Settings for an XP-M 2800 on a KT6 Delta board please.

Can anyone please tell me what FSB settings and core voltage to use on this board as I have just set the FSB to 200 and now I cannot boot. This should be right with PC3200 memory should it not.. Does this chip run at 1.45 volts like the XP2500 mobile. Cheers people.

Do you happen to know what code is on your mobile chip? Putting the code into google will tell you what voltage etc. is needed. There are different varients, so it's best to check that.
I think the mobile CPUs all run at 266mhz FSB though, although many you can overclock to run at what you want, with the unlocked multipliers.
With my XP1800-M I changed the FSB to 333mhz, as it wouldn't run at 400mhz. Just remember to set as half in the BIOS. Remember to set the memory running at the same speed as the CPU.

Similar Messages

BIOS settings for an Athlon XP 2800 processor

Hi Guys (and Gals),
Just got an Athlon XP 2800+ processor upgrade for my MSI KT6 DELTA mobo.
I know that the mobo supports this processor but I am a little confused as to what the settings shopuld be in ther BIOS.
The Athlon XP 2800 has an FSB of 333mhz (I believe) but where do I select this on the BIOS as the CPU FSB clock (in frequency voltage control) only goes up to 280mhz.
Cheers.

"...but where do I select this on the BIOS as the CPU FSB clock (in frequency voltage control) only goes up to 280mhz...."
You should have in mind that the FSB you select is really the half of actual speed, so FSB to be selected -as Wonka advises- is 166 (*2=333) That's why there isn't an option to select 333 in Frequency/Voltage Control>CPU FSB Clock ( it would set the CPU speed to 666 Mhz.)

Error : Pre Settings for IDoc inbound processing are missing error

Hi Experts,
There is a CRM job which executes LSMW and I am facing a strange problem during the IDOC posting the error "Pre Settings for IDoc inbound processing are missing error". Can anyone please tell me how to correct this error?
Thanks in advance.
Madhurima.

I'd start with the following document, with one modification. At step 12 after typing GEARAspiWDM press the Enter/Return key once prior to clicking OK. (Pressing Return adds a carriage return in the field and is important.)
[iTunes for Windows: "Registry settings" warning when opening iTunes|http://support.apple.com/kb/TS3299]

When restoring and updating my iPhone I am getting the following message " iTunes could not update to the carrier settings for your iPhone.an unknown error occurred (1630)

When restoring and updating my iPhone I am getting the following message " iTunes could not update to the carrier settings for your iPhone.an unknown error occurred (1630).can anyone please with a knowledge tell me what I should do please. Thank you

The search bar can be very valuable...........
In using it, I found out other's have had this issue and it likely means you have a 3G iPad? If you do, go into settings and turn off cellular data, then try to update again and you should be OK........

Best settings for highest quality results, Blu-Ray vs DVD

I am shooting AVCHD 1080p 60fps with a JVC GC-PX100, using a Windows 7, i7-2600 3.40Ghz., 8Gb.RAM, 1 TB HDD with PE11 and a Pioneer Blu-Ray writer drive.
I'm looking to find the best settings for replay on a 55" HDTV. I have tested both BD and DVD without seeing very much difference between the two as far as video quality is concerned,
but I want to make sure I'm using the right settings for the best quality on both drives. Can someone please offer a step by step settings procedure for both BD and DVD, also which do you
think is the better route to take between the two?
Also, I have noticed there is a ghosting image after letters/numbers on faster moving content (like railroad cars) on my video even before transferring it, can anyone give some insight to what that might be and if there may be a solution ??
Many thanks for your anticipated help.

Rikko
Thanks for the reply.
Referring back to your post 4.
Additional info: When I published my test video for DVD I chose “Computer” on the Publish+Share drop-down list, then chose MPEG, Presets: HDTV 1080p 29.97 High Quality.
Saved and burned to DVD. I also did the same choosing AVCHD Presets: MP4 – H264 1920x1080p 30. Saved and burned to DVD
Let us clarify. When the end result is "...burned to DVD" in either case, are saying that you take your saved file to DVD-VIDEO on DVD disc or AVCHD on DVD disc, using another Premiere Elements 11 project on Windows 7 64 bit.
My post numbered 1, contained the step by step for taking your 1080p60 Timeline directly to DVD-VIDEO on DVD disc or Blu-ray disc format on Blu-ray disc.
If you are going to introduce intermediates in your workflow (Timeline content saved to file and then burn to disc), then I would offer the following scheme
a. 1080p60 project preset (project 1)
b. 1080p60 Timeline saved to file via
Publish+Share
Computer
AVCHD
with presets = MP4 - H.264 1920 x 1080p30 (and then under the Advanced Button/Video Tab, customize the export settings for 1080p60 instead of 1080p30)
c. Import that back into Premiere Elements 1080p60 project (project 2) and burn to disc DVD-VIDEO on DVD disc, AVCHD on DVD disc, or Blu-ray disc format on Blu-ray disc..
This is another alternative interpretation to your saved and burned to DVD.....in one project, you are doing two different exports...one to a file saved to the hard drive and after than the burn to disc (be it DVD-VIDEO on DVD disc, AVCHD format on DVD disc, or Blu-ray disc format on Blu-ray disc). If this is the case, there is no "intermediate".
There used to be the discussion about HDV to DVD-VIDEO format on DVD disc - whether HDV file should be imported into the project as source or whether the user should downsize the HDV to DV widescreen in the camera before import into a DV Widescreen Premiere Elements project. As we getting into this type of question with your 1080p60 to DV widescreen?
Please review and consider. And, then please let me know if any of the above addresses your considerations.
Thanks.
ATR

Hello All... Back after a brief absence, things look a little bit different. I'm trying to take a 16 minute mini dv video and compress it for use on the web. I'm interested in any suggestions you may have on settings for the video and audio tracks. I'v

Hello All...
Back after a brief absence, things look a little bit different.
I'm trying to take a 16 minute mini dv video and compress it for use on the web. I'm interested in any suggestions you may have on settings for the video and audio tracks. I've tried using Sorenson 3 (15 frames, key frames set to automatic, 320 x 240) for video and IMA 4:1 (mono) for audio. The resulting video looked great but the file size came in at about 255 Mb.
Thanks!
PowerMac G5 1.8 Dual Mac OS X (10.4.3)
Message was edited by: Dan Foley

Thank you for the replies. Everyone was correct about the jack, interface, and phasing problems. I have been unplugging my motu audio interface and then using headphones at work. I have not changed any detailed audio output settings in logic. When I read that the jack might be a problem I tried switching headphones. This actually helped. I am using dre-beats headphones and they seem to be having issues with the mac/jack-(the phasing/panning problems. I can use these headphones with other devices but not the mac. I have to use ipod ear buds and the phasing seems fixed. Hopefully this information is helpful to someone else.
If anyone knows how to correct this issue please let me know its difficult to know what my final mixes are going to sound like and I have had to keep bouncing everything into i-tunes- sync to ipod and then listen in my car radio.

NVidia Settings for Two Different Graphics Cards?

I just built a new system for video editing with Adobe CC 2014 including both the Quadro K4000 AND the GeForce GTX780 DirectCU II OC graphics cards. I was wondering what are the best settings in the NVidia control panel for apps such as Premiere Pro, After Effects, Speedgrade, Encore, etc. I see that there are global settings and app specific settings.
One question I have concerns the CUDA cores. Should I select one graphics card over the other or use the global (all) setting? How does that work? For CUDA, if I select Global, does the system decide automatically which card to use or does it combine the CUDA cores of both cards?? Seems like an important distinction.
Also, I have two monitors: ASUS PA279 (2560x1440) and a JVC PS-420W (1920x1080) How should these be connected to the computer for best performance and picture quality? Should I use DVI or HDMI connections?
And, of course, the Quadro K4200 just appeared on the market, which offers almost double the CUDA cores and 4 GB RAM instead of 3 GB on the K4000. Should I return the K4000 and replace with the K4200? price difference not much.
The rest of my system includes:
Processor - Intel i7-4930k 6-core 3.4 GHz
Motherboard - ASUS P9X79-E WS
RAM - Corsair Dominator 2133 DDR3 64 GB
System drive - Intel SSD 530 Series 240 GB
Storage - WD Black 16TB (4x4TB) RAID 0
UPDATE - I wrote to PNY because it's their Quadro K4000 card, and this was their reply to me:
Hi Alex,
Thank you very much for using our NVIDIA Quadro by PNY professional graphics boards, and for contacting PNY Quadro Support.
Our NVIDIA Quadro K4000 is an excellent choice for supporting Adobe Creative Cloud 2014 for video editing.
Forgive me, but we do not recommend installing Quadro and GeForce graphics boards together in the same configuration. That does not mean that you cannot do it, and honestly, in Windows 7, it may actually be OK to have both cards installed (each with its own driver), but we still do not recommend it, and do not support it.
Furthermore, I support Quadro products only, not GeForce products, so I do not have a lot more to say about the GeForce card, other than to say that GeForce cards are intended for use supporting games and home use, while Quadro graphics boards are intended for use in workstations, supporting professional applications such as Adobe Creative Cloud 2014.
I recommend installing the Quadro K4000 into the primary (top) PCIe x16 slot, and to install the latest ODE graphics driver for it:
http://www.nvidia.com/download/driverResults.aspx/77637/en-us
I recommend using the default settings in NVIDIA control panel. The system will use the card in the primary slot. While Adobe CC applications are multi-GPU aware, and designed to automatically use the second GPU to improve performance, I feel more confident that you will see a benefit by using a second Quadro card in the secondary PCIe slot. I do not know whether Adobe CC will use the GeForce GPU to boost performance, or not (as again, this is not supported or recommended).
For the Asus PA279, I recommend using a DisplayPort (DP) 1.2 cable (or perhaps a dual-link DVI cable) to connect it to the K4000. I recommend using a single-link DVI cable (or perhaps a DisplayPort to HDMI adapter, together with an HDMI cable) to connect the JVC PS-420W to the K4000.
Message was edited by: Alex DeJesus

What a stubborn machine! Whenever I set the CUDA setting to GTX780 and hit 'Apply' it would jump back to the Quadro. Even after changing the Global setting to the GTX780 and back to Premiere it would do that. After a few times, it finally changed to what I wanted. Now Premiere, AE and Speedgrade are set to GTX780 for CUDA. However, there is a graph that shows GPU Utilization and it shows the Quadro still doing the brunt of the work - about 50-60% compared to the GTX at 5-8%. I suppose that's a different setting I need to change?
I had both monitors connected to the Quadro. I just put the 2nd display on the GTX. Does it matter? And does it matter what connector type - HDMI, DVI, etc.?
I set the BIOS to Gen 3 for the slots that the GPUs are in. And enabled 'Above 4G Decoding'. That Quadro is a PCI E 2.0 card. I see a 'little bit' of performance improvement playing back 3 layers of video with effects Magic Bullet Looks and different blending modes. It does not like the Neat Video noise reducer and some of the other effects, though. Still pretty crippled. Maybe a hard drive issue? I've got a 4 x 4 TB RAID 0 WD Black series on the onboard controller. 64 GB RAM is plenty.

Adobe cloud to save automatically actions, stuff and settings for example?

Hi!
I had a hard-disk error and had to reinstall everything and with that I lost my photoshop actions...
Can't adobe cloud save automatically / sync this kind of stuff and personalize settings for example?
Thanks!
Francisco

Hi Francisco, here are the details around sync settings and items that can be synced as of now: Photoshop Help | Sync settings using Adobe Creative Cloud
Thanks,
Atul Saini

HT4864 I am getting a triangle with an exclamation point next to my inbox...it says: There may be a problem with the mail server or network. Verify the settings for account "MobileMe" or try again. The server returned the error: Mail was unable to log in

I can send but cannot recieve email
This is the messege I am gewtting:
There may be a problem with the mail server or network. Verify the settings for account “MobileMe” or try again.
The server returned the error: Mail was unable to log in to the IMAP server “p02-imap.mail.me.com” using “Password” authentication. Verify that your account settings are correct.
The server returned the error: Service temporarily unavailable

Also if I go to system preferences accounts and re-enter the password it fixes the glitch sometimes.

ITunes looses photo sync settings for Apple TV (1st gen.)

Since the update to the new Photo app on my Mac, iTunes forgets the photo sync settings for my Apple TV (1st. generation, 160 GB HDD).
Every time I open the photo section of the Apple TV sync settings, all the options are turned off. Then I mark a couple of albums and sync the Apple TV >> all album appear on the Apple TV.
But after closing and re-opening iTunes in the photo settings everything is unmarked again. So on every following sync the photos on the Apple TV are easily erased :-( Resync them to the Apple TV takes hours (>30'000 photos!).
All the other sync settings in iTunes remain intact.
Environment:
- MacBook Pro Retina 15" with the latest SW (Mac OS, iTunes, Photo App, etc.)
- Apple TV 1st gen 160 GB HDD

Restarting iTunes resolves the issue in the majority of cases, if it doesn't my second guess would be your security software.
What really seems strange here is that there have been no updates since well before Xmas, so after initially setting it up, the first update would have brought you right up to the most recent (and indeed the very last) .
Agh, how silly of me, I see it's iTunes you have updated.
If that's about all you've changed, you might want to try reinstalling iTunes and bonjour.
Message was edited by: Winston Churchill

Different rich text/plain text settings for different accounts?

I use Mail for both my work email (MS Exchange) and my personal email (webmail/IMAP). Many of my coworkers use Outlook's rich text formatting options, so I need to have my work emails go out as rich text. However I'd like to have my personal emails go out as plain text.
I can set Mail to create new messages in plain text, but to reply in the same format of the original message. That takes care of everything EXCEPT when I compose a new message using my work address... in that case it goes out as plain text, and my coworkers complain that they can't use formatting, because their copies of Outlook are in turn configured to reply in the same format as the original message.
So ideally what I'd like is to have two different formatting settings for my two different accounts. Anyone know how this might be done? Any plugins, etc., that might accomplish this?

Since you are running Jaguar, Jaguar and Panther Mail do not support composing in HTML and this includes when forwarding a message received that was composed in HTML.
Since Jaguar and Panther Mail do not support composing or forwarding HTML, you can't embed images or photos in the message body anyway.
RTF with Tiger Mail is really HTML and although Tiger Mail does not include an HTML composer/editor, you can copy/paste HTML format from a web page and forward HTML received.
Images/photos and single page PDF attachments are revealed as inline or viewed in place within the body of the message by default which cannot be turned off. This applies to received and sent messages which is not the same as being embedded. Embedded requires HTML and an embedded attachment is not a true attachment. All Mail.app versions render HTML received but you cannot attach a photo or image as embedded with Jaguar or Panther Mail so it doesn't matter if you use RTF or Plain Text in regards to photo/image or single page PDF attachments which appear as inline or viewed in place within the body of the message by default regardless.
When you use Plain Text for message composition, the receiving mail client renders the text in whatever font the reader chooses.
IMO, everyone should use Plain Text for message composition. Messages would be boring to some but the majority if not all problems experienced with email would be eliminated if HTML was banned from message composition.

TS2446 I just got my iPad, I have an iPod. When I go to put apps on it says my apple I'd Is disabled. I have reset the passwords. Somehow I have two id's? I've gone into settings for apps signed out and back in with the new p.w. I can't think of what e

I just got my iPad, I have an iPod. When I go to put apps on my new ipad it says my apple ID Is disabled. I have reset the passwords. Somehow I have two id's? I've gone into settings for apps signed out and back in with the new p.w. I can't think of what else to do to get the disabled block off. Any ideas?? Thanks

See this Apple document for help...
http://support.apple.com/kb/ts2446

When I try to disable cellular data in the settings for my apps it will toggle fine, but once I exit and go back in to the cellular settings its back on again all by itself.

I have had a problem with my iphone 4s for some time now but I have just been so busy to try and fix it. When I try to disable cellular data in the settings for my apps it will toggle fine, but once I exit and go back in to the cellular settings its back on again all by itself. However, even though it says the data is on, I can’t use the data when I don’t have wifi. I tried restoring my phone a few times and the last time I did that, it wouldn’t turn my service on so I had to talk with a Verizon agent for a long time trying to fix it and finally they simply sent me another phone. I thought hey new phone, this part will be fixed. However, I got my service to work but it’s still the same problem with the cellular data. I have just left it alone and not worried about it, but it’s still not fixed and thought I could ask on here if anyone had any ideas. It has something to do with the apps actually installed on the iphone. Apps like the mail, safari, settings, itunes apps, etc. All my other apps turn on and off just fine. Does anyone have any ideas?

Read the User's Guide... it covers how to backup and sync the device as designed.

How the files are decreasing from RBS storage after some time i delete docs from document library, where shld I check the settings for this?

HI
I created a web application and configured rbs storage ,
I uploaded documents (for ex: 18 number)
after uploaded documents , and observed the RBS storage folder, number of files are increasing (39 number) , its working fine
and also I run the querys to check the rows increasing or not , (when I upload new doc rows are increased its fine also)
select count(*) from alldocs
Select count(*) from AllDocstreams
but when I delete some docs from document library ,
1)the doc itself deleted from document library
2)when I check the rbs storage there is no number of files are decreased(its still 39 files ), its same as before doc deleted from doc library
after some time I found the number of files are decreasing from RBS storage folder in sql server,
here I want to know the how the files are decreasing from RBS storage after some time, where shld I check the settings for this? and how I control on it
here how I know the settings for cleaning up orphan BLBOS how these deleted BLOB
adil

1. WHen you delete the file from Sharepoint, it is still present in Recycle bin. This is a default setting in sharepoint for 30 days. Once files are deleted fro Recycle bin, it can also be delete from RBS
2. There is a RBS cleanup job which deletes files from RBS. for more info check
http://mehuljamod.blogspot.in/2012/09/remote-blob-storage-maintainer-rbs.html

How to change default settings for a video generator?

I'm using a video generator (Lyric Media's Pan Zoom Pro) many times in the same project, and have to change the default settings for each new instance of the generator that I create. I'm wondering if there's any way to change the default settings for a generator (i.e., length of clip, individual slider and checkbox settings in the "controls" tab) so that each new instance automatically has my customized settings when I first open it.
Thanks.

That works for the all the controls/filter settings. The clip length still defaults to 10 seconds, but that's OK, since the main thing I was looking for was to change the clip's internal settings. Thanks for your help

Settings for an XP-M 2800 on a KT6 Delta board please.

Similar Messages

Maybe you are looking for