Set-up of RE4100W with X3500 gateway

I just purchased a RE4100W range extender and want to set this up with my x3500 gateway.
I am using a MAC filter in my Gateway, hence I have configured the extender device , the 5ghz and 2 ghz MAC adresses in my gateway. I have set up the extender with auto DHCP and not a fixed IP in my network.
Allthough i can see that the extender is sending the strong signal, somehow it does not connect to my network... it comes with a message that my AP setting have changed , and even asks for a username and password from the gateway? This despite a complete reconfiguration of the gateway...
I am starting to wonder if there is a compatability problem between the 2 devices... Maybe firmware software versions ? etc...
Grateful for some one to advise any next steps I can take...
regards
Rene

Try to reset your range extender and setup the unit manually instead. To do this, you may follow the instructions and other workarounds from this link: http://kb.linksys.com/Linksys/ukp.aspx?pid=80&vw=1&articleid=25153 . By the way, having a range extender in between the setup defeats the purpose of enabling MAC filter in your gateway.

Similar Messages

Steps to set up my domain with Apache

Hello,
I would like to know the steps to set up my domain with Apache including the use of DNS Services. I have DNS services (http://www.dnsexit.com) . I just don't know where to begin with it adding my domain. I've already went to my preferences>>sharing>> web sharing and turned it on. My domain host is netfirms. I have an actiontec model- m1424-wr router and I have a verizon fios wireless connection that's always on. I've been doing my research on this. I'm just stuck on this part. However is it true that php/mysql is pre-installed on Mac osx 10.6? I hope I can get help. Thank you in advance.

Your description is somewhat incomplete. I assume that dnsexit.com provides dynamic DNS and that you registered a domain name with NetFirms (you say "domain host", but I presume that you just registered the domain name and they aren't actually hosting it; hosting means that your web site is on their computers instead of yours). I'll also assume that you mean that you intend to run a web server on your Mac through your FiOS connection (not a great idea, and potentially a violation of FiOS' terms of service unless you bought their commercial plan).
If all of those assumptions are correct, you need to:
1. Contact NetFirms and tell them to point your domain to DNSExit's name servers: ns1.dnsExit.com and ns2.dnsExit.com and ns3.dnsExit.com and ns4.dnsExit.com
2. After step 1 is complete, you need to install a dynamic DNS update client on a computer in your network that will always be on (DNSExit has them and installation and set-up instructions). These programs will periodically check the IP address of your network and, if it changes, will update the record at DNSExit so that sites can find it. Note that you are using FiOS so the IP address of your router is expected to change periodically; this works around that. Your router has 2 IP addresses: the WAN is the IP address exposed to the world through your FiOS connect, and the LAN, which is an address local to your home network.
3. Login to your ActionTEC router as the adminsitrator. You can do this through your web browser. The LAN IP address of the router is the gateway address indicated in the Network preference pane for your ethernet connection. The modem documentation tells you the default password for the router (make sure to change it).
Perform the following tasks on the router (though the advanced options, you'll want to poke around to find them):
a. check the DHCP address ranges (usually it says that it will give out IP addresses from 192.168.1.100-192.168.1.200 or similar). Note it down. You're going to want to give the computer that acts as the web server a static IP address outside that range.
b. Choose an address outside the DHCP range that isn't already in use and write it down. This will be the static IP addres you will set on your web server.
c. Locate the Firewall/NAT settings on the router and add a rule to forward traffic on ports 80 and 443 to the IP address you had chosen.
4. On the computer that will be the web server, start web-sharing.
5. Go to the network preferences and configure the static IP address that you selected. Use the same gateways and DNS settings that were assigned by DHCP.
... and that's it. If you performed all those steps properly, requests to your domain will be sent to your FiOS modem and forwarded on to the designated computer for a response.
PHP and Apache are preinstalled on the Mac. MySQL is not. You will need to download and install MySQL yourself.

Cisco Clean Access OOB with virtual gateway

I have set the clean access OOB virtual gateway mode, i put managed subnet one of unused ip with unauthenticated vlan,some of the pc running with dhcp so i put ip refresh after successful authentication (this working fine), but some of them running with static so i cannot refresh the ip address,
after authentication through clean access clean access manager changing Unautheticated vlan(44) authenticated vlan (4), but i can't access internet and any other application through network (even with static ip and dhcp (if i put refresh dhcp ip i can) ), in pc arp cache i can see the orginal gateway mac address if i clear the arp cache with arp -d command the moment it start working how can solve this issue please help me guys
thank you

This document describes how to configure the syslog settings in order to log the events to an external server in the Cisco Network Admission Control (NAC) Appliance, formerly known as Cisco Clean Access (CA).
http://www.cisco.com/en/US/products/ps6128/products_tech_note09186a008085d6e9.shtml

Difference between setting up a vpn with windows 7 and cisco routers

Hi.I was wondering what the main difference Is between setting up a vpn with windows 7 or configuring It on cisco routers.
When you setup the vpn on windows 7 or xp do the client and server pc's take care of the encryption and decryption whereas configuring vpn on routers , the encryption and decryption Is done solely by the routers?
If I want to setup a connection where an IP In the same Internal lan Is assigned to the client pc I'm guessing I'd have to use a router configuration.
Thanks

Thank you for the response, lucky for me there was another option. Threatened to cancel with the ISP on the NAT side unless they assigned us a public static ip/gateway/subnet. They ended up doing that and the VPN connected as soon as the changes were made in the Linksys.

What is the criteria for a local network with RDS Gateway 2012?

I have a hard time finding out what the criteria are how RDS 2012 detemines that the network the client is on is a local network or an external one. I have one subnet within our network that isn't recognised as a local network and all RDS traffic is
passed to the gateway server. This is something we don't want for internal addresses. Can anyone enlighten me how RDS determines whether you are on an internal or external network?
Thanks!
Leo

Hi,
Thank you for posting in Windows Server Forum.
As per my research I can say that RDS when getting any connection it looks for DNS to verify as all the usage for internal\external entries is made under DNS for his environment through RD Gateway.
The RD Gateway role service provides secure access by establishing an SSL tunnel from the client to the RD Gateway. The RD Gateway acts as the middleman. It passes traffic to and from the client over port 443, and to and from the internal resource over port
3389. Any communication between the RD Gateway and the external client is also encrypted. The RD Gateway uses authorization policies to determine who can use the service and the specific resources to which they’re allowed access. You can configure different
permission sets for people depending on whether they’re connecting from within or outside the network.
You can get more details from beneath link.
How To Work with RD Gateway in Windows Server 2012
http://redmondmag.com/articles/2013/12/24/rd-gateway-in-windows-server.aspx
Hope it helps!
Thanks.
Dharmesh Solanki
TechNet Community Support
Please remember to mark the replies as answers if they help and unmark them if they provide no help. If you have feedback for TechNet Support, contact [email protected]

Questions about setting up my network with my Mac Pro?

I'm trying to set up my network with my Mac Pro. I have two other roommates that need internet and a printer that we all need to access. The modem is with my Mac Pro in room 1, the printer is with another PC in room 2, and another PC with wifi is in room 3. What is the best way to connect all these.
My idea was to install an Airport card in my Mac Pro, then add an Airport Express station w/airtunes to room 2, to connect the PC and printer. That way, room 3 can access with wifi, and room 2 can physically plug into the Airport Express station. Problem with that is that the Airport Express Card must be professionally installed in my Mac Pro and that $80+ charge on top of the Airport Express and Aiport Card itself, turns this into a $200+ endeavor.
I also have a wireless Linksys router and Linksys WiFi USB receiver. Anybody have any other ideas?
Mac Pro Mac OS X (10.4.9)

Your plan wouldn't work anyway. The Mac Pro can not create a WDS compatible wireless network. Therefore the AirPort Express (AX) can not use WDS to wirelessly join the network. Therefore the AX's Ethernet port will not be activated.
The best solution is to buy an inexpensive wireless router [or the AirPort Extreme base station (AEBS)]. Connect the Mac Pro via Ethernet to the router. Add a wireless adapter to the PC in room 2. Therefore the PCs will connect wirelessly while the Mac Pro connects via Ethernet.

Setting up airport express with airport extreme 802.11n with Airport Utilit

Hi,
I'm having trouble setting up my airport express(AX). Having recently bought the new Airport Extreme (AE) basestation, I can't figger out how to set it up to recognize the AX and allow me to stream airtunes. Previously I had the AX setup fine, but once I installed the AE, it no longer was recognized.
After resetting the AX, the airport Utility recognizes the AE and the AX as basestations, but I don't want to have to switch back and forth from wireless networks everytime I want to listen to music in another room. Airport Admin seemed to have been wiped out when I installed the AE, so any documents I've found on the Apple site refer to AA and not Airport Utility.
HAs anyone set up their AX on the new AE basestation?
thanks!
Rene

I am currently experiencing the same issue, except that I cannot for the life of me get the AX to:
1) Stop flashing yellow - numerous resets -soft to default.
2) The airport utility will not recognize it.
The airport utility sees the AE no problem, I got that up and running after a few restarts and am now able to log on to the network with my laptop.
I am new to Mac's and this is the 1st time I have tried to set up a network with one, I was excited about being able to use the AX to play my iTunes through the stereo in the other room and to hopefully use it to connect my X-Box to the internet. But I am starting to think that this is either above my skills or a fruitless endeavor. Any help would be most appreciated!
Thanks
Fairbanks

Hi! This might be a stupid question, but I just bought an IPod G5 60 GB. When you firstconnect your IPod you have to setup your ID. I'm using my brothers computer, who has an IPod too, so now I'm wondering when I set up my ID with his Itunes does his Ip

Hi!
This might be a stupid question, but I just bought an IPod G5 60 GB. When you firstconnect your IPod you have to setup your ID. I'm using my brothers computer, who has an IPod too, so now I'm wondering when I set up my ID with his Itunes does his Ipod still work with it??? Or would his ITunes just see my IPod? Or does his Ipod ID change to my ID?
Or does it work without any problems, to setup two IDs on the same computer??
Thanks!

Hi!
This might be a stupid question, but I just bought an IPod G5 60 GB. When you firstconnect your IPod you have to setup your ID. I'm using my brothers computer, who has an IPod too, so now I'm wondering when I set up my ID with his Itunes does his Ipod still work with it??? Or would his ITunes just see my IPod? Or does his Ipod ID change to my ID?
Or does it work without any problems, to setup two IDs on the same computer??
Thanks!

We have an older IMac (preIcloud) and just purchased a new Macbook Air. Our Iphones are set-up to synch with the IMAC and my calendars on the IMac & the phone look the same. But when I open ICal on the MacBook Air my calendar is missing items? Help..

We have an older IMac (preIcloud) and just purchased a new Macbook Air. Our Iphones are set-up to synch with the IMAC and my calendars on the IMac & the phone look the same. But when I open ICal on the MacBook Air my calendar is missing items? Help.

Are you wanting to import iCal to the MacBook Air. Since iCloud doesn't work with 10.6 OSX you probably don't have any data in iCloud yet?

How to set up Airport Extreme with Charter ARRIS Modem TM902A for the first time for WIRELESS.

How to set up Airport Extreme with Charter ARRIS Modem TM902A for the first time for WIRELESS.
When Charter Tech goes to your site, have them connect the modem up, but do not connect the modem to your iMAC or MacBook Pro. What you want to do is connect the Airport Extreme to the iMac or MacBook Pro first with the Ethernet Cable. You have to do this to configure via Airport Utility to set up the Base Station Name & Base Station Password.
You will then create/configure a Wireless Network, create your Wireless Password that will be entered on each of your Devices, example, Apple Tv, your iPhone, etc., you want to allow access to your Wireless Network you are creating.
Wireless Security will be -> WPA/WPA2 personal or just WPA2
Enter the Wireless Password you want
Verify the Wireless Password (enter it again)
After it is created you will see it on the Airport Utility window with the name you created for it and to the left, will be a Dot (circle that will be yellow).
Next you then want to unplug the power to the Airport Extreme, and then take the end of the Ethernet cable you unplugged from the iMac or Lap top MacBook Pro and connect it to the back of the Modem.
Next unplug the power cord from the modem and wait about 5 minutes, then plug the power back into the Arris Modem and wait until all lights come back on the modem wait
about 5 minutes, then plug the power cord back to the Airport Extreme and you will see it the light blinking yellow. Wait about 5 to 10 minutes, during this time Restart you IMAC or MacBook Pro, and once it is back up click on the Airport Utility and you should see on the Airport Utility screen.
For INTERNET to the left the light should be green and you should see the Airport Extreme also appear and the light to the left on the screen should also be green. If they are, you then should be able to click on the Wireless Symbol on top of bar of the screen and click to select the Wireless Network Name you created.
If you Do Not See the light (Icon) next to INTERNET turn Green, or if you see the Internet Light Green, but the Light (Icon) next to the Airport Extreme is yellow, unplug the power again to the modem and unplug the power again to the Airport extreme and wait about 15 minutes or up to 30 minutes. Then plug the power cord back to the modem wait till all the lights light up then, plug the power cord back into the Airport Extreme and Restart your iMAC or MacBook Pro.
The Airport Extreme light should change from yellow to green. Open up the Airport Utility to see what the indicators are showing they should both be green. Again select Wireless network you created under the Wireless Icon on the top right of the screen. Open Safari and see if you are able to Route to a web page or the apple site should appear.
WHAT TO DO IF YOUR AIRPORT EXTREME WAS PREVIOUSLY SET UP FOR USE WITH ANOTHER CARRIERS ROUTER OR MODEM.
NOTE: If you already had your Airport Extreme connected for example, I previously had ATT Uverse and the Airport Extreme was connected to the Wireless Router Model 3801HGV, I disabled the Uverse Wireless and used the Airport Extreme for the Wireless signal in bridge mode, as the Airport extreme Signal is much stronger than the Uverse router, and I was able to obtain a Wireless signal with the Airport Extreme way much better with no signal loss which was very very frustrating with the Uverse router.
Anyhow if you had it hooked up like this, now that you will be using it with the Charter ARRIS Modem TM902A, you will need to reset the Airport Extreme to clear out the old data it has in memory, with the previous set up otherwise it will not work. Trust me I spent 6 hours trying to make it work reading all Apple Support Community questions and answers relating to this type issue/problem others have been having trying to get their set up working. I tried all the tips, and I finally decided just to see if by chance I would be able to connect with someone with Charter Tech support who might be familiar with Apple to be able to assist me and by luck I did. He told me why it was not working and was all due the previous configuration with the ATT Uverse router was still in memory with the Airport Extreme. Finally it was 10:30 PM when I decided to call Charter Tech Support and I had been working on this since 3:00 pm pacific. I did not call them earlier as all the post I read said they never received any good help from Charter. After calling them I finished up by 11:00 PM and was able to finally connect Apple Tv, iMac, iPhones and Macbook Pro. We love our Apple Product and Happy all is connected with the new
Internet Provider Charter. I must say the speed is way way much better than it ever was with AT&T Uverse.
THIS IS WHAT YOU WILL NEED TO DO:
First you will need to unplug the Airport Extreme, then by taking the tip of a pen or paper clip end you need to push the reset button on the back of the Airport Extreme and hold it
down and at the same time plug the power cord back into the Airport Extreme count to 5 or 10 then release the reset button. Then once he light in front of the Airport Extreme stops blinking you need to plug the Ethernet cable from the Airport Extreme to your iMAC or Macbook Pro, and restart which ever one you have, then open the Airport Utility once it is back up. If you see airport extreme pop up with the old network name or it shows and yellow triangle click on the Airport Extreme ICON it will not let you configure it but will ask if you want to get rid of it or remove and just do it. Then Again restart your iMAC or MacBook Pro, open up Airport Utility again, and on the top left you should see under “Other Airport Base Stations” the MAC ID for the Airport Extreme.
You will then create/configure a Wireless Network, create your Wireless Password that will be entered on each of your Devices, example, Apple TV, your iPhone, etc., you want to allow access to your Wireless Network you are creating.
Wireless Security will be -> WPA/WPA2 personal or just WPA2
Enter the Wireless Password you want
Verify the Wireless Password (enter it again)
After it is created you will see it on the Airport Utility window with the name you created for it and to the left, will be a Dot (circle that will be yellow).
Next you then want to unplug the power to the Airport Extreme, and then take the end of the Ethernet cable you unplugged from the iMac or Lap top MacBook Pro and connect it to the back of the Modem.
Next unplug the power cord from the modem and wait about 5 minutes, then plug the power back into the Arris Modem and wait until all lights come back on the modem wait
about 5 minutes, then plug the power cord back to the Airport Extreme and you will see it the light blinking yellow. Wait about 5 to 10 minutes, during this time Restart you IMAC or MacBook Pro, and once it is back up click on the Airport Utility and you should see on the Airport Utility screen.
For INTERNET to the left the light should be green and you should see the Airport Extreme also appear and the light to the left on the screen should also be green. If they are, you then should be able to click on the Wireless Symbol on top of bar of the screen and click to select the Wireless Network Name you created.
If you Do Not See the light (Icon) next to INTERNET turn Green, or if you see the Internet Light Green, but the Light (Icon) next to the Airport Extreme is yellow, unplug the power again to the modem and unplug the power again to the Airport extreme and wait about 15 minutes or up to 30 minutes. Then plug the power cord back to the modem wait till all the lights light up then, plug the power cord back into the Airport Extreme and Restart your iMAC or MacBook Pro.
The Airport Extreme light should change from yellow to green. Open up the Airport Utility to see what the indicators are showing they should both be green. Again select Wireless network you created under the Wireless Icon on the top right of the screen. Open Safari and see if you are able to Route to a web page or the apple site should appear.

I just got a Charter Modem. Model TM822. While I was moving, my Airport Extreme was still at my old place.
I have a Linksys WRT320N I used for the initial Charter setup.
I can get my Airport to work here, but the Internet light on the Modem flashes Yellow.
Hasn't caused any issues so far but one thing I did notice.
On the Linksys there were 3 DNS servers listed.
The Airport Extreme only lists 2 and i don't see where I could add another, only change whats already there.
I tried everything above, but light on modem still flashes yellow.
I have the technicians cell phone. Told me "that shouldn't be" and gave the same advice listed above.
I'll break down and call Charter one day, see if it's on their end. NSA tracking may need a reset LMAO.

I have itunes set up to sync with my Ipod Touch and my Ipad. As of today, it keeps looking for an iPhone to sync with and give me an error message. I don't have an iPhone and don't know how to stop it from popping open with this error message.

I have Itunes set up to sync with my Ipod touch and Ipad. As of today, iTunes has started searching to sync with an iPhone, which I don't have and pops open with an error message stating it cannot locate the iPhone to sync. I have looked in devices and only the iPad and iPod Touch are listed. Any ideas on how to stop iTunes from searching for any iPhone it is never going to find? It is annoying to have it popping up all the time with the error message. Thanks in advance for any suggestions.

You should really read the manual.
"How do you restore from backup? "
Restore. When given the choice, choose to use backup.
"And how can I check to see if the pics and videos are on my computer somewhere first??"
They would only be where you put them. What program did you use to import them? Pics/vids taken with ipod are not part of the sync process at all. You should be importing them just as you would with any digital camera.
If you did not import them, then they are not on your computer.

How do I set up a home with 4 Platform components, 3 v. 10 and 1 v. 9.2?

This is probably simple, but I can't find the answer in the various documents. I want to install a home with all the latest Platform components. Since Integration 10 has been delayed, I want to set up a home with Server 10, Workshop 10, Portal 10, and Integration 9.2. How exactly do I do this? After I install the first 3 components, when I try to install Integration 9.2 the installer wants also to install Server 9.2 and Workshop 9.2.
Or is what I'm trying to do even advisable? Does needing Integration mean I have to use Platform 9.2 MP2? How exactly should I set up my home?
Thanks in advance for your help.

I am considering putting three or more OS's on my
computer. Would someone show me how to set up a
master boot record to give me a choice between
Windows XP Professional Edition, Solaris 10 6/06, Red
Hat Linux 7 (Fedora Core 5), and possibly Knoppix
5.0.1, Snappix, and Morphix?Have you seen this article?
http://www.sun.com/bigadmin/features/articles/multiboot_laptop.html
I want the boot record
to be posted in both Windows' BOOT.INI file and in
GRUB.What do you mean by that? You can only have one thing in the MBR, but of course that thing could chain to something else.
Darren

How do i set up a slideshow with pictures from multiple iphoto libraries?

How do i set up a slideshow with pictures from multiple iphoto libraries? One library is in my Macbook Harddrive, the other 2 libraries are in an external harddrive. Thank you!!

You can't, simply. An iPhoto Slideshow can only draw from a single library, so you'll need to get all the images into one.
Alternatives to iPhoto's slideshow include:
iMovie is on every Mac sold.
Others, in order of price:
PhotoToMovie $49.95
PulpMotion $129
FotoMagico $99
Final Cut Pro X $299
It's difficult to compare these apps. They have differences in capability - some are driven off templates. some aren't. Some have a wider variety of transitions. Others will have excellent audio controls. It's worth checking them out to see what meets your needs. However, there is no doubt that Final Cut Pro X is the most capable app of them all. You get what you pay for.

Hi, I have an iTunes account on my laptop set up to work with my old iPod. I now have an iPad and new iPod but set up under a different account- can I put all the songs from my iTunes onto the new devices. Thanks.

Hi, I have an iTunes account on my laptop set up to work with my old iPod. I now have an iPad and new iPod but set up under a different account- can I put all the songs from my iTunes onto the new devices. Thanks.

Yes
Put all the music on one computer, make sure it is authorized for all accounts, sync.

HT204053 If I have set up my Mac with two different users, can I use two different Apple IDs on the same Mac?

If I have set up my Mac with two different users, can I use two different Apple IDs on the same Mac?

Each user account may have its own Apple ID.

Set-up of RE4100W with X3500 gateway

Similar Messages

Maybe you are looking for