SSM 7 - Maximums
Hi all,
Could someone please explain the difference between the following maximums found on page 112 and 113 of the pdf entitled 'SAP Strategy Management 7.0- Delta from SSM 2007 to SSM 7.0':
Administrator's Interface Maximums
Item Maximum number allowed
1. # standard KPIs per context Standard = 100, Custom = 100 more. Total of up to 200.
Dimensional Model Maximums
Database Maximum
2. # Measures in a dimensional model 1 500
3. # KPIs per dimensional model 400 standard and index KPIs combined.
In addition, I have created 200 kpis in the cube builder and get a message in the trace file that the maxium number of variables have been reached i.e. 1000, this is lower than point 2 above. Why would the maxiumums be different?
Finally, is there a way to exceed these maximums?
Thanks in advance,
T
Taariq,
You have a limit of KPIs you can normally create for each context, and that is what the Administrator's Interface Maximums relate to. Usually this should be more than enough for the implementation of any single scorecard.
As for the Dimensional Models Maximums, these relate to the Application Server Models, and you will find also documentation on this in the Application Server Help. When you create a model through Cube Builder, it will use the standard model definitions - 1000 measures maximum. You can change this limit afterwards directly in the Application Server with the IDQL command:
SUP CHANGE DATABASE yourdb VARIABLES 1500
(check in the AS Help what are the Application Server maximums for the version you are running!)
You should be able to resume with model creation through Cube Builder after you have made this change.
Best regards!
Ricardo
Similar Messages
-
What to expect when ASA AIP SSM reaches maximum throughput?
Hi,
I'm just curious what happens to traffic when you have an IPS module in an ASA and it reaches the maximum throughput?
Does it allow the traffic & only inspects what it can handle? Or does it "fail" and then either allows all the traffic or block based on "fail-open" or "fail-close" configuration?
Thanks,
BradWhen the sensor (SSM or any other sensor) is oversubscribed and the sensor is monitoring Inline, then a portion of the traffic will be Dropped.
The traffic will not be allowed through if it has not been inspected.
The "fail-open", "fail-close", and "bypass" are not relevant when talking about over subscription.
The only time the "fail-open", "fail-close", or "bypass" configurations comes into play is if the sensor can not do ANY analysis (either a failure, or an upgrade in progress). -
Hi All,
I´m working with Cube Builder and need know about some limitations in the creation process.
How many dimensions can I create into CB (in the same Cube)?
How many measures/indicatores can I create into CB (in the same Cube)?
How many Dimensional Models can I create into CB?
I´m assuming that I´m working without Application Server, just with Cube Builder .
Best Regards,
Bruno HeisslerPlease go through the below link which has been discussed earlier on the similar kind, in depth by our members, for your more insight.
SSM 7 - Maximums
..for more informn on this, pl review the same with www.help.sap.com.
hope this information will be helpful to you for some extent.
thanks
ukraghu -
Multiple KPI for the same Initative or Perspective
Hi all,
Here we are facing a problem with a customer BSC model that we need to adapt to SAP SSM
The customer has the following BSC structure ":
1) Multiple KPIs for ONE Perspective ( in SSM the maximum that we have it is a Perpective related to one KPI )
2) Multiple KPIs for an Objective ( Ok, SSM is OKJ in this point )
3) Multiple KPIs for an Initiative ( in this customer they use a Initiative as a lower level of the Objective )
( in SSM a Initiative is associated only with one KPI if necessary )
As we can see the itens 1 and 3 I see a limitation to adopt in SSM cause SSM does not provide a n for n relationship ( Multiple KPIs for One Perspective and
Multiples KPIs for a same Initiative )
Does somebody knows how can I solve this kind of SAP SSM tool limitation ?
Regards,
AlfredAlfred,
Index KPIs is going to be the solution for each of these questions.
1) Multiple KPIs for ONE Perspective ( in SSM the maximum that we have it is a Perpective related to one KPI )
SSM is set up in a hierarchical structure, so that the assumption is that KPIs drive Objectives and Objectives drive the status of the Perspectives. If you have multiple KPIs that are going to drive the status of a Perspective, you would have to create an INDEX KPI in Set KPIs. Then you can assign that KPI as the status driver for your Perspective.
2) Multiple KPIs for an Objective ( Ok, SSM is OKJ in this point )
Index KPIs need to be created.
3) Multiple KPIs for an Initiative ( in this customer they use a Initiative as a lower level of the Objective )
Initiatives are set to be tied to Perspectives and Objectives and you have the option of setting a Status for that Initiative based on a KPI. Again, you can create an Index KPI if you need multiple KPIs to drive the status of an Initiative
The reason that you have to create these in Set KPIs and then assign that Index KPI to Perspectives and Initiatives is that you need to use that Set KPIs area to set and define the relationships and relative values of the combined KPIs.
Regards,
Bob -
Can't Send or Receive Email from Exchange behind ASA 5510 with CSC SSM
We are upgrading from a Pix 515e to a ASA 5510 with CSC SSM. We cannot send outbound email or receive any email from the outside world. I have placed a call with Cisco Support with no luck. Here is a copy of my config: Any Help would be appreciated.
show config
: Saved
: Written by enable_15 at 07:17:44.760 CST Wed Jan 18 2012
ASA Version 8.4(3)
names
interface Ethernet0/0
nameif outside
security-level 0
ip address 216.XXX.XXX.XXX 255.XXX.XXX.XXX
interface Ethernet0/1
nameif inside
security-level 100
ip address 192.168.0.5 255.255.255.0
interface Ethernet0/2
shutdown
no nameif
no security-level
<--- More --->
no ip address
interface Ethernet0/3
shutdown
no nameif
no security-level
no ip address
interface Management0/0
shutdown
nameif management
security-level 100
no ip address
management-only
boot system disk0:/asa843-k8.bin
ftp mode passive
clock timezone CST -6
clock summer-time CDT recurring
object network obj-192.168.5.0
subnet 192.168.5.0 255.255.255.0
object network obj-192.168.0.0
subnet 192.168.0.0 255.255.255.0
<--- More --->
object network obj-192.168.9.2
host 192.168.9.2
object network obj-192.168.1.65
host 192.168.1.65
object network obj-192.168.1.0
subnet 192.168.1.0 255.255.255.0
object network obj-192.168.2.0
subnet 192.168.2.0 255.255.255.0
object network obj-192.168.3.0
subnet 192.168.3.0 255.255.255.0
object network obj-192.168.6.0
subnet 192.168.6.0 255.255.255.0
object network obj-192.168.8.0
subnet 192.168.8.0 255.255.255.0
object-group service DM_INLINE_TCP_1 tcp
port-object eq ftp
port-object eq www
port-object eq pop3
port-object eq smtp
object-group network Red-Condor
description Email Filtering
network-object host 66.234.112.69
network-object host 66.234.112.89
object-group service NetLink tcp
<--- More --->
port-object eq 36001
object-group network AECSouth
network-object 192.168.11.0 255.255.255.0
object-group service Email_Filter tcp-udp
port-object eq 389
object-group protocol TCPUDP
protocol-object udp
protocol-object tcp
object-group service DM_INLINE_TCP_0 tcp
group-object Email_Filter
port-object eq pop3
port-object eq smtp
object-group network Exchange-Server
description Exchange Server
network-object host 192.168.1.65
access-list global_mpc extended permit tcp any any object-group DM_INLINE_TCP_1
access-list outside_access extended permit tcp any object obj-192.168.9.2
access-list outside_access extended permit icmp any any
access-list outside_access extended permit tcp any object-group Exchange-Server eq https
access-list outside_access extended permit tcp object-group Red-Condor object-group Exchange-Server eq smtp
access-list outside_access extended permit tcp object-group Red-Condor object-group Exchange-Server eq pop3
access-list outside_access extended permit object-group TCPUDP object-group Red-Condor object-group Exchange-Server object-group Email_Filter
access-list inside_access_in extended permit ip any any
access-list inside_access_in extended permit icmp any any
<--- More --->
pager lines 24
logging enable
logging console debugging
logging asdm informational
mtu outside 1500
mtu inside 1500
mtu management 1500
ip local pool vpnpool 192.168.5.1-192.168.5.254 mask 255.255.255.0
icmp unreachable rate-limit 1 burst-size 1
icmp permit any outside
icmp permit any inside
asdm image disk0:/asdm-647.bin
no asdm history enable
arp timeout 14400
object network obj-192.168.9.2
nat (inside,outside) static 216.XXX.XXX.XXX no-proxy-arp
object network obj-192.168.1.65
nat (inside,outside) static 216.XXX.XXX.XXX no-proxy-arp
object network obj-192.168.1.0
nat (inside,outside) dynamic interface
object network obj-192.168.2.0
nat (inside,outside) dynamic interface
object network obj-192.168.3.0
<--- More --->
nat (inside,outside) dynamic interface
object network obj-192.168.6.0
nat (inside,outside) dynamic interface
object network obj-192.168.8.0
nat (inside,outside) dynamic interface
access-group outside_access in interface outside
access-group inside_access_in in interface inside
route outside 0.0.0.0 0.0.0.0 216.XXX.XXX.XXX 1
route inside 192.168.0.0 255.255.0.0 192.168.0.1 1
timeout xlate 3:00:00
timeout pat-xlate 0:00:30
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
aaa-server isaconn protocol radius
aaa-server isaconn (inside) host 192.168.1.9
timeout 5
key XXXXXXX
user-identity default-domain LOCAL
aaa authentication ssh console LOCAL
<--- More --->
http server enable
http 192.168.0.0 255.255.0.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec ikev1 transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec ikev1 transform-set AEC esp-des esp-md5-hmac
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set pfs group1
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map outside_map interface outside
crypto ca trustpoint _SmartCallHome_ServerCA
crl configure
crypto ca server
shutdown
<--- More --->
smtp from-address [email protected]
crypto ca certificate chain _SmartCallHome_ServerCA
certificate
quit
crypto ikev1 enable outside
crypto ikev1 policy 10
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
telnet 192.168.0.0 255.255.0.0 inside
telnet timeout 5
ssh 192.168.0.0 255.255.0.0 inside
ssh timeout 5
console timeout 0
management-access inside
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
ntp server 208.66.175.36 source outside prefer
webvpn
username cisco password 3USUcOPFUiMCO4Jk encrypted privilege 15
<--- More --->
class-map global-class
match access-list global_mpc
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
<--- More --->
inspect netbios
inspect tftp
inspect ip-options
class global-class
csc fail-close
service-policy global_policy global
prompt hostname context
call-home reporting anonymousHello Scott,
So Exchange server ip is obj-192.168.1.65 natted to 216.x.x.x
object network obj-192.168.1.65
"nat (inside,outside) static 216.XXX.XXX.XXX no-proxy-arp"
The ACL says
access-list outside_access extended permit tcp object-group Red-Condor object-group Exchange-Server eq smtp
access-list outside_access extended permit tcp object-group Red-Condor object-group Exchange-Server eq pop3
From witch ip addresses are you trying to send traffic to the exchange server?
Please do a packet-tracer and give us the output
packet-tracer input outside tcp x.x.x.x( Outside host ip) 1025 216.x.x.x.x 25
Regards,
Julio
Rate helpful posts!!! -
Maximum index key length exceeded
Hi,
I am getting following error on executing this command in MS SQL server 2012-
Command -
alter table <table1_name> add constraint <constraint name> foreign key (<column1 name>) references <table2_name>(<column2_name>)
Error -
System Error: #1400025: Maximum index key length exceeded
Warning: #1500562: Index will apply to all business objects
Any suggestion on what I can check in this case?
Thanks.alter table <table1_name> add constraint <constraint name> foreign key (<column1 name>) references <table2_name>(<column2_name>)
Error -
System Error: #1400025: Maximum index key length exceeded
Warning: #1500562: Index will apply to all business objects
Any suggestion on what I can check in this case?
This is not a SQL Server error. What tool are you using? If you are using SSMS, maybe a DDL trigger?
Dan Guzman, SQL Server MVP, http://www.dbdelta.com -
I have a couple of questions regarding the ASA that deal with the SSM module.
I have read the document "Configuring ASA-SSM" and am confused by the command logic. I realize that you need to specify a service-policy globally that defines the traffic being sent to the SSM module. My concern is that the configuration document lists as one of it's steps to define an ACL for the IPS traffic and then apply it to an interface before configuring the class map, policy map, and service-policy. Why would this ACL need to be applied to an interface when it is being used for defining IPS traffic? Shouldn't the ASA send whatever traffic is defined globally in the service-policy to the SSM without attaching the ACL to an interface?
Also, on the ASA factory default configuration there is a service-policy defined as:
class-map inspection_default
match default-inspection-traffic
policy-map global_policy
class inspection_default
inspect dns maximum-length 512
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
service-policy global_policy global
But, if I define a global service-policy for the SSM I would lose this default service-policy as only one global service policy is allowed. Is the default service-policy providing the fixup protocol services as in the PIX that I am used to seeing? If so do I lose this functionality by applying a global service-policy for IPS/
Sorry for the length of the post and thanks for your help in advance.The configuration in the IPS User's Guide is just one method for settings up the ASA to send packets to the SSM.
It is an extremely basic configuration on the ASA where all the ASA is doing is copying packets to the SSM and the ASA is not doing any of it's firewall functionality.
This configuration is only practical if the ASA was purchased and used only for housing the SSM and sending it traffic ( a rare deployment in the field ).
If your ASA is already configured for firewall functionality then the only additional command(s) that need to be added to your config are:
ips inline|promiscuous fail-open|fail-close
Take your existing policy-map and for every class in that policy you will need to decide if the traffic should be monitored promiscuously, inline, or not monitored by the SSM.
In your example, if you wanted to monitor all of the traffic inline on the SSM and want to continue passing traffic if the SSM fails. Then simply add the line "ips inline fail-open" within the existing "class inspection_default".
NOTE: If you change the policy you need to understand that the new policy will only affect new connections and not existing connections.
The only reason you would have to create additional acls and class maps using the acls would be if you did not want all of the traffic monitored inline by the SSM.
If you want different traffic monitored promiscuous and other inline (or not monitored), then you need to include additional classes in your policy-map so that a different ips configuration line can be added for each class. -
I have recently confgured my AIP-SSM-20 module in my firewalls (ASA 5540) which are configured in HA(Active/Standby).This implementation i have done on 13th June. It was working fine.
Now, i have observerd that the AIP-SSM-20 module in the primary firewall had gone to unresponsive state.
Below is the status of show module and show failover command.
FW1-5540# sh module
Mod Card Type Model Serial No.
0 ASA 5540 Adaptive Security Appliance ASA5540 JMX1234L11F
1 ASA 5500 Series Security Services Module-20 ASA-SSM-20 JAF1341ADPS
Mod MAC Address Range Hw Version Fw Version Sw Version
0 0021.d871.77ab to 0021.d871.77af 2.0 1.0(11)4 8.0(3)6
1 0023.ebf6.11ce to 0023.ebf6.11ce 1.0 1.0(11)5 6.2(2)E4
Mod SSM Application Name Status SSM Application Version
1 IPS Not Applicable 6.2(2)E4
Mod Status Data Plane Status Compatibility
0 Up Sys Not Applicable
1 Unresponsive Not Applicable
FW1-5540# sh failover
Failover On
Failover unit Primary
Failover LAN Interface: FAILOVER GigabitEthernet0/2 (up)
Unit Poll frequency 1 seconds, holdtime 15 seconds
Interface Poll frequency 5 seconds, holdtime 25 seconds
Interface Policy 1
Monitored Interfaces 3 of 250 maximum
Version: Ours 8.0(3)6, Mate 8.0(3)6
Last Failover at: 09:06:14 UTC Jun 15 2010
This host:
This host: Primary - Failed
Active time: 191436 (sec)
slot 0: ASA5540 hw/sw rev (2.0/8.0(3)6) status (Up Sys)
Interface DMZ_LAN (10.192.153.13): Normal (Waiting)
Interface INTRANET (10.192.154.13): Normal (Waiting)
Interface management (0.0.0.0): Link Down (Waiting)
slot 1: ASA-SSM-20 hw/sw rev (1.0/6.2(2)E4) status (Unresponsive/Down)
IPS, 6.2(2)E4, Not Applicable
Other host: Secondary - Active
Active time: 192692 (sec)
slot 0: ASA5540 hw/sw rev (2.0/8.0(3)6) status (Up Sys)
Interface DMZ_LAN (10.192.153.5): Unknown (Waiting)
Interface INTRANET (10.192.154.5): Unknown (Waiting)
Interface management (0.0.0.0): Unknown (Waiting)
slot 1: ASA-SSM-20 hw/sw rev (1.0/7.0(2)E4) status (Up/Up)
IPS, 7.0(2)E4, Up
Stateful Failover Logical Update Statistics
Link : Unconfigured.
I have tried using the
hw-module module 1 reset
to reset the IPS module but the status is always unresponsive.
Its production environment where i cannnot expirement much. Ned help to rectify the problem.Hi Scott,
I have almost same problem of sbgcsd in my customer. I'm deploying two ASA-5512 in failover configuration. One day, after almost 2 months testing project in a lab, when we install in customer's datacenter the systems presented following errors:
ciscoasa2(config)# failover
Detected an Active mate
ciscoasa2# Mate NOT PRESENT card in slot 1 is different from mine IPS5512
I tried to discover what was happened with IPS modulo, then I saw error in IPS status: "Unresponsive".
ciscoasa2# sh module ips
Mod Card Type Model Serial No.
ips Unknown N/A FCH1712J7UL
Mod MAC Address Range Hw Version Fw Version Sw Version
ips 7cad.746f.8796 to 7cad.746f.8796 N/A N/A
Mod SSM Application Name Status SSM Application Version
ips Unknown No Image Present Not Applicable
Mod Status Data Plane Status Compatibility
ips Unresponsive Not Applicable
Mod License Name License Status Time Remaining
ips IPS Module Disabled perpetual
According with Cisco Foruns I tried to "Reloading, Shutting Down, Resetting, and Recovering AIP-SSM" (*) using "hw-module module " command. But unfortunatelly ASA didn't accept this command. See below:
ciscoasa2# hw-module module 1 reload
^
ERROR: % Invalid input detected at '^' marker
What happened with this command (hw-module) ? Maybe is a problem in Software version ? When I entered "sh flash" command I saw that didn't exist any software for AIP-SMM module:
ciscoasa2# sh flash
--#-- --length-- -----date/time------ path
11 4096 Sep 12 2013 13:56:54 log
21 4096 Sep 12 2013 13:57:10 crypto_archive
100 0 Sep 12 2013 13:57:10 nat_ident_migrate
22 4096 Sep 12 2013 13:57:10 coredumpinfo
23 59 Sep 12 2013 13:57:10 coredumpinfo/coredump.cfg
101 34523136 Sep 12 2013 14:00:14 asa861-2-smp-k8.bin
102 17851400 Sep 12 2013 14:04:36 asdm-66114.bin
103 38191104 Apr 24 2014 12:59:58 asa912-smp-k8.bin
104 6867 Apr 24 2014 13:01:20 startup-config-jcl.txt
105 24095116 Jun 17 2014 14:54:14 asdm-721.bi
But another ASA (#1) have image:
ciscoasa1# sh flash
--#-- --length-- -----date/time------ path
11 4096 Sep 10 2013 06:42:56 log
21 4096 Apr 17 2014 03:13:12 crypto_archive
123 5276864 Apr 17 2014 03:13:12 crypto_archive/crypto_eng0_arch_1.bin
110 0 Sep 10 2013 06:43:12 nat_ident_migrate
22 4096 Sep 10 2013 06:43:12 coredumpinfo
23 59 Sep 10 2013 06:43:12 coredumpinfo/coredump.cfg
111 34523136 Sep 10 2013 06:44:24 asa861-2-smp-k8.bin
112 42637312 Sep 10 2013 06:45:46 IPS-SSP_5512-K9-sys-1.1-a-7.1-4-E4.aip <===
But I am not sure if this image is really the right image do AIP-SSM in ASA#2. But anyway I copy (through a simple TFTP server) from ASA#1 to ASA#2 , but after this, the same problem ramained !
Because I didn't applied the Failover condition to system.
What can I do now ?
Thank you very much in advance.
Leonardo_Melo.(CCAI-JCL-Brazil). -
ASA-SSM-10 inspection load 100% (version 7.0(5a)E4
Hi all,
I have a challenge with the IPS module in the ASA5520, the ASA-SSM-10. When we start a test to connect to the webservers I get a inspection load of 100% and traffic/performance will slow down.
We test with 63000 sessions per minute which perform a load of: from the test-servers(clients) to the web-servers of 20.000 kbits/sec and traffic from the web-servers back to the test-servers(clients) 75.000 kbits/sec.
Can you please advise what to do because we cannot go live with this environment only when this is fixed.
Thanks in advance,
Erik Verkerk.Hi Bob,
thanks for you reply/suggestion and you understood the numbers correctly. Unfortunately the AIP-SSM-10 module must inspect this kind of load. I can test, within 8 hours time, a lower amount of traffic.
I do have some questions for you:
When you have a traffic of 75Mb/s what is your inspection load saying 80%?
Regarding the specs Cisco tells in the documentation of the ASA5520 that when you are using a AIP-SSM-10 you can firewalling and IPS a maximum of 225Mb/s. Now I understand that this is probably the commercial figures but Iám only looking for half of this, 95MB/s. Do you have an explaination for this?
Perhaps the amount of signatures is too much: I have 1500 signatures active, can you tell how much active signatures you run in your AIP-SSM-10?
Last but not least question:
It is hard for me to find some usefull documentation, specific troubleshooting the IPS, do you have suggestions?
I hope you have the time to answers these questions it certainly helps me to understand the IPS and fix the problem.
Many thanks in advance,
Erik. -
SSMS Addin - How To Access Query Results Grid
Hi,
I want to access Query Result Grid(Results) in SSMS addin but I did'nt found anything.
How can I access Query Result Grid, Rows, Columns and Cells when I executed a script?
Thanks.SQL Server Management Studio currently supports query execution results to be displayed in three different ways: Results to Grid,
Results to Text and Results to File.
By default SQL Server Management Studio is configured to display query results in
Grid format. If you want to change the default to some other option follow these steps.
1. In SQL Server Management Studio, under Tools menu, click
Options as shown in the snippet below.
2. In the Options dialog box, expand Query Results, expand
SQL Server and then select General as shown in the snippet below. In the right side panel choose one of the three options shown below in the
Default Destination for results drop down list and click
OK to save the changes as shown in the snippet below. The changes will go into effect once you open a New Query window.
Query Result Options for Results to Text
In this format you have the option to display the results in a different tab as well as setting different output options.
In the Options dialog box, expand Query Results, expand
SQL Server and then select Results to Text tab as shown in the snippet below. In the right side panel first select the checkbox for
Display results in a separate tab and then select the checkbox for
Switch to results tab after the query executes and then click
OK. If you would like to also display the column name in the result set then choose the option Include column headers in the result set
as shown in the snippet below.
The options you can use in the Text format are:
Output format: - In the above snippet you could see that by default the output is displayed as columns aligned. Some of the other options that are available are Comma Delimited,
Tab Delimited, Space Delimited and Custom Delimited. If you choose the Custom Delimited option in the Output format drop down list then you need to specify a character of your choice for the delimiter in the
Custom delimiter text box.
Include column headers when copying or saving the results: - If this option is selected, then whenever the results are copied to clipboard or it is saved to a file the column headers are also copied along with the results.
Include the query in the result set: - The text of the query is displayed as part of query output under the messages tab.
Scroll as results are received: - If this option is selected, then the display focuses on the most recently returned records at the end of the results set.
Right align numeric values: - If this option is selected, then numeric values will be aligned to the right of the column.
Discard results after query executes: - If this option is selected, then the query results are not displayed in the reviewing pane.
Display results in a separate tab: - If this option is selected, then the result set after query execution will be displayed in a new tab instead of at the bottom of the query window.
Switch to results tab after the query executes: - If this option is selected, then after the query execution the screen focus will be set to the results tab.
Maximum number of characters displayed in each column: - This sets the maximum characters to display for any one column. So if you have a column that is 500 characters this will only show the first 256 if you keep the default setting.
Ref link :http://www.mssqltips.com/sqlservertip/2346/different-options-for-query-results-in-sql-server-management-studio/
Ahsan Kabir Please remember to click Mark as Answer and Vote as Helpful on posts that help you. This can be beneficial to other community members reading the thread. http://www.aktechforum.blogspot.com/ -
SSM- LIMIT THE PERFORMANCE OF AN INDICATOR
Is there any way to limit the performance of an indicator?. For example if the target of a pointer is 5 and the result is 15, the performance would be 300%. However, company policy where I work requires a maximum of 110% compliance to pay a wage variable. All compliance above 110 should be truncated to 110%.
Hi Miguel
I didn´t know about the Application Server Administrator, the company that installed us the SSM has given us the SSM tools, String Editor and SAP NetWeaver Application Server and obviously the screen where you enter KPIs and other information. Where do I find the Application Server Administrator? -
Mini-DVI to VGA maximum resolution?
I have an external monitor with only VGA input, and it's resolution is 1680 x 1050. Will my MacBook be capable of using this display at it's native resolution using a mini-DVI to VGA adapter?
The display is the HP w2007v in case anyone is interested.
ThanksHi Josh,
taken from Apple Video Developer Note found here:
http://developer.apple.com/documentation/Hardware/Conceptual/HWTechVideo/Articles/Video_implementation.html#//apple_ref/doc/uid/TP40003994-SW741200331181
External Display Modes
The default display mode setting on the MacBook is extended desktop display. To toggle between the two modes, press the F7 key, or go to System Preferences>Displays>Arrangement.
A scaling function is available when the internal display and an external monitor are both operating and the mirror mode is selected. However, the external monitor could have black borders during mirroring, depending on the supported timings between the two displays and on the monitor’s selection algorithm. Black borders are not seen on VGA displays.
Both displays show full-sized images when the display resolution for the external monitor is set to the internal display’s native resolution: 1280 by 800. Both displays can operate with other resolution settings, but in mirror mode, one of the displays may be smaller than the full screen and have a black border around it. With the resolution for the external monitor set to less than 1280 by 800, the image on the internal display is smaller than its screen. For resolution settings larger than 1280 by 800, the image on the external monitor is smaller than its screen.
In mirror mode, the maximum size of the external display is 1280 by 800 at 60 Hz. In extended desktop mode, the maximum size of the external display is 1920 by 1200 at 60 Hz.
So in extended mode the 1680x1050 resolution should be avaiable.
Hope it helps
Stefan -
T61 - Half theCore speed at maximum performanc​e mode.
Hello,
My T61 was bought during March 2008. I recently installed CPU-Z and was bit worried since under maximum performance mode, the CPU was not throttling to full speed (with AC power).
The core speed is showing approximately 1200MHz. FSB is showing around 800Mhz. It is a penryn T9300 processor and I believe it should be 2500Mhz. Is there a setting somewhere on the power options that needs to configured to attain the maximum core speed? OS is XP SP3 clean install.
Thanks for any help,
Regards,
ThanimaiYou have to actually put quite some load to get the machine to work at its full throttle...while I'm typing this my ThinkPad is showing a core speed of 1199Mhz (it's a P4M 2.0) and trust you me, it would take quite a bit to get it up to the max, and your CPU is far newer and can take a lot more without shooting up...
Hope this helps.
Cheers,
George
In daily use: R60F, R500F, T61, T410
Collecting dust: T60
Enjoying retirement: A31p, T42p,
Non-ThinkPads: Panasonic CF-31 & CF-52, HP 8760W
Starting Thursday, 08/14/2014 I'll be away from the forums until further notice. Please do NOT send private messages since I won't be able to read them. Thank you. -
Set Maximum size for a subpanel created with splitter bars in LV8
Does anyone know how to set the Maximum size for a subpanel created with asplitter bar? If I show one cluster in the subpanel and use the scroll bar to scroll, I can see more (blank) area than I want. I just want the user to be able to scroll a cluster within a subpanel while the cluster is larger than the view area of the subpanel. I don't want to let the user scroll outside the cluster.
Ravi BeniwalI apologize for the mixup in terminology. Please read Pane wherever the word Subpanel was used.
Please see the attached VI for a description of my problem.
I would really appreciate any help with this.
Ravi Beniwal
Attachments:
Pane Scrolling Problem.vi 10 KB -
ISE 1.2 and maximum PSNs supported in my Persona config
Hello folks, I am putting together a medium to large distributed ISE deployment and wondered if anybody could tell me what the maximum number of PSNs are allowed under this configuration. I was reading thru an older training document with version 1.1 and it suggested only 5, which is why I am wondering if the specs changed on 1.2 but I cannot find them anywhere handy.
I have a large VM running the PRIMARY admin persona which also is secondary for my reporting & monitoring in my main data center.
In another state (connected with 10G) is another large VM acting as my secondary admin persona with primary monitoring & reporting.
Across multiple states I want to have multiple PSNs across the geographical layouts of each state but I am not sure if I can scale enough PSNs with my current version of 1.2 and my persona config listed above. I have a need for about 12 to 15 PSNs.
Wondering if I need two more VMs to break out my monitoring as one node in DC1 and secondary monitoring in DC2 in order to get more PSN scalability.
Any help would be greatly appreciated.
-ThanksAs Marvin suggested, I would look into using 1.3 at this point unless you have some specific concerns with that version and really want to stay with 1.2. With that being said, here are my recommendations/comments:
- Both v1.2 and v1.3 can actually scale up to 40 PSN nodes
- If any of your PSN nodes are going to be placed in the same location and are layer 2 adjacent I would recommend putting them in a node group and behind a load balancer. If you don't have a load balancer, I would still put them in a node group. At the moment a node group can have up to 10 PSNs
- If you are going to have 10-15 PSN nodes then you should dedicate 2 nodes for specifically for the monitoring persona
- The maximum roundtrip delay between any nodes cannot exceed 200ms
For more info you can always reference the "Network Deployment" section in the hardware installation guide for ISE:
v1.3
http://www.cisco.com/c/en/us/td/docs/security/ise/1-3/installation_guide/b_ise_InstallationGuide13/b_ise_InstallationGuide12_chapter_00.html
v1.2
http://www.cisco.com/c/en/us/td/docs/security/ise/1-2/installation_guide/ise_ig/ise_deploy.html
Thank you for rating helpful posts!
Maybe you are looking for
-
VersionMajor has incorrect value
Recently we have migrated from SAP 4. 7 to ECC6 , After migration the ABAP proxy interfaces are not working we get an error messages "XML tag Main/@versionMajor has incorrect value 002; expected value is 003" Any idea where to modify version major?
-
How can I unlock the remote desktop to shut down my MacBook Air?
My computer is locked as it says the Remote Desktop is attempting to reconnect and I can't get two other screens to close. Ctrl+Alt+ Delete is not working....
-
SRM 7 - Multiple POs from 1 Shopping Cart
Hi Everyone, Is it possible to create multiple POs from 1 shopping cart? 1st PO will have partial order qty and the second PO will have the remaining order quantity. Thanks.
-
Cannot open download link for Nokia Multimedia Tra...
Get the download page, the pop up opens, when I click on the Accept button - the site www.nmtapp.com will not open. Solved! Go to Solution.
-
How to do implement an Auto scrolling bar in Forms 9i
Hi,friends How can we implement a automatic scrolling bar when we edit item data in block which is so wide. I will be appreciated for your response,Thank you!! Pls give me some ideas Panzhen