SPA3102 pstn-voip dial tone without entering pin

Hello,
Once spa3102 is authenticated by pin, the adapter gives dial tone without entering pin (just the # sign after the beep) even when a different phone is used to call the spa3102 pstn number.
Isn't this a security compromise? Any one can access my voip account if the pin does not work.
Any help will be greatly appreciated.

that's weird...if PIN Authentication is enabled, it prompts the caller to enter the PIN number followed by a # key
how long is your PIN? i have the same set-up in my house and authentication works fine and i tried pressing # after the beeps but it didn't give me a dial tone....
| isolate! isolate! isolate! |

Similar Messages

SPA3102 In VOIP and out PSTN dialed

I want to call my SPA3102 on my VOIP connection, then I want to get a dial tone for my landline and be able to dial out on it to a number I enter. How do I configure the 3102 to do this?
Thanks

Phantom, have you been able to configure this?
Please can someone respond or point me to an answer, I am searching hard...
I need to achieve the same mentioned above, need to get the Dial tone of the PSTN when I dial into SPA3102 using VOIP.
Please help... Thanks.

Panasonic PBX Dial Tone with SPA3102

I have successfully configured two SPA3102 to deliver remote dial tone.
(CO Line)----[SPA3102]===={IP Network}====[SPA3102]----Telephone
Works fine calls in or out using dial tone from a Rhino Channelbank.
This does not work so well
(Panasonic PBX Analog Extension Port)----[SPA3102}===={IP Network}====[SPA3102]----(CO Line)---->>PBX CO Port
I can call from another ext. in the PBX to the analog phone and it work, but it will not grab the line to make the call from the Remote ATA, or the local ATA. Has anyone dealt with this or a similar issue?
Thanks, Damon

Damon:
The problem lies on the voltage. Go to Voice/Info and check at PSTN Line Status the Line Voltage on hook, then off hook. (In my case with a 308 it was -26 and -6) and then put the number between those (in my case, -16) in Voice/PSTN Line at International Control, Line-In-Use Voltage
Best regards,
Rick

An incoming call from VoIP. The SPA122 generate Dial Tone after the far end hung up rather busy tone.

Hi All!
I have a problem with the SPA122 telephony adapter, uncorrectly process the subscriber signaling at the end of the call.
1) Outbound call from FXS port SPA122 . When a remote caller hangs up first , the subscriber SPA122 Reorder Tone played with a delay specified in the Reorder Delay. This circuit is working properly.
2 ) Incoming call from VoIP to the SPA122. When a remote caller hangs up first , subscriber on the FXS port of the SPA122 hears silence ~ 3-4 seconds , then SPA122 plays Dial Tone, as if he had just picked up the phone and he 's going to call . No signal lights out (Busy Tone or Reorder Tone) will not play .
Config is attached.
Model: SPA122, LAN, 2 FXS
Hardware Version: 1.0.0 Boot Version: 1.0.1 (Oct 6 2011 - 20:04:00)
Firmware Version: 1.3.2-XU (014) Jul 2 2013
Recovery Firmware: 1.0.2 (001)
WAN MAC Address: 6C:20:56:55:3A:B6
Host Name: SPA122
Domain Name: (none)
Serial Number: CCQ16450LG3
However, other VoIP terminals registered to Huawei, including older versions of the Linksys SPA2102 work in these scenarios correctly.
Where to kick it?

[2] is misconfiguration on your's side. You have CPC turned on, but no CPC capable device. Set CPC Duration to zero to turn off CPC.
By the way, wrong forum for your question. You should consider to move it to space.

VoIP - Second Dial Tone

Hi,
Any specific commands to generate asecond dial tone on Cisco Multi- Service routers.
Scenario is as follows :
PSTN ---Router at location A--Router at Location B--- Router Location C --Closed User Group.
Users are provided with the PSTN no which they dialin. Through Router A at location Ait is switched to Service Provider cloud and reaches Router B at location B which inturn is back to back connected with another router for CUG Connectivity.
When users dial the PSTN no after the intial tone, users keys in the CUG No.
Any possibility to differentiate the second tone with different ring and tone in the routers?
thanks
Sundara

Hi Sundara ,
I dont think this can be achieved. When user at SITE A gets the dial tone, he is getting from the PSTN A. So the dial tone cannot be modified.
Again, when the user gets the secondary dialtone, who is generating it. Is it the PSTN B ?
Thanks
Venky

Can I turn off my dial tone clicks without silencing my phone?

I Need to be able to silence my phone dial keypad without silencing my ringer.
Please fix this issue

This is not a place that you can contact apple unfortunatley... If you want Apple to hear your complaint you would want to go to Apple.com/feedback This is actually a common problem that many people are complaining about so please submitt feedback! It really helps.

3rd week without a merged account, 5 days without dial tone

On Sept 26th, i added TV and PHONE to my internet account that i already had for two years
Verizon created the order and provisioned me with a temporary number until my phone number port from vonage came through.
ONT Line 1 was activated with the temporary number.
Weeks later i call and Verizon said that they needed to re-create the number port order from vonage, this time the rep said that i needed to create a type of order called a WINBACK phone number order. I explicitly said that they needed to make sure that the services need to come under ONE account for the triple play discounts, and for the additional features.
3 days later, number port came through from vonage, activated on ONT Line 2. The line had a whole new account number, and couldnt be seen on My Verizon, and also couldnt be seen on my TVs
I subsequently cancelled Line 1 so i wont be double billed
I called in to verizon to have them merge accounts, and this is where the whole saga began
Call verizon to merge accounts, they create ROC ticket
3 days later no change, call verizon again, they claim ROC ticket wasnt created originally. Will create new one.
3 days later no change, call verizon again, they claim that the ROC ticket was completed..
Techs escalated me to "Sales and orders" and got a lady in the 636 area code. Rep said that Digital Voice lines could NOT be merged in with TV and Internet accounts, and that in order to "fix" the problem, she said that i needed to "cancel" the ported Line 2 number for a "day" while it purged through the system, and can be added to my primary account number. All the while she was saying that the original rep doing the WINBACK did it completely wrong and f-ed everything up. All the while she was trying to upsell me on the internet and service bundle, and trying to give me HBO and SHOWTIME on a trail basis. **bleep**. I dont need stinking channels. I just wnat my accounts merged.
As promised, she cancled my Line 2 account, and when dialing that number, for a day, i got a "number was disconnected" message. Also as promised, a day later, i got straight to voicemail on that number. So i knew that number was activated.
I STILL DONT HAVE DIALTONE, AND PHONE GOES TO VOICEMAIL ON 1 RING.Swaped lines 1 / lines 2 on the ONT. No change. SOmething is wrong with verizon's end. This was 10/21/2011
10/24 (yesterday) a tech shows up and leaves, telling me that the order was "stuck in IVAPP" and i needed to call sales. Around the same time he was here, i got an email on my phone saying "service ticket has been closed" and the dreaded email FiOS Revised Installation Appointment
10/31 is the revised date. At this point i am
What do i need to do to get a working dial tone on my line? This is becomming a safety issue as i do not have good (verizon) mobile coverage here, and also a big business liability for me as i use that number on my business cards for clients to call.
So far i have spoken to
Fios Solutions Center
Fios Elite
Fios Order Support Group
Fios Sales
Fios Sales Manager
I need this order expedited and escalated immediately or else i have no choice but to call the PUC to complain about this. Seems like one hand doesent know what the other limbs are doing.

I'm sorry you are having difficulty. An agent with access to your account will reach out to you directly by email, private message in the Forums and/or the billing telephone number on your Verizon account for more information or to help you resolve your issue.
ephatcow wrote:
Called Fios Elite, spoke to Jessica. After Jessica talked to her WINBACK department, she came back saying the system would not allow them to do anything with the order since it was pending. The reason why im calling is clearly BECAUSE the order was pending! grrrrrrrr
I aksed her about a credit to my account due to these problems, and again, she said that the "system that issues credits is down"
Why am i being held hostage to VZ's "system". THis is BEYOND frustrating.
6th day, no dialtone.

SPA3102 PSTN problem

I am using spa3102 which have Line port and PSTN port
I have no problem with line.... But I configured the PSTN port with 8 accounts and I enabled
The PSTN Caller Auth Method: PIN under PSTN-To-VoIP Gateway Setup and I configured
8 pin for each account, Normally when I call PSTN and I hear the beep tone I enter My Pin followed by # sign and it work fine...But if I called again and I put only # sign without any pin
Spa3102 open the last pin number was making a call
So maybe there is an option I must do or it is some bugs with the firmware
Note that my spa3102 have the latest upgrade
Regards
Wael Saad
00965-9618253

It's not broken. The problem is was with the cable used to connect it to the UK British Telecom wall socket. I did not use the grey cable that came with it, but used a UK phone cord I had lying around - bad move.
When talking to Linuxemporium, from where I bought the SPA3102, I was made aware that the cable might the problem. So I went over the road to a small phone shop to get a US-UK adapter (the cable packed with the SPA3102 is still a US cable), which didn't solve it. I got another adapter from a well known UK electronics retailer, and that one solved the problem. The SPA3102 is now happily working as my PSTN gateway.
I hope this can help others having similar problems.

Looking for App to dial phone number and pin to check voice mail?

When I am checking my office voice mail remotely with my 3G iphone, I can go to favorites or contacts and dial my office phone number. But then I have to manually dial my office number plus #, then wait 4 seconds and dial my pin plus #. Also, I have to touch "Speaker" or the office voice mail will not hearing the touch tones.
Is there an app that will dial the office number plus #, wait 4 seconds, then dial the pin plus # by pressing just one button? My treo had a dial feature that would dial my office voice mail number, pause 1 second per entered comma, plus pin by pushing only one button. Also, how do I make the office voice mail hear the touch tones without using speaker?

Well you can enter pauses as well with the iPhone in your contact list saved number. As for the voice mail service not getting your key entries unless on speaker, not sure.

Bt hub phone - no dial tone

Hi,
just swapped my old home hub 1 for a HH2. Setup BBtalk with the online configurarion tool.
The BBtalk light on the hub is blue, and I can receive calls OK. However I cannot get a dial tone on the hub phone. It is an old 1020 hub phone, but I know many people have these working OK with a HH2. All used to be OK with my old hub.
I have tried deleting the service from the hub, and resetting, and also resetting the phone, but so far no joy.
Any suggestions?
Cheers

You will need to ensure you have registered the phone to the hub, check out details from jarviser's web site.
http://www.jarviser.co.uk/jarviser/howto3.html#type4
If you have 1010 or 1020 hubphones from V1 or V1.5 hubs you can use them on a V2 hub for basic calls with reasonable call quality, but no fancy features. This is covered in the BT online help but there are a few additional action that should help.
First de-register the handset back to factory settings. On the handset take a look at which button is the "Menu" button.
Take off the battery cover and remove one battery.
Hold in the Menu button while reinserting the battery.
After a few seconds the display will show "TEST MODE"
Do NOT press OK, but press "5"
The display will change to show "CLEAR SUB"
Hit OK and the handset will deregister, but the phone book will be retained.
The handset will now say "Please register the handset to the BT Homehub"
Do NOT press OK! - Press the Back (RH) button
Press Menu (LH) button
Register Handset should be highlighted so click on OK
Select Base 1 unless it has an asterisk next to it, in which case select the next free base then hit OK.
The handset asks you to put the Home Hub into registration mode by pressing the Wireless association key on the side of your Hub version for three seconds.
Actually 3 seconds is not required on the V2 hub, simply press it briefly, then when the light is flashing Hit OK on the phone.
Handset then says System Pin - enter 0000 and hit OK
Handset says registering Handset Please Wait, or similar.
The handset will say 'Handset registered' when successfully registered.
Now reboot the phone handset by removing a battery again, count 5 and re-insert the battery without pressing any buttons this time.
The above actions should leave the best available sound quality, but you will not get Hi-Ds sound when you call another hubphone user.
You will be able to use the intercom between two old type hub phones, and can call a 2.1 phone from an old phone, but the 2.1 phone will not call an old hub phone 1010 on intercom.
(If I have helped you in any way to say "Thank You" please click on the star next to the message. Thank You)
If I have solved your Issue please click the "Mark as accepted solution" button.

How can I make the E7 to produce dial-tones when c...

Of course, I can hear the DTMF dial tones when I dial the number from the touch screen.
But, I need the E7 to send dial tones when I call a contact (hence I don't dial from the touch screen). I need that because I'm using a calling card which needs the dial tones to be sent.
It works like this:
In the contact details I enter a long number, with pauses, like:
18001231234p09876543p011392109876
where the 1st numer calls the calling-card number, the 2nd is the pin, the 3rd is the international number I'm calling.
Of corse, when I call that long number (which is a contact) the carrier needs to "hear" the dial tones.
Hence, the question in the subject line.
P.S. If there is a better way to use calling cards, pls let me know.

I think I was wrong. After trial and re-trials I see the E7 actually sends out the dial tones.
Well, I don't know why it did not work at first. Now it's ok.

Qosimo F20 - try to make WLAN connection - no dial tone

Hi,
I am having trouble connecting through my wireless router D-Link my PC say that wireless is connected with excellent signal but when I try to connect it tells me thereis no dial tone.
If I plug in the speedtouch modem I can connect immediately, any suggestions

Hi,
if I understand you right, the problem is not the wireless connection, but the connection from the router to the internet.
To check if your wireless connection is ok, try to enter the setup of your router without a cable connected. If this works, the problem is not in your notebook.
In the router setup you have to establish the internet connection. The way this is done should be described in your router manual. I don't have a D-Link router, so I also don't know this setup, sorry.
Bye

No Broadband, No Dial Tone!??

My broadband went down on Friday. I rang the number that comes up on the browser, BT has done tests on the line and there is no dial tone either so I'm without phone as well! Their estimated date for fixing this is 23:59 on Wednesday!!
Does anyone know what the problem is?? It seems all the other houses around my area are fine? Living in a student house, the seven of us are in constant need of the web for our studies so this is very annoying.
Our contract with Bt started at the end of September and this is the second problem we've had. It took over a month for our speeds to be increased so that they were in the acceptable range given on the BT speed test. Before this the broadband was basically unusable.
Getting really fed up with the service (or lack of). And hope that i can be compensated for this!!
If anyone could shed some light on what the problem is at the moment that would at least give house mate and I some peace of mind. Seems very unfair that we should have to pay full price for line rental and broadband when it looks like we wont be getting either of those services for 6 days!

If there's no dial tone then there is probably a cable fault of some kind . . . not uncommon when the weather is bad and large quantities of corrosive salt are in use on roads and pavements. The dissolved salt will find its way into any weakness in cabling and can cause the sort of problem you have.
Its normal for BT to give credit for times when there is no connection. Make a note of the exact dates and times when there was no service and then contact BT for a credit on your bill.

The phone does not lock up when entering PIN code

This morning my Z1 Compact wanted me to enter the PIN code: I did so but the only thing that happened was that the text "Enter PIN code" disappeared. But I was still at the same page. It seems to have stuck or freezed. Tried to remove and reset the SIM card, called the operator who says there´s nothing wrong with the SIM card. tried to force restart with and without the SIM card. I can't get pass that starting page.
The funny thing is that on the "mssage board" or whatever it is called at the top of the phone is updating when I got a message, mail, updates etc. But I can not scroll down and see them in detail.

You may want to consider running a software repair
Fully switch off your phone and make sure it is disconnected from your Pc then start PC Compannion and select Support zone then Update my phone/tablet then in Blue select Repair my phone /tablet and follow the onscreen instructions and when prompted making sure your phone is still switched off hold Volume down and connect your USB cable which should enter your phone into flashmode and start the repair process
For a successful technology, reality must take precedence over public relations, for Nature cannot be fooled. Richard P. Feynman

I lost tons of metadata (pin/map locations for places visited). it just disappeared after days of work. any ideas on recovery?

I lost tons of metadata (pin/map locations for places visited) on aperture after days of work entering it (over 400 locations visited). any ideas how to recover it? i can't find it anywhere.

What happened before the data were lost? Did Aperture crash?

SPA3102 pstn-voip dial tone without entering pin

Similar Messages

Maybe you are looking for