Smartctl reports errors. Is tehre a way to save disk?

I don't know why but I just made long smartctl test:
smartctl -d ata -t long /dev/sda
and the output:
smartctl version 5.38 [x86_64-unknown-linux-gnu] Copyright (C) 2002-8 Bruce Allen
Home page is http://smartmontools.sourceforge.net/
=== START OF INFORMATION SECTION ===
Model Family: Toshiba 2.5" HDD series (80 GB and above)
Device Model: TOSHIBA MK1234GSX
Serial Number: 27KLTKHBT
Firmware Version: AH001D
User Capacity: 120,034,123,776 bytes
Device is: In smartctl database [for details use: -P show]
ATA Version is: 7
ATA Standard is: Exact ATA specification draft version not indicated
Local Time is: Wed Dec 2 01:16:02 2009 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x80) Offline data collection activity
was never started.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 435) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 86) minutes.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000b 100 100 050 Pre-fail Always - 0
2 Throughput_Performance 0x0004 100 100 000 Old_age Offline - 0
3 Spin_Up_Time 0x0027 100 100 001 Pre-fail Always - 1614
4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 1288
5 Reallocated_Sector_Ct 0x0033 100 100 050 Pre-fail Always - 0
7 Seek_Error_Rate 0x000a 100 100 000 Old_age Always - 0
8 Seek_Time_Performance 0x0004 100 100 000 Old_age Offline - 0
9 Power_On_Hours 0x0032 076 076 000 Old_age Always - 9985
10 Spin_Retry_Count 0x0032 125 100 000 Old_age Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 1263
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 58
193 Load_Cycle_Count 0x0032 079 079 000 Old_age Always - 217767
194 Temperature_Celsius 0x0022 100 100 000 Old_age Always - 47 (Lifetime Min/Max 10/69)
196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 0
197 Current_Pending_Sector 0x0032 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0030 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0
220 Disk_Shift 0x0002 100 100 000 Old_age Always - 119
222 Loaded_Hours 0x0032 078 078 000 Old_age Always - 8844
223 Load_Retry_Count 0x0032 100 100 000 Old_age Always - 0
224 Load_Friction 0x0022 100 100 000 Old_age Always - 0
226 Load-in_Time 0x0026 100 100 000 Old_age Always - 322
240 Head_Flying_Hours 0x0000 100 100 000 Old_age Offline - 0
SMART Error Log Version: 1
ATA Error Count: 10 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 10 occurred at disk power-on lifetime: 3506 hours (146 days + 2 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
40 51 08 60 c1 97 e3 Error: UNC 8 sectors at LBA = 0x0397c160 = 60277088
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
c8 00 08 60 c1 97 e3 00 1d+00:10:47.956 READ DMA
27 00 00 00 00 00 e0 00 1d+00:10:47.956 READ NATIVE MAX ADDRESS EXT
ec 00 00 00 00 00 a0 00 1d+00:10:47.935 IDENTIFY DEVICE
ef 03 45 00 00 00 a0 00 1d+00:10:47.928 SET FEATURES [Set transfer mode]
27 00 00 00 00 00 e0 00 1d+00:10:47.928 READ NATIVE MAX ADDRESS EXT
Error 9 occurred at disk power-on lifetime: 3506 hours (146 days + 2 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
40 51 08 60 c1 97 e3 Error: UNC 8 sectors at LBA = 0x0397c160 = 60277088
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
c8 00 08 60 c1 97 e3 00 1d+00:10:41.160 READ DMA
27 00 00 00 00 00 e0 00 1d+00:10:41.160 READ NATIVE MAX ADDRESS EXT
ec 00 00 00 00 00 a0 00 1d+00:10:41.153 IDENTIFY DEVICE
ef 03 45 00 00 00 a0 00 1d+00:10:41.152 SET FEATURES [Set transfer mode]
27 00 00 00 00 00 e0 00 1d+00:10:41.152 READ NATIVE MAX ADDRESS EXT
Error 8 occurred at disk power-on lifetime: 3506 hours (146 days + 2 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
40 51 08 60 c1 97 e3 Error: UNC 8 sectors at LBA = 0x0397c160 = 60277088
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
c8 00 08 60 c1 97 e3 00 1d+00:10:34.385 READ DMA
27 00 00 00 00 00 e0 00 1d+00:10:34.385 READ NATIVE MAX ADDRESS EXT
ec 00 00 00 00 00 a0 00 1d+00:10:34.376 IDENTIFY DEVICE
ef 03 45 00 00 00 a0 00 1d+00:10:34.369 SET FEATURES [Set transfer mode]
27 00 00 00 00 00 e0 00 1d+00:10:34.369 READ NATIVE MAX ADDRESS EXT
Error 7 occurred at disk power-on lifetime: 3506 hours (146 days + 2 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
40 51 08 60 c1 97 e3 Error: UNC 8 sectors at LBA = 0x0397c160 = 60277088
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
c8 00 08 60 c1 97 e3 00 1d+00:10:27.615 READ DMA
c8 00 08 38 af 8d e3 00 1d+00:10:27.603 READ DMA
c8 00 08 60 98 89 e3 00 1d+00:10:27.592 READ DMA
c8 00 08 90 f5 92 e3 00 1d+00:10:27.587 READ DMA
c8 00 08 a0 97 90 e3 00 1d+00:10:27.577 READ DMA
Error 6 occurred at disk power-on lifetime: 3506 hours (146 days + 2 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
40 51 50 60 c1 97 e3 Error: UNC 80 sectors at LBA = 0x0397c160 = 60277088
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
c8 00 00 b0 c0 97 e3 00 1d+00:10:12.260 READ DMA
27 00 00 00 00 00 e0 00 1d+00:10:12.260 READ NATIVE MAX ADDRESS EXT
ec 00 00 00 00 00 a0 00 1d+00:10:12.252 IDENTIFY DEVICE
ef 03 45 00 00 00 a0 00 1d+00:10:12.244 SET FEATURES [Set transfer mode]
27 00 00 00 00 00 e0 00 1d+00:10:12.244 READ NATIVE MAX ADDRESS EXT
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Extended offline Completed without error 00% 9984 -
# 2 Short offline Completed without error 00% 6312 -
# 3 Short offline Completed without error 00% 3642 -
# 4 Short offline Completed without error 00% 3342 -
# 5 Short offline Completed without error 00% 15 -
# 6 Short offline Completed without error 00% 2 -
# 7 Short offline Completed without error 00% 0 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
My questions is is there a way to save disk? And is the information that I have 3506 hours left any near correct?

Thank you vacant for your reply. That is great news! My disk will last on

Similar Messages

SCCM 2012 R2 reporting error: "The DefaultValue expression for the report parameter 'UserTokenSIDs' contains an error: A specified logon session does not exist. It may already have been terminated. (rsRuntimeErrorInExpression)"

Hi,
I have two SCCM environments under same active directory domain and one service account have been used for SCCM configurations on both the environments (QA and PRODUCTION). I am facing similar error as mentioned above while trying to fetch reports on
PRODUCTION site, but the QA site is working fine, though same service account have been used for configuring both. While looking at the reportserverservice_<date> log on my Production DB server i see the following error
"processing!ReportServer_0-3!2124!01/02/2015-09:09:30:: e ERROR: Throwing Microsoft.ReportingServices.ReportProcessing.ProcessingAbortedException: , Microsoft.ReportingServices.ReportProcessing.ProcessingAbortedException: An error has occurred during
report processing. ---> Microsoft.ReportingServices.ReportProcessing.ReportProcessingException: Cannot read the next data row for the dataset DataSet1. ---> System.Data.SqlClient.SqlException: Conversion failed when converting the nvarchar value 'Override
Default' to data type int."
My DB and SCCM primary site are different and the reorting services point is installed on remote DB server. Please help me resolving the issue.
Troubleshooting performed:
1.Disabled the registry key 'EnableRbacReporting' from HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\SMS\SRSRP to 0 and then restarted SSRS service and the reporting worked for some minutes after that the registry key reverted back to 1 automatically and
reporting started throwing errors again.
2. Checked with the permissions on DB whether or not 'sysadmin' role is assigned to the SCCM service account.
3. re-registered the SQL management Provider WMI class.
mofcomp.exe “C:\Program Files (x86)\Microsoft SQL Server\110\Shared\sqlmgmproviderxpsp2up.mof”

Hi All,
Finally found exact solution to the reporting error.
Error: while launching SCCM reports (both from Console and web based) an unexpected error occured with error message as "The DefaultValue expression for the report parameter ‘UserTokenSIDs’ contains an error: A specified logon session does not exist.
It may already have been terminated. (rsRuntimeErrorInExpression)"
Solution: This is password replication issue for the domain account used to configure reporting services point in SCCM. If your SQL SSRS reporting services instance and databse runs with local default account whereas the reporting services point on SCCM
primary site is configured with domain account, (As in My case) you need to perform the following in order to get rid of the error.
Launch 'Reporting Services Configuration Manager' from the SQL SSRS box(either Local or Remote), Connect to Report Server Instance->Go to 'Execution Account' tab->Specify the 'Execution Account' as domain account and password which is used to configure
Reporting Services Point in SCCM Primary Site, and then click apply.
Now Lauch the report either way (Web based or from Console), the error will disappear and all your default reports will execute perfectly as before.

Crystal Report Error when Viewing in VB6

Post Author: aquiintac
CA Forum: General
I'm using crystal report and vb6. My first problem was how to change the data source location of the crystal report. I found away by using this: crxReport.Databases.SetDataSource rsReport
but I'm having an exception report : "The exception unknown software exception (0xe0434f4d) occurred in the application at location 0x77e55e02"The report shows for some time but after opening several reports the error message occurs.This is my scenario:"I'm using a udl for my connection. I have two databases namely TK and TK_MCC. TK is for other company and TK_MCC is for the subsidiary company. I used TK database when I created the crystal report. I used the setdatasource to pass the recordset to change the datasource location of the crystal report. So even if they change the database TK to TK_MCC they can still access the report. But when I did the setdatasource there was an exception report. (The exception unknown software exception (0xe0434f4d) occurred in the application at location 0x77e55e02)"Before it was working fine when I don't have to change the database. But when I used crxReport.Database.SetDataSource rsReport this error happened.By the way, i tried it also in another computer (just installed the program) but the error message was different. The other error was error28 out of stack space and sometimes the program closes by itself.Can someone help me on this...Thank you very much.

Seems to be working now.
I upgraded CR and adobe.
Edited by: RolandWorms79 on Sep 7, 2009 10:52 AM

BO 4.1 report errors out

Please help me out with below issue
We have a .net web application accessing BO 4.1 CMS server with SP2 through BO SDK for .net to display existing reports from BO Server and we have below environment
QA Setup =>   .NET app server 1 + BO Server 1
PROD Setup => .NET app server 2 + BO Server 1
in above combination BO reports works as expected from PROD setup but getting below in consistency while accessing the reports from QA box
1. Getting "Problem with server's security certificate" from QA instance of the app but the same BO server works fine from PROD. (verified the server certificate and its valid for another 4 years)
2. after showing java applet window for a while report errors out and just display JRE runtime error without giving much debugg info
3. browser profiler shows data getting downloaded on the client browser but still errors out
we are generating the token as shown below and direct report URL ( with .jsp to call apache server) is passed to load the report to an iFrame.
        if (!ValidateToken(currentToken))
            SessionMgr ses = new SessionMgr();
            EnterpriseSession es = ses.Logon(AppSettings.BusinessObjectsUser, decrypter.DecryptString(AppSettings.BusinessObjectsPass), AppSettings.BusinessObjectsUrl, "secWinAD");
            LogonTokenMgr myToken = es.LogonTokenMgr;
             return myToken.CreateLogonTokenEx("", 1440, -1);
Could you please suggest how to make this work.
Regards
ANoop

Hi All,
Attaching the snapshot of webi report error returned on the application and trace returned on IE 9 developer tool
1. webi report error
2. Trace returned on IE 9 developer tool
as the same BO server render the webi report on other asp.net application with same configuration, is there any way to find either from BO server or the location machine why the report error out... ?

Reporting errors or exceptions back to the caller

I'm u sing OracleAS 10.1.3 and I'm exposing some of my PL/SQL procedures as web services. I was wondering what the convention is for reporting errors back to the caller. I read a little bit about Soap faults and some lack of support in the current JDev release.
Are soap faults the standard way of reporting handled exceptions? What about returning a record like:
   type r_ws_response_string is record (
      result          varchar2 (4000),
      return_code     number,
      error_message   varchar2 (4000)
   );... and having the caller check the return_code. Bad idea?
Any resources you can point is is appreciated (books/sites).
-Vahid Pazirandeh

Hi Toby,
Yes, I've come up with a working solution.
Essentially, I've made use of PL/SQL's OUT parameters and always reporting a status to the caller. At minimum, any procedure or function that I expose as a web service will have two out parameters: status, error_msg. The benefit of having a status being returned is that the caller can build logic based on different problems encountered, rather than just saying "an error occured". The error strings that you define are textual error codes, so they shouldn't change once you decide on an API.
The caller will always check for the value of status, if it is not 'SUCCESSFUL', then something is wrong. They can then log the value of error_msg so that their developers can figure out what went wrong later.
What's also nice is that the XML that's generated by JDeveloper looks clean when we're using one or more OUT params.
I don't know what the best way is to deal with this problem, but this works for me. :) Here's an example:
g_status_success        := 'SUCCESSFUL';
g_status_bad_password   := 'ERROR_INVALID_PASSWORD';
g_status_file_not_found := 'ERROR_FILE_NOT_FOUND';
g_status_unknown_error := 'ERROR_UNKNOWN_EXCEPTION';
procedure give_me_file(password varchar2,
                       status out varchar2,
                       error_msg out varchar2,
                       file out blob)
is
begin
     if bad_password(password) then
          status := g_status_bad_password;
          error_msg := 'You entered the wrong password friend!';
          return;
     end if;
     file := get_top_secret();
     if file is null then
          status := g_file_not_found;
          error_msg := 'Your file could not be found';
          return;
     end if;
     status := g_status_success;
     exception
          when others then
               status := g_status_unknown_error;
               error_msg := 'An unknown error occured. Please file a ticket.';
end;Regards,
Vahid Pazirandeh

Reports Error Page 10g NullPointerException

We have created a JSP report that produces Excel output via method outlined in the example given in the HowTo:
http://otn.oracle.com/products/reports/htdocs/getstart/demonstrations/excel/index.html
The JSP runs fine under 9.0.2 iAS but when we moved the report to a 10g AS we get the following error:
Reports Error Page
Mon May 24 11:50:26 BST 2004
java.lang.NullPointerException
java.lang.NullPointerException
     at com.evermind.server.http.EvermindBodyContent.setCharacterEncoding(EvermindBodyContent.java:458)
     at com.evermind.server.http.EvermindPageContext.pushBody(EvermindPageContext.java:630)
     at oracle.jsp.runtime.OracleJspRuntime.pushBodyIfNeeded(OracleJspRuntime.java:1385)
     at examples.test._test1._jspService(_test1.java:55)
     at com.orionserver.http.OrionHttpJspPage.service(OrionHttpJspPage.java:56)
     at oracle.jsp.runtimev2.JspPageTable.service(JspPageTable.java:349)
     at oracle.jsp.runtimev2.JspServlet.internalService(JspServlet.java:509)
     at oracle.jsp.runtimev2.JspServlet.service(JspServlet.java:413)
     at javax.servlet.http.HttpServlet.service(HttpServlet.java:853)
     at com.evermind.server.http.ResourceFilterChain.doFilter(ResourceFilterChain.java:65)
     at oracle.security.jazn.oc4j.JAZNFilter.doFilter(Unknown Source)
     at com.evermind.server.http.ServletRequestDispatcher.invoke(ServletRequestDispatcher.java:604)
     at com.evermind.server.http.ServletRequestDispatcher.forwardInternal(ServletRequestDispatcher.java:317)
     at com.evermind.server.http.HttpRequestHandler.processRequest(HttpRequestHandler.java:790)
     at com.evermind.server.http.AJPRequestHandler.run(AJPRequestHandler.java:208)
     at com.evermind.server.http.AJPRequestHandler.run(AJPRequestHandler.java:125)
     at com.evermind.util.ReleasableResourcePooledExecutor$MyWorker.run(ReleasableResourcePooledExecutor.java:186)
     at java.lang.Thread.run(Thread.java:534)
Any ideas what could be causing the report to fail and ways to make the report run under 10g As?

Try adding charset to the content type
e.g:
<%@ page contentType="application/vnd.ms-excel;charset=ISO-8859-1" %>
- Vinayak

Conditional Display on Report error

hey,
can anyone suggest a way/workaround to catch a report error. when error occures, i'd like to display another report, just below, without errorneus columns ( Oracle Text score(1) this time )
report error:
ORA-20000: Oracle Text error:
DRG-50901: text query parser syntax error on line 1, column 1
how could i make this error conditional?
br,
Simon

Hi Simon - I have the same issue. Did you find a solution?
thanks,
Matt

I am currently running 10.7.5 on my macbook. I tried downloading Mountain Lion application...but it says 'error'',,,is there another way to upgrade my OS?

I am currently running 10.7.5 on my macbook. I tried downloading Mountain Lion application...but it says 'error'',,,is there another way to upgrade my OS?

First we need to know which one of the 9 different models of MacBook you have. To see which model you have go to the Apple in the upper left corner and select About This Mac, then click on More Info (and then System Report if you’re running 10.7 Lion). When System Profiler comes up check the Model Identifier and post it back here.
The Early 2006 model 1,1 Core Duo can only run a maximum of 10.6 Snow Leopard.
The models Late 2006 Core 2 Duos 2,1 through Early 2008 4,1 can only run a maximum of 10.7 Lion.
The Late 2008 model 5,1 Aluminum Unibody through the Mid 2010 White Unibody model 7,1 can run 10.8 Mountain Lion.

Financial Reporting Error - MaximumCalculationIterations

We currently encountered a Financial Reporting error that some default limits was exceeded. However we don't know why only this report has errors but not the others.
ERROR GridResult Unevaluated cells in report '/Finance/Report 1' within grid '\\\Grid3'. The following 2 cells were not evaluated: Row 3 Col 7 Row 5 Col 7 The maximum calculation limit of 5 was reached. Update the 'MaximumCalculationIterations' setting in 'fr_global.properties' if necessary.
By the way, any experience on how large this parameter can be set? The default is 5 and we intend to change it into 50 and see if the issue can be resolved.
Thanks a lot if you have some similar experience that can be shared.

If the Essbase server named in the message:
... Essbase Server at "*+server+*:1423"....
is not running, the message will occur. Start the essbase server and rerun the diagnostic

IF Condition in a PL/SQL Script give a report error.

Hello, Im German and I hope you can unterstand my Question.
First, I work with the HTML DB Version 1.6.0.0.0.87 and the Oracle Version 9.2.0.6.
I create a SQL Report, where a PL/SQL Script return the SQL Statement for the Report. This is my source-code, I have short it...:
Declare
sql_str varchar(2000);
sql_str_select varchar(1000) :=' select dim_sparte ... ';
sql_str_from varchar(1000) := ' from faktentabelle,dim_sparte ';
sql_str_where varchar(1000):= ' where and faktentabelle.zeit_id = :POPUP_ZEIT ';
sql_str_groupby varchar(1000):= ' group by dim_sparte.name, faktentabelle.zeit_id ';
Begin
If ( (V('POPUP_NETZGEBIET') is not NULL) and (V('POPUP_NETZGEBIET') <>
'Alle Netzgebiete')) THEN
sql_str_select := sql_str_select || ' ,dim_organisationseinheit.netzgebiet_name ';
sql_str_from := sql_str_from || ' , dim_organisationseinheit ';
sql_str_where := sql_str_where || ' and faktentabelle ... and
dim_organisationseinheit.netzgebiet_name = :POPUP_NETZGEBIET';
sql_str_groupby := sql_str_groupby || ' , dim_orga .... ';
End IF;
sql_str:= sql_str_select || sql_str_from || sql_str_where || sql_str_groupby;
htp.print(sql_str);
Return sql_str;
End;
This Script include a IF-THEN condition. The Condition is true and the sql-String-Variables are updatet.
I can get the string with htp.print() and the Statement is OK.
The report get a Error report error: ORA-1403: no data found. If I copy the printet sql String in a new Report Region with SQL String, the Report is OK. When I write IF(true) instead of IF( Condition) the Report is OK, too.
I try ist with Varibalen V(name) and with :name. Its always the same problem. I cant use IF-THEN-Else Conditions in a Script.
Please help me and say me what is the problem???
Thanks,
Simona

Hi Simona,
In the sql region below the region source see that you have " Use Generic Column Names (parse query at runtime only)" check and not " Use Query-Specific Column Names and Validate Query".
This error you usually get when you have a mismatch in your report heading.
Vivek
[email protected]

History report error: | An Exceptional Error occurred. Application exiting. Check the log file for error 5022

Hi all
I've got a error msg when try to generate a report using Cisco history report tool:
Error | An Exceptional Error occurred. Application exiting. Check the log file for error 5022
It only happens when choose report template: ICD_Contact_Service_Queue_Activity_by_CSQ_en_us.
User tried samething on other PC, it working fine.
only on user' own PC and only choose this report, error appears.
user runing windows 7 and do not have crystal report installed
tried reinstalled the software, doesn't work.
also tried this: (https://cisco-support.hosted.jivesoftware.com/thread/2041254) - doesn't work
then tried https://supportforums.cisco.com/docs/DOC-6209 - doesn't work
attached the log file.
thanks.

wenqianyu wrote:From the log file:Looks like you get a Login Window.Error message showed up after username/password be enteredThere is an error in the log: Error happened in comparing UCCX version and HRC versionYou may need to do a clean uninstall, download the Historical report from the server, and install it again on the PC.Does this only happen to one PC or to every PC with this application?Wenqian
I have completely uninstalled the HRC, and download from server install again -- still doesn't work with exactly same error.
this matter only happens on this PC, when user try same thing on other PC, it works.
so i think it not relate to server or account.

Report error: ORA-06502: PL/SQL: numeric or value error: character string b

I have a form which uses a customer form/report, drop downs etc..
the debug shows it running this statement
...Execute Statement: begin begin SELECT distinct initcap(RTRIM (LTRIM (e.surname, ' *0123456789-/:.?,'), ' *0123456789-/:.?,') || ', ' || RTRIM (LTRIM (e.first_name, ' *0123456789-/:.?,'), ' *0123456789-/:.?,' )) empname, e.ID bulk collect into wwv_flow_utilities.g_display,wwv_flow_utilities.g_value FROM dms.dms_employees@dmsprd e, dms.dms_employee_contracts@dmsprd ec WHERE e.ID = ec.emp_id and e.surname like '%%' AND :p75_date BETWEEN ec.start_date AND NVL (ec.end_date, :p75_date) AND e.brh_id = 3654 ORDER BY 1; end; end;
Then says
"report error: ORA-06502: PL/SQL: numeric or value error: character string buffer too small"
Any Ideas?
Thanks
Dean

Denes Kubicek wrote:
A select list is limited in size. I am not sure what the limit is but that is definitelly the case.The maximum size for the HTML generated for a select list is 32K.
86 options sounds on the low side to be hitting that limit, but there are other concerns to this as well. Scrolling through hundreds/thousands of options in a select list is a pain for users, and huge select lists produce bloated pages that impact load times and network bandwidth. That list of around 200 countries you find on many sites is about the sensible maximum length for a select list.
You should use popups.Indeed.

Report error:ORA-06502: PL/SQL: numeric or value error: character to number

The oracle application express environment is created by installing the HTTP Server on the windows server and the application express 3.2.1 components on the 11.1.0.7 oracle database on UNIX. The installation is successfully and have not seen any issues during the installation. After completing all the steps, when tried to login and click the application builder or workspace components, I see the error message
report error:ORA-06502: PL/SQL: numeric or value error: character to number.
This error message is seen on most of the pages when trying to accessed and not able to understand the reasons behind it. Its a brand new environment setup and not even presented to developers to test it.
Below error message is always seen when trying to access most of the components like application builder, schema comparison and some other tabs. Please advice
report error:
ORA-06502: PL/SQL: numeric or value error: character to number conversion error
Edited by: user589320 on Jun 9, 2011 5:17 PM

I think its better you use APEX 4.x version ratherthan using old version.
You will get more features and some bug fixes and also it's easy for you to get some help when you need.
* If this answer is helpfull or correct then please mark it and grant the points.

Report error:ORA-06502: PL/SQL: numeric or value error: character string bu

We face the above error in HTMLDB (APEX) application Ver 3.1.0. This occurs when we try to display more number of rows/records in drop-down list (LOV in tabular forms). We are able to display 200 records in LOV. When the list of records exceeds 230, we face the below error
report error:ORA-06502: PL/SQL: numeric or value error: character string buffer too small
the values listed in LOV are from tables (one of the columns in table)
Could anyone give us a solution?

Hi
As you are using a tabular form, you could actually do the following:
1 - In the tabular form column's attributes, set the following:
Display as: Select List (query based on LOV)
Display extra values: Yes
List of values definition: SELECT null d, null r FROM DUAL
2 - Add a new page item and set it to generate your select list
3 - Create an HTML region with no template and use the following for its source:
<script type="text/javascript">
function loadList(c, l)
var s = document.getElementsByName(c);
var lItem = document.getElementById(l);
var lLength = lItem.options.length;
var k;
var j;
var x = lItem.innerHTML;
var v;
var o;
var z;
for (k = 0; k < s.length; k++)
z = s[k];
v = z.value;
z.options.length = 0;
for (j = 0; j < lLength; j++)
o = new Option()
o.value = lItem[j].value;
o.text = lItem[j].text;
z.options[j] = o;
z.value = v;
if (z.selectedIndex == -1)
z.selectedIndex = 0;
loadList("f05", "P1_MGR");
</script>
(Change "f05" and "P1_MGR" as appropriate to your column and your new page item respectively)
Now, when you load the page, the select list contains a null entry plus the entry already on the database. The javascript kicks in automatically, loops through every entry in the "f05" column, copies the existing value, replaces the select list with the new page item version and sets its value to the copied value.
Your new page item could be in a DIV tag that has a style of "display:none" to hide it from view.
Andy

Report error: ORA-06502: PL/SQL: numeric or value error: NULL index table k

Hi everybody,
I have two Distinct Databases on two distinct servers. (Oracle Ent. Release 10.2.0.3.0 on AIX 5.3). After I install the latest patch last week, One of the APEX installation has some problems on Home>Application Builder Page. The error message is very random and
report error:
ORA-06502: PL/SQL: numeric or value error: NULL index table key value.
When i change the view (details to icons), everything goes to normal. This error message is reflected some of the pages (report region) of some of my applications randomly. When it appears in a report region, i deselect the order method of the region, the result is normal.
But the other APEX application on the other instance has no problem. It is a bug? or Should i re-install the APEX instance?
Thank you for your interest?
Gökhan ÇATALKAYA

No, but we have a reproducible test case now so we're working on it. See ORA-06502: PL/SQL: numeric or value error: NULL index table key value
Scott

Smartctl reports errors. Is tehre a way to save disk?

Similar Messages

Maybe you are looking for