Cisco SF302-08P (SRW208P-K9-NA) Support for Cisco IP 7942 Phones

Hi All,
I am looking at quoting the SF302-08P for a client which will have three small offices interconnected via single mode fiber. I am planning on connecting them to a 3560 switch. Each office will have no more than 3 - 7942 phones. I reviewed the notes on this switch and it seems it should support this phone type without any issues. Could you advise if you have run into any support/reliability issues with this switch and the 7942s?
Thank You,

Hi RevereORL,
My concern is there are;
slight nuances or differences between the CLI configuration on the SG300 compared to the Catalyst range.
I am also very very slightly concerned about post sales support interaction between TAC and SBSC, but these days there is much more cross talking between these two support groups.
Different SFP SKU's for fiber connectivity GLC- series for catalyst and MGB series on 300, even though I have no issue with plugging the GLC SKU's into my 300 series product.
The SF302-8P has a POE budget defined as 62W across all 8 ports or 62watts / 8 ports= 7.75 approx watts that can be drawn from each port.
With the software upgrade to 1.1.1.8 the 300 series now also supports pre-standard POE as well as the 802.3af, power should not be a issue..
I guess the beauty of buying from a distributor, and keeping the packaging, is that your can validate your application.
Give it a try,.
regards Dave

Similar Messages

  • Cisco prime 2.1 / 2.2 support for Cisco ise 1.3 ?

    Hi, I just tried to connect cisco PI 2.1 to cisco ISE 1.3, but fails.
    I read the release Notes, only ISE 1.2 ist supported.
    But I was wondering that the ssl handshake fails (I have done a packet capture). 
    So PI 2.1 has not tried to connect to ise 1.3 via api, because of the connection fails at the ssl handshake stage.
    Anyway, does anybody know if ISE 1.3 will be supported with PI 2.2 or a version of PI 2.1.x ?

    Why doesn't the REST API communication in Prime 2.1 (2.1.0.0.87) support TLS? The platform itself seem to be able to handle TLS-DHE-RSA with AES-128-CBC-SHA. Why is it trying to use SSLv2 ?
    These protocol is incompatible and very much outdated: http://en.wikipedia.org/wiki/Transport_Layer_Security#SSL_1.0.2C_2.0_and_3.0
    Can this behavour be reconfigured in CLI or at least be allowed in ISE 1.3 to make a workaround until a working patch or upgrade is done? Could or should adding the Cisco Prime server as managed node in ISE circumvent the incompability?

  • Cisco SF302-08P пропадает с порта trunk native vlan, когда подключаю IP PHONE.

    Здравствуйте!
    У меня возникла проблема с коммутатором Cisco SF302-08P. В частности проблема заключается в настройке порта для IP phone и ПК.
    Как известно это PoE коммутатор.
    vlan database
    vlan 47,147
    exit
    voice vlan id 147
    voice vlan oui-table add 0001e3 Siemens_AG_phone________
    voice vlan oui-table add 00036b Cisco_phone_____________
    voice vlan oui-table add 00096e Avaya___________________
    voice vlan oui-table add 000fe2 H3C_Aolynk______________
    voice vlan oui-table add 0060b9 Philips_and_NEC_AG_phone
    voice vlan oui-table add 00d01e Pingtel_phone___________
    voice vlan oui-table add 00e075 Polycom/Veritel_phone___
    voice vlan oui-table add 00e0bb 3Com_phone______________
    hostname DepGrajdIniciativ
    ip ssh server
    snmp-server server
    ip telnet server
    interface vlan 47
     ip address 172.27.47.253 255.255.255.0
     no ip address dhcp
    interface fastethernet1
     storm-control broadcast enable
     storm-control broadcast level 10
     storm-control include-multicast
     port security max 10
     port security mode max-addresses
     port security discard trap 60
     spanning-tree portfast
     switchport trunk allowed vlan add 147
     switchport trunk native vlan 47                 <-----               
     macro description ip_phone_desktop
     !next command is internal.
     macro auto smartport dynamic_type ip_phone_desktop
    147 влан для Ip phone. 47 влан для компьютера.
    Дело в том, что когда, например, на 1 порт подключаю IP phone (cisco 6921), с порта пропадает настройка  "switchport trunk native vlan 47", соотвественно, на компьютере, который подключен к телефону на порт "computer", пропадает связь (теряется vlan 47?).  Приходится по новой прописывать, но он сохраняется до следующей перезагрзуки коммутатора или телефона.
    P.S. настройки на коммутаторе сохраняем командой "copy run start" или "wr". На телефоне "admin vlan" указан 147. 
    P.S.S. телефон питается по PoE.
    В чем может быть проблема? я работал со многими cisco коммутаторами, но нигде такой картины не видел....

  • Android tablets supported for Cisco Jabber for Android 10.5 ?

    Exist a list with tablets support for this realease ?
    In release notes only include smartphones.
    Anoher question, is about version android client, in google play exits a old version, but not 10.5, any reason for this ?
    Thanks in advance.

    The tab listed for support is " Google Nexus 10 (Android OS 4.4.x) ". Please refer to the following link for more information;
    http://www.cisco.com/c/en/us/td/docs/voice_ip_comm/jabber/10_5/CJAB_BK_D6497E98_00_deployment-installation-guide-ciscojabber/CJAB_BK_D6497E98_00_deployment-installation-guide-ciscojabber_chapter_011.html#CJAB_RF_D3CF90B1_00
    Quoting the following link; https://play.google.com/store/apps/details?id=com.cisco.im&hl=en ;we have got the J4A 10.5 listed on the playstore.
    - please rate if this helps.

  • What to support for Cisco IP Phone 7912?

    dear all.  please help me!!!
    I have a 7912 ip phone, and using Cisco CME in 1760, but I do not see this type 7912 ip phone telephony service there. whether it was true ip 7912 phone is not support for the Cisco 1760 CME. and whether support for the cisco 7912 ip phone?  whether the telephony-service configuration is equal to the telephony-service configuration for the ip phone 7940?
    please help me  !!!

    Hi to all
    Please I ned some advice , I was try to reset to factory defaults a Cisco IP Phone 7912 and I was failed .
    Please can you help me ?
    Thanks a lot !
    Hugo Baez

  • Cisco Prime LMS 4.1 - Support for Cisco Catalyst 3560-C Series Switches

    Hello together
    I have a customer which uses the following switch. Last year I have installed LMS 4.1 for him to manage the switches. Unfortunatly the switch model is not supported. According to the information found on the following site the switch is supported for most of the modules in LMS:
    http://www.cisco.com/en/US/docs/net_mgmt/ciscoworks_lan_management_solution/4.1/device_support/table/lms41sdt.html
    The oid object of the device is the following: 1.3.6.1.4.1.9.1.1465
    Supported Software: 12.2(55)EX (Customer has 12.2(55)EX3
    Version Support Type: Device Update
    So I updated all device updates I was able to find.
    Step 1: For that I went to Admin > System > Software Center > Schedule Device Downloads and created a job where I have downloaded the latest versions of all packages.
    Step 2: Installed the downloaded packages Admin > System > Software Center > Device Update and installed all the packages.
    Unfortunatly I don't see the same result like described in the Supported Device Table for LMS 4.1.
    - Cisco View -> works
    - Inventory and Config Collection -> works
    - Fault Monitor not working -> Error Code Unsupported
    - Network Topology Layer 2 Services -> Device Type ciscoProducts.1465, Symbol Question Mark
    - VLAN Management -> Doesn't work
    - User Tracking > seems also not to work
    When I open the report for supported devcies (Reports > System > Device Support) and search for C3560C... I find the following devices, but not mine which i need:
    C3560C-8PC-S     .1.3.6.1.4.1.9.1.1466
    C3560CG8PC         .1.3.6.1.4.1.9.1.1317
    C3560CCG8TC     .1.3.6.1.4.1.9.1.1318
    wsC3560CPD8ptS     .1.3.6.1.4.1.9.1.1368
    Does anybody have experience with the same switch type / model? Am I doing something wrong or is this type of switch not implemented correctly till now? Further the docuemntation supported devices would be wrong.
    Thanks for any feedback Erich

    Thanks but I just heard back from my Cisco SE and he assures me that an AP will NOT use up a license.
    I've asked him to verify his answer for me.
    Is your answer based on real world expereince (the best there is)?  That is, are you running Prime LMS 4.1 and does it indeed use up a license for each light-weight AP it discovers & manages?
    Thanks for mentioning options 1-3 but I do not wish to employ any of them.  I don't mind buying the additional licenses for APs ... I just need to know if I have to or not.
    Ian.

  • Support for Cisco VPN "mutual group authentication"

    Hi,
    Does anyone know of support plans for Cisco VPN mutual group authentication in the built-in VPN client on MacOSX?
    Thanks,
    John

    I would like to know the answer to this as well.
    Thanks,
    Josh

  • Rackmountkit for Cisco SF302-08P included?

    Hi, distribution can´t tell me if 19" rackmount kit is included for 8-port models in "mounting-kit". Does anybody know if it comes with kind of "ears" for the switch? Would like to know because client is asking for 400 pcs...

    Hi,
    19" rack-mount kit with 1U Rack space will be provided with device box.
    Package Contents
    ●  Cisco 300-series Ethernet Switch
    ●  Power Cord (Power Adapter for Desktop SKUs)
    ●  Mounting Kit included in all SKUs, including Desktop models
    ●  Serial Cable
    ●  CD-ROM with user documentation (PDF) included
    ●  Quick Start Guide
    Refer the below link:
    http://www.cisco.com/c/en/us/products/collateral/switches/small-business-smart-switches/data_sheet_c78-610061.html
    regards
    Moorthy

  • Are the SG500P SMB switchs supported for Cisco Network Assistant?

    Hi, we need to enroll some SG500-28P switches to a CNA? Is this possible? I suppose that CDP feature allow this. Actually, i have installed CNA Ver. 6.0. Thanks in advance.

    Hello Fernando,
    Thank you for visiting the Cisco Support Community! 
    Here is a list of all the devices supported by the Cisco Network Assistant for the 6.0 version and later. Many of the 500 series switches, including the SG500-28P Managed Switch, are supported by the CNA. This page will also give you any additional information you may need such as the features of the CNA 6.0 version, any system requirements, and more. 
    If this post was helpful, please remember to mark this question as resolved to help others in the community! If you have any further questions, please do not hesitate to ask!
    Best,
    LP

  • CLI support for Cisco SG100D-05 5-Port Gigabit Desktop Switch

    I would like to know if the SG100D series of switches support the CLI? If not what are the series of switches supported by the CLI.
    I am looking for an application where I need to tell which device is connected to which port on a switch. Hence I am looking at this option where I can run a script and use CLI to output the MAC id of devices connected on each port.
    Thanks!

    Hi Yiu Kay Lee,
    Thank you for sending me this document. It was very helpful. But I cannot understand one thing about it. Is it possible to extract the results from the CLI by passing a command via a script e.g. Python and get the results of it into Python?
    For e.g.
    ************Python script ******************
    >>print("send command to 200 series Cisco switch")
    >> results = show mac-addr-table
    >> print results
    Please let me know if such interfacing with the CLI is possible or not?
    Thanks

  • How do I access the web utility with model cisco sf302-08p ?

    Hi,i have a problem with the model Cisco SB SF302-08PP Switch , i connect a cable rj45 to my pc and configure the adapter local area connection (ip address:192.168.1.252), the LEDs blink green, and go to the address bar and get the IP by default, which according to the manual is 192.168.1.254 and the result is: page not found. Is there any way to change the web utility? How do I access the web utility?

    restore  the switch by holding more than 30 seconds and try accessing with ip 192.168.1.254. username and password is "cisco". before change your base ip to 192.168.1.2-253.try to ping and check the connectivity

  • Error Compilation MIBs Supported for Cisco UCS C-series software release 1.4(3) and later releases on IBM Director 6.3.2

    Hi,
    I have an IBM director 6.3.2 on a Windows Server 2008R2
    I try to install the MIB for manage Cisco UCS C-460 server.
    I downloaded the mib on the cisco ftp.
    the files extension was my. I cahgne it to .mib. For the moment I success to import some ones.
    But when I try to install Cisco-Unified-Computing-TC-MIB, I have got the error in the join file.
    Ho can I fix this issue...

    Hi,
    I have an IBM director 6.3.2 on a Windows Server 2008R2
    I try to install the MIB for manage Cisco UCS C-460 server.
    I downloaded the mib on the cisco ftp.
    the files extension was my. I cahgne it to .mib. For the moment I success to import some ones.
    But when I try to install Cisco-Unified-Computing-TC-MIB, I have got the error in the join file.
    Ho can I fix this issue...

  • Nokia Lumia support for Cisco WLC

    Dear All,
    I am using Cisco Wireless LAN Controller 4404 in my network, All devices (Laptops, samsung mobile phones, Iphone, HTC, etc) are connecting and working perfectly but NOKIA Lumia mobile phone is unable to connect.
    Is there any hotfix for WLC available? please advise
    Regards,
    Junaid

    Please find below debug details, I started debugging the device by command debug client (client mac) and then tried to connect the device.
    *dot1xMsgTask: Sep 25 12:14:03.096: ec:f3:5b:d3:99:20 dot1x - moving mobile ec:f3:5b:d3:99:20 into Connecting state
    *dot1xMsgTask: Sep 25 12:14:03.097: ec:f3:5b:d3:99:20 Sending EAP-Request/Identity to mobile ec:f3:5b:d3:99:20 (EAP Id 1)
    *Dot1x_NW_MsgTask_0: Sep 25 12:14:03.148: ec:f3:5b:d3:99:20 Received EAPOL START from mobile ec:f3:5b:d3:99:20
    *Dot1x_NW_MsgTask_0: Sep 25 12:14:03.148: ec:f3:5b:d3:99:20 dot1x - moving mobile ec:f3:5b:d3:99:20 into Connecting state
    *Dot1x_NW_MsgTask_0: Sep 25 12:16:05.035: apfGetRsnIE: Processing WPA/RSN IE type 48, length 56 processed only 38 bytes
    *Dot1x_NW_MsgTask_0: Sep 25 12:16:05.076: apfGetRsnIE: Processing WPA/RSN IE type 48, length 56 processed only 38 bytes
    *Dot1x_NW_MsgTask_0: Sep 25 12:16:05.076: apfGetRsnIE: Processing WPA/RSN IE type 48, length 56 processed only 38 bytes
    *Dot1x_NW_MsgTask_0: Sep 25 12:16:05.076: apfGetRsnIE: Processing WPA/RSN IE type 48, length 56 processed only 38 bytes
    *Dot1x_NW_MsgTask_0: Sep 25 12:16:05.112: apfGetRsnIE: Processing WPA/RSN IE type 48, length 56 processed only 38 bytes
    And on cell phone it shows the following message:
    connection unsuccessful,
    the credentials provided by the server couldn't be validated,
    I tried to connect it without any encryption and it got connected successfully, issue only on wpa2-Enterprise.
    Please advise,,,
    Regards,
    Junaid

  • Support for SPA932 with SPA525G phone on the UC520

    Will the SPA932 be supported with the SPA525G phone on the UC520 in SCCP mode?
    The command for configuring the SPA525G with a SPA932 would be similar to the following when such feature is supported:
    ephone 1
    device-security-mode none
    video
    mac-address 0021.A000.D001
    username jdoe password "jdoe"
    type 525G addon 1 932
    keep-conference
    button 1:1
    I do know that the following addon module combinations are supported on the UC520:
    796x / 7914
    797x / 7914
    7962 / 7915
    7965 / 7915
    7975 / 7915
    7962 / 7916
    7965 / 7916
    7975 / 7916

    There are no plans to support the SPA932 in SCCP mode. A new sidecar will be offered for the CP-500 series and the SPA525G in SCCP mode.
    Thanks,
    Marcos Hernandez
    Technical Marketing Engineer
    Cisco Systems, Inc.

  • Cisco Aironet Conversion Tool Version 2.1 for Cisco IOS Software

    I am trying to convert a LWAP to Cisco IOS and the tool wants to know the Admin Name*? This is a factory radio sent to me as LWAP. I cannot seem to find out what the Admin Name is, I have tried Admin and Cisco not sure what else to try.

    Hi Brian,
    That tool is used for the IOS to LWAPP upgrade only. The AP can be converted back to Autonomous (IOS) using the following method;
    Reverting the Access Point Back to Autonomous Mode
    http://www.cisco.com/en/US/products/hw/wireless/ps430/prod_technical_reference09186a00804fc3dc.html#wp161272
    You can convert an access point from lightweight mode back to autonomous mode by loading a Cisco IOS Release that supports autonomous mode (Cisco IOS release 12.3(7)JA or earlier). If the access point is associated to a controller, you can use the controller to load the Cisco IOS release. If the access point is not associated to a controller, you can load the Cisco IOS release using TFTP.
    Using a TFTP Server to Return to a Previous Release
    Follow these steps to revert from LWAPP mode to autonomous mode by loading a Cisco IOS release using a TFTP server:
    Step 1 The static IP address of the PC on which your TFTP server software runs should be between 10.0.0.2 and 10.0.0.30.
    Step 2 Make sure that the PC contains the access point image file (such as c1200-k9w7-tar.122-15.JA.tar for a 1200 series access point) in the TFTP server folder and that the TFTP server is activated.
    Step 3 Rename the access point image file in the TFTP server folder to c1200-k9w7-tar.default for a 1200 series access point, c1130-k9w7-tar.default for an 1130 series access point, and c1240-k9w7-tar.default for a 1240 series access point.
    Step 4 Connect the PC to the access point using a Category 5 (CAT5) Ethernet cable.
    Step 5 Disconnect power from the access point.
    Step 6 Press and hold MODE while you reconnect power to the access point.
    Step 7 Hold the MODE button until the status LED turns red (approximately 20 to 30 seconds) and then release.
    Step 8 Wait until the access point reboots, as indicated by all LEDs turning green followed by the Status LED blinking green.
    Step 9 After the access point reboots, reconfigure it using the GUI or the CLI.
    From this doc;
    http://www.cisco.com/en/US/products/hw/wireless/ps430/prod_technical_reference09186a00804fc3dc.html#wp161272
    Hope this helps!
    Rob

Maybe you are looking for

  • Is there any way to repeat the last action on a new selection?

    I'm playing with Pages to see if I can use it instead of Word. I'm very expert with Word, just starting with Pages. Like some things, don't like some, but I think it's worth continuing to play with it to see if it will work for me. One problem I've b

  • Hp LaserJet 1536dnf MFP will not copy via auto feeder

    The printer will print and scan, and copy from the glass just fine too. The problem is when you want to copy from the auto feeder. You put the paper in and press copy. It feeds it through but nothing prints out.

  • How to create a link to download a .psd or .eps file

    I'm attempting to create a link to a .psd file for a user to download. Whenever I link to the .psd file, Dreamweaver wants to convert it to a JPEG. Is there a way to link to a .psd file to have the user download that file? I'm trying to have files th

  • Command Line Scripts in File Adapter

    Hi, In the file adapter, does the command line script support "PERL" Scripts. thanks. Krishnan

  • How do I find BOTH the raw and the cameras jpeg files?

    I've got Aperture 3 importing raw plus jpegs from my Nikon D600 camera. The D600 produces amazing jpegs! Aperture is set to use the raw file as the master. I'd hoped that I'd have access to both the raw AND the camera jpeg but I only see the raw file