Site to Site Crash After rebooting 5505 firewall
Hi Guy's,
im new over here and did'nt see and thread on the subject...
tried to google it but alas ... not answer
every now and then when things seems to not work over the firewall (like VPN) in the office we reset the firewall and the homeVPN is
working again.... BUT
we have Site to Site with another office thats generally works great.. it stops working after the reset and we have to insert the shared secret all over again in my office side (not the remote office site it stays ok over there)
i use ASDM 6.2 for ASA and it runs over ASA5505
if anyone have any clue ill be more then happy..... if you have any questions just ask and i'll give INFO
thanks in advance !
Hey Tom,
Can u please more elaborate your problem and provide the configuration .
Thnaks & Regards
Vishaw
Similar Messages
-
Video Drivers in Windows 7 64 bit cause Windows to crash after reboot
I have a Mac Mini mid 2011, I installed Windows 7 64 bit through Bootcamp. After the install I install the Mac drivers. I have narrowed it down to the video card drivers are causing Windows to crash on reboot. Are there other drivers I can use? Am I doing something wrong?
Thank you in advance for any help or advice.I have an imac
I have an magic pad (same thing as the touch pad on a macbook really)
I have an usb mouse I use both in windows and osx
if your trackpad somehow was registered as actived for some reason it would seem as if it was the mouse
had some *** situations both in windows and osx when my cat sit on the magicpad -
Firefox crashes after reboot of pc.
Hello, my firefox crashes every time when i turn on my pc and start the browswer. Then it works fine. But after reboot it does it again.
bp-c541ffc2-1eb3-4d34-97c4-334872140915This looks like it is crashing in an rpm file of your system, but there are also comments of others who have had also experienced this crash and they were looking at flash sites or their email. (not much else there) Are you also accessing a flash site?
If so, you can try to disable hardware acceleration in flash or check out to make sure the drivers are up to date: [[Upgrade your graphics drivers to use hardware acceleration and WebGL]] :
Some problems with Flash video playback can be resolved by disabling hardware acceleration in your Flash Player settings. (See [[Flash Plugin - Keep it up to date and troubleshoot problems|this article]] for more information on using the Flash plugin in Firefox).
To disable hardware acceleration in Flash Player:
#Go to this [http://helpx.adobe.com/flash-player/kb/video-playback-issues.html#main_Solve_video_playback_issues Adobe Flash Player Help page].
#Right-click on the Flash Player logo on that page.
#Click on '''Settings''' in the context menu. The Adobe Flash Player Settings screen will open.
# Click on the icon at the bottom-left of the Adobe Flash Player Settings window to open the Display panel. <br/> <br/>[[Image:fpSettings1.PNG]] <br/>
# Remove the check mark from '''Enable hardware acceleration'''.
# Click '''Close''' to close the Adobe Flash Player Settings Window.
# Restart Firefox.
This [http://www.macromedia.com/support/documentation/en/flashplayer/help/help01.html Flash Player Help - Display Settings page] has more information on Flash Player hardware acceleration, if you're interested.
Does this solve the problem? Let us know. -
2 sites in particular when I go to stream old TV shows, my movie site is ok, youtube is ok, all plugins are up to date, I've reset firefox, rebooted and all that regular stuff but still these 2 sites won't stream my video
now it is all the links on the given sites, I've tried everything, maybe it is related to the given 2 sites, one being 'watchseries.ch' I don't know, all input is appreciated. At this point I may just wait a day or two before trying anything else and see if it is these particular sites.
-
Compaq presario CQ57, -339WM Notebook PC, i was referred to techcenterstarup, crash after rebooting
My compaq presari CQ57-339WM, windows 7 home premium. I had and initial crash, 'could not find boot file' and was referred to techcenterstartup. i check out some of the tips handed to other users and had gotten it restarted. i had made a startup disc from my desktop which was windows 7 64bit. i think this eventually helped, but after restarting and running memory and diagnostic checks numerous times it started up and went down several times. The last time i got it started and booted i removed several folders of information to a flash drive. I was able to make a startup disc from the laptop, then proceeded to update and run norton 360 so i could get the antiviral protection. It ran for some time then froze. i eventually shut the laptop down but now it won't startup again not even using the disc. it is saying " no partition." I don't have a backup of this laptop.
Hello 1eye,
Welcome to the HP Forums!
I understand your notebook does not start up, saying there is not partition.
Given the information you have provided this all could stem from the Boot MGR being corrupted. I see you've made startup discs but have you run a system restore, system recovery, or startup repair?
You may still be able to access the HP Recovery Manager by repeatedly tapping the F11 key while the notebook turns on, which gives you access to these three tools.
If Boot MGR is missing or corrupted the easiest way to get it back is reinstalling the Windows operating system. The recovery media and recovery drive will not do this, you will need a copy of the Windows DVD or an ISO image you can download and burn to a DVD. Be careful not to format the recovery drive when reinstalling so you can run the recovery after to restore your pre-installed software, and that this will return the notebook to its original factory condition.
Hopefully this helps!
Please click the "Kudos, Thumbs Up" at the bottom of this post if you want to say "Thanks" for helping!
Please click "Accept as Solution" if you feel my post solved your issue, it will help others find the solution.
The Great Deku Tree
I work on behalf of HP. -
Lightroom 5 crash after reboot on mac, will not open
I was using lightroom yesterday and it was running ok, went to synch a folder I had been doing final edits on it photoshop.
I stopped using the computer to watch the game and this morning when i try to open lightroom 5, creative cloud and it won't open, crashes before it even opens.
I logged out of creative cloud twice and logged back in, still won't open.
This Is Info I have on my MAC
Mac OS X 10.7.5
Model Name: iMac
Model Identifier: iMac12,2
Processor Name: Intel Core i7
Processor Speed: 3.4 GHz
Number of Processors: 1
Total Number of Cores: 4
L2 Cache (per Core): 256 KB
L3 Cache: 8 MB
Memory: 8 GBWell that did it. I had to manually hack AE CC to make it work with my Video Card and now it works just fine.
Fast Draft:
Available
Texture Memory:
818.00 MB
Ray-tracing:
GPU
OpenGL
Vendor:
NVIDIA Corporation
Device:
NVIDIA GeForce GTX 670 OpenGL Engine
Version:
2.1 NVIDIA-8.12.47 310.40.00.05f01
Total Memory:
2.00 GB
Shader Model:
CUDA
Driver Version:
5.0
Devices:
1 (GeForce GTX 670)
Current Usable Memory:
3.31 GB (at application launch)
Maximum Usable Memory:
4.00 GB
I used these instructions on how to do it. http://www.vidmuze.com/how-to-enable-gpu-cuda-in-adobe-cs6-for-mac/
Obviously Adobe has not properly activated the ability to activate your own cards in AE yet. Come on Adobe! -
Understanding 5505 firewall-site to site and internet traffic
Hi,
My question is mutli-faceted. I apologize for the lengthy intro here but i think the info is necessary to understand where I am headed in this.
I am new to the cisco 5505. I have had very limited exposure to a 5510 that was preset. I have managed to make modifications to it here and there, but dont completely understand how it was put together. I learn by watching, listening, and gleaning what I can from others. I have had no formal training in CLI, but I have learned some of the commands. I know enough to be dangerous, but I respect my limitations.
That being said, I have been charged with setting up a 5505 at a remote site. I need to accomplish several things. Our ultimate goal is to use this device as a site to site with the 5510 at the corporate office. However, I need to accomplish this in baby steps, test, test real users and then maybe convert in full. Where I could outsource this in its entirety, that would preclude me from learning so I can address this in the future on my own.
We need to have this in place by the end of February 2013.
Currently the remote site is connected via a very slow (by todays standards) T1 line on a MPLS. Stable. Works, but slow. All internet traffic as well as work traffic is routed through that connection. We have added a 50mb cable connection (with static ips) to the office. First we want to set up the 5505 so that it can be used as follows:
1, Internet traffic can be routed out through this device and all other "work" traffic routed through the MPLS.
2, Test using this connection as a route out to the internet AND use it as a site to site VPN connection to the home office. (or anyconnect vpn)
I need to be able to have users in both environments. IE, some still using step 1 and some starting to use and test step 2.
3, long term, use this as the main connection per number 2, but add the IP address so that if the cable connection drops, the office can access internet via the VoIP T1 line as a life line.
In all cases, I dont want internet going through the home office as it currently is traveling.
I have done a lot of searching but so far have come up empty with answers.
Question 1: (This one probalby shows my ignorance the worst) - in using the 5505 firewall, will it segregate normal internet traffic from the VPN traffic when used by the workstation? Using the Gui, I didnt see where this was necessarily happening. Do I need to use CLI language (and what) to make this happen? Or is that a basic function that happens during the setup of the firewall using the GUI. Do I need to do some sort of "split tunneling"?
Question 2: Do I use this device as the Default gateway for both step 1 and 2/3) for normal use and then change the gateway on the Pcs to the VoIP network during emergency use,(that would bypass the firewall though or is there a way to have it route to that router if there is no connection through the Outside port? Or as long as I have some access to the device, can I make a change remotely to help accomplish this failsafe?
Question 3: We have 25 Anyconnect VPN licenses. Should we use these and not the Static site to site, if so, why or why not? They dont need to be used at all.
Question 4: In setting up the VoIP line for backup, would using that on the "DMZ" connection help in making this viable so that the device could still ultimately control the internet traffic?
Question 5: In setting up the VPN connections, unless i am getting the two methods confused, I will need the 5505 to hand out IP addresses for the vpn connection. I see in using a class c schema that i can use 92.168.0.0 to 192.168.255.0. So for instance, I could use 101.1.20.0 for the inside network Vpn addresses?? I need to stay away from 192.168.0.0 networks as we use that in our normal structure.
Reasons for setting this up:
Slow speeds over the T1.
increasing demand for Skype, Video conferencing etc that the T1 pipe couldnt adequately handle
Lack of backup pathways for downed connections - ie, backhoe chopping through wire at a construction site).
I read through the Getting started guides on both the 5510 and the 5505 and feel I can likely get the site to site setup (I have a list of all the Ip addresses i need for inside networks and outside networks etc.
additional notes:
I have to email ATT anytime I want a change made on the MPLS router, so doing as little to that as possible would be good.
I will be onsite for testing at the end of February and will have direct access to the home office via other methods to work on the asa5510 if any additional work needs to be done on it once i am onsite.
Thanks for taking the time to read through all of this. please forgive my lack of knowledge...
DaveThanks for getting back to me and so quickly!
1) I am not sure if I understand the “ACL” portion of your question, but this is how I want to access info via the VPN tunnel:
192.168.D.0 inside(NJ) to outside 5505 - 12.175.X.X to outside 5510 - 12.200.X.X to inside network (HQ)192.168.X.0. Routes are needed to find subnets 192.168.A.0, 192.168.B.0 and 192.168.C.0. The default gateway to those subnets right now is: 192.168.X.XX4 inside of HQ. This would be so that the NJ office could find resources of the other offices if needed. This will change as we wean off the MPLS. Inside the ASA 5505, the IP addresses are 192.168.D.0 for data, 10.X.X.0 for the Phone system. All other traffic would be sent out through the internet. Phone system uses the XOcomm conection to route phone traffic.
2) I did some reading on SLA. Thanks for pointing that out. For purposes of learning here, I am showing this as 12.175.XXX.XXX for Comcast and 12.200.XXX.XXX for XO comm.
4) I guess I would use an Outside 2 as that makes sense, in description, I would label them “ComCast” for outside 1 and “XOcomm” for outside 2.
5) I am still not sure I understand this part. Are additional IP addresses needed for the Site to site VPN to talk to the local hosts, or will it use the IP addresses assigned by the local server?
Next Steps
1- Configure the ASA5510 for the 5505 connection
2- Configure the ASA5505 for the 5510 connection
3- Configure SLA for Comcast and XOcomm outside connections
4- For this I need help….I think this is from step 1, but I need help to configure the internet to be segregated via my question from #1. Have I given enough information to do so? Please advise on ACL entries, and route statements needed so that NJ can talk to all the offices when using this connection, not just the Headquarters.
Thanks
dave -
Site "crashes" when attempting to return to inbox after full scan and numerous crash reports.
Problem just began on 1/25/13. Can view any site on hotmail window or web browser. When finished with site and attempt to return to Firefox site by either X in viewed site or back arrow site crashes and comes up with a crash report site.
I have been sending reports and then attempting to reconnect using reconnect. No solution.
I now cancel reconnect to return to Firefox Mozilla and then hit Hotmail in Most viewed.
Very clumsy.
Please advise simple and easy to UNDERSTAND for non teckie.
thanksI was able to enter "about crashes" it referred me back to your directions about an "address bar".
You have to be very simple with me. I have entered the requested information on every place I could on your web browser with no joy.
Where exactly on you site do I enter "about crashes"?
The "address bar" is not noted on my computer or in any help source that I have attempted to find. Please bear with me, I am just a user and not a skilled one at that. I enter sites wherever I can get results.
As an afterthought, your web browser only shows 3 or 4 places to enter requests:
1. standard web addresses
2. search requests
3. Foxfire requests (in center of page).
Again I have tried all 3 with no joy and a lot of frustration. My research shows that the requested information would be very helpful but does not tell me how to access (for "dummies")
thanks again -
WLAN AutoConfig Service crashes 3 or 4 times after you first login after rebooting?
Hi,
My lenovo came with windows vista - I upgraded to 7 when I got a chance. I have W7 Professional. I have all the Lenovo drivers installed except access connections. I don't like the tool. Anyways, Windows manages my wireless adapter. I have the weirdest issue -- right after I login after rebooting, the service "WLAN AutoConfig" crashes 3 or 4 times in sucession any time something tries to access the net. If you restart it enough times, it eventually stays up and never crashes again until you reboot. Also, the fancy aeropeek stuff crashes too. The task bar becomes non-transparent. That eventually recovers as well.
I have another t61 thru my work running w7 and it doesn't have this issue. The difference between the two of them is mainly that it has the intel based wifi card instead of the atheros based one.
In the event log, I see:
The Windows Audio Endpoint Builder service terminated unexpectedly. It has done this 2 time(s). The following corrective action will be taken in 120000 milliseconds: Restart the service.
The HomeGroup Listener service terminated unexpectedly. It has done this 1 time(s). The following corrective action will be taken in 60000 milliseconds: Restart the service.
The Network Connections service terminated unexpectedly. It has done this 2 time(s). The following corrective action will be taken in 100 milliseconds: Restart the service.
The Program Compatibility Assistant Service service terminated unexpectedly. It has done this 2 time(s). The following corrective action will be taken in 60000 milliseconds: Restart the service.
The Superfetch service terminated unexpectedly. It has done this 2 time(s). The following corrective action will be taken in 60000 milliseconds: Restart the service.
The Remote Desktop Services UserMode Port Redirector service terminated unexpectedly. It has done this 1 time(s). The following corrective action will be taken in 60000 milliseconds: Restart the service.
The WLAN AutoConfig service terminated unexpectedly. It has done this 2 time(s). The following corrective action will be taken in 60000 milliseconds: Restart the service.
then I see this later after a bunch of them have restarted
The Offline Files service terminated unexpectedly. It has done this 2 time(s). The following corrective action will be taken in 300000 milliseconds: Restart the service.
The HomeGroup Listener service terminated unexpectedly. It has done this 2 time(s). The following corrective action will be taken in 60000 milliseconds: Restart the service.
The Network Connections service terminated unexpectedly. It has done this 3 time(s).
The Program Compatibility Assistant Service service terminated unexpectedly. It has done this 3 time(s).
The Superfetch service terminated unexpectedly. It has done this 3 time(s).
The Distributed Link Tracking Client service terminated unexpectedly. It has done this 2 time(s). The following corrective action will be taken in 300000 milliseconds: Restart the service.
The Remote Desktop Services UserMode Port Redirector service terminated unexpectedly. It has done this 1 time(s). The following corrective action will be taken in 60000 milliseconds: Restart the service.
The Desktop Window Manager Session Manager service terminated unexpectedly. It has done this 2 time(s). The following corrective action will be taken in 300000 milliseconds: Restart the service.
The WLAN AutoConfig service terminated unexpectedly. It has done this 3 time(s).
The Portable Device Enumerator Service service terminated unexpectedly. It has done this 2 time(s). The following corrective action will be taken in 300000 milliseconds: Restart the service.
The Windows Driver Foundation - User-mode Driver Framework service terminated unexpectedly. It has done this 2 time(s). The following corrective action will be taken in 300000 milliseconds: Restart the service.
Has anybody encountered this? If so, did you find a fix?Also, I noticed this thread on Microsoft's site -- should I try disabling ipv6?
http://social.answers.microsoft.com/Forums/en-US/w7network/thread/c9605d54-7d4d-4e8c-83ae-4d3d287df2...
I don't use it anyways. -
A while back I designed a .php / MySQL site in DW8. The site
included DW8
add, edit, and delete server behaviors.
I've since upgraded to CS3
Today I was called on to edit the site. When I tried to open
any page that
contained the add, edit or delete server behavior CS3
crashes. The rest of
the pages open fine in CS3.
If I go on-line all of the pages work fine and there is no
problem using
them. I can open them in DW8 but not CS3.
Any ideas as to the problem?
JeffWorked like a charm.... Thank you Alan
So, Does this mean that I will now have to delete the
"WinFileCache-AD76BB20.dat" file twice a year?
I guess its a small annoyance for such a essential app.
Jeff
"Alan" <[email protected]> wrote in
message
news:C55993DB.3176C2%[email protected]..
> as a guess- it may be the daylight savings time issue.
>
>
http://kb.adobe.com/selfservice/viewContent.do?externalId=kb402776
>
> Dreamweaver CS3 crashes after Daylight Savings Time ends
>
> Issue
>
>
> Adobe Dreamweaver CS3 crashes when working with certain
PHP or ASP files
> in
> Code view or Design view after the clock goes back one
hour, when Daylight
> Savings Time ends. The crashes only occur when selecting
certain lines in
> Code view, or selecting certain objects in Design view.
The crashes only
> occur in files that have PHP or ASP code, intermingled
with HTML code. The
> crashes do not occur in Dreamweaver 8 or earlier (Ref.
229536).
>
>
> Reason
>
>
> The Dreamweaver CS3 WinFileCache-AD76BB20.dat file has
been corrupted by
> the
> time change.
>
>
> Solution
>
>
> 1. If Dreamweaver is open, quit the application.
> 2. Delete the WinFileCache-AD76BB20.dat file from the
Dreamweaver user
> configuration folder. Note that on Windows, the
Application Data and
> AppData
> folders are hidden by default, so verify that your
Windows Explorer folder
> options are set to View Hidden Folders. The location of
this file is as
> follows:
> * Dreamweaver CS3 on Windows Vista:
> C:\Users\[username]\AppData\Roaming\Adobe\Dreamweaver
9\Configuration
> * Dreamweaver CS3 on Windows XP:
> C:\Documents and Settings\[username]\Application
Data\Adobe\Dreamweaver
> 9\Configuration
> 3. Restart Dreamweaver.
>
>
> --
> Alan
> Adobe Community Expert, dreamweaver
>
>
http://www.adobe.com/communities/experts/
>
>
> -
I am running 10.6.8 and using iweb for my web site. After several SEO analysis they all indicate I need H1-6 header tags. After looking at the source code I see there are none in iweb. Are they necessary to add? Why would one add these tags and how do I add H Tags to iweb? And are there examples to look at? I am slowly learning about simple web design and assumed that iweb was stand alone without having to write code. Is this one of the reasons iweb is no longer supported? Thanks for looking at this!
A simple text page like this:
Heading
sub heading
text paragraph ....
Is traditionally represented by html tags like:
<h1>Heading</h1>
<h2>sub heading</h2>
<p>text paragraph ... </p>
I would guess that the use of h1-h6 tags helps search engines to understand the structure of a page as the tags imply a certain structure.
This can be compared to more generic tags like <div> that could represent any kind of content - and may be what iWeb uses (you'll have to check yourself).
I would generally recommend that you use some kind of up to date blog/site building tool, perhaps Wordpress or Squarespace (I haven't used either one myself) that support current web technologies - this should reduce your SEO issues and make it easier to properly support mobile/tablet users. -
I desperately need your help. I was working on iMovie last night when the thing froze up on me. I've tried rebooting. I've tried reinstalling the apps. No change. I can play some of the files- although I can't tell which ones will play until they magically appear. I can't get into the project library or the event library. The bar that lets me scroll through the clips is gone. Even when I can get something to play the whole system crashes after a couple of minutes and generates a "problem report" that says "iMovie Quit Unexpectedly". This all started when I was adding cutaways- and one clip just would not load. After I tried several times everything froze up. Have you ever heard of something like this? Maybe I pushed a button or somehow changed a setting? Maybe some of the video is corrupt? What do you recommend?
Thanks for any advice you can offer!I have tried all the above and nothing seems to work. Any other suggestions?
-
Hi,
I made the site in iweb, and uploaded it to godaddy. The site crashes in Safari when I click through the pages, making it unusable on any computer for about 5 minutes (but no problems at all using Firefox and IE.)
The URL is http://sanafit.net/Aron/home.html
I would really appreciate any help. Thank you.HI,
See my suggestions here.
http://discussions.apple.com/message.jspa?messageID=10903895#10903895
Carolyn -
How do you change your intial bc template selection under site options after you click finish
how do you change your intial bc template selection under site options after you click finish
You cant. BC doesnt have a theming system like Wordpress or Joomla. The template is fixed and switching templates at this stage is not an easy feat.
-
Adobe InDesign CS5 needs plugs ins, but how? Adobe InDesign CS6 won't open says OS problem. Adobe upgrade site crashes on me.
You might ask in InDesign to learn how to install plugins
>says OS problem
What IS your operating system, and which exact version?
Is the link below where you are starting for upgrades?
All Adobe updates start here and select product, read to see if you need to install updates in number order, or if the updates are cumulative for the individual product http://www.adobe.com/downloads/updates/
Maybe you are looking for
-
Environment: 1 WFE on W2K8Ent x64 SP2 | 1 App Server on W2K8 Standard x64 SP2 | 1 Dedicated SQL Server 2008 R2 SharePoint 2010 Enterprise Edition I recently applied SP1 and the October 2011 CU (Server updates, not foundation) on both the WFE and th
-
Is the Apple's power adapter (AC to USB) compatible with the 5G? I have used a 3rd party power adapter with the iPOD mini, and it worked well. Now I have a 5G, and it cannot charge the 5G as the mini. Hate to spend another $30 for the Apple power ada
-
Search help to a field of a selection screen
how do we add a search help to a field of a selection screen..??
-
How to setup a Default Playlist to Airport but allows BYOD playlist override?
Sorry for the unclear description. Here is what I am trying to accomplish. I have my laptop or ipod playing a default playlist to my Airport express attached to my Stereo system. The music plays fine with no issues. I come into the house and want
-
Encore CS5 Hanging at Transcoding When Burning Transcoded Project to DVD Disc
Hi I'm a bit stuck and hope for some help. I have a NTSC DVD project, 4.1 GB in size, which has previously built to DVD Disc, and I have just tweaked a couple of the menu buttons, tried to build to disk again, and the process hangs at "Transcoding...