Shipping the G4 and monitor

I am curious to know if any one else shipped their G4 and monitor recently and whether they did it by Fed Ex air or ground and how much it cost, even approximately.

As one who buys G4s (to refurbish and resell) shipped from all over the country, I can volunteer a few thoughts.
Fed Ex trucks are smaller than UPS, but they seem to do the job.
The cost I wind up paying for seems to be about $25-30 if the customer does the packing. If you pay to have it done, add $50. If you no longer have the original box, get a large, stout box and use lots of bubble wrap and/or plastic peanuts. Macs travel pretty well.
A CRT monitor is a different story; they DON'T travel well. Back when I bought several and had them shipped, the toll was $50-100 and I tended to lose about half. They are heavy, but mostly, they are unbalanced (front-end heavy), and that means they get dropped, or roll off the top of a six-high stack. They need to be packed sitting on their base, and off-centre in their box, so that their weight is centred within the box. If you have the original box, you might try, but unless you're an expert, give yours away at your end and buy another at the destination.
My limited experience experience with flat screen displays suggest they travel pretty well.
HTH .... Jon

Similar Messages

  • I upgraded both of my phones to an LG3 on 12/21. I was told they would ship on the 23rd. Then I received a notice that they would ship the 26th, and my ordered date was changed from 21st to the 24th. My aunt, who ordered her phone on the 23rd already got

    Please advise, thank you,

    oops....sorry about the long header. 
    My aunt, who ordered her LG3, 2 days after me, got hers today. You are already billing me for the upgrades and I would love some solid information about what is going on. I would not have bought these phones at this time if I knew I was getting this run around. Thank you.

  • Will mac pro and monitors ordered together ship at the same time?

    Will Mac Pro and Thunderbolt monitors, if ordered together, ship at the same time? Or will they ship the in-stock monitors now initiating the Applecare start date for the whole order even though the Mac Pro is not expected to ship until sometime in March?

    I ordered the new Mac Pro (model 6.1) on December 18, 2013 along with a 27 in. Apple thunderbolt display.  The fully maxxed out new Mac pro shipped on January 8, 2014 and arrived January 13, 2014.  My Thunderbolt display shipped within 1-2 days of placing the order, i.e. the week of December 18th and arrived before Christmas.  A few days after receivng my new Mac Pro, I received the Apple Care paperwork and both the new Mac Pro and the Apple Thunderbolt display were listed with a start date of January 7, 2014, i.e. the day that my new Mac {ro was prepared for shipment -- not the day my thunderbolt display was shipped.
    Tom

  • MBPro and monitor not staying asleep; new problem

    Suddenly my new MBPro and its 24" monitor won't stay asleep!.
    I ordinarily use the 24" monitor, leaving lid on my MBPro shut.
    At night, I choose 'sleep" from the Apple menu and the mac and monitor sleep.
    Suddenly, past couple of days, when I do this,
    -monitor sleeps and then within seconds it pops awake
    -If I raise the lid of my MBPro, the monitor of the laptop is black, does not come up until I use Software preferences to "detect display"
    -only way I can keep both monitor and mac asleep is if I leave the lid of my MBPro up, then choose sleep, then the mac and monitor rest.
    I suspect one of the recent sofware updates may be doing this.
    Anyone else experiencing this?
    Should I reset the PMU on the monitor?
    (Does anyone know the precise steps todo this; I know about removing the battery and holding power key for 5 seconds but have been given different advice on removing power cord or not)

    I've got a very the similar problem. Brand new iMac 24" that shipped with Leopard -- my first Mac after jumping ship fom the Windoze side.
    I had iTunes updating it's album artwork and since it was taking a while, I went to bed. When I turned out my light, I realized the screen had not yet gone to sleep (a good 15 minutes after it should have). So I set up a Hot Corner to put the display to sleep. When I put the mouse there, the monitor would go to sleep, but wake up within 10 seconds. At first I thought it was just the mouse moving as I walked away, but it wasn't.
    I ended up turning the computer off because the big beautiful screen was throwing too much light. Since, I rarely turn my computers off and they're usually doing SOMETHING, this is really annoying.
    Admittedly, I haven't tried some othe the potential solutions above, but this has to be the same bug. Screen saver stays on, monitor comes out of sleep.
    Any help would be.....well.....helpful.
    Ian

  • Poor video playback in Encore 2.0 preview and monitor window . . .

    I'm having a strange issue with my video playback in the preview and monitor windows. At some points it displays as blocks (like digital noise). I unchecked the "Automatic" option in the A/V Output dialog as described in the manual. Still, nothing changed.
    To make sure it was Encore that had the problem, and not the file, I played my MPG2 files through PowerDVD, and nothing wrong with the playback in there. What is Encore 2.0 doing? How can I fix this problem???
    Any help would be appreciated!
    Thanks!
    Laz

    What Mouse drivers are you using please?
    This might sound silly, but under 1.5 (Different preview engine, true, so this may be completely wrong) I found that with a later revision of the MS Intellipoint drivers, I had exactly the same issue.
    We worked this out by realizing the green blocks appeared as soon as the mouse was moved. As with your cases, the discs still burned true proving it is a preview related issue.
    Uninstalling & reverting back to version 4.1 made it all go away.
    But since the preview engine is now the PPro one, this might not work any more.

  • BitLocker Administration and Monitoring Reports Error

    When attempting to run Reports through the Administration and Monitoring console I receive the following error...
    "The report server cannot open a connection to the report server database. A connection to the database is required for all requests and processing. (rsReportServerDatabaseUnavailable)"...
    What or how can I verify the connection between the report server and report server database (SQL Database Server) is occurring. Also, which logs can I review to determine what's causing this error...

    Hi,
    go to your Report Server and check if there is an MBAM Folder. Within that Folder you can check the DataSource and verify the target db and Connection Details.
    /Oliver 

  • WVC54GCA - recording and monitoring utility

    I have a couple of WVC54GCA cameras, but don't find the install CDs anymore.
    Now, I need to reinstall the "recording and monitoring utility" but I can't find this to be downloaded ??? 
    Thanks for any help !
    D

    ok, never mind. 
    I found that this one is included in the "setup wizard" (http://www.linksysbycisco.com/NL/nl/support/WVC54GCA/download)

  • My MBP Retina doesn't allow the use of two Thunderbolt to DVI adapters. It only works with one TB - VGA adapter and one TB - DVI adapter. However now the color on the VGA connected monitor is slightly different.

    The monitors are Viewsonic VA2406m-LED. The Display preferences show all three monitors but one monitor always says "No Signal" if they are both connected TB -> DVI.
    The Color on the VGA connected one is slighly off. It seems like I should be able to connect two DVI monitors not sure why this is stopped. Does it have something to do with the Graphics card?

    The problem was with the newEgg adapter. I just went to the Apple Store and bought an Apple adapter and the monitor now displays correctly.
    For future reference, in case anyone experiences this problem:
    the newEgg adapter is part number 9SIA1PU0P88920, described as a Thunderbolt Mini Displayporrt Display Port DP to DVI Adapter for APPLE Macbook Pro Air and the full description says it works for macbook pro, etc.
    when this adapter is used, the macbook pro recognizes the monitor, but the monitor displays nothing.
    When the apple adapter (MB507Z/B Mini Display Port to DVI Adapater) is used, the monitor displays correctly.
    Of course, the individual newEgg part might simply be defective, but I doubt it.  moral -- spend the extra $$ and buy the Apple adapter.

  • I have a 15in MBP late 2013 w/ Mavericks installed.  At work, I was hoping to dock the MBP and connect to dual Dell P2414H monitors.

    To do so I purchased (2) DisplayPort to HDMI cables and (1) Thunderbolt to HDMI adapter.  As for setup, I have one monitor directly connected to the HDMI port on the MBP and the other monitor connect to the Thunderbolt adapter. 
    I am getting no signal whatsoever on either monitor.  I've ensured that each monitor is set to DisplayPort.  I can understand a signal issue existing between the monitor and the adapter, but I cannot understand the issue with the monitor connected directly to the MBP via the HDMI port.  I checked System Report > Hardware > Thunderbolt and my Thunderbolt to Ethernet adapter shows, but port2 contains no connected device (this is where the Thunderbolt to HDMI adapter is plugged).  Does anyone know where I can check the status of the HDMI port?
    I'm hoping that the issue isn't as blunt as the monitors not being compatible with the MBP.  I've used my previous MBP with another, older, Dell monitor via a Thunderbolt to VGA adapter with no issue whatsoever.  I've scoured the interwebs with the hopes of finding someone with a similar issue, but I've found nobody.

    When the dock is defined as on the bottom, it will appear on the screen of the extended desktop that is lowest.
    Move the second monitor where the bottom edges are equal or the Dell is lower and the dock will move there.
    Regards,
    Captfred

  • I have a new MAC MINI and I want to install a second monitor.  I have one connected to the HDMI and it works.  I can't get a signal to the other one.  It is connected from the thunderbolt to its HDMI port.  How can I make it work?

    I have a new MAC MINI and I want to install a second monitor.  I have one connected to the HDMI and it works.  I can't get a signal to the other one.  It is connected from the thunderbolt to its HDMI port.  How can I make it work?

    Could be a bad cable or bad Thunderbolt port.
    You have 90 days of free telephone support on a new device. You can call them at 1-800-MY-APPLE. Have your Mini's serial number handy
    You can also make an appointment at the Genius Bar of an Apple store.
      Apple Retail Store - Genius Bar

  • The monitor on my macbook is turned off while I was working, I could not in any way to do it again, I could see through the screen off the open pages I was working on, I had to turn off the machine and restart it. and it runs. O.O?

    The monitor on my macbook is turned off while I was working, I could not in any way to do it again, I could see through the screen off the open pages I was working on, I had to turn off the machine and restart it. and it runs. WHAT 'success? The report says the console like this: (at approximately 12.30)
    No receipt for 'com.apple.pkg.JamPackWorldMusicInstruments' found at '/'.
    03/05/11 12:08:30 [0x0-0x1e01e]. Com.apple.garageband [239] No receipt for 'com.apple.pkg.JamPackWorldMusicInstruments' found at '/'.
    03/05/11 12:08:30 [0x0-0x1e01e]. Com.apple.garageband [239] No receipt for 'com.apple.pkg.JamPackOneInstruments' found at '/'.
    03/05/11 12:08:30 [0x0-0x1e01e]. Com.apple.garageband [239] No receipt for 'com.apple.pkg.JamPackOrchestralInstruments' found at '/'.
    03/05/11 12:08:30 [0x0-0x1e01e]. Com.apple.garageband [239] No receipt for 'com.apple.pkg.JamPackRhythmSectionInstruments' found at '/'.
    03/05/11 12:08:30 [0x0-0x1e01e]. Com.apple.garageband [239] No receipt for 'com.apple.pkg.JamPackRemixToolsInstruments' found at '/'.
    03/05/11 12:08:32 MIDIServer [255] MIDIServer [255] starting; arch = i386
    03/05/11 12:34:35 com.apple.launchd [1] *** launchd [1] has started up. ***
    03/05/11 12:35:06 com.apple.launchd.peruser.501 [86] (com.apple.ReportCrash) Falling back to default Mach exception handlers. Could not find: com.apple.ReportCrash.Self
    03/05/11 12:35:09 com.apple.launchd.peruser.501 [86] (com.apple.Kerberos.renew.plist [110]) Exited with exit code: 1
    03/05/11 12:35:25 [0x0-0xd00d]. Com.skype.skype [127] WirelessAttach: IOServiceOpen error: e00002c7
    03/05/11 12:35:25 [0x0-0xd00d]. Com.skype.skype [127] WirelessAttach: IOServiceOpen error: e00002c7
    03/05/11 12:35:26 [0x0-0xd00d]. Com.skype.skype [127] WirelessAttach: IOServiceOpen error: e00002c7
    03/05/11 12:35:26 [0x0-0xd00d]. Com.skype.skype [127] WirelessAttach: IOServiceOpen error: e00002c7
    03/05/11 12:35:32 [0x0-0xd00d]. Com.skype.skype [127] WirelessAttach: IOServiceOpen error: e00002c7
    03/05/11 12:35:33 [0x0-0xd00d]. Com.skype.skype [127] WirelessAttach: IOServiceOpen error: e00002c7
    03/05/11 12:35:33 [0x0-0xd00d]. Com.skype.skype [127] WirelessAttach: IOServiceOpen error: e00002c7
    03/05/11 12:36:06 com.apple.WindowServer [64] Tue May 3 12:36:06 MacBook-Pro-17-of-Admin.local WindowServer [64] <error>: kCGErrorFailure: Set a breakpoint @ CGErrorBreakpoint () to catch errors logged as They Are.
    03/05/11 12:43:39 helpd [160] Response failed Because Listener can not find a port for this QueryID.
    03/05/11 12:43:43 helpd [160] Response failed Because Listener can not find a port for this QueryID.
    03/05/11 12:43:43 helpd [160] Response failed Because Listener can not find a port for this QueryID.

    Do you have backups of all the data on the startup drive? If not, do nothing else until you've backed up that data, if you still can.

  • Drop ship line did not split, the material have partial receipts, can the PR and PO be canceled?

    hello,
    I need some help with this issue. We have a drop ship line that have 270 cartons in status awaiting receipt, but in the inventory already received 624 cartons.  The line of that sales order needs to be closed now, to invoice the customer. But the PR and PO looks like OPEN.
    I tried to manually split the line in the sales order. To have two lines; one with the 624 already received, and other one for the 96 cartons left. But an error message shows when i do this.
    The error its :  You are not allowed to split Order Line because:Line is released to purchasing
    I found in the ORDER ORGANIZER when i chek the Sales Order, the ORDER SOURSE LINE REFERENCE the last line (which suppose to be splitted with the reception of the material) have a number lower than the line before it.
    example: line 2.5 have OE_ORDER_LINES_ALL27231981  and line 2.4 OE_ORDER_LINES_ALL27232315
    Can somebody help me with this?
    i also found a bug in meta link but i think something can be done. bug 2281449.
    Thank you,
    Paloma Cadena

    We had similar issues in the past. We solved them by doing a mini customization.
    The customization created an short-text attachment of the type "Note to receiver" at the PR level. The attachment included the Sales order # and line#.
    This attachment flows from the PR to PO and is also available to the receiving clerk during receipt.
    However, once the PO is received, we did not transfer the information to onhand. I don't think one can unless the item was serialized or lot controlled.
    Hope this helps,
    Sandeep Gandhi
    Independent Techno-functional consultant

  • What is the best product for network mapping and monitoring? I am an inexperienced user). Mac 10.9.2 laptop

    I have lots of questions, but the gist is that I want to know the best product, preferably from the app store, that I can use for network mapping mapping and monitoring.
    I want to get their mac address or other police trackable etc info so I can use my computer safely.
    I am also being cyberbullied.
    I try just using ethernet but still get intruded on, for instance, messages that "other devices are using my ip address". The only other device I own is an iPod that I keep sahut off plus wifi turned off then.
    (NOTE:  You can skip the rest of this message if you want. It regards hacking attempts etc,  a little out of the scope of discussion, perhaps).
    Also a home intrusion where computer was thoroughly hacked with router(s) set up "very very close to me," according to Apple.
    Also, hackers get into my Facebook and gmail and yahoo mail, really,  no matter what I try to do on my computer and how many times I change passwords it does no good.
    Also,  The ip addresses for google and the one in syste preferences and the one looking up my ip address on ip chicken always gets three different results.
    More worrisome it that hackers got into my Wells Fargo account a week after the intrusion even though I changed all account #'s and pw plus notified bank. They also broke into paypal using my new account numbers.
    Also, stuff like Facetime pops up on my computer without my clicking on it even though I'm using ethernet to connect. I've given up on Time Capsule because I'm told that's how the hackers hacked my computer so thoroughly duriung the intrusion.
    Thanks.

    Aubry,
    why don't you send your sequences straight to Compressor first, encode your movies as MPEG 2 and AC3 audio and import all assets in DVD studio PRO?
    G.

  • How do I record AND monitor at the same time?

    I'm having trouble while trying to record from my XLR connected microphone. I have the mic going through a USB preamp and my speakers are outputting directly through my Power Mac. I cannot seem to be able to record at the same time I monitor. I can't playback my recordings without first changing the audio setting to Built in Audio from Mobile Preamp. I swear I could do this with Logic 7. Can't I have the monitor be going through the computer and the input going through my preamp at the same time? Thanks!
    Appi

    Logic can see two or more audio interfaces at once, but it has to be set up in the Audio midi set up program on your mac, as an aggregate device using your built in audio and your USB device. Then you can choose the aggregate device in your Logic>preferences>audio>driver. After you choose it, you should be able to access all inputs and outputs at once
    Don

  • Hello, I have a Mac computer with NVIDIA 750M dedicated graphics card and monitor EIZO but the problem was there when I was working with Windows and Acer monitor. When I open a file from Camera Raw in PS this is smaller than the screen so I double-click w

    Hello, I have a Mac computer with NVIDIA 750M dedicated graphics card and monitor EIZO but the problem was there when I was working with Windows and Acer monitor. When I open a file from Camera Raw in PS this is smaller than the screen so I double-click with the tool "hand" to fit on the screen, but the picture loses sharpness and becomes blurry. If you magnify the image even only slightly with the tool "zoom" the picture comes back clear. In Camera Raw instead is always sharp. I solve the problem by turning off the graphics card in PS but often use plugin that need the graphics card otherwise the processing time is much longer. I ask for help.
    Thanks.

    Hello, I have a Mac computer with NVIDIA 750M dedicated graphics card and monitor EIZO but the problem was there when I was working with Windows and Acer monitor. When I open a file from Camera Raw in PS this is smaller than the screen so I double-click with the tool "hand" to fit on the screen, but the picture loses sharpness and becomes blurry. If you magnify the image even only slightly with the tool "zoom" the picture comes back clear. In Camera Raw instead is always sharp. I solve the problem by turning off the graphics card in PS but often use plugin that need the graphics card otherwise the processing time is much longer. I ask for help.
    Thanks.

Maybe you are looking for

  • Printing more than one photo on a piece of 8x10 paper.

    How do I get multiple photos on a piece of 8x10 paper so the photos are siazed to fill up the 8x10?

  • Can't create engine: a new feature with Java Plug-in 1.6.0-beta2 ?

    Hi We use Java.Help embedded in an applet to check small pieces of text. The whole things works without problems until recently: the full text search does not work anymore when the applet is called with http, it does work when it is called as File in

  • Determine the type of the caught exception

    Hi! Here is my problem : I'm using a web service and the method I call throws different types of Exception (RemoteException, ServiceException, etc...) And, the reaction to the caught exception depends on its type, that's why I need to determine what

  • Help installing Java on Windows XP Embedded (XPe)

    I'm trying to deploy an embedded system running Windows XP Embedded. The application we need to run on it is written in Java and i'm having a heck of a time getting Java to work on XPe. Basically i'm building my OS image and then copying my Java Runt

  • Retina iPad or iPad mini ? A tough decision...

    Well, I guess a lot of people might have asked this question before, though I did not take the trouble to check. I have a 11" MacBook Air and an iPhone 4, and an iPad is obviously what is missing in-between. I need an iPad to read newpapers and magaz