Trouble with output to tape in PrPro 14 with AJA Kona. Win7pro64. Output to HDCam (HDW-F500), prerolls and parks until reference is cycled. Won't do an audio only insert edit.

I have downloaded and installed the latest drivers from AJA, but am still having trouble outputting to tape.

Well, this is admittedly making my head spin, but would it be possible, with that level of frame rate mismatch, for recording to even take place? The deck was definitely set for 23.98 and PsF (that's what both the indicators said).
At a point of boiling frustration, I performed an Assemble Edit (instead of the typical Insert, after I blacked a tape). When doing that - just for the heck of it - the recording went on for 83 minutes, it gave me a Lost Lock with 1 minute left in our end credits. I then rewound the tape for about 60 minutes and played. Got a Lost Lock in 20 seconds with a picture dropout.
Since you're familiar with the deck, does this seem at all plausible? Does this feed your theory about a frame rate/communication mismatch?

Similar Messages

Outputting to tape via MacBook with Lacie Drive?

So this may have been covered but I can't find it so here it goes: The MacBook has only 1 Firewire port. I'm looking for suggestions for outputting to tape when also using a Lacie Drive which occupies the port. Hooking the Lacie up via the USB won't be fast enough right? So this means figuring out an alternate way to lay off to tape from FCPHD. Does this mean rendering the sequence out as .mov file? If so, which codec is going to give it as close to the same resolution as if I was laying off directly from the FCPHD Print to video?

It depends on the camera npeovideo is using: Canon cameras seem not to like to be daisy chained with LaCie drives... even though mine (Canon MVX4i = Optura 600) works perfectly. But from the other posts in this forum I'm probably an exception.
So I suggest npeovideo first tries daisy chaining. If it works, OK.
If it doesn't work, the only solution I can think of is to copy the project media from the LaCie into the internal hard drive (and reconnect it), disconnect the LaCie drive and print to video to the camcorder, directly connected to the Macbook firewire port. Using USB connection for the external drive might lead to dropped frames and loss of quality.
As an alternative, in order to reduce the need for internal disk space, and in case npeovideo edited a short movie out of an originally long raw movie, he could: a. Export > Quicktime Movie, self contained, (not: Using QuickTime Conversion) to the internal disk drive, b. create a new FCE project where you import that movie into a new sequence, and c. without any further editing, just print to video that sequence (after disconnecting the LaCie drive as above).
I hope some of this may solve the problem.
Piero

I have problem with my wifi in 4 S, i cant connect to any wifi itried resetting network setting and reset all setting but the result was the same, its only keeps searching for wifi and cant find any, itried to use OTHER but also didnt work.please help me

i have problem with my wifi in 4 S, i cant connect to any wifi itried resetting network setting and reset all setting but the result was the same, its only keeps searching for wifi and cant find any, itried to use OTHER but also didnt work.please help me???

If Join was on then your home wi-fi must be set to Non-Broadcast. If you did not set this up (maybe your provider did) then you will need to find the Network Name they used, and any password they used. The SSID is Security Set ID and to see more try http://en.wikipedia.org/wiki/SSID . Basically it is the name used to identify your router/network. A lot of times the installer will leave it set as LinkSys, or Broadcom or whatever the manufacturer set it as for default. Your best bet is to get whoever installed it to walk you through how they set it up, giving you id's and passwords so you can get in. HOWEVER, if you are not comfortable with this (if you set security wrong, etc.) you would be well ahead of the game to hire a local computer tech (networking) to get this working for you. You can also contact the vendor of your router and get help (if it is still in warranty), or at least get copies of the manuals as pdf files. Sorry I can't give you more help, I hope this gives you an idea where to go from here to find more.

CUDA acceleration and Aja Kona LHi output on Mac

Hi, I hope some of you can answer my question. I'm getting mixed information right now. So can I have CUDA acceleration turned on when outputtin picture through Aja Kona Lhi? Or is it so that CUDA and I/O devices such as Blackmagic/Aja cards don't work together? Best Tapio

Those Mac Pro's should be fine with the Nvidia cards. The new ones are not approved with them and are not supported according to Apple. It took Blackmagic several months to get the driver worked out to allow the MPE in a Blackmagic project so I am not suprised if AJA is still working on it. I will say that we have not tried the MPE with the Blackmagic on the Mac side. We have many times on the PC side and it works fine as does Matrox.
Eric
ADK

Best way to play Audio only on a DVD with video?

I have a Meditavie DVD i am making with both video and Audio combined....and i want to make some tracks that are just Audio only
for close eye Meditations. ( i dont want to have to add a CD with the DVD for just Audio)
I made one years ago and just used black as the video output track.
Is there a way to save space and just have the audio track play?
And if so how might i do it and also link to the DVD menu?
Thanks for any help!
Soshman

Below is what I wrong before I tested the obvious. Just "import as timeline" the audio only (make sure there is no m2v with the same name); Encore happily builds a disk with black. Mediinfo shows the video stream, but it appears to be at a very low datarate. So, give it a try. I did not burn a disk; just build to a folder and used a software player.
Other options: Encore slideshows have odd problems, I'd play with making a single slide (just black, right?) slideshow, maybe set to manual advance with no advance - or a very long duration to match the audio length.
If an m2v works better for whatever reason, Encore has a minimum bitrate, I think around 2.x or 1.x. So I would try exporting from Premiere,10 seconds of black video using CBR 1.0, 2.0 and 3.0 and see if it matters.

Audio Playback Issues in Premiere Pro 8.1.0 with AJA Kona 3

Hi,
I'm supporting a couple of edits running the latest version of Premiere Pro. The editors are experiencing some strange stuttering/glitching audio playback via the installed AJA Kona 3 cards, manifested as follows:
When scrubbing using keyboard arrow keys for any prolonged period of time, audio either begins to stutter or fails to playback (despite there being activity on the audio monitors within the software)
When playing audio with unrendered effects (nothing too challenging, unrendered titles etc.), the audio will occasionally not play at all or will begin to stutter also.
Specs are as follows:
HP z800 running Windows 7 64-bit
2 x Intel Xeon X5650 CPUs
32GB RAM
512GB Samsung SSD
nVidia Quadro 4000 (latest drivers installed)
AJA Kona 3 (latest drivers installed)
Wacom Intuos 4 tablet (latest drivers installed)
Storage is a SMB share connected via a dedicated 1Gb/s ethernet link (Intel PRO 1000 card) and media is largely DVCPRO HD 100 wrapped as OP1a MXF, with corresponding sequence settings.
I've played with various RAM and Playback settings (including setting the AJA video playback buffer to 'minimum' as suggested on another thread regarding audio playback), but the problems persist. Is there anything else I can try, or more information I can provide?

Since it worked with CS5.5, check with Blackmagic to see if they have updates for CS6
I know from other discussions that an nVidia driver update was needed for at least some people upgrading to CS6

I have a problem with my macbook,if I don't have my earphone plugged, I can't listen anything,and start shine a red light. what should I do?

I have a problem with my macbook,if I don't have my earphone plugged, I can't listen anything,and start shine a red light .what should I do?

try inserting and removing the headphones in and out of the audio jack. The toggle switch is stuck and your mac thinks the headphones are still plugged in.

Having trouble outputing to tape via firewire

I'm trying to output to tape via firewire. However I'm only recording audio and not video. Device control preset is Firewire NTSC. Video playback preset is Apple Firewire NTSC (720 x 480)
Any suggestion?

Make sure the your Video out is set to ALL FRAMES along with the firewire.
I've no experience with the deck so can't offer any help with it's settings.
As a trouble shooting measure, does the video show up if you use another DV/Analog converter (then on to a TV monitor to visually verify)?
x

Bridge CS4 won't output to pdf multiple images with same filename

Hiya...my googling efforts have thus far failed!
I've got CS4, and in Bridge, I created a New Smart Collection to find all filenames in a folder containing "." or ".jpg" - which in turn searched through all the subfolders like what you used to be able to do in Photoshop CS3. Very simple stuff, but all the images are jpg's, but in multiple folders (I don't want to move them out of the folders, as the files came from an external source, and there are heaps of folders, and I don't want to pdf each subfolder seperately as it will take forever).
The problem is that some of the files have the same filenames (again I'd prefer not to rename, as it happens a lot on this project, and they are all over the place). So whilst Bridge will show the thumbnail images correctly in the content tabbed screen in my New Smart Collection, but once I've done the Output to PDF thing, for example, instead of showing both different images it has pdf only the first image but repeated it twice. And this happens multiple times throughout the pdf, the more times the same filename is used, the more times the first image gets repeated.
I know that it is messy to have multiple similar filenames, but why can't bridge just place the image anyway? It allocated a space for it on the pdf and does show it in bridge, it just doesn't seem to survive the transfer to pdf well.
The only other thing that I have done is use the below link (which was posted on another adobe forum thread) to create a custom pdf output template (nothing too fancy, just number of rows / columns, size, font etc). But I've tried using the standard bridge templates and it does the same thing.
http://www.proficiografik.com/2009/08/03/save-custom-pdf-output-template-in-adobe-bridge-c s4.html
Any help would be appreciated...even if to tell me that I am being unreasonable!
UPDATE 16/11/09
Just to let you know that I seem to have resolved the bug inadvertently with one of the Adobe updates. The below is the link for the AdobeOutputModule-2.1-mul-AdobeUpdate.zip which was released on 2/19/2009 - which allows for headers & footers to be placed in the Ouput pdf. I finally installed it today, and everything seems to be working fine now (i.e. I can pdf multiple images with the same filenames and the pdf will actually show each different image rather than repeating only 1 of the images).
Must have been a fix installed in the contact sheet templates that get installed with the update - not sure why the original version was corrupted, but I've left that with the Adobe guys (I submitted a bug report - and they were able to replicate the problem but hadn't fixed it as yet).
http://www.adobe.com/support/downloads/detail.jsp?ftpID=4228
Message was edited by: djtun71 (16/11/09)

When I click import from disc I am asked to choose a disc and then I get this message:
The following photos will not be imported because they are already present in the catalog. To see these photos in the catalog select 'Show in Library' (the import will be canceled).
This is followed by a long list of images. If I click 'Show in Library' I can see all the images with the same filename. And then they start to automatically write over those images with images from the disc. However they keep the same metadata and keywords from the previous images. If I click on Import and deselect the "don't reimport suspected duplicates" box, it imports only the images that don't share filenames and none of the images that do.
Is there a way of setting the "Don't reimport suspected duplicates" box in preferences?

Problem with backups on Tape

Could you help me ,I have a problem with backups on tape drive .The error which Windows throws is "BackupTapeFile::UnloadTape: PrepareTape(UNLOCK) failure on backup device '\\.\tape0'. Operating system error 21(failed to retrieve text for this error. Reason: 15105)."
Does anyone of you have the same problem.Thank you!

You cannot perform a regular restore/recovery (up to the latest possible point in time), because at this time dropped tablespace is not known to the controlfiles/recocery catalog and therefore not known to RMAN,too. You have to 2 possibilities:
1. Restore the entire database and recover back in time to before the tablespace is dropped.
This will cause ALL data within the database to go back in time, not just this tablespace.
2. Clone the target database to a new location, perform point in time recovery in order to export
the data of the tablespace for import into the original database. This causes the data of this
tablespace to be brought back into the production database, not effecting existing (current) data
in any other area of the database.
As you can see recovering from a dropped tablespace needs some additional efforts. By the way you also cannot use RMAN's TSPITR functionality.
Werner

I have a Canon Vixia HV30 and would like to know if I can transfer video from it to a new MacBook Pro? The camcorder has a HDV/DV output. Is that compatible with firewire?

I have a Canon Vixia HV30 and would like to know if I can transfer video from it to a new MacBook Pro? The camcorder has a HDV/DV output. Is that compatible with firewire?

Hi Codye24
I don't know if you saw this thread
Connecting a Canon HV30 camcorder vai a thunderbolt port to a new imac
Hope that this helps
Kevin

Having trouble setting up a linksys WRT54GS router with v...

Having trouble setting up a linksys WRT54GS router with verizon DSL using a westell 6100F modem. the modem works fine by its self but the router will not connect to the internet when installed like the cd tells you to.
online help and phone help has been less than helpful, anyone have any Ideas?

Ok I found " Installing the liksys wireless router with a westell 6100 modem" in the verizon troubleshooting guides. printed the instructions so I would'nt forget. step 1 open your web browser and enter http://192.168.1.1 in the address field. PROBLEM it comes up with a login screen that I don't know how to sign into. tried the obvious stuff. cannot get past the login screen. I knew this sounded to easy to be true. anyone have any ideas?

Safari keeps crashing every time I try to open a link from a different application, i.e. Mail. The trouble report says that some problem occurs with libcooliris.dylib plug-in. Can any one help?

Safari keeps crashing every time I try to open a link from a different application, i.e. Mail. The trouble report says that some problem occurs with libcooliris.dylib plug-in. Can any one help?
Thanks!

Dear Linc,
Thank you for the advice, John Blanchard1 and Linc Davis
As suggested in your reference thread I removed "/Library/Printers/hp/PDEs/hpPostScriptPDE.plugin" and the problem has been resolved.
I am guessing the the plug-in for the hp printers got corrupted and effected every thing, or became unsuitable when I installed an Apple update. I would be most grateful if you can confirm how the problem was coursed so I can understand and learn from this experiance.
Ash

How to download the output of a report along with column header

Hi,
Could someone please tell me on how to download the output of a report along with column header to .txt format. A download option needs to be given to the user using physical and logical file names .The report basically contains header details and item details and requirement is to download the same format into an .txt format.

Hello,
Try this FM:
Data: being of itab occurs 0,
matnr like mara-matnr,
maktx like makt-maktx,
end of itab.
data:begin of fld_tab occurs 0,
fld_name(20),
end of fld_tab.
fld_tab = 'Material'.
append fld_tab.
fld_tab = 'Material Desc'.
append fld_tab.
CALL FUNCTION 'WS_DOWNLOAD'
   EXPORTING
        BIN_FILESIZE            = ' '
        CODEPAGE                = ' '
         FILENAME                = 'C:\1.txt '
         FILETYPE                = 'DAT'
        MODE                    = ' '
        WK1_N_FORMAT            = ' '
        WK1_N_SIZE              = ' '
        WK1_T_FORMAT            = ' '
        WK1_T_SIZE              = ' '
        COL_SELECT              = ' '
        COL_SELECTMASK          = ' '
        NO_AUTH_CHECK           = ' '
   IMPORTING
        FILELENGTH              =
     TABLES
          DATA_TAB                = itab
          FIELDNAMES              = fld_tab
   EXCEPTIONS
        FILE_OPEN_ERROR         = 1
        FILE_WRITE_ERROR        = 2
        INVALID_FILESIZE        = 3
        INVALID_TYPE            = 4
        NO_BATCH                = 5
        UNKNOWN_ERROR           = 6
        INVALID_TABLE_WIDTH     = 7
        GUI_REFUSE_FILETRANSFER = 8
        CUSTOMER_ERROR          = 9
        OTHERS                  = 10
IF SY-SUBRC <> 0.
MESSAGE ID SY-MSGID TYPE SY-MSGTY NUMBER SY-MSGNO
        WITH SY-MSGV1 SY-MSGV2 SY-MSGV3 SY-MSGV4.
ENDIF.
Regards,
Naimesh

Tearing on VGA output, LVDS OK on 950GMA with xf86-video-intel-2.6.10

I'm crossposting this message i sent on intel-graphics ml and xorg bugzilla, because maybe some of you can point me to a solution.
i own an asus eeepc1005ha, it uses intel gma 950.
Playing a video on the internal LVDS panel is very pleasing and tear
free, but as soon as i connect the vga output, i can notice tearing or
flickering on the picture.
I tried all possible configurations:
-Booting with the lid open (tty on LVDS) and then switching to xorg
with a VGA only output. (VGA tears)
-Booting with the lid closed (tty on VGA) and using xorg on VGA. (VGA tears)
-VGA+LVDS in clone mode (VGA and LVDS tears)
-VGA+LVDS in multihead mode (expanded desktop) (VGA and LVDS tears)
Using xv adaptor via mplayer results in a different tear effect, seems
more like a flickering, while the GL output definitely tears.
I couldn't try overlay adaptor because i don't have a 2.6.33 kernel yet
(believe it or not, i've seen overlay tearing too with an old intel
driver in the past, i think 2.7.1, in a cloned mode if lvds was at
60hz, while vga was at 70hz)
I'm using xf86-video-intel 2.10.0 and kernel 2.6.32.9
I used the framerate test videos available here:
http://spng.se/frame-rate-test/
Thanks for reading.
Last edited by kokoko3k (2010-03-07 08:23:48)

You're right, here's the references:
http://lists.freedesktop.org/archives/i … 06092.html
http://bugs.freedesktop.org/show_bug.cgi?id=26925
About your command, i'll try, but what it does is just picking the first port from first adaptor, right?
By now (xf86-video-intel 2.10.0 and kernel 2.6.32.9), we just have a single adaptor, the textured one;
why the first port should make a difference?
Maybe with your setup the overlay adaptor was picked, and in 99% of the cases that would certanly help.
As a side note, newer mplayer versions comes with an useful option: -vo xv:adaptor=#
What i think is that vblank interrupts generation is (and was) messed up in the drivers code.
see:
(believe it or not, i've seen overlay tearing too with an old intel
driver in the past, i think 2.7.1, in a cloned mode if lvds was at
60hz, while vga was at 70hz)

Trouble with output to tape in PrPro 14 with AJA Kona. Win7pro64. Output to HDCam (HDW-F500), prerolls and parks until reference is cycled. Won't do an audio only insert edit.

Similar Messages

Maybe you are looking for