Solaris 10 cannot mirror using SVM for SFV440 server

I have tried to use LVM to configure the c1t2d0s0 and c1t3d0s0 but fail.
Below are the commands I used:
#metadb -f -a -c 4 /dev/dsk/c1t2d0s7
#metadb -a -c 4 /dev/dsk/c1t3d0s7
#metainit -f d10 1 1 c1t2d0s0
#metainit -f d20 1 1 c1t3d0s0
#metainit d0 -m d10
(modify the /etc/vfstab file to /dev/md/dsk/d0 and /etc/md/rdsk/d0)
#init 6
After reboot the server, metadb are deleted. Cannot mount the /dev/dsk/d0.
I have 8 SFV440 servers total. 7 SFV440 servers with mother-board (p/n:
501-6910) cannot mirror. 1 SFV440 server with mother-board (p/n: 501-6344)
is wotking fine can use LVM to mirror the data disk. All the configuration
are same. (hardware and OS (Solaris 10 03/05)used)

Try the following commands:
First make sure that the metadb partitions are unmounted and big enough to hold the metadb's.
Second make sure both sides of the mirrors are the exact same size. Mirroring will fail if the 2nd half of the mirror is smaller than the first half.
I would then newfs and fsck the metadb partitions.
#metadb -f -a -c 2 /dev/dsk/c1t2d0s7
#metadb -f -a -c 2 /dev/dsk/c1t3d0s7
# make sure the metadbs exist
# metadb -i
#metainit -f d10 1 1 c1t2d0s0
#metainit -f d20 1 1 c1t3d0s0
#metainit d0 -m d10
(modify the /etc/vfstab file to /dev/md/dsk/d0 and /dev/md/rdsk/d0)
# check out to see if the one way mirror exists
metastat
#init 6
# Don't forget to attach the 2nd half of the mirror
# metattach d0 d20
# check to see that the mirror is syncing
# metastat

Similar Messages

Cannot use file for clustered server. Only formatted files on which the cluster resource of the server has a dependency can be used. Either the disk resource containing the file is not present in the cluster group or the cluster resource of the Sql Serve

Hi
Windows serv 2012 cluster on sql 2012 cluster with 2 instance. on works fine , Second instanc ewhen i try to creat DB a get this message.
Cannot use file for clustered server. Only formatted files on which the cluster resource of the server has a dependency can be used. Either the disk resource containing the file is not present in the cluster group or the cluster resource of the Sql
Server does not have a dependency on it.
CREATE DATABASE failed. Some file names listed could not be created. Check related errors. (Microsoft SQL Server, Error: 5184)
Any help please
kam
KAMEL

Hi Saurabh
Exactly I have SQL SERVER 2012
Failover Clustering in windows server 2012 with two nodes with
two instances and exactly I run them in the same server and each instance with
three drives Backup, Data and log.
KAMEL

Cannot find a report for SQL Server monitoring

We installed a SCOM 2012 environment recently and imported the SQL Server Management packs successfully. SQL Servers are being monitored.
However, in the reporting section, i cannot find a group for SQL Server Reporting. All other show up ( Active Directory, Appication Monitoring, Web monitoring, etc) Just none for the SQL Reporting.
Please help

Hi,
I assume that you miss some SQL management packs, would you please re-download the management pack here and import it:
https://www.microsoft.com/en-hk/download/details.aspx?id=10631
After successful importing, you should see it under reporting workspace:
If you still cannot see it, please check operation manager event logs for more information to help to troubleshoot this issue.
Regards,
Yan Li
Please remember to mark the replies as answers if they help and unmark them if they provide no help. If you have feedback for TechNet Subscriber Support, contact [email protected]

Using ACE for proxy server load balancing

Hello groups,
I wanted to know your experiences of using ACE for proxy server load balancing.
I want to load balance to a pool of proxy servers. Note: load-balancing should be based on the HTTP URL (i can't use source or dest. ip address) so that
a certain domain always gets "cached/forwarded" to the same proxy server. I don't really want to put matching
criteria in the configuration (such as /a* to S1, /b* to S2, /c* to S3,etc..), but have this hash calculated automatically.
Can the ACE compute its own hash based on the number of "online" proxy servers ? ie. when 4 servers are online, distribute domains between 1,2,3,4 evenly.
Should server 4 fail, recalculate hash so that the load of S4 gets distributed across the other 3 evenly. Also load-balancing domains of S1 ,S2 and S3 should not change if S4 fails.....
regards,
Geert

This is done with the following predictor command:
Scimitar1/Admin# conf t
Enter configuration commands, one per line. End with CNTL/Z.
Scimitar1/Admin(config)# serverfarm Proxy
Scimitar1/Admin(config-sfarm-host)# predictor hash ?
address         Configure 'hash address' Predictor algorithms
content         Configure 'hash http content' Predictor algorithms
cookie          Configure 'hash cookie' Predictor algorithms
header          Configure 'hash header' Predictor algorithm
layer4-payload Configure 'hash layer4-payload' Predictor algorithms
url             Configure 'hash url' Predictor algorithm
Scimitar1/Admin(config-sfarm-host)# predictor hash url
It does hash the url and the result takes into account the number of active proxies dynamically.
This command has been designed for this kind of scenario that you describe.
Gilles.

We were using SP3 for iplanet server. Now we want to use SP4.

We were using SP3 for iplanet server. Now we want to use SP4.
When we deploy the EAR on SP4(thru IASDEPLOY), its giving Null pointer
error but at the end it says deployment complete. Also there are no proper
entries in the registry.
If we deploy the same EAR on SP3, then everything is fine.
In SP4, we are not getting even the EAR folder in APPS.

What is this application all about.
May be your ear file has some external dependancy, Can you send the logs for this.
Since it is not deployed, the ear folder is not being created for you.
Thanks,
Rakesh.

How to use itunes for windows server 2003

how to install itunes for windows server 2003

Purchased music from the iTUnes store is in a "AAC protected" format. It can only be used in iTUnes. Any music you buy online these days will have some protection on it where you can only use it in there program.
The way around this is to burn the purchased songs to a CD in iTUnes. Then goto edit>preferences>advanced tab>Import sub tab and set your import settings to something like MP3.
Now put the burned CD back in the PC and "Re"import it into iTunes so its imported in a MP3 format so you can use it in any program. Before importing it tho you need to manually add the name of the song, artist album ect ect

Got Display driver via Windows Update for Windows 8.1 and try to use it for Windows Server 2012 R2

Hi Everyone,
the following driver cab is from Windows Update:
https://onedrive.live.com/?cid=5be01620eea95d8c&id=5BE01620EEA95D8C!138&ithint=file,.cab&authkey=!APDi54-R1Ob5IWQ
It includes this display driver:
Intel(R) Q45/Q43 Express Chipset (Microsoft Corporation - WDDM 1.1)
My problem is: I can't install this driver on Windows Server 2012 R2.
I tried the following, nothing worked:
a) pnputil -i -a intel.cab
b) Extract cab, update the device's driver in device manager, select "search for driver software in this location"
c) copy the files in system32/, system32/drivers, syswow64/ from a Windows 8.1 system to a Windows Server 2012 R2 system
Isn't it true that any Windows 8.1 driver should also work for Windows Server 2012 R2 (same os version)?
Thanks for your replies.
PS: I first posted my question here:
http://answers.microsoft.com/en-us/windows/forum/windows8_1-hardware/got-display-driver-via-windows-update-for-windows/31c287c8-ef84-4c81-8530-8c51412376b7

Hi,
Additionally, did you check this article?
http://www.driveridentifier.com/scan/download.php?item_id=90475670&scanid=9B44546E3BB9410D877D9A90D1439AF8&hardware_id=PCI%5CVEN_8086%26DEV_2E12
Regards.
Vivian Wang

Mirroring Disk Drive Question. Using SVM for Disk Mirroring.

Hello,
I am trying to do mirror in solaris 9 using Solaris Volume Manager. I have total 0-7 disks
4 5 6 7
0 1 2 3
Drive 0 and Drive 4 = Boot Drives
Need to Mirror following drives.
Drive 1 and Drive 5 = Need to mirror
Drive 1 was mounted on: /prod1, /prod2, /prod3, /prod4, /prod5.
Drive 5 was mounted on:/prod16-----/prod20
Then i have umounted both drives and then using format command to equalize the parititions.
Then
I have done following steps.
metadb -a -f /dev/dsk/c1t1d0s7
metadb -a -f /dev/dsk/c1t5d0s7
2)
metainit -f d100 1 1 c1t1d0s0
metainit -f d101 1 1 c1t5d0s0
metainit d0 -m d100
metattach d0 d101
3)
# newfs /dev/md/rdsk/d0
newfs: /dev/md/rdsk/d0 last mounted as /prod16
newfs: construct a new file system /dev/md/rdsk/d0: (y/n)? y
4)
# mount -F ufs /dev/md/dsk/d0 /prod16
Now, target 5 is submirror with target 1 mirror. I was wanted to do /prod1 but some reason it showing /prod16. How can i change this to /prod1?
OR
2nd question: do i need to mirror each drive vice verse?
for example:
metainit -f d102 1 1 c1t5d0s0
metainit -f d103 1 1 c1t1d0s0
metainit d1 -m d102
metattach d1 d103
Let me know.
Thanks
Adeel

I do it a little differently, as follows, which I gleaned from http://slacksite.com/solaris/disksuite/disksuite.html
Create state replicas on slices 6 & 7 (any could be used but we usually use 6/7)
metadb -a -f /dev/dsk/c1t0d0s6
metadb -a /dev/dsk/c1t0d0s7
metadb -a -f /dev/dsk/c1t1d0s6
metadb -a /dev/dsk/c1t1d0s7
Initialize submirrors for root slice 0 on both drives, and create one-way mirror between metadevice d0 & first sub-mirror
metainit -f d10 1 1 c1t1d0s0
metainit -f d20 1 1 c1t1d0s0
metainit d0 -m d10
update root entry in /etc/vfstab
metaroot d0
Initialize submirrors for swap slice on both drives, and create one-way mirror between metadevice d1 & first sub-mirror
metainit -f d11 1 1 c1t0d0s1
metainit -f d21 1 1 c1t1d0s1
metainit d1 -m d11
Initialize submirrors for /var slice5 on both drives, and create one-way mirror between metadevice d5 & first sub-mirror.
metainit -f d15 1 1 c1t0d0s5
metainit -f d20 1 1 c1t1d0s5
metainit d5 -m d15
Edit /etc/vfstab
add these lines to /etc/vfstab
/dev/md/dsk/d1 - - swap - no -
/dev/md/dsk/d5 /dev/md/rdsk/d5 /var ufs 1 no logging
REBOOT server
Attach second half of mirrors to allow two drives to synchronize
metattach d0 d20
metattach d1 d21
metattach d2 d25
I hope this helps.
Stephanie

Linux guy wants to install solaris 10 via nfs using centos as nfs server

well in linux when installing this way I simply copy the dvd install image to an nfs share (or do mount -o loop "isoimage" /nfsmountdir), copy the boot.iso so a cdrom and do a "linux askmethod" during install and then specify the nfs server and dir.
I want to learn sun and want to start by really understanding the install and how to set up slices etc. I would really like to do this using nfs using my centos box as the server as this method at least when installing linux is much mush faster.
so can I do this and if so what are the commands. I did see some documentation but it was for installing from a sun nfs server. but I need to install from the centos as the server. I already have the iso's for the 5 cdroms as well as the dvd image. if possible I would obviously like to use the dvd image.
thanks and remember I am a sun newbie (just bought my first solaris book this week so the more dummied down answer would be the best one for me). if it can be done could you give me the exact process.
thanks a million (and one).

The Sun network installer scripts only work on Solaris. So there's no instructions from Sun for configuring the daemons on Linux necessary to do the configuration.
There are some guides on the net, but I don't know of one that tells the whole story.
You might consider installing Solaris in a VM on the linux box, then configuring jumpstart on that. You could then see how the daemons on it are configured and replicate that configuration on the Linux machine.
Darren

SS2K_SYSLOGINS ORA-01401 using WB for SQL server 2000

Hi there,
I've read some threads on this issue on this forum but no solution to be found.
I noticed that the NAME field on the table SS2K_SYSLOGINS has been declared as varchar2(30) and is reading the SYSLOGINS views column NAME ( as declared sysname 128 ) on SQL server 2000.
This view (based on tabel sysxtypes) is not only containing SQL-logins but also domain users and domain groups ( like "domainxxx.com\SL-DAFEHV-DB-TorqueSupervisor-Admin"
These domain name sometimes are far over 30 characters in length !!!
I download the Migration Workbench ( 10.1.0.4.0 ) and some pluging today ( from http://www.oracle.com/technology/software/tech/migration/workbench/index.html )and I'm running WB 10 and Ora 9.2 both on the same server.
How to solve this problem.
Please help me out.
Guus

Guus,
[It was a new bug, I searched the bug database but could not find something relevant]
We will migrate what we can automate, so if there is more we can automate in future send in the details. Can you send in the database as a testcase?
I had to alter the SS2K_SYSINDEXES as well and had to set the columns FIRST, ROOT, and FIRTSIAM to allow 'null' !!!That is not logged either, which surprises me.
There was an assessment tool to give you an idea of the complexity of the migration that was used internally.
>
Further more I encoutered some warning ( i will not list them all )
A) Within SQL server there are other pre-reserved words as within Oracle.I am not clear what you mean, is the parser failing on not handled reserved words like for example XML features?
B) It cannot handle hops to other databases within/on the same server ( almost the same as using other schema's within Oracle )Consolidation is one of the proposed features of the next release.
C) It cannot deal with the different authentication setup within SQL server 2000 ( databaselink.database.owner.objectname )Will note for future reference.
C2 ) Is it possible to capture related objects from different databases ( ora schema's ) when encoutering them during capture ( the master database has been queried during the capturing as well. . . ) ?You just choose which databases you want to capture the workbench does not work out what parts of database b are called by database a. It was hoped there would be better tools for reorganising schemas when you got to oracle i.e. it was hoped it was out of our scope.
D) It cannot handle;
temptablesTemptables in stored procedures are mapped to oracle temporary tables, whos structure is permanent but the data can be temporary: for example tied to the session. Unhandled temptables in particular situations are a bug.
system procedures like sp_executesql / xp_cmdshell / xp_smtp_send_mail / sp_oacreateWhile the functionality exists in oracle emulating xp_ and sp_ functions has not been done.
function such as NEWID()
user difined functionsI will note this for further reference.
calls to the filesystem ( checking / writing to / reading from / deleting files )While the functionality exists in oracle emulating these functions has not been done.
commandline call ( using xp_cmdshell )
owner prefixes ( schema call as used by Oracle )I think this is done, if it is not done in some places it is a bug.
N' parameter prefixes
and so on , and so on
Think I better skip trying "Migration Workbench" and look for an other way to handle a migration from SQL server 2000 to Oracle 92.We did provide a service to do this for a fee I am not sure if it is still going. Other tools did not seem substancially better than the workbench.
>
My next chalange is to migrate from Informix 7x to Oarcle 9.2 ( Hmmmmm )The workbench also does this, but it is not a single click automatic operation.
Please tell me [at turloch.otierney at oracle.com] if you find other products that are better. What they do better, oracle can do better next time.
It is probably not a good idea to post this information publically on this Oracle forum.
I apologise that your expectations were not met at this time.
Turloch
Message was edited by:
totierne

Using Aggregates for OraBI Server Queries

Hello!
How to refine data in aggregates tables (created by "create aggregates ..." script) after the data in corresponding database tables was updated?
Thanks

Hi
Aggregates will give a better performance for the BW queries.So you can use aggregates to increase the performance of the inout enabled queries also.
http://help.sap.com/saphelp_nw2004s/helpdata/en/44/70f4bb1ffb591ae10000000a1553f7/content.htm
Please refer note: 1083175.May be it could be helpful.
Regards, Hyma

"This version of Xcode cannot be used with OS X Server"

Ran all the updates on the Mac mini for 10.10.3 and associated items. That included Xcode 6.3 (from the App Store). Started Server.app and it asked to choose a new version of Xcode. Did so and it gives the error in the heading.
Never seen this happen before. Stuffs up any chance of using testing bots. Any ideas on how to fix it?

I found it started working if I left it alone for a while. After being contacted by an Apple engineer on Twitter it seems that after everything is updated it takes a while for it to run all of the initialisations. So the approach seems to be:
1) Update OS X, Server.app and Xcode
2) Reboot, start up Server.app and leave it alone until Spotlight has stopped grinding away
3) Start up Xcode and give it a few minutes while it runs all the new initialisation processing
4) Select the Xcode item in Server.app and attach the new version of Xcode
It does seem to get there eventually but isn't helped by the worryingly incorrect error message.

Unable to use PerfMon for Remote Server

I have a Windows Server 2008 R2, which I am running PerfMon. When I try to connect to a remote Windows 2008 server, I receive: Unable to connect to the remote computer with the following error: The Parameter is incorrect.
I can, however, connect to this server with other snap-ins, such as Services and Users and Groups. Furthermore, I can connect to the server using PerfMon from my Windows 7 client.
Any I deas why PerfMon won't work from my R2?
Thanks,
Matt

Hi,
Does it work the other way around? Can you connect form the 2k8 to the 2K8 R2 server?
Best Regards,
Spas Kaloferov
MCITP: SA7 | EA7 | VA7 | EDA7 |DBA10 | DBD10 | BID10 | EMA14 | SPA14
NetShell Services & Solutions | “Design the future with simplicity and elegance”
www:
www.spaskaloferov.com
| www:
www.netshell-solutions.com

Mac OS X Server 4.1, Xcode 6.3.1 "This version of Xcode cannot be used with this server"

I'm utterly confused.
The documentation for Mac OS X Server (from https://help.apple.com/serverapp/mac/4.0/#/apdA154F061-7CE4-4A58-843D-DC2CE3A1AE 8C ) shows that Xcode 6 or later (my emphasis). I have installed Mac OS X 10.10.3, Mac OS X Server 4.1, Xcode 6.3.1. I have no apps in the App Store's "Update" tab that need to be updated (just now double-checked). I clicked to the Xcode tab under "Services" in OS X Server, clicked the "Choose Xcode…" button, selected the version of Xcode from the Applications folder on the root HDD, and got the error message "This version of Xcode cannot be used with OS X Server."
So .... now what?

Well, for some reason it just started working. I was busy trying to fix another issue when I noticed that the Xcode service was running. I would still like to know what happened in case I have a similar problem with the next OS/Server upgrade, but for now it's at least running.

Using F4 for open dataset

HI ,
I want to use open data set for write file to server and my question is how i can use
F4 for the server files ?
Regards
Joy

Hi,
You can tru using the below sample code for the required functionality,
data l_path       TYPE dxlpath .
PARAMETERS:     p_fname    LIKE rlgrap-filename .
*-- F4 functionality for filename on Application Server
CALL FUNCTION '/SAPDMC/LSM_F4_SERVER_FILE'
    EXPORTING
      directory        = '/usr/sap/input'      "directory created for the required functionality
      filemask         = ''
    IMPORTING
      serverfile       = l_path
    EXCEPTIONS
      canceled_by_user = 1
      OTHERS           = 2.
IF sy-subrc <> 0.
    MESSAGE ID sy-msgid TYPE sy-msgty NUMBER sy-msgno
            WITH sy-msgv1 sy-msgv2 sy-msgv3 sy-msgv4.
ELSE.
    p_fname = l_path.
ENDIF.
Hope it helps
Regards
Mansi
Edited by: MANSI ASNANI on Aug 31, 2009 6:03 AM

Solaris 10 cannot mirror using SVM for SFV440 server

Similar Messages

Maybe you are looking for