Solaris 10 x86 & 2 x NIC. Can some1 pls have a look if i do all correctly?
i have a server with two NICs and Solaris 10 x86 installed.
i want to use NIC1 with ADSL router (10.0.0.x) and NIC2 with switch (192.168.16.x). i also want to setup a DHCP server for LAN machines (NIC2) and DNS server.
can someone pls confirm/correct my thoughts/steps in configuring two interfaces?
1. during install i had to chose a default route for both interfaces. for NIC1 it was easy - i just entered the ADSL router IP which was 10.0.0.1.
however, i have a difficulty with NIC2. what default route if at all should i use here?
2. my understanding is that after configuring two interfaces they should act as a bridge so that i could setup a DNS server using my LAN machine addresses (192.168.16.x) and traffic coming from outside the office will be converted properly to reach LAN machines (mail, web servers, etc). is that correct or will i need to setup and configure 2 DNS servers for each NIC respectively?
3. DHCP server. any guidance here in terms of two NICs machine?
many thanks
Alex
i have a server with two NICs and Solaris 10 x86
installed.
i want to use NIC1 with ADSL router (10.0.0.x) and
NIC2 with switch (192.168.16.x). i also want to setup
a DHCP server for LAN machines (NIC2) and DNS
server.
can someone pls confirm/correct my thoughts/steps in
configuring two interfaces?
1. during install i had to chose a default route for
both interfaces. for NIC1 it was easy - i just
entered the ADSL router IP which was 10.0.0.1.
however, i have a difficulty with NIC2. what default
route if at all should i use here?You don't choose a default route for an interface, you choose a default route for a system. It isn't very useful to have multiple default routes for one machine. You will presumably want your default route to point to the internet-facing router.
2. my understanding is that after configuring two
interfaces they should act as a bridgeNo. You can use 'routeadm' on recent releases to configure routing. Otherwise, you need correct routing tables and make sure IP forwarding is enabled.
so that i
could setup a DNS server using my LAN machine
addresses (192.168.16.x) and traffic coming from
outside the office will be converted properly to
reach LAN machines (mail, web servers, etc). is that
correct or will i need to setup and configure 2 DNS
servers for each NIC respectively?Unless your ADSL router understands the routes behind the solaris machine (it almost certainly doesn't), it will never send traffic there. Instead, you would have to run a NAT setup on the machine. ipfilter/ipnat can be used to do that.
3. DHCP server. any guidance here in terms of two
NICs machine?Should be no issues. Just create a scope for the 192.x subnet. If you're using the Solaris DHCP server, you can create a file which prevents it from listening on the other interface, but that's not required.
Darren
Similar Messages
-
Can some one have a look at this php script?
Ok! hear's the script! It work's fine! but with one problem.
when I get the email it look's like this>
Base Color: NaturalTread Color: Black
What I want the email to look like is>
Base Color: Natural
Tread Color: Black
ie i don't want all the "var's" on on line!
Hear's my php code>
Can someone have a look to give me some poniters?I too am learnig. And just found this>
<?php
$sendTo = "******@hotmail.com";
$subject = "Combo Test Two";
$headers = "From: " . $_POST["name"];
$headers .= "<" . $_POST["email"] . ">\r\n";
$headers .= "Reply-To: " . $_POST["email"] . "\r\n";
$headers .= "Return-Path: " . $_POST["email"];
$message .= $_POST["baseColor"] . "\r\n";
$message .= $_POST["treadColor"] . "\r\n";
mail($sendTo, $subject, $message, $headers);
?>
u need to put Line-Feed & Carridge Return:
\r\n
And good luck to you! Thanks for the help my friend! -
Hey guys, I've been trying to save my mac from this constant lag for the past few days to no avail. I've been reading the forums and trying to figure this out myself but I haven't been able to reach a solution so here I am. I've done a clean reinstall. I've run disk permissions and repaired the disk. I've reset PRAM. I don't have FileVault running. I am constantly getting rainbow wheel, even as I'm typing this question out. Applications freeze in their own windows, for example, Chrome will freeze but I will still be able to move over to another application like safari and use safari. It's practically impossible to run any kind media because it stutters constantly. Any and all help is welcome, thanks in advance.
Problem description:
Mid 2012 13” Macbook Pro slowed to a crawl after update to Yosemite. I currently have 10.10.1 running. I have tried a clean install, I’ve resetted PRAM, I’ve run disk permission verification and repair. None have helped. I constantly get rainbow wheel and all sorts of media stutters.
Below are my EtreCheck results. Any and all help is welcome, thanks in advance guys.
EtreCheck version: 2.1.5 (108)
Report generated December 19, 2014 at 3:38:07 PM GMT+2
Click the [Support] links for help with non-Apple products.
Click the [Details] links for more information about that line.
Click the [Adware] links for help removing adware.
Hardware Information: ℹ️
MacBook Pro Intel Core i7, 15" (Mid 2012)
MacBook Pro - model: MacBookPro9,2
1 2.5 GHz Intel Core i5 CPU: 2-core
4 GB RAM Upgradeable
BANK 0/DIMM0
2 GB DDR3 1600 MHz ok
BANK 1/DIMM0
2 GB DDR3 1600 MHz ok
Bluetooth: Good - Handoff/Airdrop2 supported
Wireless: en1: 802.11 a/b/g/n
Video Information: ℹ️
Intel HD Graphics 4000
Color LCD 1280 x 800
System Software: ℹ️
OS X 10.10.1 (14B25) - Uptime: 0:21:9
Disk Information: ℹ️
APPLE HDD TOSHIBA MK5065GSXF disk0 : (500.11 GB)
EFI (disk0s1) <not mounted> : 210 MB
Recovery HD (disk0s3) <not mounted> [Recovery]: 650 MB
SamiEfes HD (disk1) / : 498.88 GB (402.53 GB free)
Core Storage: disk0s2 499.25 GB Online
MATSHITADVD-R UJ-8A8
USB Information: ℹ️
Apple Inc. FaceTime HD Camera (Built-in)
Apple Computer, Inc. IR Receiver
Apple Inc. BRCM20702 Hub
Apple Inc. Bluetooth USB Host Controller
Apple Inc. Apple Internal Keyboard / Trackpad
Thunderbolt Information: ℹ️
Apple Inc. thunderbolt_bus
Gatekeeper: ℹ️
Mac App Store and identified developers
Launch Daemons: ℹ️
[loaded] com.adobe.fpsaud.plist [Support]
User Launch Agents: ℹ️
[loaded] com.google.keystone.agent.plist [Support]
User Login Items: ℹ️
None
Internet Plug-ins: ℹ️
FlashPlayer-10.6: Version: 16.0.0.235 - SDK 10.6 [Support]
Flash Player: Version: 16.0.0.235 - SDK 10.6 [Support]
QuickTime Plugin: Version: 7.7.3
Default Browser: Version: 600 - SDK 10.10
3rd Party Preference Panes: ℹ️
Flash Player [Support]
Time Machine: ℹ️
Auto backup: YES
Volumes being backed up:
SamiEfes HD: Disk size: 498.88 GB Disk used: 96.35 GB
Destinations:
BACKUP [Local]
Total size: 500.10 GB
Total number of backups: 8
Oldest backup: 2014-12-17 03:32:23 +0000
Last backup: 2014-12-18 23:14:04 +0000
Size of backup disk: Adequate
Backup size 500.10 GB > (Disk used 96.35 GB X 3)
Top Processes by CPU: ℹ️
4% Google Chrome
2% WindowServer
0% AppleSpell
0% opendirectoryd
Top Processes by Memory: ℹ️
309 MB Google Chrome Helper
172 MB spindump
163 MB Google Chrome
52 MB mds_stores
52 MB WindowServer
Virtual Memory Information: ℹ️
1.19 GB Free RAM
1.80 GB Active RAM
605 MB Inactive RAM
698 MB Wired RAM
1.20 GB Page-ins
0 B Page-outs
Diagnostics Information: ℹ️
Dec 19, 2014, 03:18:52 PM Self test - passed
MacBook Pro, OS X Yosemite (10.10.1)
It's been a few days since my last post, i've tried uninstalling chrome and adobe flash but my mac is the same. My problems have actually grown. Now my mac is heating up even when the lid is down and the computer is sleeping. The battery has also begun to drain very quickly. Any suggestions? solutions? Below is my current etrecheck result, the one above was when this first started.
EtreCheck version: 2.1.5 (108)
Report generated December 21, 2014 at 10:19:28 PM GMT+2
Click the [Support] links for help with non-Apple products.
Click the [Details] links for more information about that line.
Click the [Adware] links for help removing adware.
Hardware Information: ℹ️
MacBook Pro Intel Core i7, 15" (Mid 2012)
MacBook Pro - model: MacBookPro9,2
1 2.5 GHz Intel Core i5 CPU: 2-core
4 GB RAM Upgradeable
BANK 0/DIMM0
2 GB DDR3 1600 MHz ok
BANK 1/DIMM0
2 GB DDR3 1600 MHz ok
Bluetooth: Good - Handoff/Airdrop2 supported
Wireless: en1: 802.11 a/b/g/n
Video Information: ℹ️
Intel HD Graphics 4000
Color LCD 1280 x 800
System Software: ℹ️
OS X 10.10.1 (14B25) - Uptime: 0:31:36
Disk Information: ℹ️
APPLE HDD TOSHIBA MK5065GSXF disk0 : (500.11 GB)
EFI (disk0s1) <not mounted> : 210 MB
Recovery HD (disk0s3) <not mounted> [Recovery]: 650 MB
SamiEfes HD (disk1) / : 498.88 GB (422.36 GB free)
Core Storage: disk0s2 499.25 GB Online
MATSHITADVD-R UJ-8A8
USB Information: ℹ️
Apple Inc. iPhone
Apple Inc. Apple Internal Keyboard / Trackpad
Apple Computer, Inc. IR Receiver
Apple Inc. BRCM20702 Hub
Apple Inc. Bluetooth USB Host Controller
Apple Inc. FaceTime HD Camera (Built-in)
Thunderbolt Information: ℹ️
Apple Inc. thunderbolt_bus
Gatekeeper: ℹ️
Mac App Store and identified developers
User Launch Agents: ℹ️
[loaded] com.google.keystone.agent.plist [Support]
User Login Items: ℹ️
None
Internet Plug-ins: ℹ️
Default Browser: Version: 600 - SDK 10.10
QuickTime Plugin: Version: 7.7.3
3rd Party Preference Panes: ℹ️
None
Time Machine: ℹ️
Auto backup: YES
Volumes being backed up:
SamiEfes HD: Disk size: 498.88 GB Disk used: 76.52 GB
Destinations:
BACKUP [Local]
Total size: 500.10 GB
Total number of backups: 6
Oldest backup: 2014-12-17 03:32:23 +0000
Last backup: 2014-12-19 21:11:44 +0000
Size of backup disk: Adequate
Backup size 500.10 GB > (Disk used 76.52 GB X 3)
Top Processes by CPU: ℹ️
4% WindowServer
0% helpd
0% AppleSpell
0% launchd
0% coreduetd
Top Processes by Memory: ℹ️
295 MB com.apple.WebKit.WebContent
159 MB Safari
73 MB mds_stores
60 MB WindowServer
43 MB com.apple.WebKit.Networking
Virtual Memory Information: ℹ️
1.49 GB Free RAM
1.80 GB Active RAM
343 MB Inactive RAM
664 MB Wired RAM
812 MB Page-ins
0 B Page-outs
Diagnostics Information: ℹ️
Dec 21, 2014, 09:48:26 PM Self test - passed
Dec 20, 2014, 01:03:45 AM /Library/Logs/DiagnosticReports/Kernel_2014-12-20-010345_[redacted].panic [Details]This is what I got when I ran Linc's code on terminal:
Start time: 09:30:23 12/25/14
Model Identifier: MacBookPro9,2
System Version: OS X 10.10.1 (14B25)
Kernel Version: Darwin 14.0.0
Time since boot: 30 minutes
Diagnostic reports
2014-12-17 mds_stores crash x2
2014-12-20 Kernel panic
2014-12-23 fontd crash x7
Shutdowns
Dec 20 15:30:57 cause: -60
Dec 21 21:51:06 cause: -60
Dec 22 15:00:42 cause: -60
Dec 22 21:28:26 cause: -60
Dec 23 01:14:12 cause: -60
Dec 23 13:20:50 cause: -60
Dec 23 13:34:25 cause: -60
Log
Dec 23 16:21:35 process WindowServer[129] caught causing excessive wakeups. EXC_RESOURCE supressed due to audio playback
Dec 23 18:27:25 PM notification timeout (pid 67, loginwindow)
Dec 23 18:27:25 PM notification timeout (pid 67, loginwindow)
Dec 23 18:27:25 PM notification timeout (pid 67, loginwindow)
Dec 23 20:21:37 pci pause: SDXC
Dec 23 21:43:38 PM notification timeout (pid 42, coreduetd)
Dec 23 23:32:25 pci pause: SDXC
Dec 23 23:48:42 pci pause: SDXC
Dec 23 23:51:27 SerialATAPI device reconfiguration did not complete successfully. (failedCommandInfo = 0x1)
Dec 24 00:01:15 com.apple.xpc.launchd.domain.pid.BKAgentService.633: Path not allowed in target domain: type = pid, path = /Library/Frameworks/iTunesLibrary.framework/Versions/A/XPCServices/com.apple.iT unesLibraryService.xpc error = 147: The specified service did not ship in the requestor's bundle, origin = /System/Library/PrivateFrameworks/BookKit.framework/Versions/A/XPCServices/com. apple.BKAgentService.xpc
Dec 24 00:01:15 com.apple.xpc.launchd.domain.pid.BKAgentService.633: Path not allowed in target domain: type = pid, path = /Library/Frameworks/iTunesLibrary.framework/Versions/A/XPCServices/com.apple.iT unesLibraryService.xpc error = 147: The specified service did not ship in the requestor's bundle, origin = /System/Library/PrivateFrameworks/BookKit.framework/Versions/A/XPCServices/com. apple.BKAgentService.xpc
Dec 24 00:01:44 com.apple.xpc.launchd.domain.pid.MediaLibraryService.642: Path not allowed in target domain: type = pid, path = /Library/Frameworks/iTunesLibrary.framework/Versions/A/XPCServices/com.apple.iT unesLibraryService.xpc error = 147: The specified service did not ship in the requestor's bundle, origin = /System/Library/Frameworks/MediaLibrary.framework/Versions/A/XPCServices/com.ap ple.MediaLibraryService.xpc
Dec 24 00:01:44 com.apple.xpc.launchd.domain.pid.MediaLibraryService.642: Path not allowed in target domain: type = pid, path = /Library/Frameworks/iTunesLibrary.framework/Versions/A/XPCServices/com.apple.iT unesLibraryService.xpc error = 147: The specified service did not ship in the requestor's bundle, origin = /System/Library/Frameworks/MediaLibrary.framework/Versions/A/XPCServices/com.ap ple.MediaLibraryService.xpc
Dec 24 01:27:21 PM notification timeout (pid 27, powerd)
Dec 24 01:29:24 pci pause: SDXC
Dec 24 18:23:40 process com.apple.WebKit[285] caught causing excessive wakeups. Observed wakeups rate (per sec): 258; Maximum permitted wakeups rate (per sec): 150; Observation period: 300 seconds; Task lifetime number of wakeups: 229247
Dec 24 18:48:20 wl0: Beacon Loss Event, last RSSI[-77]
Dec 24 19:00:24 PM notification timeout (pid 67, loginwindow)
Dec 24 19:00:24 PM notification timeout (pid 67, loginwindow)
Dec 24 19:00:24 PM notification timeout (pid 67, loginwindow)
Dec 24 19:54:42 pci pause: SDXC
Dec 24 23:25:25 PM notification timeout (pid 27, powerd)
Dec 25 02:29:44 pci pause: SDXC
Dec 25 03:01:45 PM notification timeout (pid 152, VDCAssistant)
Dec 25 03:02:15 PM notification timeout (pid 27, powerd)
Agents
com.apple.PTPCamera.45472.UUID
com.google.keystone.user.agent
com.apple.AirPortBaseStationAgent
Bundles
/Users/USER/Downloads/EtreCheck.app
- com.etresoft.EtreCheck
/Users/USER/Library/Address Book Plug-Ins/SkypeABDialer.bundle
- com.skype.skypeabdialer
/Users/USER/Library/Address Book Plug-Ins/SkypeABSMS.bundle
- com.skype.skypeabsms
/Users/USER/Library/Application Support/Google/Chrome/Default/Web Applications/_crx_aohghmighlieiainnegkcijnfilokake/Default aohghmighlieiainnegkcijnfilokake.app
- com.google.Chrome.app.Default-aohghmighlieiainnegkcijnfilokake-internal
/Users/USER/Library/Application Support/Google/Chrome/Default/Web Applications/_crx_apdfllckaahabafndbhieahigkjlhalf/Default apdfllckaahabafndbhieahigkjlhalf.app
- com.google.Chrome.app.Default-apdfllckaahabafndbhieahigkjlhalf-internal
/Users/USER/Library/Application Support/Google/Chrome/Default/Web Applications/_crx_blpcfgokakmgnkcojhhkbfbldkacnbeo/Default blpcfgokakmgnkcojhhkbfbldkacnbeo.app
- com.google.Chrome.app.Default-blpcfgokakmgnkcojhhkbfbldkacnbeo-internal
/Users/USER/Library/Application Support/Google/Chrome/Default/Web Applications/_crx_coobgpohoikkiipiblmjeljniedjpjpf/Default coobgpohoikkiipiblmjeljniedjpjpf.app
- com.google.Chrome.app.Default-coobgpohoikkiipiblmjeljniedjpjpf-internal
/Users/USER/Library/Google/GoogleSoftwareUpdate/GoogleSoftwareUpdate.bundle
- com.google.Keystone
dylibs
/Users/USER/Library/Application Support/Google/Chrome/WidevineCDM/1.4.6.703/_platform_specific/mac_x64/libwidev inecdm.dylib
Contents of Library/LaunchAgents/com.google.keystone.agent.plist (checksum 3747762641)
<?xml version="1.0" encoding="UTF-8"?>
<!DOCTYPE plist PUBLIC "-//Apple//DTD PLIST 1.0//EN" "http://www.apple.com/DTDs/PropertyList-1.0.dtd">
<plist version="1.0">
<dict>
<key>Label</key>
<string>com.google.keystone.user.agent</string>
<key>LimitLoadToSessionType</key>
<string>Aqua</string>
<key>ProgramArguments</key>
<array>
<string>/Users/USER/Library/Google/GoogleSoftwareUpdate/GoogleSoftwareUpdate.bu ndle/Contents/Resources/GoogleSoftwareUpdateAgent.app/Contents/MacOS/GoogleSoftw areUpdateAgent</string>
<string>-runMode</string>
<string>ifneeded</string>
</array>
<key>RunAtLoad</key>
<true/>
<key>StartInterval</key>
<integer>3523</integer>
<key>StandardErrorPath</key>
<string>/dev/null</string>
<key>StandardOutPath</key>
<string>/dev/null</string>
</dict>
</plist>
User login items
iTunesHelper
- /Applications/iTunes.app/Contents/MacOS/iTunesHelper.app
Restricted files: 53
Lockfiles: 1
Elapsed time (s): 1037 -
Music in N73 can be improved have a look
Guys have a look at the following link and follow what is written
/discussions/board/message?board.id=swupdate&message.id=17988&query.id=203532#M17988Hello PamelaGS,
Thanks for using Apple Support Communities.
Please see the information below for resolving this issue where the cloud icon has an exclamation point inside of it.
Error
This icon may appear if the song file is corrupt or if there was an error uploading the song. Try updating iTunes Match (Store > Update iTunes Match) to resolve this. If updating doesn't resolve the issue, try importing a new copy of the song into your iTunes library.
iTunes Match: Understanding the iCloud Status icons
Take care,
Alex H. -
Can you please have a look on this small script?[SOLVED]
Hello guys,
I am writing a small script which has to do the following:
1. It should run without any interruption. (Therefore while [ 1 ])
2. While working continuously, it should check whether a folder named "check" is available in the folder "/home/arch".
3. If it is the case, it should execute the script /home/arch/shutdownServer1
The bash script I am trying to execute is the following:
#!/bin/bash
while [ 1 ]
do
if [$(ls /home/arch | grep check)="check"]; then
/home/arch/shutdownServer1
fi
done
I tried to execute the code while the folder named "check" was available in the folder "/home/arch" But I got the following error.
/home/arch/myscript: line 5: [check=check]: command not found => This implies that the expression "$(ls /home/arch | grep check)" was evaluated correctly because of check=check. But why does it say "command not found"? Since check=check it should be evaluated as true and execute the script shutdownServer1?
P.S.: myscript is the name of the bash script file.
Guys, please help me.
Thanks in advance
Last edited by Archie_Enthusiasm (2010-11-29 12:20:58)Try one of these
if [ $(ls ~/ | grep check) ]; then
~/shutdownServer1
fi
or
[ $(ls ~/ | grep check) ] && ~/shutdownServer1
Edit: @Allan: thanks for '-d', I completely forgot that
Last edited by igndenok (2010-11-29 11:59:16) -
No /dev/lp? on COMPAQ Proliant ML370 with Solaris 8 x86 10/00
Dear Sir,
I have a problem about the /dev/lp? port in Solaris 8 x86 with COMPAQ Proliant ML370. I have seen in the boot interpreter it has detected a parallel port
device isa/lp@1...., but after I boot -r to start Solaris 8
OS it don't make any /dev/lp? or /devices/isa/lp*... and if
I mknod /dev/lp? myself it cannot print out ( I use cat /etc/hosts >> /dev/lp1, /dev/lp1 major=83 minor=1 ) It say "cannot create". I wonder why this happens, If I install this Solaris 8 x86 on other PC model. It has /dev/lp1 and can print out successfully. I try many ways such as: upgrade latest ROMPAQ BIOS firmware,
install lp driver patch set, install acpi patch. But still don't work. I found that serial ports (asy) which are ACPI is working because I can redirect console to serial port (asy).
Do anyone have the idea to solve or track down this problems. Thanks a lot...Check out the HP Compaq web site and you shuld be able to find the Solaris drivers that are needed. http://h18023.www1.hp.com/support/files/server/us/download/19340.html
-
Solaris 10 x86 Firewire (IEEE 1394) camera frame grabbing
How do you do frame (sequence) grabbing from Firewire (IEEE 1394) camera on Solaris 10 x86? What API can I use?
XIL documentation doesn't seem to mention Firewire cameras specifically. And I tried to compile Linux libdc1394 on Solaris 10 x86, but got errors.
Thank you.Hello Mark,
these forums are user-to-user.
If you work for Caen Engineering, Inc. I would strongly recommend that you contact Sun directly as an OEM.
Unfortunately you didn't mention the particular blog you referring to.
A quick search ("Solaris firewire") on blogs.sun.com returned the following blog entry from January 2006
Firewire in Solaris: The Good, The Bad and The Ugly
Michael -
Agent installation on Solaris 10 x86 64
I'm stuck in the middle of installation, I've tried to perform installation in offline mode, I've reached to the point where I've downloaded successfully the agent software but when I try to do "emcli get_supported_platforms" I don't get the Solaris 10 x86 64 platform.
Hi
can you tell me more about this problem:
1) u download the agent sowfate in offline mode
2) u will get the pop-up to download the package
3) u run the emcli- catalog command and then import it to the oms
4) go to the slef update see the agent bianries - apply them
5) push the agent
In which step are u ? and when are you runing the emcli get_supported_platforms ?
What is the agent install error you are getting -
Create filesystems on Solaris 10 x86
Hi All,
I am not expert in Solaris, I just want to add an external
disk (via San) to a Solaris 10 x86 system.
When I execute #format, have the following :
0) c1t0d0 ....
2) c4t60060160D9E01D009AAB136E0F54DE11d0
/Scsi_uhci/disk@g60060160d9ede11
When I choose number 2, the very disk, I have the following :
Selecting c4t60060160D9E01D009AAB136E0F54DE11d0
[disk formatted]
/dev/dsk/c4t60060160D9E01D009AAB136E0F54DE11d0s2
is part of SVM volme stripped : d7
Please see metaclear.
Then I execute "verify" at the format Promp and got :
Part Tag Flag Cylinder Size
0 Unassigned wm 0 0
1 Unassigned wm 0 0
2 Backup wu 0-17442 133.62Gb
3 Unassigned wm 0 0
4 Unassigned wm 0 0
5 Unassigned wm 0 0
6 Unassigned wm 0 0
7 Unassigned wm 0 0
8 Boot wu 0 7.84Mb
9 Unassigned wm 0 0
My problem is to create 2 partitions, one of 70Gb and the
other one is the rest of the disk, then create filesystems on
them, how to proceed ?
Thanks
BandonHi All,
I am not expert in Solaris, I just want to add an external
disk (via San) to a Solaris 10 x86 system.
When I execute #format, have the following :
0) c1t0d0 ....
2) c4t60060160D9E01D009AAB136E0F54DE11d0
/Scsi_uhci/disk@g60060160d9ede11
When I choose number 2, the very disk, I have the following :
Selecting c4t60060160D9E01D009AAB136E0F54DE11d0
[disk formatted]
/dev/dsk/c4t60060160D9E01D009AAB136E0F54DE11d0s2
is part of SVM volme stripped : d7
Please see metaclear.
Then I execute "verify" at the format Promp and got :
Part Tag Flag Cylinder Size
0 Unassigned wm 0 0
1 Unassigned wm 0 0
2 Backup wu 0-17442 133.62Gb
3 Unassigned wm 0 0
4 Unassigned wm 0 0
5 Unassigned wm 0 0
6 Unassigned wm 0 0
7 Unassigned wm 0 0
8 Boot wu 0 7.84Mb
9 Unassigned wm 0 0
My problem is to create 2 partitions, one of 70Gb and the
other one is the rest of the disk, then create filesystems on
them, how to proceed ?
Thanks
Bandon -
Can someone pls explain me (networking, DNS)
hi guys,
can some1 pls explain me what is hostname in the following record:
mysite.com. IN SOA hostname.mysite.com. admin.mysite.com. (1; 3h; 1h; 1w; 1h)
is it the name of my network interface ?
many thanks
Alexok, it looks like..
now to configure the MX record shall i point it to m0.mysite.com?
the thing is: i actually don't quite understand what is hostname (network interface) and host of my domain. in windows i came from there was a computer name (any name for local network use) , but i never used it in MS Exchange. i used to have an MX record pointing to mail.mysite.com, but in fact the machine's name was M0.
will highly appreciate some insight on this subject.
many thanks
alex -
After installed Solaris 10 X86 I CAN'T SEE GUI
Hi,
I have installed Solaris 10 X86. while installing the software from the CD
I got a nice GUI . After install all 5 CD and reboot I got a choice to boot into Solaris or WIndows, I chose Solaris and wait to loads the GUI but I got only black screen and a monitor message saying the Frequency is low. I got only # prompt .
run search forums about gui problem and no find specific help.
run kdmconfig and change to Xsun, it's not solve the problem.
I CAN'T SEE GUI.
Do i need run any command or install any other program ?
Thanks,
NEED HELP!!!!!Hi ,
try to run #kdmconfig at ur promt , it will ask u to set new gui settings
select ur appropriate vga card , which is being supported ny ur os , n make a logoff , automatically it will drop u on a gui screen to make a login
or u can use #/usr/X11/bin/xorgconfig to define all the new settings from the scratch , i think it should help u out
regards
Kinshuk -
How can i Install Liquid data 1.0 on Solaris 10(x86) Machine
Hi,
I have installed Weblogic 8.1 SP2 on a Solaris 10 x86 Intel Architecture platform. Now I am trying to have BEA Liquid Data for WebLogic 8.1 SP2 also installed on this machine. I couldnot find Liquid Data for WebLogic 8.1 SP2 for Solaris 10, although there seems to be one available for Sun Solaris (8,9,32 bit).
Q1) I understand these are for SPARC and not x86 IA platform is that correct?
When i try to use this above file version to install on Solaris 10 i get the following error.
./liquiddata812_solaris1.bin
Preparing to install...
Extracting the JRE from the installer archive...
Unpacking the JRE...
Extracting the installation resources from the installer archive...
Configuring the installer for this system's environment...
Launching installer...
./liquiddata812_solaris1.bin: /tmp/install.dir.1379/Solaris/resource/jre/bin/java: cannot execute
Q2) Is there a BEA Liquid Data for WebLogic 8.1 SP2 available that can be installed on Solaris (9 or 10) x86 IA.
Thanks
Sandeshhttp://edocs/liquiddata/docs81/install/prep.html#1039271
It is not supported on Solaris running on Intel.
btw - AquaLogic DSP (aka LD8.5) is the current version. It is not supported on Solaris running on Intel, either.
- mike -
Solaris 10 x86 DL-360 How to make additional NICS Show.
Installing Solaris 10 x86 on a DL-360 with 4 NIC's. The server comes normally with 2 built in.
The first was seen fine..
bge0
When I tried to use the 2nd one, bge1, I had to plumb it first.
ifconfig bge1 plumbNo problem...
Now I need to use the 3rd port but the same command is not working.
I would assume that it would be bge2 ??If I understand you correctly, you have two gigabit Ethernet ports as a part of your computer's systemboard, and you have two more Ethernet ports because there are add-in card or cards.
The bge device name is a result of the particular chipset circuitry
and is not a generic term for just any old network port.
It is a name derived from a BroadCom Gigabit Ethernet chipset.
So ... who created the chipsets for the 3rd and 4th network ports?
ipbr is an example from Intel.
le was a common Lowspeed Ethernet (10mbit) circuit in Sun systems in the last century.
hme was a common integrated Highspeed Media Ethernet interface (10/100mbit) on Sun systemboards.
eri is a common Ethernet Rio Interface (10/100) on newer Sun systemboards.
elx is a name associated with 3COM EtherLink chipsets.
dnet is an interface from the DEC21x4x chipsets and could be 10mbit or 10/100mbit adapters per whichever DEC chip was used.
You're going to have to determine what you actually have, confirm you have the appropriate software packages for that hardware, and then you may have a chance to plumb them. -
Can someone share Solaris 10 x86 patch 145028-01?
Hi All,
My sunsolve account does not have priviledge to download Solaris 10 x86 patch 145028-01. Can someone download and share this patch with me?
Regards,
SDSo let's see ...
You want me to spend money in sufficient amounts to have a service sontract that gives me access to patch downloads.
... but you then want it for free?
No! -
Solaris mirroring can some1 explain to ex-Windows guy how to get that done?
i looked through the forum and have seen some advices but am not very comfortable with sending commands i know nothing about.
can someone pls break it down to exact steps needed to mirror a drive in x86 box please? i failed to achieve anything with SVC utility as i don't know what to choose on those so called wizard screens - they are not intuitive for someone coming from windows platform or maybe its just me.
i have two identical 147GB drives in x86 machine. Solaris 10 downloaded and installed on one of them few days ago.
need help please.Hello folks,
In my case the following are output of format command. Do the "format"to identify the disks in your system and replace disks in the steps with the help of that output.
bash-3.00# format
Searching for disks...done
AVAILABLE DISK SELECTIONS:
0. c1t0d0 <SUN146G cyl 14087 alt 2 hd 24 sec 848>
/pci@9,600000/SUNW,qlc@2/fp@0,0/ssd@w5000cca004195269,0
1. c1t1d0 <SUN146G cyl 14087 alt 2 hd 24 sec 848>
/pci@9,600000/SUNW,qlc@2/fp@0,0/ssd@w5000cca00419ab5d,0
Please folllow the below steps for mirroring.
1) Important precaution:
Copy /etc/vfstab and /etc/system
cp -p /etc/system /etc/system.orig
cp -p /etc/vfstab /etc/vfstab.orig
2) Create a small slice of 25 Mbyte (10 Mbyte is also fine) for storing volume databases on the "rootdisk" and label the disk.
Take slice 7
using format command ( Please let me know if you need more explanation)
3) The VTOC (volume table of contents) on the root disk and root mirror must be the same. Copy the VTOC using prtvtoc and fmthard.
# prtvtoc /dev/rdsk/c1t0d0s2 | fmthard -s - /dev/rdsk/c1t1d0s2
5) Create metadatabases on the small slice created on rootdisk:
# metadb -f -a -c3 /dev/dsk/c1t0d0s7
# metadb -a -c3 /dev/dsk/c1t1d0s7
6) Now we can create a mirror for each and every slice in the partition table.
For root or / partition:
# metainit -f d10 1 1 /dev/dsk/c1t0d0s0
# metainit d20 1 1 /dev/dsk/ c1t1d0s0
(create a md d0 and attach one submirror)
# metainit d0 -m d10
(set up system files for root (/) metadevice, that is,
changes to /etc/system and /etc/vfstab)
# metaroot d0
# lockfs -fa (clear improper file locks on all mounted UFS file systems)
7) Naming convention for other metadisks follow. (Note for those who are new to this software: We will not do metaroot and lockfs steps on other file systems.) The submirrors will be named d10, d20, and so on.
In d10, 1 is the submirror number, and 0 is the slice number.
If we have swap on partition/slice 1, we would do this:
# metainit -f d11 1 1 /dev/dsk/c1t0d0s1
# metainit d21 1 1 /dev/dsk/c1t1d0s1
# metainit d1 -m d11
For /var
# metainit -f d12 1 1 /dev/dsk/c1t0d0s3
# metainit d22 1 1 /dev/dsk/c1t1d0s3
# metainit d2 -m d12
8) Repeat for as many file systems you have on your boot disk.
9) Make changes to your /etc/vfstab. The md entry for root will already be updated by the metaroot command.
A sample copy of /etc/vfstab looks like this:
#device device mount FS fsck mount mount
#to mount to fsck point type pass at boot options
fd - /dev/fd fd - no -
/proc - /proc proc - no -
/dev/md/dsk/d1 - - swap - no -
/dev/md/dsk/d0 /dev/md/rdsk/d0 / ufs 1 no -
/dev/md/dsk/d2 /dev/md/rdsk/d2 /var ufs 1 no -
/devices - /devices devfs - no -
ctfs - /system/contract ctfs - no -
objfs - /system/object objfs - no -
swap - /tmp tmpfs - yes -
10) Configure your dump device using dumpadm.
11) Make the following entry in the /etc/system file, in the mdd info section:
set md:mirrored_root_flag=1
12) Execute:
sync; sync; init 6
13) Once the system comes up, attach the other submirror:
# metattach d0 d20
(Note: It's "metattach" and not "metaattach")
# metattach d1 d21
# metattach d1 d22
14) To see whether the FS syncing is done or not, do this:
metastat | grep progress
Once syncing is finished,please reboot the machine once more. Now the disks will be mirrored.
Thanks,
Sal.
Maybe you are looking for
-
Adobe Acrobat Distiller 9 crashes on start
I recently bought a new notebook with Intel Pentium dual-core processor T3400 and Windows Vista Home Premium pre-installed. This weekend, I have been installing some software, including Adobe Acrobat 9 Pro and Adobe Photoshop CS4 Extended. Actually,
-
Literally every single thing that I click on will redirect me to some bull crap website (ie. mackeeper, bullet flix, russian mail order brides). This happened once before but went away after I noticed that my firewall wasn't enabled. But now its back
-
Graphics not extending to edge of mobile screen in preview mode
Not sure if this is a bug or what... in design mode, my Accordion/menu goes the full width of the mobile page, but when I preview it, it doesn't reach the right edge, leaving a gap of open space.
-
How do I work whit windows on mac, like a mac or like a pc?
I installes parallels, and now I`m trying to install windows after write the windows key this asked me how do I want to work windows like a mac or like a pc? Can some one tell me what to do?
-
A3 document format doesn't choose correct format automatically when printing
Situation: - Mac OS X 10.10 - ID CS6 - Bizhub c284 printer - Document format is A3 Problem: When printing, the Print dialogue doesn't choose A3 automatically. In other applications, this work. Is there any way to make Indesign automatically choose A3