UCCX 8.02 - Call recordings have stopped

Hello,
Over the weekend our UCCX server crashed.  Since then call recordings have stopped.  I have restarted Cisco Desktop VoIP Monitor Service, checked to see if call is recording is enabled for the agents in Cisco Desktop Administrator, and also made sure that call recording is configured in Cisco Admin (plugin). 
I'm looking for any troublshooting steps, if anyone has any ideas please let me know.
Thanks,
Ayaz

Hi Ayaz,
Couple of others things to look at.
1. By any chance is the Recording Count (under UCCX Admin->System Parameters page) is set to "0", if so change it max allowed number.
2. Check the status of "Cisco Desktop Recording and Statistics Service" on each node by using the below command.
Command Syntax:
utils service [option] [service-name]
Refer page 37 of the below given UCCX CLI guide link.
Note: If you have HA setup, and if one of the node's Recording service is down, than only the alternate calls will be recorded. Because Recording is the only feature in UCCX which works in load balancing mode in HA deployments.
3. Check the free space available for Recording by using the below command.
Command Syntax:
show uccx recordings space
If so, please purge the recording files.
Command Syntax:
utils uccx recordings purge
Note: This command purges the oldest recording files first.
http://www.cisco.com/en/US/docs/voice_ip_comm/cust_contact/contact_center/crs/express_8_5/configuration/guide/uccx851cli.pdf
Try restarting the below services on Node1.
- Cisco Desktop Recording and Statistics Service
- Cisco Desktop VoIP Monitor Service
Also please make sure that the UCCX first node holds the mastership of all the feature services (you can restart the second Node this to happen so that all the servie mastership will be given to First node of UCCX).
If these things doesn't resolve your issues, you may need to contact Cisco TAC for further troubleshooting.
Hope it helps.
Anand
Please rate helpful posts by clicking on the stars below the right answers !!

Similar Messages

  • UCCX 7 Encrypt call recordings

    Howdy Netpros, I can't find anything in the documentation for UCCX 7 on encrypting call recordings. I assume this is not possible and we are looking into a seperate call recording solution that supports encryption, but does anyone have any ideas about what I can do now to encrypt the call recording files besides exporting them to .wav and making them inaccessible to the Supervisor application?
    Thanks!
    Brett

    Brett,
         UCCX doesn't natively support encrypted calls using SRTP.  In fact, it's a requirement to turn it off.  However if all you are worried about is encrypting the recordings, I would do the following:
    1.) Create a secure server that has adequate storage.
    2.) Create a script that copies over the .raw files every X (minutes,hours,days).  Basically you just need to copy over as often as you feel the need exists.
    3.) Use the built in Windows signing functionality to sign and encrypt the files.
    You now have encrypted recordings, the downside of which is you don't have a player for them.  To rectify this, you will need to allow a copy of the raw2wav to run on that server and use usernames that have the security token to unencrypt the data.  You could then also give that token to your call center supervisors and allow them to listen to the recordings using the token and then delete.
    It's not a perfect solution, but it may work.  Let me know if you have any questions about this.  You Windows team should be able to provide you details on the signing tokens as they have been a part of Active Directory and Windows for a couple of generations now.  Hopefully this will give you somewhere to start.
    Regards,
    Robert W. Rogier

  • UCCX 8.0: Missing call recordings

    Hello,
    I never had any issues on call recordings and archiving before. Calls were recorded fine and then archived/exported to a local server every week as wav file.
    But recently I have noticed that some wav files that we store are 1 KB in size, which ofcourse cannot be opened or played. And even for one day we only got a total of 3 wav recordings, which is not possible as we receive hundreds of calls a day.
    So far its rare, but I really need to know what is causing this? server storage? network issue? high utilization of server?
    or something else. We had a total of 8 Agents and just recently we increased them 16.
    Thanks in Advance.

    Hi Essam,
    Reference : UCCX 8.5 SRND page 44
    The agent call recordings are stored on the hard drive of the Cisco Unified CCX server with agent data store locator records pointing to the actual recording files. The call recordings in Cisco Unified CCX are stored in a raw format that is only playable using the CSD Record Viewer. The CSD Record Viewer shows 7 days worth of call recording as well as those tagged for 30-day extended archiving. The CSD Record Viewer also provides the supervisor the option to save selected individual recordings into a .wav format in a specified folder.
    The amount of disk storage allocated for recordings on a single server non high availability deployment of Cisco Unified CCX is 2.6 GB. On a two server high availability deployment of Cisco Unified CCX, the recordings are alternated between the two servers in a round robin fashion to provide load balancing and redundancy. Hence the amount of disk storage allocated on each server is 1.3 GB.
    The recording capability of Cisco Unified CCX is not intended for usage as a permanent recording archival solution. However, an export utility is also available to bulk export all recordings into a .wav format. The export utility has no ability to specify selected recordings and will export all recordings on the Cisco Unified CCX server. System administrators could build their own customized command macros or process that would perform regular (at least weekly) exporting of the recordings for permanent archival of agent call recordings.
    Hope it helps,
    Anand

  • HT201401 My speaker does not work it just stopped right in the middle of the call, I have restarted the phone and it still doesn't work!! What.do I do?

    My speaker stopped working right in the middle of a call, I have reset my phone and powered off and back on
    And it still will not work, I can hear sound trying to come
    Thru randomly and goes right back out!! :( what do I do to fix this??

    http://support.apple.com/kb/TS2802

  • Continuous Disconnections "Appear" To Have Stopped...

    BACKGROUND (cutting a VERY long story "long")  [skip to the next section if you're bored to tears]:
    - With BT Broadband since early February. Had continuous disconnections since joining, which added to the dreaded DLM from BT resulted in ever-slow speeds (at some popint we wre under 0.1 Mbps)
    - Previously with Virgin Media BroadBand + BT line rental. We never had any issues of disconnections or slow speeds. Couldn't fault VM (except that they got riff of their BB customers to focus on Fibre services not available in our area).
    - The first-tier of Customer Services are all very polite people but, frankly, have been of no help at all. Countless line checks were made, mostly "concluding that the line was OK and the connection stable". Well, one only had to check the Event Logs, which would soon be out of memory within a day, showing disconnection after disconnection.
    - The second-tier could not help also and finally decided an engineer had to call at the property.
    - The engineeer failed to show up.
    - The engineer visit was rescheduled, the engineer did show up. He confirmed our internal installation is OK, put the onus on some
    work needed "down a manhole in a road nearby" and that a different team had to take over.
    - As far as I am aware, this work had been seen to (although I initially had my doubts: BT phone services told me "everything (was) sorted now" whilst I was tearing out my hair with the same problems and speeds under 0.1 Mbps
    - I *think* that my profile was reset once or twice by now, our speeds would get about 6 Mbps, rapidly dropping after
    disconnections.
    - I have noticed BB disconnections when using the internet on my Pc but ALSO when the PC was off and there was no wired or wireless use whatsoever.  
    - BT KEEPS CLOSING UP THE FAULTS I OPEN & RE-OPEN (HOW VERY CONVENIENT!) OUR FAULT HAS BEEN PRESENT FOR NEAR 3 MONTHS NOW, IS THAT TOO EMBARRASSING TO DISPLAY IN bt.com/fault?
    - Online complaint filed... Ignored by BT.
    - 3-page letter of complaint sent to BT... Got an awfully generic reply: "Hopefully you know by now what BT is doing to sort this problem" I DO ACTUALLY KNOW... THEY ARE DOING ABSOLUTELY NOTHING!  BT gave an email address to reply: I replied 7 days ago asking what's going on, now have re-sent the e-mail (2 days ago): Nothing. MAYBE THE SUPPLIED OMBUDSMAN CONTACT WILL NEED TO BE USED NEXT?
    - I keep being promised refunds of line rental, etc. These are yet to materialize as "I will get this when the fault is solved". This of course works on the assumption that my fault will EVER be solved. ALL I REALLY WANT IS: SORT THIS NEVERENDING FAULT.
    - Oh, and BT Direct Debit was increased to more than advised (yes, our experience was dreadful so far in ALL aspects) - We are dealing with this separately, DD has now been now reduced... I'm looking forward to the next quarterly bill to confirm I'm not being overcharged (I've honestly lost all trust in all things BT).
    - I am an engineer myself and the kindest assessment of the situation would be that BT Customer Services are applying ZERO LOGIC in trying to sort this problem.
    CURRENT SITUATION:
    - BT Customer Services appear to be avoiding us. They did not call us back to follow up the case and frankly, I am very busy these days and have little time to engage in another gruelling wait + futile conversation (typically near an hour in total) to get absolutely nowhere.
    - Stable connection for almost 7 days now.
    - Speed capped at 2 Mbps, actual speed is 1.4 to 1.5 Mbps (and has been so for at least 4-5 days).
    Onto the technical stuff........
    OUR CONNECTION:
    - Wired (ethernet) to desktop PC.
    - Hub4 Connected to test socket of NTE5, using supplied filter.
    - Only one phone connected, via the same filter at the main (test) socket.
    - At different times during troubleshooting (weeks ago), I took to, one by one, changing the filter, the ethernet cable and the phone cable supplied by BT. I also changed to different ethernet ports of the Hub, no joy... None of this made any difference so all original cables and filter are again in place.
    - The engineer neglected to check the HUb, convinced it was a line problem. Over a month ago, I temporarily replaced the Hub with an old Netgear supplied by Virgin. At that time this made no difference but then the disconnection rate was appalling and wonder if there was an actual fault in the line now and now this stabilized? Regardless, I've been thinking whether my old Netgear would perform better but I have been patient and trying to build up more days of stable connection... BUT 6 days+ of solid connection and I'm still at 1.4 Mbps????
    - There are NO other phones or telephone extensions at the property.
    - We occasionally use our mobile phones via wireless. Wireless connection is fine (when main connection is present, of course)
    Hub "Helpdesk" Info:
    1. Product name:    BT Home Hub
    2. Serial number:    +068340+NQ44321122
    3. Firmware version:    Software version 4.7.5.1.83.8.130.1.17 (Type A) Last updated Unknown
    4. Board version:    BT Hub 4A
    5. ADSL uptime:    6 days, 15:01:52
    6. Bandwidth:    96 / 1888
    7. Data sent/received:    229.6 MB / 3.5 GB
    8. Broadband username:    [xxedited_out_xx]@btbroadband.com
    9. BT FON:    No
    10. 2.4 GHz Wireless network/SSID:    [xxedited_out_xx]
    11. 2.4 GHz Wireless connections:    Enabled (802.11 b/g/n (Recommended)) 20 MHz, WPS enabled
    12. 2.4 GHz Wireless security:    WPA and WPA2
    13. 2.4 GHz Wireless channel:    Automatic / 6
    14. 5 GHz Wireless network/SSID:    [xxedited_out_xx]
    15. 5 GHz Wireless connections:    Enabled (802.11 n 40 MHz (Recommended)) 20/40 MHz, WPS enabled
    16. 5 GHz Wireless security:    WPA2
    17. 5 GHz Wireless channel:    Automatic / 40
    18. Firewall:    Default
    19. MAC Address:    d0:84:b0:e4:51:c6
    20. VPI/VCI:    0 / 38
    21. Modulation:    G.992.1 Annex A
    22. Latency type:    Interleaved
    23. Software variant:    -
    24. Boot loader:    -
    Noise Rates Margin and Line Rates of last "events" at the time of last noted disconnections (Note log dates, no updates since 15 April, when last disconnections occurred):
    04:50:49, 15 Apr.    (611767.630000) DSL noise margin: 7.00 dB upstream, 1.20 dB downstream
    04:50:49, 15 Apr.    (611767.560000) DSL line rate: 96 Kbps upstream, 1888 Kbps downstream
    04:48:38, 15 Apr.    (611636.000000) DSL noise margin: 28.00 dB upstream, 15.10 dB downstream
    04:48:38, 15 Apr.    (611635.920000) DSL line rate: 448 Kbps upstream, 7168 Kbps downstream
    04:48:04, 15 Apr.    (611602.640000) DSL noise margin: 13.00 dB upstream, 15.20 dB downstream
    04:48:04, 15 Apr.    (611602.560000) DSL line rate: 448 Kbps upstream, 1408 Kbps downstream
    04:45:30, 15 Apr.    (611448.390000) DSL noise margin: 28.00 dB upstream, 15.20 dB downstream
    04:45:30, 15 Apr.    (611448.320000) DSL line rate: 448 Kbps upstream, 7808 Kbps downstream
    04:45:06, 15 Apr.    (611423.970000) DSL noise margin: 14.00 dB upstream, 14.80 dB downstream
    04:45:06, 15 Apr.    (611423.900000) DSL line rate: 448 Kbps upstream, 1536 Kbps downstream
    BT Availability Checker:
    Telephone Number [xx_edited_out_xx] on Exchange LYNDHURST is served by Cabinet 6
    Featured Products / Downstream Line Rate(Mbps) / Upstream Line Rate(Mbps) / Downstream Range(Mbps) / Availability Date
    ADSL Max     Up to 8     --     7 to 8     Available
    Fixed Rate     2     --     --     Available
    BTWholesale Speed test:
    1. Best Effort Test: -provides background information.
    Download  Speed: 1.47 Mbps
    Max Achievable Speed: 2 Mbps
     Download speedachieved during the test was - 1.47 Mbps
     For your connection, the acceptable range of speeds is 0.4 Mbps-2 Mbps.
     Additional Information:
     Your DSL Connection Rate :1.89 Mbps(DOWN-STREAM), 0.1 Mbps(UP-STREAM)
     IP Profile for your line is - 1.5 Mbps
    Questions/Comments:
    - I thought it took 3 to 5 days of solid connection for broadband speed to be bumped up? How long should I now wait???
    - Does my IP profile need to be reset? (Note: I'm dreading that this will again result in 1-2 days of 6Mbps, followed by disconnections, followed by unusable sepeeds again, as this pattern a few times now).
    - Last DSL noise margin stats : "7.00 dB upstream, 1.20 dB downstream"... Any comments on this? Isn't 6 dB considered normal, and the lower this figure the better?
    - Can anyone help here before we abandon all hope, stop paying our bill and complain to Trade Standards/Ombudsman/etc??

    @ imjolly: Many thanks.
    I set the alarm 5 minutes early in order to restart the Hub this morning. Do I believe in coincidences? Sometimes... After 7 days of solid connection, several restarts occurred while my PC was off (Hub's always on) in the early hours of this morning.
    As such, I was correct in my cautiousness when naming the thread "Disconnections APPEAR To Have Stopped... " and I am now able to offer new stats without any manual intervention:
    06:06:35, 22 Apr.    ( 6977.200000) DSL noise margin: 16.00 dB upstream, 15.00 dB downstream
    06:06:35, 22 Apr.    ( 6977.130000) DSL line rate: 448 Kbps upstream, 2272 Kbps downstream
    06:03:52, 22 Apr.    ( 6814.210000) DSL noise margin: 15.00 dB upstream, 15.00 dB downstream
    06:03:52, 22 Apr.    ( 6814.140000) DSL line rate: 448 Kbps upstream, 2176 Kbps downstream
    06:01:57, 22 Apr.    ( 6698.960000) DSL noise margin: 16.00 dB upstream, 14.90 dB downstream
    06:01:57, 22 Apr.    ( 6698.890000) DSL line rate: 448 Kbps upstream, 2176 Kbps downstream
    06:00:35, 22 Apr.    ( 6616.720000) DSL noise margin: 27.00 dB upstream, 15.10 dB downstream
    06:00:35, 22 Apr.    ( 6616.650000) DSL line rate: 448 Kbps upstream, 7808 Kbps downstream
    05:53:58, 22 Apr.    ( 6219.650000) DSL noise margin: 15.00 dB upstream, 15.00 dB downstream
    05:53:58, 22 Apr.    ( 6219.580000) DSL line rate: 448 Kbps upstream, 2176 Kbps downstream
    05:39:17, 22 Apr.    ( 5339.020000) DSL noise margin: 16.00 dB upstream, 15.00 dB downstream
    05:39:17, 22 Apr.    ( 5338.950000) DSL line rate: 448 Kbps upstream, 2208 Kbps downstream
    05:38:52, 22 Apr.    ( 5314.130000) DSL noise margin: 11.00 dB upstream, 24.80 dB downstream
    05:38:52, 22 Apr.    ( 5314.060000) DSL line rate: 448 Kbps upstream, 3072 Kbps downstream
    04:11:23, 22 Apr.    ( 64.660000) DSL noise margin: 11.00 dB upstream, 14.90 dB downstream
    04:11:23, 22 Apr.    ( 64.500000) DSL line rate: 448 Kbps upstream, 1952 Kbps downstream
    Prior to disconnections I note in the main log entries like this one:
    04:09:57, 22 Apr.    (1214109.300000) PPP LCP Send Termination Request [User request]
    "User request" is not at all MY request... Does this indicate any manual intervention from BT? (I expect not, but I'm only curious). May post full logs if required.
    Thanks in advance for any help.

  • Question about the sensor... just got my 4s yesterday after screwing up my 3 with the laterd version update.  EVery call I have been on has either changed to speaker, called another number or ended the call or activated facetime, which I have turned off.

    Question about the sensor... just got my 4s yesterday after screwing up my 3 with the laterd version update. EVery call I have been on has either changed to speaker, called another number or ended the call or activated facetime, which I have turned off. never had this trouble with my 3...I don't even want to talk to anyone on this phone! Is the sensor bad? That is what the AT&t rep suggested.

    Restore as new... if the problem still continues then there is a hardware issue.
    If it stops after a restore as new, then the issue is with the backup the device is currently setup with.

  • Adjustment Brushes in Lightroom 3.6 have stopped working on my iMac

    I have Lightroom 3.6 loaded on my iMac v10.6 and have been using it continuously for some time.     For the second time in just a few weeks the Adjustment Brushes/Sliders have stopped working correctly, that is there is no noticeable adjustment on my image [for example Brightness, Exposure, Clarity etc.].      I cannot remember what I was told to do to correct this problem last time I had to contact Adobe Support about this issue,  and I'm told I now have to pay for support for this product now as Lightroom 4 is released.
    Is there a way I can fix the problem?
    Thank You.

    You've checked the density and flow sliders are set high enough?
    Resetting your preferences would be next port of call http://members.lightroomqueen.com/index.php?/Knowledgebase/Article/View/1148/198/how-do-i- delete-the-lightroom-preferences-file

  • Why do I keep getting the message "Contacts have stopped"?

    Frequently, when I am trying to answer or make a call, I get a pop-up message "Contacts have stopped" and I have to press OK in the message box before I can answer the call. If I'm trying to use Contacts to make a call, I have to keep pressing the Contacts button until the error message goes away and then Contacts will open. Is this just a glitch in my Motorola Droid Razr M or is this a system problem?

    modgma, that's a mystery to us too! Let's take a closer look into this matter for you. Did you recently receive a software update on your phone? Have you powered your phone off/on since this issue started?
    LasinaH_VZW
    Follow us on Twitter @VZWSupport
    If my response answered your question please click the "Correct Answer" button under my response. This ensures others can benefit from our conversation. Thanks in advance for your help with this!!

  • My iPhone 4s as stop working when l up day it to iOS 8.0.2 my app,s have stop working

    l have a iphone 4s and when l up day the phone to ios 8.0.2 thing have not been the same as my pass work and over have stop working like my app witness as stop working

    Problem solved!!
    Needs to go to Settings > Mail, Contacts and Calendar > Show on App Selector > Phones Favorites and Recents and disable both of then
    After go to phone app and clean recents calls, all of them.
    Problem Solved.
    Very very easy.
    Then u can turn on the bottoms phone favorites and recents without problem.
    regards,
    Raul

  • All my planned recordings have gone

    All my recordings have been deleted. I recently had a problem with my SKY+ HD box freezing so powered down and then back up again, unfortunately after doing this all my recordings had gone and were not in the deleted. I am really miffed about this as I had recorded the whole series of Game of Thrones and have now lost and cannot watch Grrrrrrrr Has anyone else experienced this ???

    Try the instructions below:
    Planner Rebuild
    If restarting your Sky+ box hasn't resolved the problem, follow these steps to rebuild the Planner.
    Please note: Rebuilding your Planner will not delete any of your previous recordings. However, it will interrupt any recordings currently in progress, so it's best to proceed when you’re not recording a programme.
    1. Press services on your Sky remote.
    2. Press the right arrow button to highlight Settings.
    3. Press select.
    4. Press 0, then 1, followed by select. You'll now see a new set of screens that are normally hidden from view, with the Setup screen selected.
    5. Press the left/right arrow buttons to highlight Sky+ Rebuild.
    6. Press select. You'll now see this message: "This will take a few minutes to complete. The rebuild will stop all recordings and reboot your Sky+HD".
    7. Press select. The onscreen message "Housekeeping please wait" will appear and then disappear within two minutes.
    8. The Planner rebuild will now go ahead, and may take up to two further minutes. Once complete, your Sky+ box will automatically switch itself off and then back on. You will then see the red standby light on your Sky+ box (newer boxes have an amber standby light).
    9. Wait for at least two minutes after the red standby light has appeared.
    10. Press sky on your remote control.
    Your Sky+ box should now start up as normal, with the light changing to green. Once your Sky+ box has started, try to use the Planner to record and view programmes as usual.

  • My sounds have stopped working for text, YouTube and music

    My sounds have stopped working for text, YouTube and music since in downloaded new software!

    I'm not sure if this will help, but I went into my sounds setting and made sure that both the "vibrate on ring" and "vibrate on silent" were selected to "on."  Once I did this, I was able to get the vibrating notification for a call received (as this had previously not been the case).  Hope this helps.

  • 3G iPhone click sounds have stopped working.

    For no apparent reason, the keyboard click sounds (feedback) have stopped working. Sounds from other apps work fine (audio), as well as iPod music, etc., but anything which gives a click sound feedback has stopped. I performed a sync, as well as went through all settings that have anything to do with sound or audio and it hasn't helped. I hate the idea of having to do a complete reset and reinstallation and configuration of everything, but what are my choices?
    TIA

    Not really stupid, some people don't even know their computer is unplugged when they see a dark screen and call tech support right away:-)
    But, Yes, I did a sync, I toggled all settings, I turned it off, accessed all typing apps, etc. Sound everywhere else works, just not keyboard click sound feedback. I am left to wonder if the actual click sound file itself got hosed and needs to be reloaded if that is possible - it seems that one can't access systems sounds to find out.

  • Hi, I've used four different Groups when emailing for the past few years, and suddenly they have stopped working. I've tried creating new Groups but that doesn't work either. I haven't changed or done anything different and it is driving me mad......

    Hi, I've used four different Groups when emailing for the past few years, and suddenly they have stopped working. I've tried creating new Groups but that doesn't work either. I haven't changed or done anything different and it is driving me mad......can anyone help, please?!

    Thanks for that information!
    I'm sure I will be calling AppleCare, but the problem is, they charge for the phone calls don't they? Because I don't have money to be spending to be on the phone with a support service.
    In other things, it seemed like the only time my MacBook was working was when I had Snow Leopard without the 10.6.8 update download that was supposed to be done to prepare for OS X Lion.
    When I look at the information of my HD it says that I have 10.6.8 but that was the install that it claimed to have failed and caused me to restart resulting in all of the repeated problems.
    Also, because my computer is currently down, and I've lost all files how would that effect the use of my iPhone? Because if it doesn't get fixed by the time OS 5 is released, how would I be able to upgrade?!

  • UCCX to generate calls on alerts

    Hello All,
    Has anyone ever tried or know if the following is possible with UCCX :
    We have network monitoring tools that sometimes generates alerts at night.
    We want it to be able to call some people on their GSM.
    We've tried other packaged tools but were not very efficient.
    Can we do that with a UCCX ?
    Monitor some alert (what ever their form maybe, we can adapt) and on that information, call with a specific prompt.
    UCCX would give the ability to control the number of calls and others things other tools wouldn't.
    Thanks

    Hi, yes, possible it is.
    I have a similar kind of monitoring solution.
    One more thing: this works with UCCX premium or IP IVR only, as HTTP triggers are used.
    I have an application server, running a container of various scheduled processes. Each process has its own specific task and specific object, for instance, network reachability (using ping) of the CUCM Publisher or disk state (using SNMP Get) of the ICM AW server.
    If a predefined threshold is reached, or simply put, a condition is evaluated to true, the process does a HTTP get request, triggering an UCCX application, with various parameters (like severity etc). The UCCX app then calls the engineer on duty (Place call), plays a message - and even writes a record into a database table whether the engineer picked it up, and the timestamp.
    Good luck.
    G.
    Sent from Cisco Technical Support Android App

  • My photos have stopped showing up on my pc from my iPhone.  They do still show up on my iPad.  I have signed out of iCloud on my pc and then signed in, but that didn't help.  Very puzzling.  Any help?

    My iphone photos have stopped showing up in my photo stream folder on my pc.  They do show up on my iPad.  I tried signing out and back into to iCloud on my pc, but no help.  Any ideas?

    The iCloud backup only backs up your camera roll photos, not photo stream photos.  Also, photos only remain in photo stream for 30 days.  After that they are removed from your photo stream, but will remain on your devices that already have them.  If all your photo stream photos are older than 30 days, that would explain why they don't stream to your iPhone 5 even though they are on your iPad.
    To get them on your phone, you can use an app like PhotoSync, which will wirelessly transfer photos from any album (including photo stream) between your devices.  Alternatively, you can save the photo stream photos to the camera roll on your iPad (by opening the My Photo Stream album, tap Edit, tap all the photos to select them, tap Share, tap Save to Camera Roll), then import them to your computer (see http://support.apple.com/kb/HT4083), put them in a folder, then select the folder on the Photos tab of your iTunes sync settings and sync them to your phone.

Maybe you are looking for