Sin wave generation for R series FPGA

Dear All,
I am generating sin Wave with (FPGA Sin Wave Generation Express vi) from Rseries FPGA Target.Frequency range is from 1500Hz to 3000Hz.Frequency and Amplitude parameters are coming from Host .Wave is going to an AO.The wave is not displaying in my Host with the set parameters as required.
What am I doing wrong??
Certified LabVIEW Architect
Certified TestStand Developer

Hi,
I am using NI 9263 4x AO.the problem was with the FPGA Express vi Parameters used the example sin wave Generation from the FPGA fundamental folder and modified the Host parameters to meet our requirement and it worked fine.
Thanks
Certified LabVIEW Architect
Certified TestStand Developer

Similar Messages

How to generate finite cycles of sine wave using daq mx in vc++

Hi,
How to generate finite cycles of sine wave or for finite duration in vc++ using hardware timer without any sleepfunction in the code.
Thanks & Regards,
satya

Hello Elizabeth,
Thanks for the response.
1) I am using NI 6040E PXI.
2) I am using NI-DAQMx 8.3
3) Measurement Studio is 6.0.0.105
4) Operating system is Windows XP.
I want to generate sine wave for finite duration previously in traditional daq there was function called wave_op.In which we can mention number of cycles of sine wave we wanted to generate. That function is not available in DAQMx so we have to use sleep function to generate finite period. Any hardware control function to control generation of finite cycles please let me know.
Thanks & Regards,
satya

Sine wave on startup

I searched for this all over and can only find references to start up sounds like 5 beeps or breaking glass.
A couple of times I have started up my PowerBook G4 to have it make a single mid-ranged sine wave sound for a second or so. Then it waits for a few seconds and makes the normal startup sound. Everything seems to be running fine, except that hard drive access has become pretty slow. I tried running repair disk and it did nothing. What does the sine wave sound signify? Like I said this has only happened a couple of times, and is the only unusual error I've gotten.
Thank you,
Andrew
PowerBook G4 17" Mac OS X (10.4.8)

sometimes slow drive access means failing hard drive.
all kinds of noises could be made by failing drives also.

I want send sine wave to Excel sheet.

How are you?
I want send sine wave in for loop to excel sheet when end the program??
How can I do this?
notice : I have virsion 8.5
Attachments:
project 1.vi ‏193 KB

duplicate post

How can i do a sine wave with High Throughput Sine for fpga?

I try to do a sine wave looking the examples but i can't. I have a sbRio 9606.
I need to do a sine wave with high throughput block. In my exercise i have 2 inputs (amplitude and frecuency) and i have to look the output (sinewave)
I need help!!

Hi pablosan,
If I understood correctly, you want to generate a sine wave with a high throughput block in Labview FPGA.
I'm afraid you won't e able to do this, as these blocks are specifically designed for other FPGA targets with better features for high performance. So instead of using the example named "Sine and Cosine.lvproj" under High Throughput examples, you can use the "Sine Wave.lvproj" under Signal Generation and Processing examples, which is more adequate to your Single-Board RIO.
Regards.

How can I get 'sync' signals for sine wave out? [FPGA USB 7856R]

Hello,
I'm Sean Ahn using NI 7856R, USB FPGA with LabVIEW 2014.
I'm trying to make 'sync' signals for sine wave of adjustable frequency, like general function generator's sync out.
I use sine waves whose frequency is feedback-congtrolled between 25~30 kHz and need sync signals of square wave.
Like [1] below, when I try resettng two wavefom-generators, sine and sync signals are not perfectly synchronized.
And everytime I adjust sine's frequency, the phase difference between sine and sync changes arbitrarily
In case of [2] using 'zero-crossing detector', I have severe jitter of sync signals not suitable as 'sync' signals for other parts.
Please, give me some help.
Thanks in advance
Sean Ahn
[1] Reseting two waveform generators
[2] Zero-crossing detect

Here’s my issue. When I try to move any data between my PC and the iPad2 I receive an error message that states that “the [sync] session could not be started with the ipad, Please disconnect and reconnect the iPad and try again”
I have tried again and again by various methods etc . and all I get is the same message when I attempt to sync, backup or update the iPad.
I have tried the following AND FAILED:
Deselect all Apps, Music etc in iTunes, then attempt to sync
Disable and enable the iPad in device manager and restart itunes and try to sync again
Disable and enable Apple Mobile Device Services and sync/backup/update
Run iTunes as Administrator
Reboot all devices (iPad buy pressing two buttons at once)
Turn off all security and reboot and sync
Connect directly to internet without a router
Tried to sync with all wireless turned off and in airplane mode
Running iTunes Diagnostics...... nothing all test passes
Changing USB ports and cables
Removing my SIM card and rebooting and trying to syc
Trying to sync via wifi only
Turning off all icloud services
Uninstalling all Apple Software and reinstalling again
I am syncing to a 64bit PC running Win 7 Premium with all the latest updates, all firewalls off. WiFi and direct connect ethernet to Internet service with and without router.
I am trying to Sync an iPAD 2 running iOS version 5.1.1 (9B206)
I am trying to update from iOS 5.11 to 6.01 by using Itunes 11.0.0.16.3 in a USB or directly through the iPad via wifi.
Please help as everything I have tried has failed.

I am trying to generate a 50kHz sine wave for ten cycles, then aquire this waveform and store it in a file, I am using a PCI-Mio 16E-4 board, has anyone done anything like this?

I am trying to generate a 50kHz sine wave output on the DAQ card and then simultaneously recieve. I am using a PCI-Mio 16E-4 series board to do this. Has anyone done anything similar. I can generate a 50k wave no problem, and recieve one, but I can not get these vis to run together? Any suggestiosn

Jrod, yes you should be able to do this, actually there are quite a few example programs come with LabVIEW that handles simultaneous analog input and output, I check the specs of the board you use, the board should be able to handle the sampling/generation rate, but make sure for 50KHz sine wave, you would sample at least twice as fast, preferably ten times the generation rate, then this puts the sampling of the board to thew limit.
The program you can try is attached here, good luck with the application,
XD Gao
Applications Engineering,
National Instruments
Attachments:
Simul_AIAO_Buffer(E-series).vi ‏104 KB

Générer une implusion avec "Sine Wave Generator" en FPGA

Bonjour,
Content de vous rejoindre sur ce forum. Tout nouveau en Labview (pas très à l'aise avec certaines notions), je voudrai soliciter votre aide. En fait, je veux créer une impulsion de 100Hz avec la fonction " Sine Wave Generator" de FPGA. En simulation j'ai réussi mais dès que je compile en target il m'affiche ce message : "Top-level clock rate does not match rate for which the Sine Wave Generator VI was configured. Reconfigure the Sine Wave Generator or the top-level clock so that their rates match. You also might need to modify computed values for the frequency (cycles/tick) input."
Je change donc FPGA clock rate et je choisis 40MHz (la seule qu'il me propose). Mais dans ce cas, je me perds pour retouver mon impulsion (qui doit durer une période 0.01sec). J'ai essayé de jouer sur le nombre d'échantillons en changeant le nombre d'itérations de la boucle For afin de générer toujours une période ( pièces jointes) mais ça marche pas!!!
Pourriez vous m'aider à déchiffrer ce problème?
Merci d'avance
Pièces jointes :
burst sine.png ‏372 KB
burst sine_40MHz.png ‏336 KB

Bonjour M2IM,
En mode simulation, on utilise une fonctionnalité appelée "Interactive Execution" car l'exeuction/affichage ne peut être géré à une fréquence élévé (40 MHz dans le cas de la Top Level Clock par défaut).
En mode FPGA target, la vitesse est plus élevé et donc uniquement certains points du sinus seront afficher mais le signal electrique lui sera bien un sinus.
Je t'invite à regarder le lien ci-dessous qui reprend quasiment la problématique que tu rencontres:
Generate a sine with LabView FPGA and connect it to an AOModule
Bonne journée,
Valentin
Certified TestStand Architect
Certified LabVIEW Developer
National Instruments France
#adMrkt{text-align: center;font-size:11px; font-weight: bold;} #adMrkt a {text-decoration: none;} #adMrkt a:hover{font-size: 9px;} #adMrkt a span{display: none;} #adMrkt a:hover span{display: block;}
Travaux Pratiques d'initiation à LabVIEW et à la mesure
Du 2 au 23 octobre, partout en France

How to generate a continuous sine wave for a given amount of time

I am trying to output a continuous sine wave for a speaker, but I am having difficulty making it continuous rather than looping the signal for a given amount of time, which causes discontinuities. There is a VI in the Labview examples titles Continous Generation, but it produces a square wave. Is there a way to adapt this VI such that the amplitude and frequency can be used as inputs to create a sine wave?

I found a VI that ships with labview(7.0)called continuous sound output. the output of this is a sine wave or you can change it to whatever you want.
Sorry cannot help more
Joe
Joe.
"NOTHING IS EVER EASY"

How to dynamically adjust Frequency, Phase and Amplitude for a Generated Sine Wave in C/C++?

Hi,
I wonder if anybody know how to dynamically adjust Frequency, Phase and Amplitude for a Generated Sine Wave in C/C++? This is a part of my project: I need to dynamically generate a sine wave voltage signal by some calculation using the data from a simultaneous analog input and another signal.
Your help will be appreciated so much!
Marlon

Hello Marlon,
Here is an example of changing frequency and ampliude for an E-series device in Labwindows/CVI. The programming should be similar in C for your S-Series device. As is says on the linked webpage above, this process is going to be very processor intensive since you will continually be creating a buffer.
Nicholas C
National Instruments
Applications Engineering

Best fit lines for loops and sine waves

I am trying to find a best fit line that will work for sine waves and loops (hysteresis loops). I can get the sine wave just fine, but when I switch to a hysteresis it just puts a line across the middle (I assume because of the 2 y values for every x). I am doing data acquisition that will take in both forms and graph them. I tried a polynomial fit and it doesn't work at least the way I implemented it and I tried a few others but it looks like they are all function based. Also, my y values are coming out of a Bessel filter. I don't think this would be affecting anything but I thought I would put it in here incase it does.
Did I miss one that I haven't tried that works for my application?
Thanks
Patrick

RiversDaddy wrote:
... currently I am doing it by looping and reducing the error towards zero to fit the amplitude and phase. (I know the frequency). If this is what you are looking to do then I will help, or should I be doing things differently? All of the functions I have found to filter or extract tones seem to introduce a larger frequency of phase error than i get using this method, but am I missing something?
"looping" is a bit vague. What is the actual algorithm to find better estimates (e.g. levenberg marquardt, etc.)
What problems did you have with extract single tone. Can you show some data where the results from it are not good?
LabVIEW Champion . Do more with less code and in less time .

LabVIEW FPGA Sine Wave Generator Reset Input Behavior

I would like to know what the output from the Sine Wave Generator express VI is while the reset input is true, and what happens to the output immediately after the reset input is set false.
I need to generate a regular sequence of positive half-cycles of a sine wave, with an arbitrary delay between them that is not related to the actual frequency of the sine wave. So my plan is basically to periodically fire a trigger in the fpga software that resets a sine wave generator and directs its output to an analog output until the sine wave goes negative, at which point the analog output is set to 0 until the next trigger.
Thanks

Muchas gracias por responder steve.bm
El problema que tengo es el siguiente, estoy desarrollando un proyecto en el cual uso los conversores DAC y ADC de la tarjeta FPGA Spartan 3E para lo cual use como base el proyecto que esta subido por la NI que se encuentra en uno de los enlaces que me dejaste,( Lesson 8 - Linking Existing VHDL Code from WebPACK into LabVIEW FPGA) del mismo solo modifique para usar el ADC y el DAC mediante el cual adquiero una señal senosoidal y la tengo que reconstruir, el problema es que como uso un generador de señal de laboratorio al ingresar la frecuencia de muestreo para obtener una buena reconstruccion, la frecuencia se baja lo cual en el proyecto real no podra pasar ya que la frecuencia ya en proyecto final la adquiero de la red electrica publica pero ahora para pruebas estoy con un generador, la verdad no se que pasa porque tiene un retrazo la señal.....
Te parece si te puedo dejar mi proyecto subido en enlace para que lo revices ??

FPGA sine wave generator

NI工程師你好
我在FPGA端使用sine wave generator
可是出來的波形卻不是一個完整的Sin波圖形
可以請工程師幫我解答一下嗎??
已解決！
轉到解決方案。
附件:
sin.png ‏10 KB
sin-1.png ‏13 KB

好吧，我認為問題可能是您使用的圖表上的FPGA。不幸的是，LabVIEW的通信方式，有時會導致與 FPGA圖表更新不當，因為他們目前沒有時間同步的時間在芯片上。我組建了一個簡單的應用程序，而不是傳輸分回的主機和波形似乎是正確的。讓我知道這是否有助於。
附件:
Sine.zip ‏317 KB

Conditional error for comparison of sine waves

Hello Everyone,
i am making a small program that is for some changes in sine waves and later i have to compare to set my condition. i cannot get through this error. i actually want out put as bolean so my condition for loop is attached with this output. Anybody please help
Regards
Qasim
Solved!
Go to Solution.
Attachments:
error.png ‏29 KB
test.vi ‏63 KB

Have a look at the examples of the mixed signal graph. That indicator 'eats' nearly everything... wfrms together with XY data with ...
However I didn't get the intensity graph included
Greetings from Germany
Henrik
LV since v3.1
“ground” is a convenient fantasy
'˙˙˙˙uıɐƃɐ lɐıp puɐ °06 ǝuoɥd ɹnoʎ uɹnʇ ǝsɐǝld 'ʎɹɐuıƃɐɯı sı pǝlɐıp ǝʌɐɥ noʎ ɹǝqɯnu ǝɥʇ'
Attachments:
mixedsig.vi ‏12 KB

FFT of Sine Wave-FPGA

Also tried generating a sine wave of 50 Hz and an amplitude of 100 and then do an FFT. But the FFT does not give magnitude at 50 Hz..
Attachments:
FFT-2_Sine Wave Generator.PNG ‏52 KB

Your problem is that the output of the FFT is an array of complex numbers. Take the magnitude and you will be able to plot it.

Sin wave generation for R series FPGA

Similar Messages

Maybe you are looking for