Spa3000 or Spa3102 back to back telephone line extension instrucations

              Ive got a set of spa3000`s and spa3102 and what I want to do is use them just to extend a telephone line about 2 miles and pick it up on the other end and use a anolog phone. I will be using a set of maxstream 900mhz ethernet radios for the ethernet bridge. I have pulled everything from the net that I could find on the configuration but no go on the 3000`s. Most info is written for the 3102`s but it pretty close.  Can someone point me in the right direction on what Iam missing, for instance  you ip both but theres no mention on weather dhcp server should be on or off. Also do I use a straight or cross over cable when tying into my bridges.  Any help would be apprecated. Right as this writing Iam going to unbox the 3102`s and give them a shot but would really like a detailed configuration plan if any one has one
Thanks  ahead of time

I think this is what you are looking for.
PBX Port Extension over LAN using SPA 2102 / 3102
https://supportforums.cisco.com/thread/2149426
The steps are basically the same for most Cisco SPA devices. 
make sure you update the firmware to the latest.
I don't know about your converters/extenders, but test the extension seperately from the layer 1 connectivity, so you don't have to troubleshoot multiple issues.
hope it helps,
Dan

Similar Messages

  • Telephone line Extensions over Ethernet via SPA112 ?

    I saw a recommendation elsewhere and on this forum suggesting the SPA112 coul be used to extend phone lines (same number) to other rooms over ethernet.
    Here is what I want to do:
    I have exsiting IP based phone service provided by a company called Talkit (Canada). Talkit provided at Grandstream Handytone 286 ATA and I connected a cordless Nortel analog phone to it. Works ok.
    Now I want to put an extension of the same phone number into another room. I purchased two SPA112s to try to do this. I have established ethernet connectivity and I can see and configure both units.
    I connetced one unit to the phone line that runs from the Handytone ATA to my analog phone to one SPA112 and a second old analog phone in the second room to the second SPA112.
    I made the following config changes:
    I upagraded the FW to the latest version on both SPA112 units.
    I set
    Register to No
    Use OB proxy to No
    Make calls wo reg to Yes
    Ans call w/o reg to Yes.
    I was able ot get a dial tone on the second phone but when I dialed out to my cell phone I geta busy signal.
    Another issue is that the SPA112 connected to the Handytone ATA seems to stay OFF Hook.
    Please advise... or point to a document where I can read about how to set these up.
    I am assuming that I do not need to register the spa112s to my service provider proxy bu that rather that two spa112s will simply pass the incoming and outgoing calls thru.
    John

    John,
    Both the Grandstream Handytone and the SPA112 are what are called "ATA" devices. "ATA" stands for Analogue Terminal (or in some literature, Telephone) Adapter. That's to say that an ATA device converts from an IP-based voice connection to an analogue voice connection.
    The port that you connect your cordless phone to on the Grandstream ATA is, technically, referred to as an FXS port. An FXS port provides dial tone and battery voltage on an analogue line. The compliment to an FXS port, is an FXO port, which expects to have dial tone and battery voltage provided to it. Both the Handytone and the SPA112 have only FXS ports, so they all provide dial tone and battery, and thus are not compatible to be connected directly together.
    You would need a device (such as the previously mentioned SPA3102) which features an FXO port on one end of the ethernet connection, and one of your SPA112 ATA's on the other end of the ethernet connection.
    If I'm understanding what it is you're trying to accomplish correctly (and I believe I do), there are a couple suggestions I would make.
    First off, you can contact TalkIt, and explain that you wish to configure your own ATA device with their service, in addition to the one they provided you. They would need to provide you the SIP proxy and credential information for your phone accounts with them. You would then need to program that information into the SPA112 that is in the second room. As long as that SPA112 can get internet connectivity, it should be able to register with their call server, and you should be able to make and receive calls at the same number as the Handytone ATA, providing TalkIt will allow multiple registrations to the same account.
    Secondly, you can contact TalkIt, and explain that you wish to have them provide you an additional ATA configured with the same users / phone numbers as your current unit. Some providers are less prone to provide you with the information required to configure your own device, but they may be open to you purchasing / renting an additional unit that they provide, and configuring it in such a way that it shares the same number as the original ATA device they provided you with.
    Thirdly, you can purchase a SIP Gateway device, such as the SPA3102, which would provide an FXO port which you could connect to the FXS port of the Handytone ATA device, and then configure one of your SPA112's to make an IP connection to the SPA3102, and connect an analogue line to that SPA112.
    If you're not overly familliar with IP Telephony, I'd probably recommend getting a second ATA from TalkIt, as it would come preconfigured, and you would only have to plug it in for it to work. If they're willing to provide you with the SIP information, you may be able to configure one of the SPA112's that you already have, and just use that to connect to their service. This would probably be the least expensive option, but would require you to perform the configuration of the additional ATA device yourself. The third option, which most closely resembles your initial request, would not involve TalkIt, however it would involve purchasing the additional SIP Gateway device, as well as perform all of the configuration yourself. I, personally, have not configured a SIP Gateway device before, so I don't know exactly how involved that configuration is. Configuring the SPA112 shouldn't be too bad, but again, I've never configured it in exactly the way you're describing, so I can't say for sure. I've only ever used them to connect to a full IP PBX, or else a Hosted service, similar to the TalkIT provided Handytone unit.
    Hope this provides a little direction, and wasn't too confusing.
    Randy

  • Help required : Back to back printing for line items.......

    I have a critical requirement:
    Mulitple Handling units are to be printed, with every new handling unit to be printed on a new page and if the line items for a particular handling unit exceeds the page then it should be printed back to back.... PLease help it very urgent. points will be rewarded.....

    go to basic settings an select print mode as "D" means duplex printing..now you will get back top back printing.

  • When I try to use spellcheck, I get the "Cannot find the User dictionary". It has always worked in the past and when I go to choose the main dictionary, it just goes back to the same line, cannot find user dictionary.

    When I try to use spellcheck, I get the "Cannot find the User dictionary". It has always worked in the past and when I go to choose the main dictionary, it just goes back to the same line, cannot find user dictionary.

    Have you ever created a user dictionary? You have to manually create one, AppleWorks won't do for you. The user dictionary & any other dictionaries belong in the AppleWorks Essentials folder which belongs in the AppleWorks 6 folder in Applications.
    Deleting & reinstalling AppleWorks from the original disk will not delete your files unless you have saved them in the application folder. The Mac OS creates a separate Documents folder for your files & that is where the documents you created should be.
    Unless all of your documents are AppleWorks 6 word processing documents, Pages alone is not sufficient. The iWork applications - Keynote, Pages & Numbers - can only open AppleWorks 6 presentation, word processing & spreadsheet documents, respectively. They will not open any other type of AppleWorks 6 files or any AppleWorks 5 or any version of ClarisWorks files.

  • I have a photosmart plus b210 e print and when I print with a black back ground I get lines

    I have a photosmart plus b210 e print and when I print  with a black back ground I get lines.  What can I do to eliminate the
    lines in the photo
    Thank You

    Hey appollus,
    Do you get these lines only when printing with ePrint? If not, it sounds like a printhead issue. Here are the steps to fix the issue.
    1. Go to the setup menu on the printers front screen.
    2. Go to tools.
    3. Go to clean printhead
    You may need to do this a few times to completely remove the lines in the print.
    Although I am an HP employee, I am speaking for myself and not for HP.
    If I have resolved your issue, feel free to provide Kudos and make sure you mark this thread as solution provided.

  • Can anyone knows how to fix back camera having pink lines when i use it so please help me  thank you

    can anyone knows how to fix back camera having pink lines when i use it so please help me  thank you
    <Email Edited by Host>

    You're welcome.
    The 6.1.4 update had nothing to do with this. If it did, then every iPhone with 6.1.4 installed would have the same problem.
    Apple doesn't support downgrading the firmware, which won't change anything.
    If an Apple Store is miles away, then call AppleCare.

  • Issues with play back in the time line

    I am having issues with play back in the time line.
    am working with footage captured off a DVCAM Tape in a DV/DVCPRO NTSC Time line.
    My settings are set to match the source footage so I dont have to render. What ends up happening is the footage at times plays fine and smooth and then out of no where it will start playing choppy. like its lagging. But the Audio stay fine. I use to have to problem before but then it stopped.
    Now its back and I can not figure out why it does this. Usually a restart of the system would help solve it but now it still keeps coming back.
    i have tried different settings in the RT menu and still seem to be having the same problem.
    i am running the footage of 3 1TB drives in Raid0 and the System has 16GB of Ram. So I dont see this being the issue.
    any ideas?

    of course not, the system boots from a 320GB Western Digital Hard Drive. (the one that came with the system)
    I have a feeling that its not the Hard Drive, but no idea what it could be.

  • Is there any way in Mavericks to go back to the old "line label" color strips instead of the new mini dots, which are virtually worthless they are so small and faint.

    Is there any way in Mavericks to go back to the "full line" color label as opposed to the mini dots, which are too small and faint and virtually worthless?

    Unfortunately, not.
    You can file feedback here. The more who file the more chance it will get done.

  • Sales Order Line in Back to Back stuck in PO-ReqCreated Status

    Hi
    I am running a Sales Order Back to Back Cycle. The status of SO Line Remains in PO-ReqCreated inspite of the PO linked to Sales order line is created, approved and receipt is done. Due to this the line is released for shipping ; WF mailer is up and running.
    Has anyone experienced this in the project , pl let me know the resolution.
    We are on 11.5.10.2.
    Thanks

    Hello,
    Check the similar note in metalink
    Cannot Progress Sales Order Since Order Line is Stuck In PO-ReqRequested Status CTOPROCB.pls [ID 411955.1]
    I suggest you to followup with Oracle Dev team thru SR.
    Thanks
    -Arif.

  • SPA-3102s back-to-back

    Hello, we are trying to use two spa-3102 boxes in a back to back configuration to provide phone lines to a construction site (via a Cisco wireless bridge) like this:
    (PSTN)--(SPA3102 FXO PORT)--(Wireless Bridge)--(SPA3102 FXS PORT)--(Phone/Fax)
    We have voice calls passing correctly in both directions, and the phone/fax machine at the construction site is able to receive faxes most of the time, but they are unable to send outgoing faxes. When the fax machine attempts to dial, you can hear the machine pick up, dial the number, and then there is a few moments of silence followed by a fast busy signal. Any ideas?
    Thanks!

    EvilFetus wrote:
    When the fax machine attempts to dial, you can hear the machine pick up, dial the number, and then there is a few moments of silence followed by a fast busy signal. Any ideas?
    Thanks!
    If the dialing waits until the interdigit timeout and then gives a fast busy it usually means that the digits dialed are not correct. If the dialing is "back-to-back" as you say, you probably are dialing some code that sends a sip uri for direct ip dialing. There are a number of variables involved.
    You should be able to view the last dialed number on the INFO tab.

  • Telephone line

    Hello i have been experienceing troubles with both my internet and phone line for a couple of years now. I have contacted support by phone a number of times but they keep telling me to go to my computer and theres a problem with the router, but i have already been through that. A new router was sent to me by the company and connects to all my devices with full bars but i am experiencing rapid loss of connection and sometimes large amount of static in the phone lines. I have been told to get a booster so the connection isnt lost and it would be more stable so i bought a ethernet cable. The cable works great but i am still experienceing connection trouble everything is set up fine but often i still lose connection rapidly and internet is extremly slow. I went outside and notice the telephone line has wires hanging from the box and ice built up inside the wire harneses. A man was sent up to fix this line from the company about 2 years ago when a tree fell down on it during a storm but all he did was push the wires back in the black box and ducktaped a trash back to hold the wires in and said he will be back to finish but never was. Now the trash bag is of the wires and the live wires are all scattered over the woods below my house. I fear this is a fire hazzard and the company did not take this problem to seriously. I asked support if they could send someone up but they said they wont unless i pay them to fix it! I am not shure what to do at this point i feel that i was paitent enough with the company but they do not seem to care or be very realiable at this point, was thinking about switch to atlantic but not shure all i want is the lines to be fixed. 

    Your issue has been escalated to a Verizon agent. Before the agent can begin assisting you, they will need to collect further information from you.Please go to your profile page for the forum, and look in the middle, right at the top where you will find an area titled "My Support Cases". You can reach your profile page by clicking on your name beside your post, or at the top left of this page underneath the title of the board.
    Under “My Support Cases” you will find a link to the private board where you and the agent may exchange information. This should be checked on a frequent basis as the agent may be waiting for information from you before they can proceed with any actions. To ensure you know when they have responded to you, at the top of your support case there is a drop down menu for support case options. Open that and choose "subscribe".
    Please keep all correspondence regarding your issue in the private support portal.

  • How to find Requisition number of a closed Back-to-back Order

    For a closed back-to-back order line how to find the requisition number?
    Tried using the "Requisition Summary" form --> Related Documents(Tab) --> providing the Sales order number.
    But the LOV attached to sales order does not contain the B2B sales order number.
    Hence not able to find the corresponding requisition.
    Regards
    Edited by: 839781 on Dec 1, 2011 2:25 AM

    Are sure it was a B2B sales order?
    Does the item placed in the order is ATO enabled?
    I can find the requistion of the closed B2B order line from the requistions summary window
    only order line is closed..header is still open for me
    Thanks
    Mahendra

  • UCMA 4 and back to backing a file transfer request

    OK, I know that file transfer isn't technically supported on UCMA 4.0, but I wanted to take another look at it and see whether there was a way to b2b a file transfer request. After all, there's no reason that it shouldn't work if the messaging is correct,
    right? The scenario I have is A <-b2b-> app <-b2b->B.  I have an IM conversation going on between A and B, so now I'm trying to set it up so that A can send a file to B. 
    So far I've extended the platform to accept file transfer requests by creating my own call and factory classes, and then registering them using RegisterPlatformExtension.  This means that when A sends a file, the INVITE gets delivered to my application. 
    Now I'm taking that INVITE and creating a new b2b call.  A file transfer request looks something like this:
    TL_INFO(TF_PROTOCOL) [0]16A8.4B28::02/10/2015-19:53:05.007.001d492f (SIPStack,SIPAdminLog::ProtocolRecord::Flush:ProtocolRecord.cpp(265))[3939761282] $$begin_record
    Trace-Correlation-Id: 3939761282
    Instance-Id: FDB3
    Direction: incoming
    Peer: 10.0.154.20:49282
    Message-Type: request
    Start-Line: INVITE sip:[email protected] SIP/2.0
    From: <sip:[email protected]>;tag=eafd3e699d;epid=ccd5657cac
    To: <sip:[email protected]>
    Call-ID: 0acf0330423241258576d7c5cc42aa01
    CSeq: 1 INVITE
    Contact: <sip:[email protected];opaque=user:epid:d2lIs-103l2YSpDwCSajtAAA;gruu>
    Via: SIP/2.0/TLS 10.0.154.20:49282
    Max-Forwards: 70
    Content-Length: 1920
    Content-Type: multipart/mixed;boundary="----=_NextPart_000_0026_01D04541.4641C2D0"
    Message-Body:
    ------=_NextPart_000_0026_01D04541.4641C2D0
    Content-Type: application/sdp
    Content-Transfer-Encoding: 7bit
    Content-ID: <[email protected]>
    Content-Dis; handling=optional; ms-proxy-2007fallback
    v=0
    o=- 0 0 IN IP4 192.168.200.71
    s=session
    c=IN IP4 192.168.200.71
    b=CT:99980
    t=0 0
    m=data 21300 TCP/RTP/SAVP 127
    a=ice-ufrag:lYAu
    a=ice-pwd:y0gkW4r9zGSW6E2VdtMprlEh
    a=candidate:1 1 TCP-PASS 2120613887 192.168.200.71 10856 typ host
    a=candidate:1 2 TCP-PASS 2120613374 192.168.200.71 10856 typ host
    a=candidate:2 1 TCP-ACT 2121006591 192.168.200.71 21300 typ host
    a=candidate:2 2 TCP-ACT 2121006078 192.168.200.71 21300 typ host
    a=candidate:3 1 TCP-PASS 2120612863 10.0.154.20 31624 typ host
    a=candidate:3 2 TCP-PASS 2120612350 10.0.154.20 31624 typ host
    a=candidate:4 1 TCP-ACT 2121005567 10.0.154.20 3921 typ host
    a=candidate:4 2 TCP-ACT 2121005054 10.0.154.20 3921 typ host
    a=cryptoscale:1 client AES_CM_128_HMAC_SHA1_80 inline:4CZbzYM/GYDbygj8JwMTodKo85C4Xx7TMzeMIuBU|2^31|1:1
    a=crypto:2 AES_CM_128_HMAC_SHA1_80 inline:Ohlo65gDsUvxCF39A382Rl4vGL+SG9R/lUEYU/br|2^31|1:1
    a=crypto:3 AES_CM_128_HMAC_SHA1_80 inline:EZ7Zm3K0H/WW5K49LAk9/C0T8x8nhkumJOycSek7|2^31
    a=setup:active
    a=connection:new
    a=rtcp:21300
    a=mid:1
    a=sendonly
    a=rtpmap:127 x-data/90000
    ------=_NextPart_000_0026_01D04541.4641C2D0
    Content-Type: application/ms-filetransfer+xml
    Content-Transfer-Encoding: quoted-printable
    Content-ID: <[email protected]>
    Content-Dis; handling=optional
    <request xmlns=3D"http://schemas.microsoft.com/rtc/2009/05/filetransfer" =
    requestId=3D"13">
    <publishFile>
    <fileInfo embedded=3D"true">
    <id>{67190A30-C59F-480D-96DD-5F3941C39C49}</id>
    <name>dbchange.log</name>
    <size>3609</size>
    </fileInfo>
    </publishFile>
    </request>
    ------=_NextPart_000_0026_01D04541.4641C2D0--
    $$end_record
    I've got my b2bed invite looking almost identical to the original invite by creating a custom MIME type on the CallEstablishOptions for the back to back call using something like this:
    Regex r = new Regex(@"^((.|\n)*)(\<request)((.|\n)*)(request\>)((.|\n)*)$");
    Match m=r.Match(args.RequestData.GetMessageBodyString());
    content=string.Format("Content-Transfer-Encoding: quoted-printable\r\n{0}{1}{2}",m.Groups[3],m.Groups[4],m.Groups[6]);
    opt.CustomMimeParts.Add(new MimePartContentDescription(new ContentType("application/ms-filetransfer+xml"),System.Text.ASCIIEncoding.UTF8.GetBytes(content)));
    opt.CustomMimeParts[0].ContentDispositionHeader = new SignalingHeader("Content-Disposition", "render; handling=optional");
    So far the only differences I can see in my outbound message vs the original SDP are that the Content-Transfer-Encoding might not be seen as a header (since the SignalingHeaders property on the MimePartContentDescription is read only), and the Content-Transfer-Encoding
    on the first MIME part (created by the BackToBackCall) is missing (even though I specified it on the PassThroughHeaders).  Even with all of this though, I still get a 488 on client B when I attempt the transfer (even though the invite goes through). 
    What I'm wondering though, is whether there's any way at all to get this working the way I'd expect, where a file gets transferred directly between A and B, without my bot having to receive it first.  The other approach I've looked at is binding my
    own media provider class to customize the SDP, but if this MIME part approach isn't going to work, then I have a feeling the media provider won't work either. 
    Any suggestions on where to look next? 
    Thanks!
    Chris

    Chris,
    I am trying to do something similar to this and from what I have read and in talking to MS is that you need to extend the Call and Flow class which it looks like you have been able to do. Could I bother you to share what you have written? Maybe we can help
    each other out on this. I am basically trying to create an application that will be able to capture a file transfer and save it, then send the original request on to the intended recipient.
    Thanks in advance,
    Anthony

  • Back-to-Back PO from Sales Order

    On Sap B1 2005 when we made a Back-to-Back PO's from Sales Orders the Sales Order information stayed on the screen in the background and was very handy when doing a multiple line items as we put the list prices on non-printable text lines for future reference.
    Now with 2007 the sales order information disappears and the only way to keep the information on the screen is to save the order without ticking the PO check box, then re-open it and then tick the PO check box.
    Why would SAP do this?

    You would better post it on this forum for SAP development team to know:
    /community [original link is broken]
    Thanks,
    Gordon

  • Copy Customer Ref No to Vendor Ref No when create back to back Order

    Hi,
    I would like to copy Customer Ref No to Vendor Ref No when create back to back Sales Order to Purchase Order.  Please suggest a way.
    Does i need to do before form add?
    If BusinessObjectInfo.FormTypeEx = "65" And BusinessObjectInfo.BeforeAction = True Then
    End If
    Please help!
    Regards,
    Anna

    Hello Anna,
    You should update purchase order (copy the customer no ref to the vendor ref) after action (pVal = false), see the sample code here.
    Private Sub FormDataEventHandler( _
        ByRef BusinessObjectInfo As SAPbouiCOM.BusinessObjectInfo, _
        ByRef BubbleEvent As Boolean) Handles oApp.FormDataEvent
            'Before action = true, start the transation
            If BusinessObjectInfo.FormTypeEx = "65" _
                    And (BusinessObjectInfo.EventType = SAPbouiCOM.BoEventTypes.et_FORM_DATA_ADD) _
                    And BusinessObjectInfo.BeforeAction = True Then
                oCompany.StartTransaction()
            End If
            'Before Action = false,
            'Update purchase order
            'Succeed, commit, otherwise rollback
            If BusinessObjectInfo.FormTypeEx = "65" _
            And (BusinessObjectInfo.EventType = SAPbouiCOM.BoEventTypes.et_FORM_DATA_ADD ) Then
                If BusinessObjectInfo.BeforeAction = False And BusinessObjectInfo.ActionSuccess Then
                    Dim objectKey As String = String.Empty
                    'Get the purchase order key added right now
                    oCompany.GetNewObjectCode(objectKey)
                    Dim oPurchaseOrder As SAPbobsCOM.Documents = Nothing
                    oPurchaseOrder = oCompany.GetBusinessObject(SAPbobsCOM.BoObjectTypes.oPurchaseOrders)
                    If oPurchaseOrder.GetByKey(CInt(objectKey)) Then
                        Dim oLines As SAPbobsCOM.Document_Lines = oPurchaseOrder.Lines
                        Dim salseOrderNum As String = oLines.BaseEntry
                        'add you code to get the custoemr ref of the sales order and set it the purchase order
                        lRetCode = oPurchaseOrder.Update
                        If lRetCode = 0 Then
                            'update the production tree succesfully,
                            oCompany.EndTransaction(SAPbobsCOM.BoWfTransOpt.wf_Commit)
                        Else
                            oCompany.EndTransaction(SAPbobsCOM.BoWfTransOpt.wf_RollBack)
                        End If
                    End If
                End If
            End If
        End Sub
    Kind Regards
    -Yatsea

Maybe you are looking for