The version of this vi downloaded on the target does not match the version you have in the project

I am using Labview 8.6 and field point cFP-2220
I have a project that have some VIs running on the development computer and some VIs running on the field point (one top level VI and a few sub Vis).
When I run the program every thing is working, I disconnect from the field point, still every things is running; however when I reconnect I get the error above.
For FP Write(float-IO).vi and FP Write(Boolean-IO)
error message attached. Any help will be greatly appreciated.
Thanks.
Attachments:
error.JPG ‏42 KB

I am having this same issue, but am running LV2010. The conflict, for me, is always with NI_LVConfig.lvlib
If I hit the Apply button, the code deploys and runs on my cFP-2120 without issue. I disconnect from the target in Project Explorer, reconnect without any code changes and I get the same Conflict Resolution popup.
The code I ran on my RT target was a Get Date/Time in Seconds writing to an indicator - that's it.

Similar Messages

TS3212 I continue to try to install iTunes; when I attempt to open the newly installed iTunes, I receive errors that it was not correctly installed. I have followed the direction on this website, but I face the same error. Please help.

I continue to try to install iTunes; when I attempt to open the newly installed iTunes, I receive errors that it was not correctly installed. I have followed the direction on this website, but I face the same error. Please help.

latest message indicates I need Apple Application Update
With the Error 2, let's try a standalone Apple Application Support install. It still might not install, but fingers crossed any error messages will give us a better idea of the underlying cause of the issue.
Download and save a copy of the iTunesSetup.exe (or iTunes64setup.exe) installer file to your hard drive:
http://www.apple.com/itunes/download/
Download and install the free trial version of WinRAR:
http://www.rarlab.com/download.htm
Right-click the iTunesSetup.exe (or iTunes64Setup.exe), and select "Extract to iTunesSetup" (or "Extract to iTunes64Setup"). WinRAR will expand the contents of the file into a folder called "iTunesSetup" (or "iTunes64Setup").
Go into the folder and doubleclick the AppleApplicationSupport.msi to do a standalone AAS install.
Does it install properly for you?
If instead you get an error message during the install, let us know what it says. (Precise text, please.)

The document "PP_CS_Higher Education_USA_V1" is on a volume that does not support permanent version storage.

The document “PP_CS_Higher Education_USA_V1” is on a volume that does not support permanent version storage. Not sure what this means exactly.
Any thoughts out there?

This error is is usually encountered when trying to update a file that has been opened from a CD or DVD disc.
Move the file to the desktop before you open it.
Where is this file stored, a CD or DVD, external hard drive, USB memory ?

HT204135 I update my Mac to version 10.9.2 and now my printer does not work anymore. I did all the software updates and I do not understand why my mac does not recognize the printer anymore?

I update my Mac to version 10.9.2 and now my printer does not work anymore. I did all the software updates and I do not understand why my mac does not recognize the printer anymore?

Go to the website of the manufacturer of your printer and check to see if they have released an updated driver for your particular model.

The located assembly's manifest definition with name 'openfoundation' does not match the assembly re

Ok. been working on this for the better part of a day. I am having trouble with the .net web controls. trying to create a simple portlet that populates a text box with values from a 2nd text box when a button is selected. both text boxes are in the same portlet.
without using the <httpModules> entry in the web.config file the portlet works fine, but it does pop you out of the portal.
setup: working in a Dev. environment with portal and portlets on the same box.Portal version is 5.0.2.EDK version is 5.0.2.
error:
The located assembly's manifest definition with name 'openfoundation' does not match the assembly reference.Description: An unhandled exception occurred during the execution of the current web request. Please review the stack trace for more information about the error and where it originated in the code. Exception Details: System.IO.FileLoadException: The located assembly's manifest definition with name 'openfoundation' does not match the assembly reference.Source Error:An unhandled exception was generated during the execution of the current web request. Information regarding the origin and location of the exception can be identified using the exception stack trace below.Assembly Load Trace:The following information can be helpful to determine why the assembly 'openfoundation' could not be loaded.=== Pre-bind state information ===
LOG: DisplayName = openfoundation, Version=2.0.9.3152, Culture=neutral, PublicKeyToken=d0e882dd51ca12c5
(Fully-specified)
LOG: Appbase = file:///c:/inetpub/wwwroot/netTest
LOG: Initial PrivatePath = bin
Calling assembly : dotnetportlet, Version=3.5.0.1, Culture=neutral, PublicKeyToken=null.
===
LOG: Publisher policy file is not found.
LOG: No redirect found in host configuration file (C:\WINNT\Microsoft.NET\Framework\v1.1.4322\aspnet.config).
LOG: Using machine configuration file from C:\WINNT\Microsoft.NET\Framework\v1.1.4322\config\machine.config.
LOG: Post-policy reference: openfoundation, Version=2.0.9.3152, Culture=neutral, PublicKeyToken=d0e882dd51ca12c5
LOG: Attempting download of new URL file:///C:/WINNT/Microsoft.NET/Framework/v1.1.4322/Temporary ASP.NET Files/nettest/9e6689f5/a0d2f067/openfoundation.DLL.
LOG: Attempting download of new URL file:///C:/WINNT/Microsoft.NET/Framework/v1.1.4322/Temporary ASP.NET Files/nettest/9e6689f5/a0d2f067/openfoundation/openfoundation.DLL.
LOG: Attempting download of new URL file:///c:/inetpub/wwwroot/netTest/bin/openfoundation.DLL.
WRN: Comparing the assembly name resulted in the mismatch: Minor Version
Stack Trace:[FileLoadException: The located assembly's manifest definition with name 'openfoundation' does not match the assembly reference.]
 Plumtree.Remote.Portlet.PortletContextFactory.CreatePortletContext(HttpRequest req, HttpResponse resp) +0
 Com.Plumtree.Remote.Transformer.Condition.GatewayedStandardCondition.UseFilter(HttpContext ctx)
 Com.Plumtree.Remote.Transformer.FilterManager.UpdateFilter(HttpContext ctx)
 Com.Plumtree.Remote.Transformer.PTTransformer.BeginRequestHandler(Object sender, EventArgs e)
 System.Web.SyncEventExecutionStep.System.Web.HttpApplication+IExecutionStep.Execute() +60
 System.Web.HttpApplication.ExecuteStep(IExecutionStep step, Boolean& completedSynchronously) +87
Version Information: Microsoft .NET Framework Version:1.1.4322.573; ASP.NET Version:1.1.4322.947
************************************************************Is there any step by step instructions for setting up and using the .net web controls in Plumtree????
There doesn't seem to be any information in one spot as to setting up the environment to use the .Net Web Controls. I have had to piece together information from multipule threads to get this far. I.E. there was nothing in any documentation that I have read that required the installation of the VJ# lib's. (that error took me the first half of the day to resolve :-) )
Thanks for any help,
Greg************************************************************

Also, when reviewing the Plumtree_.NET_Web_Controls_InstallLog.log there were 5 nonfatal erros. These error's were:
Install File: E:\plumtree\ptwc\2.0\bin\assemblies\edk.dll Status: ERROR Additional Notes: ERROR - java.io.FileNotFoundException: E:\plumtree\ptwc\2.0\bin\assemblies\edk.dll (The process cannot access the file because it is being used by another process)
Install File: E:\plumtree\ptwc\2.0\bin\assemblies\jsregistry.dll Status: ERROR Additional Notes: ERROR - java.io.FileNotFoundException: E:\plumtree\ptwc\2.0\bin\assemblies\jsregistry.dll (The process cannot access the file because it is being used by another process)
Install File: E:\plumtree\ptwc\2.0\bin\assemblies\log4net.dll Status: ERROR Additional Notes: ERROR - java.io.FileNotFoundException: E:\plumtree\ptwc\2.0\bin\assemblies\log4net.dll (The process cannot access the file because it is being used by another process)
Install File: E:\plumtree\ptwc\2.0\bin\assemblies\openfoundation.dll Status: ERROR Additional Notes: ERROR - java.io.FileNotFoundException: E:\plumtree\ptwc\2.0\bin\assemblies\openfoundation.dll (The process cannot access the file because it is being used by another process)
Install File: E:\plumtree\ptwc\2.0\bin\assemblies\Plumtree.WCFilter.dll Status: ERROR Additional Notes: ERROR - java.io.FileNotFoundException: E:\plumtree\ptwc\2.0\bin\assemblies\Plumtree.WCFilter.dll (The process cannot access the file because it is being used by another process)
When installing the Web Control's do you need to stop any services? I didn't see anything in the install notes about doing this?

Pretzel: The located assembly's manifest definition with name 'openfoundation' does not match the

We have got 5.0.2 Plumtree portal, EDK 5.0.2 and .Net Web Controls 2.1.
I am trying to call:
IPortletContext oPortletContext = PortletContextFactory.CreatePortletContext(System.Web.HttpContext.Current.Request, System.Web.HttpContext.Current.Response);
I have attached the error I am getting. Is this related to Open Foundation version? This is quite urgent because we are in the process of trying to get a demo together for grabbing Activity Rights.
Server Error in '/portlets/DOJ/JNET/pretzel.clients.doj.reentry' Application.
The located assembly's manifest definition with name 'openfoundation' does not match the assembly reference.Description: An unhandled exception occurred during the execution of the current web request. Please review the stack trace for more information about the error and where it originated in the code. Exception Details: System.IO.FileLoadException: The located assembly's manifest definition with name 'openfoundation' does not match the assembly reference.Source Error:An unhandled exception was generated during the execution of the current web request. Information regarding the origin and location of the exception can be identified using the exception stack trace below.Assembly Load Trace:The following information can be helpful to determine why the assembly 'openfoundation' could not be loaded.=== Pre-bind state information ===
LOG: DisplayName = openfoundation, Version=2.0.9.8318, Culture=neutral, PublicKeyToken=d0e882dd51ca12c5
(Fully-specified)
LOG: Appbase = file:///E:/Data/HSTPRDAPP01/Inetpub/plumtree/portlets/DOJ/JNET/pretzel.clients.doj.reentry
LOG: Initial PrivatePath = bin
Calling assembly : dotnetportlet, Version=3.5.0.1, Culture=neutral, PublicKeyToken=null.
===
LOG: Publisher policy file is not found.
LOG: No redirect found in host configuration file (C:\WINNT\Microsoft.NET\Framework\v1.1.4322\aspnet.config).
LOG: Using machine configuration file from C:\WINNT\Microsoft.NET\Framework\v1.1.4322\config\machine.config.
LOG: Post-policy reference: openfoundation, Version=2.0.9.8318, Culture=neutral, PublicKeyToken=d0e882dd51ca12c5
LOG: Attempting download of new URL file:///C:/WINNT/Microsoft.NET/Framework/v1.1.4322/Temporary ASP.NET Files/portlets_doj_jnet_pretzel.clients.doj.reentry/26128f6f/cfc1837a/openfoundation.DLL.
LOG: Attempting download of new URL file:///C:/WINNT/Microsoft.NET/Framework/v1.1.4322/Temporary ASP.NET Files/portlets_doj_jnet_pretzel.clients.doj.reentry/26128f6f/cfc1837a/openfoundation/openfoundation.DLL.
LOG: Attempting download of new URL file:///E:/Data/HSTPRDAPP01/Inetpub/plumtree/portlets/DOJ/JNET/pretzel.clients.doj.reentry/bin/openfoundation.DLL.
WRN: Comparing the assembly name resulted in the mismatch: Minor Version
Stack Trace:[FileLoadException: The located assembly's manifest definition with name 'openfoundation' does not match the assembly reference.]
   Plumtree.Remote.Portlet.PortletContextFactory.CreatePortletContext(HttpRequest req, HttpResponse resp) +0
   pretzel.clients.doj.reentry.navigation.Page_Load(Object sender, EventArgs e) in \\devnet2\inetpub\doj\reentry\development\pretzel.clients.doj.reentry\navigation.aspx.cs:22
   System.Web.UI.Control.OnLoad(EventArgs e) +67
   System.Web.UI.Control.LoadRecursive() +35
   System.Web.UI.Page.ProcessRequestMain() +750
Version Information: Microsoft .NET Framework Version:1.1.4322.1031; ASP.NET Version:1.1.4322.947

I have seen this before after a upgrade of the EDK, found I had to remove the reference in the C# project to the old EDK dll and re add it to the new EDK dll.
Also noticed that you are using the System.Web.HttpContext.Current fully qualified namespace in the CreatePortletContext() call instead of the usual way of PortletContextFactory.CreatePortletContext(Request, Response) this uses the System.Web.HttpRequest.Page namespace by default.

AP is unable to associate. The Regulatory Domain '-E' configured on interface '802.11a' does not match the Controller Regulatory Domain '-C'

Hi,
There are three different types of APs associated with controller and working fine.
1.       AIR-LAP1252AG-E-K9
2.       AIR-LAP1522AG-E-K9
3.       AIR-CAP1552E-C-K9
WLC is AIR-CT5508-K9. Software version is 7.4.100.0. Field Recovery Image is 7.0.112.21. Firmware version is FPGA 1.7, Env 1.8, USB console 2.2. WCS is 7.0.240.0 for Windows.
WCS is sending alarms for AIR-LAP1522AG-E-K9:
Message: AP is unable to associate. The Regulatory Domain '-E' configured on interface '802.11a' does not match the Controller Regulatory Domain '-C'.
Before Controller was 7.2.4 (not sure).
Country configured on WLC is AE and shows -CE regulatory domain. Mesh APs are also associated.
I believe this Critical alarm should not come.
how much is this alarm important? What should be done to resolve this?

Typically you still need to make sure that the country codes are indeed configured on the WLC. Thing can change when you upgrade code as standards might of changed and regulations also. If your AP's are functional, then you should be okay and I wouldn't worry too much about it, but if after the upgrade, the WLC complains about country code stuff, then you just need to verify that the AP's country code is defined on the WLC. May times the AP will not join and if it does join, the radios might be disabled or in a down status.
Sent from Cisco Technical Support iPad App

I have an ExportPDF subscription under an old account for which the email does not exist anymore and I have forgotten the password. Therefore I cannot reset the password. I hav created a new Adobe account so how do I get the subscription for ExportPDF m

I have an ExportPDF subscription under an old account for which the email does not exist anymore and I have forgotten the password. Therefore I cannot reset the password. I have created a new Adobe account so how do I get the subscription for ExportPDF moved to the new account?

Hi lgmmo,
I think your best best to get this resolved is to contact Adobe Customer Care. Here's the contact info: Contact Customer Care.
A quick Chat session should get you fixed up.
Please let us know if you have additional questions.
Best,
Sara

Invalid application descriptor: descriptor version does not match runtime version

Hi.
I have writen a very simple AIR app. Its not really an app
just a button on the stage in flex2 as I want to try packaging it
up as an air app from the command line. When i use adl to do this i
get the following error.
invalid application descriptor: descriptor version does not
match runtime version
I have just downloaded the latest version of AIR 1.0.1 and
still have no joy even when i change <application xmlns="
http://ns.adobe.com/air/application/1.0">
to <application xmlns="
http://ns.adobe.com/air/application/1.0.1">
The code for my app is below, i woudl very much appreciate a
little advice as to where i am going wrong.
Many thanks
Barry.
test-app.xml (descriptor file)
<?xml version="1.0" encoding="UTF-8"?>
<application xmlns="
http://ns.adobe.com/air/application/1.0.1">


<id>test application</id>

<filename>test</filename>

<name>test app</name>

<version>v1</version>





<initialWindow>


<content>test.swf</content>


























</initialWindow>


























</application>
test.mxml
<?xml version="1.0" encoding="utf-8"?>
<mx:Application xmlns:mx="
http://www.adobe.com/2006/mxml"
layout="absolute">
<mx:Button x="201" y="167" label="Hello AIR!"/>
</mx:Application>

My descriptor version was 1.5.2
(see line <application xmlns="http://ns.adobe.com/air/application/1.5.2"> in file appName-app.xml)
My Flex sdk was 3.2 (see Project->Properties->Flex Compiler->Flex SDK Version)
To support air debugger (adl) version 1.5.2, sdk 3.2 was too old, so i got this same error
so i switched to sdk 3.4 (free download at adobe.com)
and the problem was solved

V5R4M5 does not match InfoAPAR version V5R4M0, import error

Hi All,
We found following warning when PTF check in ECC6sr3 sapinst on v5r4
WARNING: The OS/400 version V5R4M5 does not match InfoAPAR version V5R4M0.
ok Product ID: 5722SS1 - PTF ID: SI22389 - Status: NOT UP TO DATE
ok Product ID: 5722999 - PTF ID: TL07282 - Status: NOT UP TO DATE
CUMPKG
ok Product ID: 5722999 - PTF ID: MF42358 - Status: NOT UP TO DATE
ok Product ID: 5722999 - PTF ID: MF42518 - Status: NOT UP TO DATE
ok Product ID: 5722999 - PTF ID: MF42529 - Status: NOT UP TO DATE
ok Product ID: 5722999 - PTF ID: MF42394 - Status: NOT UP TO DATE
ok Product ID: 5722999 - PTF ID: MF42393 - Status: NOT UP TO DATE
ok Product ID: 5722999 - PTF ID: MF42258 - Status: NOT UP TO DATE
ok Product ID: 5722999 - PTF ID: MF42043 - Status: NOT UP TO DATE
ok Product ID: 5722999 - PTF ID: MF42042 - Status: NOT UP TO DATE
ok Product ID: 5722999 - PTF ID: MF41883 - Status: NOT UP TO DATE
   23 PTFs checked.        11 missing PTFs detected.
The microcode is M5 however OS is M0. We also got similar warning in other host with 2 missing PTFs and SAP installation can successfully completed. But with this M5 host always warns with TL07282 missing (however TL57282 existed)
we checked APAR recomendation for v5r4m5 from IBM, products, and sysval, tmksvrpatch, all are sufficient only this PTF check from SAPinst. When we continue, the import processes are failed
(DB) ERROR: DDL statement failed
(CREATE TABLE "DDNTF_CONV_UC" ( "TABNAME" GRAPHIC(30) CCSID 13488 DEFAULT ' ' NOT NULL , "BLOCKNR" SMALLINT DEFAULT 0 NOT NULL , "FIELDSLG" DECIMAL(5,0) DEFAULT 0 NOT NULL , "FIELDS" BLOB(32600) ) )
DbSlExecute: rc = 99
(SQL error -901)
error message returned by DbSl:
SQL system error. MSGID= Job=009618/SAPINST/QJVAEXEC
(IMP) ERROR: DbSlPrepare/BegModify failed
rc = 103, table "DDNTF_CONV_UC"
(SQL error 204)
error message returned by DbSl:
DDNTF_CONV_UC in R3ECDDATA type *FILE not found. MSGID= Job=009618/SAPINST/QJVAEXEC
TRACE: 2008-09-10 11:14:29 com.sap.inst.migmon.LoadTask processPackage
Loading of 'SAPNTAB' import package into database:
/usr/sap/ECD/SYS/exe/run/R3load -i SAPNTAB.cmd -dbcodepage 4102 -l SAPNTAB.log -nojournal
ERROR: 2008-09-10 11:14:32 com.sap.inst.migmon.LoadTask run
Loading of 'SAPNTAB' import package is interrupted with R3load error.
Process '/usr/sap/ECD/SYS/exe/run/R3load -i SAPNTAB.cmd -dbcodepage 4102 -l SAPNTAB.log -nojournal' exited with return code 2.
For mode details see 'SAPNTAB.log' file.
Standard error output:
¢u2014u2014u2122
What seems missing to check? We are on applying the mssing PTF but still stuck with PTF not fuond from media msg . Thanks for reading the details.
Regards,
-asp-

Hi -asp-,
From your description it is not clear to me whether you checked against infoapar.455 or not. If you missed this, follow the descriptions of note 144149.
Regarding the SQL -901 you need to look up the joblog of the failing process and check the messages right before the SQL -901 for the real reason.
HTH,
Thomas

Getting descriptor version does not match runtime version error

Thanks,
I am Using Adope Air SDK2.0 and Runtime Air 1.0.7,
i have created one HelloWorld application using Adope sample
code.
When i am trying to run this using commands :
i have used : adl HelloWorld.html
i am getting this error:
invalid application descriptor: descriptor version does not
match runtime version
Plz help me out.. :-)

The issue I had in Flashbuilder4 has been solved.
The easiest but possibly not the neatest was too copy the AIR 2 Beta SBK folders and files, then paste the over the flex4.0 sdk file structure. Achieves the same thing and I assume that you have copies of the SDK else where, if you need to roll back.
The other thing is to make sure the -app.xml that flex creates has the correct 2.0beta description.
Cheers
Elliot

Does not match component version

Hi,
We have four system landscape. We have already upgrade our DEV and ITT to EHP5.We still have to upgrade our UAT and prod to EHP5. When I see the transport queue on ITT system.I see all the transport that was imported on ITT before the upgrade is showing as "Does not match component version".
I can understand that the version before the upgrade was different so it should show that message.
I just wanted to check if this is normal or I need to make changes to TMS?
Regards!
Ravi

Hi,
You can do as follows:
Switch it off with parameter : SP_TRANS_SYNC = OFF
Procedure:
Call transaction STMS
Goto 'Systems Overview'
Double click <SID> you wish to add the parameter to
Goto 'Transport Tool' tab
Goto 'change mode'
Add SP_TRANS_SYNC to parameter column and OFF to value column
Save, activate and distribute
With Version SAP_BASIS 702 a new feature was added to the TMS system,
tp is now checking the component version of the transport which was
released and the component version of the system where the transport is
going to be imported. If there is a difference, this difference is
highlighted in the import queue (transaction stms_import) and if you try
to import the transport, the import will stop with a warning message
about the difference in the SAPCOMPONENT versions.
If you wish to by-pass with warning then you can choose 'Ignore invalid
Component version'.
Regards,
Aidan

Firefox crashes whenever i want to install any addon or download any file. Some times i am receiving error while downloading any file like "could not be saved, because you cannot change the contents of that folder"

I am the user of latest firefox 3.6.6 browser. I am getting problems of frequent crashes whenever i tries to install any addon. The crashes also occures whenever i want to download any file.
I am also receiving errors while downloading any file like:
"C:\Users\****\AppData\Local\Temp\******.001.part could not be saved, because you cannot change the contents of that folder.
Change the folder properties and try again, or try saving in a different location. I already changed it many many times but still the same problem."
Adobe flash palyer is also giving problems of not responding. I am using updated version of it already. Java is also updated.
I already uninstalled firefox compeletly and re installed it many many times but still the same problem. I also scanned my computer with avira and malware bytes' Anti malware and got no dection. Please ractify this problem ASAP lest my profession will suffer.
== Crash ID(s) ==
b7f518f2-8d86-41ca-8bab-aee632100709; 1d790e10-d8eb-4904-98c9-94bc62100708; f042d319-b9f8-42ed-a8cb-57c7d2100708

Please help.
It is getting worse
Adobe flash player is crashing. I already uninstalled and re installed the latest ver. Also it is hanging randomly.
Please help.

CRMv1.2 Enter this License key is invalid or does not match the organization name?

Hi All,
Thanks for your support in advance.
This is Ashok. We purchased CRM v1.2 from the third party. They have provided us the CRM CD's(5) with product key. The problem is when im trying to install CRM server in windows 2003 server its asking for organizations name and License Key. So I have entered
my company name as the organization name and entered the product key as a License Key. After click on the add button its giving an error i.e., "Enter this License key is invalid or it does not match the organization name. Verify your license key and organization
name".
Kindly suggest me the best solution to resolve this issue.
Waiting for your valuable suggestions.
Thanks,
Ashok M.

Hi Ashok,
We have a specific forum for discussing CRM:
https://social.microsoft.com/Forums/en-US/home?forum=crm
However from the description it is a license related question. In this situation it is more recommended to contact the support directly:
Here is the support page for Microsoft Dynamics:
http://www.microsoft.com/dynamics/en/asia/contact-support.aspx
Please remember to mark the replies as answers if they help and un-mark them if they provide no help. If you have feedback for TechNet Support, contact [email protected]

Since I did the Firefox reset, I try to open my email and it says, Your browser does not accept cookies. I have checked the cookies setting 100 times!

Since I did the Firefox reset, I try to open my email and it says, Your browser does not accept cookies. I have checked and done your suggested setting 100 times!

Note that a reset tries to migrate cookies to the new profile, so if you had previously as problem with cookies then the problem might have been carried over.
If clearing cookies doesn't work then it is possible that the cookies.sqlite file that stores the cookies is corrupted.
Rename (or delete) cookies.sqlite (cookies.sqlite.old) and delete other present cookie files like cookies.sqlite-journal in the Firefox profile folder in case the file cookies.sqlite got corrupted.
*http://kb.mozillazine.org/Cookies
*https://support.mozilla.org/kb/Deleting+cookies

CodeError: Identity does not match. How do I change the indentity?

I had a developer make the program for me. I open the project in xCode and try to Build It with either Release or Distribution and it comes up with error:
"CodeSign error: Code signing identity "iPhone Developer: Joe Smith" does
not match any code-signing certificate in your keychain. Once added to
the keychain, touch a file or clean the project to continue"
How do I change the CodeSign to know it is me? Joe Smith is the guy who developed the software, but I need to publish it.
Also, for submitting to "App Store" do I Build it via "Release" or "Distribution"??

Is it the password to the laptop itself or the iTunes Store?
Cheers,
Adam

The version of this vi downloaded on the target does not match the version you have in the project

Similar Messages

Maybe you are looking for