The same network and id vlan in different contex in the same ACE
Hello,
I want to know if I can create 2 context in an ACE with the same ID Vlans that other context and this can be in the same network, in the configuration I explain.
Best Regards
++++++++Switch C6513++++++++
svclc multiple-vlan-interfaces
svclc module 6 vlan-group 100
svclc module vlan-group 100 60,233
vlan 60
name inside
vlan 233
name outside
interface vlan 233
ip address 10.24.16.1 255.255.255.0
no shutdown
++++++++Context Admin++++++++
hostname ACE-MOD6
ft interface vlan 350
ip address 10.24.15.34 255.255.255.248
peer ip address 10.24.15.33 255.255.255.248
no shutdown
ft peer 1
heartbeat interval 200
heartbeat count 20
ft-interface vlan 350
ft group 1
peer 1
priority 200
peer priority 150
associate-context Admin
inservice
context SERV1
description SERV1
allocate-interface vlan 60
allocate-interface vlan 233
context SERV2
description SERV2
allocate-interface vlan 60
allocate-interface vlan 233
ft group 2
peer 1
priority 200
peer priority 150
associate-context SERV1
inservice
ft group 3
peer 1
priority 150
peer priority 200
associate-context SERV2
inservice
++++++Contex SERV1++++++
interface vlan 60
ip address 10.24.8.5 255.255.255.0
no shutdown
interface vlan 233
ip address 10.24.16.5 255.255.255.0
no shutdown
ip route 0.0.0.0 0.0.0.0 10.24.16.1
++++++Contex SERV2++++++
interface vlan 60
ip address 10.24.8.6 255.255.255.0
no shutdown
interface vlan 233
ip address 10.24.16.6 255.255.255.0
no shutdown
ip route 0.0.0.0 0.0.0.0 10.24.16.1
Sharing Vlans is possible in routed mode.
Its not possible when ACE is operating in Bridge mode.
You need to use unique IP addresses in each context for shared vlans.
Also make sure to use " shared-vlan-hostid " command.
When contexts share a VLAN, the ACE assigns a different MAC address to the VLAN on each context. The MAC addresses reserved for shared VLANs are 0x001243dc6b00 to 0x001243dcaaff, inclusive. All ACE modules derive these addresses from a global pool of 16k MAC addresses. This pool is divided into 16 banks, each containing 1,024 addresses. An ACE supports only 1,024 shared VLANs, and would use only one bank of MAC addresses out of the pool.
By default, the bank of MAC addresses that the ACE uses is randomly selected at boot time. However, if you configure two ACE modules in the same Layer 2 network and they are using shared VLANs, the ACEs may select the same address bank and use the same MAC addresses. To avoid this conflict, you need to configure the bank that the ACEs will use. "
Above paragraph & More details at
http://www.cisco.com/en/US/docs/interfaces_modules/services_modules/ace/v3.00_A2/command/reference/config.html#wp1447465
Syed Iftekhar Ahmed
Similar Messages
-
I upgraded from ios 4.3.3 to ios 7, but during the final setup I input the language (english) and try to connect with my wifi and I get the message unable to join my home network. How can I get past this so I can complete the setup?
Are you using the encryption key code for your home wifi network? The encryption key code is usually located on a sticker on the back of the router.
-
I installed Lion on my Mac Pro laptop. Regarding Time Capsul - I get a messaage as follows: couldn't complete backup due to a network problem. Make sure your computer and back up disk are on the same network and that the backup disk is turned on. Then try again to back up. I have time capsul turned on. bill
I have exactly same problem with my MBP and MBA, after upgrading to Lion. I've tried to fix this issue while cheking key chain issues and network setup, even formating hdd and time capsule firmware upgrade (ver. 7.6.1.). Nothing can help. It is very annoying.
-
How to I share Itune library, and movies with a different user on the same computer?
How do I share Itunes and movies with a different user on the same computer?
https://discussions.apple.com/community/itunes
-
iOS 5 used to allow Airplay between iPad (WiFi) and Apple TV (Ethernet) as long as they were on the same network, i.e. connected to the same wired/wireless router. In iOS 6, now both the iPad and the Apple TV have to be on the same network and both have to be connected using WiFi ? Why did they change this ? Means that the iPad and the Apple TV box both have to be in range of the wireless router when this wasn't a restriction before. Apple TV could be anywhere as long as it was connected to the same wireless router via ethernet cable. Seems like an unnecessary thing to restrict.
I have found with AppleTV that it is the IPV6 on the computer you want to access is the problem. The issue is that Homegroup on Win 7 or Win 8 requires IPV6 to work, but AppleTV won't work with IPV6. (So maybe double check you have IPV6 turned off)
So you have to make a choice - Homegroup or AppleTV.... but you can't have both, until Apple brings ATV up to date. (crazy that it does not recognise IPV6 - c'mon Apple!)
You can set up sharing individually in Win 7 or 8 and have the ATV access files that way.
Having said that, there is always the exception.. I have an old HP home server running Win8 and it services ATV - but is part of the Homegroup... have no idea why it works on both, but no other machine on the home network will talk to both ATV and Homegroup at the same time! -
Who can shed some light on my ongoing connection problem.
After upgrading my iPad Air with IOS 7.06, I could no longer connect to the internet.
I have 2 MacBooks Air, 1 ipad mini and one iPhone 4S running on the same network, and they are all connected to the net and function well.
So I cleaned up the ipad completely, installed the latest firmware and reinstalled my apps : no connection.
I tried all things of resets and forgets. No result.
I have been fondling with my Airport Extreme 5 , but that did not help much.
This morning I went to a neighbor , hooked my ipad air on his network, typed the password and the thing all worked fine.
I have tried to connect the ipad air as an ethernet client, but that did not work. „Not enough power“ was the statement
Ideas anyone ?Yes I tried this manyfold. But did not work. Reading on, I took Tesserac's advice. Shut down router and computer.
Start router after 15 minutes and wait another 10 minutes before starting the computer.
Et voila.... everything is back in working order,
Regards form Curacao, Dutch Caribean.
Pete van Linden -
My ipad mini is not connecting to the wifi network. I have the correct network and password chosen, but the message I get is that "unable to join". I have reset my ipad and it still says the same thing. What can I do about this?
Hey Dr kris,
Thanks for the question, and welcome to Apple Support Communities.
I understand that you are having issues connecting to Wi-Fi networks with your iPad mini. The following troubleshooting assistant may lead to a resolution:
Apple - Support - iPhone - Join a network Assistant
http://www.apple.com/support/iphone/assistant/wifi/
For more in-depth troubleshooting, refer to the following article (refer to the "Unable to connect to a Wi-Fi network):
iOS: Troubleshooting Wi-Fi networks and connections
http://support.apple.com/kb/TS1398
Thanks,
Matt M. -
I have a Mac on my home network and also a Systemline music server on same network. My PC was able to find the server but my MAC cannot. I can ping the server from the mac, but cannot actually connect . Also can't add the mac as a location from server, despite following the Systemline instructions that impy this can be done.
Can anyone please advise what I am doing wrong?Hi LowLuster
Thanks for reply. I am not an expert on these sharing protocols but I think I have turned on SMB sharing but still wont connect. I tried adding netwrik drive by using cntrl K in finder and using smb\\network address but nothing. It is driving me mad!! -
I cannot connect my Macbook to Epson printer XP 400. Both are on the same network and Symantic anti virus is disconneted.
Add printer does not find the Epson. All works when I use the USB cable.Further information on my question about the epson wireless printer and macbook.
It seems that the epson xp-400 works wirelessly only with 802.11n wireless network not with 802.11g or earlier.
Does anyone else know about this. I read it on the epson support site for epson xp-400.
Also epson xp-400 will not work wirelessly if it is already connected to a computer with a USB cable. -
i have a late 2011 macbook pro and i don't have the airplay icon on my menu. Everything is on the same network and i have a black mini apple Tv. it is either 2nd or 3rd generation. The airplay icon comes up in itunes it doesn't works with video just music. I want to mirror it on my apple tv. Will you please help me?
That's why, you will need to upgrade to 10.8
-
Successfully set up TC (the latest one) for MBP. I can access to TC wirelessly. Tried to access from my PC too but PC does not even detect TC (as storage), while PC is connected in the same network and can access to the internet. Anything missed?
Load the airport utility for windows.. it has several parts.. the key one is bonjour for windows which helps windows find apple network devices.
The TC should also be setup with names that windows can use.. ie short, no spaces and pure alphanumeric.
So Fred Blog's Airport Time Capsule
Is not a valid windows name.
TCgen5 is. -
Can I use my old apple tv and new apple tv together on the same network and with the same tv
Can I use my old apple tv and new apple tv together on the same network and with the same tv???
Welcome to the Apple Community.
Yes. -
Can I connect two apple tv on same network and same apple ID at a time ?
Can I connect two apple tv on same network and same apple ID at a time ?
Welcome to the Discussion Forums.
Yes you can do all that without needing to keep plugging things in and out. You will still need to manually turn on the receiver and turn down the volume from the tv though. -
Management and native Vlan in different subnet??
Can i have a management ip and native vlan in different subnet on a AIR-1242 and 2960 switch?
Native on Switch = 1.
Interface vlan 100 = 10.10.1.25X /24
BVI ip in vlan 100 = 10.10.1.25X /24
-HM-Hi,
Thanks for the update..
Ok in short YES this can be done.. here is the AP configuration..
Step 1>> Configure the SSID and map it with respective Vlans..
Step 2>> Create the sub interafce int dot11 0.5 / int fa 0.5 (encapsulation dot1q 5 , bridge-group 5)and int dot11 0.6 / int fa 0.6(encapsulation dot1q 6 , bridge-group 6)
Step 3>> Create the sub interface 0.100 for both Radio and Fa and under this (encapsulation dot1q 100 native , bridge-group 1)
Step 4>> Make sure all the interafces are up and running and Try to ping the VLAN 100 interafce ip addr from the AP to verify.
lemme know if this answered your question..
Regards
Surendra
====
Please dont forget to rate the posts which answered your question and mark it as answered or was helpfull -
i tried to download the new itunes and i keep getting a message that "the feature i am trying to use its on a network resource that is unavailable
Which particular .msi file does the message go on to say can't be found? (Several different .msi files can be mentioned in this context: itunes.msi, bonjour.msi, AppleSoftwareUpdate.msi, etc.)
Maybe you are looking for
-
Hello There, I have written an Outlook Add-In to add several User Properties to our incoming emails. This add-in will be installed in 100 computers in different states and our Exchange server is hosted in our datacenter in CA. Everything works great
-
Not able to post document using BAPI_ACC_GL_POSTING_POST
Hi all, While trying to post documents in FB60 using BAPI_ACC_GL_POSTING_POST we are getting error Account not assigned to company code. But we are able to post documents manually using the same account and company code. Couls any one help me out to
-
How to display XML file that XI sent to my j2ee appl?
Hi, In my scenario File->XI->J2EE appl. I got XML page cannot be displayed. XML document must have a top level element. Error processing resource 'http://localhost:7001/Invoke/DisplayRes'. I deployed my .ear file on BEA Weblogic application server9.0
-
Information about MY BT site login
Hi there, I recently signed up to BT for my Broadband and Phone (went active on Wednesday). I have a general query in regards to the MY BT site, which according to the welcome letter allows me to check my bills online and various other things like em
-
Volume bar won't appear.
Hi, My volume bar used to appear when I pressed the buttons on my keyboard, but now it doesn't. The volume will still go up or down I just would like to see it on the screen like I used to be able to. I tried reinstalling HP Mediasmart Smartmenu and