The zpool configured in HA Suncluster is corrupted after switching RG

Hi,
i have some zpool with our RG configured in HA Solaris 10 SunCluster 3.2. When i moving the resource group from node 1 to node 2 the zpool is corrupted e must be reconfigured.
I see this error in the messages files:
May 12 16:09:10 voelsung Cluster.RGM.fed: [ID 922870 daemon.error] tag
vb1.vb1-storage.10: unable to kill process with SIGKILL
May 12 16:09:10 voelsung Cluster.RGM.rgmd: [ID 904914 daemon.error] fatal:
Aborting this node because method <hastorageplus_prenet_start> on resource
<vb1-storage> for node <voelsung> is unkillableI find many forums with this technical information about configuration:
# cldevice list -v
DID Device Full Device Path
d3 phys-schost-1:/dev/rdsk/c1t8d0
d3 phys-schost-2:/dev/rdsk/c1t8d0
The zpool can be configured with Solaris device identifier:
# zpool create vb1 c1t8d0s2
The zpool can be configured with DID or logical device identifier:
# zpool create vb1 /dev/did/dsk/d3s2
I see to many problems about corrupting filesystem/pool, during switching the RG, using Solaris device identifier and the correct configuration is using DID or logical device identifier.
Do you is true this best practice in the forums or conference?
Regards
Mario

A change to the zpool_import() management of the zpool.cache file, as delivered by Solaris 10 kernel patches 137137-09 (for SPARC) or 137138-09 (for x86), might cause systems that have their shared ZFS (zfs(1M)) storage pools under the control of HAStoragePlus to be simultaneously imported on multiple cluster nodes. Importing a ZFS storage pool on multiple cluster nodes will result in pool corruption, which might cause data integrity issues or cause a cluster node to panic.
To avoid this problem, install Solaris 10 patch 139579-02 (for SPARC) or 139580-02 (for x86) immediately after you install 137137-09 or 137138-09 but before you reboot the cluster nodes.
Alternatively, only on the Solaris 10 5/08 OS, remove the affected patch before any ZFS pools are simultaneously imported to multiple cluster nodes. You cannot remove patch 137137-09 or 137138-09 from the Solaris 10 10/08 OS, because these patches are preinstalled on that release.

Similar Messages

OS X partition becomes corrupt after switching from Bootcamp

So I've had to reinstall os x 10.9.1 no less than three times this week and multiple times before in the past after switching between os x and windows 8.1. This usually happens after I've been using windows for a prolonged period then switch back to os x but it happened today after reinstalling os x from a time machine backup just yesterday. I'll switch between the two and os x becomes corrupt and begins the loading bar sequence after selecting the os x partition via the refit boot manager. I tried repairing the partition using disk utility from the repair partition and an external installation of os x 10.9.1 but every time the disk becomes corrupt and needs to be wiped and reinstalled or install a time machine backup. I've lost count of how many times I've had to do this and to make things even worse both of my external disks have become corrupt after being disconnected for two days while I sort this mess out. Does anyone else have similar issues or can locate an issue somewhere?

Yeah I reinstalled osx 10.9.1 and installed all my apps, put everything back then used bootcamp to create a partition for windows then used wineclone to install my windows 8.1 backup. I jumped from windows > osx > windows > osx inside an hour to move around a few things and I forgot verify bootcamp after I installed the backup and that last time I booted to osx it was corrupted. I used disk utility from my external installation and the recovery partition and both times they need repaired which only came up with the backup and wipe notification window. There have been two occasions where I was able to fix the osx partition from my external osx installation and continue using osx quite perfectly but usually the partition becomes un-mountable after it fails to repair. Usually when this has happened the twenty something times before it's after a prolonged period of a few weeks using windows.
I'm using refit boot manager and paragon NTFS 11 which may be the only software I've installed that could be corrupting the boot.
SMART status is verified

Command Button colors corrupt after switching back and forth from design view.

I would say my experience level with Access is "getting there."
I therefore don't thing I'm making a newbish mistake.
Has anyone else noticed this? As it's bugging me quite badly.
1. A command button has had it's color formatted (pressed, hover, etc. nothing fancy)
2. It works fine.
3. In my navigation form, if I switch to design view, then select a given sub-form... like "customers" - and switch back out of design view, to form view - then without fail, all customized command buttons within that sub forms' color will 'corrupt'
ie, change.
4. Closing and reopening the navigation form (ie, my main menu) restores it, but the same thing will happen should I go back to design view for the sub form.
5. Finally - this behaviour does not happen when switching back and forth between views on the original form that isn't a sub form in the navigation form. (Ie,. the main 'customers' form).
Can any clever folk give me a solution? :(
Thanks,
Eric Rowlands
EDIT - My apologies, I am using Access 2013 for a desktop database.

1) We will need to understand whether the issue is seen on any sample database.
2) IS this seen only on your system, we would need to check on other system also
3) If the issue is seen in all system & issue is not seen in the sample database then this could be database specific issue
4) As per my understanding the issue is consistent, we would need to find what is the VBA code or which code is used while designing this form.
5) We would need to see if the issue is seen only on that particular navigation form?
6) Is the button gets corrupt I mean to say non-usable once it get discolored ?
7) What is your end goal just in case if you are able to work on your database i.e. when working on the navigation form without going in design view is issue still seen there ?
8) Since when are you experiencing this issue ?
9) If possible please provide me the environment details of your system & Access application, whether the issue is seen only in access 2010 can we check in access 2007 or in access 2013.
I would really appreciate if you can answers the above questions this will really help us to isolate the issue further
in terms of technical troubleshooting after answering the above question I might come up with another question so that we can do extensive isolating the issue so the if required we can involve the developer also.

I up graded to Lion OsX and when I configured my POP account, it says is null and with the same configuration in my Macbook I have no problem at all, what can I do?

I upgraded my operating system to Lion osx 10.7 and after I ibnstalles it I coul not receive or send emails from my POP account, yes from my IMAP accounts,Itried to configure it again with the same configuration I have in my Macbook with Leopard system and it say its null, what can I do?
Carlos38

That issue can be caused by corrupted cookies.
Clear the cache and the cookies from sites that cause problems.
"Clear the Cache":
* Firefox > Preferences > Advanced > Network > Offline Storage (Cache): "Clear Now"
"Remove Cookies" from sites causing problems:
* Firefox > Preferences > Privacy > Cookies: "Show Cookies"
If clearing the cookies doesn't help then it is possible that the file cookies.sqlite that stores the cookies is corrupted.
Rename (or delete) cookies.sqlite (cookies.sqlite.old) and delete cookies.sqlite-journal and cookies.txt, if they exist, in the Firefox Profile Folder in case the file cookies.sqlite got corrupted.
*http://kb.mozillazine.org/Profile_folder_-_Firefox

BCDEDIT.EXE /CREATESTORE causes error the boot configuration store could not be opened

I'm upgrading XP to Windows 7 with dual boot using an image and successfully installed on 6 other computers, the last two are failing when I issue the command:
bcdedit.exe /createstore
The boot configuration data store could not be opened.
The requested system device cannot be found.
I'm using a known good WINPE 4.0 (Windows 8) x64 USB boot environment, so most solutions that state to run elevated as an administrator do not apply.
C: is NTFS active partition, chkdsk doesn't find any errors on C:
I've updated the bootsector with the command
bootsect /nt60 c: /force /mbr
this of course disables booting into XP, but I can reboot and re-enable XP via
bootsect /nt52 c: /force /mbr
If I try a modified command
bcdedit.exe /createstore c:\BOOT\BCD
this also fails, and I've verified that the hidden system C:\BOOT folder does not exist before issuing the command
If I pre-create c:\BOOT (w/o hidden or system attributes) the command
bcdedit.exe /createstore c:\BOOT\BCD
does run successfully, but the following commands to add the Windows 7 boot entries and legacy NTLDR for XP dual boot still fail!
bcdboot.exe d:\windows /s c: /v
bcdedit.exe /create {ntldr} /d "Windows XP SP3"
bcdedit.exe /set {ntldr} device partition=C:
bcdedit.exe /set {ntldr} path \ntldr
bcdedit.exe /displayorder {ntldr} /addfirst
bcdedit.exe /default {ntldr}
bcdedit.exe /timeout 5
The two failing computers are older Dell OptiPlex 960 models, so I'm using traditional BIOS boot, EFI is not supported on these models. Hard drives are regular SATA (1 per computer), no other mass storage devices present besides DVD (empty), and hard
drives are not GPT formatted. Drives are old enough that they are regular 512 sector devices (no 512 emulation or 4K issues).

Thanks for your response Niki Han, the current status is the computers are booting correctly into the original XP SP3, since I've started them with my WINPE
4.0 x64 USB flash drive and issued the command to restore the original NTLDR boot process "bootsect /nt52 c: /force /mbr".
I also verified that there are no hidden partitions, and that there is only one active partition, C: which is a standard NTFS volume:
Partition 1
Type : 07
Hidden: No
Active: Yes
I've also verified that the BIOS is the same and the hard drive mode set in the BIOS is the autodetect RAID in both the working and non-working systems. I'll review the article you provided at
http://technet.microsoft.com/en-us/library/ee829686(v=ws.10).aspx#BKMK_Step4
which may allow me to get these two systems dual booting. I do know that I'll need to delete the corrupted hidden system c:\Boot folder to avoid any issues.
I do want to figure out why the command
bcdedit.exe /createstore
is outputting this error on just these two systems:
The boot configuration data store could not be opened.
The requested system device cannot be found.
What exactly does bcdedit.exe do when given the /createstore command, does it create a new empty store from the exe itself, or does it copy a store from the running system? I think the key to figure this out is understanding what the error "The
requested system device cannot be found." is trying to tell us.

I am attempting to update students' iPads using the Apple Configurator software. However, information for 3rd party apps, like Notability and Explain Everything, is being lost.

I am attempting to update students' iPads using the Apple Configurator software. However, information for 3rd party apps, like Notability and Explain Everything, is being lost.

Mike,
If by "still nothing" you mean they are not showing up in the AU manager after reinstalling them....
Im guessing the AU Cache itself is now corrupted so.....
Quit LPX
Open Finder
Press the option key and click "Go" in Finder's menu and select "Library". (This is the User Library and not the System Library and is normally hidden which is why you have to hold down the option key when clicking on Go.... to reveal it in the drop down menu that will appear)
Go to "Caches" dir and remove "AudioUnitCache" dir.
Now Restart your Mac.....
and then Launch LPX and let it rescan your plugins and see if that fixes things....
Fingers crossed...
Nigel

Please ensure that the applicationhost.config file is correct and recommit the last configuration changes made

I am receiving event ID 5189 on Server 2008 R2, IIS 7.5. I experience this error across a number of servers, each of which is running only the default web site, but have 600+ applications running on the default web site. Each application
has its own application pool. My point is, the applicationhost.config is rather large.
I have seen a number of posts on this error message, but my issue itself seems to differ somewhat. I am aware of a similar post: http://social.technet.microsoft.com/Forums/en-US/3128ee93-1319-4cc2-9257-003512caf476/event-id-5189-microsoftwindowswas?forum=exchangesvrgeneral
which points to KB http://technet.microsoft.com/en-us/library/cc734988%28v=ws.10%29.aspx
However, in my case, it doesn't seem that the extreme measures for this resolution are required. The error usually indicates a corrupted applicationhost.config that must be manually fixed, or otherwise the WAS service needs to be restarted, or the
server itself, etc.
In my case, the issue can usually be fixed by an application pool recycle, or at worst a stop/start. I have an application which is sensitive to recycles, and so we do not have periodic recycle events configured for this application, which is the bulk
of the applications on the servers. It seems to me that this issue is usually caused by the application being in use when there is an applicationhost.config change.
For instance, we have one application that we deploy using msdeploy. We found that when we ran an installation for this application via msdeploy, we were receiving this event, and we would subsequently get 500 errors in the application (sometimes the
application pool corresponds to that which is identified in the event log, sometimes it doesn't).    It seems like applications that were being hit at the time the applicationhost.config was modified by msdeploy were affected. In an attempt
to correct this, we moved from msdeploy to a batch file containing appcmd commands. This also did not resolve the issue.
I have another application which is installed using PowerShell commandlets. We started to notice that this script also caused the issue to occur on occasion. As I continued to identify different processes that resulted in the same issue, I came
to the conclusion that this is likely due to any change in the applicationhost.config. I assume the issue is that the applicationhost.config is modified during a read operation to the file by the application pool, or WAS service, and that the recycle
event, which corrects the issue, forces a re-read of the applicationhost.config, resolving the bad-read issue.
Has anyone else experienced this, or do you have any recommendations? My current work-around is to not install any applications during peak hours, and performing an IISRESET after installs are completed, to ensure application stability.
Message              : The Windows Process Activation Service failed to generate an application pool config file for application pool 'myAppPool'. The error type is '7'. To resolve this issue,
please ensure that the applicationhost.config file is correct and recommit the last configuration changes made. The data field contains the error number.
Id                   : 5189
Version              : 0
Qualifiers           : 49152
Level                : 2
Task                 : 0
Opcode               : 0
Keywords             : 36028797018963968
RecordId             : 324108
ProviderName         : Microsoft-Windows-WAS
ProviderId           : 524b5d04-133c-4a62-8362-64e8edb9ce40
LogName              : System
ProcessId            : 0
ThreadId             : 0
MachineName          : MyComputer
TimeCreated          : 3/3/2014 9:03:24 PM
ContainerLog         : system
MatchedQueryIds      : {}
Bookmark             : System.Diagnostics.Eventing.Reader.EventBookmark
LevelDisplayName     : Error
KeywordsDisplayNames : {Classic}
Properties           : {System.Diagnostics.Eventing.Reader.EventProperty, System.Diagnostics.Eventing.Reader.EventProperty, System.Diagnostics.Eventing.Reader.EventProperty}

As an update to this issue, after doing some research, it appears the behavior is related to a new feature in IIS7 called Application Pool Isolation (http://technet.microsoft.com/en-us/library/dd163536.aspx).
This new feature prevents cross-application spillage by isolating the configuration for each application pool in IIS. So in reality, an application pool never actually reads the applicationhost.config - that is just a master file, and each time it
is update, it triggers a change to the individual application pool configuration files, located in C:\inetpub\temp\apppools.
We did try setting Advanced Settings > Disable Recycling for Configuration Change to true, but after an IIS reset we were still able to reproduce the issue - worse actually, because in our test program, which continually hits the web
service, and also continually makes apphost.config changes, when the two events collide, the 500.19 issue precipitates; but after an additional change to the apphost.config, it seems that the additional changes will actually correct the issue (seemingly forcing
another recycle, which is also how we resolve the issue manually); after making this setting adjustment, once the 500.19 issue precipitates, additional changes to the apphost.config does not correct the problem, only a manual recycle corrects it. This
is the recycling.disallowRotationOnConfigChange property of the app pool. We also set the setting for recycling.disallowOverlappingRotation to True as well, with the same result.
We ARE able to prevent this issue by setting the C:\inetpub\temp\apppools\myapppool\myapppool.config to read-only, but for obvious reasons, this is not a desired work-around.
It seems like what is happening is that any change to the ApplicationHost.config is resulting in each of the C:\inetpub\temp\apppools temp application pool config files being updated as well, in addition to triggering an application pool recycle. It
seems to me the desired behavior would be that these files are only updated if the applicationhost.config changes are specific to that application pool - but that doesn't seem to be the behavior.
After turning on failed request tracing, I was able to narrow the error down more:
ModuleName
AnonymousAuthenticationModule
Notification
2
HttpStatus
500
HttpReason
Internal Server Error
HttpSubStatus
19
ErrorCode
2147942413
ConfigExceptionInfo
\\?\C:\inetpub\application\application\web.config ( 9) :Failed to decrypt attribute 'password'
Notification
AUTHENTICATE_REQUEST
ErrorCode
The data is invalid. (0x8007000d)
This seems to be pretty static. Trying to look into possible causes of this issue.

T60 - Error while attempting to read the boot configuration data

Hello,
My wife just got an IBM-certified "pre-owned" T60 (type 2007 66U) running XP a few days ago. I updated all the drivers & patches and handed it over to her in good working order.
This morning when she turned it on, she encountered a message from the Windows Boot Manager:
Windows failed to start. A recent hardware or software change might be the cause. To fix the problem:
1) Insert your Windows installation disc
2) Language settings
3) Repair your computer
If you do not have this disc....
File: \Boot\BCD
Status: 0xc000000f
Info: An error occurred while attempting to read the boot configuration data
It almost goes without saying that we do not having our Windows installation disc as it was pre-installed by Lenovo. I've tried using F11 (after enabling it per other threads on this site) to access the recovery partition but it only takes me directly to the Windows Boot Manager error screen.
How do I go about repairing this BCD/Windows installation so we can continue our life?
Thanks...

You said that the computer is running Windows XP, but unless i'm wrong BCD (Boot Configuration Data) is a new feature starting with Windows Vista and also used by Windows 7. Windows XP use NTLDR (NT Loader) so if BCD is corrupted it sounds to me like someone tried to install Vista og Win7 on the computer or there might have been some leftovers from the previous owner. I don't think you have any other option but to use a Windows CD/DVD to fix this problem since you won't be able to boot from this computer. There might be some 3part utilities available that should be able to fix this, but i wouldn't know what that might be. My recommendation would be to get a Windows CD/DVD.
-gan

The error "configuration system failed to initialize" occurred

Hi
When I converted and built the solution file that was developed by Visual Studio .net 2003 using Visual Studio 2005, the application program was abnormal-ended at the following step:
m_TCPChannel = New System.Runtime.Remoting.Channels.Tcp.TcpChannel(tcp_properties, Nothing, Nothing)
The error message was "configration system failed to initialize". The Exception.ToString said that the root <configuration> tag was not included in the configuration file. Therefore, I changed <configopt> tag to <configuration>
tag in the app.config file of the target project, and then executed again. Next time, the application program was abnormal-ended by the unrecognized section <xs:schema>. Therefore, I changed the app.config file to the simple one (only <configuration>
and </configuration> tags), and then executed again. The error didn't occur. I guess that it's caused by configuration settings. Please advise.
app.config file:
<?xml version="1.0" standalone="yes"?>
<configopt>
<xs:schema id="configopt" xmlns="" xmlns:xs="URLリンク" xmlns:msdata="urn:schemas-microsoft-com:xml-msdata">
<xs:element name="configopt" msdata:IsDataSet="true" msdata:Locale="en-AU">
<xs:complexType>
<xs:choice maxOccurs="unbounded">
<xs:element name="Environment">
<xs:complexType>
<xs:sequence>
<xs:element name="Name" type="xs:string" minOccurs="0" />
<xs:element name="System" type="xs:string" minOccurs="0" />
<xs:element name="DataLibrary" type="xs:string" minOccurs="0" />
<xs:element name="Default" type="xs:boolean" minOccurs="0" />
<xs:element name="UserId" type="xs:string" minOccurs="0" />
</xs:sequence>
</xs:complexType>
</xs:element>
</xs:choice>
</xs:complexType>
</xs:element>
</xs:schema>
<Environment>
<Name>Test</Name>
<System>XXXX.COM</System>
<DataLibrary>XXXTEST</DataLibrary>
<Default>false</Default>
<UserId></UserId>
</Environment>
<Environment>
<Name>Production</Name>
<System>XXXXX.COM</System>
<DataLibrary>XXXPROD</DataLibrary>
<Default>true</Default>
<UserId />
</Environment>
</configopt>

Hi,
Thank you for your post.
I am afraid that the issue is out of support range of VS General Question forum which mainly discusses the usage of Visual Studio IDE such as
WPF & SL designer, Visual Studio Guidance Automation Toolkit, Developer Documentation and Help System
and Visual Studio Editor.
Since your issue occurred on the converted project from VS .net 2003 to VS2005, and VS2005 is out of
our mainstream support , I suggest that you should consult on some development forums to check whether they will to provide some suggestions or
submit a support ticket to below site,
https://support.microsoft.com/oas/default.aspx?Gprid=1117&st=1&wfxredirect=1&sd=gn&wfxredirect=1
Thank you for your understanding.
Best regards,
We are trying to better understand customer views on social support experience, so your participation in this interview project would be greatly appreciated if you have time. Thanks for helping make community forums a great place.
Click
HERE to participate the survey.

The boot configuration data for your Pc is missing or contains errors: error code 0x000014c

Hello,
See if any body may help here... I get this blue screen:
RECOVERY
Your PC needs to be repaired:
The Boot Configuration Data for your PC is missing or contains errors.
file:\\EFI\Microsoft\Boot\BCD
Error code: 0xc000014c
You'll need to use the recovery tools on your installation media. If you don't have any installation media (like a a disc or USB device), contact your system administrator or PC manufacturer.
Press Esc for UEFI Firmware Settings
First I was able to get into the option 11 and run the whole factory reset, i was so happy because I tought it will be easy.. but then after I did the factory reset.. I keep getting this blue screen. if I press ESC I get into this next screen:
F1 System Information
F2 System Diagnostics
F9 Boot Device Options
F10 BIOS Setup
F11 System Recovery
ENTER - Continue Startup.
this is what happen when I click any of this options:
F1 I get into the System Information with no problems, then I click <ESC> to continue and get back to the last screen... then I press F2 and super, I am able to run Memory Test and Hard Drive Check 100% with no problems in any of those, after I am done with my teste I press exit and I am back to the F1,F2, ETC menu... now I want to try F9, F10 or F11. bummer.. in this 3 options I get back to the blue screen described at the beggining of this post. (I already connect a USB with an boot loader, which works perfectly)
so I can't do anything, nothing at all!! crazzines.
So what I did to check why I can't get into the BIOS or at least to boot from my USB... I removed the botton cover of my laptop and removed the hard drive and that's how then I was or I am able to Log into the BIOS, - I did the changes to boot first from the USB and then from the HD and this is how I was able to boot from the USB - BUT If I connect back the Hard drive, I am not able to get into the BIOS or boot from the USB - so basically I am stuck in this blue screen and I can't boot from a USB if I have the HD connected.. I can't use any option.. no BIOS, nothing.. only if again, i disconnect the HD.
This is an:
HP ENVY TS Sleekbook 4
PRODUCT NUMBER D1A99UA#ABA
SYSTEM BOARD ID: 1894
Bios F.25
**** I though that by updating the BIOS I may be able to get help, nothing. What I did is, I removed the HD and then and boot from the USB and with a DOS command propmt I excecuted the Bios Update from F.21 to f.25... but again, when I installed the hard drive back, BUMMER, nothing I can't do nothing but this silly blue screen.
Any idea of what should I do?
Thanks in advance.
This question was solved.
View Solution.

If you can't access BIOS with the hard disk connected, you certainly won't be able to boot to the usb recovery flashdrive. That is indicative of a failed hard disk.
Install a new hard disk and then boot to the recovery flashdrive.
****Please click on Accept As Solution if a suggestion solves your problem. It helps others facing the same problem to find a solution easily****
2015 Microsoft MVP - Windows Experience Consumer

Unable to load the pof configuration

Hi all,
Im trying with pof serialization but unable to load the pof configuration and im getting the following error:
2013-06-12 14:41:49,582 [catalina-exec-1] ERROR com.distcachedemo.KnCacheDemoServlet - doPost(HttpServletRequest, HttpServletResponse)::
(Wrapped) java.io.NotSerializableException: com.distcachedemo.dto.KnMasterListResponse
 at com.tangosol.util.ExternalizableHelper.toBinary(ExternalizableHelper.java:215)
 at com.tangosol.coherence.component.util.daemon.queueProcessor.service.grid.partitionedService.PartitionedCache$ConverterValueToBinary.convert(PartitionedCache.CDB:3)
 at com.tangosol.util.ConverterCollections$ConverterMap.put(ConverterCollections.java:1674)
 at com.tangosol.coherence.component.util.daemon.queueProcessor.service.grid.partitionedService.PartitionedCache$ViewMap.put(PartitionedCache.CDB:1)
 at com.tangosol.coherence.component.util.SafeNamedCache.put(SafeNamedCache.CDB:1)
 at com.distcachedemo.KnCorpContactInfoControllerDemo.getMasterList(KnCorpContactInfoControllerDemo.java:183)
 at com.distcachedemo.KnCacheDemoServlet.doPost(KnCacheDemoServlet.java:60)
Please let me know what is that i need to correct in the below:
NOTE: I have also tried Proxy Scheme with serializer and it too did not work
 From the coherence logs i havent found the log of POF configuration being loaded.
Configuration used:
============
cache-config.xml::
<?xml version="1.0"?>
<cache-config xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance"
 xmlns="http://xmlns.oracle.com/coherence/coherence-cache-config"
 xsi:schemaLocation="http://xmlns.oracle.com/coherence/coherence-cache-config coherence-cache-config.xsd">
 <caching-scheme-mapping>
 <cache-mapping>
 <cache-name>nspoc*</cache-name>
 <scheme-name>distributed-ns</scheme-name>
 </cache-mapping>
 <cache-mapping>
 <cache-name>poc*</cache-name>
 <scheme-name>distributed</scheme-name>
 </cache-mapping>
 </caching-scheme-mapping>
<caching-schemes>
 <distributed-scheme>
 <scheme-name>distributed-ns</scheme-name>
 <service-name>DistributedCache-ns</service-name>
 <thread-count>4</thread-count>
 <request-timeout>60s</request-timeout>
 <backing-map-scheme>
 <external-scheme>
 <nio-memory-manager>
 <initial-size>1MB</initial-size>
 <maximum-size>100MB</maximum-size>
 </nio-memory-manager>
 <high-units>100</high-units>
 <unit-calculator>BINARY</unit-calculator>
 <unit-factor>1048576</unit-factor>
 </external-scheme>
 </backing-map-scheme>
 <autostart>true</autostart>
 </distributed-scheme>
 <distributed-scheme>
 <scheme-name>distributed</scheme-name>
 <service-name>DistributedCache</service-name>
 <thread-count>4</thread-count>
 <request-timeout>60s</request-timeout>
 <backing-map-scheme>
 <read-write-backing-map-scheme>
 <internal-cache-scheme>
 <external-scheme>
 <nio-memory-manager>
 <initial-size>1MB</initial-size>
 <maximum-size>100MB</maximum-size>
 </nio-memory-manager>
 <high-units>100</high-units>
 <unit-calculator>BINARY</unit-calculator>
 <unit-factor>1048576</unit-factor>
 </external-scheme>
 </internal-cache-scheme>
 <cachestore-scheme>
 <class-scheme>
 <class-factory-name>com.distcachedemo.KnPocCacheStoreFactory</class-factory-name>
 <method-name>loadCacheStore</method-name>
 <init-params>
 <init-param>
 <param-type>java.lang.String</param-type>
 <param-value>{cache-name}</param-value>
 </init-param>
 </init-params>
 </class-scheme>
 </cachestore-scheme>
 </read-write-backing-map-scheme>
 </backing-map-scheme>
 <autostart>true</autostart>
 </distributed-scheme>
 <local-scheme>
 <scheme-name>LocalSizeLimited</scheme-name>
 <eviction-policy>LRU</eviction-policy>
 <high-units>5000</high-units>
 <expiry-delay>1h</expiry-delay>
 </local-scheme>
 </caching-schemes>
</cache-config>
=================
tangosol-coherence-override.xml:
<?xml version='1.0'?>
<coherence xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance"
 xmlns="http://xmlns.oracle.com/coherence/coherence-operational-config"
 xsi:schemaLocation="http://xmlns.oracle.com/coherence/coherence-operational-config coherence-operational-config.xsd">
 <cluster-config>
 <member-identity>
 <cluster-name system-property="tangosol.coherence.cluster">kn_test</cluster-name>
 </member-identity>
 <unicast-listener>
 <well-known-addresses>
 <socket-address id="719">
 <address>192.168.7.19</address>
 <port>8088</port>
 </socket-address>
 <socket-address id="3246">
 <address>192.168.3.246</address>
 <port>8088</port>
 </socket-address>
 <socket-address id="77">
 <address>192.168.7.7</address>
 <port>8088</port>
 </socket-address>
 </well-known-addresses>
 <address system-property="tangosol.coherence.localhost">192.168.7.7</address>
 <port system-property="tangosol.coherence.localport">8088</port>
 <port-auto-adjust system-property="tangosol.coherence.localport.adjust">true</port-auto-adjust>
 </unicast-listener>
<serializers>
 <serializer id="java">
 <class-name>com.tangosol.io.DefaultSerializer</class-name>
 </serializer>
 <serializer id="pof">
 <class-name>com.tangosol.io.pof.ConfigurablePofContext</class-name>
 <init-params>
 <init-param>
 <param-type>String</param-type>
 <param-value>pof-config.xml</param-value>
 </init-param>
 </init-params>
 </serializer>
 </serializers>
 </cluster-config>
 <configurable-cache-factory-config>
 <init-params>
 <init-param>
 <param-type>java.lang.String</param-type>
 <param-value system-property="tangosol.coherence.cacheconfig">cache-config.xml</param-value>
 </init-param>
 </init-params>
 </configurable-cache-factory-config>
</coherence>
======================
pof-config.xml:
<?xml version='1.0'?>
<pof-config xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance"
 xmlns="http://xmlns.oracle.com/coherence/coherence-pof-config"
 xsi:schemaLocation="http://xmlns.oracle.com/coherence/coherence-pof-config
 coherence-pof-config.xsd">
 <user-type-list>
 <include>coherence-pof-config.xml</include>
 <user-type>
 <type-id>1001</type-id>
 <class-name>com.distcachedemo.dto.KnMasterListResponse</class-name>
 </user-type>
 </user-type-list>
</pof-config>
============
Java Code:
package com.distcachedemo.dto;
import com.tangosol.io.pof.PofReader;
import com.tangosol.io.pof.PofWriter;
import com.tangosol.io.pof.PortableObject;
import java.io.IOException;
import java.io.Serializable;
import java.util.ArrayList;
import java.util.HashMap;
import java.util.Map;
public class KnMasterListResponse implements PortableObject {
private static final long serialVersionUID = -9114918011531875153L;
private KnHierarchyListDTO hierarchyListDTO;
private Map subsMap;
public KnHierarchyListDTO getHierarchyListDTO() {
return hierarchyListDTO;
public void setHierarchyListDTO(KnHierarchyListDTO hierarchyListDTO) {
this.hierarchyListDTO = hierarchyListDTO;
public Map getSubsMap() {
return subsMap;
public void setSubsMap(Map subsMap) {
this.subsMap = subsMap;
public String toString() {
StringBuilder strBuffer = new StringBuilder(100);
if (hierarchyListDTO.getHierachyDTOs() != null) {
strBuffer.append(" hierarchyListDTO - ").append(hierarchyListDTO.getHierachyDTOs().size());
if (subsMap != null) {
strBuffer.append(" subsMap - ").append(subsMap.size());
return strBuffer.toString();
@Override
public void readExternal(PofReader pofReader) throws IOException {
subsMap = pofReader.readMap(0, new HashMap<>());
hierarchyListDTO = (KnHierarchyListDTO) pofReader.readObject(1);
@Override
public void writeExternal(PofWriter pofWriter) throws IOException {
pofWriter.writeMap(0, subsMap);
pofWriter.writeObject(1, hierarchyListDTO);
Thanks,
Ravi Shanker

Hi Ravi,
it is generally recommended that all new classes support POF in this or that way. This or that means either implementing PortableObject or to provide a PofSerializer implementation to be able to optimally serialize their state. Obviously it is not always possible but you should try to achieve that.
If it is not possible, then you can still convert them to byte[] or String by some other means. If that other means is Java serialization, then Coherence provides a different PofContext implementation (SafeConfigurablePofContext) which you can use instead of ConfigurablePofContext and which is able to fall back to Java serialization for Serializable classes (and also for types not registered in POF configuration but which implement PortableObject). However it is recommended that SafeConfigurablePofContext is not used in production, typically because Java serialization is generally inferior to POF serialization when looking at performance and serialized size, and SafeConfigurablePofContext does not force you to do the right thing, and finally because Java serialization is not platform-independent whereas POF is.
Best regards,
Rob

What is the reason that the integrated camera does not exist in the hardware configuration?

When I start Face Time, my integrated camera doesn't work.
I check my hardware configuration, but, the camera doesn't exist.

Welcome to Apple Support Communities
Does it happen with other applications that use the camera, like Photo Booth? If so, I recommend you to reset the PRAM > http://support.apple.com/kb/HT1379 Then, reset the SMC > http://support.apple.com/kb/HT3964
After resetting the SMC, start the iMac and see if you can use your camera. If not, hold Command and R keys while your computer is starting and reinstall OS X through OS X Recovery > http://support.apple.com/kb/HT4718
If it doesn't work, it's a hardware issue, so make a backup of your data and take the iMac to an Apple Store or reseller

My Cox Cable/Telephone splits to a telephone modem and a broadband modem. The BB connects via ethernet to a Cisco Linksys E2500 wi-fi (whatever). Can I plug my usb printer into the E2500, configure, and then print from my iPad?

I have just purchased an iPad 2. I have wi-fi for roku and have connected the iPad to it. I want to print to my usb printer. My connection is: Cox Cable spit to telephone and broadband. The broad band feed goes to a Cox modem and feeds the wi-fi. The Cisco Linksys E2500, wi-fi's the Roku and iPad. Can I USB from the wi-fi to the printer, configure (however), and then print from my iPad?
If not, how?
All comments will be appreciated.
Alan G. Watkins

the ipad cannot airprint to a non airprint printer.... i think that the only solution is to install helper software on a computer that has an attached printer and share it through the computer only...computer would have to be always left on
try this....http://www.collobos.com

How can I list all the domains configured for Weblogic Servers?

How can I list all the domains configured for Weblogic Servers?
I saw a note, which says the following:
"WebLogic Server does not support multi-domain interaction using either the Administration Console, the weblogic.Admin utility, or WebLogic Ant tasks. This restriction does not, however, explicitly preclude a user written Java application from accessing multiple domains simultaneously."
In my case, I just want to list all the domains, is that possible by using any scripts?
Thanks
AJ

If you use WLS Node Manager and the Config Wizard was used to create the domains, then the list of domains should be in a location like this:
<MIDDLEWARE_HOME>\wlserver_10.3\common\nodemanager\nodemanager.domains
Enterprise Manager Grid Control also has support for multi-domain management of WLS in a console.

REST API: Create Deployment throwing error BadRequest (The specified configuration settings for Settings are invalid. Verify that the service configuration file is a valid XML file, and that role instance counts are specified as positive integers.)

Hi All,
We are trying to access the Create Deployment method stated below
http://msdn.microsoft.com/en-us/library/windowsazure/ee460813
We have uploaded the Package in the blob and browsing the configuration file. We have checked trying to upload manually the package and config file in Azure portal and its working
fine.
Below is the code we have written for creating deployment where "AzureEcoystemCloudService" is our cloud service name where we want to deploy our package. I have also highlighted the XML creation
part.
byte[] bytes =
new byte[fupldConfig.PostedFile.ContentLength + 1];
 fupldConfig.PostedFile.InputStream.Read(bytes, 0, bytes.Length);
string a = Encoding.UTF8.GetString(bytes, 0, bytes.Length);
string base64ConfigurationFile = a.ToBase64();
X509Certificate2 certificate =
CertificateUtility.GetStoreCertificate(ConfigurationManager.AppSettings["thumbprint"].ToString());
HostedService.CreateNewDeployment(certificate,
ConfigurationManager.AppSettings["SubscriptionId"].ToString(),
"2012-03-01", "AzureEcoystemCloudService", Infosys.AzureEcosystem.Entities.Enums.DeploymentSlot.staging,
"AzureEcoystemDeployment",
"http://shubhendustorage.blob.core.windows.net/shubhendustorage/Infosys.AzureEcoystem.Web.cspkg",
"AzureEcoystemDeployment", base64ConfigurationFile,
true, false);
<summary>
/// </summary>
/// <param name="certificate"></param>
/// <param name="subscriptionId"></param>
/// <param name="version"></param>
/// <param name="serviceName"></param>
/// <param name="deploymentSlot"></param>
/// <param name="name"></param>
/// <param name="packageUrl"></param>
/// <param name="label"></param>
/// <param name="base64Configuration"></param>
/// <param name="startDeployment"></param>
/// <param name="treatWarningsAsError"></param>
public static
void CreateNewDeployment(X509Certificate2 certificate,
string subscriptionId,
string version, string serviceName, Infosys.AzureEcosystem.Entities.Enums.DeploymentSlot deploymentSlot,
string name, string packageUrl,
string label, string base64Configuration,
bool startDeployment, bool treatWarningsAsError)
Uri uri = new
Uri(String.Format(Constants.CreateDeploymentUrlTemplate, subscriptionId, serviceName, deploymentSlot.ToString()));
XNamespace wa = Constants.xmlNamespace;
XDocument requestBody =
new XDocument();
String base64ConfigurationFile = base64Configuration;
String base64Label = label.ToBase64();
XElement xName = new
XElement(wa + "Name", name);
XElement xPackageUrl =
new XElement(wa +
"PackageUrl", packageUrl);
XElement xLabel = new
XElement(wa + "Label", base64Label);
XElement xConfiguration =
new XElement(wa +
"Configuration", base64ConfigurationFile);
XElement xStartDeployment =
new XElement(wa +
"StartDeployment", startDeployment.ToString().ToLower());
XElement xTreatWarningsAsError =
new XElement(wa +
"TreatWarningsAsError", treatWarningsAsError.ToString().ToLower());
XElement createDeployment =
new XElement(wa +
"CreateDeployment");
 createDeployment.Add(xName);
 createDeployment.Add(xPackageUrl);
 createDeployment.Add(xLabel);
 createDeployment.Add(xConfiguration);
 createDeployment.Add(xStartDeployment);
 createDeployment.Add(xTreatWarningsAsError);
 requestBody.Add(createDeployment);
 requestBody.Declaration =
new XDeclaration("1.0",
"UTF-8", "no");
XDocument responseBody;
RestApiUtility.InvokeRequest(
 uri, Infosys.AzureEcosystem.Entities.Enums.RequestMethod.POST.ToString(),
HttpStatusCode.Accepted, requestBody, certificate, version,
out responseBody);
<summary>
/// A helper function to invoke a Service Management REST API operation.
/// Throws an ApplicationException on unexpected status code results.
/// </summary>
/// <param name="uri">The URI of the operation to invoke using a web request.</param>
/// <param name="method">The method of the web request, GET, PUT, POST, or DELETE.</param>
/// <param name="expectedCode">The expected status code.</param>
/// <param name="requestBody">The XML body to send with the web request. Use null to send no request body.</param>
/// <param name="responseBody">The XML body returned by the request, if any.</param>
/// <returns>The requestId returned by the operation.</returns>
public static
string InvokeRequest(
Uri uri,
string method,
HttpStatusCode expectedCode,
XDocument requestBody,
X509Certificate2 certificate,
string version,
out XDocument responseBody)
 responseBody =
null;
string requestId = String.Empty;
HttpWebRequest request = (HttpWebRequest)HttpWebRequest.Create(uri);
 request.Method = method;
 request.Headers.Add("x-ms-Version", version);
 request.ClientCertificates.Add(certificate);
 request.ContentType =
"application/xml";
if (requestBody != null)
using (Stream requestStream = request.GetRequestStream())
using (StreamWriter streamWriter =
new StreamWriter(
 requestStream, System.Text.UTF8Encoding.UTF8))
 requestBody.Save(streamWriter,
SaveOptions.DisableFormatting);
HttpWebResponse response;
HttpStatusCode statusCode =
HttpStatusCode.Unused;
try
response = (HttpWebResponse)request.GetResponse();
catch (WebException ex)
// GetResponse throws a WebException for 4XX and 5XX status codes
 response = (HttpWebResponse)ex.Response;
try
 statusCode = response.StatusCode;
if (response.ContentLength > 0)
using (XmlReader reader =
XmlReader.Create(response.GetResponseStream()))
 responseBody =
XDocument.Load(reader);
if (response.Headers !=
null)
 requestId = response.Headers["x-ms-request-id"];
finally
 response.Close();
if (!statusCode.Equals(expectedCode))
throw new
ApplicationException(string.Format(
"Call to {0} returned an error:{1}Status Code: {2} ({3}):{1}{4}",
 uri.ToString(),
Environment.NewLine,
 (int)statusCode,
 statusCode,
 responseBody.ToString(SaveOptions.OmitDuplicateNamespaces)));
return requestId;
But every time we are getting the below error from the line
response = (HttpWebResponse)request.GetResponse();
<Error xmlns="http://schemas.microsoft.com/windowsazure" xmlns:i="http://www.w3.org/2001/XMLSchema-instance">
<Code>BadRequest</Code>
<Message>The specified configuration settings for Settings are invalid. Verify that the service configuration file is a valid XML file, and that role instance counts are specified as positive integers.</Message>
</Error>
Any help is appreciated.
Thanks,
Shubhendu

Please find the request XML I have found it in debug mode
<CreateDeployment xmlns="http://schemas.microsoft.com/windowsazure">
<Name>742d0a5e-2a5d-4bd0-b4ac-dc9fa0d69610</Name>
<PackageUrl>http://shubhendustorage.blob.core.windows.net/shubhendustorage/WindowsAzure1.cspkg</PackageUrl>
<Label>QXp1cmVFY295c3RlbURlcGxveW1lbnQ=</Label>
<Configuration>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</Configuration>
<StartDeployment>true</StartDeployment>
<TreatWarningsAsError>false</TreatWarningsAsError>
</CreateDeployment>
Shubhendu G

The zpool configured in HA Suncluster is corrupted after switching RG

Similar Messages

Maybe you are looking for