Should the Airport be turned off when not in use?

Yes Or No, on or off?
mp

There has always been two equally divided camps when it comes to leaving electronic equipment running 24x7 or powering-off. I think it really depends on what your requirements are for the base station.
The AEBSn draws about 22 watts of power when running, about the same as a low wattage incandescent light bulb ... and puts out about the same amount of heat.

Similar Messages

  • Should Wireless Router be turned off when not in use?

    I successfully installed the Linksys Wireless G Broadband Router Model WRT54G.  It was very easy.
    I notice that it now appears to be "on" all the time, and I use my home PC & Laptop perhaps up to about only 2 hours a day.  Should I be turning it off when not in use?  Is it a potential security risk to always have it on?  If I do turn it off, is the only way to unplug the power adapter?  I can not locate any on/off button on the router.
    Thanks,
    Adam  

    You said your router was "very easy" to set up.  I hope that this does not mean that you skipped setting up security.  If your wireless router is not secured, having it on or using it is a security risk.  If your router is secured, then it is OK to leave it on 24/7.
    If your wireless is not secured, anyone in the area can log into your router and use your DSL line.  At a minimum, this wastes your bandwidth.  At a maximum, someone could send spam, visit child porn sites, distribute viruses, and give away copyrighted music  ---  all from a DSL account with your name on it!    Additionally, if your router is not secured, others can see what you are doing on the net, including seeing your bank account numbers, passwords, and credit card numbers.  So my advice is ... secure your system.
    In order to keep intruders off of your wireless system, you need to enable wireless security.  To do this, pick an SSID and don't broadcast it.  Encrypt your wireless system using the highest level of encryption that all of your wireless devices will support.  Common encryption methods are:
    WEP - poor  (see note below)
    WPA - good
    WPA2 - best
    WPA and WPA2 sometimes come in versions of "personal" and "enterprise".   Most home users should use "personal".  Also, if you have a choice between AES and TKIP, and your wireless equipment is capable of both, choose AES.
    The wireless devices (computers, printers, etc.) that you have will need to be set up with the SSID, encryption method, and passwords that match those you entered in the router. 
    For additional security, on many routers, you can limit wireless access to just the MAC addresses of the wireless devices that you own.  If possible, you should definitely use this feature.
    And don't forget to give your router a new login password.
    Also, when you pick your login password, SSID, and encryption key (or password or passphrase) you should use a random combination of capital letters, small letters, and numbers.  An SSID, or a login password, should be 12 characters or more.  WPA and WPA2 passwords should be at least 32 characters.
    Note below:  Recently the FBI demonstrated that WEP can be broken in under 5 minutes using standard, internet available, cracking tools.  This suggests that virtually all wireless users should upgrade their wireless equipment to WPA or better.
    Message Edited by toomanydonuts on 12-22-200601:05 AM

  • Upgraded Cloudon ..now backlight does not auto turn off when not in use.  How do I do that

    Upgraded Cloudon.  Now the backlight does not turn off when not in use.  How can I correct this. Using iPad 1sted

    Is your question for a MacBook Air like your profile says ? You're in the iPad Forum, I could ask the hosts to move your question.

  • How  long to leave plugged in to charge ipad mini? should ipad mini be powered off when not being used for a long period of time (several hours between usage times? Please respond this ipad mini is new and I would like to keep it in good condition.

    How long should you leave an ipad mini plugged in to charge? How low should the battery be? Should I power it down when I am not going to be using it for several hours between uses? Thank you. I NEED to know these things.

    About iPad Batteries  >  http://www.apple.com/batteries/ipad.html
    ssutton709 wrote:
    How long should you leave an ipad mini plugged in to charge? How low should the battery be?
    Charge it when you see the Low Battery Alert. It is not recommended to Fully Discharge the battery.
    Use Your iPad Regularly
    For proper reporting of the battery’s state of charge, be sure to go through at least one charge cycle per month (charging the battery to 100% and then completely running it down).
    ssutton709 wrote:
    Should I power it down when I am not going to be using it for several hours between uses?
    This is not necessary.
    Most importantly... Enjoy your iPad

  • Modem Setup Says Airport is Turned Off When It's Turned On

    I'm trying to set up a new modem/wireless account using Motorola 2247-N8. During the se- up phase it keeps telling me that the AirPort is turned off, when in fact it's turned on and can pick up many wireless networks in my vacinity. This problem keeps kicking me out of the set up phase so I can't even set up the new network. I go into System Prefrences>Networks and the AirPort is there with a green light. What is the problem?

    If your MacBook (MB) is able to "see" and connect to other Wi-Fi networks then chances are the AirPort card built-in the MB is not the issue.
    By default, your Motorola Netopia gateway device has a local (LAN-side) router IP address of: 192.168.1.254. Your MB will need to be on this local network in order for it to find it. This may require that you temporarily reset your MB to using an IP address, like 192.168.1.100. You can do this via System Preferences > Network > AirPort. Easier still I would recommend that you temporarily connect the MB to the Motorola using an Ethernet cable. The Motorola should assign the MB the proper IP address and you should now be able to access the Motorola's web-based administrator interface.

  • Apple TV powers off when not in use

    My Apple TV turns off when not in use and needs to be rebooted by unplugging device to "wake" it up  How do I avoid this?

    All ATVs go into sleep mode when not in use.
    Simply pressing the power button on the remote should wake the device up, is that not occurring?

  • I'm sure your'e going to tell me I just need a new phone but maybe there is hope for my iphone 4.  It will not charge past 66% (it's not the charger), it turns off when unplugged, and it will not even let me turn my wi fi to the on possition.  Help!

    'm sure your'e going to tell me I just need a new phone but maybe there is hope for my iphone 4.  It will not charge past 66% (it's not the charger), it turns off when unplugged, and it will not even let me turn my wi fi to the on possition.  Help!

    Hi there 8472kck!
    I have some information for you that can help you troubleshoot this issue a little further. That information can be found right here:
    Will not turn on, will not turn on unless connected to power, or unexpected power off
    Verify that the Sleep/Wake button functions. If it does not function, inspect it for signs of damage. If the button is damaged or is not functioning when pressed, seek service.
    Check if a Liquid Contact Indicator (LCI) is activated or there are signs of corrosion. Learn about LCIsand corrosion.
    Connect the iPhone to the iPhone's USB power adapter and let it charge for at least ten minutes.
    After at least 15 minutes, if:
    The home screen appears: The iPhone should be working. Update to the latest version of iOS if necessary. Continue charging it until it is completely charged and you see this battery icon in the upper-right corner of the screen . Then unplug the phone from power. If it immediately turns off, seek service.
    The low-battery image appears, even after the phone has charged for at least 20 minutes: See "iPhone displays the low-battery image and is unresponsive" symptom in this article.
    Something other than the Home screen or Low Battery image appears, continue with this article for further troubleshooting steps.
    If the iPhone did not turn on, reset it while connected to the iPhone USB power adapter.
    If the display turns on, go to step 4.
    If the display remains black, go to next step.
    Connect the iPhone to a computer and open iTunes. If iTunes recognizes the iPhone and indicates that it is in recovery mode, attempt to restore the iPhone. If the iPhone doesn't appear in iTunes or if you have difficulties in restoring the iPhone, see this article for further assistance.
    If restoring the iPhone resolved the issue, go to step 4. If restoring the iPhone did not solve the issue, seek service.
    and that information comes from this article:
    iPhone: Hardware troubleshooting
    http://support.apple.com/kb/TS2802
    Thanks for being a part of the Apple Support Communities!
    Regards,
    Braden

  • Should I shut down my computer when not in use

    should I shut down my computer when not in use, overnight for instance?

    Hello! Leaving it on 24/7/365 is perfectly acceptable. You may save some electricity but personally I think you'll pay for it with a more troublesome system. I do however set the monitors to go to sleep. I like the no startup lag time of running 24/7/365. That said, if I lived in an area prone to electrical outages or if my location was prone to lightening strikes I'd probably shut it down and unplugged. Of course with it being unplugged the pram battery may run down. These old G4's have been running 24/7/365 for years now. I do try to restart every few weeks just for good measure! In the end it's your preference. The hardware works best when a constant temperature is maintained. Tom

  • Should AX be unplugged at night when not in use?

    ,

    FlexSF wrote:
    Should AX be unplugged at night when not in use?
    i'm using my two AX units for streaming content and have been unplugging them @ night for years - with not adverse effects so far.
    i also believe this will help save a little energy ...
    JGG

  • HP Officejet 6500a Should I turn it off when not in use?

    Is it better too turn off the printer when not in use for short periods say 2-4 hours? or days? (the manual does not explain this adequately) Thanks

    Hi,
    I normally turn my printers off to save few cents of electricity. No point to keep printers on unless you are having/doing business (expecting fax or something). Even at work, for a long weekend, we always turn our printers off.
    Regards.
    BH
    **Click the KUDOS thumb up on the left to say 'Thanks'**
    Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.

  • How do I tell Apple to fix their software like apps that play sound even though the sound is turned off and not being able to disable features you hate like game center

    Apple is suppose to be the pinnacle of usability and, yet, I want to throw my new IPhone 4s as far as I can and watch is smash into a million pieces on concrete. Seriously, I've already got three things that irritate the **** out of me. First, there are Apple apps that insist on playing sound even though the sound is turned off. If I flick a switch to turn the sound off, I want the sound off!!!! Second, if I do not want a totally unnecessary feature like Game Center, I should be able to disable it. I completed most of the Angry Bird levels with 2 or 3 stars and now I have to start over from square one. Maybe, this happened when I upgraded to the 4s but it sure seemed to happen when I joined Game Center. Tomorrow, I am going to reset my 4s to factory defaults to try to get rid of my Game Center account. I don't want Game Center! I do need Game Center! I hate Game Center! Finally, I had an alarm go off to wake me up and there was a Snooze button but no button to turn the alarm off. I flicked the slider to access the main screen expecting to see something to turn the alarm off but there was nothing. The alarm just kept alarming. I had to warm boot my IPhone to shut the alarm off! Really, Apple!!!!

    The sound is turned off. Only, some Apple apps like YouTube and Siri make sound when the sound is turned off. It is very embarrassing when this happens at work. My question was how do I tell Apple to fix this?
    Turning off game center does not work. The games just prompt me to sign in when they are started.I have tried everything I can find online to stop this behavior. It is annoying and should not happen. My question was how do I tell Apple to fix this?
    The alarm went off. There was a green thing that looked like a button but pressing it did nothing. There was a red button that said snooze. I did not want to snooze. I wanted to turn the alarm off. I slid the bar to unlock the phone and there were no running apps with a button to press. The alarm just keep running. I have not had this problem since it first occurred. The alarm now shuts off when I just unlock the phone. It may have happened because I had another alarm app running. The two may have interfered with each other. I would like to tell Apple about it.
    It also annoys me that the button that closes apps leaves the phone app running. If I press on a number at 6:00 AM to get information about who called me, the phone automatically dials the person back and my natural reaction is to press on the button to close the phone app but the phone keeps dialing this person at 6:00 AM. It is a bad design. I would like to tell Apple about it.
    Finally, I looked all over Apple's site to try to find someplace I could send them a polite message to let them know that I was not happy with these "features" but could not find anything. It is extremely frustrating to have issues with a product and not being able to tell the manufacturer about it. So, you grow up!.
    When trying to fix the Game Center issue, I saw a link someone posted to report issues with the IPad to Apple. The answer I am looking for is where is the link to report issues with the IPhone.

  • I have lost my iphone and the power was turned off when i lost it and i dont have find my iphone installed what can i do?

    I have lost my iPhone 4s and i had it turned off when I laid it down somewhere and I have not installed the find my iPhone app. Is ther anyway possible to locate it.

    Nope.  If you didn't have find my iphone turned on, you will not be able to locate it.  File a police report, and contact your carrier.
    http://support.apple.com/kb/HT5668

  • The iPhone 4 turns off when I receive or make voice calls

    My iPhone 4 turns off when I receive or make voice calls...
    The problem occurs several times a day, but not all the time i make or receive calls
    I already tried several times to restore the iPhone as "new device " but the problem persists.
    Someone has already met and eventually solved this problem?
    I cordially greet and thank in advance

    I'll try to do that! Thanks again

  • Switch off when not in use or standby?

    I dont have an ATV yet, but have lots of questions!
    When not being used, is the ATV to be left in standby (consuming what I hope is just a small amount of electricity) or can the power be turned off at the wall socket? Does it lose any settings if I do this? I only have time to watch TV at weekends.

    There is a stand by mode but it isn't a very low power mode, if you only use the tv at weekends, I would unplug it in between. I'd usually say don't be unplugging it regularly, but I don't believe once a week is. Personally I'd leave the unit in stand by on Saturday night though.

  • My mac powers off when not in use and I must unplug to restart.

    My Mac powers of after not being used for a period of time.  I must unplug to restart.

    All ATVs go into sleep mode when not in use.
    Simply pressing the power button on the remote should wake the device up, is that not occurring?

Maybe you are looking for

  • How do I access an external hard drive attached to an Airport Extreme using the Finder's "Go to the folder" feature?

    How do I access an external hard drive attached to an Airport Extreme using the Finder's "Go to the folder" feature? I have an external hard drive attached to my Airport Extreme and I can access it just fine through Finder.  I would like to be able t

  • Error in xml file validating to xml schema

    Hey, I am getting the following error while validating xml file to its schema: The error is: SAMPLEITEMDLFILE.xml:2,139: no declaration found for element 'WMWROOT' The XML document SAMPLEITEMDLFILE.xml is NOT valid (1 errors) schema file: <?xml versi

  • Max User Defined Table Size

    What is the maximum supported size for a SBO UDT?  I have a table that has about 2 million rows in it.  Making updates to this table through the SDK fails except for when I clear all rows from the table in a test environment.  Thank you!

  • Calling DCE RPCs from Forte

    Hi all, We are considering the use of DCE RPC with Forte. I know that it is possible to both call-in and call-out to DCE from Forte, and we are primarily interested in calling out, i.e. presenting an existing set of DCE RPCs as methods in a virtual F

  • Rating Widget and Notifiers/Observers

    Hello, I am trying to figure out how to get a rating widget to update as the user clicks on spry:setrow images. I believe I need an observer and notifier but not sure what comes first. I have multiple image galleries and need to have rating rate the