Unable to deploy application to iPhone (original) after updating Xcode from 4.1 to 4.2.1
When I try to debug the application on my iPhone (1st generatino, the original, non-3g one), it says "Build succeeded" and "finished running application" , but it doesn't seem to actually run it.
It seems to run fine on my 4th Generation iPod touch though.
Is there some setting or switch I need to flip?
Which iOS is on it?
Did you install debug support for the iOS on that device?
Similar Messages
-
there is no sim card installed in the iphone error after update software from 4.1 to 5.01(iphone 3gs)
Thanks for reply, but problem is diffrent I got updated my device via I tune(IPSW 5.01) before that, it was working well after upgreade 4.1 to 5.01 I am getting problem. No cydia no signal!
BTW Thank you, -
Unable to sync app to iphone 4 after update to iOS 6.0.1?
I have updated my iphone 4 to iOS 6.01 today..everything went fine and d restore happened..when d app started syncing...few of apps synced and thn my computer crashed..after restart no app are getting synced..why is this happening...before d comp crashed d apps were syncing fine...plz help!!
Hi,
Follow this article for instructions on completely re-installing the iOS operating system; it sounds like some file may have gotten corrupted during your iOS 7 install.
It's a good idea to back up your data first (to iCloud or iTunes), restore the iPhone to factory settings through iTunes, and then temporarily set the iPhone up as new to test the camera with a completely fresh copy of iOS. If it still doesn't work after re-installing iOS 7 and setting up as new, you may have a hardware issue.
Good luck! -
i am unable to set up my iphone 5 after reset since am getting a error stating 'unable to reach server' . i tried restoring the same from my computer but i get a error stating server unavailable' . please help me as my phone is stuck at the set up page. so i have already tried recovery mode as well.
Contact Apple support for warranty service.
-
I am unable to activate my iphone 3gs after updating ios 6.1.3
i am unable to activate my iphone 3gs after updating ios 6.1.3?
The activation servers were down for a bit yesterday.
Try again.
A SIM is required for activation. If problems continue, the two most common activation issues are the result of a hacked or jailbroken device. -
What could be the possible reason for a deployed application to run slow after the target pc comes out of standby mode? PC running XP and using the USB to communicate with the DAQ and driver boards. Application generated with 2010.
ThanksHello,
Usually default property is checked
system property -> devices ->usb root -> power management -> allow system to switch off device
Hope this help
Regards
Tinnitus
CLAD / Labview 2011, Win Xp
Mission d'une semaine- à plusieurs mois laissez moi un MP...
RP et Midi-pyrénées .Km+++ si possibilité de télétravail
Kudos always accepted / Les petits clicks jaunes sont toujours appréciés
Don't forget to valid a good answer / pensez à valider une réponse correcte -
HT4623 i use iPhone 3gs, after updating am unable to activate my iPhone how do i go about it
i use iPhone 3gs, after updating am unable to activate my iPhone how do i go about it
That's almost always because the phone was hacked or jailbroken to unlock it.
-
Dll Created In: - MFC VC
6.0
Application Exe Developed In:
- VC 6.0, C# and VB.net (Applications which are using dll)
OS: - Windows XP sp2 32bit
/ Windows Server 2008 64 bit
Problem: - Facing problem in creating socket
in a method from an already deployed application exe while same method is working from another exe from same environment from same location.
Description: - We have product component which
has an exe component and from exe we invoke a method, which is defining in dll, and that dll is developed in MFC VC6.0. In the dll we have a method which downloads images from another system after making socket connection. But every time we are getting Error
code 7, it is not giving desire result while same method is working from another exe from same environment from same location. And also me dll is deployed on many systems and giving proper output from same application.
Already Attempt: - Because error is coming on
client side so what we did, we created a driver in C# which invokes same method from same environment(on client machine) using same dll and we are astonished because it worked fine there.
Kindly Suggest: -
We are not able to figure out root cause because nothing is coming in windows event logs but what I did, for finding the problem line, I wrote logs on each line and found the exact line in application exe which is not working,
actually it is not executing Create () method,
I will give snippet of the code for understanding the problem because we are not finding any kind solution for it.
Kindly assist us in understanding and fixing this problem.
Code Snippet: -
Int Initialize (LPTSTR SiteAddress, short PortId)
try
CClientTSSocket *m_pJtsSockto;
m_pJtsSockto = new CClientTSSocket;
LONG lErr = m_pJtsSockto->ConnectTS(csIPAddress,PortId);
ErrorLog (0, 0, "--------ConnectTS has been called ------------","" );
catch(...)
DWORD errorCode = GetLastError();
CString errorMessage ;
errorMessage.Format("%lu",errorCode);
ErrorLog (0, 0, "Image System", (LPTSTR)(LPCTSTR)errorMessage);
return IS_ERR_WINDOWS;
Note: -
CClientTSSocket extends CAsyncSocket
IS_ERR_WINDOWS is a macro error code which value I found 7.
LONG ConnectTS(CString strIP, UINT n_Port)
ErrorLog(0,0,"ConnectTS is calling Create [is going to call]","");
if(!Create())
ErrorLog(0,0,"ConnectTS is calling [Create not called successfully] ","");
n_Err = GetLastError();
ErrorLog(n_Err,0,"ConnectTS is calling1111111111111111Erorrrrrrrrrrrrr","");
return NET_INIT;
ErrorLog(0,0,"ConnectTS is calling2222222222222222222","");
if(!AsyncSelect(0))
n_Err = GetLastError();
return NET_INIT;
if(!Connect(strIP,n_Port))
n_Err = GetLastError();
ErrorLog(n_Err,0,"ConnectTS","");
return SERVER_NOT_CONNECTED;
Code description: -
From
int GETImage_MT() method we call Initialize() method and pass client machine IP and Port and there we call
ConnectTS() method, In this method we Create() method and finally it returns the error code as mention in macro 7.
Logs after running the program: -
--------ConnectTS has been called ------------
ConnectTS is calling Create [is going to call]
Image System
0
Note: - According to logs, problem is coming in Create method().
Here 0 is errorMessage received in catch block. And from catch block it returns macro value 7. And when we run same method individually from same machine, same environment through same dll
from different exe, it is working fine and we are facing any kind of problem. While same problem application was working properly earlier but now continuously it showing problem.
Kindly assist us to resolve the issue.Pointer variable was already initialized; I have mention in code; kindly assist us.
Dll Created In: - MFC VC 6.0
Application Exe Developed In: - VC 6.0, C# and VB.net (Applications which are using dll)
OS: - Windows XP sp2 32bit / Windows Server 2008 64 bit
Problem: - Facing problem in creating socket
in a method from an already deployed application exe while same method is working from another exe from same environment from same location.
Description: - We have product component
which has an exe component and from exe we invoke a method, which is defining in dll, and that dll is developed in MFC VC6.0. In the dll we have a method which downloads images from another system after making socket connection. But every time we are getting
Error code 7, it is not giving desire result while same method is working from another exe from same environment from same location. And also me dll is deployed on many systems and giving proper output from same application.
Already Attempt: - Because error is coming
on client side so what we did, we created a driver in C# which invokes same method from same environment (on client machine) using same dll and we are astonished because it worked fine there.
Kindly Suggest:
- We are not able to figure out root cause because nothing is coming in windows event logs but what I did, for finding the problem line, I wrote logs on each line and found the exact line in application exe which is not
working, actually it is not executing Create () method, I will give snippet of the code for understanding
the problem because we are not finding any kind solution for it. Kindly assist us in understanding and fixing this problem.
Code Snippet: -
Int Initialize (LPTSTR SiteAddress, short PortId)
try
CClientTSSocket *m_pJtsSockto;
m_pJtsSockto = new CClientTSSocket;
LONG lErr = m_pJtsSockto->ConnectTS(csIPAddress,PortId);
ErrorLog (0, 0, "--------ConnectTS has been called ------------","" );
catch(...)
DWORD errorCode = GetLastError();
CString errorMessage ;
errorMessage.Format("%lu",errorCode);
ErrorLog (0, 0, "Image System", (LPTSTR)(LPCTSTR)errorMessage);
return IS_ERR_WINDOWS;
Note: - CClientTSSocket extends CAsyncSocket
IS_ERR_WINDOWS is a macro error code which value I found 7.
LONG ConnectTS(CString strIP, UINT n_Port)
ErrorLog(0,0,"ConnectTS is calling Create [is going to call]","");
if(!Create())
ErrorLog(0,0,"ConnectTS is calling [Create not called successfully] ","");
n_Err = GetLastError();
ErrorLog(n_Err,0,"ConnectTS is calling1111111111111111Erorrrrrrrrrrrrr","");
return NET_INIT;
ErrorLog(0,0,"ConnectTS is calling2222222222222222222","");
if(!AsyncSelect(0))
n_Err = GetLastError();
return NET_INIT;
if(!Connect(strIP,n_Port))
n_Err = GetLastError();
ErrorLog(n_Err,0,"ConnectTS","");
return SERVER_NOT_CONNECTED;
Code description: - From int GETImage_MT() method
we call Initialize() method and pass client machine IP and Port and there we call ConnectTS() method, In
this method we Create() method and finally it returns the error code as mention in macro 7.
Logs after running the program: -
--------ConnectTS has been called ------------
ConnectTS is calling Create [is going to call]
Image System 0
Note: - According to logs, problem is coming in Create method(). Here
0 is errorMessage received in catch block. And from catch block it returns macro value 7. And when we run same method individually from same machine, same environment through same dll from different exe, it is working fine and we are facing any kind of problem.
While same problem application was working properly earlier but now continuously it showing problem.
Kindly assist us to resolve the issue. -
I'm using Iphone 5 .After updating it with the latest software i.e iOS 7.0.6 I'm not able to see the wats app and imsg on my notification center when my phone is locked until and unless i activate the "Show on Lock Screen" under each application. which was not same as in the earlier software version.I dnt want my messages or watsapp msges to be displayed on home screen when locked but should be displayed on the notification center on lock condition.
Please suggest a solution or @Apple please get a software release which can remove this bug .We aren't Apple, just users like you. Have you tried a reset? Hold down the home button along with the sleep/wake button until the screen goes black and you see the Apple, then let go. (No data loss)
-
Unable to send or receive text messages after updating iOS to 7.0.2
I am unable to send or receive text messages aftering updating to iOS 7.02. I have an iPhone 4S. I have run all the suggested troubleshooting still can't text. I have been to my carrier, AT&T, there is no issue with my account. AT&T suggested resetting the phone to factory defaults (thereby wiping it clean). I am trying to avoid that as I had issues with transferring data & contacts before. Any one have a work around?
Try this iMessage workaround
Look for a fix by Apple by the end of the week..... -
TS1363 i could not activate my iphone 3G after updating to ios 6.0.1
i could not activate my iphone 3G after updating to ios 6.0.1
Generally this is a sign that the iPhone had previously been
hacked/modified/jailbroken and the update relocked it to the
original wireless carrier. If this is the case, only that wireless
carrier can unlock your iPhone. You must contact them to see
if they offer unlocking and if you qualify.
If the iPhone was advertised as unlocked and you are still within
the return period, start a claim with eBay to get your money back.
What wireless carrier did you use before this problem?
Does the app Cydia appear on your iPhone?
What does it say when you look at Settings=>General=>
About=>Carrier? -
HT201210 how to activate iphone 4 after updating software to IOS 6?
how to activate iphone 4 after updating software to IOS 6?
please help..Your friend did an unofficial unlock and it has now locked back to the original cell carrier. You need to call AppleCare, give them the model and serial number of the iPhone and find out which cell carrier it is locked to. Then contact that cell carrier and see what the process is to officially unlock the iPhone and if you qualify.
-
I have iphone 4s after update ios7 "There is no SIM card installed"
i have iphone 4s after update ios7 "There is no SIM card installed" i purchased from austuralia but now i am in egypt and i made the update here but the result my iphone not working now with any sim card
what can i do?Maybe the SIM card is faulty one has not bee inserted correctly. Take the sim out and reinsert it. Try a different sim. Maybe the phone was hacked to unlock it from the original carrier and when you updated it it relocked
-
please help.
MY IPHONE 4S, AFTER UPDATE TO IOS 7.0.6, BEING RESET AND LOCK BY ICLOUD. AND FORGOT THE PASSWORD. COULD I do ANY THING ?The Apple ID and Password that was Originally used to Activate the iDevice is required
If you do not have that information you will not be able to use the Device.
Activation Lock in iOS 7 > http://support.apple.com/kb/HT5818 -
how im suppose to fix the auto shutdown problem in my iphone 3gs after updating to ios 5.1.1 this problem has made me a mobile ****** in my house and an loser in thing care so if any solution to this problem let me know
What "auto shutdown problem" are you talking about?
Maybe you are looking for
-
hi all, hope all r doing fine? anyway i have a query which is mentioned below:- select field1,.....fieldn from <dbtable1> into corresponding fields of table itab where <condition>. select field1,...fieldn from <db
-
Queries on DATABASE OPEN RESETLOGS and lost Control Files
Hi I have some queries on RESETLOGS I would be keen to hear some answers on Q1. If I am doing a PITR and I end in ALTER DATABASE OPEN RESETLOGS, what happens about any Archived Redo Log files ( still in situ ) that were from the original source datab
-
Using a Sql Result in Default Value of Dashboard Prompt
Hi, I Create a Dashboard Prompt, this have two dates, the initial and the last for a period to filter. I need to set the default value in the fist and last date of the previous month, for example, if today is 20th of november the default value of ini
-
How do I remove my Address Book folder from dropbox on my old Imac and move it to my new mac so I can use icloud
-
FIREFOX FAILED TO INITIALIZE (0x0000034 WON'T OPEN AT ALL
used revo to unintall v3... dowloaded and installed v4.0 will not open at all. I think I deleted some critical file when using revo. I NEED HELP BIGTIME !!