Single Nexus 5548UP- FCoE configuration with multiple server ports

Hello Everyone,
I am new to Networking so please bear with me.
Here is some background information. We have a SINGLE Nexus 5548 UP switch to which we are connecting both the storage and the UCS C240 M3 servers (with CNA). Both the storage and server has 2 ports each going to this nexus switch.
We want to implement FCoE with this solution.
Below are the steps (for server ports) that I have followed to configure the nexus. But the port not logging into the SAN (no flogi) with the config.
Enable Features
config t
feature lacp
feature dot1x
feature interface-vlan
feature sshServer
feature npiv
end
Confgure Ethernet Ports - Server
configure
interface ethernet 1/17
description To_UCS_rack_server_1_FCoE_port_1
switchport mode trunk
switchport trunk native vlan 6
switchport trunk allowed vlan 1,6
spanning-tree port type edge trunk
priority-flow-control mode on
no shutdown
end
configure
interface ethernet 1/18
description To_UCS_rack_server_1_FCoE_port_2
switchport mode trunk
switchport trunk native vlan 6
switchport trunk allowed vlan 1,6
spanning-tree port type edge trunk
priority-flow-control mode on
no shutdown
end
Create VLAN
configure
vlan 6
name FCOE_VLAN
fcoe vsan 6
end
Setup FCoE QOS
configure terminal
system qos
service-policy type qos input fcoe-default-in-policy
service-policy type queuing input fcoe-default-in-policy
service-policy type queuing output fcoe-default-out-policy
service-policy type network-qos fcoe-default-nq-policy
end
Create vfc for Initiators (UCS Servers)
configure
interface vfc 17
bind interface ethernet 1/17
switchport description virtual_fiber_channel_Server1_Port1
end
configure
interface vfc 18
bind interface ethernet 1/18
switchport description virtual_fiber_channel_Server1_Port2
end
Adding vFC’s to VSAN
configure
vsan database
vsan 6 interface vfc 17
vsan 6 interface vfc 18
Create Zonesets and Zones
configure
show flogi database vsan 6 ----> Do not see any pwwn here???
show fcns database vsan 6
Any help in the regard would be highly appreciated.
Cheers,
KS

Fixed the issue. "switchport trunk native vlan 6" was causing the issue. Maybe the storage and Servers were not configured with proper VLAN's. I removed the native vlan and everything logged in fine.
Any how I have configured a single zone with all 3 servers pWWN's. I know single initiator zoning is the way to go.
Can you please guide me if I can move these servers in their separate zones without any outages? If it helps, all severs have 2 pWWN's. The current zoneset is active with that single zone.
Please let me know if you need any additional details.
Cheers,
KS

Similar Messages

CSM - serverfarms configured with multiple probes

Hi - If a serverfarm is configured with multiple probes, do the servers within the farm remain active if they respond positively to both probes or do they just need to respond to one of the configured probes?
Thanks in advance

Both probe must respond positively to make the server appears as OPERATIONAL.
If only one probe is responding positively then the server is considered DOWN
That is usefull for UDP test :
you need to check taht you don't have a RST when openning an UDP connection ( the UDP port is not closed) and you need to make ping (in order to be sure that there is a server ;-) )

How to Restrict Single Delivery Date for PO with Multiple Line Items

Dear Experts,
How to Restrict Single Delivery Date for PO with Multiple Line Items.
System needs to through Error Message if User Inputs Different Delivery Dates for PO with Multiple Line Items in ME21N Tcode.
Can we achive this by Some Enhancement in SAP or Not ???
If so how to do it.
Any Inputs is highly appreciated.
Thanks and Regards,
Selvakumar. M

Hi Selvakumar,
we can resrict the PO to have a single delivery date in all the line items by means of giving a error message or overwiting the delivery date keyed/determined in the line item.
You can use the BADI -> ME_PROCESS_PO_CUST. In which you need to implement the method PROCESS_SCHEDULE.
(for technical aid - This method will be called for each and every PO line item, From the imporing parameter im_schedule we can get all the details of current PO line, even we can change the data in the current PO line. )
Regards,
Madhu.

Need a sample cme with multiple fxo ports, hunt fashion

hi,
anyone kind enough to provide a sample working configuration of multiple fxo ports (each being a pstn line) and I assuming the telco is doing hunting...
so let's say 4 lines, if line 1 is busy the call is sent by the telco on line 2 and so on...
incoming and outgoing.
thank you very much!!
I did google it and can't find anything with multiple fxo ports.

trunk group 1
max-calls voice 4 (or however many POTS lines you want to use)
hunt-scheme round-robin (or whatever method you like)
voice-port 0/0/0
trunk-group 1
connection plar opx XXXX (extension)
caller-id enable
voice-port 0/0/1
trunk-group 1
connection plar opx XXXX
caller-id enable
voice-port 0/0/2
trunk-group 1
connection plar opx XXXX
caller-id enable
voice-port 0/0/3
trunk-group 1
connection plar opx XXXX
caller-id enable
dial-peer voice 1 pots ( I like creating this for troubleshooting, by default cisco router accept incoming calls)
trunkgroup 1
incoming called-number .
direct-inward-dial
dial-peer voice 2 pots
trunkgroup 1
destination-pattern 8[2-9]...... (8 for an outside line or 9 or nothing, then adjust your forward-digits to match)
forward-digits 7
dial-peer voice 3 pots
trunkgroup 1
destination-pattern 81[2-9]..[2-9]......
forward-digits 11
dial-peer voice 4 pots
trunkgroup 1
destination-pattern 8911
forward-digits 3
dial-peer voice 5 pots
trunkgroup 1
destination-pattern 911
forward-digits 3

BSPs configuration with multiple apps servers

Hi Masters,
This is regrarding configure ICM and BSPs on our production box with multiple application servers.
We have our production box in a cluster environment.
The central instance is dbciSAP and apps servers are sapaps2 thru sapaps6. The database is on shared disks. Whenever the central instance fails sapaps2 takes the control and become as dbciSAP but the main dbciSAP never become a application server when ever sapaps2 acts as dbciSAP. Since we have configured load balancing concept in production environment the users can login to system thru any application server. This is waht our environment.
As part of our production box to SAP 4.7 upgrade from 4.6C, we are asked to configure the environment to deploy BSPs. We have successfully configured and deployed the BSPs in our DEV and QAS system (Both are central instances with no application servers) except production box which is due in the next month.
The process we follow to activate BSPs is as follows:
1.Define an ICM service port in /etc/services file.
2.Add the ICM related parameters in instance profiles.
3.Make sure the ICM status is active in SMICM tx.
4.Activate the BSP services in SICF as per OSS note 571484.
Now, the question is how to configure the same ICM service and activate the BSPs since we have multiple multiple application servers.
Subsequently What I am enquirying is:
Do I need to define ICM service ports on each and every hosts where the application servers are running?
Do I need to make changes to each and every instance profile of the application server?
What are the differences in configuring ICM services on central instance and application instances?
Appreciate any help in this regard.
Thanks and Regards
Murty Patchipala

Grasshopper,
I think what you should really read up on is the SAP WebDispatcher. If are serious about running BSP/ICM across multiple app servers, this is the key technology:
http://help.sap.com/saphelp_nw04/helpdata/en/42/5cfd3b0e59774ee10000000a114084/frameset.htm This may also answer some of your questions about profile parameters.
Other than that I can share what we did. We did activate the ICM and services on all app servers and central instance. The service ports of the individual servers aren't that important now because of the WebDispatcher (at least they aren't visible to the user).
Yes we did make some of the ICM profile changes in each instance profile. If your settings are the same, consider using the default profile. Are their particular settings you are interested? I will look over ours, but I don't remember any huge differences from APP server to Central Instance.

3850 switch configure with radius server

wifi useres authenticate with radius server configure required
Posted by WebUser Raja Sekhar from Cisco Support Community App

Kindly check the following links for configuring 802.1x
http://www.cisco.com/en/US/docs/switches/lan/catalyst3850/software/release/3.2_0_se/security/configuration_guide/b_sec_1501_3850_cg_chapter_0101.html
http://www.cisco.com/en/US/docs/switches/lan/catalyst3850/software/release/3.2_0_se/security/configuration_guide/b_sec_1501_3850_cg_chapter_01110.html

EPM 11 Configuration with SQL Server 2005

Hello,
I am having a terrible time trying to get the EPM System Configurer to communicate with SQL Server 2005 Evalution. I keep getting the error "Cannot open database "server" requested by the login. The login failed." I have the windows firewall turned off. The protocol TCPIP is turned on and other protocal are turned off. Any suggestions. Thanks in advance.

As John mentioned it is supposed to be supported in a future release. That version would be 11.2 -- there will be a version coming out before 11.2 and it will not support 2008.
Regards,
John A. Booth
http://www.metavero.com

FPN configured for message server port

Hello,
I would like to configure my Consumer Portal to connect to my Producer on port :8101 (the default message server port of the Producer). However, each time I try with this conifguration FPN breaks and nothing works - can't browse the PCD or see remote roles via Identity Management (when I switch the config back to point to port :50000 in the Producer object on the Consumer it works fine again). I'm not using a SAP web dispatcher between the two portals but Producer portal is indeed listening on port :8101 since I can hit it directly. Is this a limitation of FPN?
My http trace shows an ABORT message when trying to connect with the :8101 configuration.
The 8101 port is necessary to be configured in order to leverage our clustered load balanced environment which has the 8101 message server port listening and redirecting to a cluster of servers.
Patrick

When using Remote Delta Links one can configure the SAP Message Server's RMI-P4 port (3901 by default) for RMI-P4 communication.
For the HTTP load balancing you cannot configure it to point to the HTTP port of SAP Message Server (8101 by default) only the application server's HTTP port on the Central Instance (e.g. 50000) can be used.
But don't bother yourselves with this, because SAP recommends using SAP Webdispatcher for HTTP load balancing in FPN scenario, so don't use SAP Message Server directly for HTTP load balancing in the FPN connection setup!

Modbus IO with multiple ethernet ports?

Dear LabView experts:
My Labview system needs to communicate with three Modbus slave units (motor drive controllers with Modbus TCP/IP option installed) to send commands (speed reference) and read drive status (actual speed, output voltage/current/power etc). The PC has a quad-port Ethernet adapter with three of the ports connected via standard Ethernet cable to the three controllers. The three Ethernet ports on the PC have been given static IP addresses (192.168.1.10, 192.168.1.11, 192.168.1.12). The three controllers have been configured to give the Modbus slave options static IP addresses as well (192.168.1.20, 192.168.1.21, 192.168.1.22). I have also downloaded the NI Modbus library (version 1.2) and would like to use its VIs to perform Modbus Master Query operations. To do this, it is first necessary to open TCP connections to the three slave units using the TCP Open Connection vi, and this is where my problem comes in. How do I bind TCP Open Connection to use a specific Ethernet port (one of the first three IP addresses) on the PC ? Thanks in advance for your help.
VRA
Solved!
Go to Solution.

Hello Mike:
Thanks for your response. I should have browsed this forum a little more before sending the message out. You are right; one way is to restrict each Modbus-dedicated Ethernet port on the PC to a range or even a single port number (using Advanced settings), and use that port number in the TCP Open Connection vi to ensure that this connection will go out of that port. The other way is to use subnet masks as pointed out more than once on this forum; instead of using a subnet mask of 255.255.255.0 for all three ports (which would put them all on the same subnet), I could use a subnet mask of 255.255.255.192 which would allow for four separate subnets, then give the three PC ports IP addresses in the range 192.168.1.(2-62), 192.168.1.(66-126), 192.168.1.(130-190), with gateways set to 192.168.1.1, 192.168.1.65 and 192.168.1.129. The Modbus slave units (motor drive controllers) would then have to be configured with static IP addresses in the respective subnet ranges, so that a TCP Open Connection to that IP address would automatically go out on that subnet.
Thanks again.
VRA

Sql Exception on Testing Configuration with SQL Server JDBC driver for XA

I have a requirement of analyzing the behavior of SQL Server JDBC data sources for XA transactions in our application.We have been using Non-XA drivers for both Oracle and SQL Server as we had no requirement for transactions spanning across multiple databases in past.I have setup and tested the XA driver for Oracle (Oracle Driver (Thin XA) for Instance Connections 9.0.1,9.2.0,10,11) in Weblogic 11g and its working perfectly for transactions spanning across two databases.No when I am trying to configure weblogic 11g R1 for Sql server JDBC driver to support XA transactions with driver details as follows,
Server:Weblogic 11g R1
Driver Type: MS Sql Server
Database Driver :Oracle's MS SQL Server Driver(Type 4 XA) Version:7.0,2000,2005)
Database:SQL Server 2005(Single Instance)
and try to create a new data source and select "Test Configuration" and following error is thrown ,
<Mar 17, 2011 4:49:49 PM GMT+05:30> <Error> <Console> <BEA-240003> <Console encountered the following error java.sql.SQLException: [OWLS][SQLServer JDBC Driver][SQLServer]xa_open (0) returns -3
at weblogic.jdbc.sqlserverbase.BaseExceptions40.createAppropriateSQLExceptionInstance(Unknown Source)
at weblogic.jdbc.sqlserverbase.BaseExceptions40.createSQLException(Unknown Source)
at weblogic.jdbc.sqlserverbase.BaseExceptions.createException(Unknown Source)
at weblogic.jdbc.sqlserverbase.BaseExceptions.getException(Unknown Source)
at weblogic.jdbc.sqlserver.tds.TDSRequest.processErrorToken(Unknown Source)
at weblogic.jdbc.sqlserver.tds.TDSRequest.processReplyToken(Unknown Source)
at weblogic.jdbc.sqlserver.tds.TDSRPCRequest.processReplyToken(Unknown Source)
at weblogic.jdbc.sqlserver.tds.TDSRequest.processReply(Unknown Source)
at weblogic.jdbc.sqlserver.SQLServerImplStatement.getNextResultType(Unknown Source)
at weblogic.jdbc.sqlserverbase.BaseStatement.commonTransitionToState(Unknown Source)
at weblogic.jdbc.sqlserverbase.BaseStatement.postImplExecute(Unknown Source)
at weblogic.jdbc.sqlserverbase.BasePreparedStatement.postImplExecute(Unknown Source)
at weblogic.jdbc.sqlserverbase.BaseStatement.commonExecute(Unknown Source)
at weblogic.jdbc.sqlserverbase.BaseStatement.executeUpdateInternal(Unknown Source)
at weblogic.jdbc.sqlserverbase.BasePreparedStatement.executeUpdate(Unknown Source)
at weblogic.jdbcx.sqlserver.SQLServerImplXAResource.executeXaRpc(Unknown Source)
at weblogic.jdbcx.sqlserver.SQLServerImplXAResource.executeXaRpc(Unknown Source)
at weblogic.jdbcx.sqlserver.SQLServerImplXAResource.open(Unknown Source)
at weblogic.jdbcx.sqlserverbase.BaseXAConnection.init(Unknown Source)
at weblogic.jdbcx.sqlserverbase.BaseXAConnection40.init(Unknown Source)
at weblogic.jdbc.sqlserverbase.BaseClassCreatorForJDBC40.createXaConnection(Unknown Source)
at weblogic.jdbcx.sqlserverbase.BaseXADataSource.getXAConnection(Unknown Source)
at com.bea.console.utils.jdbc.JDBCUtils.testConnection(JDBCUtils.java:550)
at com.bea.console.actions.jdbc.datasources.createjdbcdatasource.CreateJDBCDataSource.testConnectionConfiguration(CreateJDBCDataSource.java:450)
at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method)
at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.java:39)
at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:25)
at java.lang.reflect.Method.invoke(Method.java:597)
at org.apache.beehive.netui.pageflow.FlowController.invokeActionMethod(FlowController.java:870)
at org.apache.beehive.netui.pageflow.FlowController.getActionMethodForward(FlowController.java:809)
at org.apache.beehive.netui.pageflow.FlowController.internalExecute(FlowController.java:478)
at org.apache.beehive.netui.pageflow.PageFlowController.internalExecute(PageFlowController.java:306)
at org.apache.beehive.netui.pageflow.FlowController.execute(FlowController.java:336)
at org.apache.beehive.netui.pageflow.internal.FlowControllerAction.execute(FlowControllerAction.java:52)
at org.apache.struts.action.RequestProcessor.processActionPerform(RequestProcessor.java:431)
at org.apache.beehive.netui.pageflow.PageFlowRequestProcessor.access$201(PageFlowRequestProcessor.java:97)
at org.apache.beehive.netui.pageflow.PageFlowRequestProcessor$ActionRunner.execute(PageFlowRequestProcessor.java:2044)
at org.apache.beehive.netui.pageflow.interceptor.action.internal.ActionInterceptors$WrapActionInterceptorChain.continueChain(ActionInterceptors.java:64)
at org.apache.beehive.netui.pageflow.interceptor.action.ActionInterceptor.wrapAction(ActionInterceptor.java:184)
at org.apache.beehive.netui.pageflow.interceptor.action.internal.ActionInterceptors$WrapActionInterceptorChain.invoke(ActionInterceptors.java:50)
at org.apache.beehive.netui.pageflow.interceptor.action.internal.ActionInterceptors$WrapActionInterceptorChain.continueChain(ActionInterceptors.java:58)
at org.apache.beehive.netui.pageflow.interceptor.action.internal.ActionInterceptors.wrapAction(ActionInterceptors.java:87)
at org.apache.beehive.netui.pageflow.PageFlowRequestProcessor.processActionPerform(PageFlowRequestProcessor.java:2116)
at com.bea.console.internal.ConsolePageFlowRequestProcessor.processActionPerform(ConsolePageFlowRequestProcessor.java:261)
at org.apache.struts.action.RequestProcessor.process(RequestProcessor.java:236)
at org.apache.beehive.netui.pageflow.PageFlowRequestProcessor.processInternal(PageFlowRequestProcessor.java:556)
at org.apache.beehive.netui.pageflow.PageFlowRequestProcessor.process(PageFlowRequestProcessor.java:853)
at org.apache.beehive.netui.pageflow.AutoRegisterActionServlet.process(AutoRegisterActionServlet.java:631)
at org.apache.beehive.netui.pageflow.PageFlowActionServlet.process(PageFlowActionServlet.java:158)
at com.bea.console.internal.ConsoleActionServlet.process(ConsoleActionServlet.java:256)
at org.apache.struts.action.ActionServlet.doGet(ActionServlet.java:414)
at com.bea.console.internal.ConsoleActionServlet.doGet(ConsoleActionServlet.java:133)
at org.apache.beehive.netui.pageflow.PageFlowUtils.strutsLookup(PageFlowUtils.java:1199)
at com.bea.portlet.adapter.scopedcontent.ScopedContentCommonSupport.executeAction(ScopedContentCommonSupport.java:686)
at com.bea.portlet.adapter.scopedcontent.ScopedContentCommonSupport.processActionInternal(ScopedContentCommonSupport.java:142)
at com.bea.portlet.adapter.scopedcontent.PageFlowStubImpl.processAction(PageFlowStubImpl.java:106)
at com.bea.portlet.adapter.NetuiActionHandler.raiseScopedAction(NetuiActionHandler.java:111)
at com.bea.netuix.servlets.controls.content.NetuiContent.raiseScopedAction(NetuiContent.java:181)
at com.bea.netuix.servlets.controls.content.NetuiContent.raiseScopedAction(NetuiContent.java:167)
at com.bea.netuix.servlets.controls.content.NetuiContent.handlePostbackData(NetuiContent.java:225)
at com.bea.netuix.nf.ControlLifecycle$2.visit(ControlLifecycle.java:180)
at com.bea.netuix.nf.ControlTreeWalker.walkRecursive(ControlTreeWalker.java:324)
at com.bea.netuix.nf.ControlTreeWalker.walkRecursive(ControlTreeWalker.java:334)
at com.bea.netuix.nf.ControlTreeWalker.walkRecursive(ControlTreeWalker.java:334)
at com.bea.netuix.nf.ControlTreeWalker.walkRecursive(ControlTreeWalker.java:334)
at com.bea.netuix.nf.ControlTreeWalker.walkRecursive(ControlTreeWalker.java:334)
at com.bea.netuix.nf.ControlTreeWalker.walkRecursive(ControlTreeWalker.java:334)
at com.bea.netuix.nf.ControlTreeWalker.walkRecursive(ControlTreeWalker.java:334)
at com.bea.netuix.nf.ControlTreeWalker.walkRecursive(ControlTreeWalker.java:334)
at com.bea.netuix.nf.ControlTreeWalker.walkRecursive(ControlTreeWalker.java:334)
at com.bea.netuix.nf.ControlTreeWalker.walkRecursive(ControlTreeWalker.java:334)
at com.bea.netuix.nf.ControlTreeWalker.walkRecursive(ControlTreeWalker.java:334)
at com.bea.netuix.nf.ControlTreeWalker.walkRecursive(ControlTreeWalker.java:334)
at com.bea.netuix.nf.ControlTreeWalker.walkRecursive(ControlTreeWalker.java:334)
at com.bea.netuix.nf.ControlTreeWalker.walkRecursive(ControlTreeWalker.java:334)
at com.bea.netuix.nf.ControlTreeWalker.walkRecursive(ControlTreeWalker.java:334)
at com.bea.netuix.nf.ControlTreeWalker.walkRecursive(ControlTreeWalker.java:334)
at com.bea.netuix.nf.ControlTreeWalker.walkRecursive(ControlTreeWalker.java:334)
at com.bea.netuix.nf.ControlTreeWalker.walkRecursive(ControlTreeWalker.java:334)
at com.bea.netuix.nf.ControlTreeWalker.walkRecursive(ControlTreeWalker.java:334)
at com.bea.netuix.nf.ControlTreeWalker.walkRecursive(ControlTreeWalker.java:334)
at com.bea.netuix.nf.ControlTreeWalker.walkRecursive(ControlTreeWalker.java:334)
at com.bea.netuix.nf.ControlTreeWalker.walkRecursive(ControlTreeWalker.java:334)
at com.bea.netuix.nf.ControlTreeWalker.walkRecursive(ControlTreeWalker.java:334)
at com.bea.netuix.nf.ControlTreeWalker.walk(ControlTreeWalker.java:130)
at com.bea.netuix.nf.Lifecycle.processLifecycles(Lifecycle.java:395)
at com.bea.netuix.nf.Lifecycle.processLifecycles(Lifecycle.java:361)
at com.bea.netuix.nf.Lifecycle.processLifecycles(Lifecycle.java:352)
at com.bea.netuix.nf.Lifecycle.runInbound(Lifecycle.java:184)
at com.bea.netuix.nf.Lifecycle.run(Lifecycle.java:159)
at com.bea.netuix.servlets.manager.UIServlet.runLifecycle(UIServlet.java:388)
at com.bea.netuix.servlets.manager.UIServlet.doPost(UIServlet.java:258)
at com.bea.netuix.servlets.manager.UIServlet.service(UIServlet.java:199)
at com.bea.netuix.servlets.manager.SingleFileServlet.service(SingleFileServlet.java:251)
at javax.servlet.http.HttpServlet.service(HttpServlet.java:820)
at com.bea.console.utils.MBeanUtilsInitSingleFileServlet.service(MBeanUtilsInitSingleFileServlet.java:47)
at weblogic.servlet.AsyncInitServlet.service(AsyncInitServlet.java:130)
at weblogic.servlet.internal.StubSecurityHelper$ServletServiceAction.run(StubSecurityHelper.java:227)
at weblogic.servlet.internal.StubSecurityHelper.invokeServlet(StubSecurityHelper.java:125)
at weblogic.servlet.internal.ServletStubImpl.execute(ServletStubImpl.java:292)
at weblogic.servlet.internal.TailFilter.doFilter(TailFilter.java:26)
at weblogic.servlet.internal.FilterChainImpl.doFilter(FilterChainImpl.java:56)
at weblogic.servlet.internal.RequestEventsFilter.doFilter(RequestEventsFilter.java:27)
at weblogic.servlet.internal.FilterChainImpl.doFilter(FilterChainImpl.java:56)
at weblogic.servlet.internal.WebAppServletContext$ServletInvocationAction.run(WebAppServletContext.java:3592)
at weblogic.security.acl.internal.AuthenticatedSubject.doAs(AuthenticatedSubject.java:321)
at weblogic.security.service.SecurityManager.runAs(SecurityManager.java:121)
at weblogic.servlet.internal.WebAppServletContext.securedExecute(WebAppServletContext.java:2202)
at weblogic.servlet.internal.WebAppServletContext.execute(WebAppServletContext.java:2108)
at weblogic.servlet.internal.ServletRequestImpl.run(ServletRequestImpl.java:1432)
at weblogic.work.ExecuteThread.execute(ExecuteThread.java:201)
at weblogic.work.ExecuteThread.run(ExecuteThread.java:173)
I followed the instruction in weblogic jdbc drivers guide to configure the JTA Transactions to support XA on SQL Server machine and weblogic server which included,
1.Copying sqljdbc.dll copied to SQL_Server_Root/bin directory from WL_HOME\server\lib.
2.Copied instjdbc.sql to sql server machine and executed the script with following output,
Changed database context to 'master'.
Msg 3701, Level 11, State 5, Server SQLDB, Procedure sp_dropextendedproc, Line 16
Cannot drop the procedure 'xp_jdbc_open', because it does not exist or you do not have permission.
Msg 3701, Level 11, State 5, Server SQLDB, Procedure sp_dropextendedproc, Line 16
Cannot drop the procedure 'xp_jdbc_open2', because it does not exist or you do not have permission.
Msg 3701, Level 11, State 5, Server SQLDB, Procedure sp_dropextendedproc, Line 16
Cannot drop the procedure 'xp_jdbc_close', because it does not exist or you do not have permission.
Msg 3701, Level 11, State 5, Server SQLDB, Procedure sp_dropextendedproc, Line 16
Cannot drop the procedure 'xp_jdbc_close2', because it does not exist or you do not have permission.
Msg 3701, Level 11, State 5, Server SQLDB, Procedure sp_dropextendedproc, Line 16
Cannot drop the procedure 'xp_jdbc_start', because it does not exist or you do not have permission.
Msg 3701, Level 11, State 5, Server SQLDB, Procedure sp_dropextendedproc, Line 16
Cannot drop the procedure 'xp_jdbc_start2', because it does not exist or you do not have permission.
Msg 3701, Level 11, State 5, Server SQLDB, Procedure sp_dropextendedproc, Line 16
Cannot drop the procedure 'xp_jdbc_end', because it does not exist or you do not have permission.
Msg 3701, Level 11, State 5, Server SQLDB, Procedure sp_dropextendedproc, Line 16
Cannot drop the procedure 'xp_jdbc_end2', because it does not exist or you do not have permission.
Msg 3701, Level 11, State 5, Server SQLDB, Procedure sp_dropextendedproc, Line 16
Cannot drop the procedure 'xp_jdbc_prepare', because it does not exist or you do not have permission.
Msg 3701, Level 11, State 5, Server SQLDB, Procedure sp_dropextendedproc, Line 16
Cannot drop the procedure 'xp_jdbc_prepare2', because it does not exist or you do not have permission.
Msg 3701, Level 11, State 5, Server SQLDB, Procedure sp_dropextendedproc, Line 16
Cannot drop the procedure 'xp_jdbc_commit', because it does not exist or you do not have permission.
Msg 3701, Level 11, State 5, Server SQLDB, Procedure sp_dropextendedproc, Line 16
Cannot drop the procedure 'xp_jdbc_commit2', because it does not exist or you do not have permission.
Msg 3701, Level 11, State 5, Server SQLDB, Procedure sp_dropextendedproc, Line 16
Cannot drop the procedure 'xp_jdbc_rollback', because it does not exist or you do not have permission.
Msg 3701, Level 11, State 5, Server SQLDB, Procedure sp_dropextendedproc, Line 16
Cannot drop the procedure 'xp_jdbc_rollback2', because it does not exist or you do not have permission.
Msg 3701, Level 11, State 5, Server SQLDB, Procedure sp_dropextendedproc, Line 16
Cannot drop the procedure 'xp_jdbc_forget', because it does not exist or you do not have permission.
Msg 3701, Level 11, State 5, Server SQLDB, Procedure sp_dropextendedproc, Line 16
Cannot drop the procedure 'xp_jdbc_forget2', because it does not exist or you do not have permission.
Msg 3701, Level 11, State 5, Server SQLDB, Procedure sp_dropextendedproc, Line 16
Cannot drop the procedure 'xp_jdbc_recover', because it does not exist or you do not have permission.
Msg 3701, Level 11, State 5, Server SQLDB, Procedure sp_dropextendedproc, Line 16
Cannot drop the procedure 'xp_jdbc_recover2', because it does not exist or you do not have permission.
creating JDBC XA procedures
instxa.sql completed successfully.
3.Verified that MSDTC service is running on both SQL Server and weblogic machines with XA Transaction enabled and DTC option enabled for both inbound and outbound connections.
4.Copied sqljdbc.jar (version 3.0 downloaded from msdn portal) to "C:\Oracle\Middleware\wlserver_10.3\server\ext\jdbc\sqlserver" directory and updated weblogic_classpth variable in commEnv.cmd file.
set WEBLOGIC_CLASSPATH=%JAVA_HOME%\lib\tools.jar;%BEA_HOME%\utils\config\10.3\config-launch.jar;%WL_HOME%\server\lib\weblogic_sp.jar;%WL_HOME%\server\lib\weblogic.jar;%FEATURES_DIR%\weblogic.server.modules_10.3.2.0.jar;%WL_HOME%\server\lib\webservices.jar;%ANT_HOME%/lib/ant-all.jar;%ANT_CONTRIB%/lib/ant-contrib.jar;C:\Oracle\Middleware\wlserver_10.3\server\ext\jdbc\sqlserver\server\ext\jdbc\sqlserver\sqljdbc.jar
Can some one please provide some input on whats causing this and any other steps needs to be followed to implement XA support using SQL Server JDBC driver.

You seem to have done everything correctly and diligently. I would ask that you open
an official support case.

Nexus 5548UP FCoE

Hi,
I'm trying to setup an connection from Netapp to n5k using CNA card on Netapp.
I've configured n5k as it should, but it seems that it always fails with:
2011 Jun 27 11:45:19 site1-n5k-sw1 %PORT-5-IF_TRUNK_DOWN: %$VSAN 50%$ Interface vfc31, vsan 50 is down (waiting for flogi)
Any ideas if it's configured wrongly on nexus side ... (?) Thanks.
feature fcoe
interface Ethernet1/23
switchport mode trunk
spanning-tree port type edge trunk
vlan 50
fcoe vsan 50
vsan database
vsan 50 interface vfc31
interface vfc31
bind interface Ethernet1/23
switchport trunk allowed vsan 50
no shutdown
# sh vsan membership
vsan 50 interfaces:
    fc1/29            vfc31
n5k-sw1(config-if)# sh int vfc31
vfc31 is trunking
    Bound interface is Ethernet1/23
    Hardware is Virtual Fibre Channel
    Port WWN is 20:1e:00:05:73:f2:b0:bf
    Admin port mode is F, trunk mode is on
    snmp link state traps are enabled
    Port mode is TF
    Port vsan is 50
    Trunk vsans (admin allowed and active) (50)
    Trunk vsans (up)                       ()
    Trunk vsans (isolated)                 ()
    Trunk vsans (initializing)             (50)
    1 minute input rate 0 bits/sec, 0 bytes/sec, 0 frames/sec
    1 minute output rate 0 bits/sec, 0 bytes/sec, 0 frames/sec
      0 frames input, 0 bytes
        0 discards, 0 errors
      0 frames output, 0 bytes
        0 discards, 0 errors
    last clearing of "show interface" counters never
    Interface last changed at Mon Jun 27 11:43:17 2011
-n5k-sw1(config-if)# sh flogi database
INTERFACE        VSAN    FCID           PORT NAME               NODE NAME
fc1/29           50    0xb80000 20:41:00:05:73:e3:59:80 20:32:00:05:73:e3:59:81
Total number of flogi = 1.

Documentation says so
The Ethernet interface that you bind the virtual Fibre Channel interface to must be configured as follows:
•It must be a trunk port (use the switchport mode trunk command).
•The FCoE VLAN that corresponds to virtual Fibre Channel's VSAN must be in the allowed VLAN list.

How configure reporting services configuration with sql server business development studio

I have installed sql server 2008 r2 mixed mode(sql server authentication) with native mode
I want to run report using reporting services config manager.
I made report in ssrs and I have configured reporting services configuration and web url from RSCM( reporting services config manager), i put on ssrs report.
report is build and deployed but when i take deployed url on Internet explorer, it shows the window below:
when I put the password nothing happened . if I put url in google chrome then it shows authentication required window like the same in IE
if I passed username=(levent/sa) and password then goes on window but does not see on page, if I passed only administrator name (levent) not passed sql server login name (sa) then does not close 'Authentication window'
'Computer connect net with modem'
before i tried on earlier PC, it worked fine.
setting is below link like this.
only set service Account is Use_built=NetworkSrvice
link
http://www.azurecurve.co.uk/2012/02/how-to-configure-sql-server-reporting-services-in-order-to-deploy-reporting-services-reports-in-gp/
what is the problem
Plz give suggestion quickly

Hi tusharshinde,
Per my understanding that when you log in the report Manager you got the pop-up window ask for credential, you try to enter the SA account and the window account as the username and password but both not work, right?
Your issue related to the authentication. As you mentioned you have choose the ”Network Service” as the Service account, generally using this account in RSCM and RSWindowsNegotiate is added to the RSReportServer.config file as the default setting. With this
setting, the report server can accept requests from client applications requesting Kerberos or NTLM authentication. If Kerberos is requested and the authentication fails, the report server switches to NTLM authentication and prompts the user for credentials
unless the network is configured to manage authentication transparently.
The issue can be caused by many factors and please check one by one.
Did you enter the username and password for three times and got blank page or got some error? If you got some error, please provide the error information.
you can delete the specific Authorization Types inside rsreportserver.config file, open path:” \Program Files\Microsoft SQL Server\MSRS10_50.MSSQLSERVER\Reporting Services\ReportServer\rsreportserver.config”.
Search the file for the “AuthenticationTypes” section. Remove RSWindowsNegotiate and RSWindoeBasic to ensure only “RSWindowsNTLM” is specified in the file rsreportserver.config file.
Before do any modification, back up the files and remember to restart the ReportServer instance in the RSCM after the modification.
If step1 doesn’t work ,please also do the trusted Site Setting in the Browser, article with details steps for your reference:
http://technet.microsoft.com/en-us/library/bb630430.aspx
Please check the Report Manager's authentication mode.Have a look in the Report Manager's web.config file to check if you can find below information under the <system.web> (Path is “C:\Program Files\Microsoft SQL Server\MSRS10_50.MSSQLSERVER\Reporting
Services\ReportManager\Web.config ” ).
authentication mode="Windows"
identity impersonate="True"
Similar threads for your reference:
https://social.msdn.microsoft.com/Forums/sqlserver/en-US/23c5daa0-3232-4e8c-89c9-4526960c9d14/ssrs-2008-credentials-login-prompt?forum=sqlreportingservices
https://social.msdn.microsoft.com/Forums/sqlserver/en-US/0778e2ca-0fb1-4b5c-996c-6e327b5e1473/user-logon-credentials-for-ssrs-web-server-setup?forum=sqlreportingservices
Please tried to provide us more details information, if the problem still exists:
Did you login in the report manager locally or remotely via Browser and which URL you are using to login the Report manager?
Did you modified some configuration file before and what did you modified?
Did your windows account have the right permission to access the report manager?
Any problem, please feel free to ask.
Regards
Vicky Liu

Airport Extreme configuration with Linux server gateway.

Hello all-
I am sorry if this is a repeat post.... I looked and could not find anything. I am trying to set up a linux server and have it act as a gateway between my Airport Extreme and my modem. I am wondering if there is a way to set a static IP on the airport extreme, or do I assign the address on the NIC in the linux box. The internal network will have OS X, Windows and Linux on it.
Also is there a flavor of linux that works better than others with Apple equipment?
Thank you for your patience and help!
Cheers!

I am wondering if there is a way to set a static IP on the airport extreme
Yes, there is. You would do so using the AirPort Utility. (ref: AirPort Utility > Manual Setup > Internet > Internet Connection > Configure IPv4 = Manually) You can then enter the desired IP address information as required for your network configuration.

BI Publisher configured with BI Server Security not working for the admins.

Hello Everyone,
I have configured the BI publisher to work with the BI server security. Everything is working well with the exception that all users part of the BI Server "Administrators" group are unable to login and get the following error message (message displayed below). If a user is removed from the "Administrators" group then they are able to access the BI Publisher. As indicated everything else is working for exemple all users part of the 'XMLP_Admin' group all have access to the "ADMIN" tab in BI Publisher. The issue seems to be limited to the users part of the BI Server "Administrators" group.
- Has anyone else ever had this issue?
- Is this a normal behaviour of BI Publisher?
- Or the security groups for the BI Server and BI Publisher conflicting?
Thanks in advance for everyone's help.
Best regards,
FBELL
*********************** Error Message ***************************************
Oracle BI Publisher Enterprise
Reporting Login: Login failed: Please contact administrator for your username/password.
Error Details
Error Codes:
***************************************************************************

Thanks Madan for your help.
The group XMLP_Admin was already created and working. The conflict was with security groups outside BI Publisher. What I ended up doing was recreating the principals.xml and security.xml files and rsetting the roles and permissions. Surprisingly that fixed my problem.
Best regards,
FBELL.

Nexus 5548UP FCoE to C series UCS

Ok here is the scenario
nexus 5548 switch ---- fex 2232 --- UCS C series (C220)
snippets of the configuration:
vlan 1100
fcoe vsan 1100
vlan database
vsan 1100
fex 100
description 2232-A
fcoe
int ethernet100/1/1
switchport
switchport mode trunk
switchport trunk allowed vlan 10,1100
interface vfc100
bind interface ethernet100/1/1
switchport trunk allowed vsan 1100
no shut
so it is configured above, the vfc interface won't trunk unless I do the following:
vsan database
vsan 1100 interface vfc100
I found this document that describes mapping VSANs to VLANs example configuration (page 8)

Each fc and/or vfc interface must be member of a VSAN; by default, they belong all initially to VSAN 1.

Single Nexus 5548UP- FCoE configuration with multiple server ports

Similar Messages

Maybe you are looking for