Unable to GUI into an 4710 appliance
Hi..we have a pair of 4710 appliances and we're able to ssh and HTTPS into one, but not HTTPS into the other. Is there a "lighting rod" as far as configuring the GUI access on the 4710 appliance?
Thanks
I am not getting a login page at all for the primary ACE, but getting a full login page and able to login to the stand-by device. The Admin Context between the two contexts are identical. Below is the Admin Context config:
logging enable
logging buffered 6
resource-class ABC
limit-resource all minimum 75.00 maximum unlimited
boot system image:c4710ace-mz.A3_2_0.bin
peer hostname LB2-A
hostname LB2-S
interface gigabitEthernet 1/1
channel-group 1
no shutdown
interface gigabitEthernet 1/2
channel-group 1
no shutdown
interface gigabitEthernet 1/3
channel-group 1
no shutdown
interface gigabitEthernet 1/4
channel-group 1
no shutdown
interface port-channel 1
switchport trunk allowed vlan 201-204
no shutdown
clock timezone standard EST
class-map type management match-any ACCESS
2 match protocol https any
3 match protocol icmp any
5 match protocol ssh any
policy-map type management first-match REMOTE-ACCESS_PL
class ACCESS
permit
interface vlan 202
ip address 10.11.202.251 255.255.255.224
peer ip address 10.11.202.250 255.255.255.224
service-policy input REMOTE-ACCESS_PL
no shutdown
ft interface vlan 203
ip address 10.11.202.10 255.255.255.224
peer ip address 10.11.202.11 255.255.255.224
no shutdown
ft peer 1
heartbeat interval 300
heartbeat count 10
ft-interface vlan 203
query-interface vlan 202
ft group 1
peer 1
priority 75
associate-context Admin
inservice
ip route 0.0.0.0 0.0.0.0 10.11.202.254
context GAP
allocate-interface vlan 201-202
allocate-interface vlan 204
member ABC
context GAPDev1
allocate-interface vlan 201-202
allocate-interface vlan 204
context GAPQA1
allocate-interface vlan 201-202
allocate-interface vlan 204
snmp-server community GAP-MEDI group Network-Monitor
ft group 2
peer 1
priority 75
associate-context GAP
inservice
Thanks..
Similar Messages
-
ACE 4710 Appliance GUI configuration
I am having an issue with configuration of the GUI for the 4710. If I am using local authentication, the GUI works fine. However when I turn on aaa and use radius to authenticate, I am unable to log into the GUI.
When I place the 4710 into debug for aaa, I am sucessfully authenticating. My radius server's logs state the same.
Has anyone run across this?Are you able to login to the CLI using AAA? Have you configued the role and domain for the user on your AAA server? Here is some documenation on configuring the role and domain for a use on the AAA server:
http://www.cisco.com/en/US/docs/app_ntwk_services/data_center_app_services/ace_appliances/vA1_7_/configuration/security/guide/aaa.html#wp1321891 -
Hi,
I have ACE 4710 Appliance, but it is failed and giving following error while login at console.....
I am suspecting hardware issue..most probably with harddrive.... Please let me know if it can be recoverable of only replacement is the solution..
switch login: init: failed to initialize modlock_init(): No such file or directo ry
eth2: ERROR while getting interface flags: No such device
perform_sysmgr_offline: unable to move MTS to MTS_STATE_OFFLINE: Invalid argumen t (error-id 0x801E0016).
init: failed to initialize modlock_init(): No such file or directory
eth2: ERROR while getting interface flags: No such device
perform_sysmgr_offline: unable to move MTS to MTS_STATE_OFFLINE: Invalid argumen t (error-id 0x801E0016).
init: failed to initialize modlock_init(): No such file or directory
eth2: ERROR while getting interface flags: No such device
perform_sysmgr_offline: unable to move MTS to MTS_STATE_OFFLINE: Invalid argumen t (error-id 0x801E0016).
/isan/sbin/sysmgr: symbol lookup error: /isan/lib/libutils.so: undefined symbol: tftp_callback_fn
Regards
NadeemHi,
I RMAed the appliace, i think it was hardware failure which casue this issue.
If some one face this issue please let me know...Thanks!
Regards
Nad -
Unable to log into the portal-After Upgrade from NetWeaver 7.0 to 7.3EHP1
Dear Experts,
We have poltal landscape(NW 7.0 Dualstack SPS27) with our customozed themes and par files(Company name,logos and colours)
Recently we upgraded the one of portal from NW 7.0 to NW 7.3EHP1 . Upgrade has been successfilly completed with small issue.
After upgrade all urls are working(/nwa, /sld) except /irj/portal.We know that NW 7.3 EHp1 accepts only ear file i.e we converted the our customized log on par file to ear file through par migration tool and the same was deployed successfully through NWDS 7.3 version.After deploying we are able to access the
/irj/portal url with our customized par(means ear file) without issues,
We are unable to log into the portal after giving the correct user id and password,getting the portal runtime error as foloows.
Portal runtime error
An exception occured while processing your request.Send the exception ID your administrator
Exception id:
see log files for details about this exception
Default.trc log file(/server0/log)
#EP-PIN-PRT#tc~epbc~prtc~api#C00061FD2733006C00000005000056CB#9034950000000004#sap.com/com.sap.portal.runtime.system.hooks#com.sap.portal.prt.
runtime#J2EE_ADMIN#4##43E00B85A79911E380F800000089DCC6#3a483a0fa79911e3903000000089dcc6#3a483a0fa79911e3903000000089dcc6#0#Thread[HTTP Worker
[@900472845],5,Dedicated_Application_Thread]#Plain##
08:14_09/03/14_0005_9034950
[EXCEPTION]
java.lang.RuntimeException: Could not create Resource Repository root folder in PCD
at com.sap.portal.resource.repository.ResourceRepositorySrv.initRepositoryRootContext(ResourceRepositorySrv.java:140)
at com.sap.portal.resource.repository.ResourceRepositorySrv.init(ResourceRepositorySrv.java:93)
at com.sap.portal.prt.core.RequestDispatcherFactory$ServiceRequestDispatcher$3.service(RequestDispatcherFactory.java:518)
at com.sap.engine.services.servlets_jsp.server.deploy.impl.module.IRequestDispatcherImpl.dispatch(IRequestDispatcherImpl.java:363)
at com.sap.portal.prt.core.RequestDispatcherFactory$ServiceRequestDispatcher.init(RequestDispatcherFactory.java:503)
at com.sap.portal.prt.broker.PortalServiceItem.initServiceInstance(PortalServiceItem.java:347)
at com.sap.portal.prt.broker.PortalServiceItem.getServiceInstance(PortalServiceItem.java:210)
at com.sap.portal.prt.broker.PortalServiceItem.load(PortalServiceItem.java:578)
at com.sap.portal.prt.om.ObjectsManager.createObejctHandle(ObjectsManager.java:234)
at com.sap.portal.prt.om.ObjectsManager.getObjectHandle(ObjectsManager.java:147)
at com.sap.portal.prt.broker.PortalAppBroker.getPortalService(PortalAppBroker.java:498)
at com.sap.portal.prt.service.ServiceManager.getPortalServiceItem(ServiceManager.java:431)
at com.sap.portal.prt.service.ServiceManager.get(ServiceManager.java:220)
at com.sap.portal.prt.runtime.Portal$RuntimeResources.getService(Portal.java:130)
at com.sap.portal.resource.repository.WebResourceRepositorySrv.init(WebResourceRepositorySrv.java:71)
at com.sap.portal.prt.core.RequestDispatcherFactory$ServiceRequestDispatcher$3.service(RequestDispatcherFactory.java:518)
at com.sap.engine.services.servlets_jsp.server.deploy.impl.module.IRequestDispatcherImpl.dispatch(IRequestDispatcherImpl.java:363)
at com.sap.portal.prt.core.RequestDispatcherFactory$ServiceRequestDispatcher.init(RequestDispatcherFactory.java:503)
at com.sap.portal.prt.broker.PortalServiceItem.initServiceInstance(PortalServiceItem.java:347)
at com.sap.engine.services.servlets_jsp.server.deploy.impl.module.IRequestDispatcherImpl.dispatch(IRequestDispatcherImpl.java:363)
at com.sap.portal.prt.core.RequestDispatcherFactory$ServiceRequestDispatcher.init(RequestDispatcherFactory.java:503)
at com.sap.portal.prt.broker.PortalServiceItem.initServiceInstance(PortalServiceItem.java:347)
at com.sap.portal.prt.broker.PortalServiceItem.getServiceInstance(PortalServiceItem.java:210)
at com.sap.portal.prt.broker.PortalServiceItem.load(PortalServiceItem.java:578)
at com.sap.portal.prt.om.ObjectsManager.createObejctHandle(ObjectsManager.java:234)
at com.sap.portal.prt.om.ObjectsManager.getObjectHandle(ObjectsManager.java:147)
at com.sap.portal.prt.broker.PortalAppBroker.getPortalService(PortalAppBroker.java:498)
at com.sap.portal.prt.service.ServiceManager.getPortalServiceItem(ServiceManager.java:431)
at com.sap.portal.prt.service.ServiceManager.get(ServiceManager.java:220)
at com.sap.portal.prt.runtime.Portal$RuntimeResources.getService(Portal.java:130)
at com.sap.portal.resource.repository.WebResourceImportService$ResourceImporter.<init>(WebResourceImportService.java:248)
at com.sap.portal.resource.repository.WebResourceImportService.importApplicationResources(WebResourceImportService.java:172)
at com.sapportals.portal.navigation.NavigationMimeRepositoryService.loadAllPicsToWRR(NavigationMimeRepositoryService.java:186)
at com.sapportals.portal.navigation.NavigationMimeRepositoryService.init(NavigationMimeRepositoryService.java:160)
at com.sap.portal.prt.core.RequestDispatcherFactory$ServiceRequestDispatcher$3.service(RequestDispatcherFactory.java:518)
at com.sap.engine.services.servlets_jsp.server.deploy.impl.module.IRequestDispatcherImpl.dispatch(IRequestDispatcherImpl.java:363)
at com.sap.portal.prt.core.RequestDispatcherFactory$ServiceRequestDispatcher.init(RequestDispatcherFactory.java:503)
at com.sap.portal.prt.broker.PortalServiceItem.initServiceInstance(PortalServiceItem.java:347)
at com.sap.portal.prt.broker.PortalServiceItem.getServiceInstance(PortalServiceItem.java:210)
at com.sap.portal.prt.broker.PortalServiceItem.load(PortalServiceItem.java:578)
at com.sap.portal.prt.om.ObjectsManager.createObejctHandle(ObjectsManager.java:234)
at com.sap.portal.prt.om.ObjectsManager.getObjectHandle(ObjectsManager.java:147)
at com.sap.portal.prt.broker.PortalAppBroker.getPortalService(PortalAppBroker.java:498)
at com.sap.portal.prt.service.ServiceManager.getPortalServiceItem(ServiceManager.java:431)
at com.sap.portal.prt.service.ServiceManager.get(ServiceManager.java:220)
at com.sap.portal.prt.runtime.Portal$RuntimeResources.getService(Portal.java:130)
at com.sap.portal.pcm.iview.admin.PcmIviewCommon.getAdditionalAttributes(PcmIviewCommon.java:358)
at com.sap.portal.pcm.iview.admin.PcmIviewCommon.initLayers(PcmIviewCommon.java:173)
at com.sap.portal.pcm.iview.admin.AdminBaseiView.createAttrSetLayersList(AdminBaseiView.java:177)
at com.sap.portal.pcm.page.admin.AdminBasePage.getCustomImplementation(AdminBasePage.java:76)
at com.sap.portal.pcm.admin.PcmAdminBase.getImplementation(PcmAdminBase.java:642)
at com.sapportals.portal.navigation.LightningHelperService.getFrameworkPageAttributesValues(LightningHelperService.java:143)
at com.sapportals.portal.navigation.LightningHelperService.getFrameworkPageAttributesValues(LightningHelperService.java:171)
at com.sapportals.portal.navigation.fpm.util.PhaseConfiguration.prepareAttributes(PhaseConfiguration.java:71)
at com.sapportals.portal.navigation.fpm.util.PhaseConfiguration.storeRelatedAttributesInSharedStorage(PhaseConfiguration.java:35)
at com.sapportals.portal.navigation.fpm.NavigationFpmListener.doFrameworkPhase(NavigationFpmListener.java:535)
at com.sapportals.portal.navigation.fpm.NavigationFpmListener.doPhase(NavigationFpmListener.java:122)
at com.sapportals.portal.pb.fpm.FPMContainer.distributeEvent(FPMContainer.java:63)
at com.sapportals.portal.pb.fpm.FPM.doDocumentHook(FPM.java:179)
at com.sapportals.portal.prt.service.document.DocumentHookMulticaster.doDocumentHook(DocumentHookMulticaster.java:100)
at com.sapportals.portal.prt.service.document.DocumentHookService.doDocumentHook(DocumentHookService.java:119)
at com.sapportals.portal.prt.service.document.DocumentHookServiceNew.doDocumentHook(DocumentHookServiceNew.java:186)
at com.sapportals.portal.prt.connection.PortalHook.doDocumentHook(PortalHook.java:665)
at com.sap.portal.prt.core.PortalRequestManager.callPortalComponent(PortalRequestManager.java:183)
at com.sap.portal.prt.core.PortalRequestManager.dispatchRequest(PortalRequestManager.java:107)
at com.sap.portal.prt.core.PortalRequestManager.dispatchRequest(PortalRequestManager.java:141)
at com.sap.portal.prt.component.PortalComponentResponse.include(PortalComponentResponse.java:206)
at com.sapportals.portal.navigation.PortalLauncher.doContent(PortalLauncher.java:116)
at com.sapportals.portal.prt.component.AbstractPortalComponent.serviceDeprecated(AbstractPortalComponent.java:213)
at com.sapportals.portal.prt.component.AbstractPortalComponent.service(AbstractPortalComponent.java:129)
at com.sap.engine.services.httpserver.chain.AbstractChain.process(AbstractChain.java:78)
at com.sap.engine.services.httpserver.filters.MemoryStatisticFilter.process(MemoryStatisticFilter.java:57)
at com.sap.engine.services.httpserver.chain.ServerFilter.process(ServerFilter.java:12)
at com.sap.engine.services.httpserver.chain.AbstractChain.process(AbstractChain.java:78)
at com.sap.engine.services.httpserver.filters.DSRHttpFilter.process(DSRHttpFilter.java:43)
at com.sap.engine.services.httpserver.chain.ServerFilter.process(ServerFilter.java:12)
at com.sap.engine.services.httpserver.chain.AbstractChain.process(AbstractChain.java:78)
at com.sap.engine.services.httpserver.server.Processor.chainedRequest(Processor.java:475)
at com.sap.engine.services.httpserver.server.Processor$FCAProcessorThread.process(Processor.java:269)
at com.sap.engine.services.httpserver.server.rcm.RequestProcessorThread.run(RequestProcessorThread.java:56)
at com.sap.engine.core.thread.execution.Executable.run(Executable.java:122)
at com.sap.engine.core.thread.execution.Executable.run(Executable.java:101)
at com.sap.engine.core.thread.execution.CentralExecutor$SingleThread.run(CentralExecutor.java:328)
Caused by: javax.naming.InvalidNameException: Character not allowed: ':' in 'pcd:resource_repository'
at com.sapportals.portal.pcd.pl.PcdName.checkComponent(PcdName.java:64)
at com.sapportals.portal.pcd.pl.PcdName.checkNameComponent(PcdName.java:39)
at com.sapportals.portal.pcd.pl.PcdName.padd(PcdName.java:636)
at com.sapportals.portal.pcd.pl.PcdName.add(PcdName.java:626)
at com.sapportals.portal.pcd.gl.util.StringUtils.tokenizeIntoPcdName(StringUtils.java:112)
at com.sapportals.portal.pcd.pl.PcdName.appendUrlInternal(PcdName.java:408)
at com.sapportals.portal.pcd.pl.PcdName.<init>(PcdName.java:245)
at com.sap.portal.resource.repository.ResourceRepositorySrv.initRepositoryRootContext(ResourceRepositorySrv.java:121)
... 132 more
1)We are suspecting this issue is related to the theme issue.How to update the theme in the upgraded portal(have a backup of themes)
2)Want to know if we update a theme where it stored at the operating system level(in NW 7.3 EHP1 as well as NW 7.0)
3)Is there any post steps after portal upgrade.
Request you suggest.
Regards
MaruthiHi
Refer the SAP Notes
1942399 - Fix usage of unregistered class loader while processing HTTP request in an application being updated or stopped at the same time
1744820 - Migration 7.3 fails while executing migration of pcd_upgrade
1703578 - WPC migration stops during connection creation
1918086 - ERROR: Unable to get iView
Regards
Ram -
Unable to Login into APEX after upgrade from ORACLE XE to APEX 3.2
Hi,
I have upgraded Oracle 10g XE to with apex_3.2 on the Windows XP.
My ORACLE XE wa in folder "C:\ORACLE XE"
And APEX 3.2 in folder "C:\Ver 3.2\APEX"
Once you complete the standard install, i performd the following steps to complete
the upgrade which i got on my previous post.
Till normal installation i was able to login in Apex link and was able to run my application which was
in oracle XE but the only problem was i was unable to see any images in "EDIT PAGE" but my application was running well.
then i did following steps to get those images
Connect to SQL*Plus as SYS
@APEX_HOME/apex/apxldimg.sql APEX_HOME
@APEX_HOME/apex/apxxepwd.sql password
(where password is the password of the Application Express internal ADMIN account)
I chanbged image directory as below
FROM:
create directory APEX_IMAGES as ‘&1/apex/images’ ;
TO:
create directory APEX_IMAGES as ‘c:\oraclexe\apex\images’ and also tried ‘c:\ver 3.2\apex\images’;
Ran @apxldimg.sql
@apxxepwd.sql password (where password is the password of the Application Express internal ADMIN account)
Exit from the SQL*Plus session.
Change directory to c:\oraclexe\apex\owa, open the README.TXT file and follow the instructions within to complete the installation
But now i am unable to login into the page itself. It "showing Page Not Found"
Please kindly help me how to run APEX now through link.
Thanks in advance.
Thanks & Regards
Sanjay
Edited by: user11204334 on Aug 11, 2009 2:05 AM
Edited by: user11204334 on Aug 11, 2009 4:30 AMHi John,
Thanks for reply
I got error while doing following steps in few procedures
Change directory to c:\oraclexe\apex\owa, open the README.TXT file and follow the instructions within to complete the installation
Before doing the above step i was able to login into my application but without images
Can you please help that how to check those errors and any particular procedure you know which is responsible for the Login problem.
Thanks a Lot for help John
Thanks & Regards
Sanjay -
I am unable to sign into my google account after a tower being down. Any ideas
Using FaceTime http://support.apple.com/kb/ht4319
Troubleshooting FaceTime http://support.apple.com/kb/TS3367
The Complete Guide to FaceTime: Set-up, Use, and Troubleshooting Problems
http://tinyurl.com/32drz3d
Cheers, Tom -
CUPC – Unable to go into deskphone control mode and unable to chat
Home Lab – learning Presence
CUCM 9
CUPS 9 (not 8.6 as virtually all of the help and discussion forums, documents, etc are for)
CUPC 8.6 (3 copies running on 3 different laptops)
4 users configured in CUCM for Presence capabilities
No LDAP integration
Current status:
Presence indicators for phones works fine, no issues
3 users can log into their CUPC clients and Presence information from their own associated deskphone displays correctly (ie if User 1 takes his deskphone offhook, the CUPC for User 1 shows as “On the Phone”
Users can place phone calls with each other by typing the DN in the “Search for name or number” field
I have two different issues that I have not been able to solve all day – they may be related to each other.
The first issue: I am unable to go into deskphone mode. Although the checkbox is visible – it appears to be greyed out and clicking in it does nothing.
The second issue: I am unable to start a chat session. I highlite a contact (that I manually entered), right click, and select chat. I get an error message that says “Failed to start conversation. Invalid parameter”
I have scoured the Cisco site for docs and most of them pertain to CUPS 8.6 and not 9. There is a difference in that v9 does not have the Application -> IP Phone Messenger selection.
My current configs:
CUCM
4 application users – CUPS-AXL (with Stand CCM SuperUsers permissions), CUPS-Deskphone, CUPS-CTIGW, and CUPS-PhoneMSG (all with Standard CTI Allow control of all devices).
3 end users – From top to bottom, all users have passwords and digest credentials. Under Service Settings, all users have the “Enable user for Unified CM IM and Presence” checked. This is the replacement for the assigning license capabilities from version 8.6. Also under Service Settings, all users have a UC Service Profile assigned. The UC Service Profile has two UC service settings – a Presence and IM Profile and a CTI Profile. Under Device Information – all user have been associated to two different devices (their hardphone and the CUPC client). Under the Directory Number Association portion – each user has their own primary line selected from the drop down box. Under the Permissions Information section - each user has Standard CCM End Users and Standard CTI Enabled permissions.
Devices – each user has a 7960 hard phone and a CUPC. For each device (both types) at the Device Level -> Owner User ID, Protocol Specific Information -> BLF Presence Group, SUBSCRIBE CSS are all set. Under the line for each device (both types) – Allow control of device from CTI is checked, in the Associated Devices window is the MAC and UPC<name> of the devices, Under Users Associated with Line is the correct user
Under System –> Application Server, the CUP server is configured.
Under System -> Licensing, all users and devices are licensed. There is no Capabilities Assignment in version 9
CUPS
Under Diagnostics -> System Troubleshooter -> all green except for the things not configured, LDAP, 3rd party, etc
User Management -> End User -> are licensed for IM and Presence and have Microsoft RCC enabled. They also show 2 devices
Under Application – this is where its different from v8 to v9.
Application -> Legacy Clients -> Settings. I have set the TFTP server IP to the CUCM
Application -> Legacy Clients -> CCMCIP Profile. I created a new profile, set the Primary and Secondary CCMCIP Host to be the IP Address of the CUCM Publisher. For Server Certification Verfication, I selected Any Certificate from the drop down. I assigned this profile to all 4 of my users.
Application -> Microsoft RCC settings. Application status = on. For Application Username and password, I have tried using CUPS-Deskphone and CUPS-CTIGW with their appropriate passwords. There is not difference in using either one of them. CUCM address is address of my Pub. I assigned this Microsoft RCC service to all 4 of my users.
So, as I said, I have been working on this all day today burning my fingers and my mouse up on Google. To no avail.
Any ideas anyone?
JeffUpdate –
Well, I finally bit the bullet and stood up a MS AD domain in my lab.
I integrated CUCM into the LDAP and imported the users from LDAP
I also stood up a DNS server.
I reconfigured CUPS to the new domain, joined all of the endpoint laptops to the domain, and retested.
Same place as I was before with the deskphone mode – however, my ability to IM is fixed (as was expected).
Using CUPS, I am not able to go into deskphone control mode. The option box is still greyed out.
However, I installed Jabber for Windows on the same laptops.
In Jabber, I am able to select the option at the bottom of the window to use my deskphone for calls, and then I can move it back to the Jabber client.
So, anyone have any ideas why CUPC refuses to let me go into deskphone control mode?
All features and functions of the JFW work great. No problems.
Jeff -
I am trying to create an account and I am unable to type into the password box.
When I try to create a new account I am unable to type into the password text box. I can enter my email and I can type int he security wquestion box. I have Windows 7, the current version of iTunes and its a fairly powerful PC. Please help!
Same problem. Wasted 2 hours so far! I use my personal email for registering all my HP products and can log-in to that fine. Trying to use same personal email for eprint seems to be problem.
-
unable to sign into icloud account from my windows 7 pc. keep on getting the message serwr not available
Hi,
In the Finder use the Go Menu whilst holding down the ALT key.
Select the Library that appears when you do this.
Navigate to Containers/com.apple.soagent/Data/Library/Preferences
You will notice that many of the items are Aliases (to the Originals in ~/Library/Preferences).
But there are exceptions.
Delete (Drag to Trash) the com.apple.soagent.plist and com.apple.messageshelper.AccountInfoController.plist
Restart the Mac (I have not worked out is SOAgent launches when the Mac does).
Restart Messages.
If this does not work navigate to ~/Library/Preferences
In here find and Delete com.apple.ids.service.com.apple.madrid.plist
This will need a Restart of the app.
You will be asked Again for your Apple ID
9:28 pm Sunday; January 26, 2014
iMac 2.5Ghz 5i 2011 (Mavericks 10.9)
G4/1GhzDual MDD (Leopard 10.5.8)
MacBookPro 2Gb (Snow Leopard 10.6.8)
Mac OS X (10.6.8),
Couple of iPhones and an iPad -
I'm locked out of my iPhone. My 4 digit security code is not working. I've tried to connect to iTunes to do a recovery however I. Order to do this it asks me for the 4 digit code. I need to reset it but unable to get into reset as well. Help!!t can I reset it using my iPad which is registered to the same account
See Here > http://support.apple.com/kb/HT1808
You may need to try this More than Once... Be sure to Follow ALL the Steps.. -
Crystal Reports Server 2008 trial install - unable to log into CMC
Hi,
I have been looking for a way to host my existing Crystal XI reports on our in house web application rather than using a thick client application with cview. I was told that the options were Crystal Reports Server 2008 or Visual Studio 2008. I have downloaded trials of both and am currently testing.
After installing Crystal Reports Server 2008, including MySQL DB and Tomcat web server, i am unable to log into any of the applications with the error that:
Error: Server SCOTTPC:6400 not found or server may be down (FWM 01003) null
After seeing this i checked the services on my test machine and found that the Server Intelligence Agent was not started. So i tried starting it and recieved the generic windows message:
Service on local computer started and them stopped. Some services stop automatically if they have no work to do ... etc
After multiple reboots and reinstalls i am still unable to use any aspect of the application as i am unable to log into the CMC as the server is down. Now i am new to Crystal reports and web servers so have a very limited knowledge of whats going on here - i am primarily a DBA. From what i can tell MySQL does not even appear to be installed but i cannot be sure.
Any suggestions?ok... after research it seems a DSN has not been created.
Also when trying to start the server intelligence service i see the following in the application event viewer:
[Node Name: SCOTTPC]
[User Name: SYSTEM]
Server Intelligence Agent has failed to initialize because the bootstrap file C:\Program Files\Business Objects\BusinessObjects Enterprise 12.0\win32_x86\_boe_SCOTTPC.bootstrap is missing information about the CMS cluster. Please restore your bootstrap file from your backup.
i have recreated the bootstrap file but still get the same error.
i have SQL Server 2005 installed on this rig as well - could this be causing the issue? Would it be better for me to integrate this to SQL Server rather than using the MySQL DB that comes with Crystal server 2008? -
I am receiving an Activation Error and unable to get into my phone.It's asking me to register my phone in the iPhone Developer program however I'm already registered. How do I move forward?
Hi, jsgladden.
Here is an article I would recommend when experiencing issues activating a device. The step referring to recovery mode usually resolves the issue.
iPhone: Troubleshooting activation issues
http://support.apple.com/kb/TS3424
To retrieve your data, you will need to restore from backup after processing these steps. Here is the article that walks you through restoring from either your iCloud or iTunes backup.
iOS: How to back up and restore your content
http://support.apple.com/kb/HT1766
Cheers,
Jason H. -
I am unable to sign into my account through Adobe Elements 12. I can sign in on Adobe's website, and through Revel online, and through my smartphone, however when I try to sign in through Adobe Elements 12 directly, the hourglass never stops turning, and turning.
Hi,
Have you tried working through this document - it does apply to Elements as well.
Sign in, activation, or connection errors | CS5.5 and later
If you still have problems you may need to contact the Adobe activation team - see the "Still need help?" link at the end of the document.
Good luck
Brian -
I changed the main email on my Appleid a few months back. Everything worked fine until uppgrading to iOS7 on my phone. I am now unable to log into iCloud because the old email pops up and requesting password which is not working. I cannot rest the password because my old email is unvalid as I have changed network provider. The id works fine on Appstore and iTunes so its only iCloud that making trouble.
Any suggestions to remedy this problem?I'm also experiencing the same issue.
I've had to reset my password 3 times in the last 3 days.
At first, I couldn't get my email. I sweated it out for 12 hours, reset my password and I was good to go again. 48 hours later, I ran into the same issue. Only problem is, not only do I get the 'Incorrect username or password' on my device, but my iCloud.com login no longer works. so now I can't read my messages on the web OR on my device/computer.
I have went to appleid.apple.com and reset my password there: no luck.
I have reset the settings on my device: no luck.
I have Erase and Installed iOS 6.1.2: no luck.
I have restored my device back to factory settings: no luck.
I have performed a DFU restore: no luck.
This is my main account for, well everything. -
Hello All, During an investigation Application user RMCM was found to be deleted from CUCM as per CUCM logs but the first issue of agents unable to log into ACD queue was reported 2 weeks later following a publisher reboot, I am trying to understand what could have caused this ? The reboot obviously could not have made any changes but the logs says RMCM users deleted on 09 May but issue was reported on 20 May and in the meantime services were said to be working without interruption . Can i have some suggestion to understand this to explain customer ?
The RMCM user being deleted might not have triggered a JTAPI update on the UCCX side. The publisher reboot which restarted CTIManager would have definitely triggered the update and forced UCCX to re-authenticate with the now non-existent user.
Maybe you are looking for
-
Hi Experts, we have created custom field in SAles order and try to maintain a F4 help for that. we have created Search help with search help exit,when we click on F4 help the values are getting populated currectly in the pop-up in UI. issue is when
-
Hello guys! As you know, i'm new to VB. For my next challenge, i would like to create a program that goes through the numbers 1 to 100, and if they are divisible by 5, print them as well as the running total. If they can't be divided, then they're st
-
ERROR WHILE PRODUCT GROUP CREATION
Dear All, I am trying to creat the product Group but system is giving the following error. Message No.M3749 "Required parameters missing when calling up module". Please give your valuable input to overcome the issue. Thanks & Regards, Vijay Mankar +9
-
Protected Methods in Interfaces
Why don't interfaces allow you to declare protected methods? Is there a way around this? The reason I ask involves a current project of mine. I have an inheritance hierarchy including an abstract Event base class with many concrete derived Events. I
-
Any way to add metadata to a jpeg without resaving the file?
I was surprised that opening a jpeg and looking at meta info, if I just added a word. PS ask to resave the file at what setting. Too much of a nuisance. Any ideas thanks! I know I could go back to the tiffs or psd, but these are watermarked already