Switched over to MGCP from H323, no incoming calls fast busy

Hello, I'm on the network side crossing over to the Voice side. We replaced a 3825 Voice Router at a branch office with a 2921. The 3825 was setup with a T1 and had a PRI connected to the FXO ports.  The 2921 is now connected via fiber and TAC helped get the router registered to the Call Manager. I'm trying to match up the old dial peers on the new router. I can't make out going or receive incoming calls, I get a This Call Can't be completed at this time.
When it was on the T1, the branch office was using H323. Now that's connects to the same CUCM, it's on MGCP. Shouldn't the old Dial Peers work on the new router?

I had to configure the FXO ports for the DN to route the incoming calls. I learned just because the Call Manager configured the Voice Gateway as a client, you still must configure the FXO ports to route the main DID to a DN on the LAN.
Great advice, learning alot about telephony and VoIP.
Wish I had more experience troubleshooting the CUCM and DID portion, also learned the phone compnay doesn't turn up their ISDN switch until you configure your PBX. And a PRI testing isn't the same as the data T1, it's about having the Signaling channel turned up and or configured.
Lessons learned, wished I would have crossed over to VoIP earlier.

Similar Messages

  • I recently switched over to Mail from Eudora

    I recently switched over to Mail from Eudora because of problems with Eudora and DSL that remain unresolved. However,I've run into an immediate problem.
    I retrieve mail from two locations: Home (DSL and now using Mail) and work (T1 and using Eudora). If I read, reply, and delete my mail from home, with Mail, when I next check my mail at work, all of that mail I've read and deleted appears. Mail seems not to be deleting anything off the actual mail servers. I've deleted, emptied trash, deleted trash, etc., but that mail isn't really gone, and that's not really helpful.
    Am I simply missing a setting somewhere? A box that has to be checked that says "Really, no kidding, delete the bleedin' mail"? This is not a problem I've encountered with said competing product.
    Thanks for all advice,
    GF

    If for a POP type account, go to Mail > Preferences > Accounts and under the Advanced tab for the account preferences, is Remove from server after retrieving a message selected and if so, what is your selection below for removing messages from the server?

  • I can send calls from Mac but incoming calls do not show up on Mac.

    Just downloaded Yosemite 10.10 on 10-21-14. I can make calls on my mac but unable to receive calls on my Mac. No notifications for incoming calls on my mac. Everything else runs fine. Messaging and calls from my mac works fine. I am running IOS 8.1 on a iPhone 4s. I have a 2009 Macbook Pro 2.54 duo with 8 gb of ram.

    There is no Adobe printer in recent versions of Mac OS. Look instead for a Save As Adobe PDF pull down.

  • A few months ago when I switched over to icloud from mobile me I set up my icloud with a new email address and now I can't get my calendars to sync with my iphone.  I can't cancel either account-the icloud or mobile me.

    Please help!  I have two separate email addresses -my old mobile me and the new icloud and now nothing is syncing with my iphone.  I'm not sure how to get everything back to syncing the way it was before I changed everything over to icloud. 

    If you really did migrate from MobileMe to iCloud, you would have the same address as before.
    It sounds as though you didn't actually migrate from MobileMe to iCloud, you just started up a brand new iCloud account.
    You won't be able to access MobileMe now. If you failed to move everything over to iCloud properly, then all the data and the account has been deleted as Apple said it would at the end of July.
    To get everything to sync, you need to make sure all your devices and computers are logged into the same iCloud account. Possibly what has happened is some are still using the old (now deleted) MobileMe account and some are using the new iCloud account.

  • If I switch over to Mac from PC will I be able to use my Quickbooks pc version or Adobe photoshop cs?

    Will Quickbooks pc versions work on Macs or will all my software have to be replaced? Will make the switch to Apple soon and trying to anticipate process. Also have Adobe photoshop CS and Quicken. Any suggestions or advice appreciated.

    Hello Herbert258,
    Short answer: No.
    Long answer: You have to buy the Mac versions for applications, kind of like Adobe Photoshop. If you want to keep your applications (and save some $$$) you can install Windows on Mac using boot camp. There are programs out there like Parallels where you can run windows on your desktop of your future Mac. You still need a copy of Windows to install, and Parallels is about $70.
    Best of luck,
    Sean

  • My phone is not switching from 4G over to WiFi. The phone has the network memorized its just not check marking the network and to switch over to WiFi. How can I fix this?

    I have the iPhone 4S and the wifi was working on it earlier yesterday. I noticed that the wifi didn't kick on last night. It has the network memorized so it could connect automatically. The network name pops up and there's a signal but the spinning circle thing is there and it won't put a check mark by the network name. The wifi will pop up every now and then but only stay for a minute or less. Everyone else's phone and computer is connecting just fine but mine isn't. It won't switch over to WiFi from 4G. I've tried turning off the wifi on my phone. I've tried to forget the network and put in the password numerous of times and I tried to fix it by turning my phone on and off and that still didn't work. I'm hoping that this is a temporary thing but I don't know. What's a good way to fix this because seriously I would like to not use up all of my data for this kind of bull crap. So what's a good way to fix this?

    I got the ATV hooked up to the WiFi after manually inputting the DHCP settings.
    The ATV will not see iTunes from a PC on the same iTune network.  I guess you need an Apple computer for iTunes to connect to the ATV.
    The biggest problem is that the iTunes store on the ATV is nonexistent I imagine because of competition/ monopolies in the UAE.  If I was in Lao, Burma, Thailand, Mozambique no problem.  40 Countries are listed and non of them are from the Middle East.  When I logon to the iTunes store on my PC it too does not allow for me to buy any movies or TV shows.  I am not sure why. 
    As for the iPad OS6, iTunes has an icon and when you click it you get iTune U or Podcast, no video content.  The App store works fine and they are always happy to take your money but no video content. 
    To top it all off YouTube is no longer licensed under OS6.0 and although I can get it on Google Chrome it is by no means as quick (for reasons unknown).
    As I said before if I choose United States as my country the ATV hooks up and lets me browse TV and movies and watch trailers but not able to purchase (obviously).
    So my conclusion is that ATV will not hook up to the iTune store in the UAE?  If this is incorrect please clue me in.

  • Service won't switch over

    I have a Treo 800w that I got a from a friend.
    I went online to the sprint website, and switched over my phone from the instinct.
    I did a hard reset on the treo, and after I set it up, it still won't work,
    and when I go to the phone preferences, I get the old owner's phone number under information 
    Post relates to: Treo 800w (Sprint)
    Post relates to: Treo 800w (Sprint)

    suggest to call sprint to get updated information about your account

  • Jabber call to voice mail fails with fast busy over VPN

    I have an issue that I ran into with CIPC phones over a VPN.  If a CIPC phone called over a VPN and started ringing a phone the call would fail with fast busy at the time the call would be forwarded to voicemail.  I found the issue was when remote the CIPC phone would negotiate the g.729 codec, when forwarded to a voicemail pilot over a SIP trunk set to g.711 the call would fail due to codec missmatch when no transcoders are present.
    So now I am running into what I believe to be the same issue with Jabber, when on premise the calls to voice mail work just fine, but when remote they fail.  I can directly call the voicemail pilot without error, but if calling a phone the call gets fast busy at the point we are forwarded to voicemail.  Even though all my regions are set to talk to all other regions on G.711 and the voicemail SIP trunk is set to G.711, I believe with the new features in CUCM9 that a lower speed codec has been negotiated since the we are going over the VPN, or Jabber has done this as it knows it's over VPN (not sure).  WIth CIPC I could go into the settings and turn off the Optimize for Bandwidth check box and the call would negotiate G.711.  With Jabber I can't find anything that would tell my Jabber client to stay on G.711 and I can only imagine this is a codec missmatch as the following are true.
    1. CIPC and Jabber share the same line
    2. VPN established and CIPC optimised for low bandwidth un-checked
    3. Over the same VPN the CIPC phone can leave a voicemail
    4. Over the same VPN the Jabber client gets fast busy once forwarded to voicemail
    5. Voicemail environment is Exchange-UM over SIP trunk
    6. SIP trunk is assigned a Device Pool, that is assigned to a region that all other regions communicate G.711 to
    7. On CIPC if optimised for low bandwidth is checked I get the exact same issue as I get with the Jabber client (fast busy when forwarded to voicemail)
    Would anyone know what I can do in CUCM 9 to fix this issue, as said no issue when all devices are on premise.  Wondering if there is a service parameter or a way to change the codec selection so the Jabber client attempts to always negotiate G.711.  The correct answer would be to get some PVDM DSP resources and kick up a transcoder in my resource group, and that may be what I talk them into doing if I have no other options.                  

    We have been getting the exact same thing for almost a year now... since switching to FiOS Digital Voice in May of last year!  Every time I call in to report it they 'escalate' the issue but it never gets resolved.  The problem seems to be in the initial connection.  Most of the time it works fine but, several times a month, after I call to get messages and it starts to play the new message it goes dead and I get the busy signal.  I get the same message when I call back:  “I’m sorry – that account is in use at this time.  Please try again later!”  I have even called in with my cell phone and get the same message!  I HAVE EVEN used the Internet to see if I could get my messages and, when I hit Play, I get a pop-up saying: “Your Voice Mail box is currently in being accessed; please try again later.  If the problem continues, please contact our Customer Support Center at 1-888-553-1555. We apologize for any inconvenience.”  This is obviously a software bug that Verizon has no clue on how to troubleshoot OR fix!!!  I wonder how many people have the problem and just don’t bother reporting it because of the hassle?  When it first started happening they destroyed my entire mailbox and I had to re-enter the complete mailbox setup again – 3 times!!!  NEVER let them talk you into that!!!  It’s their problem and they need to fix it!!!!!!!  I wish I could go back to the ‘normal’ voicemail we originally had… they want hundred$ to switch back because I’d be breaking my #$@%^&* contract!  Good luck if you have Verizon………

  • Linksys SPA3102, busy line on incoming calls

    Hi there,
    I'm trying to set this device up in this specific scenario:
    - PSTN: 1st incoming call, the user gets it.
    - PSTN: 2nd incoming call, but the 1st call is still ongoing.
    Actual result: 2nd incoming call obtains ring tones, and he/she thinks there is nobody home
    Desired result: 2nd incoming call obtains busy line tone, and he/she thinks there is somebody home and is busy
    Is this device able to do this?, any tip about which configuration parameter should I change?
    Many thanks, Ibon.

    Sorry, wrong forum
    Posting in the right one

  • HT5824 I switched over from an iPhone to a Samsung Galaxy S3 & I haven't been able to receive any text messages from iPhones. Please help with turning my iMessage completely off..

    I switched over from an iPhone to a Samsung Galaxy S3 & I haven't been able to receive any text messages from iPhones. I have no problem sending the text messages but I'm not receivng any from iPhones at all. It has been about a week now that I'm having this problem. I've already tried fixing it myself and I also went into the sprint store, they tried everything as well. My last option was to contact Apple directly. Please help with turning my iMessage completely off so that I can receive my texts.

    If you registered your iPhone with Apple using a support profile, try going to https://supportprofile.apple.com/MySupportProfile.do and unregistering it.  Also, try changing the password associated with the Apple ID that you were using for iMessage.

  • I was forced to switch from my original computer to a new one and majority of my iTunes were switched over but my audiobooks did not. Is there any way that I can retrieve them again?

    I was forced to switch from my original computer to a new one and majority of my iTunes were switched over but my audiobooks did not. Is there any way that I can retrieve them again. If I go to attempt to rebuy it, then it says thhat I technically already bought it but it won't download.

    Audiobooks are not available for redownloading, so you need to transfer them from your old computer, or get them from your backup. How did you copy your iTunes contact from your old computer to our new one?
    Regards.

  • My Verizon wireless service at my house has begun to degrade over the last 6 Month.  It has begun to be very frustrating seeing how we switched over from Satellite to Verizon 4GLTE wireless device.  How do I contact someone to see what the issue may be. Z

    My Verizon wireless service at my house has begun to degrade over the last 6 Month.  It has begun to be very frustrating seeing how we switched over from Satellite to Verizon 4GLTE wireless device.  How do I contact someone to see what the issue may be. Zip Code 22580.

    Out of curiosity how much data per month are you using?  Another factor could be if neighbors have all done the same thing as you and the node is being overloaded on home internet use.

  • Switch over from active to passive in the cluster

    If online EMS Sun Server goes off line , the client looses the connectivity with EMS till the IP address of the other online server is updated in client PC.
    When the servers switch over from active to passive in the cluster, we have to change the server IP settings at the client PC manually. Since both the active as well as the passive servers will be pinging, we are not in a position to identify the active/passive servers, so automatic server setting is not possible at the client.
    How to find out the solution for which server is active when the swich over is happend.

    Hi Kristoffer,
    remember to click on enable schedule when you schedule a package.
    To know if a scheduled package is ok you can see first if present in the tblschedule of your appset and also if present in the windows task schedulerif with status "ready".
    After you just have to check the view status if you found the package execution completed you're sure it's running. " version at the same time can cause issues also with different packages better to schedule with a sufficient delay to be sure that the first has ended, in your case 1 package is ok.
    I would delete the 2 packages from bpc, checking also the windows scheduler to be sure that no packages are running and rebuild one from scratch setting repeat every 4 hours and checking "enable schedule".
    Regards
         Roberto

  • I recently switched over from Apple to Sony and I would like to know how I can change my settings so that all my iCloud emails are forwarded to my Gmail account?

    I recently switched over from Apple to Sony and I would like to know how I can change my settings so that all my iCloud emails are forwarded to my Gmail account?

    Log in on iCloud.com and go to Mail. In Mail, at the bottom left you should see a gear icon. Click on it, go to Settings (or Preferences, I'm doing this from memory), and in there you'll find an option to forward your iCloud email to another service.

  • Switch over from taxinj to taxinn

    how to switch over from taxinj 4.7 version to eec6.0, to switch over from taxinj to taxinn, from business data point of view before cutover strategy , what are the things take into consideration , if taxcodes will overlap, with taxinn .
    what are the thigs take as precautions.
    waiting for ur response. thank you

    When you are switching fron TAXINJ to TAXINN, WRT Tax Codes, it is recommended to maintain new Tax Codes for TAXINN, as TAXINJ follows formula based calculation & TAXINN follows Condirtion based calculation.
    Regards,
    Rajesh Banka
    Reward points if helpful.

Maybe you are looking for