SF302-08P & MP

What is the difference between SF302-08P and SF302-08MP Switches? Comparison Chart is identical.
Thanks
DJE

Hi Douglas,
MP means "Maximum PoE" meaning that the full PoE specified 15,4 Watts are available simultaniously on all ports.
Best regards,
Zsolt

Similar Messages

Installing SF302-08p with VOIP and Vlans

I am installing this switch to a new departement. The reason of this is to share networks and bring POE over there as we will be istalling VOIP phones next month. We already have a network in place:
-Cisco me 3400 from the ISP
-Cisco ASA 5510 firewall
-Cisco ESW 520 (x3) where access points are connected as well as most part of the network
-Cisco catalyst 3900 (x3) for extra ports
I am actually adding these 2 devices:
-SF302-08P
-WES610N
The SF302-08P will be used for network and VOIP, while the WES610n connects 2 industrial printers to the network.
The network uses VLANS (10 WAN for office, 100 VOIP, 300 WIFI and 309 for management)
Here are my troubles:
The SF302-08P refuse VOIP registration but allows computers
The WES610n connects to access point, allows devices to fetch info from DHCP but blocks every connection except tracert
Any advices or help on this would be greatly appreciated

David
This forum deals primarily with the Cisco Enterprise switches and as such that is the expertise people have here. You have a Small Business switch. No offense intended but you should move this to the Small Business switches forum where you should get the help you need -
https://supportforums.cisco.com/community/netpro/small-business/switches
Jon

SF302-08P small buisiness switch with CNA

I've been using the CNA for our 3560X type switches and really like it.
I saw the lastest version would support the Sx300 switches.
I tried it on some of our SF302-08P switches and it worked great!
But then I tried it on a new one, with newer firmware (1.3.7.18) I got a connection error (said something about not specifying a host name with DNS, but I didn't copy it all down).
Anyone know if that version of firmware has an issue with the latest CNA? (6.1)
I also couldn't update the firmware on the switch to the 1.4.x firmware on the cisco site. Said a mismatch.
Mark

Hi,
Thanks for the response.
the firmware is for the SF302-08P switches.
I use the latest CNA to connect with other 302 switches (older firmware) but not this one with the newer firmware.
That was what I was trying to find out. Is there an issue with the 1.3.7.18 firmware on the 302 switches AND CNA.
Or if possibly I'm doing something else wrong (certainly probable)
thanks
mark

Cisco SF302-08P пропадает с порта trunk native vlan, когда подключаю IP PHONE.

Здравствуйте!
У меня возникла проблема с коммутатором Cisco SF302-08P. В частности проблема заключается в настройке порта для IP phone и ПК.
Как известно это PoE коммутатор.
vlan database
vlan 47,147
exit
voice vlan id 147
voice vlan oui-table add 0001e3 Siemens_AG_phone________
voice vlan oui-table add 00036b Cisco_phone_____________
voice vlan oui-table add 00096e Avaya___________________
voice vlan oui-table add 000fe2 H3C_Aolynk______________
voice vlan oui-table add 0060b9 Philips_and_NEC_AG_phone
voice vlan oui-table add 00d01e Pingtel_phone___________
voice vlan oui-table add 00e075 Polycom/Veritel_phone___
voice vlan oui-table add 00e0bb 3Com_phone______________
hostname DepGrajdIniciativ
ip ssh server
snmp-server server
ip telnet server
interface vlan 47
ip address 172.27.47.253 255.255.255.0
no ip address dhcp
interface fastethernet1
storm-control broadcast enable
storm-control broadcast level 10
storm-control include-multicast
port security max 10
port security mode max-addresses
port security discard trap 60
spanning-tree portfast
switchport trunk allowed vlan add 147
switchport trunk native vlan 47 <-----
macro description ip_phone_desktop
!next command is internal.
macro auto smartport dynamic_type ip_phone_desktop
147 влан для Ip phone. 47 влан для компьютера.
Дело в том, что когда, например, на 1 порт подключаю IP phone (cisco 6921), с порта пропадает настройка "switchport trunk native vlan 47", соотвественно, на компьютере, который подключен к телефону на порт "computer", пропадает связь (теряется vlan 47?). Приходится по новой прописывать, но он сохраняется до следующей перезагрзуки коммутатора или телефона.
P.S. настройки на коммутаторе сохраняем командой "copy run start" или "wr". На телефоне "admin vlan" указан 147.
P.S.S. телефон питается по PoE.
В чем может быть проблема? я работал со многими cisco коммутаторами, но нигде такой картины не видел....

SF302-08P layer 3 mode

Hi,
i'm trying to configure SF302-08P in layer 3 mode.
ports 1 to 8 have ip phones and desktops, port GE1 in connected to a router (not cisco) that links to the internet.
i created vlan 100 and assigned to ports 1 to 8 (untagged)
i created vlan 200 and assigned to port ge1 (untagged)
activated dhcp server , created pool with 192.168.26.0/24 gw 192.168.26.1
                       |router A| (192.168.16.0/24 gw 192.168.16.1)
                           |
                           |
                           | GE1 (192.168.16.14)
                       | SF302-08P |
                                 |
                                 |
SPA504G+DESKTOP |    SPA504G+DESKTOP
        192.168.26.2                      192.168.26.4
         192.168.26.3                      192.168.26.5
the problem that i'm facing is that SPA504G and desktops access the internet with their inter address 192.168.26.0/24 and not 192.168.16.14.
is there a way to achieve what i'm looking ? how does routing work in this case ? shouldn't there be some kind of NAT ?
thank you

Hello Luis,
Is there a particular reason that the switch needs to be in Layer 3 Mode?
I think your scenario would work better if you configure NAT on your router and let the router act as the DHCP server. Then, the switch could be in Layer 2 Mode.
Alex

VLAN setup on SF302-08P switch

I have the following setup using two SF302-08P PoE switches:
1st floor
=========
Switch #1 <-------> private network
<-------> public network
2nd floor
=========
Switch #2 <-------> private network
.... public network (visible but devices can't connect)
I have tried to make the config in switch #2 identical to switch #1, but something is still wrong.
Is this most likely a VLAN setup problem, or what?
Thanks.
Ken Watkins

Tom,
Thanks so much for your help. In my case, the second VLAN is VLAN 50. Here are the pics of what I think you are talking about through the web interface. Do these look like what you are suggesting?
Thanks again.
Ken

Power adaptor of the sf302-08p

Hey,
We are looking for a power adaptor for a cisco switch Sf302-08p. We can't find the adaptor anymore and we have to orde a new one, but we can't figure out the order number of the adaptor. The voltages is 48vdc and has an 4 pin connector . Do someone know the type or ordernumber of this adaptor?
Thanks a lot.
Stefan

Hi Stefan, the power adapter does not have a separate part number. What you can do is call the SBSC, a lot of times they will RMA a whole unit to you then you may remove the power adapter and ship back the unit that was sent. The SX300 RMA process is always advance replacement since it is the defined service level for the warranty.
-Tom
Please mark answered for helpful posts

19" Rackmount-kit included with 8-port switch SF302-08P?

Hi, distribution can´t tell me if rackmount kit 19" is included in 8-port models... can anybody tell me? Thanks a lot!

Yes, it is. From techdata.com:
WHAT'S IN THE BOX
Cisco Small Business SF302-08P
Serial cable
Rack mounting kit

Cisco SF302-08P (SRW208P-K9-NA) Support for Cisco IP 7942 Phones

Hi All,
I am looking at quoting the SF302-08P for a client which will have three small offices interconnected via single mode fiber. I am planning on connecting them to a 3560 switch. Each office will have no more than 3 - 7942 phones. I reviewed the notes on this switch and it seems it should support this phone type without any issues. Could you advise if you have run into any support/reliability issues with this switch and the 7942s?
Thank You,

Hi RevereORL,
My concern is there are;
slight nuances or differences between the CLI configuration on the SG300 compared to the Catalyst range.
I am also very very slightly concerned about post sales support interaction between TAC and SBSC, but these days there is much more cross talking between these two support groups.
Different SFP SKU's for fiber connectivity GLC- series for catalyst and MGB series on 300, even though I have no issue with plugging the GLC SKU's into my 300 series product.
The SF302-8P has a POE budget defined as 62W across all 8 ports or 62watts / 8 ports= 7.75 approx watts that can be drawn from each port.
With the software upgrade to 1.1.1.8 the 300 series now also supports pre-standard POE as well as the 802.3af, power should not be a issue..
I guess the beauty of buying from a distributor, and keeping the packaging, is that your can validate your application.
Give it a try,.
regards Dave

SF302-08P Switch VLAN Problem

Hello
I have a problem configuring a SF 302-08P switch for VLAN. Here is my setup. I have two switches that are configured almost the same. The first switch is a SF200-24P with 12 ports on VLAN1 and twelve ports on VLAN2. The G1 port is the incoming trunk with 1UP, 2T and the G2 port set to 1UP, 2T connecting to the G1 port on the SF302-8 switch. Both Vlans work OK on the SF200-24 switch. The port on the SF200-24 is set to trunk 1UP,2T and the G1 port on the SF302-8 is set to trunk 1UP,2T. The VLAN port membership on the SF302-8 is set to VLAN 1 port 1-4 is 1UP and VLAN 2 port 5-8 is set to 2UP. Ports 1-4 work OK but the 5-8 will not connect to vlan 2. I have downloaded the latest firmware for the SF302 but it did not make any difference. Any suggestions on what I am missing?

Tom
Ok maybe I can explain this a little different. I inherited this project that two parts were built prior to me. The router is a Sonicwall that has too LAN connections with 192.168.1.x on one LAN and 192.168.2.x on the second LAN. That router is connected to a Cisco SF20024P switch on the first floor of a building. The first floor is connected to a second floor switch which is a SF20024P with the same configuration. Both first floor and second floor works great. There is a third floor which is a much small area that only needed an eight port switch. This is where I came in and installed the third switch which is the SF302-8P. The first floor switch passes traffic up to the second floor switch using a trunk with vlan 1 untagged and vlan 2 tagged. The second floor switch takes in traffic fine and works great. Why should the second switch not pass the vlan 2 traffic to the third switch? It should pass it up to the third switch using the same tagging method. As I said the traffic on vlan 1 works on the third switch, just vlan 2 will not.
Thanks

How do I access the web utility with model cisco sf302-08p ?

Hi,i have a problem with the model Cisco SB SF302-08PP Switch , i connect a cable rj45 to my pc and configure the adapter local area connection (ip address:192.168.1.252), the LEDs blink green, and go to the address bar and get the IP by default, which according to the manual is 192.168.1.254 and the result is: page not found. Is there any way to change the web utility? How do I access the web utility?

restore the switch by holding more than 30 seconds and try accessing with ip 192.168.1.254. username and password is "cisco". before change your base ip to 192.168.1.2-253.try to ping and check the connectivity

IPv6 address autoconfiguration vs static on SF302-08P

I've just installed a 302-08P in my office so that we can get our VoIP trunks into our office, so my officemate and I can actually test
the phones before we hand them out. (Can't do that easily with the 1 RJ-45 facilities gave us...)
I noticed that I can not enable IPv6 address autoconfiguration for the management interface, as well as set a static IPv6 address.
This seems wrong: I want the device to always AC an address: it makes bonjour and renumbering much easier. But,
I want to give the device a static IP for purposes like management, DNS, etc. If this unit failed, I'd replace it but it's address would not change.
IPv6 hosts (which the management interface is) should be completely happy with having multiple addresses on an interface, not just
having addresses from multiple prefixes. What gives?

houmles wrote:I found that I can't have two gateways on one interface, but until now there's no problem.
I suspect it's a problem with that; I've noticed this problem as well.
When trying to add multiple default gateways with iproute2 (ie, `ip r a default via xxx:xxx:xxx::xxxx`) it errors with the error you've mentioned. I'm not sure if this is a kernel bug, iproute2 bug, or not a bug at all.
Having multiple default IPv4 gateways works fine.
I believe netcfg doesn't check for an existing gateway and delete it first (or use `ip r r` instead or `ip r a`) before adding the one; but I haven't checked the code so I could be wrong.
EDIT:
OK, I couldn't resist looking at the code, and it indeed does a 'dumb' addition of the gateway:
112 if [[ -n "$GATEWAY" ]]; then
113 report_debug ethernet_iproute_up ip route add default via "$GATEWAY" dev "$INTERFACE"
114 if ! ip route add default via "$GATEWAY" dev "$INTERFACE"; then
115 report_iproute "Adding gateway $GATEWAY failed"
116 fi
117 fi
I'm looking at making a patch now. Patch and bug report: https://bugs.archlinux.org/task/29480
Last edited by fukawi2 (2012-04-16 01:00:09)

Rackmountkit for Cisco SF302-08P included?

Hi, distribution can´t tell me if 19" rackmount kit is included for 8-port models in "mounting-kit". Does anybody know if it comes with kind of "ears" for the switch? Would like to know because client is asking for 400 pcs...

Hi,
19" rack-mount kit with 1U Rack space will be provided with device box.
Package Contents
●  Cisco 300-series Ethernet Switch
●  Power Cord (Power Adapter for Desktop SKUs)
●  Mounting Kit included in all SKUs, including Desktop models
●  Serial Cable
●  CD-ROM with user documentation (PDF) included
●  Quick Start Guide
Refer the below link:
http://www.cisco.com/c/en/us/products/collateral/switches/small-business-smart-switches/data_sheet_c78-610061.html
regards
Moorthy

SF302-08P qos police to zero

Is it possible to police traffic to 0bit/s?
Is it possible to attach a service policy to a vlan interface?

Hi Ed,
This is not typical of the switch. First, please ensure the switch is on at least the 1.1.2.0 firmware, this is the most stable release. There is a new release as of this week 1.2.7.76 if you'd like to give this a go as well. After the firmware flash/upgrade, factory reset the unit.
I would recommend to start with layer 1 and layer 1 related settings. Such as port negotiation. If you check the port management, are you negotiation 10, 100, 100, full or half duplex? Do you see any kind of port flapping on the log? (link up, link down for any of the ports).Can you try to disable the EEE (energy efficient ethernet) globally and on the interface settings? If you go to the smart port section and go to interface setting, does it appear the smart port negotiated anything with the modem?
-Tom

No menu available since upgrading to firmware 1.3.7.18 on SF302-08P

Upgraded to latest firmware and am trying to access the cli menu but the menu command is no longer available
Due to a config issue I am probably going to have to factory reset and the only way I could get a default gateway assigned to the switch was via menu. There seems to be no such option via CLI
Pls advise

Login to CLI:
switch(config)# ip default-gateway 192.168.XX.XX

SF302-08P & MP

Similar Messages

Maybe you are looking for