TOS Byte and IPSEC Tunnel

I have two sites connected over the Internet via a VPN Tunnell terminated on PIXs at bothe ends. I want to implement QOS on the tunnel. I can mark the packets on the inside of each network and then implemet QOS on the router that connects to the Internet. My concern is that I may loose the setting in the TOS byte when the packet is being encrypted by the PIX. Will the TOS byte be copied to the IPSEC packet even though the tunnel is terminated on the PIX?
[inside net]-PIX- --2620 --- INTERNET ---2620 ---PIX- -- [inside net]

yes, as I know in tunnel mode IPSec copies the TOS to IPSec header. You can also check rfc2401.

Similar Messages

IPSec Tunnel and Making Changes While Up

My main MPLS circuit is down and i have two IPSec tunnels up to my remote sites.
Everything is routing fine but i wanted to add a sub net to my NAT and Tunnels.
Can i add a new subnet to my local network/remote network and save/apply without killing or reseting my active IPSec tunnels?

Reza has interpreted your question in terms of NAT and I agree with him that you should be able to change the NAT configuration without impacting other parts of the router operation and connectivity.
But I read your question as involving both NAT and IPSec tunnels. And I believe that the answer is different when you consider IPSec tunnels. You can go ahead and change the configuration of the tunnels while they are up. But the tunnels negotiated their Security Associations based on the config in place when the tunnels came up. They will continue to use those Security Associations after you make your config change. So if you are changing things like what subnets are in the access list used to identify traffic for IPSec these changes will not take effect until a new Security Association is negotiated. You can either wait for the lifetime to expire and new SA negotiated or your can reset the IPSec tunnels and force a new negotiation. Also note that if you are changing the access list on your end that someone on the other end needs to make a corresponding change on their end.
HTH
Rick

DLSw and IPSEC

Can anybody tell me if you can have a DLSw+ peer and IPSEC tunnel on the same router? We want to utilize DLSw+ on a branch router and use IPSEC across the WAN back to the corporate office?
Has anybody configured this before?
Any lessons learned?
Recomendations?
Thanks!

Hi David,
Yes, multiple customers have deployed this, and it has been tested and measured in specific customer proof of concept labs. The only issue that I'm aware of is that the MTU size requirements are affected by encryption, so be sure to take that into account.
http://www.cisco.com/en/US/tech/tk331/tk336/technologies_tech_note09186a00801d3a9d.shtml
In terms of performance, everyone's traffic is somewhat different, so it's impossible to say for sure. From what I remember of the proof of concept tests, 2600 routers did DLSw+ and software encryption just fine at DS0 rates.
Rgds, Dan

IPSec tunnel and policy NAT question

Hello All!
I have a router acting as VPN gateway on my end and I need to implement NAT translations on my IPSEC tunnel as follows:
1. I need to translate incoming IP address of the remote end of IPSec tunnel to some other IP address on our end
2. I need to translate outgoin IP address of our end of IPSec tunnel to a different IP address
I have impemented following configuration, but for some reason it is not working, I get packets decrypted on my end, but dont have packets encrypted to send to the other end.
Here is the configuration
Remote end crypto interesting ACL:
ip access-list extended crypto-interesting-remote
permit ip host 192.168.1.10 host 10.0.0.10
My end configuration:
interface GigabitEthernet0/0
ip address xxx.xxx.xxx.xxb yyy.yyy.yyy.yyy
ip nat outside
ip virtual-reassembly in
duplex auto
speed auto
crypto map VPN
ip access-list extended crypto-interesting-local
permit ip host 10.0.0.10 host 192.168.1.10
interface GigabitEthernet0/3
ip address 172.16.0.1 255.255.255.0
ip nat inside
ip virtual-reassembly in
speed auto
ip nat inside source static 172.16.0.20 10.0.0.10 (to translate loca IP address to the one on the crypto-interesting list - exposed to the remote peer - it works)
ip nat outside source static 192.168.1.10 192.168.168.10 (to translate remote IP address to some other IP address on our end - not working - I get packets decrypted, but no packets encrypted)
ip route 192.168.168.10 255.255.255.255 gigabitethernet 0/0
ip route 0.0.0.0 0.0.0.0 xxx.xxx.xxx.xxa
All the routes are set, crypto ipsec tunnel is up and working and I am wondering if this is possible to achieve two-way NAT translation ?
Any response highly appreciated!
Thanks!

Figured that out.
The problem was in route
ip route 192.168.168.10 255.255.255.255 gigabitethernet 0/0
should be next-hop IP address instead of interface gigabitethernet0/0
Apparently packet arrives on the interface but does not pass it, when having route like this, becuase there is no one sitting with 192.168.168.10 ip address on the outside

Ipsec tunnel possible with Checkpoint ngx 6.5 and Cisco ISR-dual ISP?

Hi Gurus,
I have a requirement to fulfill in that there are 2 sites that I need to create an ipsec tunnel. A remote site running a Checkpoint ngx 6.5 and a local site with 2 different ISPs and 2 x ISR 29xx routers for both ISP and hardware redundancy. I have only done the vpn setup with one ISR and ISP1 so far.
I am planning to have just 1 ISR (ISR1) and ISP1 being active at any given time. If ISP1 or ISR 1 goes out, all traffic should fail over to ISR2 with ISP2.
is this possible with the ISRs?
Checkpoint does not appear to allow seeing the different ISRs with 2 possible WAN ip addresses with the same encryption domain or 'interesting traffic', so i am not sure if this work at all.
BGP won't be used.
I have looked at ip sla, pbr, and it appears that the best I could achieve would be vpn traffic via ISR1 and ISP1, and could failover only the non vpn traffic to ISR2 and ISP2. Please correct me if I am wrong....many thanks.
Any ideas will be greatly appreciated..
Civicfan

I found the problem but dont know how to fix it now!
Problem is on siteB with using the same ACL name "siteA" in both sequence numbers in cryptomap "outside_map"
crypto map outside_map 9 match address SiteA
crypto map outside_map 9 set peer 212.89.229.xx
crypto map outside_map 9 set transform-set ESP-AES-256-SHA
crypto map outside_map 9 set security-association lifetime seconds 28800
crypto map outside_map 9 set security-association lifetime kilobytes 4608000
crypto map outside_map 10 match address SiteA
crypto map outside_map 10 set peer 212.89.235.yy
crypto map outside_map 10 set transform-set ESP-AES-256-SHA
crypto map outside_map 10 set security-association lifetime seconds 28800
crypto map outside_map 10 set security-association lifetime kilobytes 4608000
If I remove:
no crypto map outside_map 9 match address SiteA
the IPSEC through 2nd ISP on siteA is working correct

IPSEC tunnel with NAT and NetMeeting

I have established an IPSEC tunnel with two Cisco 2621 routers. Clients over the Internet are able to dial into the MCU server, which is behind one of the Cisco 2621 routers configured with NAT but the MCU is not able to call the client. The MCU is able to call any server or client on the LAN however it is not able to call anyone passed the router configured with NAT. Could anyone who has experience with NAT and IPSEC help me out?
Thanks,

The following doc should help...
http://www.cisco.com/warp/public/707/ipsecnat.html

Help on establishing Ipsec tunnel btw 1941 and ASA

   We are creating an Ipsec tunnel over the internet to another site but is not working, could someone help me on what could be happening?
My config:
version 15.1
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname XXXX
boot-start-marker
boot-end-marker
logging buffered 51200 warnings
enable XXXXX
enable password XXXXXX
no aaa new-model
no ipv6 cef
ip source-route
ip cef
ip domain name yourdomain.com
ip name-server XXX.XXX.XXX.XXX
ip name-server XXX.XXX.XXX.XXX
multilink bundle-name authenticated
password encryption aes
crypto pki token default removal timeout 0
crypto pki trustpoint TP-self-signed-4075439344
enrollment selfsigned
subject-name cn=IOS-Self-Signed-Certificate-4075439344
revocation-check none
rsakeypair TP-self-signed-4075439344
crypto pki certificate chain TP-self-signed-4075439344
certificate self-signed 01
3082022B 30820194 A0030201 02020101 300D0609 2A864886 F70D0101 05050030
31312F30 2D060355 04031326 494F532D 53656C66 2D536967 6E65642D 43657274
69666963 6174652D 34303735 34333933 3434301E 170D3131 30393139 30323236
34365A17 0D323030 31303130 30303030 305A3031 312F302D 06035504 03132649
4F532D53 656C662D 5369676E 65642D43 65727469 66696361 74652D34 30373534
33393334 3430819F 300D0609 2A864886 F70D0101 01050003 818D0030 81890281
8100A35E B6AC0BE0 57A53B45 8CF23671 F91A18AC 09F29E6D AEC70F4D EF3BDCD6
269BFDED 44E26A98 7A1ABCAA DB756AFC 719C3D84 8B605C2A 7E99AF79 B72A84BC
89046B2D 967BB775 978EF14D A0BD8036 523B2AE1 1890EB38 BCA3333B 463D1267
22050A4F EAF4985A 7068024A A0425CE7 D3ADF5F5 C02B2941 67C9B654 6A7EF689
049B0203 010001A3 53305130 0F060355 1D130101 FF040530 030101FF 301F0603
551D2304 18301680 1408B59A 57733D6E 157876B3 72A91F28 F8D95BAB D2301D06
03551D0E 04160414 08B59A57 733D6E15 7876B372 A91F28F8 D95BABD2 300D0609
2A864886 F70D0101 05050003 81810094 ED574BFE 95868A5D B539A70F 228CC08C
E26591C2 16DF19AB 7A177688 D7BB1CCB 5CFE4CB6 25F0DDEB 640E6EFA 58636DC0
238750DD 1ACF8902 96BB39B5 5B2F6DEC CB97CF78 23510943 E09801AF 8EB54020
DF496E25 B787126F D1347022 58900537 844EF865 36CB8DBD 79918E4B 76D00196
DD9950CB A40FC91B 4BCDE0DC 1B217A
        quit
license udi pid CISCO1941/K9 sn FTX1539816K
license boot module c1900 technology-package securityk9
username XXXXXXXXXXXXXX
redundancy
crypto isakmp policy 60
encr aes
authentication pre-share
group 2
crypto isakmp key XXXXXXX address XXX.XXX.XXX.XXX
crypto isakmp profile mode
   keyring default
   self-identity address
   match identity host XXX.XXX.XXX.XXX
   initiate mode aggressive
crypto ipsec transform-set VPNbrasil esp-aes esp-sha-hmac
crypto map outside 60 ipsec-isakmp
set peer XXX.XXX.XXX.XXX
set transform-set VPNbrasil
set pfs group2
match address vpnbrazil
interface Tunnel0
ip unnumbered GigabitEthernet0/1
interface Embedded-Service-Engine0/0
no ip address
shutdown
interface GigabitEthernet0/0
description WAN
ip address XXX.XXX.XXX.XXX 255.255.255.248
ip nat outside
no ip virtual-reassembly in
duplex full
speed 100
crypto map outside
interface GigabitEthernet0/1
description Intercon_LAN
ip address XXX.XXX.XXX.XXX 255.255.255.252
ip nat inside
ip virtual-reassembly in
duplex auto
speed auto
crypto map outside
ip forward-protocol nd
ip http server
ip http access-class 23
ip http authentication local
ip http secure-server
ip http timeout-policy idle 60 life 86400 requests 10000
ip nat inside source list 2 interface GigabitEthernet0/1 overload
ip route 0.0.0.0 0.0.0.0 XXX.XXX.XXX.XXX name Internet
ip access-list extended natvpnout
permit ip host XXX.XXX.XXX.XXX any
permit ip any any
ip access-list extended vpnbrazil
permit icmp XXX.XXX.XXX.XXX 0.0.0.255 any
permit icmp any XXX.XXX.XXX.XXX 0.0.0.255
permit ip any any
access-list 1 permit any
access-list 2 permit XXX.XXX.XXX.XXX 0.0.0.1 log
access-list 2 permit XXX.XXX.XXX.XXX 0.0.0.7
access-list 3 permit XXX.XXX.XXX.XXX
access-list 23 permit XXX.XXX.XXX.XXX 0.0.0.7
access-list 23 permit any log
control-plane
b!
line con 0
login local
line aux 0
line 2
no activation-character
no exec
transport preferred none
transport input all
transport output pad telnet rlogin lapb-ta mop udptn v120 ssh
stopbits 1
line vty 0 4
access-class 23 in
privilege level 15
login local
transport input all
telnet transparent
line vty 5
access-class 23 in
privilege level 15
login
transport input all
telnet transparent
line vty 6 15
access-class 23 in
access-class 23 out
privilege level 15
login local
transport input telnet ssh
transport output all
Could someone please help me on what could be wrong? and What tests should I do?
Rds,
Luiz

try a simple configuration w/o isakmp proflies
have a look at this link:
http://www.cisco.com/en/US/products/ps6120/products_configuration_example09186a00805e8c80.shtml

IPSEC tunnel between adsl router (1841-K9) and Windows ISA

Hi. Can anybody point me in the direction of how to achieve this?
Basically weve got a UC500 running CME. We want to send a home worker home with a router and a phone, and allow their router (probably an 1841 with a WIC 1ADSL and K9 pack) to connect to our SBS server with ISA on it and make an IPSEC tunnel.
Thanks!!!

This is now showing up with running ssh over this tunnel. I can get the initial connection, but certain commands are not going through.

IPSEC tunnel Phase 1 and 2

Guys was checking ASA config and we have many IPSEC tunnels
one of the IPSEC tunnel has follwoing
crypto map clientmap 40 set transform-set ESP-3DES-MD5 ESP-3DES-SHA
whats does the second means normally oter IPSEC has
crypto map clientmap 14 set transform-set ESP-3DES-MD5
what is a clientmap anyway will appriciate if someone plz explain

Hi,
The "crypto map" settings belong to the Phase II portion of your VPN tunnel (with some exceptions).
Here you usually define the following paratemers (most common):
1- Protected traffic, "match address" command.
2- Transform-set, integrity and authentication.
3- VPN peer.
So the transform-set "ESP-3DES-SHA" probably is "esp-3des esp-sha-hmac" which means:
ESP with the 3DES encryption algorithm.
ESP with the SHA (HMAC variant) authentication algorithm,
Now, you can have many valid combinations like "ESP-3DES-SHA" and "ESP-3DES-MD5", this would be useful in case you do not know which transform-set the other side of the tunnel has configured (there must be at least one perfect match).
Here is good link to set up L2L tunnels on ASAs:
Configuring LAN-to-LAN VPNs
Hope to help.
Portu.
Please rate any helpful posts

IPSEC Tunnel between JUNIPER (SSG 20) and CISCO PIX 501

I have successfully established the IPSEC tunnel with juniper firewall by using cisco Pix 501 (6.3 version). The problem I am facing, I have network layer connectivity but after time interval I am not able to send the traffic on destination IP address on specific port, but can successfully PING the destination IP. On both firewalls the IPs are permitted for all ports.

Dear Mr.
The same problem has occured with me.

Cisco ASA 5505 Site to site VPN IPSEC tunnel to an Clavister Firewall

Hi,
I have weird problem with a Site to site VPN tunnel from a Cisco ASA 5505 to an Clavister Firewall.
When I restart the Cisco ASA 5505 the tunnel is up and down,up, down, down, and I get all strange messages when I see if the tunnel is up or down with the syntax: show crypto isakmp sa
After a while like 5-10 min the vpn site to site tunnel is up and here is the strange thing happening I have all accesslists and tunnel accesslists right I can only access one remote network (Main site Clavister Firewall) trought the vpn tunnel behind the Cisco ASA 5505, and I have 5 more remote networks that I want to access but only one remote network is working trought the vpn tunnel behind the Cisco ASA. I see that when I do this syntax in ASA: show crypto ipsec sa.
They had a Clavister Firewall before on that site before and now they have a Cisco ASA 5505 and all the rules on the main site thats have the big Clavister Firewall is intact so the problems are in the Cisco ASA 5505.
Here is some logs that ASDM give me about the tunnel issue, but like I said, the tunnel is up and only one remote network is reachable in that tunnel.....
3
Nov 21 2012
07:11:09
713902
Group = 195.149.180.254, IP = 195.149.169.254, Removing peer from correlator table failed, no match!
3
Nov 21 2012
07:11:09
713902
Group = 195.149.180.254, IP = 195.149.169.254, QM FSM error (P2 struct &0xc92462d0, mess id 0x1c6bf927)!
3
Nov 21 2012
07:11:09
713061
Group = 195.149.180.254, IP = 195.149.169.254, Rejecting IPSec tunnel: no matching crypto map entry for remote proxy 0.0.0.0/0.0.0.0/0/0 local proxy 0.0.0.0/0.0.0.0/0/0 on interface outside
5
Nov 21 2012
07:11:09
713119
Group = 195.149.180.254, IP = 195.149.169.254, PHASE 1 COMPLETED
Here is from the syntax: show crypto isakmp sa
Result of the command: "show crypto isakmp sa"
   Active SA: 1
    Rekey SA: 0 (A tunnel will report 1 Active and 1 Rekey SA during rekey)
Total IKE SA: 1
1   IKE Peer: 195.149.180.254
    Type    : L2L             Role    : responder
    Rekey   : no              State   : MM_ACTIVE
Result of the command: "show crypto ipsec sa"
interface: outside
    Crypto map tag: CustomerCryptoMap, seq num: 10, local addr: 213.180.90.29
      access-list arvika_garnisonen permit ip 172.22.65.0 255.255.255.0 192.168.123.0 255.255.255.0
      local ident (addr/mask/prot/port): (172.22.65.0/255.255.255.0/0/0)
      remote ident (addr/mask/prot/port): (192.168.123.0/255.255.255.0/0/0)
      current_peer:195.149.180.254
      #pkts encaps: 2188, #pkts encrypt: 2188, #pkts digest: 2188
      #pkts decaps: 2082, #pkts decrypt: 2082, #pkts verify: 2082
      #pkts compressed: 0, #pkts decompressed: 0
      #pkts not compressed: 2188, #pkts comp failed: 0, #pkts decomp failed: 0
      #pre-frag successes: 0, #pre-frag failures: 0, #fragments created: 0
      #PMTUs sent: 0, #PMTUs rcvd: 0, #decapsulated frgs needing reassembly: 0
      #send errors: 0, #recv errors: 0
      local crypto endpt.: 213.180.67.29, remote crypto endpt.: 195.149.180.254
      path mtu 1500, ipsec overhead 74, media mtu 1500
      current outbound spi: E715B315
    inbound esp sas:
      spi: 0xFAC769EB (4207372779)
         transform: esp-aes-256 esp-sha-hmac no compression
         in use settings ={L2L, Tunnel, PFS Group 5, }
         slot: 0, conn_id: 2879488, crypto-map: CustomerCryptoMap
         sa timing: remaining key lifetime (kB/sec): (38738/2061)
         IV size: 16 bytes
         replay detection support: Y
         Anti replay bitmap:
          0xFFFFFFFF 0xFFFFFFFF
    outbound esp sas:
      spi: 0xE715B315 (3876958997)
         transform: esp-aes-256 esp-sha-hmac no compression
         in use settings ={L2L, Tunnel, PFS Group 5, }
         slot: 0, conn_id: 2879488, crypto-map: CustomerCryptoMap
         sa timing: remaining key lifetime (kB/sec): (38673/2061)
         IV size: 16 bytes
         replay detection support: Y
         Anti replay bitmap:
          0x00000000 0x00000001
And here are my Accesslists and vpn site to site config:
crypto isakmp enable outside
crypto isakmp policy 10
authentication pre-share
encryption aes-256
hash sha
group 5
lifetime 84600
crypto isakmp nat-traversal 40
crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec security-association lifetime seconds 28800
crypto ipsec security-association lifetime kilobytes 4608000
crypto map CustomerCryptoMap 10 match address VPN_Tunnel
crypto map CustomerCryptoMap 10 set pfs group5
crypto map CustomerCryptoMap 10 set peer 195.149.180.254
crypto map CustomerCryptoMap 10 set transform-set ESP-AES-256-SHA
crypto map CustomerCryptoMap interface outside
access-list VPN_Tunnel extended permit ip 172.22.65.0 255.255.255.0 192.168.123.0 255.255.255.0 -------> This is the only remote network I can reach behind the Cisco ASA and the other remote networks dont work..
access-list VPN_Tunnel extended permit ip 172.22.65.0 255.255.255.0 host 10.1.34.5
access-list VPN_Tunnel extended permit ip 172.22.65.0 255.255.255.0 host 10.1.20.76
access-list VPN_Tunnel extended permit ip 172.22.65.0 255.255.255.0 host 62.88.129.221
access-list VPN_Tunnel extended permit ip 172.22.65.0 255.255.255.0 172.22.71.0 255.255.255.0
access-list nonat extended permit ip 172.22.65.0 255.255.255.0 192.168.123.0 255.255.255.0
access-list nonat extended permit ip 172.22.65.0 255.255.255.0 host 10.1.34.5
access-list nonat extended permit ip 172.22.65.0 255.255.255.0 host 10.1.20.76
access-list nonat extended permit ip 172.22.65.0 255.255.255.0 host 62.88.129.221
access-list nonat extended permit ip 172.22.65.0 255.255.255.0 172.22.71.0 255.255.255.0
nat (inside) 0 access-list nonat
All these remote networks are at the Main Site Clavister Firewall.
Best Regards
Michael

Hi,
I'd start by getting the configuration of the remote site related to Local/Remote network configurations and go through them. Even though no changes have been made.
If they are mirror images of eachother already I'd say its probably some problem related to Cisco/Clavister setup
Seems especially wierd to me that one of the error messages includes 0.0.0.0 lines.
I have run into some problems with L2L VPN configurations when our Cisco device just doesnt want to work with the remote end device. In some cases we have confirmed that our networks defined for the L2L VPN are exactly the same and yet when checking debugs on the ASA side we can see the remote end device using totally wrong network masks for the VPN negotiaton and therefore it failed. That problem we corrected with changing the network masks a bit.
Maybe you could try to change the Encryption Domain configurations a bit and test it then.
You could also maybe take some debugs on the Phase2 and see if you get anymore hints as to what could be the problem when only one network is working for the L2L VPN.
- Jouni

The tale of two IPSec Tunnels...

I'm trying to set up an ipsec tunnel at a particular site, and I am just stumped at this point. I have two sites I'm working with, a test site on my bench and the other actual site at another location. Both are ASA 5510's, both are running ASA v8.2(5). The test site has a 3560 off of it, and the production site has a 3750 stack off it. I don't think that part should matter, though.
I used the wizard to create the ipsec configuration on both devices, test and prod, and used the same naming on both to help compare. The test site connects and I can ssh to the 3560 behind it just fine. The production site, however, cannot connect to that 3750 or ping it to save my life. I've poured through the configs on both, and although there are just a couple of differences, the two ASA's are pretty close in configs.
At first I thought it was an acl issue, but I've filtered the logs by syslog id 106023 to watch for denys by access group. When I try to connect to the 3750, I get absolutely no entry in the log that anything is being denied, so I figure that's not it.
Then I thought it may be a routing issue. The one difference between the two sites is that the test site is using eigrp to disperse routes between the asa and switch, while the production site is using static routes. But I also didn't think that would've mattered, because on the static route switch I even put a static route in there to the vpn network which didn't make a difference.
I've also run packet traces on the firewall when doing a ping, and on the test siteI see echo requests and replies. Oon the production site I only see requests, no replies. My encap counters don't increment during pings, but the decap counters do, which make sense.
Other things to note: The test site that works also has a site-to-site vpn up and runnning, so you'll see that in the config as well. Client is Mac OS X 10.6.8, using the Cisco IPSec Config.
I'm hoping someone can look at my configs and tell me if they see anything I'm missing on them that could help solve my problems. I'd appreciate it! Thanks
Test Site that works
Production Site that Doesn't
testasa01-5510# sh run
: Saved
ASA Version 8.2(5)
hostname testasa01-5510
names
interface Ethernet0/0
nameif outside
security-level 0
ip address <outsideif> 255.255.255.240
interface Ethernet0/1
nameif inside
security-level 100
ip address 10.39.194.2 255.255.255.248
interface Ethernet0/2
shutdown
no nameif
no security-level
no ip address
interface Ethernet0/3
shutdown
no nameif
no security-level
no ip address
interface Management0/0
nameif management
security-level 100
no ip address
management-only
boot system disk0:/asa825-k8.bin
ftp mode passive
clock timezone PST -8
clock summer-time PDT recurring
access-list inside_access_in extended permit ip 10.39.0.0 255.255.0.0 any log disable
access-list RemoteAccess_splitTunnelAcl standard permit 10.0.0.0 255.0.0.0
access-list inside_nat0_outbound extended permit ip 10.39.0.0 255.255.0.0 10.0.0.0 255.0.0.0
access-list inside_nat0_outbound extended permit ip 10.0.0.0 255.0.0.0 172.16.139.0 255.255.255.240
access-list outside_cryptomap extended permit ip 10.39.0.0 255.255.0.0 10.0.0.0 255.0.0.0
access-list remoteaccess extended permit ip 172.16.139.0 255.255.255.240 any log disable
tcp-map WSOptions
tcp-options range 24 31 allow
pager lines 24
logging enable
logging asdm informational
mtu outside 1500
mtu inside 1500
mtu management 1500
ip local pool vpn_ip_pool 172.16.139.0-172.16.139.10 mask 255.255.255.0
no failover
icmp unreachable rate-limit 1 burst-size 1
asdm image disk0:/asdm-713.bin
no asdm history enable
arp timeout 14400
global (outside) 100 interface
nat (inside) 0 access-list inside_nat0_outbound
nat (inside) 100 10.39.0.0 255.255.0.0
access-group inside_access_in in interface inside
router eigrp 100
network 10.0.0.0 255.0.0.0
passive-interface default
no passive-interface inside
route outside 0.0.0.0 0.0.0.0 <outsideif> 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
aaa authentication ssh console LOCAL
http server enable
http 10.0.0.0 255.0.0.0 management
http 10.0.0.0 255.0.0.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec transform-set ESP-AES-128-SHA-TRANS esp-aes esp-sha-hmac
crypto ipsec transform-set ESP-AES-128-SHA-TRANS mode transport
crypto ipsec transform-set ESP-AES-128-MD5-TRANS esp-aes esp-md5-hmac
crypto ipsec transform-set ESP-AES-128-MD5-TRANS mode transport
crypto ipsec transform-set ESP-AES-192-SHA-TRANS esp-aes-192 esp-sha-hmac
crypto ipsec transform-set ESP-AES-192-SHA-TRANS mode transport
crypto ipsec transform-set ESP-AES-192-MD5-TRANS esp-aes-192 esp-md5-hmac
crypto ipsec transform-set ESP-AES-192-MD5-TRANS mode transport
crypto ipsec transform-set ESP-AES-256-SHA-TRANS esp-aes-256 esp-sha-hmac
crypto ipsec transform-set ESP-AES-256-SHA-TRANS mode transport
crypto ipsec transform-set ESP-AES-256-MD5-TRANS esp-aes-256 esp-md5-hmac
crypto ipsec transform-set ESP-AES-256-MD5-TRANS mode transport
crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec transform-set ESP-3DES-SHA-TRANS esp-3des esp-sha-hmac
crypto ipsec transform-set ESP-3DES-SHA-TRANS mode transport
crypto ipsec transform-set ESP-3DES-MD5-TRANS esp-3des esp-md5-hmac
crypto ipsec transform-set ESP-3DES-MD5-TRANS mode transport
crypto ipsec transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec transform-set ESP-DES-SHA-TRANS esp-des esp-sha-hmac
crypto ipsec transform-set ESP-DES-SHA-TRANS mode transport
crypto ipsec transform-set ESP-DES-MD5-TRANS esp-des esp-md5-hmac
crypto ipsec transform-set ESP-DES-MD5-TRANS mode transport
crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec security-association lifetime seconds 28800
crypto ipsec security-association lifetime kilobytes 4608000
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set pfs group1
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto map outside_map1 1 match address outside_cryptomap
crypto map outside_map1 1 set pfs group1
crypto map outside_map1 1 set peer 209.242.145.200
crypto map outside_map1 1 set transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto map outside_map1 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map outside_map1 interface outside
crypto isakmp enable outside
crypto isakmp policy 10
authentication crack
encryption aes-256
hash sha
group 2
lifetime 86400
crypto isakmp policy 20
authentication rsa-sig
encryption aes-256
hash sha
group 2
lifetime 86400
crypto isakmp policy 30
authentication pre-share
encryption aes-256
hash sha
group 2
lifetime 86400
crypto isakmp policy 40
authentication crack
encryption aes-192
hash sha
group 2
lifetime 86400
crypto isakmp policy 50
authentication rsa-sig
encryption aes-192
hash sha
group 2
lifetime 86400
crypto isakmp policy 60
authentication pre-share
encryption aes-192
hash sha
group 2
lifetime 86400
crypto isakmp policy 70
authentication crack
encryption aes
hash sha
group 2
lifetime 86400
crypto isakmp policy 80
authentication rsa-sig
encryption aes
hash sha
group 2
lifetime 86400
crypto isakmp policy 90
authentication pre-share
encryption aes
hash sha
group 2
lifetime 86400
crypto isakmp policy 100
authentication crack
encryption 3des
hash sha
group 2
lifetime 86400
crypto isakmp policy 110
authentication rsa-sig
encryption 3des
hash sha
group 2
lifetime 86400
crypto isakmp policy 120
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
crypto isakmp policy 130
authentication crack
encryption des
hash sha
group 2
lifetime 86400
crypto isakmp policy 140
authentication rsa-sig
encryption des
hash sha
group 2
lifetime 86400
crypto isakmp policy 150
authentication pre-share
encryption des
hash sha
group 2
lifetime 86400
crypto isakmp policy 170
authentication pre-share
encryption 3des
hash sha
group 1
lifetime 86400
telnet timeout 5
ssh 10.0.0.0 255.0.0.0 inside
ssh 0.0.0.0 0.0.0.0 management
ssh timeout 60
console timeout 0
management-access inside
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
ntp server <server> source inside
webvpn
group-policy GroupPolicy1 internal
group-policy GroupPolicy1 attributes
vpn-tunnel-protocol IPSec
group-policy RemoteAccess internal
group-policy RemoteAccess attributes
dns-server value 8.8.8.8
vpn-filter value remoteaccess
vpn-tunnel-protocol IPSec
split-tunnel-policy tunnelspecified
split-tunnel-network-list value RemoteAccess_splitTunnelAcl
split-tunnel-all-dns disable
vlan none
tunnel-group RemoteAccess type remote-access
tunnel-group RemoteAccess general-attributes
address-pool vpn_ip_pool
default-group-policy RemoteAccess
tunnel-group RemoteAccess ipsec-attributes
pre-shared-key *****
tunnel-group 111.222.333.444 type ipsec-l2l
tunnel-group 111.222.333.444
general-attributes
default-group-policy GroupPolicy1
tunnel-group 111.222.333.444
ipsec-attributes
pre-shared-key *****
class-map WSOptions-class
match any
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect ip-options
class WSOptions-class
set connection advanced-options WSOptions
policy-map type inspect ip-options ip-options-map
parameters
eool action allow
nop action allow
router-alert action allow
service-policy global_policy global
prompt hostname context
no call-home reporting anonymous
call-home
profile CiscoTAC-1
no active
destination address http https://tools.cisco.com/its/service/oddce/services/DDCEService
destination address email [email protected]
destination transport-method http
subscribe-to-alert-group diagnostic
subscribe-to-alert-group environment
subscribe-to-alert-group inventory periodic monthly
subscribe-to-alert-group configuration periodic monthly
subscribe-to-alert-group telemetry periodic daily
: end
mp01-5510asa# sh run
: Saved
ASA Version 8.2(5)
hostname mp01-5510asa
names
interface Ethernet0/0
nameif inside
security-level 100
ip address 10.29.194.2 255.255.255.252
interface Ethernet0/1
nameif dmz
security-level 50
ip address 172.16.29.1 255.255.255.0
interface Ethernet0/2
description
nameif backup
security-level 0
ip address <backupif> 255.255.255.252
interface Ethernet0/3
description
speed 100
duplex full
nameif outside
security-level 0
ip address <outsideif> 255.255.255.248
interface Management0/0
nameif management
security-level 100
ip address 10.29.199.11 255.255.255.0
management-only
banner login Authorized Use Only
boot system disk0:/asa825-k8.bin
ftp mode passive
clock timezone PST -8
clock summer-time PDT recurring
object-group network DM_INLINE_NETWORK_1
network-object 10.29.1.0 255.255.255.0
network-object 10.29.15.0 255.255.255.0
network-object 10.29.199.0 255.255.255.0
network-object 10.29.200.0 255.255.255.0
network-object 10.29.31.0 255.255.255.0
access-list inside_access_in extended permit ip 10.29.0.0 255.255.0.0 any log warnings
access-list inside_access_in extended permit ip object-group DM_INLINE_NETWORK_1 any log warnings
access-list inside_access_in extended permit ip 192.168.29.0 255.255.255.0 any log warnings
access-list inside_access_in extended permit ip 10.29.32.0 255.255.255.0 any log warnings
access-list outside_access_in extended permit ip any host 50.59.30.116 log warnings
access-list RemoteAccess_splitTunnelAcl standard permit 10.0.0.0 255.0.0.0
access-list inside_nat0_outbound extended permit ip 10.0.0.0 255.0.0.0 10.254.29.0 255.255.255.0 log warnings
access-list remoteaccess extended permit ip 10.254.29.0 255.255.255.0 any log warnings
access-list RemoteAccess2_splitTunnelAcl standard permit 10.29.0.0 255.255.0.0
pager lines 24
logging enable
logging list acl-messages message 106023
logging buffered acl-messages
logging asdm acl-messages
mtu inside 1500
mtu dmz 1500
mtu backup 1500
mtu outside 1500
mtu management 1500
ip local pool vpn_ip_pool3 10.254.29.0-10.254.29.10 mask 255.255.255.0
no failover
icmp unreachable rate-limit 1 burst-size 1
asdm image disk0:/asdm-645.bin
asdm history enable
arp timeout 14400
global (inside) 201 interface
global (dmz) 101 interface
global (backup) 101 interface
global (outside) 101 interface
nat (inside) 0 access-list inside_nat0_outbound
nat (inside) 101 10.29.1.0 255.255.255.0
nat (inside) 101 10.29.15.0 255.255.255.0
nat (inside) 101 10.29.31.0 255.255.255.0
nat (inside) 101 10.29.32.0 255.255.255.0
nat (inside) 101 10.29.199.0 255.255.255.0
nat (inside) 101 10.29.200.0 255.255.255.0
nat (inside) 101 192.168.29.0 255.255.255.0
static (inside,outside) <outsideif> 10.29.15.10 netmask 255.255.255.255
access-group inside_access_in in interface inside
access-group outside_access_in in interface outside
route outside 0.0.0.0 0.0.0.0 50.59.30.113 1 track 1
route backup 0.0.0.0 0.0.0.0 205.179.122.165 254
route management 10.0.0.0 255.0.0.0 10.29.199.1 1
route inside 10.29.0.0 255.255.0.0 10.29.194.1 1
route inside 192.168.29.0 255.255.255.0 10.29.194.1 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
aaa authentication ssh console LOCAL
aaa authentication enable console LOCAL
http server enable
http 10.0.0.0 255.0.0.0 management
http 10.0.0.0 255.0.0.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
sla monitor 100
type echo protocol ipIcmpEcho 74.125.239.16 interface outside
num-packets 3
frequency 10
sla monitor schedule 100 life forever start-time now
crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec security-association lifetime seconds 28800
crypto ipsec security-association lifetime kilobytes 4608000
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set pfs group1
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map outside_map interface outside
crypto isakmp enable outside
crypto isakmp policy 10
authentication pre-share
encryption 3des
hash md5
group 2
lifetime 86400
crypto isakmp policy 30
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
track 1 rtr 100 reachability
telnet timeout 5
ssh 10.0.0.0 255.0.0.0 inside
ssh 10.0.0.0 255.0.0.0 management
ssh timeout 60
console timeout 0
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
ntp server 10.200.1.41 source inside
webvpn
group-policy RemoteAccess internal
group-policy RemoteAccess attributes
dns-server value 8.8.8.8
vpn-filter value remoteaccess
vpn-tunnel-protocol IPSec
split-tunnel-policy tunnelspecified
split-tunnel-network-list value RemoteAccess_splitTunnelAcl
split-tunnel-all-dns disable
vlan none
tunnel-group RemoteAccess type remote-access
tunnel-group RemoteAccess general-attributes
address-pool vpn_ip_pool3
default-group-policy RemoteAccess
tunnel-group RemoteAccess ipsec-attributes
pre-shared-key *****
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum 512
policy-map global_policy
class inspection_default
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect icmp
prompt hostname context
no call-home reporting anonymous
call-home
profile CiscoTAC-1
no active
destination address http https://tools.cisco.com/its/service/oddce/services/DDCEService
destination address email [email protected]
destination transport-method http
subscribe-to-alert-group diagnostic
subscribe-to-alert-group environment
subscribe-to-alert-group inventory periodic monthly
subscribe-to-alert-group configuration periodic monthly
subscribe-to-alert-group telemetry periodic daily
testasa01-5510# sh crypto ipsec sa
interface: outside
    Crypto map tag: SYSTEM_DEFAULT_CRYPTO_MAP, seq num: 65535, local addr: <outsideif>
      local ident (addr/mask/prot/port): (10.0.0.0/255.0.0.0/0/0)
      remote ident (addr/mask/prot/port): (172.16.139.1/255.255.255.255/0/0)
      current_peer: <peer ip>, username: blah
      dynamic allocated peer ip: 172.16.139.1
      #pkts encaps: 0, #pkts encrypt: 0, #pkts digest: 0
      #pkts decaps: 30, #pkts decrypt: 30, #pkts verify: 30
      #pkts compressed: 0, #pkts decompressed: 0
      #pkts not compressed: 0, #pkts comp failed: 0, #pkts decomp failed: 0
      #pre-frag successes: 0, #pre-frag failures: 0, #fragments created: 0
      #PMTUs sent: 0, #PMTUs rcvd: 0, #decapsulated frgs needing reassembly: 0
      #send errors: 0, #recv errors: 0
      local crypto endpt.: <outsideif>/4500, remote crypto endpt.: <peer ip>/37291
      path mtu 1500, ipsec overhead 82, media mtu 1500
      current outbound spi: 0A7F396F
      current inbound spi : E87AF806
    inbound esp sas:
      spi: 0xE87AF806 (3900372998)
         transform: esp-aes esp-sha-hmac no compression
         in use settings ={RA, Tunnel, NAT-T-Encaps, }
         slot: 0, conn_id: 49152, crypto-map: SYSTEM_DEFAULT_CRYPTO_MAP
         sa timing: remaining key lifetime (sec): 3587
         IV size: 16 bytes
         replay detection support: Y
         Anti replay bitmap:
          0x00000000 0x7FFFFFFF
    outbound esp sas:
      spi: 0x0A7F396F (176109935)
         transform: esp-aes esp-sha-hmac no compression
         in use settings ={RA, Tunnel, NAT-T-Encaps, }
         slot: 0, conn_id: 49152, crypto-map: SYSTEM_DEFAULT_CRYPTO_MAP
         sa timing: remaining key lifetime (sec): 3587
         IV size: 16 bytes
         replay detection support: Y
         Anti replay bitmap:
          0x00000000 0x00000001
mp01-5510asa# sh crypto ipsec sa
interface: outside
    Crypto map tag: SYSTEM_DEFAULT_CRYPTO_MAP, seq num: 65535, local addr: <outsideif>
      local ident (addr/mask/prot/port): (10.0.0.0/255.0.0.0/0/0)
      remote ident (addr/mask/prot/port): (10.254.29.1/255.255.255.255/0/0)
      current_peer: <peer ip>, username: blah
      dynamic allocated peer ip: 10.254.29.1
      #pkts encaps: 0, #pkts encrypt: 0, #pkts digest: 0
      #pkts decaps: 51, #pkts decrypt: 51, #pkts verify: 51
      #pkts compressed: 0, #pkts decompressed: 0
      #pkts not compressed: 0, #pkts comp failed: 0, #pkts decomp failed: 0
      #pre-frag successes: 0, #pre-frag failures: 0, #fragments created: 0
      #PMTUs sent: 0, #PMTUs rcvd: 0, #decapsulated frgs needing reassembly: 0
      #send errors: 0, #recv errors: 0
      local crypto endpt.: <outsideif>/4500, remote crypto endpt.: <peer ip>/37291
      path mtu 1500, ipsec overhead 82, media mtu 1500
      current outbound spi: 096265D4
      current inbound spi : F5E4780C
    inbound esp sas:
      spi: 0xF5E4780C (4125390860)
         transform: esp-aes esp-sha-hmac no compression
         in use settings ={RA, Tunnel, NAT-T-Encaps, }
         slot: 0, conn_id: 102400, crypto-map: SYSTEM_DEFAULT_CRYPTO_MAP
         sa timing: remaining key lifetime (sec): 3576
         IV size: 16 bytes
         replay detection support: Y
         Anti replay bitmap:
          0x001FFFFF 0xFFFFFFFF
    outbound esp sas:
      spi: 0x096265D4 (157443540)
         transform: esp-aes esp-sha-hmac no compression
         in use settings ={RA, Tunnel, NAT-T-Encaps, }
         slot: 0, conn_id: 102400, crypto-map: SYSTEM_DEFAULT_CRYPTO_MAP
         sa timing: remaining key lifetime (sec): 3576
         IV size: 16 bytes
         replay detection support: Y
         Anti replay bitmap:
          0x00000000 0x00000001

Config (non working site) looks fine(unless I missed something:)) . You may want to add :
access-list RemoteAccess_splitTunnelAcl standard permit 192.168.29.0 255.255.255.0
Try by taking out vpnfilter : vpn-filter value remoteaccess
To further t-shoot, try using packet tracer from ASA to the client...
https://supportforums.cisco.com/docs/DOC-5796
Thx
MS

Windows 8 and IPSec VPN issues

I have a number of customers that leverage the Cisco IPSec VPN. I can connect to the VPN without any problems but when I attempt to RDP, that fails. I have no RDP or ping or anything. Here are some more symptoms of the issues that I find odd:
Anyconnect works just fine
Fortinet VPN clients work fine
Sonicwall VPN clients work fine
Cisco IPSec VPN client is the only one affected
Cisco IPSec VPN client worked fine for months then just decided it was no longer going to allow RDP or ping
I have duplicated this issue on a half dozen or so laptops
This is on a Windows 8 laptop but I believe I have also experienced this on Windows 7
Just to clarify, the IPSec VPN does succesfully connect. But nothing else works after that. I do understand that AnyConnect is the direction that Cisco would like for people to move towards. Unfortunately, I have quite a few customers that are leveraging the IPSec VPN. I have been through a number of laptops in the last year and every single laptop had a working Cisco IPSec VPN for months....then one day it would just stop passing RDP.
Please somebody tell me that there is a workaround for this. I have played with the IP settings for the Cisco Systems virtual adapter in my network and sharing center. I've modified the binding order. I've compared a routeprint from a working laptop to mine....I'm not sure what else to do. I've uninstalled ALL VPN software and only reinstalled the Cisco VPN. So far the ONLY fix I have found is a clean install of Windows and that solution sucks.

Doing a little more homework on this and I noticed that the tunnel details show no bytes sent or recieved and no packets encrypted, decrypted, or discarded....everything is bypassed. My coworker (who is on Windows 7) is able to launch this VPN and connect to the customer's servers without issues and the tunnel details show all of the appropriate data.

Rejecting IPSec tunnel: no matching crypto map entry for remote proxy on interface outside.

Hi,
I have read a problem where the VPN between an ISP and ourselves started dropping sessions. I have rebuilt the crypto map and tried to dig deeper into my config and some basic troubleshooting while I await the ISP to respond.
Any ideas?
Thanks Steve
https://supportforums.cisco.com/thread/255085
http://www.cisco.com/en/US/products/ps6120/products_tech_note09186a00807e0aca.shtml#solution10
5 Jun 13 15:46:25 713904 IP = 209.183.xxx.xxx, Received encrypted packet with no matching SA, dropping
4 Jun 13 15:46:25 113019 Group = 209.183.xxx.xxx, Username = 209.183.xxx.xxx, IP = 209.183.xxx.xxx, Session disconnected. Session Type: IKE, Duration: 0h:00m:00s, Bytes xmt: 0, Bytes rcv: 0, Reason: crypto map policy not found
3 Jun 13 15:46:25 713902 Group = 209.183.xxx.xxx, IP = 209.183.xxx.xxx, Removing peer from correlator table failed, no match!
3 Jun 13 15:46:25 713902 Group = 209.183.xxx.xxx, IP = 209.183.xxx.xxx, QM FSM error (P2 struct &0xda90f540, mess id 0x76c09eb7)!
3 Jun 13 15:46:25 713061 Group = 209.183.xxx.xxx, IP = 209.183.xxx.xxx, Rejecting IPSec tunnel: no matching crypto map entry for remote proxy 172.16.0.0/255.255.240.0/0/0 local proxy 0.0.0.0/0.0.0.0/0/0 on interface outside
5 Jun 13 15:46:25 713119 Group = 209.183.xxx.xxx, IP = 209.183.xxx.xxx, PHASE 1 COMPLETED
6 Jun 13 15:46:25 113009 AAA retrieved default group policy (DfltGrpPolicy) for user = 209.183.xxx.xxx
6 Jun 13 15:46:25 713172 Group = 209.183.xxx.xxx, IP = 209.183.xxx.xxx, Automatic NAT Detection Status: Remote end is NOT behind a NAT device This end is NOT behind a NAT device

Are you trying to send traffic destined towards the internet from 172.16.0.0/20 via this ASA as well? why? are you inspecting those traffic before being sent out to the internet?
If so, this end also needs to be configured with "any" as well --> crypto ACL needs to mirror image.
access-list outside_1_cryptomap extended permit ip any 172.16.0.0 255.255.240.0
Then you also need NAT on the outside interface, otherwise, traffic from 172.16.0.0/20 is not PATed to a public IP, and won't be able to reach the internet:
nat (outside) 1 172.16.0.0 255.255.240.0

Ipsec tunnel across Avaya 4620 phone terminating to cisco vpn concentrator

I have been asked to test out an avaya 4620 phone with the vpn remote client installed on it for our home users.
Here is my problem. The phone connects fine to my concentrator and I have a successful ipsec tunnel built, however, the phone cannot route back to the corportate network. When I look at the tunnel stats, I see bytes received and none transferred. Also, for the ip address of the remote end, I see the ip address that was assigned to it from my local dsl router. My concentrator is supposed to forward dhcp requests on to my internal dhcp server, but this is not occurring. Has anyone seen this before or know where I should start here? any input will be greatly appreciated, thank you all for your time.

Hello Andrew, I know this thread is a bit old, but I am in the process of trying to setup some 9630's to VPN into my Corp. HQ. which is behind a 5510. the problem I am having is with IKE Phase 2, I keep getting an IKE Phase 2 no Response on the phone and this is what Im getting in the ASA log.
4|Feb 18 2010|09:05:04|113019|||||Group = test, Username = user, IP = 71.161.x.x, Session disconnected. Session Type: IKE, Duration: 0h:00m:01s, Bytes xmt: 0, Bytes rcv: 0, Reason: Phase 2 Mismatch
3|Feb 18 2010|09:05:04|713902|||||Group = test, Username = user, IP = 71.161.x.x, Removing peer from correlator table failed, no match!
3|Feb 18 2010|09:05:04|713902|||||Group = test, Username = user, IP = 71.161.x.x, QM FSM error (P2 struct &0xcc259568, mess id 0x8b0aed6d)!
5|Feb 18 2010|09:05:04|713904|||||Group = test, Username = user, IP = 71.161.x.x, All IPSec SA proposals found unacceptable!
5|Feb 18 2010|09:05:04|713119|||||Group = test, Username = user, IP = 71.161.x.x, PHASE 1 COMPLETED
6|Feb 18 2010|09:05:03|713228|||||Group = test, Username = user, IP = 71.161.x.x, Assigned private IP address 5.5.5.1 to remote user
6|Feb 18 2010|09:05:03|713184|||||Group = test, Username = user, IP = 71.161.x.x, Client Type:   Client Application Version:
5|Feb 18 2010|09:05:03|713130|||||Group = test, Username = user, IP = 71.161.x.x, Received unsupported transaction mode attribute: 6
5|Feb 18 2010|09:05:03|713130|||||Group = test, Username = user, IP = 71.161x.x, Received unsupported transaction mode attribute: 5
6|Feb 18 2010|09:05:03|734001|||||DAP: User user, Addr 71.161.x.x, Connection IPSec: The following DAP records were selected for this connection: DfltAccessPolicy
and this is what I get when I debug cyrpto isakmp
RESERVED != 0, PACKET MAY BE CORRUPTFeb 18 11:51:10 [IKEv1]: Group = test, Username = user, IP = 71.161.x.x, QM FSM error (P2 struct &0xcc4d4748, mess id 0x519ff252)!
Feb 18 11:51:10 [IKEv1 DEBUG]: Group = test, Username = user, IP = 71.161.212.49, IKE QM Responder FSM error history (struct &0xcc4d4748) , : QM_DONE, EV_ERROR-->QM_BLD_MSG2, EV_NEGO_SA-->QM_BLD_MSG2, EV_IS_REKEY-->QM_BLD_MSG2, EV_CONFIRM_SA-->QM_BLD_MSG2, EV_PROC_MSG-->QM_BLD_MSG2, EV_HASH_OK-->QM_BLD_MSG2, NullEvent-->QM_BLD_MSG2, EV_COMP_HASH
Feb 18 11:51:10 [IKEv1 DEBUG]: Group = test, Username = user, IP = 71.161.x.x, sending delete/delete with reason message
Feb 18 11:51:10 [IKEv1]: Group = test, Username = user, IP = 71.161.x.x, Removing peer from correlator table failed, no match!
Feb 18 11:51:10 [IKEv1 DEBUG]: Group = test, Username = user, IP = 71.161.x.x, IKE SA AM:18543029 rcv'd Terminate: state AM_ACTIVE flags 0x00418041, refcnt 1, tuncnt 0
Feb 18 11:51:10 [IKEv1 DEBUG]: Group = test, Username = user, IP = 71.161.x.x, IKE SA AM:18543029 terminating: flags 0x01418001, refcnt 0, tuncnt 0
Feb 18 11:51:10 [IKEv1 DEBUG]: Group = test, Username = user, IP = 71.161.x.x, sending delete/delete with reason message
Feb 18 11:51:10 [IKEv1 DEBUG]: Group = test, Username = user, IP = 71.161.x.x, constructing blank hash payload
Feb 18 11:51:10 [IKEv1 DEBUG]: Group = test, Username = user, IP = 71.161.x.x, constructing IKE delete payload
Feb 18 11:51:10 [IKEv1 DEBUG]: Group = test, Username = user, IP = 71.161.x.x, constructing qm hash payload
Feb 18 11:51:10 [IKEv1]: IP = 71.161.x.x, IKE_DECODE SENDING Message (msgid=2b900ae) with payloads : HDR + HASH (8) + DELETE (12) + NONE (0) total length : 80
BEFORE ENCRYPTION
ISAKMP Header
Initiator COOKIE: 68 fb e0 7a 90 5c d7 10
Responder COOKIE: 29 30 54 18 84 da aa d2
Next Payload: Hash
Version: 1.0
Exchange Type: Informational
Flags: (none)
MessageID: AE00B902
Length: 469762048
Payload Hash
    Next Payload: Delete
    Reserved: 00
    Payload Length: 24
    Data:
      08 4b dc 3d 7c 2b 1b 99 c9 6d 6d 36 14 b9 d1 27
      47 e1 0d d6
Payload Delete
    Next Payload: None
    Reserved: 00
    Payload Length: 28
    DOI: IPsec
    Protocol-ID: PROTO_ISAKMP
    Spi Size: 16
    # of SPIs: 1
    SPI (Hex dump):
      68 fb e0 7a 90 5c d7 10 29 30 54 18 84 da aa d2
ISAKMP Header
Initiator COOKIE: 68 fb e0 7a 90 5c d7 10
Responder COOKIE: 29 30 54 18 84 da aa d2
Next Payload: Hash
Version: 1.0
Exchange Type: Informational
Flags: (Encryption)
MessageID: 02B900AE
Length: 84
RESERVED != 0, PACKET MAY BE CORRUPTFeb 18 11:51:10 [IKEv1]: Ignoring msg to mark SA with dsID 1380352 dead because SA deleted
if you could provide any help it would be greatly appreciated as I have been battling this for a few days now.
thanks,
Paul

TOS Byte and IPSEC Tunnel

Similar Messages

Maybe you are looking for