Transferring Data from RT Processor to FPGA on sbrio9636
Hey,
Im Currently trying to generate a PWM signal and control the Duty Cycle. Ive created the PWM signal in my FPGA which i write to a digital pin. However i want to control the duty cycle of the PWM signal from the RT Processor. I would like to create and control the duty cycle in the RT processor and send that value to the FPGA.How can I do this ?
Thanks
These link could be useful
http://www.ni.com/pdf/manuals/375052c.pdf
http://www.ni.com/pdf/labview/us/compactrio_motor_control_basics.pdf
Similar Messages
-
Passing data from RT host to FPGA through DMA FIFO
Hello,
I am trying to write some data from an RT host to FPGA target using DMA FIFO then process this data and then read them back from the FPGA target to the RT host through another DMA FIFO. I am working on NI PXIe chassis 1062Q, with NI PXIe-8130 embedded RT controller and NI PXIe-7965R FPGA target.
The problem I am facing is that I want to send three different arrays, two of the same size and the third one with different size, and I need the smaller one to be sent to the FPGA first. I tried using flat sequece with two frames in the FPGA VI. In the first frame I read and write the first array in a while loop which is finite (i.e., finite number of iterations). The second frame contains the process of reading and writing the second two arrays (of the same size) in a while loop that can be finite or infinite (according to a control). The problem is that this didn't work. The 2 arrays are displayed on the front panel of the RT host VI and are working fine, however, the array that should have been read in the first sequence doesn't show up on the front panel of the RT host VI. This doesn't make sense because if it is not passed from the host to the fpga and vice versa then the second frame shouldn't have been executed. Note that I am wiring (-1) to the timeout to block the while loop iterations till the passing of each element is complete. Thus the first while loop has 3 iterations only. Could someone help me undersdtand why this happens and how to solve this problem?
I am attaching a picture of both the host and the fpga vi.
Thank you.
Solved!
Go to Solution.
Attachments:
RT host vi.png 102 KB
FPGA vi.png 28 KBNo need to initalize the arrays with values that you will immediately overwrite. Here's what I believe to be equivalent code:
The array outputs should be wired directly to the FPGA FIFO writes. Do not use local variables when you can wire directly.
If you know that you want to transfer the Temp Data Array first, why not make your code do that? Eliminate the sequence structure, and put the functions in the order in which you want them to execute. Use the FPGA reference and error wires to enforce that order. You might consider writing the Temp Data Array, reading it back, then writing the Real and Imag A arrays, to see if that gets you the results you expect. Run the code in simulation (in the project, right-click on the FPGA target and execute on the host with simulated IO) so that you can use execution highlighting and probes to see what is happening. Wire the error wires through and see if you get an error anywhere. Make sure you're not missing something simple like looking at the wrong starting array index. -
Transferring data from a DOS 5.0 (Win 3.1) Computer to a Windows XP Computer - Using Labview
In 1992 my lab purchased a Particle Size Analyzer (Microtrac series 9200) that came with a Compaq computer (DOS 5.0, Win3.1) and a printer. Due to proprietary software restrictions I currently need to keep the analyzer software operating on the DOS computer (to calculate the particle size distribution according to Microtrac's evaluation), although everything else about the system is out-dated. In fact the printer just died last week.
I have been asked to figure out a way to still be able to use the old analyzer software on the DOS computer, but retrieve the data so that it can more quickly (and reliably) be analyzed using current platforms. At the back of the DOS computer the only available port is a parallel port - what Im wondering is how I can transfer data using a parallel port from a DOS computer to another computer with Windows XP? I'd like to use Labview on the 2nd computer (with Windows XP) to retrieve the data - is this possible? And, how do I do this?
Other related questions which you may be able to help with:
(1) What equipment/ type of cord do I need to connect parallel ports?
(2) How do I get a DOS to send signal from the parallel port to the other computer? Do I just need to push "print screen"?
(3) What program do I need on the DOS computer to interface with the parallel port and send signals to the newer computer? Is there a labview program that will run on a DOS computer (Win 3.1)?
Thanks very much in advance for any assistance in this. I do not have a huge amount of computer knowledge so I apologize if any of my terminology is not completely accurate.In dos you can use the copy or print command. More about it here. http://www.computerhope.com/issues/ch000199.htm I have also used a memory stick on dos system. I have USB memstick driver. This works fine. However This will require that your host computer do have a USB port.
Most computers from that time do have one or more serial ports. If you have a free serial port I would have used this and hyperterm on the XP computer. In order to transfer the output file. But before you do this you must set the serial ports on both computers to the same setting. In DOS this is done with the mode coomand http://www.computerhope.com/modehlp.htm
I do not know if this is supported in dos 5.0. But try to type the command msd in dos. MSD is a diagnostic utility to view diagnostic information relating to your computer's hardware setup
Besides which, my opinion is that Express VIs Carthage must be destroyed deleted
(Sorry no Labview "brag list" so far) -
Hello!
I have the following situation:
I have a board with FPGA. I want to receive data from it on TСP/IP.
With FPGA data goes at the speed of 25 MB / s.
Is time to a program written in LabVIEW receive data packets without losses?
Interested in the same maximum packet size that can receive TСP Read Function?
FPGA board - server.
LabVIEW program - client.
The computer uses the powerful.
Operating system-OS Win7.
I would be grateful for your help!Hello,
Here's a great document to check out that provides a lof of info for communicating with RT and FPGA targets. The part that will interest you is the Network Streams >> Raw Ethernet (TCP/UDP) section. This section contains a link to an example project that has a complete TCP Network Stream setup that should give you an idea of how to implement the Network Stream into your project.
NI LabVIEW for CompactRIO Developer’s Guide:
http://www.ni.com/pdf/products/us/fullcriodevguide.pdf
Regards,
Ryan -
Streaming Data between Smart Camera and FPGA?
Is there a way I can stream data between a smart camera (NI 1774) and a FlexRIO FPGA module (PXIe-7961R)? I understand that data from the smart camera can only come from a USB or an Ethernet connection, I intend to plug the camera to the PXI controller (PXIe-8135), the chassis I'm using is PXIe-1082 so the p2p data transfer at 8GB/s should be possible between the controller and the FPGA module.
As a note: The processing I'm trying to do is too computationally intensive so its not possible to do it on the smart camera itself.Hi faisalm88,
This is Emi from NI.
Unfortunately there is no direct streaming between smart camera and FlexRIO FPGA.
(It has to be smart camera -> controller --> FlexRIO FPGA board)
And thus I have a few suggestion for you.
If you can tell me what's your application (does it have to be smart camera? Is the "data" you are talking about image?) ,
I might can come up with even better solution.
1. Do not use smart camera.
The iamge quality of 1774 can be easily replaced with USB web cam.
You can connect the web cam to your PXI controller and transfer data to your FPGA board.
If you are using LabVIEW 2014 and newer, there is function to transfer image data to FPGA.
2. Do not use 8135
Assuming if you are using FlexRIO just to enhance image processing performance,
then if might be better to use CVS
http://sine.ni.com/nips/cds/view/p/lang/ja/nid/212667
It has both FPGA and quadcore processor.
3. Stream image data: 1774 --> 8135 --> 7961R
Let me know what method you want to take
and I can describe them more in detail.
Emi
Emi Nakayama
Applications Engineer, Japan
National Instruments -
I have a VI and an attched .txt data file. Now I want to read the data from the .txt file and display it as an array in the front panel. But the result is not right. Any help?
Attachments:
try2.txt 2 KB
read_array.vi 21 KBThe problem is in the delimiters in your text file. By default, Read From Spreadsheet File.vi expects a tab delimited file. You can specify a delimiter (like a space), but Read From Spreadsheet File.vi has a problem with repeated delimiters: if you specify a single space as a delimiter and Read From Spreadsheet File.vi finds two spaces back-to-back, it stops reading that line. Your file (as I got it from your earlier post) is delimited by 4 spaces.
Here are some of your choices to fix your problem.
1. Change the source file to a tab delimited file. Your VI will then run as is.
2. Change the source file to be delimited by a single space (rather than 4), then wire a string constant containing one space to the delimiter input of Read From Spreadsheet File.vi.
3. Wire a string constant containing 4 spaces to the delimiter input of Read From Spreadsheet File.vi. Then your text file will run as is.
Depending on where your text file comes from (see more comments below), I'd vote for choice 1: a tab delimited text file. It's the most common text output of spreadsheet programs.
Comments for choices 1 and 2: Where does the text file come from? Is it automatically generated or manually generated? Will it be generated multiple times or just once? If it's manually generated or generated just once, you can use any text editor to change 4 spaces to a tab or to a single space. Note: if you want to change it to a tab delimited file, you can't enter a tab directly into a box in the search & replace dialog of many programs like notepad, but you can do a cut and paste. Before you start your search and replace (just in the text window of the editor), press tab. A tab character will be entered. Press Shift-LeftArrow (not Backspace) to highlight the tab character. Press Ctrl-X to cut the tab character. Start your search and replace (Ctrl-H in notepad in Windows 2000). Click into the Find What box. Enter four spaces. Click into the Replace With box. Press Ctrl-V to paste the tab character. And another thing: older versions of notepad don't have search and replace. Use any editor or word processor that does. -
Unable to capture data from Serial port using LVRT2010 in single core pentium 4 machine
I am using application written in Labview using windows Labview
Runtime environment 2010. Application creates a tunnel to intercept data from
Serial port.
My problem is, Currently, I am using single core Pentium
processor. When I am trying to intercept the data between COM1 and COM7 (COM 7
is a virtual port) it is not able to capture data.
When I am running Labview RT environment using dual core
processor machine it is running normally. I wonder whether it could be the compatibility issues with
single core Pentium processor.Hi Magnetica
Are both of the machines running the same runtime engine,
drivers ect?
Have you had RT applications running on this
machine before?
Is the development computer a 64bit machine?
The processor is a supported model (See link below).
http://zone.ni.com/devzone/cda/tut/p/id/8239
Regards
Robert
National Instruments UK & Ireland -
How do I access iCloud Calendar & Contact data from a pre-Lion iMac?
How do I access iCloud Calendar data from my pre-Lion iMac?
Hardware Overview:
Model Name: iMac
Model Identifier: iMac4,1
Processor Name: Intel Core Duo
System 10.7 is not available for this iMac.
Since MobileMe has died, and my other iMac is running 10.7 Lion, iCloud is now the fact in Apple internet data sharing.
I'd like to keep my Address Book (now Contacts in 10.7) and Calendar in sync with my pre-10.7 iMac. How is this done?
Many Thanks,
PBHA nice idea, but ≈$100 for far more than I need. It feels like overkill.
I was thinking something more like a simple CalDAV connection. -
Problem with Runtime Workbench and with sending data from XI to SLD
Hello<br>
<br>
Could I have a little help, a hint in the two following topics:<br>
<br>
1. I run Runtime Workbench -> Component Monitoring -> Display All and I get this error:<br>
<br>
Error during communication with System Landscape Directory: User credentials are invalid or user is denied access<br>
<br>
In filesystem log I can find like this:<br>
<br>
XIRWB.com.sap.aii.mdt.frames.jsp_error [SAPEngine_Application_Thread[impl:3]_40] Fatal: Error during communication with System Landscape Directory: User credentials are invalid or user is denied access<br>
Thrown:<br>
MESSAGE ID: com.sap.aii.rwb.agent.server.rb_LCRAgent.landscapeCommunicationError<br>
com.sap.aii.rwb.exceptions.BuildLandscapeException: Error during communication with System Landscape Directory: User <br>credentials are invalid or user is denied access
at com.sap.aii.rwb.agent.server.SLDAgentBean.convertException(SLDAgentBean.java:1472)
at com.sap.aii.rwb.agent.server.SLDAgentBean.buildSLD(SLDAgentBean.java:773)
at com.sap.aii.rwb.agent.server.SLDAgentBean.provideSld(SLDAgentBean.java:269)
at com.sap.aii.rwb.agent.server.SLDAgentBean.getXIDomain(SLDAgentBean.java:711)
at com.sap.aii.rwb.agent.api.SLDAgentObjectImpl0_0.getXIDomain(SLDAgentObjectImpl0_0.java:375)
at com.sap.aii.rwb.agent.api.SLDAgent_Stub.getXIDomain(SLDAgent_Stub.java:436)
at com.sap.aii.rwb.agent.client.EJBAgent.getXIDomain(EJBAgent.java:255)
at com.sap.aii.rwb.util.web.model.AppMainModel.getSelectedDomain(AppMainModel.java:138)
at com.sap.aii.rwb.util.web.model.DomainRep.build(DomainRep.java:121)
at com.sap.aii.rwb.web.componentmonitoring.model.ObjectIdentificationTree.getComponentTree(ObjectIdentificationTree.java:117)<br>
at jsp_component_monitoring1321125174985._jspService(jsp_component_monitoring1321125174985.java:217)
at com.sap.engine.services.servlets_jsp.server.jsp.JspBase.service(JspBase.java:112)
at com.sap.engine.services.servlets_jsp.server.servlet.JSPServlet.service(JSPServlet.java:544)
at com.sap.engine.services.servlets_jsp.server.servlet.JSPServlet.service(JSPServlet.java:186)
at javax.servlet.http.HttpServlet.service(HttpServlet.java:853)
at com.sap.engine.services.servlets_jsp.server.runtime.RequestDispatcherImpl.doWork(RequestDispatcherImpl.java:321)
at com.sap.engine.services.servlets_jsp.server.runtime.RequestDispatcherImpl.forward(RequestDispatcherImpl.java:377)
at com.sapportals.htmlb.page.PageProcessorServlet.handleRequest(PageProcessorServlet.java:68)
at com.sapportals.htmlb.page.PageProcessorServlet.doGet(PageProcessorServlet.java:29)
at com.sap.aii.rwb.web.componentmonitoring.viewcontroller.CmPageProcessor.doGet(CmPageProcessor.java:27)
at javax.servlet.http.HttpServlet.service(HttpServlet.java:740)
at javax.servlet.http.HttpServlet.service(HttpServlet.java:853)
at com.sap.engine.services.servlets_jsp.server.runtime.RequestDispatcherImpl.doWork(RequestDispatcherImpl.java:321)
at com.sap.engine.services.servlets_jsp.server.runtime.RequestDispatcherImpl.forward(RequestDispatcherImpl.java:377)
at jsp_FC_Secure1321125169379._jspService(jsp_FC_Secure1321125169379.java:24)
at com.sap.engine.services.servlets_jsp.server.jsp.JspBase.service(JspBase.java:112)
at com.sap.engine.services.servlets_jsp.server.servlet.JSPServlet.service(JSPServlet.java:544)
at com.sap.engine.services.servlets_jsp.server.servlet.JSPServlet.service(JSPServlet.java:186)
at javax.servlet.http.HttpServlet.service(HttpServlet.java:853)
at com.sap.engine.services.servlets_jsp.server.HttpHandlerImpl.runServlet(HttpHandlerImpl.java:401)
at com.sap.engine.services.servlets_jsp.server.HttpHandlerImpl.handleRequest(HttpHandlerImpl.java:266)
at com.sap.engine.services.httpserver.server.RequestAnalizer.startServlet(RequestAnalizer.java:387)
at com.sap.engine.services.httpserver.server.RequestAnalizer.startServlet(RequestAnalizer.java:365)
at com.sap.engine.services.httpserver.server.RequestAnalizer.invokeWebContainer(RequestAnalizer.java:944)
at com.sap.engine.services.httpserver.server.RequestAnalizer.handle(RequestAnalizer.java:266)
at com.sap.engine.services.httpserver.server.Client.handle(Client.java:95)
at com.sap.engine.services.httpserver.server.Processor.request(Processor.java:160)
at com.sap.engine.core.service630.context.cluster.session.ApplicationSessionMessageListener.process(ApplicationSessionMessageListener.java:33)
at com.sap.engine.core.cluster.impl6.session.MessageRunner.run(MessageRunner.java:41)
at com.sap.engine.core.thread.impl3.ActionObject.run(ActionObject.java:37)
at java.security.AccessController.doPrivileged(AccessController.java:219)
at com.sap.engine.core.thread.impl3.SingleThread.execute(SingleThread.java:100)
at com.sap.engine.core.thread.impl3.SingleThread.run(SingleThread.java:170)<br>
Root cause:<br>
com.sap.lcr.api.cimclient.UnauthorizedUserException: User credentials are invalid or user is denied access<br>
at com.sap.lcr.api.cimclient.HttpRequestSender.processResponse(HttpRequestSender.java:577)
at com.sap.lcr.api.cimclient.HttpRequestSender.send(HttpRequestSender.java:341)
at com.sap.lcr.api.cimclient.CIMOMClient.send(CIMOMClient.java:280)
at com.sap.lcr.api.cimclient.CIMOMClient.performBatchOperation(CIMOMClient.java:1251)
at com.sap.lcr.api.cimclient.CIMClient.performBatchOperation(CIMClient.java:2268)
at com.sap.aii.utilxi.sld.MRSldProxy.stage1(MRSldProxy.java:989)
at com.sap.aii.utilxi.sld.MRSldProxy.loadComponents(MRSldProxy.java:918)
at com.sap.aii.utilxi.sld.MRSldProxy.loadSld(MRSldProxy.java:907)
at com.sap.aii.utilxi.sld.SubSystemFactory.createSldFromSld(SubSystemFactory.java:373)
at com.sap.aii.utilxi.sld.SubSystemFactory.createSldFromSld(SubSystemFactory.java:434)
at com.sap.aii.rwb.agent.server.SLDAgentBean.buildSLD(SLDAgentBean.java:764)
at com.sap.aii.rwb.agent.server.SLDAgentBean.provideSld(SLDAgentBean.java:269)
at com.sap.aii.rwb.agent.server.SLDAgentBean.getXIDomain(SLDAgentBean.java:711)
at com.sap.aii.rwb.agent.api.SLDAgentObjectImpl0_0.getXIDomain(SLDAgentObjectImpl0_0.java:375)
at com.sap.aii.rwb.agent.api.SLDAgent_Stub.getXIDomain(SLDAgent_Stub.java:436)
at com.sap.aii.rwb.agent.client.EJBAgent.getXIDomain(EJBAgent.java:255)
at com.sap.aii.rwb.util.web.model.AppMainModel.getSelectedDomain(AppMainModel.java:138)
at com.sap.aii.rwb.util.web.model.DomainRep.build(DomainRep.java:121)
at <br>com.sap.aii.rwb.web.componentmonitoring.model.ObjectIdentificationTree.getComponentTree(ObjectIdentificationTree.java:117)
at jsp_component_monitoring1321125174985._jspService(jsp_component_monitoring1321125174985.java:217)
at com.sap.engine.services.servlets_jsp.server.jsp.JspBase.service(JspBase.java:112)
at com.sap.engine.services.servlets_jsp.server.servlet.JSPServlet.service(JSPServlet.java:544)
at com.sap.engine.services.servlets_jsp.server.servlet.JSPServlet.service(JSPServlet.java:186)
at javax.servlet.http.HttpServlet.service(HttpServlet.java:853)
at com.sap.engine.services.servlets_jsp.server.runtime.RequestDispatcherImpl.doWork(RequestDispatcherImpl.java:321)
at com.sap.engine.services.servlets_jsp.server.runtime.RequestDispatcherImpl.forward(RequestDispatcherImpl.java:377)
at com.sapportals.htmlb.page.PageProcessorServlet.handleRequest(PageProcessorServlet.java:68)
at com.sapportals.htmlb.page.PageProcessorServlet.doGet(PageProcessorServlet.java:29)
at com.sap.aii.rwb.web.componentmonitoring.viewcontroller.CmPageProcessor.doGet(CmPageProcessor.java:27)
at javax.servlet.http.HttpServlet.service(HttpServlet.java:740)
at javax.servlet.http.HttpServlet.service(HttpServlet.java:853)
at com.sap.engine.services.servlets_jsp.server.runtime.RequestDispatcherImpl.doWork(RequestDispatcherImpl.java:321)
at com.sap.engine.services.servlets_jsp.server.runtime.RequestDispatcherImpl.forward(RequestDispatcherImpl.java:377)
at jsp_FC_Secure1321125169379._jspService(jsp_FC_Secure1321125169379.java:24)
at com.sap.engine.services.servlets_jsp.server.jsp.JspBase.service(JspBase.java:112)
at com.sap.engine.services.servlets_jsp.server.servlet.JSPServlet.service(JSPServlet.java:544)
at com.sap.engine.services.servlets_jsp.server.servlet.JSPServlet.service(JSPServlet.java:186)
at javax.servlet.http.HttpServlet.service(HttpServlet.java:853)
at com.sap.engine.services.servlets_jsp.server.HttpHandlerImpl.runServlet(HttpHandlerImpl.java:401)
at com.sap.engine.services.servlets_jsp.server.HttpHandlerImpl.handleRequest(HttpHandlerImpl.java:266)
at com.sap.engine.services.httpserver.server.RequestAnalizer.startServlet(RequestAnalizer.java:387)
at com.sap.engine.services.httpserver.server.RequestAnalizer.startServlet(RequestAnalizer.java:365)
at com.sap.engine.services.httpserver.server.RequestAnalizer.invokeWebContainer(RequestAnalizer.java:944)
at com.sap.engine.services.httpserver.server.RequestAnalizer.handle(RequestAnalizer.java:266)
at com.sap.engine.services.httpserver.server.Client.handle(Client.java:95)
at com.sap.engine.services.httpserver.server.Processor.request(Processor.java:160)
at com.sap.engine.core.service630.context.cluster.session.ApplicationSessionMessageListener.process(ApplicationSessionMessageListener.java:33)
at com.sap.engine.core.cluster.impl6.session.MessageRunner.run(MessageRunner.java:41)
at com.sap.engine.core.thread.impl3.ActionObject.run(ActionObject.java:37)
at java.security.AccessController.doPrivileged(AccessController.java:219)
at com.sap.engine.core.thread.impl3.SingleThread.execute(SingleThread.java:100)
at com.sap.engine.core.thread.impl3.SingleThread.run(SingleThread.java:170)
<br>
<br>
<br>
I don't know what is wrong.<br>
I have configured:<br>
- SLDCHECK work properly,<br>
- none of the users PI* type not lock,<br>
- password to the PI* users in exchangeProfile entered correctly,<br>
- In VA in the JCo RFC Provider I have properly configure: AI_RUNTIME_JCOSERVER, LCRSAPRFC, SAPSLDAPI_SID - from the ABAP I can connect to this programs ID<br>
- In VA in SLD Data Supplier I have properly configure bookmarks HTTP Settings and CIM Client Generation Settings. CIMClient Test is OK<br>
<br>
I do not know what else I can see, what else I have properly configured ... I looked at the notes:: 936093 jak i 721548...<br>
<br>
<br>
2. I can't send data from XI to SLD, ie makes me a system definition in Web As Abap and Web as Java but nothing appear to me in Exchange Infrastructure. Exchange Infrastructure is empty - what is wrong??<br>
I carried out the recommendation by 764176 and 1031321 notes<br>
<br>
I restart below applications (no effect)...<br>
com.sap.xi.directory (Integration Builder/Configuration)<br>
com.sap.aii.af.app (Adapter Engine)<br>
com.sap.xi.rwb (Runtime Workbench)<br>
com.sap.xi.repository (Integration Builder/Design)<br>
<br>
Can I ask for help and guidance in these topics?<br>
<br>
Regards<br>
RP<br>I increased logging in the NWA (Configuration -> Log Configuration) - and increased the some things here to log ALL. So that from the NWA (Monitoring -> Logs and Traces) I see a little more information (but does not follow that with which the user is a problem).<br>
<br>
Here are some interesting logs ...<br>
I was most rash or irritation of those that say about the lack of credentials u2013 I must use Viusal Administrator and set good service ...<br>
<br>
What do I have done:<br>
In the Visual Administrator -> Cluster -> Server -> Services -> SLD Data Supplier<br>
I have set in the HTTP Settings tab the host and port SLD, the user name and password is also entered as it is in the SLD. To be sure, already have set for the user entered here such roles as:<br>
SAP_SLD_ADMINISTRATOR<br>
SAP_SLD_CONFIGURATOR<br>
SAP_SLD_DEVELOPER<br>
SAP_SLD_GUEST<br>
SAP_SLD_ORGANIZER<br>
Maybe we are talking in this place about a different user?<br>
<br>
Similarly, when it comes to tab CIM Client Generation Settings - here's all the same thing done. CIMClient test shows that everything is OK.<br>
When I click the button: This trigger the transfer of data to the SLD gets the message that everything was shipped correctly. Indeed, I received an instance of JAVA in SLD<br>
Also clicked on this icon: Assign application roles to user group - got information that everything is attached properly.<br>
<br>
By ABAP side, the connections: INTEGRATION_DIRECTORY_HMI, SAPSLDAPI, LCRSAPRFC, AI_RUNTIME_JCOSERVER and AI_DIRECTORY_JCOSERVER work correctly, ie I can perform the test - which means that programs ID are properly positioned in JCO Provider in VA.<br>
<br>
Puzzling is this message:<br>
The SLD data is inconsistent.<br>
<br>
Strange also that the message (from the ABAP everything is available in SMGW no errors):<br>
Connect to SAP gateway failed<br>
<br>
And what is this error:<br>
<br>
could not sync ExchangeProfile: <br>
Thrown:<br>
com.sap.rprof.dbprofiles.DBException: Connect to SAP gateway failed<br>
Connect_PM TYPE=A ASHOST=saptest2 SYSNR=60 GWHOST=saptest2 GWSERV=sapgw60 PCS=1<br>
<br>
LOCATION CPIC (TCP/IP) on local host with Unicode<br>
ERROR partner 'saptest2:sapgw60' not reached<br>
TIME Thu Feb 23 07:28:07 201<br>
RELEASE 700<br>
COMPONENT NI (network interface)<br>
VERSION 38<br>
RC -10<br>
MODULE nixxi.cpp<br>
LINE 2513<br>
DETAIL NiPConnect<br>
SYSTEM CALL connect<br>
ERRNO 79<br>
ERRNO TEXT A remote host refused an attempted connect operation.<br>
COUNTER 2<br>
<br>
<br>
Below is a list of some interesting logs ...<br>
<br>
###########<br>
<br>
Insufficient permissions for getting SLD access information. You can add permissions for your application via the SLD service in the 'Visual Administrator'.<br>
<br>
#############<br>
<br>
SLD is not accessible. Check SLD Data Supplier service settings.<br>
<br>
###########<br>
<br>
"Warning","2012-02-22","07:53:50:986","Data get on com.sap.sldserv.data.GetSAPBCCentralServiceInstance class processing failed. htThe SLD data is inconsistent. This is an internal processing problem.","/System/Server/SLDService","com.sap.sldserv.DataCollector","n/a","saptest2","Server 0 60_36694",<br>
<br>
#########<br>
<br>
com.sap.lcr.api.cimclient.UnauthorizedUserException: User credentials are invalid or user is denied access<br>
<br>
################<br>
<br>
Full Message Text
CPA Cache not updated with directory data, due to: Couldn't open Directory URL (http://saptest2.unx.era.pl:56000/dir/hmi_cache_refresh_service/ext?method=CacheRefresh&mode=C&consumer=af.xit.saptest2), due to: HTTP 503: Service Unavailable
<br>
##################<br>
<br>
Full Message Text <br>
<br>
could not sync ExchangeProfile: <br>
Thrown:<br>
com.sap.rprof.dbprofiles.DBException: Connect to SAP gateway failed<br>
Connect_PM TYPE=A ASHOST=saptest2 SYSNR=60 GWHOST=saptest2 GWSERV=sapgw60 PCS=1<br>
<br>
LOCATION CPIC (TCP/IP) on local host with Unicode<br>
ERROR partner 'saptest2:sapgw60' not reached<br>
TIME Thu Feb 23 07:28:07 201<br>
RELEASE 700<br>
COMPONENT NI (network interface)<br>
VERSION 38<br>
RC -10<br>
MODULE nixxi.cpp<br>
LINE 2513<br>
DETAIL NiPConnect<br>
SYSTEM CALL connect<br>
ERRNO 79<br>
ERRNO TEXT A remote host refused an attempted connect operation.<br>
COUNTER 2<br>
<br>
Connect_PM TYPE=A ASHOST=saptest2 SYSNR=60 GWHOST=saptest2 GWSERV=sapgw60 PCS=1<br>
<br>
LOCATION CPIC (TCP/IP) on local host with Unicode<br>
ERROR partner 'saptest2:sapgw60' not reached<br>
TIME Thu Feb 23 07:28:07 201<br>
RELEASE 700<br>
COMPONENT NI (network interface)<br>
VERSION 38<br>
RC -10<br>
MODULE nixxi.cpp<br>
LINE 2513<br>
DETAIL NiPConnect<br>
SYSTEM CALL connect<br>
ERRNO 79<br>
ERRNO TEXT A remote host refused an attempted connect operation.<br>
COUNTER 2<br>
<br>
at com.sap.mw.jco.MiddlewareJRfc.generateJCoException(MiddlewareJRfc.java:457)<br>
at com.sap.mw.jco.MiddlewareJRfc$Client.connect(MiddlewareJRfc.java:1015)<br>
at com.sap.mw.jco.JCO$Client.connect(JCO.java:3238)<br>
at com.sap.rprof.dbprofiles.DBProfiles.getProfile(DBProfiles.java:101)<br>
at com.sap.rprof.dbprofiles.RemoteProfile.readRemoteProfileFromMedia(RemoteProfile.java:1288)<br>
at com.sap.rprof.dbprofiles.RemoteProfile.getRemoteProfileFromFactory(RemoteProfile.java:195)<br>
at com.sap.aii.utilxi.prop.rprof.ExchangeProfilePropertySource.readProfile(ExchangeProfilePropertySource.java:177)<br>
at com.sap.aii.utilxi.prop.rprof.ExchangeProfilePropertySource.sync(ExchangeProfilePropertySource.java:165)<br>
at com.sap.aii.utilxi.misc.api.AIIProperties.sync(AIIProperties.java:582)<br>
at com.sap.aii.af.service.sld.SLDAccess.syncExchangeProfile(SLDAccess.java:43)<br>
at com.sap.aii.adapter.xi.ms.SLDReader.fire(SLDReader.java:52)<br>
at com.sap.aii.adapter.xi.ms.SLDReader.run(SLDReader.java:167)<br>
at com.sap.engine.core.thread.impl3.ActionObject.run(ActionObject.java:37)<br>
at java.security.AccessController.doPrivileged(AccessController.java:219)<br>
at com.sap.engine.core.thread.impl3.SingleThread.execute(SingleThread.java:100)<br>
at com.sap.engine.core.thread.impl3.SingleThread.run(SingleThread.java:170)<br>
<br>
##############<br>
<br>
Full Message Text <br>
<br>
Import of software component version list from component repository failed<br>
Thrown:<br>
com.sap.lcr.api.cimclient.LcrException: User credentials are invalid or user is denied access<br>
at com.sap.lcr.api.cimclient.HttpRequestSender.processResponse(HttpRequestSender.java:577)<br>
at com.sap.lcr.api.cimclient.HttpRequestSender.send(HttpRequestSender.java:341)<br>
at com.sap.lcr.api.cimclient.CIMOMClient.sendImpl(CIMOMClient.java:198)<br>
at com.sap.lcr.api.cimclient.CIMOMClient.send(CIMOMClient.java:146)<br>
at com.sap.lcr.api.cimclient.CIMOMClient.enumerateInstancesImpl(CIMOMClient.java:443)<br>
at com.sap.lcr.api.cimclient.CIMOMClient.enumerateInstances(CIMOMClient.java:747)<br>
at com.sap.lcr.api.cimclient.CIMClient.enumerateInstances(CIMClient.java:980)<br>
at com.sap.lcr.api.sapmodel.JavaCIMObjectAccessor.enumerateInstances(JavaCIMObjectAccessor.java:211)<br>
at com.sap.lcr.api.sapmodel.SAP_SoftwareComponentAccessor.enumerateInstances(SAP_SoftwareComponentAccessor.java:204)<br>
at com.sap.lcr.api.sapmodel.SAP_SoftwareComponentAccessor.enumerateSAP_SoftwareComponentInstances(SAP_SoftwareComponentAccessor.java:239)<br>
at com.sap.aii.ibrep.server.sldaccess.interfaces.CRAccess.getSwcLinks(CRAccess.java:82)<br>
at com.sap.aii.ibrep.server.extobjects.SwcAccessor.getEoLinks(SwcAccessor.java:59)<br>
at com.sap.aii.ib.server.extobjects.EOAServiceImpl.getEoLinks(EOAServiceImpl.java:75)<br>
at com.sap.aii.ib.sbeans.extobjects.EOAServiceBean.getEoLinks(EOAServiceBean.java:66)<br>
at com.sap.aii.ib.sbeans.extobjects.EOAServiceRemoteObjectImpl1_0.getEoLinks(EOAServiceRemoteObjectImpl1_0.java:527)<br>
at com.sap.aii.ib.sbeans.extobjects.EOAServiceRemoteObjectImpl1_0p4_Skel.dispatch(EOAServiceRemoteObjectImpl1_0p4_Skel.java:232)<br>
at com.sap.engine.services.rmi_p4.DispatchImpl._runInternal(DispatchImpl.java:320)<br>
at com.sap.engine.services.rmi_p4.DispatchImpl._run(DispatchImpl.java:198)<br>
at com.sap.engine.services.rmi_p4.server.P4SessionProcessor.request(P4SessionProcessor.java:129)<br>
at com.sap.engine.core.service630.context.cluster.session.ApplicationSessionMessageListener.process(ApplicationSessionMessageListener.java:33)<br>
at com.sap.engine.core.cluster.impl6.session.MessageRunner.run(MessageRunner.java:41)<br>
at com.sap.engine.core.thread.impl3.ActionObject.run(ActionObject.java:37)<br>
at java.security.AccessController.doPrivileged(AccessController.java:219)<br>
at com.sap.engine.core.thread.impl3.SingleThread.execute(SingleThread.java:100)<br>
at com.sap.engine.core.thread.impl3.SingleThread.run(SingleThread.java:170)<br>
<br>
##############<br>
<br>
Full Message Text <br>
<br>
An exception was thrown in the UME/ABAP user management connector. Message: Connect to SAP gateway failed<br>
Connect_PM TYPE=A ASHOST=localhost SYSNR=60 GWHOST=localhost GWSERV=sapgw60 PCS=1<br>
<br>
LOCATION CPIC (TCP/IP) on local host with Unicode<br>
ERROR partner '127.0.0.1:sapgw60' not reached<br>
TIME Thu Feb 23 07:28:06 201<br>
RELEASE 700<br>
COMPONENT NI (network interface)<br>
VERSION 38<br>
RC -10<br>
MODULE nixxi.cpp<br>
LINE 2513<br>
DETAIL NiPConnect<br>
SYSTEM CALL connect<br>
ERRNO 79<br>
ERRNO TEXT A remote host refused an attempted connect operation.<br>
COUNTER 16<br>
<br> -
Getting error While loading data from ERP integrator to HFM
Hello,
We are getting the following error while loading the data from ERPI to HFM.
2013-12-31 22:44:54,133 INFO [AIF]: ERPI Process Start, Process ID: 300
2013-12-31 22:44:54,137 INFO [AIF]: ERPI Logging Level: DEBUG (5)
2013-12-31 22:44:54,139 INFO [AIF]: ERPI Log File: C:\Windows\TEMP\/aif_501_300.log
2013-12-31 22:44:54,141 INFO [AIF]: Jython Version: 2.5.1 (Release_2_5_1:6813, Sep 26 2009, 13:47:54)
[Java HotSpot(TM) 64-Bit Server VM (Oracle Corporation)]
2013-12-31 22:44:54,143 INFO [AIF]: Java Platform: java1.7.0_25
2013-12-31 22:44:56,821 INFO [AIF]: COMM Process Periods - Insert Periods - START
2013-12-31 22:44:56,828 DEBUG [AIF]:
SELECT l.SOURCE_LEDGER_ID
,l.SOURCE_LEDGER_NAME
,l.SOURCE_COA_ID
,l.CALENDAR_ID
,'0' SETID
,l.PERIOD_TYPE
,NULL LEDGER_TABLE_NAME
FROM AIF_BALANCE_RULES br
,AIF_COA_LEDGERS l
WHERE br.RULE_ID = 27
AND l.SOURCE_SYSTEM_ID = br.SOURCE_SYSTEM_ID
AND l.SOURCE_LEDGER_ID = br.SOURCE_LEDGER_ID
2013-12-31 22:44:56,834 DEBUG [AIF]:
INSERT INTO AIF_PROCESS_PERIODS (
PROCESS_ID
,PERIODKEY
,PERIOD_ID
,ADJUSTMENT_PERIOD_FLAG
,GL_PERIOD_YEAR
,GL_PERIOD_NUM
,GL_PERIOD_NAME
,GL_PERIOD_CODE
,GL_EFFECTIVE_PERIOD_NUM
,YEARTARGET
,PERIODTARGET
,IMP_ENTITY_TYPE
,IMP_ENTITY_ID
,IMP_ENTITY_NAME
,TRANS_ENTITY_TYPE
,TRANS_ENTITY_ID
,TRANS_ENTITY_NAME
,PRIOR_PERIOD_FLAG
,SOURCE_LEDGER_ID
SELECT DISTINCT brl.LOADID PROCESS_ID
,pp.PERIODKEY PERIODKEY
,prd.PERIOD_ID
,COALESCE(prd.ADJUSTMENT_PERIOD_FLAG, 'N') ADJUSTMENT_PERIOD_FLAG
,COALESCE(prd.YEAR,0) GL_PERIOD_YEAR
,COALESCE(prd.PERIOD_NUM,0) GL_PERIOD_NUM
,prd.PERIOD_NAME GL_PERIOD_NAME
,COALESCE(prd.PERIOD_CODE, CAST(COALESCE(prd.PERIOD_NUM,0) AS VARCHAR(38))) GL_PERIOD_CODE
,(COALESCE(prd.YEAR,0) * 10000 + COALESCE(prd.PERIOD_NUM,0)) GL_EFFECTIVE_PERIOD_NUM
,COALESCE(ppa.YEARTARGET, pp.YEARTARGET) YEARTARGET
,COALESCE(ppa.PERIODTARGET, pp.PERIODTARGET) PERIODTARGET
,'PROCESS_BAL_IMP' IMP_ENTITY_TYPE
,(COALESCE(prd.YEAR,0) * 10000 + COALESCE(prd.PERIOD_NUM,0)) IMP_ENTITY_ID
,prd.PERIOD_NAME IMP_ENTITY_NAME
,'PROCESS_BAL_TRANS' TRANS_ENTITY_TYPE
,(COALESCE(prd.YEAR,0) * 10000 + COALESCE(prd.PERIOD_NUM,0)) TRANS_ENTITY_ID
,pp.PERIODDESC TRANS_ENTITY_NAME
,'N' PRIOR_PERIOD_FLAG
,1 SOURCE_LEDGER_ID
FROM (
AIF_BAL_RULE_LOADS brl
INNER JOIN TPOVCATEGORY pc
ON pc.CATKEY = brl.CATKEY
INNER JOIN TPOVPERIOD_FLAT_V pp
ON pp.PERIODFREQ = pc.CATFREQ
AND pp.PERIODKEY >= brl.START_PERIODKEY
AND pp.PERIODKEY <= brl.END_PERIODKEY
LEFT OUTER JOIN TPOVPERIODADAPTOR_FLAT_V ppa
ON ppa.PERIODKEY = pp.PERIODKEY
AND ppa.PERIODFREQ = pp.PERIODFREQ
AND ppa.INTSYSTEMKEY = 'FMTEST2'
INNER JOIN AIF_GL_PERIODS_STG prd
ON prd.SOURCE_SYSTEM_ID = 3
AND prd.CALENDAR_ID IN ('10000')
AND prd.SETID = '0'
AND prd.PERIOD_TYPE = 'Month'
AND prd.ADJUSTMENT_PERIOD_FLAG = 'N'
AND prd.START_DATE > pp.PRIORPERIODKEY
AND prd.START_DATE <= pp.PERIODKEY
WHERE brl.LOADID = 300
ORDER BY pp.PERIODKEY
,GL_EFFECTIVE_PERIOD_NUM
2013-12-31 22:44:56,915 INFO [AIF]: COMM Process Periods - Insert Periods - END
2013-12-31 22:44:56,945 INFO [AIF]: COMM Process Periods - Insert Process Details - START
2013-12-31 22:44:56,952 DEBUG [AIF]:
INSERT INTO AIF_PROCESS_DETAILS (
PROCESS_ID
,ENTITY_TYPE
,ENTITY_ID
,ENTITY_NAME
,ENTITY_NAME_ORDER
,TARGET_TABLE_NAME
,EXECUTION_START_TIME
,EXECUTION_END_TIME
,RECORDS_PROCESSED
,STATUS
,LAST_UPDATED_BY
,LAST_UPDATE_DATE
SELECT PROCESS_ID
,ENTITY_TYPE
,ENTITY_ID
,ENTITY_NAME
,ENTITY_NAME_ORDER
,'AIF_EBS_GL_BALANCES_STG' TARGET_TABLE_NAME
,CURRENT_TIMESTAMP EXECUTION_START_TIME
,NULL EXECUTION_END_TIME
,0 RECORDS_PROCESSED
,'PENDING' STATUS
,'native://DN=cn=911,ou=People,dc=css,dc=hyperion,dc=com?USER' LAST_UPDATED_BY
,CURRENT_TIMESTAMP LAST_UPDATE_DATE
FROM (
SELECT DISTINCT PROCESS_ID
,IMP_ENTITY_TYPE ENTITY_TYPE
,IMP_ENTITY_ID ENTITY_ID
,IMP_ENTITY_NAME ENTITY_NAME
,(COALESCE(SOURCE_LEDGER_ID,0) * 100000000 + GL_EFFECTIVE_PERIOD_NUM) ENTITY_NAME_ORDER
FROM AIF_PROCESS_PERIODS
WHERE PROCESS_ID = 300
) q
ORDER BY ENTITY_NAME_ORDER
2013-12-31 22:44:56,963 DEBUG [AIF]:
INSERT INTO AIF_PROCESS_DETAILS (
PROCESS_ID
,ENTITY_TYPE
,ENTITY_ID
,ENTITY_NAME
,ENTITY_NAME_ORDER
,TARGET_TABLE_NAME
,EXECUTION_START_TIME
,EXECUTION_END_TIME
,RECORDS_PROCESSED
,STATUS
,LAST_UPDATED_BY
,LAST_UPDATE_DATE
SELECT PROCESS_ID
,ENTITY_TYPE
,ENTITY_ID
,ENTITY_NAME
,ENTITY_NAME_ORDER
,'TDATASEG' TARGET_TABLE_NAME
,CURRENT_TIMESTAMP EXECUTION_START_TIME
,NULL EXECUTION_END_TIME
,0 RECORDS_PROCESSED
,'PENDING' STATUS
,'native://DN=cn=911,ou=People,dc=css,dc=hyperion,dc=com?USER' LAST_UPDATED_BY
,CURRENT_TIMESTAMP LAST_UPDATE_DATE
FROM (
SELECT PROCESS_ID
,TRANS_ENTITY_TYPE ENTITY_TYPE
,MIN(TRANS_ENTITY_ID) ENTITY_ID
,TRANS_ENTITY_NAME ENTITY_NAME
,MIN(COALESCE(SOURCE_LEDGER_ID,0) * 100000000 + GL_EFFECTIVE_PERIOD_NUM) ENTITY_NAME_ORDER
FROM AIF_PROCESS_PERIODS
WHERE PROCESS_ID = 300
AND PRIOR_PERIOD_FLAG = 'N'
GROUP BY PROCESS_ID
,TRANS_ENTITY_TYPE
,TRANS_ENTITY_NAME
) q
ORDER BY ENTITY_NAME_ORDER
2013-12-31 22:44:56,970 INFO [AIF]: COMM Process Periods - Insert Process Details - END
2013-12-31 22:44:57,407 DEBUG [AIF]: EBS/FS GL Balances Print Variables - Printing Variables - START
2013-12-31 22:44:57,408 DEBUG [AIF]:
p_process_id: 300
p_sql_db_type: ORACLE
p_partitionkey: 12
p_rule_id: 27
p_source_system_id: 3
p_application_id: 26
p_target_application_type: HFM
p_is_multi_currency: true
p_data_load_method: CLASSIC_VIA_EPMI
p_bal_balance_method_code: STANDARD
p_bal_ledger_group_code: SINGLE
p_bal_amount_type: MONETARY
p_prd_entity_name: JAN-13
p_prd_period_id: 135
p_prd_gl_period_name: JAN-13
p_prd_source_ledger_id: 1
p_prd_source_coa_id: 101
p_source_ledger_id: 1
p_source_coa_id: 101
p_bal_actual_flag: A
p_bal_seg_column_name: SEGMENT1
p_max_ccid_loaded_to_stg: 148137
2013-12-31 22:44:57,408 DEBUG [AIF]: EBS/FS GL Balances Print Variables - Printing Variables - END
2013-12-31 22:44:57,806 INFO [AIF]: LKM EBS/FS Extract Type - Load Audit AND Full Refresh - START
2013-12-31 22:44:57,817 DEBUG [AIF]:
SELECT p.PROCESS_ID
,br.RULE_NAME
,l.SOURCE_LEDGER_NAME
FROM AIF_GL_LOAD_AUDIT aud
,AIF_PROCESSES p
,AIF_BALANCE_RULES br
,AIF_COA_LEDGERS l
WHERE aud.SOURCE_SYSTEM_ID = 3
AND aud.SOURCE_LEDGER_ID = 1
AND aud.GL_PERIOD_ID = 135
AND aud.BALANCE_TYPE = 'A'
AND p.PROCESS_ID = aud.LAST_LOADID
AND p.STATUS = 'RUNNING'
AND p.PROCESS_ID <> 300
AND br.RULE_ID = p.RULE_ID
AND l.SOURCE_SYSTEM_ID = aud.SOURCE_SYSTEM_ID
AND l.SOURCE_LEDGER_ID = aud.SOURCE_LEDGER_ID
2013-12-31 22:44:57,826 DEBUG [AIF]:
SELECT 'Y' VALID_FLAG
FROM GL_PERIOD_STATUSES
WHERE APPLICATION_ID = 101
AND SET_OF_BOOKS_ID = 1
AND PERIOD_NAME = 'JAN-13'
AND CLOSING_STATUS IN ( 'O','C','P' )
2013-12-31 22:44:57,847 DEBUG [AIF]:
SELECT 'Y' EXISTS_FLAG
FROM GL_TRACK_DELTA_BALANCES
WHERE SET_OF_BOOKS_ID = 1
AND PROGRAM_CODE = 'FEM'
AND PERIOD_NAME = 'JAN-13'
AND ACTUAL_FLAG = 'A'
AND EXTRACT_LEVEL_CODE = 'DTL'
AND CURRENCY_TYPE_CODE = 'B'
AND ENABLED_FLAG = 'Y'
2013-12-31 22:44:57,883 DEBUG [AIF]:
SELECT MAX(DELTA_RUN_ID) MAX_DELTA_RUN_ID
FROM GL_BALANCES_DELTA
WHERE SET_OF_BOOKS_ID = 1
AND PERIOD_NAME = 'JAN-13'
AND ACTUAL_FLAG = 'A'
2013-12-31 22:44:57,898 DEBUG [AIF]:
SELECT brl.EXECUTION_MODE
,( SELECT CASE COUNT(aud.DELTA_RUN_ID) WHEN 0 THEN 'N' ELSE 'Y' END
FROM AIF_GL_LOAD_AUDIT aud
WHERE aud.SOURCE_SYSTEM_ID = 3
AND aud.SOURCE_LEDGER_ID = 1
AND aud.GL_PERIOD_ID = 135
AND aud.BALANCE_TYPE = 'A'
AND aud.LAST_LOADID <> brl.LOADID
AND COALESCE( aud.STATUS, 'SUCCESS' ) = 'SUCCESS'
) GL_LOAD_AUDIT_SUCCESS_FLAG
,( SELECT CASE COUNT(aud.DELTA_RUN_ID) WHEN 0 THEN 'N' ELSE 'Y' END
FROM AIF_GL_LOAD_AUDIT aud
WHERE aud.SOURCE_SYSTEM_ID = 3
AND aud.SOURCE_LEDGER_ID = 1
AND aud.GL_PERIOD_ID = 135
AND aud.BALANCE_TYPE = 'A'
AND aud.LAST_LOADID <> brl.LOADID
AND aud.STATUS = 'RUNNING'
) GL_LOAD_AUDIT_RUNNING_FLAG
FROM AIF_BAL_RULE_LOADS brl
WHERE brl.LOADID = 300
2013-12-31 22:44:57,904 DEBUG [AIF]:
INSERT INTO AIF_GL_LOAD_AUDIT ( LAST_LOADID
,DELTA_RUN_ID
,SOURCE_SYSTEM_ID
,SOURCE_LEDGER_ID
,GL_PERIOD_ID
,BALANCE_TYPE
,GL_EXTRACT_TYPE
,STATUS
) VALUES ( 300
,0
,3
,1
,135
,'A'
,'FULLREFRESH'
,'RUNNING'
2013-12-31 22:44:57,907 DEBUG [AIF]:
DELETE FROM AIF_EBS_GL_BALANCES_STG
WHERE SOURCE_SYSTEM_ID = 3
AND SOURCE_COA_ID = 101
AND SOURCE_LEDGER_ID = 1
AND ACTUAL_FLAG = 'A'
AND PERIOD_NAME = 'JAN-13'
2013-12-31 22:44:59,283 INFO [AIF]: LKM EBS/FS Extract Type - Load Audit AND Full Refresh - END
2013-12-31 22:45:06,507 INFO [AIF]: COMM End Process Detail - Update Process Detail - START
2013-12-31 22:45:06,514 DEBUG [AIF]:
UPDATE AIF_PROCESS_DETAILS
SET STATUS = 'SUCCESS'
,RECORDS_PROCESSED = CASE
WHEN RECORDS_PROCESSED IS NULL THEN 0
ELSE RECORDS_PROCESSED
END + 57408
,EXECUTION_END_TIME = CURRENT_TIMESTAMP
,LAST_UPDATED_BY = CASE
WHEN ('native://DN=cn=911,ou=People,dc=css,dc=hyperion,dc=com?USER' IS NULL) THEN LAST_UPDATED_BY
ELSE 'native://DN=cn=911,ou=People,dc=css,dc=hyperion,dc=com?USER'
END
,LAST_UPDATE_DATE = CURRENT_TIMESTAMP
WHERE PROCESS_ID = 300
AND ENTITY_TYPE = 'PROCESS_BAL_IMP'
AND ENTITY_NAME = 'JAN-13'
2013-12-31 22:45:06,519 INFO [AIF]: COMM End Process Detail - Update Process Detail - END
2013-12-31 22:45:07,106 INFO [AIF]: EBS/FS Load Data - Load TDATASEG_T - START
2013-12-31 22:45:07,112 INFO [AIF]:
Import Data from Source for Period 'January 2013'
2013-12-31 22:45:07,115 DEBUG [AIF]:
SELECT brl.PARTITIONKEY
,brl.CATKEY
,brl.PLAN_TYPE
,CASE brl.PLAN_TYPE
WHEN 'PLAN1' THEN 1
WHEN 'PLAN2' THEN 2
WHEN 'PLAN3' THEN 3
WHEN 'PLAN4' THEN 4
WHEN 'PLAN5' THEN 5
ELSE 0
END PLAN_NUMBER
,brl.EXECUTION_MODE
,br.AMOUNT_TYPE
,br.BALANCE_SELECTION
,br.CURRENCY_CODE
,br.INCL_ZERO_BALANCE_FLAG
,br.BAL_SEG_VALUE_OPTION_CODE
,COALESCE(br.BALANCE_AMOUNT_BS, 'YTD') BALANCE_AMOUNT_BS
,COALESCE(br.BALANCE_AMOUNT_IS, 'PERIODIC') BALANCE_AMOUNT_IS
FROM AIF_BAL_RULE_LOADS brl
,AIF_TARGET_APPLICATIONS app
,AIF_BALANCE_RULES br
WHERE brl.LOADID = 300
AND app.APPLICATION_ID = brl.APPLICATION_ID
AND br.RULE_ID = brl.RULE_ID
2013-12-31 22:45:07,120 DEBUG [AIF]:
SELECT PERIODKEY
FROM TPOVPERIOD
WHERE PERIODDESC = 'January 2013'
2013-12-31 22:45:07,122 INFO [AIF]:
Import Data from Source for Ledger 'JWR Books'
2013-12-31 22:45:07,125 DEBUG [AIF]:
SELECT COA_SEGMENT_NAME
,ACCOUNT_TYPE_FLAG
,BALANCE_TYPE_FLAG
FROM AIF_COA_SEGMENTS
WHERE SOURCE_SYSTEM_ID = 3
AND SOURCE_COA_ID = '101'
AND (
ACCOUNT_TYPE_FLAG = 'Y'
OR BALANCE_TYPE_FLAG = 'Y'
2013-12-31 22:45:07,127 DEBUG [AIF]:
SELECT adim.BALANCE_COLUMN_NAME DIMNAME
,adim.DIMENSION_ID
,dim.TARGET_DIMENSION_CLASS_NAME
,(SELECT COA_SEGMENT_NAME
FROM AIF_COA_SEGMENTS cs
WHERE cs.COA_LINE_ID = tiie.IMPSOURCECOALINEID1
) COA_SEGMENT_NAME1
,(SELECT COA_SEGMENT_NAME
FROM AIF_COA_SEGMENTS cs
WHERE cs.COA_LINE_ID = tiie.IMPSOURCECOALINEID2
) COA_SEGMENT_NAME2
,(SELECT COA_SEGMENT_NAME
FROM AIF_COA_SEGMENTS cs
WHERE cs.COA_LINE_ID = tiie.IMPSOURCECOALINEID3
) COA_SEGMENT_NAME3
,(SELECT COA_SEGMENT_NAME
FROM AIF_COA_SEGMENTS cs
WHERE cs.COA_LINE_ID = tiie.IMPSOURCECOALINEID4
) COA_SEGMENT_NAME4
,(SELECT COA_SEGMENT_NAME
FROM AIF_COA_SEGMENTS cs
WHERE cs.COA_LINE_ID = tiie.IMPSOURCECOALINEID5
) COA_SEGMENT_NAME5
,(SELECT CASE mdd.ORPHAN_OPTION_CODE
WHEN 'CHILD' THEN 'N'
WHEN 'ROOT' THEN 'N'
ELSE 'Y'
END DIMENSION_FILTER_FLAG
FROM AIF_MAP_DIM_DETAILS_V mdd
,AIF_MAPPING_RULES mr
WHERE mr.PARTITIONKEY = tpp.PARTITIONKEY
AND mdd.RULE_ID = mr.RULE_ID
AND mdd.DIMENSION_ID = adim.DIMENSION_ID
) DIMENSION_FILTER_FLAG
,tiie.IMPCONCATCHAR
FROM TPOVPARTITION tpp
INNER JOIN AIF_TARGET_APPL_DIMENSIONS adim
ON adim.APPLICATION_ID = 26
INNER JOIN AIF_DIMENSIONS dim
ON dim.DIMENSION_ID = adim.DIMENSION_ID
LEFT OUTER JOIN TBHVIMPITEMERPI tiie
ON tiie.IMPGROUPKEY = tpp.PARTIMPGROUP
AND tiie.IMPFLDFIELDNAME = adim.BALANCE_COLUMN_NAME
AND tiie.IMPMAPTYPE = 'ERP'
WHERE tpp.PARTITIONKEY = 12
AND adim.BALANCE_COLUMN_NAME IS NOT NULL
ORDER BY adim.BALANCE_COLUMN_NAME
2013-12-31 22:45:07,154 DEBUG [AIF]:
INSERT INTO TDATASEG_T (
LOADID
,PARTITIONKEY
,CATKEY
,RULE_ID
,PERIODKEY
,VALID_FLAG
,CHANGESIGN
,CODE_COMBINATION_ID
,SOURCE_LEDGER_ID
,GL_PERIOD_YEAR
,GL_PERIOD_NUM
,YEAR
,PERIOD
,ATTR1
,ATTR2
,ATTR3
,ATTR4
,ATTR5
,ATTR6
,ATTR7
,ATTR8
,ATTR9
,ATTR10
,ATTR11
,ATTR12
,ATTR13
,ATTR14
,ACCOUNT
,ACCOUNTX
,ENTITY
,ENTITYX
,ICP
,ICPX
,UD1
,UD1X
,UD2
,UD2X
,UD3
,UD3X
,UD4
,UD4X
,DATAVIEW
,DATAKEY
,STAT_BALANCE_FLAG
,CURKEY
,AMOUNT_PTD
,AMOUNT_YTD
,AMOUNT
,AMOUNTX
SELECT pprd.PROCESS_ID LOADID
,12 PARTITIONKEY
,4 CATKEY
,27 RULE_ID
,pprd.PERIODKEY
,'Y' VALID_FLAG
,0 CHANGESIGN
,ccid.CODE_COMBINATION_ID
,bal.SOURCE_LEDGER_ID
,pprd.GL_PERIOD_YEAR
,pprd.GL_PERIOD_NUM
,pprd.YEARTARGET YEAR
,pprd.PERIODTARGET PERIOD
,pprd.PROCESS_ID ATTR1
,bal.SOURCE_SYSTEM_ID ATTR2
,bal.SOURCE_LEDGER_ID ATTR3
,pprd.GL_PERIOD_YEAR ATTR4
,pprd.GL_PERIOD_NAME ATTR5
,bal.ACTUAL_FLAG ATTR6
,bal.BUDGET_VERSION_ID ATTR7
,bal.ENCUMBRANCE_TYPE_ID ATTR8
,ccid.ACCOUNT_TYPE ATTR9
,NULL ATTR10
,NULL ATTR11
,NULL ATTR12
,NULL ATTR13
,NULL ATTR14
,ccid.SEGMENT4 ACCOUNT
,NULL ACCOUNTX
,ccid.SEGMENT1 ENTITY
,NULL ENTITYX
,NULL ICP
,NULL ICPX
,ccid.SEGMENT5 UD1
,NULL UD1X
,ccid.SEGMENT3 UD2
,NULL UD2X
,ccid.SEGMENT6 UD3
,NULL UD3X
,ccid.SEGMENT2 UD4
,NULL UD4X
,( CASE WHEN ccid.ACCOUNT_TYPE IN ('R','E','D','C') THEN 'Periodic' ELSE 'YTD' END ) DATAVIEW
,TDATASEG_DATAKEY_S.NEXTVAL
,'N' STAT_BALANCE_FLAG
,bal.CURRENCY_CODE CURKEY
,( CASE WHEN ccid.ACCOUNT_TYPE IN ('A','E','D') THEN 1 ELSE -1 END ) * ( bal.PERIOD_NET_DR - bal.PERIOD_NET_CR ) AMOUNT_PTD
,( CASE WHEN ccid.ACCOUNT_TYPE IN ('A','E','D') THEN 1 ELSE -1 END ) * ( bal.BEGIN_BALANCE_DR - bal.BEGIN_BALANCE_CR + bal.PERIOD_NET_DR - bal.PERIOD_NET_CR ) AMOUNT_YTD
,( CASE WHEN ccid.ACCOUNT_TYPE IN ('A','E','D') THEN 1 ELSE -1 END ) *
( CASE
WHEN ccid.ACCOUNT_TYPE IN ('R','E','D','C') THEN ( bal.PERIOD_NET_DR - bal.PERIOD_NET_CR )
ELSE ( bal.BEGIN_BALANCE_DR - bal.BEGIN_BALANCE_CR + bal.PERIOD_NET_DR - bal.PERIOD_NET_CR )
END
AMOUNT
,( CASE WHEN ccid.ACCOUNT_TYPE IN ('A','E','D') THEN 1 ELSE -1 END ) *
( CASE
WHEN ccid.ACCOUNT_TYPE IN ('R','E','D','C') THEN ( bal.PERIOD_NET_DR - bal.PERIOD_NET_CR )
ELSE ( bal.BEGIN_BALANCE_DR - bal.BEGIN_BALANCE_CR + bal.PERIOD_NET_DR - bal.PERIOD_NET_CR )
END
AMOUNTX
FROM AIF_EBS_GL_BALANCES_STG_V bal
,AIF_EBS_GL_CCID_STG ccid
,AIF_PROCESS_PERIODS pprd
WHERE bal.SOURCE_SYSTEM_ID = 3
AND bal.SOURCE_LEDGER_ID = 1
AND bal.ACTUAL_FLAG = 'A'
AND ccid.SOURCE_SYSTEM_ID = bal.SOURCE_SYSTEM_ID
AND ccid.SOURCE_COA_ID = bal.SOURCE_COA_ID
AND ccid.CODE_COMBINATION_ID = bal.CODE_COMBINATION_ID
AND pprd.PROCESS_ID = 300
AND pprd.PERIODKEY = '2013-01-01'
AND pprd.SOURCE_LEDGER_ID = bal.SOURCE_LEDGER_ID
AND pprd.GL_PERIOD_NAME = bal.PERIOD_NAME
AND (
bal.BEGIN_BALANCE_DR <> 0
OR bal.BEGIN_BALANCE_CR <> 0
OR bal.PERIOD_NET_DR <> 0
OR bal.PERIOD_NET_CR <> 0
AND bal.CURRENCY_CODE <> 'STAT'
AND bal.TRANSLATED_FLAG IS NULL
2013-12-31 22:45:09,269 INFO [AIF]: Monetary Data Rows Imported from Source: 12590
2013-12-31 22:45:09,293 DEBUG [AIF]:
INSERT INTO AIF_APPL_LOAD_AUDIT (
LOADID
,TARGET_APPLICATION_TYPE
,TARGET_APPLICATION_NAME
,PLAN_TYPE
,SOURCE_LEDGER_ID
,EPM_YEAR
,EPM_PERIOD
,SNAPSHOT_FLAG
,PARTITIONKEY
,CATKEY
,RULE_ID
,PERIODKEY
,EXPORT_TO_TARGET_FLAG
SELECT DISTINCT PROCESS_ID LOADID
,'HFM' TARGET_APPLICATION_TYPE
,'FMTEST2' TARGET_APPLICATION_NAME
,NULL PLAN_TYPE
,SOURCE_LEDGER_ID
,YEARTARGET EPM_YEAR
,PERIODTARGET EPM_PERIOD
,'Y' SNAPSHOT_FLAG
,12 PARTITIONKEY
,4 CATKEY
,27 RULE_ID
,PERIODKEY
,'N' EXPORT_TO_TARGET_FLAG
FROM AIF_PROCESS_PERIODS
WHERE PROCESS_ID = 300
AND PERIODKEY = '2013-01-01'
AND SOURCE_LEDGER_ID = 1
2013-12-31 22:45:09,297 DEBUG [AIF]:
INSERT INTO AIF_APPL_LOAD_PRD_AUDIT (
LOADID
,SOURCE_LEDGER_ID
,GL_PERIOD_ID
,DELTA_RUN_ID
,PARTITIONKEY
,CATKEY
,RULE_ID
,PERIODKEY
SELECT DISTINCT pprd.PROCESS_ID LOADID
,pprd.SOURCE_LEDGER_ID
,pprd.PERIOD_ID GL_PERIOD_ID
,(SELECT MAX(gl.DELTA_RUN_ID)
FROM AIF_GL_LOAD_AUDIT gl
WHERE gl.SOURCE_SYSTEM_ID = 3
AND gl.SOURCE_LEDGER_ID = pprd.SOURCE_LEDGER_ID
AND gl.BALANCE_TYPE = 'A'
AND gl.GL_PERIOD_ID = pprd.PERIOD_ID
) DELTA_RUN_ID
,12 PARTITIONKEY
,4 CATKEY
,27 RULE_ID
,pprd.PERIODKEY
FROM AIF_PROCESS_PERIODS pprd
WHERE pprd.PROCESS_ID = 300
AND pprd.PERIODKEY = '2013-01-01'
AND pprd.SOURCE_LEDGER_ID = 1
2013-12-31 22:45:09,302 INFO [AIF]:
Total Data Rows Imported from Source: 12590
2013-12-31 22:45:09,305 INFO [AIF]: EBS/FS Load Data - Load TDATASEG_T - END
2013-12-31 22:45:09,381 INFO [AIF]: COMM Update Data - Init DataLoadUtil - START
2013-12-31 22:45:09,385 INFO [AIF]: COMM Update Data - Init DataLoadUtil - END
2013-12-31 22:45:09,485 INFO [AIF]: COMM Update Data - Update TDATASEG_T/TDATASEGW - START
2013-12-31 22:45:09,491 DEBUG [AIF]:
DELETE FROM TDATASEG_T
WHERE LOADID = 300
AND PARTITIONKEY = 12
AND CATKEY = 4
AND PERIODKEY = '2013-01-01'
AND AMOUNT = 0
2013-12-31 22:45:09,559 WARN [AIF]:
Warning: Data rows with zero balances exist
2013-12-31 22:45:09,636 INFO [AIF]: Zero Balance Data Rows Deleted: 1879
2013-12-31 22:45:09,654 DEBUG [AIF]:
SELECT DIMNAME
,CASE WHEN RULE_ID IS NULL THEN 'N' ELSE 'Y' END RULE_MAP_FLAG
,SRCKEY
,TARGKEY
,WHERECLAUSETYPE
,WHERECLAUSEVALUE
,CHANGESIGN
,SEQUENCE
,DATAKEY
,MAPPING_TYPE
FROM (
SELECT DISTINCT tdm.DIMNAME
,tdm.RULE_ID
,NULL SRCKEY
,NULL TARGKEY
,tdm.WHERECLAUSETYPE
,tdm.WHERECLAUSEVALUE
,NULL CHANGESIGN
,1 SEQUENCE
,COALESCE(tdm.SYSTEM_GENERATED_FLAG,'N') SYSTEM_GENERATED_FLAG
,NULL DATAKEY
,CASE
WHEN tdm.WHERECLAUSETYPE IS NULL THEN 1
ELSE 3
END MAPPING_TYPE
FROM TDATAMAP_T tdm
WHERE tdm.LOADID = 300
AND tdm.PARTITIONKEY = 12
AND tdm.TDATAMAPTYPE = 'ERP'
AND (tdm.RULE_ID IS NULL OR tdm.RULE_ID = 27)
AND tdm.WHERECLAUSETYPE IS NULL
UNION ALL
SELECT tdm.DIMNAME
,tdm.RULE_ID
,tdm.SRCKEY
,tdm.TARGKEY
,tdm.WHERECLAUSETYPE
,tdm.WHERECLAUSEVALUE
,tdm.CHANGESIGN
,CASE tpp.PARTSEQMAP
WHEN 0 THEN CASE
WHEN (tdm.WHERECLAUSETYPE = 'MULTIDIM') THEN 2
WHEN (tdm.WHERECLAUSETYPE = 'BETWEEN') THEN 3
WHEN (tdm.WHERECLAUSETYPE = 'LIKE') THEN 4
ELSE 0
END
ELSE tdm.SEQUENCE
END SEQUENCE
,COALESCE(tdm.SYSTEM_GENERATED_FLAG,'N') SYSTEM_GENERATED_FLAG
,tdm.DATAKEY
,CASE
WHEN tdm.WHERECLAUSETYPE IS NULL THEN 1
ELSE 3
END MAPPING_TYPE
FROM TDATAMAP_T tdm
INNER JOIN TPOVPARTITION tpp
ON tpp.PARTITIONKEY = tdm.PARTITIONKEY
WHERE tdm.LOADID = 300
AND tdm.PARTITIONKEY = 12
AND tdm.TDATAMAPTYPE = 'ERP'
AND (tdm.RULE_ID IS NULL OR tdm.RULE_ID = 27)
AND tdm.WHERECLAUSETYPE IN ('MULTIDIM','BETWEEN','LIKE')
) q
ORDER BY DIMNAME
,RULE_ID
,SEQUENCE
,SYSTEM_GENERATED_FLAG
,SRCKEY
2013-12-31 22:45:09,672 INFO [AIF]:
Processing Mappings for Column 'ACCOUNT'
2013-12-31 22:45:09,677 DEBUG [AIF]:
UPDATE TDATASEG_T
SET ACCOUNTX = ACCOUNT
,ACCOUNTR = 121
,ACCOUNTF = 3
,AMOUNTX = AMOUNTX * 1
,CHANGESIGN = CASE 1
WHEN -1 THEN CASE CHANGESIGN
WHEN 1 THEN 0
WHEN 0 THEN 1
ELSE CHANGESIGN
END
ELSE CHANGESIGN
END
,VALID_FLAG = CASE '*' WHEN 'IGNORE' THEN 'I' ELSE VALID_FLAG END
WHERE LOADID = 300
AND PARTITIONKEY = 12
AND CATKEY = 4
AND PERIODKEY = '2013-01-01'
AND ACCOUNTX IS NULL
AND (1=1)
2013-12-31 22:45:10,044 INFO [AIF]: Data Rows Updated by Location Mapping 'Like' (LIKE): 10711
2013-12-31 22:45:10,053 INFO [AIF]:
Processing Mappings for Column 'ENTITY'
2013-12-31 22:45:10,057 DEBUG [AIF]:
UPDATE TDATASEG_T
SET ENTITYX = ENTITY
,ENTITYR = 122
,ENTITYF = 3
,AMOUNTX = AMOUNTX * 1
,CHANGESIGN = CASE 1
WHEN -1 THEN CASE CHANGESIGN
WHEN 1 THEN 0
WHEN 0 THEN 1
ELSE CHANGESIGN
END
ELSE CHANGESIGN
END
,VALID_FLAG = CASE '*' WHEN 'IGNORE' THEN 'I' ELSE VALID_FLAG END
WHERE LOADID = 300
AND PARTITIONKEY = 12
AND CATKEY = 4
AND PERIODKEY = '2013-01-01'
AND ENTITYX IS NULL
AND (1=1)
2013-12-31 22:45:10,426 INFO [AIF]: Data Rows Updated by Location Mapping 'Like' (LIKE): 10711
2013-12-31 22:45:10,435 DEBUG [AIF]:
UPDATE TDATASEG_T
SET ENTITYX = ENTITY
,ENTITYR = 132
,ENTITYF = 3
,AMOUNTX = AMOUNTX * 1
,CHANGESIGN = CASE 1
WHEN -1 THEN CASE CHANGESIGN
WHEN 1 THEN 0
WHEN 0 THEN 1
ELSE CHANGESIGN
END
ELSE CHANGESIGN
END
,VALID_FLAG = CASE '*' WHEN 'IGNORE' THEN 'I' ELSE VALID_FLAG END
WHERE LOADID = 300
AND PARTITIONKEY = 12
AND CATKEY = 4
AND PERIODKEY = '2013-01-01'
AND ENTITYX IS NULL
AND (1=1)
2013-12-31 22:45:10,446 INFO [AIF]: Data Rows Updated by Location Mapping 'DEFAULT' (LIKE): 0
2013-12-31 22:45:10,448 INFO [AIF]:
Processing Mappings for Column 'ICP'
2013-12-31 22:45:10,452 DEBUG [AIF]:
UPDATE TDATASEG_T
SET ICPX = '[ICP None]'
,ICPR = 130
,ICPF = 3
,AMOUNTX = AMOUNTX * 1
,CHANGESIGN = CASE 1
WHEN -1 THEN CASE CHANGESIGN
WHEN 1 THEN 0
WHEN 0 THEN 1
ELSE CHANGESIGN
END
ELSE CHANGESIGN
END
,VALID_FLAG = CASE '[ICP None]' WHEN 'IGNORE' THEN 'I' ELSE VALID_FLAG END
WHERE LOADID = 300
AND PARTITIONKEY = 12
AND CATKEY = 4
AND PERIODKEY = '2013-01-01'
AND ICPX IS NULL
AND (1=1)
2013-12-31 22:45:10,784 INFO [AIF]: Data Rows Updated by Location Mapping 'Like' (LIKE): 10711
2013-12-31 22:45:10,798 INFO [AIF]:
Processing Mappings for Column 'UD1'
2013-12-31 22:45:10,802 DEBUG [AIF]:
UPDATE TDATASEG_T
SET UD1X = '[None]'
,UD1R = 124
,UD1F = 3
,AMOUNTX = AMOUNTX * 1
,CHANGESIGN = CASE 1
WHEN -1 THEN CASE CHANGESIGN
WHEN 1 THEN 0
WHEN 0 THEN 1
ELSE CHANGESIGN
END
ELSE CHANGESIGN
END
,VALID_FLAG = CASE '[None]' WHEN 'IGNORE' THEN 'I' ELSE VALID_FLAG END
WHERE LOADID = 300
AND PARTITIONKEY = 12
AND CATKEY = 4
AND PERIODKEY = '2013-01-01'
AND UD1X IS NULL
AND (1=1)
2013-12-31 22:45:11,134 INFO [AIF]: Data Rows Updated by Location Mapping 'Like' (LIKE): 10711
2013-12-31 22:45:11,156 INFO [AIF]:
Processing Mappings for Column 'UD2'
2013-12-31 22:45:11,160 DEBUG [AIF]:
UPDATE TDATASEG_T
SET UD2X = '[None]'
,UD2R = 123
,UD2F = 3
,AMOUNTX = AMOUNTX * 1
,CHANGESIGN = CASE 1
WHEN -1 THEN CASE CHANGESIGN
WHEN 1 THEN 0
WHEN 0 THEN 1
ELSE CHANGESIGN
END
ELSE CHANGESIGN
END
,VALID_FLAG = CASE '[None]' WHEN 'IGNORE' THEN 'I' ELSE VALID_FLAG END
WHERE LOADID = 300
AND PARTITIONKEY = 12
AND CATKEY = 4
AND PERIODKEY = '2013-01-01'
AND UD2X IS NULL
AND (1=1)
2013-12-31 22:45:11,517 INFO [AIF]: Data Rows Updated by Location Mapping 'Like' (LIKE): 10711
2013-12-31 22:45:11,531 INFO [AIF]:
Processing Mappings for Column 'UD3'
2013-12-31 22:45:11,535 DEBUG [AIF]:
UPDATE TDATASEG_T
SET UD3X = '[None]'
,UD3R = 125
,UD3F = 3
,AMOUNTX = AMOUNTX * 1
,CHANGESIGN = CASE 1
WHEN -1 THEN CASE CHANGESIGN
WHEN 1 THEN 0
WHEN 0 THEN 1
ELSE CHANGESIGN
END
ELSE CHANGESIGN
END
,VALID_FLAG = CASE '[None]' WHEN 'IGNORE' THEN 'I' ELSE VALID_FLAG END
WHERE LOADID = 300
AND PARTITIONKEY = 12
AND CATKEY = 4
AND PERIODKEY = '2013-01-01'
AND UD3X IS NULL
AND (1=1)
2013-12-31 22:45:11,870 INFO [AIF]: Data Rows Updated by Location Mapping 'Like' (LIKE): 10711
2013-12-31 22:45:11,883 INFO [AIF]:
Processing Mappings for Column 'UD4'
2013-12-31 22:45:11,887 DEBUG [AIF]:
UPDATE TDATASEG_T
SET UD4X = '[None]'
,UD4R = 128
,UD4F = 3
,AMOUNTX = AMOUNTX * 1
,CHANGESIGN = CASE 1
WHEN -1 THEN CASE CHANGESIGN
WHEN 1 THEN 0
WHEN 0 THEN 1
ELSE CHANGESIGN
END
ELSE CHANGESIGN
END
,VALID_FLAG = CASE '[None]' WHEN 'IGNORE' THEN 'I' ELSE VALID_FLAG END
WHERE LOADID = 300
AND PARTITIONKEY = 12
AND CATKEY = 4
AND PERIODKEY = '2013-01-01'
AND UD4X IS NULL
AND (1=1)
2013-12-31 22:45:12,192 INFO [AIF]: Data Rows Updated by Location Mapping 'Like' (LIKE): 10711
2013-12-31 22:45:12,204 DEBUG [AIF]:
UPDATE TDATASEG_T
SET ATTR14 = DATAKEY
WHERE LOADID = 300
AND PARTITIONKEY = 12
AND CATKEY = 4
AND PERIODKEY = '2013-01-01'
2013-12-31 22:45:12,739 DEBUG [AIF]:
UPDATE TDATASEG_T
SET VALID_FLAG = 'N'
WHERE 1=1
AND (
(1=0)
OR TDATASEG_T.ACCOUNTX IS NULL
OR TDATASEG_T.ENTITYX IS NULL
OR TDATASEG_T.ICPX IS NULL
OR TDATASEG_T.UD1X IS NULL
OR TDATASEG_T.UD2X IS NULL
OR TDATASEG_T.UD3X IS NULL
OR TDATASEG_T.UD4X IS NULL
AND LOADID = 300
AND PARTITIONKEY = 12
AND CATKEY = 4
AND PERIODKEY = '2013-01-01'
AND VALID_FLAG = 'Y'
2013-12-31 22:45:12,754 INFO [AIF]:
Total Data Rows available for Export to Target: 10711
2013-12-31 22:45:12,773 INFO [AIF]: COMM Update Data - Update TDATASEG_T/TDATASEGW - END
2013-12-31 22:45:12,808 INFO [AIF]: COMM End Process Detail - Update Process Detail - START
2013-12-31 22:45:12,823 DEBUG [AIF]:
UPDATE AIF_PROCESS_DETAILS
SET STATUS = 'SUCCESS'
,RECORDS_PROCESSED = CASE
WHEN RECORDS_PROCESSED IS NULL THEN 0
ELSE RECORDS_PROCESSED
END + 10711
,EXECUTION_END_TIME = CURRENT_TIMESTAMP
,LAST_UPDATED_BY = CASE
WHEN ('native://DN=cn=911,ou=People,dc=css,dc=hyperion,dc=com?USER' IS NULL) THEN LAST_UPDATED_BY
ELSE 'native://DN=cn=911,ou=People,dc=css,dc=hyperion,dc=com?USER'
END
,LAST_UPDATE_DATE = CURRENT_TIMESTAMP
WHERE PROCESS_ID = 300
AND ENTITY_TYPE = 'PROCESS_BAL_TRANS'
AND ENTITY_NAME = 'January 2013'
2013-12-31 22:45:12,829 INFO [AIF]: COMM End Process Detail - Update Process Detail - END
2013-12-31 22:45:12,987 INFO [AIF]: COMM Update YTD Amounts - Update YTD Amounts - START
2013-12-31 22:45:12,993 DEBUG [AIF]:
SELECT brl.PARTITIONKEY
,brl.CATKEY
,pprd.YEARTARGET
,pprd.PERIODTARGET
,pprd.SOURCE_LEDGER_ID
FROM AIF_BAL_RULE_LOADS brl
,AIF_PROCESS_PERIODS pprd
WHERE brl.LOADID = 300
AND pprd.PROCESS_ID = brl.LOADID
GROUP BY brl.PARTITIONKEY
,brl.CATKEY
,pprd.YEARTARGET
,pprd.PERIODTARGET
,pprd.SOURCE_LEDGER_ID
HAVING COUNT(*) > 1
2013-12-31 22:45:12,995 INFO [AIF]: COMM Update YTD Amounts - Update YTD Amounts - END
2013-12-31 22:45:13,052 INFO [AIF]: COMM Load TDATAMAPSEG/TDATASEG - Load TDATAMAPSEG/TDATASEG - START
2013-12-31 22:45:13,057 DEBUG [AIF]:
SELECT brl.PARTITIONKEY
,brl.CATKEY
,brl.EXECUTION_MODE
FROM AIF_BAL_RULE_LOADS brl
WHERE brl.LOADID = 300
2013-12-31 22:45:13,059 DEBUG [AIF]:
SELECT PERIODKEY
FROM AIF_APPL_LOAD_AUDIT
WHERE LOADID = 300
AND PARTITIONKEY = 12
AND CATKEY = 4
AND RULE_ID = 27
ORDER BY PERIODKEY
2013-12-31 22:45:13,061 INFO [AIF]:
Processing Data for PeriodKey '2013-01-01'
2013-12-31 22:45:13,065 DEBUG [AIF]:
DELETE FROM TDATAMAPSEG
WHERE PARTITIONKEY = 12
AND CATKEY = 4
AND PERIODKEY = '2013-01-01'
AND (
TDATAMAPTYPE = 'ERP'
OR (
TDATAMAPTYPE = 'MULTIDIM'
AND EXISTS (
SELECT 1
FROM TDATAMAPSEG parent
WHERE parent.PARTITIONKEY = TDATAMAPSEG.PARTITIONKEY
AND parent.DATAKEY = TDATAMAPSEG.TARGKEY
AND parent.CATKEY = TDATAMAPSEG.CATKEY
AND parent.PERIODKEY = TDATAMAPSEG.PERIODKEY
AND parent.TDATAMAPTYPE = 'ERP'
2013-12-31 22:45:13,074 INFO [AIF]: Number of Rows deleted from TDATAMAPSEG: 8
2013-12-31 22:45:13,077 DEBUG [AIF]:
INSERT INTO TDATAMAPSEG (
DATAKEY
,PARTITIONKEY
,CATKEY
,PERIODKEY
,DIMNAME
,SRCKEY
,SRCDESC
,TARGKEY
,WHERECLAUSETYPE
,WHERECLAUSEVALUE
,CHANGESIGN
,SEQUENCE
,VBSCRIPT
,TDATAMAPTYPE
,SYSTEM_GENERATED_FLAG
SELECT DATAKEY
,PARTITIONKEY
,4
,'2013-01-01'
,DIMNAME
,SRCKEY
,SRCDESC
,TARGKEY
,WHERECLAUSETYPE
,WHERECLAUSEVALUE
,CHANGESIGN
,SEQUENCE
,VBSCRIPT
,TDATAMAPTYPE
,SYSTEM_GENERATED_FLAG
FROM TDATAMAP_T
WHERE LOADID = 300
2013-12-31 22:45:13,081 INFO [AIF]: Number of Rows inserted into TDATAMAPSEG: 8
2013-12-31 22:45:13,083 DEBUG [AIF]:
DELETE FROM TDATASEG
WHERE LOADID < 300
AND PARTITIONKEY = 12
AND CATKEY = 4
AND RULE_ID = 27
AND PERIODKEY = '2013-01-01'
2013-12-31 22:45:15,659 INFO [AIF]: Number of Rows deleted from TDATASEG: 10711
2013-12-31 22:45:15,728 DEBUG [AIF]:
INSERT INTO TDATASEG (
DATAKEY
,PARTITIONKEY
,CATKEY
,PERIODKEY
,CURKEY
,DATAVIEW
,CALCACCTTYPE
,CHANGESIGN
,JOURNALID
,AMOUNT
,AMOUNTX
,AMOUNT_PTD
,AMOUNT_YTD
,DESC1
,DESC2
,ACCOUNT
,ACCOUNTX
,ACCOUNTR
,ACCOUNTF
,ENTITY
,ENTITYX
,ENTITYR
,ENTITYF
,ICP
,ICPX
,ICPR
,ICPF
,UD1
,UD1X
,UD1R
,UD1F
,UD2
,UD2X
,UD2R
,UD2F
,UD3
,UD3X
,UD3R
,UD3F
,UD4
,UD4X
,UD4R
,UD4F
,UD5
,UD5X
,UD5R
,UD5F
,UD6
,UD6X
,UD6R
,UD6F
,UD7
,UD7X
,UD7R
,UD7F
,UD8
,UD8X
,UD8R
,UD8F
,UD9
,UD9X
,UD9R
,UD9F
,UD10
,UD10X
,UD10R
,UD10F
,UD11
,UD11X
,UD11R
,UD11F
,UD12
,UD12X
,UD12R
,UD12F
,UD13
,UD13X
,UD13R
,UD13F
,UD14
,UD14X
,UD14R
,UD14F
,UD15
,UD15X
,UD15R
,UD15F
,UD16
,UD16X
,UD16R
,UD16F
,UD17
,UD17X
,UD17R
,UD17F
,UD18
,UD18X
,UD18R
,UD18F
,UD19
,UD19X
,UD19R
,UD19F
,UD20
,UD20X
,UD20R
,UD20F
,ATTR1
,ATTR2
,ATTR3
,ATTR4
,ATTR5
,ATTR6
,ATTR7
,ATTR8
,ATTR9
,ATTR10
,ATTR11
,ATTR12
,ATTR13
,ATTR14
,ARCHIVEID
,HASMEMOITEM
,STATICDATAKEY
,LOADID
,RULE_ID,
CODE_COMBINATION_ID
,STAT_BALANCE_FLAG
,VALID_FLAG
SELECT
DATAKEY
,PARTITIONKEY
,CATKEY
,PERIODKEY
,CURKEY
,DATAVIEW
,CALCACCTTYPE
,CHANGESIGN
,JOURNALID
,AMOUNT
,AMOUNTX
,AMOUNT_PTD
,AMOUNT_YTD
,DESC1
,DESC2
,ACCOUNT
,ACCOUNTX
,ACCOUNTR
,ACCOUNTF
,ENTITY
,ENTITYX
,ENTITYR
,ENTITYF
,ICP
,ICPX
,ICPR
,ICPF
,UD1
,UD1X
,UD1R
,UD1F
,UD2
,UD2X
,UD2R
,UD2F
,UD3
,UD3X
,UD3R
,UD3F
,UD4
,UD4X
,UD4R
,UD4F
,UD5
,UD5X
,UD5R
,UD5F
,UD6
,UD6X
,UD6R
,UD6F
,UD7
,UD7X
,UD7R
,UD7F
,UD8
,UD8X
,UD8R
,UD8F
,UD9
,UD9X
,UD9R
,UD9F
,UD10
,UD10X
,UD10R
,UD10F
,UD11
,UD11X
,UD11R
,UD11F
,UD12
,UD12X
,UD12R
,UD12F
,UD13
,UD13X
,UD13R
,UD13F
,UD14
,UD14X
,UD14R
,UD14F
,UD15
,UD15X
,UD15R
,UD15F
,UD16
,UD16X
,UD16R
,UD16F
,UD17
,UD17X
,UD17R
,UD17F
,UD18
,UD18X
,UD18R
,UD18F
,UD19
,UD19X
,UD19R
,UD19F
,UD20
,UD20X
,UD20R
,UD20F
,ATTR1
,ATTR2
,ATTR3
,ATTR4
,ATTR5
,ATTR6
,ATTR7
,ATTR8
,ATTR9
,ATTR10
,ATTR11
,ATTR12
,ATTR13
,ATTR14
,ARCHIVEID
,HASMEMOITEM
,STATICDATAKEY
,LOADID
,RULE_ID,
CODE_COMBINATION_ID
,STAT_BALANCE_FLAG
,VALID_FLAG
FROM TDATASEG_T
WHERE LOADID = 300
AND PARTITIONKEY = 12
AND CATKEY = 4
AND PERIODKEY = '2013-01-01'
2013-12-31 22:45:16,838 INFO [AIF]: Number of Rows inserted into TDATASEG: 10711
2013-12-31 22:45:16,858 DEBUG [AIF]:
DELETE FROM TDATASEG_T
WHERE LOADID = 300
AND PARTITIONKEY = 12
AND CATKEY = 4
AND PERIODKEY = '2013-01-01'
2013-12-31 22:45:17,123 INFO [AIF]: Number of Rows deleted from TDATASEG_T: 10711
2013-12-31 22:45:17,153 DEBUG [AIF]:
DELETE FROM TDATAMAP_T
WHERE LOADID = 300
2013-12-31 22:45:17,156 INFO [AIF]: Number of Rows deleted from TDATAMAP_T: 8
2013-12-31 22:45:17,161 INFO [AIF]: COMM Load TDATAMAPSEG/TDATASEG - Load TDATAMAPSEG/TDATASEG - END
2013-12-31 22:45:17,993 DEBUG [AIF]:
SELECT CASE app.METADATA_LOAD_METHOD
WHEN 'EPMA' THEN CASE dim.TARGET_DIMENSION_CLASS_NAME
WHEN 'Generic' THEN dim.TARGET_DIMENSION_NAME
ELSE dim.TARGET_DIMENSION_CLASS_NAME
END
ELSE dim.TARGET_DIMENSION_NAME
END TARGET_DIMENSION_NAME
,adim.BALANCE_COLUMN_NAME
FROM AIF_TARGET_APPLICATIONS app
,AIF_TARGET_APPL_DIMENSIONS adim
,AIF_DIMENSIONS dim
WHERE app.APPLICATION_ID = 26
AND adim.APPLICATION_ID = app.APPLICATION_ID
AND dim.DIMENSION_ID = adim.DIMENSION_ID
AND dim.TARGET_DIMENSION_CLASS_NAME IN ('Custom1','Custom2','Custom3','Custom4','Generic')
2013-12-31 22:45:17,997 DEBUG [AIF]:
SELECT SCENARIO "Scenario"
,YEAR "Year"
,PERIOD "Period"
,DATAVIEW "View"
,DATAVALUE "Value"
,ACCOUNT "Account"
,ENTITY "Entity"
,ICP "ICP"
,UD2 "Area"
,UD1 "Tail"
,UD3 "Special"
,UD4 "Facility"
,AMOUNT "DataValue"
FROM AIF_HS_BALANCES
WHERE LOADID = 300
2013-12-31 22:45:18,000 INFO [SimpleAsyncTaskExecutor-9]: ODI Hyperion Financial Management Adapter
2013-12-31 22:45:18,002 INFO [SimpleAsyncTaskExecutor-9]: Load task initialized.
2013-12-31 22:45:18,028 INFO [AIF]: LKM COMM Load Data into HFM - Load Data to HFM - START
2013-12-31 22:45:18,031 DEBUG [AIF]:
INSERT INTO AIF_PROCESS_DETAILS (
PROCESS_ID
,ENTITY_TYPE
,ENTITY_ID
,ENTITY_NAME
,ENTITY_NAME_ORDER
,TARGET_TABLE_NAME
,EXECUTION_START_TIME
,EXECUTION_END_TIME
,RECORDS_PROCESSED
,STATUS
,LAST_UPDATED_BY
,LAST_UPDATE_DATE
) VALUES (
300
,'PROCESS_BAL_EXP_HFM'
,NULL
,'FMTEST2'
,NULL
,NULL
,CURRENT_TIMESTAMP
,NULL
,NULL
,'RUNNING'
,'native://DN=cn=911,ou=People,dc=css,dc=hyperion,dc=com?USER'
,CURRENT_TIMESTAMP
2013-12-31 22:45:18,034 INFO [SimpleAsyncTaskExecutor-9]: Connecting to Financial Management application [FMTEST2] on [10.150.20.40] using user-name [admin].
2013-12-31 22:45:18,155 INFO [SimpleAsyncTaskExecutor-9]: Connected to Financial Management application.
2013-12-31 22:45:18,157 INFO [SimpleAsyncTaskExecutor-9]: HFM Version: 11.1.2.2.300.
2013-12-31 22:45:18,160 INFO [SimpleAsyncTaskExecutor-9]: Options for the Financial Management load task are:
<Options>
<Option name=LOG_FILE_NAME value=C:\Windows\TEMP\/aif_501_300.log/>
<Option name=IMPORT_MODE value=Replace/>
<Option name=CONSOLIDATE_ONLY value=false/>
<Option name=CONSOLIDATE_PARAMETERS value=""/>
<Option name=LOG_ENABLED value=true/>
<Option name=ACCUMULATE_WITHIN_FILE value=false/>
<Option name=DEBUG_ENABLED value=true/>
<Option name=CONSOLIDATE_AFTER_LOAD value=false/>
<Option name=FILE_CONTAINS_SHARE_DATA value=false/>
</Options>
2013-12-31 22:45:18,168 INFO [SimpleAsyncTaskExecutor-9]: Load Options validated.
2013-12-31 22:45:18,176 ERROR [SimpleAsyncTaskExecutor-9]: Error occurred during load process ORA-00904: "DATAVALUE": invalid identifier
com.hyperion.odi.common.ODIHAppException: ORA-00904: "DATAVALUE": invalid identifier
at com.hyperion.odi.hfm.ODIHFMAppWriter.loadData(ODIHFMAppWriter.java:216)
at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method)
at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.java:57)
at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:43)
at java.lang.reflect.Method.invoke(Method.java:606)
at org.python.core.PyReflectedFunction.__call__(PyReflectedFunction.java:175)
at org.python.core.PyObject.__call__(PyObject.java:355)
at org.python.core.PyMethod.__call__(PyMethod.java:215)
at org.python.core.PyMethod.instancemethod___call__(PyMethod.java:221)
at org.python.core.PyMethod.__call__(PyMethod.java:206)
at org.python.core.PyObject.__call__(PyObject.java:397)
at org.python.core.PyObject.__call__(PyObject.java:401)
at org.python.pycode._pyx161.f$0(<string>:98)
at org.python.pycode._pyx161.call_function(<string>)
at org.python.core.PyTableCode.call(PyTableCode.java:165)
at org.python.core.PyCode.call(PyCode.java:18)
at org.python.core.Py.runCode(Py.java:1204)
at org.python.core.Py.exec(Py.java:1248)
at org.python.util.PythonInterpreter.exec(PythonInterpreter.java:172)
at org.apache.bsf.engines.jython.JythonEngine.exec(JythonEngine.java:144)
at com.sunopsis.dwg.codeinterpretor.SnpScriptingInterpretor.execInBSFEngine(SnpScriptingInterpretor.java:322)
at com.sunopsis.dwg.codeinterpretor.SnpScriptingInterpretor.exec(SnpScriptingInterpretor.java:170)
at com.sunopsis.dwg.dbobj.SnpSessTaskSql.scripting(SnpSessTaskSql.java:2472)
at oracle.odi.runtime.agent.execution.cmd.ScriptingExecutor.execute(ScriptingExecutor.java:47)
at oracle.odi.runtime.agent.execution.cmd.ScriptingExecutor.execute(ScriptingExecutor.java:1)
at oracle.odi.runtime.agent.execution.TaskExecutionHandler.handleTask(TaskExecutionHandler.java:50)
at com.sunopsis.dwg.dbobj.SnpSessTaskSql.processTask(SnpSessTaskSql.java:2913)
at com.sunopsis.dwg.dbobj.SnpSessTaskSql.treatTask(SnpSessTaskSql.java:2625)
at com.sunopsis.dwg.dbobj.SnpSessStep.treatAttachedTasks(SnpSessStep.java:558)
at com.sunopsis.dwg.dbobj.SnpSessStep.treatSessStep(SnpSessStep.java:464)
at com.sunopsis.dwg.dbobj.SnpSession.treatSession(SnpSession.java:2093)
at com.sunopsis.dwg.dbobj.SnpSession.treatSession(SnpSession.java:1889)
at oracle.odi.runtime.agent.processor.impl.StartScenRequestProcessor$2.doAction(StartScenRequestProcessor.java:580)
at oracle.odi.core.persistence.dwgobject.DwgObjectTemplate.execute(DwgObjectTemplate.java:216)
at oracle.odi.runtime.agent.processor.impl.StartScenRequestProcessor.doProcessStartScenTask(StartScenRequestProcessor.java:513)
at oracle.odi.runtime.agent.processor.impl.StartScenRequestProcessor$StartScenTask.doExecute(StartScenRequestProcessor.java:1066)
at oracle.odi.runtime.agent.processor.task.AgentTask.execute(AgentTask.java:126)
at oracle.odi.runtime.agent.support.DefaultAgentTaskExecutor$2.run(DefaultAgentTaskExecutor.java:82)
at java.lang.Thread.run(Thread.java:724)
Caused by: java.sql.SQLSyntaxErrorException: ORA-00904: "DATAVALUE": invalid identifier
at oracle.jdbc.driver.T4CTTIoer.processError(T4CTTIoer.java:462)
at oracle.jdbc.driver.T4CTTIoer.processError(T4CTTIoer.java:405)
at oracle.jdbc.driver.T4C8Oall.processError(T4C8Oall.java:931)
at oracle.jdbc.driver.T4CTTIfun.receive(T4CTTIfun.java:481)
at oracle.jdbc.driver.T4CTTIfun.doRPC(T4CTTIfun.java:205)
at oracle.jdbc.driver.T4C8Oall.doOALL(T4C8Oall.java:548)
at oracle.jdbc.driver.T4CStatement.doOall8(T4CStatement.java:202)
at oracle.jdbc.driver.T4CStatement.executeForDescribe(T4CStatement.java:942)
at oracle.jdbc.driver.OracleStatement.executeMaybeDescribe(OracleStatement.java:1283)
at oracle.jdbc.driver.OracleStatement.doExecuteWithTimeout(OracleStatement.java:1441)
at oracle.jdbc.driver.OracleStatement.executeQuery(OracleStatement.java:1690)
at oracle.jdbc.driver.OracleStatementWrapper.executeQuery(OracleStatementWrapper.java:446)
at com.hyperion.odi.hfm.ODIHFMAppWriter.loadData(ODIHFMAppWriter.java:212)
... 38 more
2013-12-31 22:45:18,208 DEBUG [AIF]:
UPDATE AIF_PROCESS_DETAILS
SET STATUS = 'FAILED'
,RECORDS_PROCESSED = CASE
WHEN RECORDS_PROCESSED IS NULL THEN 0
ELSE RECORDS_PROCESSED
END + 0
,EXECUTION_END_TIME = CURRENT_TIMESTAMP
,LAST_UPDATED_BY = CASE
WHEN ('native://DN=cn=911,ou=People,dc=css,dc=hyperion,dc=com?USER' IS NULL) THEN LAST_UPDATED_BY
ELSE 'native://DN=cn=911,ou=People,dc=css,dc=hyperion,dc=com?USER'
END
,LAST_UPDATE_DATE = CURRENT_TIMESTAMP
WHERE PROCESS_ID = 300
AND ENTITY_TYPE = 'PROCESS_BAL_EXP_HFM'
AND ENTITY_NAME = 'FMTEST2'
2013-12-31 22:45:18,210 FATAL [AIF]: Error in LKM CThe issue is that you are mapping "Data Value" to amount in the Target Application import format:
SELECT SCENARIO "Scenario"
,YEAR "Year"
,PERIOD "Period"
,DATAVIEW "View"
,DATAVALUE "Value"
,ACCOUNT "Account"
,ENTITY "Entity"
,ICP "ICP"
,UD2 "Area"
,UD1 "Tail"
,UD3 "Special"
,UD4 "Facility"
,AMOUNT "DataValue"
FROM AIF_HS_BALANCES
WHERE LOADID = 300
You need to map AMOUNT to "AMOUNT" in the HFM Application. Check that the dimension mapping is correct for the class in the target application and that your import format is going to the proper target dimension(Amount). -
I recently bought a new MacBook Pro, and wanted to transfer all the data from my old MacBook Pro, but I get the message saying I need to update time machine on my old one in order to use time machine. However, my old one is too old to update. So I decided to use the cable to transfer, because I heard I can do it that way even though it could take time. But I have no idea what to do...
Can someone help me?A Basic Guide for Migrating to Intel-Macs
The Knowledgebase article Intel-based Mac: Some migrated applications may need to be updated refers to methods of dealing with migrating from PowerPC chips to Intel with the Migration Assistant safely. The authors of this tip have not had a chance to verify this works in all instances, or that it avoids the 10.6.1 and earlier Guest Account bug that caused account information to get deleted upon use of the Migration/Setup Assistant. However, a well backed up source that includes at least two backups of all the data that are not connected to your machine will help you avoid potential issues, should they arise. In event it does not work, follow the steps below.
If you are migrating a PowerPC system (G3, G4, or G5) to an Intel-Mac be careful what you migrate. Keep in mind that some items that may get transferred will not work on Intel machines and may end up causing your computer's operating system to malfunction.
Rosetta supports "software that runs on the PowerPC G3, G4, or G5 processor that are built for Mac OS X". This excludes the items that are not universal binaries or simply will not work in Rosetta:
Classic Environment, and subsequently any Mac OS 9 or earlier applications
Screensavers written for the PowerPC System Preference add-ons
All Unsanity Haxies Browser and other plug-ins
Contextual Menu Items
Applications which specifically require the PowerPC G5 Kernel extensions
Java applications with JNI (PowerPC) libraries
See also What Can Be Translated by Rosetta.
In addition to the above you could also have problems with migrated cache files and/or cache files containing code that is incompatible.
If you migrate a user folder that contains any of these items, you may find that your Intel-Mac is malfunctioning. It would be wise to take care when migrating your systems from a PowerPC platform to an Intel-Mac platform to assure that you do not migrate these incompatible items.
If you have problems with applications not working, then completely uninstall said application and reinstall it from scratch. Take great care with Java applications and Java-based Peer-to-Peer applications. Many Java apps will not work on Intel-Macs as they are currently compiled. As of this time Limewire, Cabos, and Acquisition are available as universal binaries. Do not install browser plug-ins such as Flash or Shockwave from downloaded installers unless they are universal binaries. The version of OS X installed on your Intel-Mac comes with special compatible versions of Flash and Shockwave plug-ins for use with your browser.
The same problem will exist for any hardware drivers such as mouse software unless the drivers have been compiled as universal binaries. For third-party mice the current choices are USB Overdrive or SteerMouse. Contact the developer or manufacturer of your third-party mouse software to find out when a universal binary version will be available.
Also be careful with some backup utilities and third-party disk repair utilities. Disk Warrior, TechTool Pro , SuperDuper , and Drive Genius work properly on Intel-Macs with Leopard. The same caution may apply to the many "maintenance" utilities that have not yet been converted to universal binaries. Leopard Cache Cleaner, Onyx, TinkerTool System, and Cocktail are now compatible with Leopard.
Before migrating or installing software on your Intel-Mac check MacFixit's Rosetta Compatibility Index.
Additional links that will be helpful to new Intel-Mac users:
Intel In Macs
Apple Guide to Universal Applications
MacInTouch List of Compatible Universal Binaries
MacInTouch List of Rosetta Compatible Applications
MacUpdate List of Intel-Compatible Software
Transferring data with Setup Assistant - Migration Assistant FAQ
OS X Lion: How to use Migration Assistant to transfer files from another Mac
Because Migration Assistant isn't the ideal way to migrate from PowerPC to Intel Macs, using Target Disk Mode, copying the critical contents to CD and DVD, an external hard drive, or networking will work better when moving from PowerPC to Intel Macs. The initial section below discusses Target Disk Mode. It is then followed by a section which discusses networking with Macs that lack Firewire.
If both computers support the use of Firewire then you can use the following instructions:
Repair the hard drive and permissions using Disk Utility.
Backup your data. This is vitally important in case you make a mistake or there's some other problem.
Connect a Firewire cable between your old Mac and your new Intel Mac.
Startup your old Mac in Transferring files between two computers using FireWire.
Startup your new Mac for the first time, go through the setup and registration screens, but do NOT migrate data over. Get to your desktop on the new Mac without migrating any new data over.
If you are not able to use a Firewire connection (for example you have a Late 2008 MacBook that only supports USB:)
1. Set up a local home network: Creating a small Ethernet Network.
2. If you have a MacBook Air or Late 2008 MacBook see the following:
MacBook (13-inch, Aluminum, Late 2008) and MacBook Pro (15-inch, Late 2008)- What to do if migration is unsuccessful;
MacBook Air- Migration Tips and Tricks;
MacBook Air- Remote Disc, Migration, or Remote Install Mac OS X and wireless 802.11n networks.
Copy the following items from your old Mac to the new Mac:
In your /Home/ folder: Documents, Movies, Music, Pictures, and Sites folders.
In your /Home/Library/ folder:
/Home/Library/Application Support/AddressBook (copy the whole folder) /Home/Library/Application Support/iCal (copy the whole folder)
Also in /Home/Library/Application Support (copy whatever else you need including folders for any third-party applications)
/Home/Library/Keychains (copy the whole folder) /Home/Library/Mail (copy the whole folder) /Home/Library/Preferences/ (copy the whole folder) /Home /Library/Calendars (copy the whole folder) /Home /Library/iTunes (copy the whole folder) /Home /Library/Safari (copy the whole folder)
If you want cookies:
/Home/Library/Cookies/Cookies.plist /Home/Library/Application Support/WebFoundation/HTTPCookies.plist
For Entourage users:
Entourage is in /Home/Documents/Microsoft User Data Also in /Home/Library/Preferences/Microsoft.
Credit goes to Macjack for this information.
If you need to transfer data for other applications please ask the vendor or ask in the Discussions where specific applications store their data.
5. Once you have transferred what you need restart the new Mac and test to make sure the contents are there for each of the applications.
Written by Kappy with additional contributions from a brody.Revised 5/21/2011 -
How to get data from a pointer to an array using dlportio?
I use DLPORTIO.DLL to access the parallel port on a WinXP. The purpose is to read data coming from an fpga.
The transfer rate is quite high (more than 500kB/s).
DLPORTIO.DLL can buffer data from the parallel port.
I would like to use this fonctionality to speed up the data transfer by ready 16 x 8 bits that have been buffered. I get the pointer to the element from the dll. 8bits means U8 in Labview and, of course, 16 => U16 and 32bits => U32. But what to connect when I want 128bits??? How to use the pointer cominf from the dll and say to Labview it is the pointer to the first element of my 16 element array??
Thanks to all
Dai Tran Duy
Dai
LV 7.1 - WIN XP - RT - FP
Attachments:
dlportio.zip 852 KBLabVIEW does not have a 128 bit numeric so you will need to create a work around of sorts. What I would suggest is creating some wrapper dll functions. These funcitons would take say an array of U8s from LabVIEW, convert them into your 128 bit number and then call your dll with that.
In addition take a look at the manual on exteranl code in LabVIEW, Using External Code in LabVIEW, which discusses how to pass arrays to a dll. In addition there is a shipping example in LabVIEW 7.0 that shows how to pass all sorts of LabVIEW and C data types. The example even includes C code snipits. -
How to fetch the data from databse table and get the required output
Hi,
I have made a project that connects CEP to database table but i m getting some problem in fetching the data from database.
From the following code :
If the where condition is removed then the application runs fine but i am still not able to fetch the data from the table because it is not showing any output.
Can anyone please suggest me that how to write WHERE statement correctly and how i will be able to see the output.
Following is the config.xml for processor:
======================================
<?xml version="1.0" encoding="UTF-8"?>
<wlevs:config xmlns:wlevs="http://www.bea.com/ns/wlevs/config/application"
xmlns:jdbc="http://www.oracle.com/ns/ocep/config/jdbc">
<processor>
<name>JDBC_Processor</name>
<rules>
<query id="q1"><![CDATA[
SELECT STOCK.SYMBOL as symbol, STOCK.EXCHANGE as exchange
FROM ExchangeStream [Now] as datastream, STOCK
WHERE datastream.SYMBOL = datastream.SYMBOL ]]></query>
</rules>
</processor>
<jms-adapter>
<name>JMS_IN_Adapter</name>
<jndi-provider-url>t3://CHDSEZ135400D:7001</jndi-provider-url>
<destination-jndi-name>jms.TestKanikaQueue</destination-jndi-name>
<user>weblogic</user>
<password>welcome1</password>
</jms-adapter>
</wlevs:config>
Following is the assembly file:
<?xml version="1.0" encoding="UTF-8"?>
<beans xmlns="http://www.springframework.org/schema/beans"
xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xmlns:osgi="http://www.springframework.org/schema/osgi"
xmlns:wlevs="http://www.bea.com/ns/wlevs/spring" xmlns:jdbc="http://www.oracle.com/ns/ocep/jdbc"
xmlns:spatial="http://www.oracle.com/ns/ocep/spatial"
xsi:schemaLocation="
http://www.springframework.org/schema/beans
http://www.springframework.org/schema/beans/spring-beans.xsd
http://www.springframework.org/schema/osgi
http://www.springframework.org/schema/osgi/spring-osgi.xsd
http://www.bea.com/ns/wlevs/spring
http://www.bea.com/ns/wlevs/spring/spring-wlevs-v11_1_1_3.xsd
http://www.oracle.com/ns/ocep/jdbc
http://www.oracle.com/ns/ocep/jdbc/ocep-jdbc.xsd
http://www.oracle.com/ns/ocep/spatial
http://www.oracle.com/ns/ocep/spatial/ocep-spatial.xsd">
<wlevs:event-type-repository>
<wlevs:event-type type-name="StockEvent">
<wlevs:properties>
<wlevs:property name="SYMBOL" type="byte[]" length="16" />
<wlevs:property name="EXCHANGE" type="byte[]" length="16" />
</wlevs:properties>
</wlevs:event-type>
<wlevs:event-type type-name="ExchangeEvent">
<wlevs:class>com.bea.wlevs.event.example.JDBC_CEP.ExchangeEvent</wlevs:class>
</wlevs:event-type>
<wlevs:event-type type-name="StockExchangeEvent">
<wlevs:properties>
<wlevs:property name="symbol" type="byte[]" length="16" />
<wlevs:property name="price" type="byte[]" length="16" />
<wlevs:property name="exchange" type="byte[]" length="16" />
</wlevs:properties>
</wlevs:event-type>
</wlevs:event-type-repository>
<bean id="readConverter" class="com.bea.wlevs.adapter.example.JDBC_CEP.Adapter_JDBC" />
<bean id="outputJDBCBean" class="com.bea.wlevs.bean.example.JDBC_CEP.OutputBean_JDBC">
</bean>
<wlevs:adapter id="JMS_IN_Adapter" provider="jms-inbound">
<wlevs:listener ref="ExchangeStream" />
<wlevs:instance-property name="converterBean"
ref="readConverter" />
</wlevs:adapter>
<wlevs:processor id="JDBC_Processor" advertise="true">
<wlevs:listener ref="OutputChannel" />
<wlevs:table-source ref="STOCK" />
</wlevs:processor>
<wlevs:channel id="ExchangeStream" event-type="ExchangeEvent" advertise="true">
<wlevs:listener ref="JDBC_Processor" />
</wlevs:channel>
<wlevs:channel id="OutputChannel" event-type="StockExchangeEvent"
advertise="true">
<wlevs:listener ref="outputJDBCBean" />
</wlevs:channel>
<wlevs:table id="STOCK" event-type="StockEvent"
data-source="StockDs" table-name="STOCK" />
<wlevs:table id="STOCK_EXCHANGE" event-type="StockExchangeEvent"
data-source="StockDs" table-name="STOCK_EXCHANGE" />
</beans>
ExchangeEvent.java:
package com.bea.wlevs.event.example.JDBC_CEP;
public class ExchangeEvent {
public String SYMBOL;
public String symbol;
public String exchange;
public ExchangeEvent() {
public String getSYMBOL() {
return SYMBOL;
public void setSYMBOL(String sYMBOL) {
SYMBOL = sYMBOL;
public String getSymbol() {
return symbol;
public void setSymbol(String symbol) {
this.symbol = symbol;
public String getExchange() {
return exchange;
public void setExchange(String price) {
this.exchange = price;
Adapter Class:
package com.bea.wlevs.adapter.example.JDBC_CEP;
import com.bea.wlevs.adapter.example.JDBC_CEP.MyLogger;
import com.bea.wlevs.adapters.jms.api.InboundMessageConverter;
import java.text.DateFormat;
import java.util.Date;
import com.bea.wlevs.adapters.jms.api.MessageConverterException;
import com.bea.wlevs.event.example.JDBC_CEP.ExchangeEvent;
import javax.jms.JMSException;
import javax.jms.Message;
import javax.jms.TextMessage;
import java.util.ArrayList;
import java.util.List;
import java.util.Random;
public class Adapter_JDBC implements InboundMessageConverter{
@SuppressWarnings("unchecked")
public List convert(Message message) throws MessageConverterException, JMSException {
Random rand = new Random();
int unique_id = rand.nextInt();
DateFormat dateFormat;
dateFormat = DateFormat.getTimeInstance();
dateFormat.format(new Date());
MyLogger.info(unique_id + " CEP Start Time is: " + dateFormat.format(new Date()));
System.out.println("Message from the Queue is :"+ message);
TextMessage textMessage = (TextMessage) message;
String stringMessage = textMessage.getText().toString();
System.out.println("Message after getting converted into String is :"+ stringMessage);
String[] results = stringMessage.split(",\\s*"); // split on commas
ExchangeEvent event1 = new ExchangeEvent();
event1.setSYMBOL(results[0]);
List events = new ArrayList(2);
events.add(event1);
return events;
Output Bean Class :
package com.bea.wlevs.bean.example.JDBC_CEP;
import com.bea.wlevs.ede.api.StreamSink;
import com.bea.wlevs.event.example.JDBC_CEP.ExchangeEvent;
import com.bea.core.datasource.DataSourceService;
public class OutputBean_JDBC implements StreamSink{
public void onInsertEvent(Object event) {
if (event instanceof ExchangeEvent) {
ExchangeEvent cacheEvent = (ExchangeEvent) event;
System.out.println("Symbol is: " + cacheEvent.getSymbol());
System.out.println("Exchange is: " + cacheEvent.getExchange());
System.out.println(DataSourceService.class.getClass());
Kindly let me know if you need further info.Do you have StockDs configured in your server config.xml?
I think the query should look more like this:
SELECT stocks.SYMBOL, stocks.EXCHANGE
FROM STOCK as stocks, ExchangeStream [Now] as datastream WHERE stocks.SYMBOL = datastream.SYMBOL
Thanks
andy -
PROBLEM IN EXPORTING DATA FROM A RELATIONAL TABLE TO ANOTHER RELATIONAL TAB
Hi,
While trying to export data from a source table to a target table, problem occurs with loading the data in the work table(SrcSet0)[As shown in the operator]. The Work Table has been dropped and created successfully, the problem is coming with loading the data( in this work table(SrcSet0)). The error details as mentioned below. Please advise:-
ODI-1227: Task SrcSet0 (Loading) fails on the source ORACLE connection ORACLE_SOURCE.
Caused By: java.sql.SQLException: SQL string is not Query
at oracle.jdbc.driver.OracleStatement.doExecuteWithTimeout(OracleStatement.java:1442)
at oracle.jdbc.driver.OraclePreparedStatement.executeInternal(OraclePreparedStatement.java:3752)
at oracle.jdbc.driver.OraclePreparedStatement.executeQuery(OraclePreparedStatement.java:3806)
at oracle.jdbc.driver.OraclePreparedStatementWrapper.executeQuery(OraclePreparedStatementWrapper.java:1667)
at oracle.odi.query.JDBCTemplate.executeQuery(JDBCTemplate.java:189)
at oracle.odi.runtime.agent.execution.sql.SQLDataProvider.readData(SQLDataProvider.java:89)
at oracle.odi.runtime.agent.execution.sql.SQLDataProvider.readData(SQLDataProvider.java:1)
at oracle.odi.runtime.agent.execution.DataMovementTaskExecutionHandler.handleTask(DataMovementTaskExecutionHandler.java:67)
at com.sunopsis.dwg.dbobj.SnpSessTaskSql.processTask(SnpSessTaskSql.java:2906)
at com.sunopsis.dwg.dbobj.SnpSessTaskSql.treatTask(SnpSessTaskSql.java:2609)
at com.sunopsis.dwg.dbobj.SnpSessStep.treatAttachedTasks(SnpSessStep.java:537)
at com.sunopsis.dwg.dbobj.SnpSessStep.treatSessStep(SnpSessStep.java:453)
at com.sunopsis.dwg.dbobj.SnpSession.treatSession(SnpSession.java:1740)
at oracle.odi.runtime.agent.processor.impl.StartSessRequestProcessor$2.doAction(StartSessRequestProcessor.java:338)
at oracle.odi.core.persistence.dwgobject.DwgObjectTemplate.execute(DwgObjectTemplate.java:214)
at oracle.odi.runtime.agent.processor.impl.StartSessRequestProcessor.doProcessStartSessTask(StartSessRequestProcessor.java:272)
at oracle.odi.runtime.agent.processor.impl.StartSessRequestProcessor.access$0(StartSessRequestProcessor.java:263)
at oracle.odi.runtime.agent.processor.impl.StartSessRequestProcessor$StartSessTask.doExecute(StartSessRequestProcessor.java:822)
at oracle.odi.runtime.agent.processor.task.AgentTask.execute(AgentTask.java:123)
at oracle.odi.runtime.agent.support.DefaultAgentTaskExecutor$2.run(DefaultAgentTaskExecutor.java:82)
at java.lang.Thread.run(Thread.java:662)
Thanks
AnindyaHi actdi,
This is my KM_IKM SQL Incremental Update.xml code:-
and I have find it(for (int i=odiRef.getDataSetMin(); i <= odiRef.getDataSetMax(); i++)) and high lighted it(Bold Text).
So, please advise.
Here is the main part of this code because the code is too long to post.It exceeds maxlength for the msg.
So here it is:
<Object class="com.sunopsis.dwg.dbobj.SnpTxtHeader">
<Field name="Enc" type="java.lang.String">null</Field>
<Field name="EncKey" type="java.lang.String">null</Field>
<Field name="ITxt" type="com.sunopsis.sql.DbInt"><![CDATA[1695003]]></Field>
<Field name="ITxtOrig" type="com.sunopsis.sql.DbInt"><![CDATA[102]]></Field>
<Field name="SqlIndGrp" type="java.lang.String"><![CDATA[2]]></Field>
<Field name="Txt" type="java.lang.String"><![CDATA[insert into <%=odiRef.getTable("L","INT_NAME","A")%>
<%=odiRef.getColList("", "[COL_NAME]", ",\n\t", "", "(((INS or UPD) and !TRG) and REW)")%>,
IND_UPDATE
*<%for (int i=odiRef.getDataSetMin(); i <= odiRef.getDataSetMax(); i++){%>*
<%=odiRef.getDataSet(i, "Operator")%>
select <%=odiRef.getPop("DISTINCT_ROWS")%>
<%=odiRef.getColList(i,"", "[EXPRESSION]", ",\n\t", "", "(((INS or UPD) and !TRG) and REW)")%>,
<% if (odiRef.getDataSet(i, "HAS_JRN").equals("1")) { %>
JRN_FLAG IND_UPDATE
<%} else {%>
'I' IND_UPDATE
<%}%>
from <%=odiRef.getFrom(i)%>
where (1=1)
<%=odiRef.getJoin(i)%>
<%=odiRef.getFilter(i)%>
<%=odiRef.getJrnFilter(i)%>
<%=odiRef.getGrpBy(i)%>
<%=odiRef.getHaving(i)%>
<%}%>
]]></Field>
</Object>
<Object class="com.sunopsis.dwg.dbobj.SnpLineTrt">
<Field name="AlwaysExe" type="java.lang.String"><![CDATA[0]]></Field> -
How to save the dynamic data from a pressure sensor
Hello Everyone,
We have a FPGA board NI cRIO-9073, a temperature module NI 9217 and a pressure module NI 9203. Right now we have problem with saving the data from pressure sensor. I succeed in getting and saving the data from the temperature sensor. Then I just simply modify the FPGA VI and host VI of the temperature function block which are shown in the attachment files.But I get an error saying I cannot connect two different data types.
Could anyone here give me a help on this?
BTW: we are using a 2 wired pressure sensor with 4~20mA. The brown one is +Vcc and the white one is GND.I connect the white one with the COM of NI 9203 and the brown one is connected to AI7. DidI make a right connection?
Thx for any help from anyone!
Attachments:
pre_tem.JPG 36 KB
pre.jpg 35 KBHi, I get this error message:
Write to textfile: function contains an unrelated or improper connection.You have combined two different types of connections among each other.
At least one entrance of the function required for their operation, is open or not properly connected, the connection scheme is illustrated in the context help.
They have combined two different types of connections with each other. This connection is not possible because the data types (such as "numeric", "String", "Arrary" or "clusters do not match"). Open to see the contextual help at what must have a data type for the connection. The type of data source (fixed) costs. The type of data is dynamic data.
Maybe you are looking for
-
Files open using Notepad o always in minimized size
All of a sudden, when I open a file using note pad, it always open in minimized size, I have to give an extra click to maximaze it. I searched on line, and tried something like to setup in Notepad property window, in run field , set it to normal. Or
-
!!! Jsp compilation error in deploying : in migrating from WLS 8.1 to 9.2
Hi, We are trying to migrate a .war file from WLS 8.1 to WLS 9.2. After other changes are done, while deploying the .war file in in WLS 9.2 we are getting errors for a jsp file: 1> Syntax error near 'import' ^-------------------^ 2> at Line 6 ;The qu
-
IMovies 08 use with Sony Handycam DCR-DVD 109
Does anyone know for 100% tried and tested, if you can just plug a Sony Handycam DCR-DVD-109 directly into an iMac using imovies 08 and import home movies directly so they can be edited. Many thanks
-
Powerview modifying a calculated measure in SSAS cube
We are running SQL Server 2012 and Sharepoint 2013 we are having problems with Powerview modifying a calculated measure in the underlying multidimensional cube. We have a powerview report with multiple pages that allows a user to utilize a global fil
-
Site Definition losing FTP User ID and Password
My configuration: iMac 2.4 GHz Intel C2D 10.6.1 Snow Leopard DW v10 (Build 4117) Not sure if my issue is related to the one described in this thread. I recently performed a clean install of Snow Leopard and DW. Afterwards I imported my site definitio