[SOLVED] LVM volume not found while booting

I have an error while trying to boot with both Syslinux and GRUB (GRUB was my 1st choice but I got this error so switched to Syslinux). It's BIOS system, my boot is on /dev/sda1 and root is inside LVM on /dev/sda2. It states that device /dev/mapper/TheVG-RootLV can not be found so the problem is with LVM. There is lvm2 hook in mkinitcpio.conf, dolvm in my kernel line... what could I do wrong? I had no problem with this exact setup on my UEFI system and GRUB. Boot partition is loaded even if it's also inside LVM (that was the case when I was trying to run it via GRUB). GPT partition table.
Last edited by smsware (2013-05-25 16:55:48)

This has been an ongoing issue with the Arch Linux LVM2 setup since it was changed to using lvmetad. You did nothing wrong. My home server still sits on an LVM, so what I did was downgraded lvm2 and device-mapper on that machine and have been ignoring the updates until I can find a better solution... though I haven't been looking very hard.
Also, with mkinitcpio, there is no "dolvm" command line parameter. It runs the LVM2 stuff depending on whether or not you have the lvm hook in your mkinicpio.conf (or add it otherwise with the command line). So yu can safely remove that.
The reason that Grub is able to read the /boot partition, but then it can still fail to find the rootfs is because these are two separate things. Grub has its own system to give it LVM compatibility. So it uses its stuff to read that, gets the information it needs, then loads the kernel and initramfs. It then passes the system off, at which point, this process of detecting the LVM and finding the rootfs happens all over again, albiet with the kernel and native linux userspace tools.
My laptop was on LVM2 when this change occurred. It worked for a while, and then just totally borked... well not toally, but it was way inconsistent and super frusturating. So I changed to btrfs. There is a thread about luks and lvm2 not booting, but it is actually just about lvm2, as the luks part of it was just cioncidence. You may want to ahve a look there because there is a slight change you can make in your lvm.conf that might help. It helped in my case, but it only made it slightly less borked, which is why I eventually changed setups.
Edit: I remember the edit having something to do with a filter... or global filter... something about having it not scan floppies and cdroms and whatnot.
Last edited by WonderWoofy (2013-05-23 00:05:31)

Similar Messages

[SOLVED] rEFInd -- Error: Not Found while loading vmlinuz-linux

System Info:
3.14.1-1-ARCH
refind-efi-0.7.8-1
Problem: rEFInd does not boot arch linux.
When booting the machine, rEFInd's gui selection menu presents options for windows or linux.
Upon selecting linux, the following is displayed:
rEFInd - Booting OS
Starting vmlinuz-linux
Using load options 'ro root=UUID=bd6b3352-1b79-4c70-a061-21ff87ff0772 initrd=\boot\initramfs-linux.img'
Invalid loader file!
Error: Not Found while loading vmlinuz-linux
* Hit any key to continue *
Below are the outputs of blkid, lsblk -f, the structure of /boot and cats of /boot/efi/EFI/refind/refind.conf and /boot/refind_linux.conf
blkid
/dev/sda1: UUID="2014-05-01-05-20-54-00" LABEL="ARCH_201405" TYPE="iso9660" PTUUID="1535e446" PTTYPE="dos" PARTUUID="1535e446-01"
/dev/sda2: SEC_TYPE="msdos" LABEL="ARCHISO_EFI" UUID="96ED-5DA9" TYPE="vfat" PARTUUID="1535e446-02"
/dev/sdb1: LABEL="Recovery" UUID="E63202B832028E2D" TYPE="ntfs" PARTLABEL="Basic data partition" PARTUUID="e3729f62-9c32-4ac9-a9dd-56a9c073e7e5"
/dev/sdb2: UUID="9C03-552D" TYPE="vfat" PARTLABEL="EFI system partition" PARTUUID="9bcdb083-82e9-49e6-b03d-fd376585d633"
/dev/sdb4: UUID="B2161962161928BD" TYPE="ntfs" PARTLABEL="Basic data partition" PARTUUID="6de10de9-3322-486c-8108-bf14f5a7bcb6"
/dev/sdb5: UUID="bd6b3352-1b79-4c70-a061-21ff87ff0772" TYPE="ext4" PARTLABEL="root" PARTUUID="699115b1-1413-42b3-9fd7-a80a8a51b6fa"
/dev/sdb6: UUID="e71e6a25-913a-4932-9fc9-81942a5dab2e" TYPE="ext4" PARTLABEL="home" PARTUUID="1fc33e24-4c26-459c-a80a-9440e1f4e683"
/dev/loop0: TYPE="squashfs"
/dev/loop1: UUID="f07bfb26-3377-487a-a022-efd840614a0d" TYPE="ext4"
/dev/loop2: UUID="f07bfb26-3377-487a-a022-efd840614a0d" TYPE="ext4"
/dev/mapper/arch_root-image: UUID="f07bfb26-3377-487a-a022-efd840614a0d" TYPE="ext4"
/dev/sdb3: PARTLABEL="Microsoft reserved partition" PARTUUID="fa94c812-e1ff-4603-ba97-be7f155f12c8"
lsblk -f
NAME FSTYPE LABEL UUID MOUNTPOINT
sdb
├─sdb1
├─sdb2 /boot/efi
├─sdb3
├─sdb4
├─sdb5 /
└─sdb6 /home
sdc
├─sdc1
└─sdc2
loop0
loop1
└─arch_root-image /etc/resolv.conf
loop2
└─arch_root-image /etc/resolv.conf
Structure of /boot
*note: /boot is really the original microsoft efi system partition (in my case, /dev/sda2) that I mounted to /boot/efi and whose structure is shown below:
/boot
├── efi
│ ├── EFI
│ │ ├── Boot
│ │ │ └── bootx64.efi
│ │ ├── Microsoft
│ │ │ └── Boot
│ │ │ ├── BCD
│ │ │ ├── BCD.LOG
│ │ │ ├── BCD.LOG1
│ │ │ ├── BCD.LOG2
│ │ │ ├── bg-BG
│ │ │ │ ├── bootmgfw.efi.mui
│ │ │ │ └── bootmgr.efi.mui
│ │ │ ├── bootmgfw.efi
│ │ │ ├── bootmgr.efi
│ │ │ ├── BOOTSTAT.DAT
│ │ │ ├── boot.stl
│ │ │ ├── en-US
│ │ │ │ ├── bootmgfw.efi.mui
│ │ │ │ ├── bootmgr.efi.mui
│ │ │ │ └── memtest.efi.mui
│ │ │ ├── Fonts
│ │ │ │ ├── {{FONTS REMOVED FOR BREVITY}}
│ │ │ ├── Resources
│ │ │ │ ├── bootres.dll
│ │ │ │ └── en-US
│ │ │ │ └── bootres.dll.mui
│ │ ├── refind
│ │ │ ├── drivers_x64
│ │ │ │ └── ext4_x64.efi
│ │ │ ├── icons
│ │ │ │ ├── {{ICONS REMOVED FOR BREVITY}}
│ │ │ ├── keys
│ │ │ │ ├── altlinux.cer
│ │ │ │ ├── canonical-uefi-ca.der
│ │ │ │ ├── fedora-ca.cer
│ │ │ │ ├── openSUSE-UEFI-CA-Certificate.cer
│ │ │ │ ├── refind.cer
│ │ │ │ └── SLES-UEFI-CA-Certificate.cer
│ │ │ ├── refind.conf <=================== http://ix.io/cFy
│ │ │ └── refind_x64.efi
│ │ └── tools
│ ├── initramfs-linux-fallback.img
│ ├── initramfs-linux.img
│ └── vmlinuz-linux
└── refind_linux.conf <===================== http://ix.io/cFw
49 directories, 190 files
Excerpt of /boot/efi/EFI/refind/refind.conf
(full file available here: http://ix.io/cFy)
menuentry Linux {
icon EFI/refind/icons/os_arch.icns
volume "EFI system partition"
loader /boot/vmlinuz-linux
initrd /boot/initramfs-linux.img
options "ro root=UUID=bd6b3352-1b79-4c70-a061-21ff87ff0772"
cat /boot/refind_linux.conf
"Boot with standard options" "ro root=UUID=bd6b3352-1b79-4c70-a061-21ff87ff0772 "
"Boot to single-user mode" "ro root=UUID=bd6b3352-1b79-4c70-a061-21ff87ff0772 single"
"Boot with minimal options" "ro root=UUID=bd6b3352-1b79-4c70-a061-21ff87ff0772"
Last edited by dk0r (2014-05-28 01:36:16)

A couple of things that are important:
refind_linux.conf should be in the same directory as vmlinuz-linux and the initrd so it should be in /boot/ since that is where your kernel is.
In your refind.conf stanza you have the line volume "EFI system partition" which tells rEFInd that the loader is in that partition whereas the kernel and initrd files seem to be in /boot/ which is not the EFI System Partition. Hence the volume line needs to specify the filesystem where /boot is which in your case appears to be /dev/sdb5 so the volume line in that case should be volume "root" since root is the filesystem label for sdb5? Note that if you update to rEFInd version 0.8.0 or later then you can use the partuuid value to specify the volume but in the version you are using that token for the volume was not yet implemented.
In the stanza you quoted there was no terminating } but maybe you just didn't copy it to your post.
Making these changes may let the system boot to the arch kernel.
Last edited by mcloaked (2014-05-27 20:21:16)

[Solved] grub2: file not found but booting fine

I just ran grub-mkconfig to update my grub.cfg because I installed E4rat. But now I have a problem: Every entry in grub2 can be booted and E4rat really boosted my boot process so actually everything is fine. But while grub2 is loading it says something like:
Grub 2 is loading...
Welcome to Grub 2!
error: file not found.
error: file not found.
error: file not found.
Now grub shows up and everything is as it should be. When I select Arch it again says "error: file not found." three times and continues with a normal boot process. So basically it's nothing that would brake my system but something seems not right and that's just a huge annoyance.
Here's my grub.cfg just in case:
# DO NOT EDIT THIS FILE
# It is automatically generated by grub-mkconfig using templates
# from /etc/grub.d and settings from /etc/default/grub
### BEGIN /etc/grub.d/00_header ###
insmod part_gpt
insmod part_msdos
if [ -s $prefix/grubenv ]; then
load_env
fi
set default="0"
if [ x"${feature_menuentry_id}" = xy ]; then
menuentry_id_option="--id"
else
menuentry_id_option=""
fi
export menuentry_id_option
if [ "${prev_saved_entry}" ]; then
set saved_entry="${prev_saved_entry}"
save_env saved_entry
set prev_saved_entry=
save_env prev_saved_entry
set boot_once=true
fi
function savedefault {
if [ -z "${boot_once}" ]; then
saved_entry="${chosen}"
save_env saved_entry
fi
function load_video {
if [ x$feature_all_video_module = xy ]; then
insmod all_video
else
insmod efi_gop
insmod efi_uga
insmod ieee1275_fb
insmod vbe
insmod vga
insmod video_bochs
insmod video_cirrus
fi
set menu_color_normal=light-blue/black
set menu_color_highlight=light-cyan/blue
if [ x$feature_default_font_path = xy ] ; then
font=unicode
else
insmod part_msdos
insmod ext2
set root='hd0,msdos5'
if [ x$feature_platform_search_hint = xy ]; then
search --no-floppy --fs-uuid --set=root --hint-bios=hd0,msdos5 --hint-efi=hd0,msdos5 --hint-baremetal=ahci0,msdos5 --hint='hd0,msdos5' f7960d1a-77ab-4230-ab43-ff931f0b2175
else
search --no-floppy --fs-uuid --set=root f7960d1a-77ab-4230-ab43-ff931f0b2175
fi
font="/usr/share/grub/unicode.pf2"
fi
if loadfont $font ; then
set gfxmode=1440x900x32
load_video
insmod gfxterm
set locale_dir=$prefix/locale
set lang=en_GB
insmod gettext
fi
terminal_input console
terminal_output gfxterm
insmod part_msdos
insmod ext2
set root='hd0,msdos5'
if [ x$feature_platform_search_hint = xy ]; then
search --no-floppy --fs-uuid --set=root --hint-bios=hd0,msdos5 --hint-efi=hd0,msdos5 --hint-baremetal=ahci0,msdos5 --hint='hd0,msdos5' f7960d1a-77ab-4230-ab43-ff931f0b2175
else
search --no-floppy --fs-uuid --set=root f7960d1a-77ab-4230-ab43-ff931f0b2175
fi
insmod png
background_image -m stretch /boot/grub/archlinux.png
set timeout=5
### END /etc/grub.d/00_header ###
### BEGIN /etc/grub.d/10_linux ###
menuentry 'Arch Linux GNU/Linux, with Linux core repo kernel' --class arch --class gnu-linux --class gnu --class os $menuentry_id_option 'gnulinux-core repo kernel-true-f7960d1a-77ab-4230-ab43-ff931f0b2175' {
load_video
set gfxpayload=keep
insmod gzio
insmod part_msdos
insmod ext2
set root='hd0,msdos5'
if [ x$feature_platform_search_hint = xy ]; then
search --no-floppy --fs-uuid --set=root --hint-bios=hd0,msdos5 --hint-efi=hd0,msdos5 --hint-baremetal=ahci0,msdos5 --hint='hd0,msdos5' f7960d1a-77ab-4230-ab43-ff931f0b2175
else
search --no-floppy --fs-uuid --set=root f7960d1a-77ab-4230-ab43-ff931f0b2175
fi
echo 'Loading Linux core repo kernel ...'
linux /boot/vmlinuz-linux root=UUID=f7960d1a-77ab-4230-ab43-ff931f0b2175 ro init=/sbin/e4rat-preload quiet loglevel=3 logo.nologo console=tty1 splash=silent,fadein,fadeout,theme:arch-black
echo 'Loading initial ramdisk ...'
initrd /boot/initramfs-linux.img
menuentry 'Arch Linux GNU/Linux, with Linux core repo kernel (Fallback initramfs)' --class arch --class gnu-linux --class gnu --class os $menuentry_id_option 'gnulinux-core repo kernel-fallback-f7960d1a-77ab-4230-ab43-ff931f0b2175' {
load_video
set gfxpayload=keep
insmod gzio
insmod part_msdos
insmod ext2
set root='hd0,msdos5'
if [ x$feature_platform_search_hint = xy ]; then
search --no-floppy --fs-uuid --set=root --hint-bios=hd0,msdos5 --hint-efi=hd0,msdos5 --hint-baremetal=ahci0,msdos5 --hint='hd0,msdos5' f7960d1a-77ab-4230-ab43-ff931f0b2175
else
search --no-floppy --fs-uuid --set=root f7960d1a-77ab-4230-ab43-ff931f0b2175
fi
echo 'Loading Linux core repo kernel ...'
linux /boot/vmlinuz-linux root=UUID=f7960d1a-77ab-4230-ab43-ff931f0b2175 ro init=/sbin/e4rat-preload quiet loglevel=3 logo.nologo console=tty1 splash=silent,fadein,fadeout,theme:arch-black
echo 'Loading initial ramdisk ...'
initrd /boot/initramfs-linux-fallback.img
### END /etc/grub.d/10_linux ###
### BEGIN /etc/grub.d/40_custom ###
# This file provides an easy way to add custom menu entries. Simply type the
# menu entries you want to add after this comment. Be careful not to change
# the 'exec tail' line above.
menuentry 'Windows 7' {
set root='(hd0,1)'; set legacy_hdbias='0'
parttool "$root" boot+
chainloader '+1'
### END /etc/grub.d/40_custom ###
And my /etc/default/grub:
GRUB_DEFAULT=0
GRUB_TIMEOUT=5
GRUB_DISTRIBUTOR="Arch Linux"
# Default:
#GRUB_CMDLINE_LINUX_DEFAULT="quiet"
# Splashy boot:
GRUB_CMDLINE_LINUX_DEFAULT="quiet loglevel=3 logo.nologo console=tty1 splash=silent,fadein,fadeout,theme:arch-black"
GRUB_CMDLINE_LINUX="init=/sbin/e4rat-preload"
# Preload both GPT and MBR modules so that they are not missed
GRUB_PRELOAD_MODULES="part_gpt part_msdos"
# Uncomment to enable Hidden Menu, and optionally hide the timeout count
#GRUB_HIDDEN_TIMEOUT=5
#GRUB_HIDDEN_TIMEOUT_QUIET=true
# Uncomment to use basic console
GRUB_TERMINAL_INPUT=console
# Uncomment to disable graphical terminal
#GRUB_TERMINAL_OUTPUT=console
# The resolution used on graphical terminal
# note that you can use only modes which your graphic card supports via VBE
# you can see them in real GRUB with the command `vbeinfo'
# GRUB_GFXMODE=auto
GRUB_GFXMODE=1440x900x32
# Uncomment to allow the kernel use the same resolution used by grub
GRUB_GFXPAYLOAD_LINUX=keep
GRUB_BACKGROUND="/boot/grub/archlinux.png"
# Uncomment if you want GRUB to pass to the Linux kernel the old parameter
# format "root=/dev/xxx" instead of "root=/dev/disk/by-uuid/xxx"
#GRUB_DISABLE_LINUX_UUID=true
# Uncomment to disable generation of recovery mode menu entries
GRUB_DISABLE_RECOVERY=true
# Uncomment and set to the desired menu colors. Used by normal and wallpaper
# modes only. Entries specified as foreground/background.
GRUB_COLOR_NORMAL="light-blue/black"
GRUB_COLOR_HIGHLIGHT="light-cyan/blue"
# Uncomment one of them for the gfx desired, a image background or a gfxtheme
#GRUB_BACKGROUND="/path/to/wallpaper"
#GRUB_THEME="/path/to/gfxtheme"
# Uncomment to get a beep at GRUB start
#GRUB_INIT_TUNE="480 440 1"
I haven't updated my grub.cfg in a while because there was no need to.
Thanks in advance for advices.
Last edited by retzu (2012-04-16 14:16:02)

I have the same error message as in the first post. "error: file not found" listed three times when I first choose Arch from the Grub2 menu. The solution linked to by the.ridikulus.rat would not seem to apply as I do not have the locales en* in /boot/grub/locale BTW, I am in the US. The system does boot though.
I just fixed this a few seconds ago and was going to post how, basically I just did "cp /boot/grub/locale/[email protected] /boot/grub/locale/en_US.mo" which seem to do the trick, the reason I didn't fix this sooner is the error only stays up for a very small fraction of a second making it hard to read.
# ls /boot/grub/locale
ast.mo da.mo fi.mo hu.mo it.mo nl.mo ru.mo uk.mo zh_CN.mo
ca.mo de.mo fr.mo id.mo ko.mo pl.mo sv.mo vi.mo
EDIT: I get the same three "error: file not found" messages when I boot Fedora (a multiboot system). This is with grub2 installed from Arch Linux.
Last edited by David Batson (2012-05-02 20:03:41)

"Volume not found" I have 3 iphoto_libraries stored in a external disk, while the actual files are in other external disk. Ive moved together iphotolibraries and files but: HOW CAN I TELL THE LIBRARIES WHERE TO FIND THEM NOW?

I have three iphoto_libraries stored in a external disk PASSPORT (one for each trip imovie Im making -Ive managed this way the libraries so to not confuse the trips) while the actual files are in OTHER external disk LACIE. And everything was fine: imovie find each library, could work with it, or iphoto could edit the files.
But one day everything crashed at the same time: i opened iphoto to find 3 different scenarios:
1) iphoto_library GREECE was there, but not the albums i prepared. no events. when double click in any of them: "Volume not found"
2) iphoto_library ITALY was there, and the albums i prepared too, but empty.
in both cases I can only see the photos in 'photos' because 'events' shows some events with photo preview and some with no preview, just some kind of preset clipart palm tree, but if i enter the event, photos are there but again: when double click in any item: "Volume not found"
3) iphoto_library ISRAEL was there, the albums too, when double click in any of them: all OK
The 3 libraries was managed the same way. Meaning: Ive imported photos to iphoto from external disk LACIE in a iphotolibrary stored in another external disk PASSPORT. Also: I don't have unchecked the option "copy to file" or something like that. photos where moved, not copied. Also i have all the movie_libraries in the PASSPORT as well. What happened??
Solution? Nothing yet. Ive moved now all the photo folders from LACIE together in PASSPORT with the iphotolibraries but problem persist:
HOW CAN I TELL THE LIBRARIES WHERE TO LOOK FOR THE VOLUMES NOW?
"Volumes" are the original files aren't them?
Please help. this is so annoying to try and find in the forum, to tricky to explain
I have a Macbook pro retina Yosemite 10.10.1 / iphoto 9.6 (910-29)/ iMovie 10.0.6
THANK YOU
Vicky

The 3 libraries was managed the same way. Meaning: Ive imported photos to iphoto from external disk LACIE in a iphotolibrary stored in another external disk PASSPORT.
This is not clear, especially when you say
I don't have unchecked the option "copy to file" or something like that. photos where moved, not copied.
Especially as the message you're getting is typical of a library where the ' option "copy to file" or something like that' is unchecked.
So it's a simple question:
Are you these Managed or Referenced Libraries?
A Managed Library, is the default setting, and iPhoto copies files into the iPhoto Library when Importing. The files are then stored in the Library package
A Referenced Library is when iPhoto is NOT copying the files into the iPhoto Library when importing because you made a change at iPhoto -> Preferences -> Advanced. (You unchecked the option to copy files into the Library on import) The files are then stored where ever you put them and not in the Library package. In this scenario you are responsible for the File Management.

Payment Method supplement is not found while posting invoice thru' F-43

Dear Gurus,
I have configured Vendor Account group (OBD3) & created a vendor account (XK01).While posting thru' T code F-43,an error "Enter payment method supplement in line item 001" is found.But, payment method supplement field is not found while posting.Please solve my problem.

hi ,
In F-43 when you enter the document & posting date, company code, currency , And Vendor number PRESS ENTER it will take you to next screen There you can find the PAYMENT METHOD tab under invoice reference .
hope this will help you .

Applications Volume not found in Finder (Mac owner for 3 weeks)

Hi, I goofed today. I had an error in my Verify Disk (Below), so I thought I would boot from my OSX CDs, and fix it in Repair Disk. I ended up actually going through a new installation, choosing the non erase option. (I did not know how to boot from CDs)
However, the install would not complete. I booted from the Backup Drive and that worked well and copied the backup to my Mac HD. (Using Carbon Copy Cloner on a LaCie FireWire Drive)
All seems well except in Finder, when I select Applications, it says Volume not found. However, when I choose Applications from my Macintosh HD Volume, the Applications are there and work fine. Documents, Photos Music is all accessible from Finder left side Icons.
What do I need to do to get my system back to normal?
For future reference, how do I fix the initial problem, and how do I boot from the OS CDs
Thanks for your help
Initial Error Message in Verify Disk
Verifying volume “Macintosh HD”
Checking HFS Plus volume.
Checking Extents Overflow file.
Checking Catalog file.
Checking multi-linked files.
Checking Catalog hierarchy.
Checking Extended Attributes file.
Checking volume bitmap.
Checking volume information.
Volume Header needs minor repair
The volume The volume sh HD needs to be repaired.
Error: The underlying task reported failure on exit
1 HFS volume checked
Volume needs repair

Actually, it sounds like you have some sort of an alias problem. Just exactly where in Finder are you getting the error? Is it the Sidebar? If so, drag the Applications folder out of the Sidebar, it will go "poof"--then just drag the folder from MacHD into the Sidebar.
Francine
Francine
Schwieder

Error "Specifed Key not found" while installing Oracle 11g R2 db

Hi,
I am new to installing oracle 11gr2 DB. While installing at the stage of "install product" during the process of .Copy files its throwing the following error
*Specified Key not found
Please help me solving this problem. Your help is much appreciated.
Thanks in advance.

979400 wrote:
Hi ..
I am getting the "Specified Key not found" while installing Oracle 11 g r2 on windows 8 (64 bit) and below is the installation log , Please help me .
Number one - you are hijacking someone else's thread. Please read the forum FAQ. The link to that is conveniently located in the upper right corner of this very page.
Number two - no oracle product is certified to run on Window 8. If you want to run an Oracle product, you need to use an OS which Oracle has certified for said product.
ID: oracle.install.driver.oui.OUISetupDriver:13
oracle.cluster.verification.PreReqNotSupportedException: Reference data is not available for verifying prerequisites on this operating system distribution
     at oracle.cluster.verification.constraints.XmlTaskFactory.getTasks(XmlTaskFactory.java:248)
     at oracle.ops.verification.framework.util.VerificationUtil.isPreReqSupported(VerificationUtil.java:4538)
     at oracle.ops.verification.framework.util.VerificationUtil.isPreReqSupported(VerificationUtil.java:4487)
     at oracle.cluster.verification.ClusterVerification.isPreReqSupported(ClusterVerification.java:6382)
     at oracle.install.driver.oui.OUISetupDriver.verifyEnvironment(OUISetupDriver.java:299)
     at oracle.install.driver.oui.OUISetupDriver.load(OUISetupDriver.java:422)
     at oracle.install.ivw.db.driver.DBSetupDriver.load(DBSetupDriver.java:161)
     at oracle.install.commons.base.driver.common.Installer.run(Installer.java:216)
     at oracle.install.ivw.db.driver.DBInstaller.run(DBInstaller.java:129)
     at oracle.install.commons.util.Application.startup(Application.java:869)
     at oracle.install.commons.flow.FlowApplication.startup(FlowApplication.java:164)
     at oracle.install.commons.flow.FlowApplication.startup(FlowApplication.java:181)
     at oracle.install.commons.base.driver.common.Installer.startup(Installer.java:265)
     at oracle.install.ivw.db.driver.DBInstaller.startup(DBInstaller.java:117)
     at oracle.install.ivw.db.driver.DBInstaller.main(DBInstaller.java:148)
---# End Stacktrace #-----------------------------
---# Begin Stacktrace #---------------------------
ID: oracle.install.commons.util.exception.DefaultErrorAdvisor:16
oracle.cluster.verification.PreReqNotSupportedException: Reference data is not available for verifying prerequisites on this operating system distribution
     at oracle.cluster.verification.constraints.XmlTaskFactory.getTasks(XmlTaskFactory.java:248)
     at oracle.ops.verification.framework.util.VerificationUtil.isPreReqSupported(VerificationUtil.java:4538)
     at oracle.ops.verification.framework.util.VerificationUtil.isPreReqSupported(VerificationUtil.java:4487)
     at oracle.cluster.verification.ClusterVerification.isPreReqSupported(ClusterVerification.java:6382)
     at oracle.install.driver.oui.OUISetupDriver.verifyEnvironment(OUISetupDriver.java:299)
     at oracle.install.driver.oui.OUISetupDriver.load(OUISetupDriver.java:422)
     at oracle.install.ivw.db.driver.DBSetupDriver.load(DBSetupDriver.java:161)
     at oracle.install.commons.base.driver.common.Installer.run(Installer.java:216)
     at oracle.install.ivw.db.driver.DBInstaller.run(DBInstaller.java:129)
     at oracle.install.commons.util.Application.startup(Application.java:869)
     at oracle.install.commons.flow.FlowApplication.startup(FlowApplication.java:164)
     at oracle.install.commons.flow.FlowApplication.startup(FlowApplication.java:181)
     at oracle.install.commons.base.driver.common.Installer.startup(Installer.java:265)
     at oracle.install.ivw.db.driver.DBInstaller.startup(DBInstaller.java:117)
     at oracle.install.ivw.db.driver.DBInstaller.main(DBInstaller.java:148)
---# End Stacktrace #-----------------------------

CASE not found while executing CASE statement on Submit Form

Hi to all APEX users and developers.
I have several APEX applications and they are all working well, but recently I got one strange exception when I try to submit page:
Session: Fetch session header information
...metadata, fetch page info
...Validate item page affinity.
...Validate hidden_protected items.
Add error onto error stack
...Error data:
......message: Error processing request.
......additional_info: ORA-06592: CASE not found while executing CASE statement
......display_location: ON_ERROR_PAGE
......is_internal_error: true
......apex_error_code: APEX.UNHANDLED_ERROR
......ora_sqlcode: -6592
......ora_sqlerrm: ORA-06592: CASE not found while executing CASE statement
.....error_backtrace: ORA-06512: at "APEX_040100.WWV_FLOW", line 9273
......component.type: APEX_APPLICATION_AUTH
......component.id: 41350431648668800
......component.name: MNRFR
...Show Error on Error Page
......Performing rollback
Processes - point: AFTER_ERROR_HEADER
Processes - point: BEFORE_ERROR_FOOTER
End Page Processinga
Page has more than 120 items (most of them are hidden), so my first thought is that page has problem with posting so many items, but APEX error message doesn't hel me at all. Any help would be very appreciated :)
Almir

Hi Almir,
actually it is the 100 page item limit. See (http://download.oracle.com/docs/cd/E17556_01/doc/user.40/e15517/limits.htm)
I also had a look into the source code and the code at the position where the error gets raised only supports 100 page items.
Can you have a look into the generated HTML code and look if you have a page items which is mapped to p_t101 or a higher number ?
I will file a bug to show a better error message.
Regards
Patrick
My Blog: http://www.inside-oracle-apex.com
APEX Plug-Ins: http://apex.oracle.com/plugins
Twitter: http://www.twitter.com/patrickwolf

" APPLICATION NOT FOUND" while deploying Web dynpro java Application

Hi, I am getting a message that "application not found " While deploying the web dynpro java application .......... please give me a solution for this .

Hi Ram,
This error comes generally when your webdynpro project does not have an application. To create an application in your webdynpro project follow the underlying steps:
<Project>->WebDynpro->Applications ---> right click and create New Application.
Follow the steps to create the application.
Now if you create archive and deploy, it will not give you the error again.
Best Regards,
Ravi

Error 404 -- Not Found while accessing weblogic console

Hi
I get Error 404 Not Found while accessing the console or any other application
which is deployed on the server
while the server is running even i have restarted my server
it shows server running in the log files as well as on the command console .
but when i try to access console or any other application it gives me error page
404 Not Found
I am using weblogic 7 with SP2 on solaris
So please help me in debugging the problem
Thanks in advance....
Pratap

Hi
I get Error 404 Not Found while accessing the console or any other application
which is deployed on the server
while the server is running even i have restarted my server
it shows server running in the log files as well as on the command console .
but when i try to access console or any other application it gives me error page
404 Not Found
I am using weblogic 7 with SP2 on solaris
So please help me in debugging the problem
Thanks in advance....
Pratap

Extensions are not loaded while boot

Hi there!
I have the problem, that the driver für my firewire audio interface and the driver for my dsp cards are not loaded while booting the system...
How can I activate these extensions?
Thank you for support!
Cheers
André

Are you talking about kext's? Did you check that they are even there (look in /System/Library/Extensions or type kextstat in terminal).

Getting error "Http 404 not found" while accessing CUCM GUI..

Hi,
Please help um getting error "Http 404 not found" while accessing CUCM GUI. Yesterday it was running fine bt nw its showing dis error.
Please find attached screenshot for ur referance.
Thanks & R's
Harish

Hi Aaron,
I have restarted dat service bt still the issue is persisting.
Now its showing attached error.
Thanks and R's
Harish

HTTP 404 Not Found while accessing Human Resource Intelligence functions

Hi,
Can anyone help me in resolving
HTTP 404 Not Found while accessing Human Resource Intelligence functions
error
Instance : R12
Thanks

Hi,
Apache log file is not showing any errors.What log files have you checked? Please check error_log and access_log files, you should find more details about the error in these logs.
Thanks,
Hussein

IPlanet 6.0 and struts (Extension of file not found, while displaying stati

i am trying to launch the strut appln in iPlanet 6.0 when i am making a reqest for jsp i am getting a message saying Error: 404 SC_NOT_FOUND
Extension of file not found, while displaying static content . i do not have any clue on this why i am getting this message.
Could anybody help me regarding this

Hello,
I am experiencing the same problem too. My jsp accesses a javabean. I
noticed, most of the times, I thought, it happened when session was timed
out. But it also happended before the time-out too. I had it set as default
at 30 minutes.
If you find out a solution or some high lights please let me know.
Thanks a lots.
ThuThien Ho
[email protected]
(703) 428-2856
Jordi Lucas wrote:
Hi all,
I have the following problem.
When I try to execute a jsp, the server responds:
Error: 404 SC_NOT_FOUND
Extension of file not found, while displaying static content
This problem doesn't ocurred with all jsp's, it seems that only ocurrs
with the jsp's that call EJB's or JavaBean's.
Anyone has encountered with the same problem?
Any idea?
We are using Iplanet Application Server 6.0 SP3 and IPlanetWebServer 4.1
SP7.
Thanks in advance !
Jordi Lucas Essi Projects
Ingeniero de desarrollo
[email protected] t +34 977 221 182
http://www.essiprojects.com f +34 977 230 170

[SOLVED] LVM Volume Groups Not Found

Hi,
I'm installing Arch on my desktop following the installation in the software raid and LVM section (https://wiki.archlinux.org/index.php/So … ID_and_LVM). I'm using RAID1. I've followed the important instructions on the LVM page (https://wiki.archlinux.org/index.php/LVM#Important). I have a UEFI motherboard so I created a separate boot partition and installed grub2 as my bootloader based on the instructions on the UEFI page (https://wiki.archlinux.org/index.php/Un … _Interface).
After a few hiccups, I think I have the system installed properly on my hard drive. Since the root partition is on the LVM, it needs to be loaded up pretty early in the boot process and this is where I'm getting a really strange issue. I have my motherboard configured to boot straight into the built-in UEFI shell. From here, I select the filesystem for my hard drive and launch grubx64.efi. So far so good. Now here's the weird part - if the LiveCD I used to install Arch is in the optical drive then everything boots up just fine, I get a prompt and I can log in and generally do as I see fit. But if the LiveCD isn't in the drive, then after I select the Arch Linux option in GRUB I get a message that says No Volume Groups found and dumps me into the rootfs shell.
As far as I can tell the LiveCD isn't actually being used during boot, but I don't understand why taking it out stops my logical volumes from loading =_=. Does anyone have some idea what's wrong / what I can do to fix it? Is there some config file that has been messed up? This is my second time trying this installation, if it doesn't work I'm just going to drop LVM and stick to just the software RAID. I'm not particularly attached to LVM, I decided to use it mainly because I could (or at least I thought I could).
Any help would be much appreciated. If there is any extra information I need to post, I can do that as well.
Update: It doesn't seem like the Arch LiveCD itself has anything to do with this. I inserted a blank CD and was able to boot up just fine but as soon as I took it out, I got the No volume groups found error again. This makes me think that it is a timing issue. Maybe one of the modules is not fully loaded before it is needed? Where can I go to find out what modules those are? Is there any way to force the boot process to wait until all the necessary modules are loaded?
SOLUTION: https://bbs.archlinux.org/viewtopic.php?id=145714
Last edited by jynnantonix (2012-09-07 19:30:01)

What you did has zero effect on the runtime order of the hooks (lsinitcpio would have shown you this).
https://bbs.archlinux.org/viewtopic.php?id=145714

[SOLVED] LVM volume not found while booting

Similar Messages

Maybe you are looking for