Unable to access Archived HR-Payroll data

Hi,
I have archived some data using the object PA_CALC. The file created was stored on the HTTP Content Server, and there was no error for the file stored.
When I tried retrieving the data using the FM "PA_READ_ARCHIVE_PA_CALC", I can retrieve data for some pernrs only.
On debugging I found out that the FM "ARCHIVE_READ_OBJECT" throws an exception i.e. FILE_IO_ERROR. What is confusing me is the file is read for some pernrs and not for some.
Could any body help me in this?
Vinod

I assumed you were far enough progressed that it was indexing .. perhaps it never made it that far.
Reset the TC to factory.. no files on the hard disk are lost.
Factory reset universal
Power off the TC.. ie pull the power cord or power off at the wall.. wait 10sec.. hold in the reset button.. be gentle.. power on again still holding in reset.. and keep holding it in for another 10sec. You may need some help as it is hard to both hold in reset and apply power. It will show success by rapidly blinking the front led. Release the reset.. and wait a couple of min for the TC to reset and come back with factory settings. If the front LED doesn’t blink rapidly you missed it and simply try again. The reset is fairly fragile in these.. press it so you feel it just click and no more.. I have seen people bend the lever or even break it. I use a toothpick as tool.
N.B. None of your files on the hard disk of the TC are deleted.. this simply clears out the router settings of the TC.
No files are lost.. just so you caught that.
People are scared but you cannot delete files by a reset of the hardware.
Redo the setup of the TC.. use all short names, no spaces and pure alphanumeric.
Reset TM..
Verify the backup.. see A4 and A5 here.. might be a little out of date.. but should be still near enough to figure out.
http://pondini.org/TM/Troubleshooting.html
Then have another go with TM.. but warning Yosemite has made a mess of it.. and / or the networking to the TC is so bad it doesn't work for that reason.
I strongly recommend what you have done.. use USB. Or use Carbon Copy Cloner or some other utility that actually works.. maybe if yosemite can keep the network up long enough.

Similar Messages

  • Unable to access Archived data with an ABAP Query

    I have an ABAP Query that uses Logical Database KDF (Vendor) for reporting.
    KDF is Archive Enabled and I can access archived document via SAP standard programs that used the KDF Logical Database.
    the query appears accessing the data but nothing shows on the report.
    Has anyone successfully written and ABAP query and included access to the Archived data?
    Any help is appreciated.

    Hi Gena,
    I'm facing exactly the same problem as you...
    Since this post is an old one, I imagine that you may not remember, but I have to try...
    Have you solved it? If yes, could you please tell me how?
    I've tried to use CL_ABAP_GZIP and CL_ABAP_UNGZIP_BINARY_STREAM and I'm getting the same error 30 at the  IctDecompressStream function.
    Tks in advance,
    Flavio.

  • Fox code: unable to access infocube data

    Hi Friends,
    Multi planning area consists of 2 basic areas. One infocube based on key figure model and other infocube based on account model.
    Now unable to access infocube(keyfigure model) data in multi area. Here my taget cube is based on account model.
    Operand display format is
    {Key Figure Name,Calendar Year/Month,Key Figure Type,Plng Area}.
    I haven't used any fields for condition. Below is excerpt of code.
    calmon is global varible with range 04.2006 to 03.2007
    DATA BPER TYPE 0CALMONTH.  'begin period
    DATA SPER TYPE 0CALMONTH.  'starting period
    DATA DPER TYPE 0CALMONTH.  'previous period
    DATA COUNTER TYPE I.
    SPER = VARI('CALMON',1).
    DO.
    BPER = TMVL(SPER,COUNTER).
    DPER = TMVL(BPER,-1).
    IF COUNTER > 0.
    Assign previous period closing stock to opening stock
    {ZQTY,BPER,000074,CASHFLOW} = {ZQTY,DPER,000079,CASHFLOW}.
    ENDIF.
    COUNTER = COUNTER + 1.
    Production from crushing(28.5%)
    {ZQTY,BPER,000076,CASHFLOW} =
    {ZCRUSHING,BPER,#,SPROPLAN} * (28.5 / 100).
    Raw Closing stock
    {ZQTY,BPER,000085,CASHFLOW} =
    {ZQTY,BPER,000084,CASHFLOW} -
    {ZRAWSUGAR,BPER,#,SPROPLAN}.
    IF COUNTER = 12.
    EXIT.
    ENDIF.
    ENDDO.
    Could any one of you help me out in this regard..appreciate ur help with points..
    thanks,
    RP
    I also tried by incorporating versions too..
    {Key Figure Name,Calendar Year/Month,Key Figure Type,Version,Plng Area}
    Plan version
    DATA NVER TYPE 0VERSION.
    NVER = VARV(PVER).              " returns globle variable value
    {ZQTY,BPER,000074,NVER,CASHFLOW} =
    {ZQTY,DPER,000079,NVER,CASHFLOW}.
    {ZQTY,BPER,000076,NVER,CASHFLOW} =
    {ZCRUSHING,BPER,#,FPV,SPROPLAN} * (28.5 / 100).
    FPV is final version of SPROPLAN(planning application)
    {ZQTY,BPER,000085,NVER,CASHFLOW} =
    {ZQTY,BPER,000084,NVER,CASHFLOW} -
    {ZRAWSUGAR,BPER,#,FPV,SPROPLAN}.
    thanks, ...RP
    I tried by inserting two fields  Fiscal yr & value type in "fields for condition" , still i'm not getting..what might be the reason?
    Is there any other way to achieve this?
    thanks...RP
    I'm already using standard area SPROPLAN in another multi-area, in that multi-area consists of 2 cubes both are based on key figure model only and correctly able to access the data for that application requirement, but here i'm not able to access SPROPLAN cube's data. I checked with different combinations. Any suggestions....
    thanks,..RP  
    Keyfigure ZCRUSHING of SPROPLAN plannning area is already accessed in just above mentioned mulit-area, is because of this, am i getting the problem? Is there any refresing setting i have to mention?...thanks
    Edited by: Kumar RP on Mar 27, 2008 1:51 PM
    Edited by: Kumar RP on Mar 28, 2008 7:42 AM
    Edited by: Kumar RP on Apr 1, 2008 6:53 AM
    Edited by: Kumar RP on Apr 2, 2008 11:20 AM

    Myself corrected code by using operand format as
    {Key Figure Name,Key Figure Type,Plng Area}.
    regards,
    RP

  • TS3992 My Icloud back up shows huge amount of data stored from back up yet listed as incomplete. Unable to access data. Is data lost

    My ICloud backup shows a huge amount of data stored, yet it is listed as incomplete backup. I am unable to access the backed up data. Is the data lost?
    Thank you in advance for your assistance.

    Unfortunately, if an iCloud backup is incomplete you can't access any of the data in it.  The only way to access anything in the backup is to restore the entire backup, which can't be done if it is incomplete.

  • Can SARI and DART access archived BI/BW files?

    We used SARI and DART to access archived ECC data.
    We wonder whether SARI and DART can also access archived BI/BW data.
    Would you please share your experience?
    Thanks!

    Hi Laura,
    unfortunately DART can only access the "normal" R/3 Application archive objects,
    such as FI_DOCUMNT
    br
    Attila

  • Unable to access the data from Data Management Gateway: Query timeout expired

    Hi,
    Since 2-3 days the data refresh is failing on our PowerBI site. I checked below:
    1. The gateway is in running status.
    2. Data source is also in ready status and test connection worked fine too.
    3. Below is the error in System Health -
    Failed to refresh the data source. An internal service error has occurred. Retry the operation at a later time. If the problem persists, contact Microsoft support for further assistance.        
    Error code: 4025
    4. Below is the error in Event Viewer.
    Unable to access the data from Data Management Gateway: Query timeout expired. Please check 1) whether the data source is available 2) whether the gateway on-premises service is running using Windows Event Logs.
    5. This is the correlational id for latest refresh failure
    is
    f9030dd8-af4c-4225-8674-50ce85a770d0
    6.
    Refresh History error is –
    Errors in the high-level relational engine. The following exception occurred while the managed IDataReader interface was being used: The operation has timed out. Errors in the high-level relational engine. The following exception occurred while the
    managed IDataReader interface was being used: Query timeout expired. 
    Any idea what could have went wrong suddenly, everything was working fine from last 1 month.
    Thanks,
    Richa

    Never mind, figured out there was a lock on SQL table which caused all the problems. Once I released the lock it PowerPivot refresh started working fine.
    Thanks.

  • I have an external hard drive from my time capsule that stopped working on me. I am attempting to access the data with a hard drive reader on my MAC. I am able to see the drive in disk utility and under system info USB. But I am unable to access the data.

    I have an external hard drive from my time capsule that stopped working on me. I am attempting to access the data with a hard drive reader on my MAC. I am able to see the drive in disk utility and under system info USB. But I am unable to access the data and it does not show on the desktop when connected.

    Ok if disk utility was able to verify the drive I doubt there is any problem.. are you trying to open a TM backup??
    You need to mount the sparsebundle then check the actual info inside the bundle.
    Don't use disk warrior.. if the disk has verified then unless you deliberately deleted files there is nothing that is going to do.
    Pondini has a lot of stuff about getting access to the sparsebundle.
    http://pondini.org/TM/17.html
    But if you have copied info to the TC that is now gone.. and the disk is ok.. I am not sure.. the TC will not have deleted the files itself.

  • Unable to access or view data with no authorization error

    Hi Experts,
    Appreciate your guys help. I am ID administrator where by some of our user ID unable to view data/ display report for the some of data even the appropriate authorization already assigned to the user. However when we check in the transaction SU53 - authorization checking no error shown!
    There is a case whereby user report that his ID (e.g. SAP ID = ABC) unable to access a transaction or infotype data for example HR infotype masterdata,upon checking there is no authorazition error (checked insu53), when copy the ID (ABC) to another new ID (ABC1) with no changes on the roles, the ABC1 ID able to access the said transaction.However, when copy back ABC1 to the ABC (naming conversion only), the ABC ID still unable to access the transaction with no authorization error. the
    main problem here is the original ID is not working, but works fine if it is copied to another ID name.
    Kindly advice.

    Hi Manikya Raju,
    Can you explain details?

  • Ora:12705 unable to access NLS data files or  invalid environment specified

    Hi All,
    In our BW production SAP standard job DBA:update_stats is failing  . In Job log we found that  the info like
    Ora:12705 unable to access NLS data files or  invalid environment specified.
    Connect to DB instance failed.
    Brconnect terminated with exit code 3.
    We are on Oracle 10.2 BW 3.5  Sunsolaris 5.10
    The Env is as below:
    HOME=/home/bwpadm
    PATH=/oracle/BWP/102_64/bin:/usr/jdk/j2sdk1.4.2_13/bin:/home/bwpadm:/usr/sap/BWP/SYS/exe/run:/etc:/usr/bin:.:/opt/EMCpower/bin/64:/etc/emc/bin:/usr/ccs/bin:/usr/ucb:/usr/openwin/bin
    LOGNAME=bwpadm
    HZ=
    TERM=vt100
    SHELL=/bin/csh
    MAIL=/var/mail/bwpadm
    TZ=US/Pacific
    PWD=/home/bwpadm
    USER=bwpadm
    SAPSYSTEMNAME=BWP
    DIR_LIBRARY=/usr/sap/BWP/SYS/exe/run
    LD_LIBRARY_PATH=/usr/sap/BWP/SYS/exe/run:/opt/j2sdk1.4.2_08/bin
    JAVA_HOME=/usr/jdk/j2sdk1.4.2_13
    THREAD=NOPS
    dbms_type=ORA
    dbs_ora_tnsname=BWP
    dbs_ora_schema=SAPBWP
    ORACLE_PSRV=BWP
    ORACLE_SID=BWP
    DB_SID=BWP
    ORACLE_HOME=/oracle/BWP/102_64
    ORACLE_BASE=/oracle
    ORA_NLS33=/oracle/client/92x_64/ocommon/nls/admin/data
    NLS_LANG=AMERICAN_AMERICA.WE8DEC
    SAPDATA_HOME=/oracle/BWP
    Plz suggest what we have to change to fix the problem.
    Thanks,
    Subhash.G

    Thanks for the reply,
    The below is the orasid env:
    As you suggest  we  found ld_library_path  is not set to  oracle client .
    we still using 9.x client shall we add that path to the above varaible.
    Please suggest..
    HOME=/oracle/RSS
    PATH=/oracle/RSS/102_64/bin:/oracle/RSS:/usr/sap/RSS/SYS/exe/run:/etc:/usr/bin:.:/opt/EMCpower/bin/64:/etc/emc/bin:/usr/ccs/bin:/usr/ucb
    LOGNAME=orarss
    HZ=
    TERM=vt100
    SHELL=/bin/csh
    MAIL=/var/mail/orarss
    TZ=US/Pacific
    PWD=/oracle/RSS/102_64/dbs
    USER=orarss
    SAPSYSTEMNAME=RSS
    DIR_LIBRARY=/usr/sap/RSS/SYS/exe/run
    LD_LIBRARY_PATH=/usr/sap/RSS/SYS/exe/run:/oracle/RSS/102_64/lib
    THREAD=NOPS
    dbms_type=ORA
    dbs_ora_tnsname=RSS
    dbs_ora_schema=SAPRSS
    ORACLE_SID=RSS
    DB_SID=RSS
    ORACLE_BASE=/oracle
    ORACLE_HOME=/oracle/RSS/102_64
    NLS_LANG=AMERICAN_AMERICA.UTF8
    SAPDATA_HOME=/oracle/RSS.
    Thanks,
    Subhash.G

  • I am from India using my iphone4 with Vodafone and  firmware version 5.0.1(9A405). I am unable to access 3G from my device as the CELLULAR DATA NETWORK option in the settings is missing. Any methods or options for fixing the same????

    I am from India using my iphone4 with Vodafone and  firmware version 5.0.1(9A405). I am unable to access 3G from my device as the CELLULAR DATA NETWORK option in the settings is missing. Any methods or options for fixing the same????

    I am from India using my iphone4 with Vodafone and  firmware version 5.0.1(9A405). I am unable to access 3G from my device as the CELLULAR DATA NETWORK option in the settings is missing. Any methods or options for fixing the same????

  • TS3297 I keep trying to purchase something in the iStore but it comes up with "Your account is temporarily unavailable"  "Store unable to access my account info"  But I have checked my account info and everything is up to date.

    I keep trying to purchase something in the iTunes Store but it comes up with "Your account is temporarily unavailable"  "Store unable to access my account info"  But I have checked my account info and everything is up to date. 
    I have some money from a card still on my account that I would like to use.

    This has been an issue with some users for close to 24 hours now. I've been getting the error for the last 5 or so hours myself.
    Having problems is understandable, it happens. and if this is related to the iCloud hack reported yesterday it is good to know Apple is trying to fix the issue.
    But it sure would be nice if there was an official statement from Apple concerning this.

  • Does the Transaction FERD has the capability to access  archived data?

    Hi All,
    Does the Transaction FERD has the capability to access  archived data?
    Regards
    Prathima

    You need to set up a Personal Hotspot account with your cell carrier for your iPhone. Once it is activated you can turn it on in Settings on your iPhone then connect your iPad either via Bluetooth or WiFi. I would recommend WiFi. The BT on the iPad can be used for tethering.

  • Unable to access data n 0PY_PP_C3  ODS

    Hi,
    We have extracted Payroll data and consolidated data is sitting in "Auditing and Postings Combined" ODS.
    When I try to see the contents, its saying that I don't have authorization to see the same.
    HR Functional Team is trying to access this data. Which ROLE and Authorization, we should have.
    Its urgent. Please do let me know,

    Hi Anand,
    Normally the users are not given authroization for HR Cubes/ODS. Goto PFCG -> find the corresponding role and add yourself to that role.
    Bye
    Dinesh

  • I am unable to access iTunes.  Receive error regarding data execution prevention.  I've tried unloading/reloading.  Suggestions?

    I am unable to access iTunes.  Receive error regarding data execution prevention.  I've changed the Performance Options to exclude DEP for iTunes and I've tried unloading/reloading.  Still no success.  Suggestions?

    Try updating your QuickTime to the most recent version. Does that clear up the DEP errors in iTunes?

  • Ask your question.PPC Mini running 10.4.11 unable to access urls based on Javascript.  Software up to date.  Cannot find where to verify if JavaScript turned off.

    PPC Mini running 10.4.11 unable to access urls based on Javascript, get "Javascript void" at bottom of window..  Software up to date.  Cannot find where to verify if JavaScript turned off.

    I guess I verified this in following earlier IIIasss recommendations (whom I will respond to in detail after this).
    I have used Firefox (cookies deleted after each session) successfully with this site (Zinni Optical), but something has changed over the last year and a half and, to my knowledge it isn't on my end.  When I get response at all, and try to navigate to "My Favorites, etc., and nothing happens for a while, I try to refresh, only to get a "stopped" message with a blank screen.
    Tried Safari and Internet Explorer browsers (all I presently have installed) without succerss.  May go back to TenFourFox (which had it's own wierdness over time, which is why I uninstalled it.  Don't know latest versions compatible with 10.4.11 of Safari (but Software update is satisfied I'm up to date) or Internet Explorer.
    I'm out in the sticks using a Verizon (Novatel) MiFi in a metal building, and so require a Wilson external antenna, liightening arrestor, signal amplifier and inside rebroadcast antenna to boost cell phone  signal from one to four bars.  Hope I get similar boost for  wireless-Airport connection, understand that is different frequency, but also boosted.
    The site for the bank I do WebBillpay with has had a minor change...no longer do I get the option to sign off (six months to a year ago), otherwise, fine.

Maybe you are looking for