC0x, create a folder called C:\Software.
2. Open the properties dialog box for the C:\Software folder
3. Share the Software folder using the name Software.
4. Assign the Allow Full Control share permission to the Everyone special identity.
5. Copy all files and folders from the Software folder from your instructor’s thumb drive to
the Software folder.
6. Close the Explorer windows.
Now, configure your application server.
1. Login to Server01 as Administrator.
2. Open your server’s Networking and Sharing Center.
4
3. Double-click the Ethernet connection to open the Ethernet Status dialog box.
4. Click Properties to open the Ethernet Properties dialog box.
5. Double-click Internet Protocol Version 4 (TCP/IPv4) to open the Internet Protocol
Version 4 (TCP/IPv4) Properties dialog box.
6. Enter the following information:
IP address: 192.168.1.60
Subnet mask: 255.255.255.0
Preferred DNS server: 192.168.1.50
7. Click OK to close the Internet Protocol Version 4 (TCP/IPv4) Properties dialog box.
8. Click Close to close Ethernet Statusdialog box.
9. Double-click the computer name to open the System Properties dialog box.
10. Click Change to open the Computer Name/Domain Changes dialog box.
11. Type Server01 in the Computer name text box.
12. Click Domain and type Contoso.com in the text box. Click OK.
13. When it asks for a name and password of an account with permissions to join the
domain, use contoso.com\administrator and Password01. Click OK.
14. When the Welcome to the contoso.com domain message appears, click OK.
15. When a message appears stating that you must restart your computer, click OK.
16. Click the Close button to close the System Properties dialog box.
17. When it says that you must restart your computer, click Restart Now.
I went through this once and I couldnt get past "12. Click Domain and type Contoso.com in the text box. Click OK" without an error.
I uninstalled all machines and VMware entirely, reinstalled VMware and then reinstalled machines, went though the guide again, same error when trying to connect the app server to the contoso.com domain.
Here's a screenshot of the error:
I also tried changing both machines to bridged connection, no luck, as well as NAT connection, still no luck.
Any help is greatly appreciated... Thanks guys! -
How do you set up Port Forwarding for ARD 2.2 in AEB N?
Help,
I'm a novice at Apple Remote Desktop (ARD) - not an IT guy, so it has to be pretty basic and detailed.
How do you set up Port Forwarding for ARD 2.2 on the Apple Airport Extreme BS router, 802.11 N. I have one at each end of the internet connection. At one end I have an Airport Extreme N router with 2 macs and eventually 1 windows XP machine (if I can) that I would like to be able to connect to over the interenet (the clients) and at the other end, I have a Mac with ARD 2.2 installed also with an Airport Extreme N router. Note: Both routers use Static IP addresses and all computers use static IP's internally not through DHCP. What are the settings or directions to do this.
I have read and printed out the directions for Configuration of ARD 3.0 that are posted many times in the ARD discusion group, but it uses a Linksys router ( http://www.starkpr.com/ard.htm posted by Dave Sawyer). The Mac router is different, particularly with the place to set a Private IP address. I'm not sure about alot of things, but especially about the Private IP address, what number do I set it to, the one that is in my Network connections list? It automatically changes to a different number in AE N setup for Port Forwarding (by one) as if it is not suppose to the same?????
Are there any directions available that are as straight forward for the Airport Extreme N router, as the one's that are listed here for the Linksys Router's? ( http://www.starkpr.com/ard.htm )
Any and All help will be greatly appreciated.
P.S. I know I should have 3.0 but bought 2.2 just weeks before 3.0 came out and they would not give me an upgrade price, so I'm waiting for 4.0 to upgrade.
Thanks,
JimTry the following for each AirPort Extreme ...
AEBSn - Port Mapping Setup
To setup port mapping on an 802.11n AirPort Extreme Base Station (AEBSn), either connect to the AEBSn's wireless network or temporarily connect directly, using an Ethernet cable, to one of the LAN port of the AEBSn, and then use the AirPort Utility, in Manual Setup, to make these settings:
1. Reserve a DHCP-provided IP address for the host device.
Internet > DHCP tab
o On the DHCP tab, click the "+" (Add) button to enter DHCP Reservations.
o Description: <enter the desired description of the host device>
o Reserve address by: MAC Address
o Click Continue.
o MAC Address: <enter the MAC (what Apple calls Ethernet ID if you are using wired or AirPort ID if wireless) hardware address of the host computer>
o IPv4 Address: <enter the desired IP address>
o Click Done.
2. Setup Port Mapping on the AEBSn.
Advanced > Port Mapping tab
o Click the "+" (Add) button
o Service: <choose the appropriate service from the Service pop-up menu>
o Public UDP Port(s): 3283
o Public TCP Port(s): 3283
o Private IP Address: <enter the IP address of the host server>
o Private UDP Port(s): 3283
o Private TCP Port(s): 3283
o Click "Continue"
o Click the "+" (Add) button
o Service: <choose the appropriate service from the Service pop-up menu>
o Public UDP Port(s):
o Public TCP Port(s): 5900
o Private IP Address: <enter the IP address of the host server>
o Private UDP Port(s):
o Private TCP Port(s): 5900
o Click "Continue"
o Click the "+" (Add) button
o Service: <choose the appropriate service from the Service pop-up menu>
o Public UDP Port(s):
o Public TCP Port(s): 5988
o Private IP Address: <enter the IP address of the host server>
o Private UDP Port(s):
o Private TCP Port(s): 5988
o Click "Continue"
(ref: "Well Known" TCP and UDP ports used by Apple software products) -
Error fetching data from a foxpro db using Oracle Gateway for ODBC
Hi.
I have an 10.2.0.1 database an a 11.2.0 Oracle Gateway for ODBC installed and configured.
The dblink test works fine, I can connect with the foxpro database because if I execute desc centros I can see the
columns of table centros.
The problem comes when I try to execute Select * from centros@fox1;
A syntax error is returned ([Microsoft][ODBC Visual FoxPro Driver]Syntax error. {42000,NativeErr = 200})
I paste down the output of the trace file with HS_FDS_TRACE_LEVEL=255
If I run select codcen from centros@fox1; another error is shown. Tell me if you want the other trace file.
select codcen from centros@fox1
ERROR en lÝnea 1:
ORA-00904: "CODCEN": identificador no vßlido
Oracle Corporation --- JUEVES MAY 31 2012 13:11:24.765
Heterogeneous Agent Release
11.2.0.1.0
Oracle Corporation --- JUEVES MAY 31 2012 13:11:24.750
Version 11.2.0.1.0
Entered hgogprd
HOSGIP for "HS_FDS_TRACE_LEVEL" returned "255"
Entered hgosdip
setting HS_OPEN_CURSORS to default of 50
setting HS_FDS_RECOVERY_ACCOUNT to default of "RECOVER"
setting HS_FDS_RECOVERY_PWD to default value
setting HS_FDS_TRANSACTION_LOG to default of HS_TRANSACTION_LOG
setting HS_IDLE_TIMEOUT to default of 0
setting HS_FDS_TRANSACTION_ISOLATION to default of "READ_COMMITTED"
setting HS_NLS_NCHAR to default of "UCS2"
setting HS_FDS_TIMESTAMP_MAPPING to default of "DATE"
setting HS_FDS_DATE_MAPPING to default of "DATE"
setting HS_RPC_FETCH_REBLOCKING to default of "ON"
setting HS_FDS_FETCH_ROWS to default of "100"
setting HS_FDS_RESULTSET_SUPPORT to default of "FALSE"
setting HS_FDS_RSET_RETURN_ROWCOUNT to default of "FALSE"
setting HS_FDS_PROC_IS_FUNC to default of "FALSE"
setting HS_FDS_CHARACTER_SEMANTICS to default of "FALSE"
setting HS_FDS_MAP_NCHAR to default of "TRUE"
setting HS_NLS_DATE_FORMAT to default of "YYYY-MM-DD HH24:MI:SS"
setting HS_FDS_REPORT_REAL_AS_DOUBLE to default of "FALSE"
setting HS_LONG_PIECE_TRANSFER_SIZE to default of "65536"
setting HS_SQL_HANDLE_STMT_REUSE to default of "FALSE"
setting HS_FDS_QUERY_DRIVER to default of "TRUE"
setting HS_FDS_SUPPORT_STATISTICS to default of "FALSE"
Parameter HS_FDS_QUOTE_IDENTIFIER is not set
setting HS_KEEP_REMOTE_COLUMN_SIZE to default of "OFF"
setting HS_FDS_GRAPHIC_TO_MBCS to default of "FALSE"
setting HS_FDS_MBCS_TO_GRAPHIC to default of "FALSE"
Default value of 32 assumed for HS_FDS_SQLLEN_INTERPRETATION
setting HS_CALL_NAME_ISP to "gtw$:SQLTables;gtw$:SQLColumns;gtw$:SQLPrimaryKeys;gtw$:SQLForeignKeys;gtw$:SQLProcedures;gtw$:SQLStatistics;gtw$:SQLGetInfo"
setting HS_FDS_DELAYED_OPEN to default of "TRUE"
setting HS_FDS_WORKAROUNDS to default of "0"
Exiting hgosdip, rc=0
ORACLE_SID is "DAVID"
Product-Info:
Port Rls/Upd:1/0 PrdStat:0
Agent:Oracle Database Gateway for ODBC
Facility:hsa
Class:ODBC, ClassVsn:11.2.0.1.0_0008, Instance:DAVID
Exiting hgogprd, rc=0
hostmstr: 2057416704: HOA After hoagprd
hostmstr: 2057416704: HOA Before hoainit
Entered hgoinit
HOCXU_COMP_CSET=1
HOCXU_DRV_CSET=178
HOCXU_DRV_NCHAR=1000
HOCXU_DB_CSET=178
HOCXU_SEM_VER=102000
Entered hgolofn at 2012/05/31-13:11:25
Exiting hgolofn, rc=0 at 2012/05/31-13:11:25
HOSGIP for "HS_OPEN_CURSORS" returned "50"
HOSGIP for "HS_FDS_FETCH_ROWS" returned "100"
HOSGIP for "HS_LONG_PIECE_TRANSFER_SIZE" returned "65536"
HOSGIP for "HS_NLS_NUMERIC_CHARACTER" returned ".,"
HOSGIP for "HS_KEEP_REMOTE_COLUMN_SIZE" returned "OFF"
HOSGIP for "HS_FDS_DELAYED_OPEN" returned "TRUE"
HOSGIP for "HS_FDS_WORKAROUNDS" returned "0"
HOSGIP for "HS_FDS_MBCS_TO_GRAPHIC" returned "FALSE"
HOSGIP for "HS_FDS_GRAPHIC_TO_MBCS" returned "FALSE"
Invalid value of 32 given for HS_FDS_SQLLEN_INTERPRETATION
treat_SQLLEN_as_compiled = 1
Exiting hgoinit, rc=0 at 2012/05/31-13:11:25
hostmstr: 2057416704: HOA After hoainit
hostmstr: 2057416704: HOA Before hoalgon
Entered hgolgon at 2012/05/31-13:11:25
reco:0, name:SYSTEM, tflag:0
Entered hgosuec at 2012/05/31-13:11:25
Exiting hgosuec, rc=0 at 2012/05/31-13:11:25
HOSGIP for "HS_FDS_RECOVERY_ACCOUNT" returned "RECOVER"
HOSGIP for "HS_FDS_TRANSACTION_LOG" returned "HS_TRANSACTION_LOG"
HOSGIP for "HS_FDS_TIMESTAMP_MAPPING" returned "DATE"
HOSGIP for "HS_FDS_DATE_MAPPING" returned "DATE"
HOSGIP for "HS_FDS_CHARACTER_SEMANTICS" returned "FALSE"
HOSGIP for "HS_FDS_MAP_NCHAR" returned "TRUE"
HOSGIP for "HS_FDS_RESULTSET_SUPPORT" returned "FALSE"
HOSGIP for "HS_FDS_RSET_RETURN_ROWCOUNT" returned "FALSE"
HOSGIP for "HS_FDS_PROC_IS_FUNC" returned "FALSE"
HOSGIP for "HS_FDS_REPORT_REAL_AS_DOUBLE" returned "FALSE"
using SYSTEM as default value for "HS_FDS_DEFAULT_OWNER"
HOSGIP for "HS_SQL_HANDLE_STMT_REUSE" returned "FALSE"
Entered hgocont at 2012/05/31-13:11:25
HS_FDS_CONNECT_INFO = "Prueba_Foxpro"
RC=-1 from HOSGIP for "HS_FDS_CONNECT_STRING"
Entered hgogenconstr at 2012/05/31-13:11:25
dsn:Prueba_Foxpro, name:SYSTEM
optn:
Entered hgocip at 2012/05/31-13:11:25
dsn:Prueba_Foxpro
Exiting hgocip, rc=0 at 2012/05/31-13:11:25
##>Connect Parameters (len=39)<##
## DSN=Prueba_Foxpro;
#! UID=SYSTEM;
#! PWD=*
Exiting hgogenconstr, rc=0 at 2012/05/31-13:11:25
Entered hgopoer at 2012/05/31-13:11:26
hgopoer, line 233: got native error 0 and sqlstate 01000; message follows...
[*Microsoft][Administrador de controladores ODBC] El controlador no admite una versión de ODBC distinta de la que la necesita la aplicación (vea SQLSetEnvAttr)*. {01000}
Exiting hgopoer, rc=0 at 2012/05/31-13:11:26
hgocont, line 2686: calling SqlDriverConnect got sqlstate 01000
Entered hgolosf at 2012/05/31-13:11:26
ODBC Function-Available-Array 0xFFFE 0x00FF 0xFF00 0xAA7F 0x03B3 0x0000
0x0000 0x0000 0x0000 0x0000 0x0000 0x0000
0x0000 0x0000 0x0000 0x0000 0x0000 0x0000
0x0000 0x0000 0x0000 0x0000 0x0000 0x0000
0x0000 0x0000 0x0000 0x0000 0x0000 0x0000
0x0000 0x0000 0x0000 0x0000 0x0000 0x0000
0x0000 0x0000 0x0000 0x0000 0x0000 0x0000
0x0000 0x0000 0x0000 0x0000 0x0000 0x0000
0x0000 0x0000 0x0000 0x0000 0x0000 0x0000
0x0000 0x0000 0x0000 0x0000 0x0000 0x0000
0x0000 0x0000 0xEE00 0x395C
Exiting hgolosf, rc=0 at 2012/05/31-13:11:26
DriverName:VFPODBC.DLL, DriverVer:06.86.0001
DBMS Name:Visual FoxPro, DBMS Version:03.00.0000
Exiting hgocont, rc=0 at 2012/05/31-13:11:26 with error ptr FILE:hgocont.c LINE:2686 ID:SQLDriverConnect
Entered hgopoer at 2012/05/31-13:11:26
hgopoer, line 233: got native error 0 and sqlstate HYC00; message follows...
[Microsoft][ODBC Visual FoxPro Driver]Driver not capable {HYC00}
Exiting hgopoer, rc=0 at 2012/05/31-13:11:26
hgolgon, line 795: calling SQLGetInfo got sqlstate HYC00
SQLGetInfo returns N for SQL_CATALOG_NAME
Exiting hgolgon, rc=0 at 2012/05/31-13:11:26 with error ptr FILE:hgolgon.c LINE:795 ID:GetInfo: Support catalogs
hostmstr: 2036506624: HOA After hoalgon
RPC Calling nscontrol(0), rc=0
hostmstr: 2036506624: RPC Before Upload Caps
hostmstr: 2036506624: HOA Before hoaulcp
Entered hgoulcp at 2012/05/31-13:11:26
Entered hgowlst at 2012/05/31-13:11:26
Exiting hgowlst, rc=0 at 2012/05/31-13:11:26
SQLGetInfo returns 0x0 for SQL_OWNER_USAGE
TXN Capable:1, Isolation Option:0x2
SQLGetInfo returns 0 for SQL_MAX_SCHEMA_NAME_LEN
SQLGetInfo returns 128 for SQL_MAX_TABLE_NAME_LEN
SQLGetInfo returns 0 for SQL_MAX_PROCEDURE_NAME_LEN
SQLGetInfo returns ` (0x60) for SQL_IDENTIFIER_QUOTE_CHAR
SQLGetInfo returns Y for SQL_COLUMN_ALIAS
16 instance capabilities will be uploaded
capno:1964, context:0x00000000, add-info: 0
capno:1989, context:0x00000000, add-info: 0
capno:1991, context:0x0001ffff, add-info: 0
capno:1992, context:0x0001ffff, add-info: 1, translation:"`"
capno:3042, context:0x00000000, add-info: 0, translation:"42"
capno:3047, context:0x00000000, add-info: 0, translation:"57"
capno:3049, context:0x00000000, add-info: 0, translation:"59"
capno:3050, context:0x00000000, add-info: 0, translation:"60"
capno:3066, context:0x00000000, add-info: 0
capno:3067, context:0x00000000, add-info: 0
capno:3068, context:0x00000000, add-info: 0
capno:3069, context:0x00000000, add-info: 0
capno:3500, context:0x00000001, add-info: 91, translation:"42"
capno:3501, context:0x00000001, add-info: 93, translation:"57"
capno:3502, context:0x00000001, add-info: 107, translation:"59"
capno:3503, context:0x00000001, add-info: 110, translation:"60"
Exiting hgoulcp, rc=0 at 2012/05/31-13:11:26
hostmstr: 2036506624: HOA After hoaulcp
hostmstr: 2036506624: RPC After Upload Caps
hostmstr: 2036506624: RPC Before Upload DDTR
hostmstr: 2036506624: HOA Before hoauldt
Entered hgouldt at 2012/05/31-13:11:27
NO instance DD translations were uploaded
Exiting hgouldt, rc=0 at 2012/05/31-13:11:27
hostmstr: 2036506624: HOA After hoauldt
hostmstr: 2036506624: RPC After Upload DDTR
hostmstr: 2036506624: RPC Before Begin Trans
hostmstr: 2036506624: HOA Before hoabegn
Entered hgobegn at 2012/05/31-13:11:27
tflag:0 , initial:1
hoi:0x12f094, ttid (len 54) is ...
00: 54455354 2E524547 52455353 2E524442 [TEST.REGRESS.RDB]
10: 4D532E44 45562E55 532E4F52 41434C45 [MS.DEV.US.ORACLE]
20: 2E434F4D 2E663033 63383037 372E392E [.COM.f03c8077.9.]
30: 34342E37 3735 [44.775]
tbid (len 10) is ...
0: 09002C00 07030000 0104 [..,.......]
Exiting hgobegn, rc=0 at 2012/05/31-13:11:27
hostmstr: 2036506624: HOA After hoabegn
hostmstr: 2036506624: RPC After Begin Trans
hostmstr: 2036506624: RPC Before Describe Table
hostmstr: 2036506624: HOA Before hoadtab
Entered hgodtab at 2012/05/31-13:11:27
count:1
table: CENTROS
Entered hgopdsc at 2012/05/31-13:11:27
Describing procedure CENTROS
Output hoada
hgopdsc, line 1426: NO hoada to print
Exiting hgopdsc, rc=942 at 2012/05/31-13:11:27
The hoada for table CENTROS follows...
hgodtab, line 904: NO hoada to print
Exiting hgodtab, rc=0 at 2012/05/31-13:11:27
hostmstr: 2036506624: HOA After hoadtab
hostmstr: 2036506624: RPC After Describe Table
hostmstr: 2036506624: RPC Before SQL Bundling
hostmstr: 2036506624: HOA Before hoxpars
Entered hgopars, cursor id 1 at 2012/05/31-13:11:27
type:0
SQL text from hgopars, id=1, len=23 ...
00: 53454C45 4354202A 2046524F 4D202243 [SELECT * FROM "C]
10: 454E5452 4F5322 [ENTROS"]
Exiting hgopars, rc=0 at 2012/05/31-13:11:28
hostmstr: 2036506624: HOA After hoxpars
hostmstr: 2036506624: RPC After SQL Bundling
hostmstr: 2036506624: RPC Before SQL Bundling
hostmstr: 2036506624: HOA Before hoxopen
Entered hgoopen, cursor id 1 at 2012/05/31-13:11:28
hgoopen, line 87: NO hoada to print
Deferred open until first fetch.
Exiting hgoopen, rc=0 at 2012/05/31-13:11:28
hostmstr: 2036506624: HOA After hoxopen
hostmstr: 2036506624: HOA Before hoxdscr
Entered hgodscr, cursor id 1 at 2012/05/31-13:11:28
Allocate hoada @ 023E983C
Entered hgopoer at 2012/05/31-13:11:28
hgopoer, line 233: got native error 0 and sqlstate HY091; message follows...
[Microsoft][ODBC Visual FoxPro Driver]*Descriptor type out of range* {HY091}
Exiting hgopoer, rc=0 at 2012/05/31-13:11:28
hgodscr, line 615: calling SQLColAttribute got sqlstate HY091
Entered hgopcda at 2012/05/31-13:11:28
Column:1(codcen): dtype:1 (CHAR), prc/scl:8/0, nullbl:0, octet:8, sign:1, radix:0
Exiting hgopcda, rc=0 at 2012/05/31-13:11:28
Entered hgopoer at 2012/05/31-13:11:28
hgopoer, line 233: got native error 0 and sqlstate HY091; message follows...
[Microsoft][ODBC Visual FoxPro Driver]Descriptor type out of range {HY091}
Exiting hgopoer, rc=0 at 2012/05/31-13:11:28
hgodscr, line 615: calling SQLColAttribute got sqlstate HY091
Entered hgopcda at 2012/05/31-13:11:28
Column:2(litcen): dtype:1 (CHAR), prc/scl:45/0, nullbl:0, octet:45, sign:1, radix:0
Exiting hgopcda, rc=0 at 2012/05/31-13:11:28
Entered hgopoer at 2012/05/31-13:11:28
hgopoer, line 233: got native error 0 and sqlstate HY091; message follows...
[Microsoft][ODBC Visual FoxPro Driver]Descriptor type out of range {HY091}
Exiting hgopoer, rc=0 at 2012/05/31-13:11:28
hgodscr, line 615: calling SQLColAttribute got sqlstate HY091
Entered hgopcda at 2012/05/31-13:11:28
Column:3(codpos): dtype:1 (CHAR), prc/scl:5/0, nullbl:0, octet:5, sign:1, radix:0
Exiting hgopcda, rc=0 at 2012/05/31-13:11:28
Entered hgopoer at 2012/05/31-13:11:28
hgopoer, line 233: got native error 0 and sqlstate HY091; message follows...
[Microsoft][ODBC Visual FoxPro Driver]Descriptor type out of range {HY091}
Exiting hgopoer, rc=0 at 2012/05/31-13:11:28
hgodscr, line 615: calling SQLColAttribute got sqlstate HY091
Entered hgopcda at 2012/05/31-13:11:28
Column:4(codprov): dtype:1 (CHAR), prc/scl:2/0, nullbl:0, octet:2, sign:1, radix:0
Exiting hgopcda, rc=0 at 2012/05/31-13:11:28
Entered hgopoer at 2012/05/31-13:11:28
hgopoer, line 233: got native error 0 and sqlstate HY091; message follows...
[Microsoft][ODBC Visual FoxPro Driver]Descriptor type out of range {HY091}
Exiting hgopoer, rc=0 at 2012/05/31-13:11:28
hgodscr, line 615: calling SQLColAttribute got sqlstate HY091
Entered hgopcda at 2012/05/31-13:11:28
Column:5(codmun): dtype:1 (CHAR), prc/scl:3/0, nullbl:0, octet:3, sign:1, radix:0
Exiting hgopcda, rc=0 at 2012/05/31-13:11:28
Entered hgopoer at 2012/05/31-13:11:28
hgopoer, line 233: got native error 0 and sqlstate HY091; message follows...
[Microsoft][ODBC Visual FoxPro Driver]Descriptor type out of range {HY091}
Exiting hgopoer, rc=0 at 2012/05/31-13:11:28
hgodscr, line 615: calling SQLColAttribute got sqlstate HY091
Entered hgopcda at 2012/05/31-13:11:28
Column:6(codecol): dtype:1 (CHAR), prc/scl:2/0, nullbl:0, octet:2, sign:1, radix:0
Exiting hgopcda, rc=0 at 2012/05/31-13:11:28
Entered hgopoer at 2012/05/31-13:11:28
hgopoer, line 233: got native error 0 and sqlstate HY091; message follows...
[Microsoft][ODBC Visual FoxPro Driver]Descriptor type out of range {HY091}
Exiting hgopoer, rc=0 at 2012/05/31-13:11:28
hgodscr, line 615: calling SQLColAttribute got sqlstate HY091
Entered hgopcda at 2012/05/31-13:11:28
Column:7(codesin): dtype:1 (CHAR), prc/scl:2/0, nullbl:0, octet:2, sign:1, radix:0
Exiting hgopcda, rc=0 at 2012/05/31-13:11:28
Entered hgopoer at 2012/05/31-13:11:28
hgopoer, line 233: got native error 0 and sqlstate HY091; message follows...
[Microsoft][ODBC Visual FoxPro Driver]Descriptor type out of range {HY091}
Exiting hgopoer, rc=0 at 2012/05/31-13:11:28
hgodscr, line 615: calling SQLColAttribute got sqlstate HY091
Entered hgopcda at 2012/05/31-13:11:28
Column:8(cb): dtype:1 (CHAR), prc/scl:4/0, nullbl:0, octet:4, sign:1, radix:0
Exiting hgopcda, rc=0 at 2012/05/31-13:11:28
Entered hgopoer at 2012/05/31-13:11:28
hgopoer, line 233: got native error 0 and sqlstate HY091; message follows...
[Microsoft][ODBC Visual FoxPro Driver]Descriptor type out of range {HY091}
Exiting hgopoer, rc=0 at 2012/05/31-13:11:28
hgodscr, line 615: calling SQLColAttribute got sqlstate HY091
Entered hgopcda at 2012/05/31-13:11:28
Column:9(cs): dtype:1 (CHAR), prc/scl:4/0, nullbl:0, octet:4, sign:1, radix:0
Exiting hgopcda, rc=0 at 2012/05/31-13:11:28
Entered hgopoer at 2012/05/31-13:11:28
hgopoer, line 233: got native error 0 and sqlstate HY091; message follows...
[Microsoft][ODBC Visual FoxPro Driver]Descriptor type out of range {HY091}
Exiting hgopoer, rc=0 at 2012/05/31-13:11:28
hgodscr, line 615: calling SQLColAttribute got sqlstate HY091
Entered hgopcda at 2012/05/31-13:11:28
Column:10(digitocon): dtype:1 (CHAR), prc/scl:2/0, nullbl:0, octet:2, sign:1, radix:0
Exiting hgopcda, rc=0 at 2012/05/31-13:11:28
Entered hgopoer at 2012/05/31-13:11:28
hgopoer, line 233: got native error 0 and sqlstate HY091; message follows...
[Microsoft][ODBC Visual FoxPro Driver]Descriptor type out of range {HY091}
Exiting hgopoer, rc=0 at 2012/05/31-13:11:28
hgodscr, line 615: calling SQLColAttribute got sqlstate HY091
Entered hgopcda at 2012/05/31-13:11:28
Column:11(cuenta): dtype:1 (CHAR), prc/scl:10/0, nullbl:0, octet:10, sign:1, radix:0
Exiting hgopcda, rc=0 at 2012/05/31-13:11:28
Entered hgopcda at 2012/05/31-13:11:28
Column:12(solar): dtype:2 (NUMERIC), prc/scl:5/0, nullbl:0, octet:10, sign:1, radix:0
Exiting hgopcda, rc=0 at 2012/05/31-13:11:28
Entered hgopcda at 2012/05/31-13:11:28
Column:13(construido): dtype:2 (NUMERIC), prc/scl:5/0, nullbl:0, octet:10, sign:1, radix:0
Exiting hgopcda, rc=0 at 2012/05/31-13:11:28
Entered hgopoer at 2012/05/31-13:11:28
hgopoer, line 233: got native error 0 and sqlstate HY091; message follows...
[Microsoft][ODBC Visual FoxPro Driver]Descriptor type out of range {HY091}
Exiting hgopoer, rc=0 at 2012/05/31-13:11:28
hgodscr, line 615: calling SQLColAttribute got sqlstate HY091
Entered hgopcda at 2012/05/31-13:11:28
Column:14(domicen): dtype:1 (CHAR), prc/scl:40/0, nullbl:0, octet:40, sign:1, radix:0
Exiting hgopcda, rc=0 at 2012/05/31-13:11:28
Entered hgopoer at 2012/05/31-13:11:28
hgopoer, line 233: got native error 0 and sqlstate HY091; message follows...
[Microsoft][ODBC Visual FoxPro Driver]Descriptor type out of range {HY091}
Exiting hgopoer, rc=0 at 2012/05/31-13:11:28
hgodscr, line 615: calling SQLColAttribute got sqlstate HY091
Entered hgopcda at 2012/05/31-13:11:28
Column:15(telef): dtype:1 (CHAR), prc/scl:11/0, nullbl:0, octet:11, sign:1, radix:0
Exiting hgopcda, rc=0 at 2012/05/31-13:11:28
Entered hgopoer at 2012/05/31-13:11:28
hgopoer, line 233: got native error 0 and sqlstate HY091; message follows...
[Microsoft][ODBC Visual FoxPro Driver]Descriptor type out of range {HY091}
Exiting hgopoer, rc=0 at 2012/05/31-13:11:28
hgodscr, line 615: calling SQLColAttribute got sqlstate HY091
Entered hgopcda at 2012/05/31-13:11:28
Column:16(fax): dtype:1 (CHAR), prc/scl:11/0, nullbl:0, octet:11, sign:1, radix:0
Exiting hgopcda, rc=0 at 2012/05/31-13:11:28
Entered hgopoer at 2012/05/31-13:11:28
hgopoer, line 233: got native error 0 and sqlstate HY091; message follows...
[Microsoft][ODBC Visual FoxPro Driver]Descriptor type out of range {HY091}
Exiting hgopoer, rc=0 at 2012/05/31-13:11:28
hgodscr, line 615: calling SQLColAttribute got sqlstate HY091
Entered hgopcda at 2012/05/31-13:11:28
Column:17(cif): dtype:1 (CHAR), prc/scl:11/0, nullbl:0, octet:11, sign:1, radix:0
Exiting hgopcda, rc=0 at 2012/05/31-13:11:28
Entered hgopoer at 2012/05/31-13:11:28
hgopoer, line 233: got native error 0 and sqlstate HY091; message follows...
[Microsoft][ODBC Visual FoxPro Driver]Descriptor type out of range {HY091}
Exiting hgopoer, rc=0 at 2012/05/31-13:11:28
hgodscr, line 615: calling SQLColAttribute got sqlstate HY091
Entered hgopcda at 2012/05/31-13:11:28
Column:18(litloc): dtype:1 (CHAR), prc/scl:30/0, nullbl:0, octet:30, sign:1, radix:0
Exiting hgopcda, rc=0 at 2012/05/31-13:11:28
hgodscr, line 910: Printing hoada @ 023E983C
MAX:18, ACTUAL:18, BRC:100, WHT=5 (SELECT_LIST)
hoadaMOD bit-values found (0x200:TREAT_AS_CHAR)
DTY NULL-OK LEN MAXBUFLEN PR/SC CST IND MOD NAME
1 CHAR N 8 8 0/ 0 0 0 200 codcen
1 CHAR N 45 45 0/ 0 0 0 200 litcen
1 CHAR N 5 5 0/ 0 0 0 200 codpos
1 CHAR N 2 2 0/ 0 0 0 200 codprov
1 CHAR N 3 3 0/ 0 0 0 200 codmun
1 CHAR N 2 2 0/ 0 0 0 200 codecol
1 CHAR N 2 2 0/ 0 0 0 200 codesin
1 CHAR N 4 4 0/ 0 0 0 200 cb
1 CHAR N 4 4 0/ 0 0 0 200 cs
1 CHAR N 2 2 0/ 0 0 0 200 digitocon
1 CHAR N 10 10 0/ 0 0 0 200 cuenta
3 DECIMAL N 7 7 5/ 0 0 0 0 solar
3 DECIMAL N 7 7 5/ 0 0 0 0 construido
1 CHAR N 40 40 0/ 0 0 0 200 domicen
1 CHAR N 11 11 0/ 0 0 0 200 telef
1 CHAR N 11 11 0/ 0 0 0 200 fax
1 CHAR N 11 11 0/ 0 0 0 200 cif
1 CHAR N 30 30 0/ 0 0 0 200 litloc
Exiting hgodscr, rc=0 at 2012/05/31-13:11:28 with error ptr FILE:hgodscr.c LINE:615 ID:Transfer Octet Length
hostmstr: 2036506624: HOA After hoxdscr
hostmstr: 2036506624: RPC After SQL Bundling
hostmstr: 2036506624: RPC Before SQL Bundling
hostmstr: 2036506624: HOA Before hoxclse
Entered hgoclse, cursor id 1 at 2012/05/31-13:11:28
Exiting hgoclse, rc=0 at 2012/05/31-13:11:28
hostmstr: 2036506624: HOA After hoxclse
hostmstr: 2036506624: HOA Before hoadafr
Entered hgodafr, cursor id 1 at 2012/05/31-13:11:28
Free hoada @ 023E983C
Exiting hgodafr, rc=0 at 2012/05/31-13:11:28
hostmstr: 2036506624: HOA After hoadafr
hostmstr: 2036506624: HOA Before hoxpars
Entered hgopars, cursor id 1 at 2012/05/31-13:11:28
type:0
SQL text from hgopars, id=1, len=235 ...
00: 53454C45 43542041 312E2263 6F646365 [SELECT A1."codce]
10: 6E222C41 312E226C 69746365 6E222C41 [n",A1."litcen",A]
20: 312E2263 6F64706F 73222C41 312E2263 [1."codpos",A1."c]
30: 6F647072 6F76222C 41312E22 636F646D [odprov",A1."codm]
40: 756E222C 41312E22 636F6465 636F6C22 [un",A1."codecol"]
50: 2C41312E 22636F64 6573696E 222C4131 [,A1."codesin",A1]
60: 2E226362 222C4131 2E226373 222C4131 [."cb",A1."cs",A1]
70: 2E226469 6769746F 636F6E22 2C41312E [."digitocon",A1.]
80: 22637565 6E746122 2C41312E 22736F6C ["cuenta",A1."sol]
90: 6172222C 41312E22 636F6E73 74727569 [ar",A1."construi]
A0: 646F222C 41312E22 646F6D69 63656E22 [do",A1."domicen"]
B0: 2C41312E 2274656C 6566222C 41312E22 [,A1."telef",A1."]
C0: 66617822 2C41312E 22636966 222C4131 [fax",A1."cif",A1]
D0: 2E226C69 746C6F63 22204652 4F4D2022 [."litloc" FROM "]
E0: 43454E54 524F5322 204131 [CENTROS" A1]
Entered hgopoer at 2012/05/31-13:11:28
hgopoer, line 233: got native error 200 and sqlstate 42000; message follows...
[Microsoft][ODBC Visual FoxPro Driver]Syntax error. {42000,NativeErr = 200}
Exiting hgopoer, rc=0 at 2012/05/31-13:11:28
hgopars, line 457: calling SQLPrepare got sqlstate 42000
Exiting hgopars, rc=28500 at 2012/05/31-13:11:28 with error ptr FILE:hgopars.c LINE:487 ID:Prepare stmt
hostmstr: 2036506624: HOA After hoxpars
hostmstr: 2036506624: RPC After SQL BundlingThe first issue I see is that Oracle 10.2.0.1 was never certified with DG4ODBC 11. Only 10.2.0.4 or 10.2.0.5 can be used as the Oracle database HS kernel requires a gateway compatibility patch and this patch is included in 10.2.0.4 or 10.2.0.5 Oracle database patch set.
Then another error in the trace is that for each column description you have an error:
hgopoer, line 233: got native error 0 and sqlstate HY091; message follows...
[Microsoft][ODBC Visual FoxPro Driver]*Descriptor type out of range* {HY091}
Exiting hgopoer, rc=0 at 2012/05/31-13:11:28
hgodscr, line 615: calling SQLColAttribute got sqlstate HY091
It seems it is not critical as DG4ODBC continues, but a more detailed analysis would require an ODBC trace.
When looking at the table description it seems the column names are all in lower letters, for example: solar. So commonly Dg4ODBC needs to quote the names
00: 53454C45 43542041 312E2263 6F646365 [SELECT A1."codce]
10: 6E222C41 312E226C 69746365 6E222C41 [n",A1."litcen",A]
20: 312E2263 6F64706F 73222C41 312E2263 [1."codpos",A1."c]
30: 6F647072 6F76222C 41312E22 636F646D [odprov",A1."codm]
40: 756E222C 41312E22 636F6465 636F6C22 [un",A1."codecol"]
50: 2C41312E 22636F64 6573696E 222C4131 [,A1."codesin",A1]
60: 2E226362 222C4131 2E226373 222C4131 [."cb",A1."cs",A1]
70: 2E226469 6769746F 636F6E22 2C41312E [."digitocon",A1.]
80: 22637565 6E746122 2C41312E 22736F6C ["cuenta",A1."sol]
90: 6172222C 41312E22 636F6E73 74727569 [ar",A1."construi]
A0: 646F222C 41312E22 646F6D69 63656E22 [do",A1."domicen"]
B0: 2C41312E 2274656C 6566222C 41312E22 [,A1."telef",A1."]
C0: 66617822 2C41312E 22636966 222C4131 [fax",A1."cif",A1]
D0: 2E226C69 746C6F63 22204652 4F4D2022 [."litloc" FROM "]
E0: 43454E54 524F5322 204131 [CENTROS" A1]
and according to the trace the FoxPro ODBC driver doesn't like these quotes and reports a syntax error.
So this explains at least why select codcen from centros@fox1 will fail. In general the Oracle database is case insensitive and translates all object names to upper case and the select it will pass to the foreign database would be similar to:
select CODCEN from CENTROS => which will fail as FoxPro is case sensitive. So the error message ORA-00904 (missing column name) is correct and the statement you need to use is:
select "codcen" from centros@fox1;
But this might lead again to the Syntax error you got earlier => You need to check which sign (single quote, back tick, double quote) Foxpro uses to quote object names and then set the gateway parameter HS_FDS_QUOTE_IDENTIFIER accordingly.
To check which character can be used to quote column/table names you might use the Microsoft ODBc test utility which was distributed in the old MDAC 2.8:
http://www.microsoft.com/downloads/details.aspx?familyid=5067faf8-0db4-429a-b502-de4329c8c850&displaylang=en
Edited by: kgronau on Jun 1, 2012 7:27 AM
If you know where I can download the MS FoxPro ODBC driver, please let me know and I'll check. -
Gateway for informix: Unsupported Informix Server and other errors
I set up the Database Gateway for Informix on WinXP 32 to connect from an Oracel 10gR2 Database to an Informix Database (Infomix Online Dynamic Server V7.31UP1).
The basic connection seems to work (giving a wrong password in the database link results in an appropriate error message), but the test-statement "select * from DUAL@DLTEST" (and any other select) results in the following error message:
>>>>>>>>>>>>>>>>>
ORA-28500: connection from ORACLE to a non-Oracle system returned this message:
[Oracle][ODBC Informix Wire Protocol driver]Unsupported Informix Server
version.[Oracle][ODBC Informix Wire Protocol driver]Invalid attribute in
connection string: ArraySize.[Oracle][ODBC Informix Wire Protocol
driver]Invalid attribute in connection string: TruncateOversizedColumnValues.
ORA-02063: preceding 2 lines from DLTEST
<<<<<<<<<<<<<<<<<
Setting HS_FDS_TRACE_LEVEL=DEBUG gives the following trace-output in <oracle_home>\dg4ifmx\trace\dg4ifmx_agt_2716.trc:
>>>>>>>>>>>>>>>>>>>
Oracle Corporation --- MONTAG JUN 09 2008 13:59:13.671
Heterogeneous Agent Release
11.1.0.6.0
Oracle Corporation --- MONTAG JUN 09 2008 13:59:13.671
Version 11.1.0.6.0
Entered hgogprd
HOSGIP for "HS_FDS_TRACE_LEVEL" returned "DEBUG"
Entered hgosdip
setting HS_OPEN_CURSORS to default of 50
HOSGIP returned value of "straf" for HS_FDS_RECOVERY_ACCOUNT
HOSGIP returned a value for HS_FDS_RECOVERY_PWD
setting HS_FDS_TRANSACTION_LOG to default of "HS_TRANSACTION_LOG"
setting HS_FDS_TRANSACTION_ISOLATION to default of "READ_COMMITTED"
setting HS_NLS_NCHAR to default of "AL16UTF16"
setting HS_FDS_TIMESTAMP_AS_DATE to default of "TRUE"
setting HS_RPC_FETCH_REBLOCKING to default of "ON"
setting HS_FDS_FETCH_ROWS to default of "100"
setting HS_FDS_RESULTSET_SUPPORT to default of "FALSE"
setting HS_FDS_PROC_IS_FUNC to default of "FALSE"
setting HS_FDS_CHARACTER_SEMANTICS to default of "FALSE"
setting HS_FDS_MAP_NCHAR to default of "TRUE"
setting HS_NLS_DATE_FORMAT to default of "YYYY-MM-DD HH24:MI:SS"
setting HS_FDS_REPORT_REAL_AS_DOUBLE to default of "FALSE"
setting HS_LONG_PIECE_TRANSFER_SIZE to default of "65536"
setting HS_SQL_HANDLE_STMT_REUSE to default of "FALSE"
setting HS_FDS_QUERY_DRIVER to default of "FALSE"
setting HS_CALL_NAME_ISP to "gtw$:SQLTables;gtw$:SQLColumns;gtw$:SQLPrimaryKeys;gtw$:SQLForeignKeys;gtw$:SQLProcedures;gtw$:SQLStatistics"
Exiting hgosdip, rc=0
ORACLE_SID is "dg4ifmx"
Product-Info:
Port Rls/Upd:6/0 PrdStat:0
Agent:Oracle Database Gateway for INFORMIX
Facility:hsa
Class:IFMX, ClassVsn:11.1.0.6.0_0006, Instance:dg4ifmx
Exiting hgogprd, rc=0
Entered hgoinit
HOCXU_COMP_CSET=1
HOCXU_DRV_CSET=178
HOCXU_DRV_NCHAR=2000
HOCXU_DB_CSET=46
HOCXU_SEM_VER=100000
Entered hgolofn at 2008/06/09-13:59:14
RC=-1 from HOSGIP for "PATH"
PATH from environment is "D:\oracle_11g\bin;C:\WINDOWS\system32;C:\WINDOWS;C:\WINDOWS\System32\Wbem;D:\Programme\jdk1.4\bin;d:\programme\GTK\2.0\bin;"D:\Programme\Hummingbird\Connectivity\7.00\Accessories\";d:\Tools\GTK_2.0\bin;d:\tools\IsoBuster"
Exiting hgolofn, rc=0 at 2008/06/09-13:59:14
HOSGIP for "HS_OPEN_CURSORS" returned "50"
HOSGIP for "HS_FDS_FETCH_ROWS" returned "100"
HOSGIP for "HS_LONG_PIECE_TRANSFER_SIZE" returned "65536"
HOSGIP for "HS_NLS_NUMERIC_CHARACTER" returned ".,"
Exiting hgoinit, rc=0 at 2008/06/09-13:59:14
Entered hgolgon at 2008/06/09-13:59:14
reco:0, name:straf, tflag:0
Entered hgosuec at 2008/06/09-13:59:14
uencoding=UTF16
Entered shgosuec at 2008/06/09-13:59:14
Exiting shgosuec, rc=0 at 2008/06/09-13:59:14
shgosuec() returned rc=0
Exiting hgosuec, rc=0 at 2008/06/09-13:59:14
HOSGIP for "HS_FDS_RECOVERY_ACCOUNT" returned "straf"
HOSGIP for "HS_FDS_TRANSACTION_LOG" returned ""HS_TRANSACTION_LOG""
HOSGIP for "HS_FDS_TIMESTAMP_AS_DATE" returned "TRUE"
HOSGIP for "HS_FDS_CHARACTER_SEMANTICS" returned "FALSE"
HOSGIP for "HS_FDS_MAP_NCHAR" returned "TRUE"
HOSGIP for "HS_FDS_RESULT_SET_SUPPORT" returned "FALSE"
HOSGIP for "HS_FDS_PROC_IS_FUNC" returned "FALSE"
HOSGIP for "HS_FDS_REPORT_REAL_AS_DOUBLE" returned "FALSE"
using straf as default value for "HS_FDS_DEFAULT_OWNER"
HOSGIP for "HS_SQL_HANDLE_STMT_REUSE" returned "FALSE"
Entered hgocont at 2008/06/09-13:59:15
HS_FDS_CONNECT_INFO = "sijus10000:22231/si10000onl/kwadbstr"
RC=-1 from HOSGIP for "HS_FDS_CONNECT_STRING"
Entered hgogenconstr at 2008/06/09-13:59:15
dsn:sijus10000:22231/si10000onl/kwadbstr, name:straf
optn:
Entered shgogohn at 2008/06/09-13:59:15
ohn is 'OraGtw11g'
Exiting shgogohn, rc=0 at 2008/06/09-13:59:15
Entered hgocont_OracleCsidToIANA at 2008/06/09-13:59:15
Returning 2252
Exiting hgocont_OracleCsidToIANA at 2008/06/09-13:59:15
##>Connect Parameters (len=299)<##
## DRIVER=Oracle 11g dg4ifmx-OraGtw11g;
## HostName=sijus10000;
## PortNumber=22231;
## ServerName=si10000onl;
## Database=kwadbstr;
#! UID=straf;
#! PWD=*
## ApplicationUsingThreads=1;
## CancelDetectInterval=0;
## TrimBlankFromIndexName=1;
## IANAAppCodePage=2252;
## ArraySize=100;
## UseDelimitedIdentifier=1;
## TruncateOversizedColumnValues=0;
Exiting hgogenconstr, rc=0 at 2008/06/09-13:59:15
Entered hgopoer at 2008/06/09-13:59:15
hgopoer, line 159: got native error 0 and sqlstate HY000; message follows...
[Oracle][ODBC Informix Wire Protocol driver]Unsupported Informix Server version.[Oracle][ODBC Informix Wire Protocol driver]Invalid attribute in connection string: ArraySize.[Oracle][ODBC Informix Wire Protocol driver]Invalid attribute in connection string: TruncateOversizedColumnValues.
Exiting hgopoer, rc=0 at 2008/06/09-13:59:15
hgocont, line 1890: calling SqlDriverConnect got sqlstate HY000
Exiting hgocont, rc=28500 at 2008/06/09-13:59:15 with error ptr FILE:hgocont.c LINE:1910 ID:Something other than invalid authorization
Exiting hgolgon, rc=28500 at 2008/06/09-13:59:15 with error ptr FILE:hgolgon.c LINE:612 ID:Calling hgocont
Entered hgoexit at 2008/06/09-13:59:15
Exiting hgoexit, rc=0 at 2008/06/09-13:59:15
<<<<<<<<<<<<<<<<<<<<<<<<
What's going wrong ?
Regards KlausHello,
I downloaded the gateway package of Oracle version 11.1.0.6.0, and installed Informix gateway driver. I made the necessary settings, and i have exactly the same problem, as described above.
I receive error message "OracleODBC Informix Wire Protocol driverUnsupported Informix Server version.OracleODBC Informix Wire Protocol driverInvalid attribute in connection string: ArraySize.OracleODBC Informix Wire Protocol driverInvalid attribute in connection string: TruncateOversizedColumnValues." when trying to set up a connection from Oracle to Informix 7.3. I read here, that there is a patch of Informix gateway: fix 6799360, which is unfortunately not available for for download for Windows XP. I cannot search MetaLink for this problem, because I just would like to test this Oracle feature, I did not buy Oracle license.
Does anybody know about this patch? Can anybody help how could I make working this Informix gateway?
Thanks for help, Gyula -
Problem with "Database Gateway for SQL Server"
Hello,
i am testing the different technologies for connecting an oracle database with a sql-server database.
The way using 10g-generic-connectivity with ODBC works fine, but the 11g-DG4MSQL makes problems.
Environment:
Server PEGASUS (32bit Windows Server 2003 R2 SP2) with Oracle Database 10g Release 10.2.0.4.0
Server OBELIXUS (32bit Windows 2000 Sp4) with MS-SQL-Server 2005
On PEGASUS i have installed the gateway in a new oracle home directory:
"D:\oracle\product\10.2.0\db_1" => home directory of 10g
"D:\oracle\product\11.1.0\tg_1\" => home directory of the gateway
D:\oracle\product\10.2.0\db_1\NETWORK\ADMIN\tnsnames.ora:
MSSQLDG =
(DESCRIPTION =
(ADDRESS_LIST =
(ADDRESS = (PROTOCOL = TCP)(HOST = PEGASUS)(PORT = 1521))
(CONNECT_DATA =
(SERVICE_NAME = DG4MSQL)
(HS = OK)
MSSQL =
(DESCRIPTION =
(ADDRESS_LIST =
(ADDRESS = (PROTOCOL = TCP)(HOST = PEGASUS)(PORT = 1521))
(CONNECT_DATA =
(SERVICE_NAME = MSSQLTEST)
(HS = OK)
D:\oracle\product\10.2.0\db_1\NETWORK\ADMIN\listener.ora:
SID_LIST_LISTENER =
(SID_LIST =
(SID_DESC =
(SID_NAME = PLSExtProc)
(ORACLE_HOME = D:\oracle\product\10.2.0\db_1)
(PROGRAM = extproc)
(SID_DESC =
(GLOBAL_DBNAME = INTEGRAT)
(ORACLE_HOME = D:\oracle\product\10.2.0\db_1)
(SID_NAME = INTEGRAT)
(SID_DESC =
(SID_NAME = MSSQLTEST)
(PROGRAM = D:\oracle\product\10.2.0\db_1\bin\hsodbc)
(ORACLE_HOME = D:\oracle\product\10.2.0\db_1)
(SID_DESC=
(SID_NAME=DG4MSQL)
(ORACLE_HOME=D:\oracle\product\11.1.0\tg_1)
(PROGRAM=D:\oracle\product\11.1.0\tg_1\BIN\dg4msql)
LISTENER =
(DESCRIPTION_LIST =
(DESCRIPTION =
(ADDRESS = (PROTOCOL = IPC)(KEY = EXTPROC1))
(ADDRESS = (PROTOCOL = TCP)(HOST = pegasus.cursor.de)(PORT = 1521))
D:\oracle\product\11.1.0\tg_1\dg4msql\admin\initDG4MSQL.ora:
HS_FDS_CONNECT_INFO=OBELIXUS/MSSQLSERVER/testuju
HS_FDS_TRACE_LEVEL=DEBUG
HS_FDS_RECOVERY_ACCOUNT=RECOVER
HS_FDS_RECOVERY_PWD=RECOVER
D:\oracle\product\10.2.0\db_1\hs\admin\initMSSQLTEST.ora:
HS_FDS_CONNECT_INFO=DSN_MSSQL
HS_FDS_TRACE_LEVEL=OFF
HS_LANGUAGE=AMERICAN_AMERICA.WE8MSWIN1252
HS_FDS_FETCH_ROWS=100
HS_RPC_FETCH_REBLOCKING=OFF
How mentioned above, the access from oracle to sqlserver using MSSQL(10g hsodbc.exe) works fine.
But when trying to acces the sqlserver using MSSQLDG (11g dg4msql.exe) I get the following error:
ORA-28500: Verbindung von ORACLE zu Fremdsystem gab diese Nachricht zurück:
[Oracle][ODBC SQL Server Driver][DBNETLIB]Ungültige Verbindung.
[Oracle][ODBC SQL Server Driver][DBNETLIB]ConnectionOpen (ParseConnectParams()).
[Oracle][ODBC SQL Server Driver]Ungültiges Attribut für die Verbindungszeichenfolge
ORA-02063: vorherige 2 lines von DBL_MSSQL4
Here the contect of the file "DG4MSQL_agt_2332.trc":
Oracle Corporation --- FREITAG AUG 22 2008 16:17:42.198
Heterogeneous Agent Release
11.1.0.6.0
Oracle Corporation --- FREITAG AUG 22 2008 16:17:42.198
Version 11.1.0.6.0
Entered hgogprd
HOSGIP for "HS_FDS_TRACE_LEVEL" returned "DEBUG"
Entered hgosdip
setting HS_OPEN_CURSORS to default of 50
HOSGIP returned value of "RECOVER" for HS_FDS_RECOVERY_ACCOUNT
HOSGIP returned a value for HS_FDS_RECOVERY_PWD
setting HS_FDS_TRANSACTION_LOG to default of "HS_TRANSACTION_LOG"
setting HS_FDS_TRANSACTION_ISOLATION to default of "READ_COMMITTED"
setting HS_NLS_NCHAR to default of "AL16UTF16"
setting HS_FDS_TIMESTAMP_AS_DATE to default of "TRUE"
setting HS_RPC_FETCH_REBLOCKING to default of "ON"
setting HS_FDS_FETCH_ROWS to default of "100"
setting HS_FDS_RESULTSET_SUPPORT to default of "FALSE"
setting HS_FDS_PROC_IS_FUNC to default of "FALSE"
setting HS_FDS_CHARACTER_SEMANTICS to default of "FALSE"
setting HS_FDS_MAP_NCHAR to default of "TRUE"
setting HS_NLS_DATE_FORMAT to default of "YYYY-MM-DD HH24:MI:SS"
setting HS_FDS_REPORT_REAL_AS_DOUBLE to default of "FALSE"
setting HS_LONG_PIECE_TRANSFER_SIZE to default of "65536"
setting HS_SQL_HANDLE_STMT_REUSE to default of "FALSE"
setting HS_FDS_QUERY_DRIVER to default of "FALSE"
setting HS_CALL_NAME_ISP to "gtw$:SQLTables;gtw$:SQLColumns;gtw$:SQLPrimaryKeys;gtw$:SQLForeignKeys;gtw$:SQLProcedures;gtw$:SQLStatistics"
Exiting hgosdip, rc=0
ORACLE_SID is "DG4MSQL"
Product-Info:
Port Rls/Upd:6/0 PrdStat:0
Agent:Oracle Database Gateway for MSSQL
Facility:hsa
Class:MSSQL, ClassVsn:11.1.0.6.0_0006, Instance:DG4MSQL
Exiting hgogprd, rc=0
Entered hgoinit
HOCXU_COMP_CSET=1
HOCXU_DRV_CSET=178
HOCXU_DRV_NCHAR=2000
HOCXU_DB_CSET=178
HOCXU_SEM_VER=102000
Entered hgolofn at 2008/08/22-16:17:42
RC=-1 from HOSGIP for "PATH"
PATH from environment is "d:\oracle\product\11.1.0\tg_1\bin;D:\oracle\product\10.2.0\db_1\bin;C:\WINDOWS\system32;C:\WINDOWS;C:\WINDOWS\System32\Wbem;C:\Programme\IBM\Informix\Client-SDK\bin"
Exiting hgolofn, rc=0 at 2008/08/22-16:17:43
HOSGIP for "HS_OPEN_CURSORS" returned "50"
HOSGIP for "HS_FDS_FETCH_ROWS" returned "100"
HOSGIP for "HS_LONG_PIECE_TRANSFER_SIZE" returned "65536"
HOSGIP for "HS_NLS_NUMERIC_CHARACTER" returned ".,"
Exiting hgoinit, rc=0 at 2008/08/22-16:17:43
Entered hgolgon at 2008/08/22-16:17:43
reco:0, name:testuju, tflag:0
Entered hgosuec at 2008/08/22-16:17:43
uencoding=UTF16
Entered shgosuec at 2008/08/22-16:17:43
Exiting shgosuec, rc=0 at 2008/08/22-16:17:43
shgosuec() returned rc=0
Exiting hgosuec, rc=0 at 2008/08/22-16:17:43
HOSGIP for "HS_FDS_RECOVERY_ACCOUNT" returned "RECOVER"
HOSGIP for "HS_FDS_TRANSACTION_LOG" returned ""HS_TRANSACTION_LOG""
HOSGIP for "HS_FDS_TIMESTAMP_AS_DATE" returned "TRUE"
HOSGIP for "HS_FDS_CHARACTER_SEMANTICS" returned "FALSE"
HOSGIP for "HS_FDS_MAP_NCHAR" returned "TRUE"
HOSGIP for "HS_FDS_RESULT_SET_SUPPORT" returned "FALSE"
HOSGIP for "HS_FDS_PROC_IS_FUNC" returned "FALSE"
HOSGIP for "HS_FDS_REPORT_REAL_AS_DOUBLE" returned "FALSE"
using testuju as default value for "HS_FDS_DEFAULT_OWNER"
HOSGIP for "HS_SQL_HANDLE_STMT_REUSE" returned "FALSE"
Entered hgocont at 2008/08/22-16:17:43
HS_FDS_CONNECT_INFO = "OBELIXUS/MSSQLSERVER/testuju"
RC=-1 from HOSGIP for "HS_FDS_CONNECT_STRING"
Entered hgogenconstr at 2008/08/22-16:17:43
dsn:OBELIXUS/MSSQLSERVER/testuju, name:testuju
optn:
Entered shgogohn at 2008/08/22-16:17:43
ohn is 'OraGtw11g_home1'
Exiting shgogohn, rc=0 at 2008/08/22-16:17:43
Entered hgocont_OracleCsidToIANA at 2008/08/22-16:17:43
Returning 2252
Exiting hgocont_OracleCsidToIANA at 2008/08/22-16:17:43
##>Connect Parameters (len=223)<##
## DRIVER=Oracle 11g dg4msql-OraGtw11g_home1;
## SERVER=OBELIXUS\MSSQLSERVER;
## Database=testuju;
#! UID=testuju;
#! PWD=*
## AnsiNPW=Yes;
## QuotedId=Yes;
## IANAAppCodePage=2252;
## ArraySize=100;
## PadVarbinary=0;
## SupportNumericPrecisionGreaterThan38=1;
Exiting hgogenconstr, rc=0 at 2008/08/22-16:17:44
Entered hgopoer at 2008/08/22-16:18:00
hgopoer, line 159: got native error 14 and sqlstate 08001; message follows...
[Oracle][ODBC SQL Server Driver][DBNETLIB]Ungültige Verbindung.[Oracle][ODBC SQL Server Driver][DBNETLIB]ConnectionOpen (ParseConnectParams()).[Oracle][ODBC SQL Server Driver]Ungültiges Attribut für die Verbindungszeichenfolge
Exiting hgopoer, rc=0 at 2008/08/22-16:18:00
hgocont, line 1890: calling SqlDriverConnect got sqlstate 08001
Exiting hgocont, rc=28500 at 2008/08/22-16:18:00 with error ptr FILE:hgocont.c LINE:1910 ID:Something other than invalid authorization
Exiting hgolgon, rc=28500 at 2008/08/22-16:18:00 with error ptr FILE:hgolgon.c LINE:612 ID:Calling hgocont
Entered hgoexit at 2008/08/22-16:18:00
Exiting hgoexit, rc=0 at 2008/08/22-16:18:00
Many thanks in advance for any help!
Regards HartmutAt first your configuration is not really correct.
=====================================================
In the LISTENER.ORA from 10g, you must only refer to the database and hsodbc 10g
D:\oracle\product\10.2.0\db_1\NETWORK\ADMIN\listener.ora:
SID_LIST_LISTENER =
(SID_LIST =
(SID_DESC =
(SID_NAME = PLSExtProc)
(ORACLE_HOME = D:\oracle\product\10.2.0\db_1)
(PROGRAM = extproc)
(SID_DESC =
(GLOBAL_DBNAME = INTEGRAT)
(ORACLE_HOME = D:\oracle\product\10.2.0\db_1)
(SID_NAME = INTEGRAT)
(SID_DESC =
(SID_NAME = MSSQLTEST)
(PROGRAM = D:\oracle\product\10.2.0\db_1\bin\hsodbc)
(ORACLE_HOME = D:\oracle\product\10.2.0\db_1)
LISTENER =
(DESCRIPTION_LIST =
(DESCRIPTION =
(ADDRESS = (PROTOCOL = IPC)(KEY = EXTPROC1))
(ADDRESS = (PROTOCOL = TCP)(HOST = pegasus.cursor.de)(PORT = 1521))
===========================================================
Then you have to create a new listener (new name) in the gateway oracle_home on a different port than instance database:
D:\oracle\product\11.1.0\tg_1\network\admin\listener.ora
SID_LIST_LISTENERGTW =
(SID_LIST =
(SID_DESC=
(SID_NAME=DG4MSQL)
(ORACLE_HOME=D:\oracle\product\11.1.0\tg_1)
(PROGRAM=D:\oracle\product\11.1.0\tg_1\BIN\dg4msql)
LISTENERGTW=
(DESCRIPTION_LIST =
(DESCRIPTION =
(ADDRESS = (PROTOCOL = TCP)(HOST = pegasus.cursor.de)(PORT = 1522))
To start it, use the command below:
D:\oracle\product\11.1.0\tg_1\bin\LSNRCTL start listenergtw
===========================================================
D:\oracle\product\10.2.0\db_1\NETWORK\ADMIN\tnsnames.ora:
match the DG4MSQL with the listener on 1522 port
HSODBC match with binary10g on listener 1521 port
MSSQLDG =
(DESCRIPTION =
(ADDRESS = (PROTOCOL = TCP)(HOST = PEGASUS)(PORT = 1522))
(CONNECT_DATA =(SERVICE_NAME = DG4MSQL))
(HS = OK)
MSSQL =
(DESCRIPTION =
(ADDRESS = (PROTOCOL = TCP)(HOST = PEGASUS)(PORT = 1521))
(CONNECT_DATA =(SERVICE_NAME = MSSQLTEST))
(HS = OK)
Try to configure and let me know your feedback
regards,
Mireille -
Max IPs in a DHCP range for Roaming network?
Setting up an AirPort roaming network comprised of a dozen or so AirPort-Extremes all connected via a Fast Ethernet backbone.
The Master base station has a Public IP on it's WAN side and is Set to 'Share a Public IP address' and DHCP - but it seems no matter which network prefix I choose for the LAN side, I can not create a DHCP range larger than a single Class C. Is there a way to give out more than 254 IPs? Or can you have a single roaming network with multiple base stations set to DHCP?Is there a way to give out more than 254 IPs?
No, as the "main" router, providing DHCP server service is the limiting factor here.
Or can you have a single roaming network with multiple base stations set to DHCP?
This may be possible, but NOT with the Apple routers. When configured as bridges, as required for a roaming network, both their NAT & DHCP services are disabled. -
Invalid column name for Transparent Gateway for SQLServer
I have successfully set up a transparent gateway for an MS SQLServer database 'pubs' from Oracle 910. I am able to run the following statement successfully as it returns all results without a hitch:
select * from authors@pubs;
pubs is the database link for the transparent gateway.
But when I select any particular column in the select statement like:
select city from authors@pubs;
I get the following error:
select city from authors@pubs
ERROR at line 1:
ORA-00904: invalid column name
Can anyone help me with this?
ThanksSamarjit,
This should work. Are you using a certified configuration?
Check our certification matrix at http://otn.oracle.com/products/gateways/pdf/certmatrix2.pdf
Vira -
Gateway for Sybase or MS SQL - support for Timestamp
Hi All,
Is there any way to get Timestamp data out of Sybase or MS SQL Server?
I thought this would be pretty straightforward, but after a short investigation I'm no longer that optimistic...
The "Database Gateway for Sybase User's Guide" says in Appendix A, that the following conversions are performed by the gateway:
(Sybase - Oracle)
DATE - DATE
DATETIME - DATE
SMALLDATETIME - DATE
TIMESTAMP - RAW
TIME - CHAR(15)
It says the same for MS SQL Server.
What I need is a conversion from Sybase DATETIME into Oracle TIMESTAMP, but I'm guessing there is a limitation of the Gateway
and it is not able to use the millisecond data in any way... Am I right?
Or maybe there is some magic setting in the .ini file for this? Things like HS_NLS_TIMESTAMP_FORMAT seem to be unsupported by Sybase gateway.
I'm using 11.2.0.1 on Linux.
Thanks for any hints.Hi,
As you have seen in the documentation the Sybase and SQL*Server datatime columns are translated as Oracle DATE datatypes, so the milisecond data will be lost.
the 11.2 DG4MSQL Users Guide actually says -
SQL*Server Oracle Comment
DATETIME DATE Fractional parts of a second are truncated
although the Dg4Sybase Users Guide has the same conversion it does not have the comment.
The only way round it would be use a different non-Oracle datatyp from which you could extract the millesecond part of the string.
Regards,
Mike -
How to configure distributed transaction in Oracle Database Gateway for ODBC? (ORA-02047)
I am connecting from Oracle to another database server (MS SQL Server, DB2 the error message is the same) through an ODBC connection using Oracle SQL Developer. (This is how I set up)
I want to query the schema of a non-Oracle database using the data dictionary mapping of the Oracle Database Gateway for ODBC.
This works well:
select * from all_tables@katimssql;
But this doesn't:
create table alltables_mssql as
select * from all_tables@katimssql;
Output:
Error report:
SQL Error: ORA-00604: error occurred at recursive SQL level 1
ORA-02047: cannot join the distributed transaction in progress
ORA-06512: at "SYS.HS$_DDTF_SQLTABLES", line 58
ORA-06512: at line 1
Does anyone know the solution of this?
Thanks in advance,
Kata
Details:
Oracle Database 11g Express Edition Release 11.2.0.2.0
Microsoft SQL Server 2008 (SP2) - 10.0.4000.0 (X64)
ODBC Driver: SQL Server Native Client 11.0 (32 bit)
initkatimssql.ora:
HS_FDS_CONNECT_INFO=katimssql
HS_FDS_TRACE_LEVEL = ON
HS_TRANSACTION_MODEL = READ_ONLY_AUTOCOMMIT
I tried these, none of them worked, the error message is the same.
HS_FDS_TRACE_LEVEL = off
HS_TRANSACTION_MODEL = SINGLE_SITE
HS_TRANSACTION_MODEL = READ_ONLY_AUTOCOMMIT
HS_TRANSACTION_MODEL = READ_ONLYHi Kata,
this won't work as the ALL_TABLES is not a table that exists in your SQl Server - instead it is a "mimicked" table. This means the gateway will check if you have on your SQL Server a table called all_tables and when there's no table it will start an internal mechanism to check out what sort of tables exist in your SQL Server database. So the gateway is starting internally another transaction to get details from the foreign database and DG4ODBC can't participate in distributed transactions at all. Instead of using all_tables you have to use a real SQL Server table like SQ Server sys.objects or sys.tables.
- Klaus -
Oracle Transparent Gateway for MS SQL Server
Hello,
I successfully installed the Oracle transparent Gateway for MS SQL Server for Oracle 8i. Now I am doing the same for Oracle 9i.
Does anyone know how to 'create a new gateway service' on 9i???
This is how you would do that on 8i on the Windows box...
1) At the MS-DOS prompt, enter:
> set GTW_EXE=TG4MSQL.EXE
2) To create a new gateway service name, enter:
> GTWSRV73 sid -CREATE | MORE
-where sid is the gateway sid.
Does anyone know how to do those steps for 9i Oracle Transparent Gateway?
Thank you.Hi
I need oracle Tranparent Gateway for Microsoft Sqlserver (tg4msql) for oracle 10g on linux x86-64 bit. I have searched for it on otn.oracle.com and on edelivery.oracle.com. But couldn't find it.
Can any one help me in this regard.
Regards
Nadir.
Maybe you are looking for
-
How to dinamically name objects in a for statement using addChild
Hi. I was wondering where did go the for statement with attachMovie from library in AS 3. I mean i was having in AS 2: for (i=0; i<5; i++) { attachMovie("sim", "sim"+i, i); Now in AS 3: for (var i=0; i<5; i++) { addChild(new sim()); I can't figure ou
-
Condition Records not to be calculated if base value is negative
Dear all I have configured a pricing procedure which is being used while performing DP90 with reference to service order. Now the values are getting populated in condition type EK02 and based on this value various other charges like service tax, supe
-
Ive been told to rebuild my site, should I use Muse or Dreamweaver?
Hi everyone, Just recently I had someone perform an audit on my website and the results that came back weren't good. It seems I have all sorts of problems with my site, mainly from an SEO perspective. The guys that did the audit said they could rebui
-
Correct black screen in apps on iPad mini?
After upgrading to iOS 7 on my iPad mini2 I am seeing a black screen locking access to an app. How can I correct it, the app is Words with friends.
-
Photoshop CS6 Cloud 13.1.1 32-bit & 64-bit keeps asking to licence software at start twice
Photoshop CS6 Cloud 13.1.1 32-bit & 64-bit keeps asking to licence software at start twice. Once when i start it and again once I sign in? I recently refreshed the host file in windows to see if helped but not. Regards James Howarth