"Two E-Series"... Example vi's have -10486 error for 32 channels!
Using 2 PCI-6024E cards; all 32 channels!!(Win98, 256Meg RAM, new Pentium). This error claims the buffer is not large enough but if the AI Read.vi start point cluster input is changed to "trigger point" (in case of dig. trigger), then this intermittent error goes away. Have also found errors in data timing...
I believe that the error you are seeing is -10846 which says the application in unable to retrieve data from the buffer fast enough. It suggests to either increase the buffer size, increase the number of scans to read, decrease the acquisition rate, or reduce the number of tasks.
What is happening is that you are trying to read from the first data point in the buffer. But that data point is being overwritten when the buffer overflows so LabVIEW gets confused on where to find it.
The reason why the error no longer appears when setting the read position to "relative to trigger point" is because in this case the application starts to read from the end of the buffer or the last data point that was acquired. This data point will almost never get overwritten and there
fore there is no confusion.
Similar Messages
-
Apple associated publishers for Ibook Store (example: Lulu, SmashWords) have not support for Ibook Author native format (.ibook) how ebook source. Only Word archives are supported.
Obtain TAX ID for non USA resident is impossible without pay to much money.
How to publish in Ibookstore a non USA resident author, in new Ibook Author format?Regardless of what format you want to use, you can't publish in the iBookstore without meeting Apple's requirements, so if you find those too difficult, you need to go elsewhere.
-
Why can I only get the first 7 episodes of the killing series 2 ... I cannot find any more to download on iTunes ???
Welcome to the Apple Community.
Are you sure they are available yet. You may have bought a season pass, which means they will download once they are available. -
Have 2 errors for quicktime when installing itunes
what does these errors mean and how to resolved them...
1.)Error writing to file: C:\ProgramFiles\QuickTime\PropertyPanels\PanelHelperBase.qpa
Verify that you have access to that directory
2.)Error writing to file: C:\ProgramFiles\QuickTime\PropertyPanels\PropertyPanels.plist
Verify that you have access to that directory
installation aborted...
then again..there is problem with the windows installer....That one's consistent with disk/file damage. The first thing I'd try with that is running a disk check (chkdsk) over your C drive.
XP instructions in the following document: How to perform disk error checking in Windows XP
Vista instructions in the following document: Check your hard disk for errors
Windows 7 instructions in the following document: How to use CHKDSK (Check Disk)
Select both Automatically fix file system errors and Scan for and attempt recovery of bad sectors, or use chkdsk /r (depending on which way you decide to go about doing this). You'll almost certainly have to schedule the chkdsk to run on startup. The scan should take quite a while ... if it quits after a few minutes or seconds, something's interfering with the scan.
Does the chkdsk find/repair any damage? If so, can you get an install to go through properly afterwards? -
I have the iphone 4s. Ive tried to update my phone & its stuck on the connect to itunes screen. Ive tried to even restore my phone then update & i still have a error for both of them. I have the latest version of itunes & went through all the other steps. Its still not working & stuck on the connect to itunes & im growing extremly fusterated.
There are multiple reasons that lead to issue. You should read the troubleshooting guide to get the right solution to solve the issue: iPhone, iPad, or iPod touch not recognized in iTunes for Windows - Apple Support
-
Why do assets shift to the left when I delete something? For example if I have a whole series of te
Why do assets shift to the left when I delete something? For example if I have a whole series of text inserts in my movie and I delete one... assets to the left of the deleted text will shift. And the snap is NOT checked. It would be helpful if assets would stay in place and not shift to the left ... groan.
And thanks for the help previously given on another issue. I can't seem to find the origional post but did want to thank Steve for his help. Most appreciated.
BevHold the Shift key down while you press delete.
Cheers,
Neale
Insanity is hereditary, you get it from your children
If this post or another user's post resolves the original issue, please mark the posts as correct and/or helpful accordingly. This helps other users with similar trouble get answers to their questions quicker. Thanks. -
Q: Re: Q: Acquiring data using two E series devices connected by RTSI and streaming data to disk
<< (My first posting)
I use two E series PCI Cards, connected by RTSI. I'd like to stream the data
from both cards to a binary file and to add a header to it.
I also need to somehow read (plot) the stored data, this with another VI.
The whole should be then integrated into an existing program, that used just
one acquisition card.
Till now I have tried to combine "Two E-series Shared ScanClk.vi" and "High
Speed Data Logger.vi" into another VI, and I have tried to read the stored
data with the "High Speed Data Reader.vi". The problem is that I fight with
one error after another, what prevents me from going further.
I use LabView 6.1, under Windows 2K.
Has somebody by chance already done something similar and would agree to
share with me their experience? TIA for any suggestion.
Regards,
Victor Manta
>>
"Ben" wrote in message
news:[email protected]...
> Hi Victor,
>
> I have done a lot of similar work.
>
> Exactly what did you try and what specific errors did you encounter?
>
> What you are trying is do-able provided the hardware you have suuports
> it.
>
> Please post (both here and to the DAQ group)
> the details of the hardware you are using,
> versions of software being used,
> Examples that you are using,
> error codes that occured,
> posibly post example code showing the problem.
>
> Ben
Hi Ben,
I use two PCI-MIO-16E-1 cards, connected by RTSI. I'd like to stream the
data from both cards in real time to a binary file, after having added a
header to it.
For tests, on the channel 0 of each card is applied the same square wave,
100 Hz.
Yes, the hardware support RTSI. I use LabView 6.1.
Till now I have:
1. Combined the "Two E-series Shared ScanClk.vi" and the "High
Speed Data Logger.vi" into a DAQ VI. To do this, I have "doubled" and
adapted the "High Speed Data Logger.vi". For testing purposes the data are
stored in two files, always the same ones (the old ones being overwritten
after each acquisition).
2. "Doubled" and adapted "High Speed Data Reader.vi" into another VI, for
reading from both files, mentioned earlier.
What already works:
- The headers for both files are correctly stored (VI point 1.)
- The acquired data from the first card (device 1) are correctly stored (VI
point 1.)
- The VI (point 2.) that reads both files and displays the results works
What doesn't work:
- The acquired data from the second card aren't stored at all (VI point 1.)
- An error message says: "Error -10608 occurred at AI Buffer Read. Possible
reason: NI-DAQ LV: No transfer is in progress for the specified resource."
I think that I understand this message, but I don't know how to continue.
The DAQ VI can be downloaded from (please click the link, then the link on
that page; about 100K, zipped):
http://www.swissheartnet.unibe.ch/labview.htm
Thanks a lot in advance.
Regards,
Victor Manta
PS. I don't know which DAQ group you mean."Filipe A." wrote in message
news:[email protected]...
> Victor;
>
> You can definitely accomplish that task with the DAQ boards you have
> and Labview.
>
> It would be good if you could be more specific as far as what type of
> errors you are seeing and how you are integrating both VIs.
>
> Regards
> Filipe A.
> Applications Engineer
> National Instruments
Maybe Mr. Filipe A. could help me? Please see below, and TIA.
Regards,
Victor Manta
"Victor Manta" wrote in message
news:[email protected]...
> << (My first posting)
> I use two E series PCI Cards, connected by RTSI. I'd like to stream the
data
> from both cards to a binary file and to add a header to it.
>
> I also need to somehow read (plot) the stored data, this with another VI.
>
> The whole should be then integrated into an existing program, that used
just
> one acquisition card.
>
> Till now I have tried to combine "Two E-series Shared ScanClk.vi" and
"High
> Speed Data Logger.vi" into another VI, and I have tried to read the stored
> data with the "High Speed Data Reader.vi". The problem is that I fight
with
> one error after another, what prevents me from going further.
>
> I use LabView 6.1, under Windows 2K.
>
> Has somebody by chance already done something similar and would agree to
> share with me their experience? TIA for any suggestion.
>
> Regards,
> Victor Manta
> >>
>
> "Ben" wrote in message
> news:[email protected]...
> > Hi Victor,
> >
> > I have done a lot of similar work.
> >
> > Exactly what did you try and what specific errors did you encounter?
> >
> > What you are trying is do-able provided the hardware you have suuports
> > it.
> >
> > Please post (both here and to the DAQ group)
> > the details of the hardware you are using,
> > versions of software being used,
> > Examples that you are using,
> > error codes that occured,
> > posibly post example code showing the problem.
> >
> > Ben
>
> Hi Ben,
>
> I use two PCI-MIO-16E-1 cards, connected by RTSI. I'd like to stream the
> data from both cards in real time to a binary file, after having added a
> header to it.
>
> For tests, on the channel 0 of each card is applied the same square wave,
> 100 Hz.
>
> Yes, the hardware support RTSI. I use LabView 6.1.
>
> Till now I have:
>
> 1. Combined the "Two E-series Shared ScanClk.vi" and the "High
> Speed Data Logger.vi" into a DAQ VI. To do this, I have "doubled" and
> adapted the "High Speed Data Logger.vi". For testing purposes the data are
> stored in two files, always the same ones (the old ones being overwritten
> after each acquisition).
>
> 2. "Doubled" and adapted "High Speed Data Reader.vi" into another VI, for
> reading from both files, mentioned earlier.
>
> What already works:
>
> - The headers for both files are correctly stored (VI point 1.)
> - The acquired data from the first card (device 1) are correctly stored
(VI
> point 1.)
> - The VI (point 2.) that reads both files and displays the results works
>
> What doesn't work:
>
> - The acquired data from the second card aren't stored at all (VI point
1.)
> - An error message says: "Error -10608 occurred at AI Buffer Read.
Possible
> reason: NI-DAQ LV: No transfer is in progress for the specified resource."
>
> I think that I understand this message, but I don't know how to continue.
>
> The DAQ VI can be downloaded from (please click the link, then the link on
> that page; about 100K, zipped):
>
> http://www.swissheartnet.unibe.ch/labview.htm
>
> Thanks a lot in advance.
>
> Regards,
>
> Victor Manta
>
> PS. I don't know which DAQ group you mean. -
Q: Acquiring data using two E series devices connected by RTSI and streaming data to disk
I use two E series PCI Cards, connected by RTSI. I'd like to stream the data
from both cards to a binary file and to add a header to it.
I also need to somehow read (plot) the stored data, this with another VI.
The whole should be then integrated into an existing program, that used just
one acquisition card.
Till now I have tried to combine "Two E-series Shared ScanClk.vi" and "High
Speed Data Logger.vi" into another VI, and I have tried to read the stored
data with the "High Speed Data Reader.vi". The problem is that I fight with
one error after another, what prevents me from going further.
I use LabView 6.1, under Windows 2K.
Has somebody by chance already done something simi
lar and would agree to
share with me their experience? TIA for any suggestion.
Regards,
Victor Manta<< (My first posting)
I use two E series PCI Cards, connected by RTSI. I'd like to stream the data
from both cards to a binary file and to add a header to it.
I also need to somehow read (plot) the stored data, this with another VI.
The whole should be then integrated into an existing program, that used just
one acquisition card.
Till now I have tried to combine "Two E-series Shared ScanClk.vi" and "High
Speed Data Logger.vi" into another VI, and I have tried to read the stored
data with the "High Speed Data Reader.vi". The problem is that I fight with
one error after another, what prevents me from going further.
I use LabView 6.1, under Windows 2K.
Has somebody by chance already done something similar and would agree to
share with me their experience? TIA for any suggestion.
Regards,
Victor Manta
>>
"Ben" wrote in message
news:[email protected]...
> Hi Victor,
>
> I have done a lot of similar work.
>
> Exactly what did you try and what specific errors did you encounter?
>
> What you are trying is do-able provided the hardware you have suuports
> it.
>
> Please post (both here and to the DAQ group)
> the details of the hardware you are using,
> versions of software being used,
> Examples that you are using,
> error codes that occured,
> posibly post example code showing the problem.
>
> Ben
Hi Ben,
I use two PCI-MIO-16E-1 cards, connected by RTSI. I'd like to stream the
data from both cards in real time to a binary file, after having added a
header to it.
For tests, on the channel 0 of each card is applied the same square wave,
100 Hz.
Yes, the hardware support RTSI. I use LabView 6.1.
Till now I have:
1. Combined the "Two E-series Shared ScanClk.vi" and the "High
Speed Data Logger.vi" into a DAQ VI. To do this, I have "doubled" and
adapted the "High Speed Data Logger.vi". For testing purposes the data are
stored in two files, always the same ones (the old ones being overwritten
after each acquisition).
2. "Doubled" and adapted "High Speed Data Reader.vi" into another VI, for
reading from both files, mentioned earlier.
What already works:
- The headers for both files are correctly stored (VI point 1.)
- The acquired data from the first card (device 1) are correctly stored (VI
point 1.)
- The VI (point 2.) that reads both files and displays the results works
What doesn't work:
- The acquired data from the second card aren't stored at all (VI point 1.)
- An error message says: "Error -10608 occurred at AI Buffer Read. Possible
reason: NI-DAQ LV: No transfer is in progress for the specified resource."
I think that I understand this message, but I don't know how to continue.
The DAQ VI can be downloaded from (please click the link, then the link on
that page; about 100K, zipped):
http://www.swissheartnet.unibe.ch/labview.htm
Thanks a lot in advance.
Regards,
Victor Manta
PS. I don't know which DAQ group you mean. -
Same number range for two different series groups?
Dear all,
There are two scenarios
1.Normal export under bond case, series group is 20 and number range maintained,running number is 300016
2.Another scenario,where ARE1 document generation for Deemed exp customer(already customised) , series group is 30.
But, client requirement is , for this second scenario also, system should pickup running number range of series group 20(under bond case) as per excise legal requirement
Ie running number is for series group 20 is 300016
For the above deemed exp case (second scenario)it should pickup 300017
And again when they do under bond case(first scenario), it should pick up 300018 like that
Is it possible to maintain the same number range for two different series groups(20 and 30)?
Even if you maintain the same number range for 30, as per running number range of 20
Will the system update simultaneously the same number range for 20 and 30 series groups?
Please suggest the way.With two different series groups, it is not possible to have the same number range. Even if you maintain it, they will be treated independently.
Normally, you should not use different series groups if the same number range has to be used. In fact, the concept of series group has been developed to ensure that number ranges can be maintained separately.
Regards,
Aroop -
When i open a new document, my "width" and "lenght" add two zeros automatically to file size??? For example basic A4 size in mm is 210 00mm x 297 00mm? And i can´t do nothing about it! Why on earth?
This "error note" must have something to do about it?elppaelo,
You may try the list.
The following is a general list of things you may try when the issue is not in a specific file (you may have tried/done some of them already); 1) and 2) are the easy ones for temporary strangenesses, and 3) and 4) are specifically aimed at possibly corrupt preferences); 5) is a list in itself, and 6) is the last resort.
If possible/applicable, you should save curent artwork first, of course.
1) Close down Illy and open again;
2) Restart the computer (you may do that up to 3 times);
3) Close down Illy and press Ctrl+Alt+Shift/Cmd+Option+Shift during startup (easy but irreversible);
4) Move the folder (follow the link with that name) with Illy closed (more tedious but also more thorough and reversible);
5) Look through and try out the relevant among the Other options (follow the link with that name, Item 7) is a list of usual suspects among other applications that may disturb and confuse Illy, Item 15) applies to CC, CS6, and maybe CS5);
Even more seriously, you may:
6) Uninstall, run the Cleaner Tool (if you have CS3/CS4/CS5/CS6/CC), and reinstall.
http://www.adobe.com/support/contact/cscleanertool.html -
My ipad will not start. It is 1 year old...I have tried holding the two buttons and nothing..I have it connected to my desktop and it will make a ding noise but nothing comes up on the screen.
Frozen or unresponsive iPad
Resolve these most common issues:
• Display remains black or blank
• Touch screen not responding
• Application unexpectedly closes or freezes
http://www.apple.com/support/ipad/assistant/ipad/
iPad Frozen, not responding, how to fix
http://appletoolbox.com/2012/07/ipad-frozen-not-responding-how-to-fix/
iPad Frozen? How to Force Quit an App, Reset or Restart Your iPad
http://ipadacademy.com/2010/11/ipad-frozen-how-to-force-quit-an-app-reset-or-res tart-your-ipad
Black or Blank Screen on iPad or iPhone
http://appletoolbox.com/2012/10/black-or-blank-screen-on-ipad-or-iphone/
What to Do When Your iPad Won't Turn On
http://ipad.about.com/od/iPad_Troubleshooting/ss/What-To-Do-When-Your-Ipad-Wo-No t-Turn-On.htm
iOS: Not responding or does not turn on
http://support.apple.com/kb/TS3281
iPad: Basic troubleshooting
http://support.apple.com/kb/TS3274
Cheers, Tom -
I ordered my Macbook Air with Aperture two years ago. I now have an iMac - can I use that with Aperture in any way? I appreciate that it is a different computer but I am now the end user of both devices and I was just wondering if it was possible.
Thanks,
SeanThe answer would be in your software license agreement for Aperture. However if you cannot locate it you can ask in the Aperture forum, the link for that is:
https://discussions.apple.com/community/professional_applications/aperture
However I believe you can have Aperture installed on two machines however only one may be using it at a time.
On the new iMac launch the Mac App Store - Purchased - look for Aperture and download to your new machine. -
I just got my iPad, I have an iPod. When I go to put apps on my new ipad it says my apple ID Is disabled. I have reset the passwords. Somehow I have two id's? I've gone into settings for apps signed out and back in with the new p.w. I can't think of what else to do to get the disabled block off. Any ideas?? Thanks
See this Apple document for help...
http://support.apple.com/kb/ts2446 -
i have a serious (and bizarre!) issue with my novation impulse (Although i've tried it with two other keyboards and i still have the same problem) and its compatibility with mainstage 3.
the problem is best explained on the following one - page thread:
https://discussions.apple.com/thread/3951518?start=0&tstart=0
(Clearly i'm not alone in this problem, although i think i figured out what's going wrong a little more than he did...read on!)
his solution, to put mainstage in jump mode, is very unsatisfactory to me, as it bounces all of a sudden to drastically different settings.
basically, my analysis is that my controller is NOT receiving MIDI date from mainstage. in other words, mainstage knows what my controller is doing, but my controller doens't know what mainstage is doing.
let's say i turn the knob all the way to the right ... 127...and the virtual fader goes to the right like it's supposed to.
now...next...let's say i change to a different patch, where that same VIRTUAL fader is not at the max clockwise position..maybe it's only at 1pm. now when i turn the physical knob to the RIGHT, the midi data is still at 127 on the controller! it didn't "reset" to sync up with the new level (say 80 or so) setting on the new patch. so i can't increase that new setting of 80 by continuing to turn the knob to the right. i have to turn it all the way to zero,...and then continue PAST zero until the controller thinks that IT is at 0...at that point the controller and mainstage are in agreement, and things work fine....so bascially, the keyboard thinks the level is at max...but mainstage thinks the level is at 1pm.
i am using Logic 9, and i have a macbook pro 2.9 Ghz I7 with 8 gigs of memory and OS X 10.8.4Hi Josh,
Thanks for taking the time to contact us here a Novation for technical support. Lets continue to correspond via email so we can get your issue resolved.
Thanks.
Mike Towns -
i used to open many tabs in the same page and i move from one to other by mouse but since3 two days the tabs open in the same page normaly but i can't move from one to other when i clik with mouse on any tab it don't open/ do u have any solve for this
Start Firefox in <u>[[Safe Mode|Safe Mode]]</u> to check if one of the extensions (Firefox/Tools > Add-ons > Extensions) or if hardware acceleration is causing the problem (switch to the DEFAULT theme: Firefox/Tools > Add-ons > Appearance).
*Do not click the Reset button on the Safe mode start window or otherwise make changes.
*https://support.mozilla.org/kb/Safe+Mode
*https://support.mozilla.org/kb/Troubleshooting+extensions+and+themes
Maybe you are looking for
-
I have a HP Pavillion g series, and while I was watchign a ideo the sound automatically shut off. I thought I had hit mute by accident, but nothing seems to be working. There is an x over my icon http://i50.tinypic.com/igx1zl.jpg A friend had told m
-
Set waveform chart size to value 1000
Is there any possibility to set the size of waveform chart buffer to value >1000 in LabVIEW? Message Edited by Konigusko on 05-03-2006 09:40 AM
-
Disk utility taking forever to "Erase Free Space"!
i am trying to speed up my macbook so i read on http://www.makeuseof.com/tag/how-to-speed-up-your-mac-without-spending-any-cash/ that one way to speed up a mac is to "Erase Free Space" and when i did it, it was working fine but now its been "Creating
-
Home button isnt working.. What should i do? how does it costs to change the home button?
-
Hi, 1.Q After first time schedule, some activities are confirmed and some are partially confirmed. Now When i run schedule again, does dates of subsequent activity are changesd? If yes, then does system stores the first time schedule dates any where.