Sisoftware Sandra: Is there a reason to stay away from this software?

I have not noticed Sisoftware Sandra recommended by folks on this website.
Is there a reason I should stay away from Sandra?

I suppose, there is no real reason to stay away from it. The point is, I believe, that it is in general not as popular as (let's say) tool like Everest/Aida, HW Monitor, CPU-Z, GPU-Z, Core Temp, Real Temp and the like.

Similar Messages

EA6500 worst experience - stay away from this router

Hi Everyone,
EA64500 is worst, stay away from this router, since last 2 days I spend more than 4 hours with Linksys support and it is useless ans wastage of time.
I am going to return this junk to Costco. It works for 2 months only after spending hundreds of dollars. It sounds rosy but the product is crep.
Check out real problem at following link
http://www.gottabemobile.com/2013/05/12/linksys-ea6500-wireless-router-a-beast-to-set-up-but-then-wo...

There are many reasons why a connection could be intermittent. It might be because the connection to the ISP is unstable, to much wireless traffic, frequency interference from other wireless devices, physical obstructions or corrupted router firmware.
The location where your wireless router and computer are placed affects the performance of your wireless network. To boost the wireless signal, it is ideal to place the wireless router either in the central part of your house or in a location free from any obstructions that may block its range. The frequency used by your router’s wireless network can be set to 2.4 GHz, 5 GHz, or Mixed. Interference happens if there is conflict with some wireless devices that are also using the same frequency within your network. The most common examples of devices that use the same frequency are cordless phones, microwave ovens, and baby monitors. Another factor that could cause interference would be a separate wireless network which operates in the same frequency as your routers.
If all computers connected to the router are experiencing intermittent connections, it would be best to observe the connection straight from the modem. Observe it for 24 hours and if there are no issues then best to upgrade the router’s firmware.

How do I stop "Are you sure you want to navigate away from this page? Press OK to continue, or Cancel to stay on the current page." from comeing up. It is new. Just started doing it yesterday morning.

I have used FireFox to play the Game Kingdoms Of Camelot, a facebook game. I also have Grease Monkey and a 3rd party add on. I leave it running 24/7 to gather food in the game for my army. It has run smoothly for 6 mo. Yesterday 2/04/11 in the morning it started asking for conformation when the page refreshed. i want to know how to stop this Box from comeing up it will not continue without refreshing and will not refresh untill th question is answered. It says "Are you sure you want to navigate away from this page? Press OK to continue, or Cancel to stay on the current page."

You're not going to stop it, and out here, what's illegal?
What it boils down to is a matter of ethics, and it's wrong. But the web
techies build this feature into their sites because they know somebody
is going to fly in off an engine like Google or MSN. And take something,
like a picture. Without stopping in and signing up or something else.
But what if I or you is out collecting stamps or avatars or wallpapers,
and have already taken a quiz, or signed up for a product? I've already
done that...but the site developers who use this ingenious(hijacking)
software don't see it that way, and don't care if you just got a computer
and want to pick up something here or there. Those sites don't get
anything when you visit and don't leave your number. I don't what
these 19 tracking cookies are for, do you?
"A liar should have a good memory" Scottish saying

Are you a Veteran? Stay away from Verizon!

If you are veteran hoping to get a 15% discount from Verizon then stay the heck away. You won't get it. Go with AT&T who will give it to you. I'm regretting switching over.
Went into official Verizon store with DD214 in hand. Verizon agent scanned document, assured me I would get the 15% discount on my plan immediately. I actually asked two more times just to be sure. She assured me each time. Verizon site says I am verified.
First bill came, no discount. I called Verizon and they said it can take 30 days. Upset me a bit but I waited.
Second bill came, no discount. Chatted with a Verizon representative who said my plan is not eligible. I checked my plan details. Nothing written there about it being in-eligible. Checked the Veteran Discount FAQ and it specifically states: Note: some plans and features are not eligible for discounts and that limitation will be called out in the plan details. However, my plan details say nothing of the sort. The agent could not give me the discount and just kept repeating that my plan was not eligible for the discount.
So even though I was promised the discount from a Verizon Wireless Agent at an official store and my plan does not say anything about me being in-eligible, Verizon has refused to give me the discount due to very arbitrary wording. They even have a link that is suppose to show you in-eligible plans but it does not work. The representative told me that they change the eligible plans all the time. So even if I got the discount they would probably just change the eligibility in the future.
I was about to recommend a few other veterans to move over to Verizon but now I am telling them to go somewhere else. I should inform the local Department of Veteran Affairs here so they can properly inform any veteran that might call in and ask.
Verizon should be pretty ashamed of themselves.
My Plan: Single Line $60 - 2GB

I Totally AGREE...STAY AWAY FROM VERIZON!! Work for Fed Govt, DoD....according to Verizon's rules, Qualified for the Employee Discount....NOT.....Previously worked for Kroger...applied for the employee discount as a Kroger Employee and the discount never showed up on the billing....Customer service WAS NO HELP....signed up with a Verizon Rep at one of their stores.....Go Figure...Now signed up for employee discount (GOVT) over the net. Said was eligible...After signed up called to verify the discount..Rep said , Oh, you're not qualified?????? I hope that you get your issue resolved. You would think that being you are ACTIVE DUTY...and....service our wonderful COUNTRY (US) that Verizon would even be more helpful and courteous to you, as an Active Duty Service person!!! GOOD LUCK TO YOU...AS FOR ME....As soon as my contract is up, AUG 14, 2011 ( I Can't WAIT)...I'm changing over to SPRINT....Several co-workers use SPRINT...love the service and told me that there are NO HASSELS about giving the US GOVT EMPLOYEE DISCOUNT....{please keep your posts courteous}....SPRINT ROCKS!!
Signed...Disgruntled customer

HOW DO I GET RID OF THIS MESSAGE, PLEASE???Are you sure you want to navigate away from this page? Press OK to continue, or Cancel to stay on the current page.

everytime I go to leave a page or click on something this, this message appears and I cant find where to disable it. It just started today. Never did it before.
Are you sure you want to navigate away from this page?
Press OK to continue, or Cancel to stay on the current page

Do you have that problem when running in the Firefox SafeMode? 
[http://support.mozilla.com/en-US/kb/Safe+Mode] 
''Don't select anything right now, just use "Continue in SafeMode."''
If not, see this: 
[http://support.mozilla.com/en-US/kb/troubleshooting+extensions+and+themes]

I have a Sony DCR -SR32 which does not appear in the list of compatible cameras for imovie '11. Does anyone know if there is way to import files from this camera ?

I have a Sony DCR-SR32 HDD video camera which does not appear in the list of compatible cameras for imovie '11. Does anyone know if there is way of importing video from this camera to imovie ?
Thanks
Pheona

Greetings Pheona,
That appears to be a hard drive based camecorder. Usually these mount on the desktop of your computer as a little white hard drive icon. If you go inside you should be able to find the movie files the camera is saving. See what format they are (the last 3 letters at the end of the file name is a good place to start).
You can drag the movie files from the camera hard drive to the computer to copy them. Then convert them with a video file conversion program to a format iMovie can understand.
Try converting one of the files using a video file conversion program like Video Monkey: http://videomonkey.org/downloads/
In the "Convert to" drop down menu choose "DV" (Preferred), "Quicktime", or "MP4". Then import the resulting file into iMovie and see if that works any better.
If that program can't convert the files you can try another file conversion program:
http://www.southpolesoftware.com/iVI/iVI.php
http://shedworx.com/voltaichd
http://www.elgato.com/elgato/na/mainmenu/products/Turbo264HD-software/product1.e n.html
Hope that helps.

Is there any reason I shouldn't work this way?

Given the lack of batch capture in FCE is there any reason why I shouldn't work in the following way:
1. Import video in large chunks using capture now
2. Use DV start stop and Make sub-clip
3. Export just the sub-clips I want as self-contained movies
4. Close the project and delete the original capture files and the FCE project file
5. Start a new project and import the movies I saved in step 3.
My reasons for wanting to do this are mainly to save disc space but also to reduce clutter in the bins. So far as I can see this works fine. The only downsides I can see are:
1. The extra time it takes but this is offset against the chore of capturing individual clips instead of using capture now.
2. The fact that reimported clips have their audio tracks set to mono mix but it seems easy enough to correct this. (As an aside, if I import a .mov file saved from Quicktime it imports into FCE with the audio set to stereo - why the difference?).
I'd be happy enough working this way, I think, provided I could be confident that I'm not going to lose quality by saving and then re-importing. Will I? Are there any other downsides I've not thought of?

You shouldn't lose any quality in the audio or video, but you may lose the timecode track. I'm not sure if you'll lose it, but if you do, you won't be able to recapture the project clips from the original tape because the timecode would be required. This isn't an issue, if you don't ever need to recapture. The timecode may even be retained... I'd have to do an export to see. As a matter of workflow, you may want to think seriously about keeping the timecode, because you can back-up your project file and have some assurance that you can recover from a chatastrophic failure simply by restoring the project file and recapturing from the original tape.
Regarding your audio and video; unless you were to add effects to the video, there should be no loss in exporting and importing. Losses in DV are incurred when you add filters (alter the image) and recompress. The audio is uncompressed PCM, so no losses to be had there, unless you change the sampling rate.

Trackpad Erratic Insanity; Stay away from Fluorescent Tubes, EMI!

Yesterday I was helping a friend with her new 13" Aluminum MacBook. She sat the MacBook down on one of the glass display cases in her gift store. We fired up the computer only to find that the trackpad had gone totally nuts. I could get the pointer to move only a tiny amount. Clicking caused very strange behavoiur such as bringing up the "right click" menu, and activating Expose'. Luckily, we had a Kensington mouse handy; the mouse worked just fine. Because our friend had just installed some new software, I repaired Permissions and scanned the hard drive via Disk Utilities & rebooted. Trackpad still useless, I moved the laptop to a counter near the phone so I could call Apple Tech Support. While I was dialing in and on hold, I noticed that the trackpad seemed to be working normally. After scratching my head in disbelief, I noticed that there was a 4' Fluorescent lamp in a bezel at the upper front of the glass display case to illuminate the case's contents. Relocating the MacBook to its original position on the glass case duplicated the original Trackpad disfunction. I informed the Tech Support person of the incident so she could add it to Apple's troubleshooting database, and also suggested that she needed to inform Apple's Engineering/QA departments so they could do further testing, etc. Luckily no apparent damage was done to the computer, but it easily could have. Moral of the story: KEEP YOUR MACBOOK AWAY FROM SOURCES OF STRONG ELECTROMAGNETIC INTERFERENCE, such as fluorescent or neon lamps, motors, etc. Even though I have figured out this problem, I thought it would be very helpful to make this post.
Best to you all!

I have had an iPod Touch 3rd Gen for two years and the apps have worked fine in the past. Suddenly the apps will not launch, they appear to start then just exit. Is there a reason why it is doing this?

I have had an iPod Touch 3rd Gen for two years pretty much and the apps have worked fine. Suddenly when I go on an app it appears to launch then just exits. I tried turning the iPod off and on again, but that made all my apps behave like that. Settings and those things work fine still. Should this suddenly happen? I dont want to lose all 204 apps.

- First try resetting the iPod. Nothing will be lost.
Reset iPod touch: Press and hold the On/Off Sleep/Wake button and the Home
button at the same time for at least ten seconds, until the Apple logo appears.
- Next try downloading/installing a new app
- Restore from backup
- Last, resore to factory defaults/new iPod. this is last result since you will lose app data.

TS1741 Is there a way to get sound from this app?

It shows time elapsed on what I'm watching so there is a connection. The roku 3 has a headphone plug in the remote, step it up apple.

Yes I am, I'm not satisfied with an application apple makes or perhaps I'm not using it right. The support for iTunes is not streamlined like android so I've been going in circles to figure how to talk about my confusion with this feature.

Horrible, stay away from fios.

My bill was accidentally changed through my remote. Customer service told me they could get my plan back but it would be more expensive because they no longer offer it. I had it yesterday. When I mentioned it was an accident all they did was suggest putting a lock, well great but that doesn't help me. Now my bill has increased for the same services and will increase again in 1 year and I'm stuck for 2 years. HORRIBLE CUSTOMER SERVICE. No help, basically made it my fault and now I'm stuck. After these 2 years I'm switching back to Comcast, Ive had Fios for 4 months and have had nothing but trouble. My suggestion, don't be inticed by the pricing, it'll come back to bite you.

I agree. I called Fios 3 times to lower my TV bill with no success. I moved to DirectTV and called to cancel then Verizon offered me a discount to stay.
I asked for a discount for my Internet and Phone. The Customer Service rep was rude and tried to lock me into a 2 year contract with no discount or promotional price. Dont let them bully you into a contract. I am staying for now, month to month, until I can get my wife's email migrated. I can get the same service from Cable for 1/2 the price with no contract or equipment fees.
I will be switching to Optimum in a few months.
Verizon just does not value long term customers until they are gone.

STAY AWAY FROM Dualphone 4088 AND CHAT&VISION

The phone itself is ok, it just probably will stop working in few months and the seller skype recomends, Chat&Vision is a fraud, they just get the money and disappear. I have a broken phone and I spent weeks trying to have it replaced, but is impossible, they don't even reply to email.
Just do yourself a favor and don't ever buy anything from chat&vision ever!!!

Hi simonebruno,
I am sorry to hear of your experience with our company.
May I ask if you have checked your junk folder? It might be that our email was diverted there which has been the case for some of our customers especially those using a work email. If our emails are being diverted to your junk folder, kindly add domain "ChatandVision" to your mail box whitelist.
Should you not have received an email reply, simply provide me with your order number? I will review your case and come back to you as soon as possible.
Kind regards,
ChatandVision Ltd.

Charged for no service - STAY AWAY FROM BT THEY AR...

Ok so I decided to sign up for BT Infinity and tv package with BT sports in January. Was due to be installed on 23/01/2015.
I booked a half day off work for the installation and was impressed when the landline engineer called at 1.30pm. He told me that he was only doing the landline and another engineer would probably be out to do the TV.
Landline engineer worked away on the line and about 2.00pm I had a call from the TV engineer to say there was a fault in the line so would not be installing my tv. When I asked when he could install it he just said I don't know. From his attitude I could tell he wasn't bothered it was a Friday after noon so he just wanted to go home.
I was really annoyed with this as I had picked the Friday specifically and waited 3 weeks for installation for that Friday. I rang BT and asked them what was happening, I asked if he could come out on a Saturday to install the TV but I was told no they dont do Saturday installations. So I decided I wasnt going to go ahead with my installation and cancelled my order.
I was told to tell the landline engineer to leave as I was cancelling. I spoke to landline engineer and told him what I was doing. He then said he would speak to them as he was at the box the same time as the TV engineer and he didnt see any fault. The engineer spoke to customer services and told them I was cancelling my order.
As far as I was concerned that was it. My order was cancelled I was getting my refund of £90.71 and I would receive a bag to send the equipment back.
In February I received a bill for £22.41, I rang customer services as I still hadn't received my £90.71 and now they were billing me for a service I didn't ever have.
Result of call I got my £90.51 back and heard no more, great I thought that was easily sorted.
Wrong in March I got a final reminder for payment of £22.41, again I rang the lovely people in customer service and spoke to a very confused man who kept asking why I was being billed, this I thought was very amusing as that was my question to him. He said leave it with him and he would call my number back in 30 minutes. Guess what 30 minutes no call.
In my stupidity I assumed it had been sorted.
Last week I get a message from BPO to say ring this number immediately regarding BT. I rang the number and was put through to the most arrogant and ignorant woman I have ever had the misfortune to speak to.
I tried to explain my situation but she kept talking over me and in the end she said tough I was being billed for BT Sports as this should have been cancelled seperately. I told her noone ever explained that to me in all my communications with BT and she wasnt interested just advised me to pay up.
So today I rang BT to ask why this had gone to collections and what was my bill of £22.41 for. The nice lady told me she would look into it and transferred me to another nice lady. The 2nd nice lady said I should have contacted them before today!! I said I did and nothing happened. She explained that the £22.41 was for my landline charge. When I said I cancelled the day of the connection she said I needed to ring the nice people in BPO again as there was nothing she could do.
So now I have an outstanding bill of £22.41 plus admin fees of £5.60 from BT for nothing. BT think I just need to pay it and go away. Well as you can imagine I am fuming.
DO NOT USE BT AS THEY ARE THIEVES.

@dmcnamara087
Please use the 'contact the mods' link in my forum profile under the 'about me' section to send in your details. You can find the link by clicking on my username.
Thanks
Neil
BTCare Community Mod
If we have asked you to email us with your details, please make sure you are logged in to the forum, otherwise you will not be able to see our ‘Contact Us’ link within our profiles.
We are sorry but we are unable to deal with service/account queries via the private message(PM) function so please don't PM your account info, we need to deal with this via our email account :-)
If someone answers your question correctly please let other members know by clicking on ’Mark as Accepted Solution’.

Hi every time I navigate to a new page on facebook, I get the same confirmation message, Are you sure you want to navigate away from this page? Press OK to continue, or Cancel to stay on the current page. What I want to know is how to stop this message

When I click on a navigation button, a message box appears asking if I am sure I want to navigate away from this page.

This issue can be caused by Facebook gadgets. 
You will have to check that out by removing each of them until you find the culprit. 
If you added or updated gadgets recently then start with those.
See:
* [[Troubleshooting extensions and themes]]

When I use Firefox, if I want to move from one page to another, I get this: "Are you sure you want to navigate away from this page? Press OK to continue, or Cancel to stay on the current page.", OK doesn't always take me to where I wanted to go.

Anytime I want to click on one page to move to another I get this question. Most of the time, it doesn't take me anywhere. I cleared everything. It didn't make a difference.

This issue can be caused gadgets on the Facebook page. 
You will have to check that out by removing each of them until you find the culprit. 
If you added or updated gadgets recently than start with those. 
See:
* [[Troubleshooting extensions and themes]]

Sisoftware Sandra: Is there a reason to stay away from this software?

Similar Messages

Maybe you are looking for