Some Windows 8 users cannot connect to 1142N Autonomous

Hi folks,
I have got an issue with some Window 8 devices here. I am not sure if this is a misconfiguration or firmware issue.
Please have a look my config. Any help will be highly appreciated.
Thanks.
hostname QXAP2
logging rate-limit console 9
enable secret 5 $1$aQGz$y42twDoPdQJgJasegu0oj.
no aaa new-model
no ip routing
no ip cef
ip dhcp-server 192.168.0.50
dot11 syslog
dot11 ssid QXAP2
vlan 1
authentication open
authentication key-management wpa version 2
guest-mode
wpa-psk ascii 7 09415718015445414F
dot11 network-map
dot11 guest
crypto pki trustpoint TP-self-signed-1329179707
enrollment selfsigned
subject-name cn=IOS-Self-Signed-Certificate-1329179707
revocation-check none
rsakeypair TP-self-signed-1329179707
crypto pki certificate chain TP-self-signed-1329179707
certificate self-signed 01
quit
ip ssh version 2
bridge irb
interface Dot11Radio0
no ip address
no ip route-cache
encryption vlan 1 mode ciphers aes-ccm tkip
ssid QXAP2
antenna gain 128
station-role root
interface Dot11Radio0.1
encapsulation dot1Q 1 native
no ip route-cache
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 spanning-disabled
bridge-group 1 port-protected
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
interface Dot11Radio1
no ip address
no ip route-cache
shutdown
antenna gain 0
peakdetect
no dfs band block
channel dfs
station-role root
interface Dot11Radio1.1
encapsulation dot1Q 1 native
no ip route-cache
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 spanning-disabled
bridge-group 1 port-protected
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
interface GigabitEthernet0
no ip address
no ip route-cache
duplex auto
speed auto
interface GigabitEthernet0.1
encapsulation dot1Q 1 native
no ip route-cache
bridge-group 1
bridge-group 1 spanning-disabled
no bridge-group 1 source-learning
interface BVI1
ip address 192.168.0.254 255.255.255.0
ip helper-address 192.168.0.50
no ip route-cache
ipv6 address dhcp
ipv6 address autoconfig
ipv6 enable
ip default-gateway 192.168.0.1
ip forward-protocol nd
ip http server
ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
ip route 0.0.0.0 0.0.0.0 192.168.0.1
bridge 1 route ip

Your using WPA2, so you should just use aes:
encryption vlan 1 mode ciphers aes-ccm

Similar Messages

Updated to 10.6.3, Windows users cannot connect anymore

Up to 10.6.2 my mac was able to do SMB file sharing with Windows users. After this update, they are unable to connect with the mac.

Gerry, thanks so much for your post. In the meantime, though, here's what I've been doing (it seems to work, though it's taking time; I just hope it's the right thing to do):
- I open a year's worth of photos, and choose one; control-click and choose 'Locate Referenced Files'.
- this brings up a huge window; at the top is the photo I'd selected. In the bottom half of the window I can navigate to the right year's folder in my 'Pictures' folder, and then to the right folder in this year, and in fact navigate right down to the exact photo. Once I've selected this photo in the lower half of the window the 'Reconnect all' button (that's been greyed out until now) is selectable. I choose it, and the whole year's photographs are re-referenced.
That seems to do it.
I'd like to have been able to do it more simply and quickly (I like the sound of your plan), but in the half-hour that I was waiting, I thought I'd try something and this seems to work. Let me know what you think of my strategy if you have the time and inclination.
Regards, Malcolm

Lion-Windows users cannot see attachments

I just upgraded to Lion, and now some Windows users cannot see/find attachments. I did all that was advised (clicking on the "Windows user friendly" list), but to no avail. I sent to several Windows users and no one can see attachments with the new Mail program. Also, one of the most important icons in the Mail toolbar ("Add Attachment") seems to be missing. This sometimes helped in previous Mail versions when sending to PCs, but I cannot locate it in Lion. Looks like I will have to use Microsoft Office Outlook for email. This is too bad, as I like the other features the new Apple Mail program has, but must use a trustworhty email program.

Scott,
The issue is one I am chasing, and is due to Lion's change to not send Plain Text (apparently). Although changed in the Compose window, when reviewed, it will have been sent with HTML, anyway.
While the actual problem is with MS and Outlook or Outlook Express, the work around once was to use the command to Make Plain Text before sending.
Ernie

Hi All, I am trying to install informatica 9.1 HF 2 connecting to 11g DB. when installing Informatica, I am at the DOMAIN CREATION windows and inputting the DB connect details and for some reason, it cannot connect to the DB. The DB is running any id

Hi All,
I am trying to install informatica 9.1 HF 2 connecting to 11g DB.
when installing Informatica, I am at the DOMAIN CREATION windows and inputting the DB connect details and for some reason, it cannot connect to the DB.
The DB is running
any ideas?
the error message states:
THE CONNECTION FAILED: CORRECT THE DATABASE INFO AND TEST THE CONNECTION AGAIN..any help please
thanks

Yup, that did it.
I actually had been made aware of the patch when I downloaded CF, but for some reason I thought it was difficult to install (I thought that you could only use the installer package if you could open Administrator). IAC I downloaded the appropriate patch file, ran it and Administrator ran. There was something in the install notes about reconfiguring the websites and removing the IIS6 Management feature but I'm not going to fool with anything because right now at least CF is running.
Thanks.

Windows SMB users cannot connect to 10.5.4 server

Hi all,
Have a server running 10.5.4 bound to AD and running an OD to provide management of the Macs. Pretty standard setup and haven't had any problems elsewhere with the same deployment. However we're having a problem with XP users connecting to SMB shares. Mac users can connect over AFP or SMB fine, XP users are getting a "Network path could not be found" error. What's more the errors in the SMB log on the server aren't too descriptive. We're getting a few broken pipe errors, but no indication of what's causing that. XP machines don't appear to be getting to the authentication stage.
Server is an Xserve with a Promise RAID, shares are on a 4TB partition, bound to AD (OD not running Kerberos). SMB setup seems to be correctly aware of the AD.
Anyone any ideas?
Thanks

Is your SMB a Standalone or Domain Member?
I have a similar problem and noticed that if I change SMB from "Domain Member" to Standalone Windows users can connect. Now every so often Leopard Server will change SMB back to a Domain Member (automatically).
I have the Server bound to AD. AFP works for the Macs no matter what. Mac Users authenticate to AD and mount the share. However if they try to use SMB, it fails for the Macs as well if SMB is a Domain Member.
I would like to stop Leopard from not reverting back or fix the "domain member" problem.
The fact that I can connect while it's a Standalone suggests, to me, that it's not a permissions problem. As well the failure carries to the Mac side means it's not a Windows issue.

Sharing only users cannot connect to Lion Server

Dear all,
I stumbled across a funny problem, that I tried to resolve all day. I just wanted to add a sharing only user for my girlfriends new MacBook that she could use to connect to a shared Time Machine Volume.
If I add a new standard user, this user can connect to my server via finder (connect as...) and see the shared drives. If the same user tries to connect to the Time Machine Backup Volume via the settings dialog, it receives an error message (OSStatus-error 5).
If I add a sharing only user, this user cannot connect via finder or Time Machine (same error). The clients console states the following error message:
/System/Library/CoreServices/NetAuthAgent.app/Contents/MacOS/NetAuthAgent[2471] AFP error -5018 mapped to EIO
Does anybody have an Idea?

That is my point. Yes, Apple still lets you add users via users and groups in system preferences but that is not how you should be adding users. I've seen nothing but trouble when that option is used to add users and I believe that the Lion server docs say to not use that. If you are using lion server why not use it the way it was meant to be. Just create a account in OD and only give her access to the Time Machine Service and none of the others.

Users cannot connect over SMB 10.10.1 server.app 4.0 and 4.0.3

Hello,
I have an issue where users cannot connect to a server for files sharing over SMB.
Info:
All users on 10.10.1
2 Servers on 10.10.1
Server.app 4.0.3 but issue was also present using 4.0
SMB connection works when connecting to the OD Master
SMB does not work when connecting to the OD Replica ServerBut AFP works fine when connecting to the OD Replica Server.
I have destroyed and re-added the OD replica but that did not seem to help
This is what I see in the logs each time I try to connect(logs have been cleaned to remove client details:
Jan 9 14:37:12 server.pretendco.com digest-service[9961]: label: default
Jan 9 14:37:12 server.pretendco.com digest-service[9961]: dbname: od:/Local/Default
Jan 9 14:37:12 server.pretendco.com digest-service[9961]: mkey_file: /var/db/krb5kdc/m-key
Jan 9 14:37:12 server.pretendco.com digest-service[9961]: acl_file: /var/db/krb5kdc/kadmind.acl
Jan 9 14:37:12 server.pretendco.com digest-service[9961]: digest-request: uid=0
Jan 9 14:37:12 server.pretendco.com digest-service[9961]: digest-request: netr probe 0
Jan 9 14:37:12 server.pretendco.com digest-service[9961]: digest-request: init request
Jan 9 14:37:12 server.pretendco.com digest-service[9961]: digest-request: init return domain: SERVER2 server: SERVER2 indomain was: <NULL>
Jan 9 14:37:13 server.pretendco.com digest-service[9961]: digest-request: uid=0
Jan 9 14:37:13 server.pretendco.com digest-service[9961]: digest-request: init request
Jan 9 14:37:13 server.pretendco.com digest-service[9961]: digest-request: init return domain: SERVER2 server: SERVER2 indomain was: <NULL>
Jan 9 14:37:13 server.pretendco.com kdc[4802]: Got a canonicalize request for a LKDC realm from local-ipc
Jan 9 14:37:13 server.pretendco.com kdc[4802]: Asked for LKDC, but there is none
Jan 9 14:37:13 server.pretendco.com sandboxd[395] ([4802]): kdc(4802) deny file-read-data /private/etc/krb5.conf
Jan 9 14:37:22 server.pretendco.com kdc[4802]: Got a canonicalize request for a LKDC realm from local-ipc
Jan 9 14:37:22 server.pretendco.com kdc[4802]: Asked for LKDC, but there is none
Jan 9 14:37:23 server.pretendco.com digest-service[9961]: digest-request: uid=0
Jan 9 14:37:23 server.pretendco.com digest-service[9961]: digest-request: init request
Jan 9 14:37:23 server.pretendco.com digest-service[9961]: digest-request: init return domain: SERVER2 server: SERVER2 indomain was: <NULL>
Jan 9 14:37:23 server.pretendco.com digest-service[9961]: digest-request: uid=0
Jan 9 14:37:23 server.pretendco.com digest-service[9961]: digest-request: init request
Jan 9 14:37:23 server.pretendco.com digest-service[9961]: digest-request: init return domain: SERVER2 server: SERVER2 indomain was: <NULL>
Jan 9 14:37:23 server.pretendco.com digest-service[9961]: digest-request: uid=0
Jan 9 14:37:23 server.pretendco.com digest-service[9961]: digest-request: od failed with 2 proto=ntlmv2
Jan 9 14:37:23 server.pretendco.com digest-service[9961]: digest-request: user=SERVER2\\username
Jan 9 14:37:23 server.pretendco.com digest-service[9961]: digest-request: kdc failed with 36150275 proto=unknown
Jan 9 14:37:23 server.pretendco.com digest-service[9961]: digest-request: guest failed with -1561745590 proto=ntlmv2
Jan 9 14:37:23 server.pretendco.com digest-service[9961]: digest-request: uid=0
Jan 9 14:37:23 server.pretendco.com digest-service[9961]: digest-request: init request
Jan 9 14:37:23 server.pretendco.com digest-service[9961]: digest-request: init return domain: SERVER2 server: SERVER2 indomain was: <NULL>
Jan 9 14:37:23 server.pretendco.com digest-service[9961]: digest-request: uid=0
Jan 9 14:37:23 server.pretendco.com digest-service[9961]: digest-request: init request
Jan 9 14:37:23 server.pretendco.com digest-service[9961]: digest-request: init return domain: SERVER2 server: SERVER2 indomain was: <NULL>
Jan 9 14:37:23 server.pretendco.com digest-service[9961]: digest-request: uid=0
Jan 9 14:37:23 server.pretendco.com digest-service[9961]: digest-request: od failed with 2 proto=ntlmv2
Jan 9 14:37:23 server.pretendco.com digest-service[9961]: digest-request: user=SERVER2\\codywood
Jan 9 14:37:23 server.pretendco.com digest-service[9961]: digest-request: kdc failed with 36150275 proto=unknown
Jan 9 14:37:23 server.pretendco.com digest-service[9961]: digest-request: guest failed with -1561745590 proto=ntlmv2
I suspect the problem is to do with Kerberos and in relation to this server being an OD Replica.
I would really appreciate anyone's insight into this.
Thanks
Morgs

I have the same problem although I upgraded from Lion Server to Mountain Lion Server. The error appears to go hand in hand with this error.
userInit: CFPreferences: user home directory for user kCFPreferencesCurrentUser at /Network/Servers/fullyqualifieddomainname/Users/user is unavailable. User domains will be volatile.
I've read a number of things to try. A lot of people point to DNS being a problem, but I'm confident this is correct in my environment.

Some windows-user could not see all images on the print result

We have a Problem when printing images (blobObject).
We are printing all displayed images immediately on the report. The images are represented on the report by Blob objects. At runtime we create a Bitmap object in memory, which is stored in a memory stream, the byte array of MemoryStream is placed in the field of the DataSet, which has deposited on the report as BlobObjekt.
The error that occurs is that some Windows-User didnu2019t see all pictures. But without any Errormessage, the picture is still white.
All users use the same Windows-PC with the Crystal Report Version 10.2.3600.0 .
The difference between the pictures is simple:
Picture 1)
-     Note: This picture appears properly
-     This one exists as JPG-File on the harddisk
-     We read the image, convert it into a memory stream and place the byte array in de DataSet-Field
-      This images are positioned in the header and footer section
Picture 2)
-     Note: this picture does not display properly
-     This one is created by the application
-     It is created in memory by an graphics-object
-     This graphics-Object is converted into an memory stream and so on
-     This images are positioned in the details section
Here are the piece of code, which is the dataset supplied with pictures. (abbreviated version)
Using stream As IO.MemoryStream = New IO.MemoryStream
Using dest As Bitmap = New Bitmap(field.Width, field.Height)
            Using gd As Graphics = Graphics.FromImage(dest)
gd.Clear(Color.White)
gd.DrawImage(Source, destrect, sourcerect, GraphicsUnit.Pixel)
dest.Save(stream, System.Drawing.Imaging.ImageFormat.Bmp)
            End Using
      End Using
ds.Tables(datasourceTableName).Rows(j)(datasourceName) = stream.ToArray
stream.Close()
End Using
Has anyone an ideo whats going wrong?
The logic to print the images is always the same only the windows user is different.

Is this a web or windows based application?
Is this happening on the same computer but with a different user? It could be a user rights issue. Try using the Process Monitor tool to see if it is highlighting any permissions issues.
Regards,
Jonathan

Windows users cannot open my Pages documents

Even though I check Windows Friendly Attachment, Windows users cannot open my Pages documents. Is there anyway to fix this problem?

KOENIG Yvan wrote:
I decided that I will not replicate what is printed in the available documents.
If the only questions we're going to answer are the ones that aren't already answered in the manual, then these discussions will consist of little more than directing people to page numbers. Yes, it would be nice if people read the manual before posting here. But everyone's brain works a little differently, and I don't mind if nice people ask questions that can be solved by reading the manual or doing a search in this discussion group. Even figuring out how to find things in the manual isn't intuitive to a lot of people.
In terms of helping people, it's actually a lot less work to provide a solution for them than to look it up in the manual, then come back and report the page number.
We have a saying in America that goes like this: Different strokes for different folks. You can thank Sly and the Family Stone for that one.
-Dennis

User cannot connect to backend system with user J2EE_ADMIN.

I am using Rapid Installer to initiate the second part of the installtion "ERP 6.0 EhP 3 Self-Service Scenarios and Automatic Roles". When I get to the J2EE User section to enter the parameters, the user is defaulted to "Administrator" and I enter my password. I click next and get this message "User cannot connect to backend system with user J2EE_ADMIN." Any ideas?

If this is a double stack installation, you need to enter J2EE_ADMIN as user, NOT administrator.
Markus

How to specific some of user cannot be locked.

Dear Sir,
As we set to lock EP user when 3 times for wrong password, however, I need some of users cannot locked (out of rule). However, I don't know how to set some users cannot lock.
Please kindly advise.
Thank you and best regards,
Vimol

Hi Vimol,
You can change the number of login attempts in the Visual Admin. Here is the <a href="http://help.sap.com/saphelp_nw2004s/helpdata/en/ee/10df3d0eb8af5ee10000000a114084/frameset.htm">Link</a>.
You can set the ume.logon.security_policy.lock_after_invalid_attempts to 0(zero) so that it never locks when invalid login credentials are given
Ok, I believe Goutam Reply is more appropriate, mine answer is for all the portal users!!
Thanks,
Vijay
Message was edited by:
Vijaya Saravanan Jayachandran

External users cannot connect to RDS Farm (Azure).

Hi Experts,
I hope someone is able to help me with this. I have search high and low, but have not found a solution.
Here we go:
I have setup a RDS Farm in Microsoft Azur, consisting of the following servers:
KRPDC01 (Domain Controler / Active Directory / DNS Server)
KRPSH01 (Remote Session Host #1)
KRPSH02 (Remote Session Host #2)
KRPCB01 (Connection Broker)
I have installed the respective Remote session roles on the above server and added my group of users to the "Remote Desktop Users" group on each Session Host server.
At first glance it seems to work. I seem to be able to connect to the farm with the first user. But most of the times, when a second users tries to connect to the same farm, then login hangs for a time, and the connection is refused with this message:
"Remote Desktop cannot connect to the remote computer for one of the following reasons:
1) Remote Access to the server is not enabled
2) The Remote Computer is turned off
3) The Remote Computer is not available on the network
Make sure that the remote computer is turned on and connected to the network, and that remote access is enabled."
Sometimes not even the first user can connect to the farm at all with the same error message.
I have looked into the logs on the connection broker, and something interesting shows up.
It seems that whenever the connection broker wants to redirect a users connection request to a different server than the one that recieved the connection request, then the connection fails. If however the connection broker grants the connection to the same
server as the request is comming from, then the user is logged in.
Here are the log entries when the connection fails:
"RD Connection Broker received connection request for user xxx\testuser.
Hints in the RDP file (TSV URL) = tsv://MS Terminal Services Plugin.1.KRPCLOUD
Initial Application = NULL
Call came from Redirector Server = KRPSH01.xxx.net
Redirector is configured as Farm member"
Followed by:
"RD Connection Broker successfully processed the connection request for user xxx\testuser. Redirection info:
Target Name = KRPSH02
Target IP Address = 10.4.3.7
Target Netbios = KRPSH02
Target FQDN = KRPSH02.xxx.net
Disconnected Session Found = 0x0"
The a few minutes later this entry is found in the log:
"Remote Desktop Connection Broker Client failed to redirect the user xxx\testuser
Error: NULL"
These are the log entries when the connection is successfull:
"RD Connection Broker received connection request for user xxx\testuser
Hints in the RDP file (TSV URL) = tsv://MS Terminal Services Plugin.1.KRPCLOUD
Initial Application = NULL
Call came from Redirector Server = KRPSH02.xxx.net
Redirector is configured as Farm member"
Followed by:
"RD Connection Broker successfully processed the connection request for user xxx\testuser. Redirection info:
Target Name = KRPSH02
Target IP Address = 10.4.3.7
Target Netbios = KRPSH02
Target FQDN = KRPSH02.xxx.net
Disconnected Session Found = 0x0"
And then:
"Session for user KASSERAPPORTEN\krptest successfully added to RD Connection Broker's database.
Target Name = KRPSH02.kasserapporten.net
Session ID = 2
Farm Name = KRPCLOUD"
And:
"This connection request has resulted in a successful session logon (User successfully logged on to the end point). Remote Desktop Connection Broker will stop monitoring this connection request."
If I connect to one of the other servers on the network - the KRPDC01 - and from there connects to the RDS Farm (internally) then there is no problem recieving the connections. Also connections where the broker has to redirect the connection to a differing
Session Host is completed without problems.
I have noticed than when successfully connection from internally where the connection is redirected by the connection broker, then I actually recieved 2 certificate warnings. One first from the Session Host that have recieved the connection request, and the
shortly after from the second Session Host (when the connection broker is redirecting the connection) and then the connection is established.
When connection from the outside, I never get the second certificate warning.
In Azure I have setup indpoint for Remote Desktop - TCP/3389 on both Session Host servers and on the Connection broker.
As mentioned I am at a total loss, and I hope someone out there is able to help me solve this issue.
Thanks in advance :-)
Regards,
Daniél

Hi,
Seems this issue is related with Windows Azure Virtual Machine, I will move it to Windows Azure Virtual Machine Forum for a better help.
Thank you for your understanding!
Best Regards
We are trying to better understand customer views on social support experience, so your participation in this interview project would be greatly appreciated if you have time. Thanks for helping make community forums a great place.
Click
HERE to participate the survey.

Domain users cannot connect to the network folders when logged in via rds remote apps

Hi,
recently I setup an RDS farm for remote apps on server 2012 r2.
all users can connect to the apps published. no problems there.
but when users connect via rds they cannot connect to the networkfolders and cannot store the resultance of there work (docx and xlsx files)
all users are normally connected to the networkfolders using a small login batch file handing down the unc path needed. when I log in as domain admin, also using a login batch, connections are setup correctly. It seems to me to be an security issue on the
rds session host.
how to alter this?
greetz, Fons
Fons system and network engineer Balie Amsterdam

Hi,
Thank you for posting in Windows Server Forum.
We use WMI to communicate with the RDSH server. Various issues can cause WMI to deny access or return error codes. Here's a few things you can try:
1. Check if the "TS Web Access Computers" security group on the RDSH server has incorrect permissions in DCOM and/or WMI:
For checking DCOM security settings:
1. Start the Component Services MMC snapin
2. Navigate to Component Services -> Computers -> My Computer
3. Right-click on My Computer and select properties
4. Go to the COM Security tab
5. Under Access Permissions, click the Edit Limits button
6. Ensure that TS Web Access Computers is in the list, with all of the permissions set to “allow”.
7. Under Launch and Activation Permissions, click the Edit Limits button
8. Ensure that TS Web Access Computers is in the list, with all of the permissions set to “allow”.
For checking WMI security settings:
1. Start the WMI Control MMC snapin
2. Right-click the WMI Control node and select properties
3. Go to the Security tab
4. Navigate to Root->CIMV2->TerminalServices
5. With TerminalServices selected, click the Security button
6. Ensure that TS Web Access Computers is in the list with Execute Methods, Enable Account, and Remote Enable set to "allow"
2. Verify the RD Session Host server's firewall allows WMI calls.
3. Verify that the RD Connection Broker hasn't lost its trust relationship with the domain.
4. See if non-RDS related WMI calls can be successfully made to the RDSH server. This can help differentiate between a general WMI issue and an issue calling the RDS WMI provider.
(Quoted from following thread.)
RemoteApp Source not working from RDWeb
http://social.technet.microsoft.com/Forums/windowsserver/en-US/173d4546-e12f-47c1-ac66-8b4f69826892/remoteapp-source-not-working-from-rdweb?forum=winserverTS
Hope it helps!
Thanks.
Dharmesh Solanki

Windows XP cannot connect/logon to my iMac that has 10.5.8

I tried searching the forum and could not find this exact problem, so I hope I am not re-asking the same question....
I just upgraded from a 7-year-old G4 system running Tiger, and am having issues logging in as a user from a PC to the new Leopard system.
I am trying to logon/connect with my new (June 2009) iMac from a laptop running Windows XP Home, on my home network via AirPort. In Sharing, I have the "File Sharing" box ticked, and the AFP and SMB boxes ticked in the "Options" window, as well as the account that I want to be able to log in with. In the "Shared Folders" column, I have the hard drive and the user account listed, that I want shared. The permissions are set to Administrator(s) can read & write and everyone else can only read.
On the XP system, in Workgroup, I can see the iMac, but when I double-click it, NO request for a username and password comes up. Instead you can see the shared folders, and navigate through them. However, you CANNOT open any files or folders, getting a error message saying that you do not have permissions for these networt resources and that access is denied.
What is happening?
I can still log in fine to the old Tiger system, and the Tiger system can log in fine to the Loepard system and vise-versa, but I CANNOT log into the Leopard system from the XP Home PC.
I have looked around online and see mention of smb problems with Leopard, but no sure answers, that I can see.
Please help - thanks in advance!

Hello,
I am having a similar issue with Mac OS 10.5.8.
I upgraded about 1 week ago and since I cannot see my shared folders in the Finder, and I cannot connect to them anymore using SMB. On the other hand my TimeCapsule works fine.
The first symptoms I noticed were that my Windows XP Pro shared folders were no more visible from the Finder. After checking it I tried to connect to them using the Apple+K command. There I can see the share, it asks me which disk I want to mount then when I select one, I get an error -6602.
The weird thing is when I am at home I can see my timecapsule appearing directly in the Finder but not any other share.
Also I have noticed it to be almost impossible to share folders from my Mac OS to other machines. We have a few Windows and Linux at work, I used to share data with them but now, it is impossible for them to see me, or access my shared folders. And this is not due to bad access right, I have checked a number of time.
Anyone has any ideas on what do I do? or how I can solve this issue? I am considering just reinstalling the laptop completely but this is a huge time consuming job that I would rather not do!
Thanks,
Ced
Message was edited by: tuxy94

Oracle ebs multiple concurrent, locks, user cannot connect to app.

We had experienced outage yesterday afternoon, Oracle EBS app users cannot log into the app. We noticed very high load 70-90% in Grid control, and multiple blocks, a rman job still running and one stats job running. However seems after killing a dbms_scheduler job of app report, we fixed the issue.
However this morning, we still see cpu load of 70% and on grid control concurrent locks and transactions all in huge red.
I would like all Gurus here help me to start how to diagnose in Oracle ebs.
I would like to start from very beginning.
Such as links I can read, what to look at inside the database? on hosts?
Thanks a bunch.

I think those sessions we killed are some inactive sessions hanging around since Feb. I am new to this company, so I am not really sure how those jobs started. but seems they scheduled through window control m, something like that.
anyway,
Last night I digged into grid control, and moved the history data to the date/time of the incident.
and I found out a lot sql tuning advisors during the time being, and several queries showed up in the sql tuning advisor and it required tuning. explain plans shows they are doing quite a lot full table scans for some big tables . I will add a screenshot soon.
So I wonder if those are the main causes.
Data SourceSnapshot (34294)Capture TimeNov 3, 2013 10:00:44 AM (UTC-06:00)
TABLE ACCESS FULL
AR.HZ_CUST_ACCOUNTS67427.971K01000:0:1SEL$335DD26A / CUST_ACCT@SEL$3
TABLE ACCESS FULL
AR.HZ_PARTIES81,59440.473K01700:0:1SEL$335DD26A / PARTY@SEL$3
SORT AGGREGATE
1211400
0:0:0SEL$4
TABLE ACCESS BY INDEX ROWID
CLC.RESERVATION_ROOMS113420400:0:1SEL$4 / X@SEL$4
INDEX RANGE SCAN
CLC.RES_ID10300300:0:1SEL$4 / X@SEL$4
INDEX RANGE SCAN
CLC.RES_ID133180300:0:1SEL$5 / X@SEL$5
HASH UNIQUE
29221.998K021,28110:4:16SEL$6
FILTER
TABLE ACCESS FULLCLC.RESERVATION_ROOMS161,138,95015.207M04,14810:0:50SEL$6 / RESERVATION_ROOMS@SEL$6
TABLE ACCESS FULL
CLC.RESERVATION_HEADERS17944,34344.129M08,12610:1:38SEL$6 / RESERVATION_HEADERS@SEL$6
INDEX RANGE SCAN
CLC.RESERVATION_LOGS_N1192
I would like to know how come there were sql tuning advisors running during times other than 22pm as scheduled auto job. So is that means whenever there is a issue query, the sql tuning advisor automatically kick in?
The advisor basically said need to rewrite the query to take advantage of the indice.
Thanks,

Some Windows 8 users cannot connect to 1142N Autonomous

Similar Messages

Maybe you are looking for