SRW224G4P uplink to catalyst 3560 switch trunk

I have many SRW224g4p switchs,and I use a catalyst 3560  for a core switch.
The SRW224g4p uplink to 3560 switch
What can I config the port of the 3560 to SRW224g4p(Their are many of vlans in my network)
and config the port of SRW224g4p to 3560's port
ps:config trunk port problem

Hi Wei,
     Are you working on the Linksys SRW224G4P or the replacement Cisco (300 Series) SRW224G4P-K9-NA? Can you attach your 3560 Truk Port Configuration along with the VLAN Configuration?
Thanks,
Kevin

Similar Messages

  • Documentation About catalyst 3560 switches

    Hi,
    Any one have documentation about 3560 switches, that includes features & configuration cababiities,
    thanks,

    Hi,
    There is lot of documents available in Product support. One link is,
    http://www.cisco.com/en/US/products/hw/switches/ps5528/tsd_products_support_series_home.html
    Rate if it does,
    Rgs

  • Cascade Catalyst 3560 switch for loaded traffic

    I have a layer 3 Catalyst switch 3560 with 24 FE interfaces.
    I need to pump traffic from traffic generator into port 1 and propagate it to other ports; the last port will be connected back to the traffic generator.
    I suppose that I need to cascade some of the switchports but how do I configure the catalyst switch for this setup? Is it making use of routed port and static routing?

    Hi Ankur,
    Thanks for the reply.
    The traffic generator are layer 3 interfaces which I can assign IP address.
    You mentioned that I do not need any routing, but I require traffic coming from the traffic generator(e.g FE1) going into switchport 1 to traverse through the rest of the switchports before exiting from the last switchport back to the traffic generator(e.g FE2). Therefore, I need advice on how to setup the catalyst switch to achieve this.If I assign ip address for this traffic to end at the traffic generator-FE2, the generated traffic will enter the switch at switchport 1 and directly exit from the last switchport without any traversing done. Btw, do I need to cascade my switch with cross cable in this aspect?
    Thanks in advance for your advice.
    Regards,
    Raymond

  • Limit bandwidth per user/computer using Catalyst 3560 switch

    Hi -
    Can someone help me getting started (if at all possible...) with enabling controll of used bandwidth at a "per-user"-level.
    I wonder if it possible to do this dynamicly with respect to the overall demand from other users.
    I've searching a lot, but I'm missing the terminology :) 
    Sincerly
    Nicholas

    Disclaimer
    The Author of this posting offers the information contained within this posting without consideration and with the reader's understanding that there's no implied or expressed suitability or fitness for any purpose. Information provided is for informational purposes only and should not be construed as rendering professional advice of any kind. Usage of this posting's information is solely at reader's own risk.
    Liability Disclaimer
    In no event shall Author be liable for any damages whatsoever (including, without limitation, damages for loss of use, data or profit) arising out of the use or inability to use the posting's information even if Author has been advised of the possibility of such damage.
    Posting
    To my knowledge, what you want to accomplish isn't possible on a 3560.
    You can police at ingress, and if you use a policy map, you can police different "known" IPs.
    What you could do, is police user ports ingress at some nomimal bandwidth, and if exceeded, mark the packets.  Then on egress, you could direct those packets to an different egress queue with a lower bandwidth guarantee than the normal queue.

  • Dynamic VLANs on a Catalyst 3560

    Hello,
    I'm looking for a solution that would enable me to assign users to a specific VLAN based on MAC address. I'm using a Catalyst 3560 switch. Is there something similar to VMPS that would allow me to do this? I would like to run VMPS, but it looks like you need a VMPS server (catalyst 5000) to do this. Any help would be appreciated. Thanks!

    They can be is the answer; however they don't have to be. Not all Cisco IP Phones have an 802.1x Supplicant (I assume you are using Cisco IP Phones and Voice VLANs?), only the newer ones do I think (7941, 7961, 7970 etc). I think by default the Voice VLAN on the access port does not do 802.1x authentication so the Phones bypass any 802.1x authentication.
    If you have non-Cisco IP Phones then there are some more hurdles like VLAN detection and depending on the Vendor this can be achieved in a number of ways. It's should all be possible though.
    Andy

  • CISCO CATALYST 3560 SFP INTERCONNECT CABLE

    What is the advantage of using this SFP cable over a 1000BaseT GBIC and daisy chaining the switches together?
    Just curious???
    Thanks!

    The advantage comes down to cost. Whether you can realize this advantage depends on the distance between the two Catalyst 3560 switches.
    If the distance is less than or equal to 50cm, then one SFP Interconnect Cable (CAB-SFP-50CM=) at US$250 is a much less expensive way to connect the two switches than two 1000BASE-T SFP (GLC-T=) at US$395 each = US$790 plus a Cat5 or better UTP Gigabit Ethernet crossover cable.
    If the distance is greater than 50cm but less than or equal to 100m, then the 1000BASE-T SFPs are your least expensive option. The alternative is MM or SM fiber.
    If you have to connect a Catalyst 3560 SFP interface to another Catalyst switch that takes GBICs, then the SFP Interconnect Cable is not even an option. From 0 to 100m, 1000BASE-T SFP and GBIC (WS-G5483=) would be your least expensive way to go.
    If there's any chance you will be redeploying these switches somewhere else in the future, you may want to put the 1000BASE-T SFPs in now. That way you'll already have them when you need them later.

  • Does Cisco ISE 1.2 support Catalyst SRW224G4P and Small business ESW520 Switches?

    Hello all,
    Does Cisco ISE 1.2 support Catalyst SRW224G4P and Small business ESW520 Switches?
    Best regards.

    Hi there, the link below outlines the ISE supported Cisco hardware:
    http://www.cisco.com/c/en/us/td/docs/security/ise/1-3/compatibility/ise_sdt.html
    Thank you for rating helpful posts!

  • Catalyst 3560 24 port-PoE switch powers on but no STAT LED and console not responding

    I rebooted my Catalyst 3560 24 port PoE switch and when it turned on only the STAT LED went green the other LEDs are off.  I get no response from the console port using putty and the cable I used before this happened.  I tested the cable on another switch and it works fine with putty.  What can I do with this switch?

    This unit was purchased before I came to our company.  There is no support or maint contract.  I'm sure the unit is several years old...we'll call the vendor and see what they'll do..not expecting much.

  • Assistance Disabling BPDU Guard: Catalyst 3560 CG

    Good Morning Guys,
    Here's the situation:
    Configuring  cisco wireless bridges -  every time I get both devices up in my wireless controller, the port my root bridge is connected to on the catalyst 3560 CG switch gets disabled with the following error:
    "SPANTREE - 2- BLOCK_BPDUGUARD: Received BPDU on port,  *** with BPDU Guard enabled, disabling port."
    I've done some research on BPDU Guard and I've tried applying the following commands to no avail:
    1. errdisable detect cause bpdguard shutdown vlan    (global and config mode)
    2. spanning-tree bpduguard disable           (configuration mode at the interface)
    any assistance to prevent the port from shutting down would be greatly appreciated.
    Christian

    You should double check the interface configs on both. It is shutting the port down because it is receiving BPDUs. This could be cause your switch port is configured for access but the WLC is configured as trunk...

  • 1000v uplink to Catalyst 4500

    We have a 1000v switch uplinked to nexus 5K and Catalyst 4500 switches. I can see all the VEMs(ESX servers) connected to the nexus 5K uplink switch and everything seems working fine. However, I am not able to see the VEMs uplinked to Cisco Catalyst 4500 switch. The "show  Module" command shows all VEMs connected to the nexus 5K uplink switches but not the Catalyst 4500 switches.The log file on the 1000V shows the following:
       7 09:36:21 NX-1K-100 %VMS-5-DVS_HOSTMEMBER_INFO: A host with name=[IP ADD. OF ESX SERVER] and uuid=[34393232-3035-3255-5839-3430303
    03537] is added to the dvs. The host is not found  as a module in the VSM configuration.
    If anyone have run into similar situation, plpease let me know how you handled it.
    Thanks

    Hi bharga,
    I did all the checking....
        1) all important VLANS including the control vlan are not blocked (No STP issue)
        2) The Nexus 5K and the 4500 switch are in layer layer 2  ( They are not directly connected but are in layer two domain or no hop between them)
       3) the ESX Server hosting the VSM is connected to the Nexus 5K 
    Here is some of the show commands that i run on the 4500 switch that is connects the ESX server to the rest ofd the network:-
    Catalyst-4500#sh spanning-tree interface gigabitEthernet 1/38
    Vlan                Role Sts Cost      Prio.Nbr Type
    VLAN0073            Desg FWD 4         128.38   P2p Edge
    VLAN0074            Desg FWD 4         128.38   P2p Edge
    VLAN0151            Desg FWD 4         128.38   P2p Edge
    VLAN0152            Desg FWD 4         128.38   P2p Edge
    VLAN0153            Desg FWD 4         128.38   P2p Edge
    VLAN0165            Desg FWD 4         128.38   P2p Edge
    Catalyst-4500#sh mac address-table interface gigabitEthernet 1/38
    Multicast Entries
    vlan    mac address     type    ports
    -------+---------------+-------+--------------------------------------------
      73    ffff.ffff.ffff   system Gi1/32,Gi1/38,Gi1/42,Gi1/45
      74    ffff.ffff.ffff   system Gi1/38,Gi1/41,Gi1/45
    151    ffff.ffff.ffff   system Gi1/3,Gi1/5,Gi1/6,Gi1/7,Gi1/9,Gi1/10,Gi1/11
                                    Gi1/12,Gi1/14,Gi1/16,Gi1/17,Gi1/18,Gi1/19
                                    Gi1/21,Gi1/22,Gi1/23,Gi1/25,Gi1/26,Gi1/27
    I still don't see the VEM  connected to port 1/38 of this switch on my nexus 1000v switch. The configuration file show exactly how many VEMs I have as shown below:
    Nexus-1000v# sh running-config
      host vmware id 34373030-3635-3255-5830-303630344
    vem 4
      host vmware id 34373030-3635-3255-5830-313130313
    vem 5
      host vmware id 34373030-3635-3255-5830-303630344
    vem 6
      host vmware id 34393232-3035-3255-5839-3134303537
    vem 7
      host vmware id 34373030-3635-3255-5830-313130313
    vem 8
      host vmware id 33393138-3335-5553-4539-31314e3438
    vem 9
      host vmware id 34393232-3035-3255-5839-3339303646
    vem 10
      host vmware id 34393232-3035-3255-5839-3430303035
    vem 11
      host vmware id 34393232-3035-3255-5839-3339303646
    But the show module command on the nexus 1000v shows only those VEMs coonected to the Nexus 5K switches and not those connected to the Catalyst 4500 switches.
    the uplink por-profile confguration on the Nexus 1000 V :
    vmware port-group
      switchport mode trunk
      switchport trunk native vlan 74
      switchport trunk allowed vlan 73-74,151-153,165,180,811,813,815,817-822,824,826-831
      channel-group auto mode on sub-group cdp
      no shutdown
      system vlan 74,180,811,819-821
      state enabled
    the corresponding interface on the 4500 switch :
    interface GigabitEthernet1/38
    switchport trunk encapsulation dot1q
    switchport trunk native vlan 74
    switchport trunk allowed vlan 73,74,151-153,165,180,811,813,815,817-822,824
    switchport trunk allowed vlan add 826-831
    switchport mode trunk
    mtu 9000
    spanning-tree portfast trunk
    I really appreciate in finiding out why I can't see the VEM (ESX Servers) connected to the 4500 switches.
    Thanks

  • Configuring the Catalyst 6500 Switch for IPS Inline Operation of the IDSM

    I understand how to configure the Catalyst 6500 switch so that the monitoring ports are access ports in two separate VLAN's for inline operation.
    However, I don't see any documentation that describes how the desired VLAN traffic gets forced through the IPS.
    In promiscuous mode, you can use VACL's to copy/capture and forward the desired traffic to the IDSM for analysis. I'm not seeing how to get the desired traffic through the IPS.
    Note that the host 6500 is running native IOS 12.2(18)SXE.
    Thanks for any assistance.

    A tranparent firewall is a fairly good comparison.
    Let's say you have vlan 10 with 100 PCs and 1 Router for the network.
    If you want to apply a transparent firewall on that vlan you can not simply put one interface of the firewall on vlan 10. Nothing would go through the firewall.
    Instead you have to create a new vlan, let's say 1010. Now you place one interface of the firewall on vlan 10 and the other on vlan 1010. Still nothing is going through the firewall. So now you move that Router from vlan 10 to vlan 1010. All you do is change the vlan, the IP Address and netmask of the router stay the same.
    The transparent firewall bridges vlan 10 and vlan 1010. The PCs on vlan 10 ae still able to communicate to and through the router, but must go through the transparent firewall to do so.
    The firewall is transparent because it does not IP Route between 2 vlans, instead the same IP subnet exists on both vlans and the firewall transparently beidges traffic between the 2 vlans.
    The transparent firewall can do firewalling between the PCs on vlan 10 and the Router on vlan 1010. But is PC A on vlan 10 talks to PC B on vlan 10, then the transparent firewall does not see and can not block that traffic.
    An InLine sensor is very similar to the transparent firewall and will bridge between the 2 vlans. And similarly an InLine sensor is able to InLine monitor traffic between PCs on vlan 10 and the Router on vlan 1010, but will not be able to monitor traffic between 2 PCs on vlan 10.
    Now the router on one vlan and the PCs on the other vlan is a typical deployment for inline sensors, but your vlans do not Have to be divided that way. You could choose to place some servers in one vlan, and desktop PCs in the other vlan. You subdivide the vlans in what ever method makes sense for your deployment.
    Now for monitoring multiple vlans the same principle still applies. You can't monitor traffic between machines on the same vlan. So for each of the vlans you want to monitor you will need to create a new vlan and split the machines between the 2 vlans.
    In your case with Native IOS you are limited to only 1 pair of vlans for InLine monitoring, but your desired deployment would require 20 vlan pairs.
    The 5.1 IPS software has now the capability to handle the 20 pairs, but the Native IOS software does not have the capability to send the 40 vlans (20 pairs) to the IDSM-2.
    The Native IOS changes are in testing right now, but I have not heard a release date for those changes.
    Now Cat OS has already made these changes. So here is a basic breakdown of what you could do in Cat OS and you can use in preparation for a Native IOS deployment when it gets released.
    For vlans 10-20, and 300-310 that you want monitored you will need to break each of those vlans in to 2 vlans.
    Let's say we make it simple and add 500 to each vlan in order to create the new vlan for each pair.
    So you have the following pairs:
    10/510, 11/511, 12/512, etc...
    300/800, 301/801, 302/802, etc....
    You set up the sensor port to trunk all 40 vlans:
    set trunk 5/7 10-20,300-310,510-520,800-810
    (Then clear all other vlans off that trunk to keep things clean)
    In the IDSM-2 configuration create the 20 inline vlan pairs on interface GigabitEthernet0/7
    Nw on each of the 20 original vlans move the default router for each vlan from the original vlan to the 500+ vlan.
    At this point you should ordinarily be good to go. The IDSM-2 won't be monitoring traffic that stays within each of the original 20 vlans, but Would monitor traffic getting routed in and out of each of the 20 vlans.
    Because of a switch bug you may have to have an additional PC moved to the same vlan as the router if the switch/MSFC is being used as the router and you are deploying with an IDSM-2.

  • MAC Addressess not showing on my new 3560 switch

    I have a Cisco 3560 (Switch B) switch I just introduced into my network.  The gigabit ports are trunked from another switch (Switch A) to a Cisco 6509 WS (Main Switch).
    crpf4bsw3#show cdp neighbors
    Device ID            Local Intrfce         Holdtme   Capability    Platform   Port ID
    crpf4bsw2.mdch.com
                        Gig 0/1               124            S I      WS-C3560-4Gig 0/4
    crpcorsw1.mdch.com
                        Gig 0/4               127           R S I     WS-C6509-EGig 2/8
    interface GigabitEthernet0/4
     switchport trunk encapsulation dot1q
     switchport trunk allowed vlan 1,19,124,150,160,164,168,224
     switchport mode trunk
     mls qos trust dscp
     spanning-tree link-type point-to-point
    interface GigabitEthernet0/1
     switchport trunk encapsulation dot1q
     switchport trunk allowed vlan 1,19,124,150,160,164,168,224
     switchport mode trunk
     mls qos trust dscp
     spanning-tree link-type point-to-point
    The trunk ports are working just fine.  I have configured all necessary remote management with no issues.  However, my access ports are not working.  I have set them up exactly the same as the adjacent switch A and it works just fine, but the same configuration on the new switch has not been able to pull IP information.  I have provided information as to how the switch access ports are configured on both Switch A (working) and Switch B (not working).  I should note that I tried this with a Cisco 7940 phone and it got stuck on "configuring IP" then I tried it with my laptop and it pulled a 169 IP address.  Both were direct connections into switch B.  When I run a show mac-address-table, neither device shows up in the table.  Only the gig port MACs.  Any thoughts? Please let me know if you need any more information.
    interface FastEthernet0/3
     switchport access vlan 124
     switchport mode access
     switchport voice vlan 224
     switchport port-security maximum 3
     switchport port-security
     switchport port-security aging time 2
     switchport port-security violation restrict
     switchport port-security aging type inactivity
     srr-queue bandwidth share 10 10 60 20
     srr-queue bandwidth shape  10  0  0  0
     mls qos trust device cisco-phone
     mls qos trust cos
     auto qos voip cisco-phone
     spanning-tree portfast
     spanning-tree bpduguard enable

    Hi Mike,
    It looks like you're guiding me in the right direction.  I did a "show port security interface fa0/2" on the new switch and nothing was out of the ordinary with the exception of the 0 MAC addresses learned.  But then I did a "show spanning tree vlan 224" Here's what I found:
    Switch A (existing switch):
    crpf4bsw2#show spanning-tree vlan 224
    VLAN0224
      Spanning tree enabled protocol rstp
      Root ID    Priority    4096
                 Address     0012.44cc.68e0
                 Cost        8
                 Port        1 (GigabitEthernet0/1)
                 Hello Time   2 sec  Max Age 20 sec  Forward Delay 15 sec
      Bridge ID  Priority    32992  (priority 32768 sys-id-ext 224)
                 Address     0013.60aa.7400
                 Hello Time   2 sec  Max Age 20 sec  Forward Delay 15 sec
                 Aging Time 300
    Interface        Role Sts Cost      Prio.Nbr Type
    Gi0/1            Root FWD 4         128.1    P2p
    Fa0/1            Desg FWD 19        128.3    Edge P2p
    Fa0/2            Desg FWD 19        128.4    Edge P2p
    Fa0/3            Desg FWD 19        128.5    Edge P2p
    Fa0/4            Desg FWD 19        128.6    Edge P2p
    Fa0/5            Desg FWD 19        128.7    Edge P2p
    Fa0/6            Desg FWD 19        128.8    P2p Peer(STP)
    Interface        Role Sts Cost      Prio.Nbr Type
    Fa0/7            Desg FWD 19        128.9    Edge P2p
    Fa0/8            Desg FWD 19        128.10   Edge P2p
    Fa0/9            Desg FWD 19        128.11   Edge P2p
    Fa0/10           Desg FWD 19        128.12   Edge P2p
    Fa0/11           Desg FWD 19        128.13   Edge P2p
    Fa0/12           Desg FWD 19        128.14   Edge P2p
    Fa0/13           Desg FWD 19        128.15   Edge P2p
    Fa0/15           Desg FWD 19        128.17   Edge P2p
    Fa0/19           Desg FWD 19        128.21   Edge P2p
    Fa0/20           Desg FWD 19        128.22   Edge P2p
    Gi0/4            Desg FWD 4         128.28   P2p
    Fa0/29           Desg FWD 19        128.33   Edge P2p
    Fa0/30           Desg FWD 19        128.34   Edge P2p
    Fa0/31           Desg FWD 19        128.35   Edge P2p
    Fa0/32           Desg FWD 19        128.36   Edge P2p
    Fa0/33           Desg FWD 19        128.37   Edge P2p
    Fa0/34           Desg FWD 19        128.38   Edge P2p
    Fa0/35           Desg FWD 19        128.39   Edge P2p
    Fa0/37           Desg FWD 19        128.41   Edge P2p
    Fa0/38           Desg FWD 19        128.42   Edge P2p
    Fa0/39           Desg FWD 19        128.43   Edge P2p
    Fa0/40           Desg FWD 19        128.44   Edge P2p
    Fa0/41           Desg FWD 19        128.45   Edge P2p
    Interface        Role Sts Cost      Prio.Nbr Type
    Fa0/42           Desg FWD 19        128.46   Edge P2p
    Fa0/43           Desg FWD 19        128.47   Edge P2p
    Fa0/44           Desg FWD 19        128.48   Edge P2p
    Fa0/45           Desg FWD 19        128.49   Edge P2p
    Fa0/46           Desg FWD 19        128.50   Edge P2p
    Switch B (new switch):
    Spanning tree instance(s) for vlan 224 does not exist.
    So with this new information, and with my trunk configurations above, what did you mean by a disconnect on the trunk?

  • 1142N NON_CISCO-NO_CDP_RECEIVED with 3560 switch

    I thought the 3560 switches, the 8 port and 24 port are 802.3af standard switches?  When I connect 1142N radios to them I get the no cdp error and the radios are disabled. I have 17 of these that I converted to LAP, and I got the issue both before and after upgrading to LAP from AP.  It's not like I disabled CDP on the switches.

    I may have found the problem. I thought I had initially connected to a switchport that was just setup as a switchport access vlan, with no other configurations on it, and after looking at the port found it was a trunk port, which should work, and does for the other AP's I worked with, but not the 1142N.
    I took one of the other AP's that is connected to the test switch I am using to setup the WLC and AP's and connected that to one of the unconfigured ports, with default settings and the radios both powered up and I saw CDP neighbor detail,
    I removed spanning-tree portfast from the trunk port, and reconnected the AP to that port, I saw it negotiated full power, but I dont see neighbor information. I had to console in and do a no shut on dot11radio 0 for it to come up on all 3 of them.
    I went back and pulled that new one out of the box and reconnected to the interface I used before after removing portfast, still had the same problem, then removed the trunk configuration, and rebooted. Now I see
    *Mar  1 00:14:19.266: %CDP_PD-2-POWER_LOW: All radios disabled - NEGOTIATED WS-C3560-8PC
    Fa0/6     auto   on         14.5    AIR-LAP1142N-A-K9   3     15.4
    I took one of the other AP's that I boxed up and connected it to the same port, this was a converted AP to LAP.
    Fa0/6     auto   on         15.4    AIR-LAP1142N-A-K9   3     15.4
    Futher puzzlement, plugged that last AP into the test switch which is setup to mimic a remote location with trunk ports for FlexConnect, and after the radio powered up, and joined the controller, saw this.
    wmmAC status is FALSE
    *May 30 08:15:02.896: Starting Ethernet promiscuous mode
    *May 30 08:15:03.150: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to administratively down
    *May 30 08:15:03.222: %LWAPP-3-CLIENTEVENTLOG: OfficeExtend Localssid saved in AP flash
    *May 30 08:15:03.629: %CAPWAP-5-JOINEDCONTROLLER: AP has joined controller WLC-2504
    *May 30 08:15:03.677: %LWAPP-3-CLIENTEVENTLOG: SSID wlcman added to the slot[0]
    *May 30 08:15:03.710: %LWAPP-3-CLIENTEVENTLOG: SSID internal added to the slot[0]
    *May 30 08:15:04.137: %LWAPP-3-CLIENTEVENTLOG: SSID guest added to the slot[0]
    *May 30 08:15:04.269: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
    *May 30 08:15:04.461: %LINK-3-UPDOWN: Interface Dot11Radio1, changed state to down
    *May 30 08:15:04.462: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
    *May 30 08:15:04.552: %LWAPP-3-CLIENTEVENTLOG: SSID wlcman added to the slot[1]
    *May 30 08:15:04.553: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
    *May 30 08:15:04.575: %LWAPP-3-CLIENTEVENTLOG: SSID internal added to the slot[1]
    *May 30 08:15:05.010: %LWAPP-3-CLIENTEVENTLOG: SSID guest added to the slot[1]
    *May 30 08:15:05.866: %DOT11-6-DFS_SCAN_START: DFS: Scanning frequency 5300 MHz for 60 seconds.
    *May 30 08:15:06.055: %LINK-3-UPDOWN: Interface Dot11Radio1, changed state to up
    *May 30 08:15:06.351: %WIDS-6-ENABLED: IDS Signature is loaded and enabled
    *May 30 08:15:07.187: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to up
    *May 30 08:15:07.215: %LINK-3-UPDOWN: Interface Dot11Radio1, changed state to down
    *May 30 08:15:07.216: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
    *May 30 08:15:08.223: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
    *May 30 08:15:08.237: %DOT11-6-DFS_SCAN_START: DFS: Scanning frequency 5300 MHz for 60 seconds.
    *May 30 08:15:08.237: %LINK-3-UPDOWN: Interface Dot11Radio1, changed state to up
    *May 30 08:15:09.245: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to up
    Why would radio 0 be admin down? It is enabled on the WLC.  I went into the AP and did a no shut on it too.  Not sure what is going on with this, never ran into this sort of issue before.

  • Cisco 3560 switch| mls qos trust dscp question

    Hi everybody
    Hi everybody .
    Please consider the following example:
    3560 sw f1/1--------trunk---SW2
    3560 sw
    f1/1
    mls qos trust dscp
    3560 is using default cos-dscp map, assume a 3560 receives a frame carrying IP packet on f1/1 with COS 4, what will 3560 switch do?
    1) will it use its default cos --dscp map  ( cos 4--.dscp 32) and rewrite 32 in dscp field  of the packet in the frame and provide PHB for dscp 32 ?
    Much appreciated!!
    Have  a great weekend.

    Hi
    No it will not trust the cos value, because You have configured to trust dcsp. So, the switch will trust the dcsp value in the incoming frame.
    /Mikael

  • Vlan mapping cisco catalyst 3560

    Hello
    which Cisco switches support vlan mapping ?
    and did Cisco catalyst 3560 support vlan mapping or not ??
    thank u

    Thank u pdanekul
    I know 3750 support vlan mapping but with 3560 i can not see vlan mapping config
    switchport vlan mapping
    and also i can not see it in cisco Catalyst 3560 Software Configuration Guide, Release 12.2(52)SE
    http://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst3560/software/release/12-2_52_se/configuration/guide/3560scg/swtunnel.html

Maybe you are looking for

  • I have a license for CS6 and need to add another license. Am I still able to purchase one?

    I have a license for Adobe CS6 for 6 designers. We may be hiring another designer in the next few months. I need to know if I am still able to purchase another license for CS6. I looked at the site and can't see where I would find that info and don't

  • Dynamic WebService Proxy

    How can I configure dynamic Web Service Proxy for a WSDL in Web Center Application. Any change in the WSDL, we need to create a new proxy and thus re-create Data Control again in the Model. Any samples or answers are highly appreciated.

  • Need help with a JavaScript to generate random number

    Hi First things first. I don't know the J of JavaScript. When I was thinking of some readymade solution to generate a random number in Captivate, I found this on a LinkedIn forum. 1) Add a user variable to your project called "randomNumber". It's val

  • Fm BAPI_BUS2175_SET_STATUS in workflow

    Hi, On Phase release, I am trying to set the task status to user defined statusin workflow. But it gives locking issue. It says object is locked. Can anybody help on this? Thanks in advance. harshada

  • JTableHeader and LookAndFeel problem

    need help in solving the following problems 1. i have a JTable that i want to display information in the table header from a JTextField am using to input data.please how do i handle it. inputfield = new JTextField(20); tablemodel = new DefaultTable()